| /** |
| ****************************************************************************** |
| * @file stm32l4xx_hal_can_legacy.h |
| * @author MCD Application Team |
| * @brief Header file of CAN HAL module. |
| ****************************************************************************** |
| * @attention |
| * |
| * <h2><center>© Copyright (c) 2017 STMicroelectronics. |
| * All rights reserved.</center></h2> |
| * |
| * This software component is licensed by ST under BSD 3-Clause license, |
| * the "License"; You may not use this file except in compliance with the |
| * License. You may obtain a copy of the License at: |
| * opensource.org/licenses/BSD-3-Clause |
| * |
| ****************************************************************************** |
| */ |
| |
| /* Define to prevent recursive inclusion -------------------------------------*/ |
| #ifndef __STM32L4xx_CAN_LEGACY_H |
| #define __STM32L4xx_CAN_LEGACY_H |
| |
| #ifdef __cplusplus |
| extern "C" { |
| #endif |
| |
| #if defined(CAN1) |
| /* Includes ------------------------------------------------------------------*/ |
| #include "stm32l4xx_hal_def.h" |
| |
| /** @addtogroup STM32L4xx_HAL_Driver |
| * @{ |
| */ |
| |
| /** @addtogroup CAN |
| * @{ |
| */ |
| |
| /* Exported types ------------------------------------------------------------*/ |
| /** @defgroup CAN_Exported_Types CAN Exported Types |
| * @{ |
| */ |
| |
| /** |
| * @brief HAL State structures definition |
| */ |
| typedef enum |
| { |
| HAL_CAN_STATE_RESET = 0x00, /*!< CAN not yet initialized or disabled */ |
| HAL_CAN_STATE_READY = 0x01, /*!< CAN initialized and ready for use */ |
| HAL_CAN_STATE_BUSY = 0x02, /*!< CAN process is ongoing */ |
| HAL_CAN_STATE_BUSY_TX = 0x12, /*!< CAN process is ongoing */ |
| HAL_CAN_STATE_BUSY_RX = 0x22, /*!< CAN process is ongoing */ |
| HAL_CAN_STATE_BUSY_TX_RX = 0x32, /*!< CAN process is ongoing */ |
| HAL_CAN_STATE_TIMEOUT = 0x03, /*!< Timeout state */ |
| HAL_CAN_STATE_ERROR = 0x04 /*!< CAN error state */ |
| |
| }HAL_CAN_StateTypeDef; |
| |
| /** |
| * @brief CAN init structure definition |
| */ |
| typedef struct |
| { |
| uint32_t Prescaler; /*!< Specifies the length of a time quantum. |
| This parameter must be a number between Min_Data = 1 and Max_Data = 1024 */ |
| |
| uint32_t Mode; /*!< Specifies the CAN operating mode. |
| This parameter can be a value of @ref CAN_operating_mode */ |
| |
| uint32_t SJW; /*!< Specifies the maximum number of time quanta |
| the CAN hardware is allowed to lengthen or |
| shorten a bit to perform resynchronization. |
| This parameter can be a value of @ref CAN_synchronisation_jump_width */ |
| |
| uint32_t BS1; /*!< Specifies the number of time quanta in Bit Segment 1. |
| This parameter can be a value of @ref CAN_time_quantum_in_bit_segment_1 */ |
| |
| uint32_t BS2; /*!< Specifies the number of time quanta in Bit Segment 2. |
| This parameter can be a value of @ref CAN_time_quantum_in_bit_segment_2 */ |
| |
| uint32_t TTCM; /*!< Enable or disable the time triggered communication mode. |
| This parameter can be set to ENABLE or DISABLE. */ |
| |
| uint32_t ABOM; /*!< Enable or disable the automatic bus-off management. |
| This parameter can be set to ENABLE or DISABLE */ |
| |
| uint32_t AWUM; /*!< Enable or disable the automatic wake-up mode. |
| This parameter can be set to ENABLE or DISABLE */ |
| |
| uint32_t NART; /*!< Enable or disable the non-automatic retransmission mode. |
| This parameter can be set to ENABLE or DISABLE */ |
| |
| uint32_t RFLM; /*!< Enable or disable the receive FIFO Locked mode. |
| This parameter can be set to ENABLE or DISABLE */ |
| |
| uint32_t TXFP; /*!< Enable or disable the transmit FIFO priority. |
| This parameter can be set to ENABLE or DISABLE */ |
| }CAN_InitTypeDef; |
| |
| /** |
| * @brief CAN filter configuration structure definition |
| */ |
| typedef struct |
| { |
| uint32_t FilterIdHigh; /*!< Specifies the filter identification number (MSBs for a 32-bit |
| configuration, first one for a 16-bit configuration). |
| This parameter must be a number between Min_Data = 0x0000 and Max_Data = 0xFFFF */ |
| |
| uint32_t FilterIdLow; /*!< Specifies the filter identification number (LSBs for a 32-bit |
| configuration, second one for a 16-bit configuration). |
| This parameter must be a number between Min_Data = 0x0000 and Max_Data = 0xFFFF */ |
| |
| uint32_t FilterMaskIdHigh; /*!< Specifies the filter mask number or identification number, |
| according to the mode (MSBs for a 32-bit configuration, |
| first one for a 16-bit configuration). |
| This parameter must be a number between Min_Data = 0x0000 and Max_Data = 0xFFFF */ |
| |
| uint32_t FilterMaskIdLow; /*!< Specifies the filter mask number or identification number, |
| according to the mode (LSBs for a 32-bit configuration, |
| second one for a 16-bit configuration). |
| This parameter must be a number between Min_Data = 0x0000 and Max_Data = 0xFFFF */ |
| |
| uint32_t FilterFIFOAssignment; /*!< Specifies the FIFO (0 or 1) which will be assigned to the filter. |
| This parameter can be a value of @ref CAN_filter_FIFO */ |
| |
| uint32_t FilterNumber; /*!< Specifies the filter which will be initialized. |
| This parameter must be a number between Min_Data = 0 and Max_Data = 27 */ |
| |
| uint32_t FilterMode; /*!< Specifies the filter mode to be initialized. |
| This parameter can be a value of @ref CAN_filter_mode */ |
| |
| uint32_t FilterScale; /*!< Specifies the filter scale. |
| This parameter can be a value of @ref CAN_filter_scale */ |
| |
| uint32_t FilterActivation; /*!< Enable or disable the filter. |
| This parameter can be set to ENABLE or DISABLE */ |
| |
| uint32_t BankNumber; /*!< Select the start slave bank filter. |
| This parameter must be a number between Min_Data = 0 and Max_Data = 28 */ |
| |
| }CAN_FilterConfTypeDef; |
| |
| /** |
| * @brief CAN Tx message structure definition |
| */ |
| typedef struct |
| { |
| uint32_t StdId; /*!< Specifies the standard identifier. |
| This parameter must be a number between Min_Data = 0 and Max_Data = 0x7FF */ |
| |
| uint32_t ExtId; /*!< Specifies the extended identifier. |
| This parameter must be a number between Min_Data = 0 and Max_Data = 0x1FFFFFFF */ |
| |
| uint32_t IDE; /*!< Specifies the type of identifier for the message that will be transmitted. |
| This parameter can be a value of @ref CAN_identifier_type */ |
| |
| uint32_t RTR; /*!< Specifies the type of frame for the message that will be transmitted. |
| This parameter can be a value of @ref CAN_remote_transmission_request */ |
| |
| uint32_t DLC; /*!< Specifies the length of the frame that will be transmitted. |
| This parameter must be a number between Min_Data = 0 and Max_Data = 8 */ |
| |
| uint8_t Data[8]; /*!< Contains the data to be transmitted. |
| This parameter must be a number between Min_Data = 0 and Max_Data = 0xFF */ |
| |
| }CanTxMsgTypeDef; |
| |
| /** |
| * @brief CAN Rx message structure definition |
| */ |
| typedef struct |
| { |
| uint32_t StdId; /*!< Specifies the standard identifier. |
| This parameter must be a number between Min_Data = 0 and Max_Data = 0x7FF */ |
| |
| uint32_t ExtId; /*!< Specifies the extended identifier. |
| This parameter must be a number between Min_Data = 0 and Max_Data = 0x1FFFFFFF */ |
| |
| uint32_t IDE; /*!< Specifies the type of identifier for the message that will be received. |
| This parameter can be a value of @ref CAN_identifier_type */ |
| |
| uint32_t RTR; /*!< Specifies the type of frame for the received message. |
| This parameter can be a value of @ref CAN_remote_transmission_request */ |
| |
| uint32_t DLC; /*!< Specifies the length of the frame that will be received. |
| This parameter must be a number between Min_Data = 0 and Max_Data = 8 */ |
| |
| uint8_t Data[8]; /*!< Contains the data to be received. |
| This parameter must be a number between Min_Data = 0 and Max_Data = 0xFF */ |
| |
| uint32_t FMI; /*!< Specifies the index of the filter the message stored in the mailbox passes through. |
| This parameter must be a number between Min_Data = 0 and Max_Data = 0xFF */ |
| |
| uint32_t FIFONumber; /*!< Specifies the receive FIFO number. |
| This parameter can be CAN_FIFO0 or CAN_FIFO1 */ |
| |
| }CanRxMsgTypeDef; |
| |
| /** |
| * @brief CAN handle Structure definition |
| */ |
| typedef struct |
| { |
| CAN_TypeDef *Instance; /*!< Register base address */ |
| |
| CAN_InitTypeDef Init; /*!< CAN required parameters */ |
| |
| CanTxMsgTypeDef* pTxMsg; /*!< Pointer to transmit structure */ |
| |
| CanRxMsgTypeDef* pRxMsg; /*!< Pointer to reception structure */ |
| |
| __IO HAL_CAN_StateTypeDef State; /*!< CAN communication state */ |
| |
| HAL_LockTypeDef Lock; /*!< CAN locking object */ |
| |
| __IO uint32_t ErrorCode; /*!< CAN Error code */ |
| |
| }CAN_HandleTypeDef; |
| |
| /** |
| * @} |
| */ |
| |
| /* Exported constants --------------------------------------------------------*/ |
| /** @defgroup CAN_Exported_Constants CAN Exported Constants |
| * @{ |
| */ |
| |
| /** @defgroup CAN_Error_Code CAN Error Code |
| * @{ |
| */ |
| #define HAL_CAN_ERROR_NONE ((uint32_t)0x00000000) /*!< No error */ |
| #define HAL_CAN_ERROR_EWG ((uint32_t)0x00000001) /*!< EWG error */ |
| #define HAL_CAN_ERROR_EPV ((uint32_t)0x00000002) /*!< EPV error */ |
| #define HAL_CAN_ERROR_BOF ((uint32_t)0x00000004) /*!< BOF error */ |
| #define HAL_CAN_ERROR_STF ((uint32_t)0x00000008) /*!< Stuff error */ |
| #define HAL_CAN_ERROR_FOR ((uint32_t)0x00000010) /*!< Form error */ |
| #define HAL_CAN_ERROR_ACK ((uint32_t)0x00000020) /*!< Acknowledgment error */ |
| #define HAL_CAN_ERROR_BR ((uint32_t)0x00000040) /*!< Bit recessive */ |
| #define HAL_CAN_ERROR_BD ((uint32_t)0x00000080) /*!< LEC dominant */ |
| #define HAL_CAN_ERROR_CRC ((uint32_t)0x00000100) /*!< LEC transfer error */ |
| #define HAL_CAN_ERROR_FOV0 ((uint32_t)0x00000200) /*!< FIFO0 overrun error */ |
| #define HAL_CAN_ERROR_FOV1 ((uint32_t)0x00000400) /*!< FIFO1 overrun error */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup CAN_InitStatus CAN initialization Status |
| * @{ |
| */ |
| #define CAN_INITSTATUS_FAILED ((uint32_t)0x00000000) /*!< CAN initialization failed */ |
| #define CAN_INITSTATUS_SUCCESS ((uint32_t)0x00000001) /*!< CAN initialization OK */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup CAN_operating_mode CAN Operating Mode |
| * @{ |
| */ |
| #define CAN_MODE_NORMAL ((uint32_t)0x00000000) /*!< Normal mode */ |
| #define CAN_MODE_LOOPBACK ((uint32_t)CAN_BTR_LBKM) /*!< Loopback mode */ |
| #define CAN_MODE_SILENT ((uint32_t)CAN_BTR_SILM) /*!< Silent mode */ |
| #define CAN_MODE_SILENT_LOOPBACK ((uint32_t)(CAN_BTR_LBKM | CAN_BTR_SILM)) /*!< Loopback combined with silent mode */ |
| /** |
| * @} |
| */ |
| |
| |
| /** @defgroup CAN_synchronisation_jump_width CAN Synchronization Jump Width |
| * @{ |
| */ |
| #define CAN_SJW_1TQ ((uint32_t)0x00000000) /*!< 1 time quantum */ |
| #define CAN_SJW_2TQ ((uint32_t)CAN_BTR_SJW_0) /*!< 2 time quantum */ |
| #define CAN_SJW_3TQ ((uint32_t)CAN_BTR_SJW_1) /*!< 3 time quantum */ |
| #define CAN_SJW_4TQ ((uint32_t)CAN_BTR_SJW) /*!< 4 time quantum */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup CAN_time_quantum_in_bit_segment_1 CAN Time Quantum in Bit Segment 1 |
| * @{ |
| */ |
| #define CAN_BS1_1TQ ((uint32_t)0x00000000) /*!< 1 time quantum */ |
| #define CAN_BS1_2TQ ((uint32_t)CAN_BTR_TS1_0) /*!< 2 time quantum */ |
| #define CAN_BS1_3TQ ((uint32_t)CAN_BTR_TS1_1) /*!< 3 time quantum */ |
| #define CAN_BS1_4TQ ((uint32_t)(CAN_BTR_TS1_1 | CAN_BTR_TS1_0)) /*!< 4 time quantum */ |
| #define CAN_BS1_5TQ ((uint32_t)CAN_BTR_TS1_2) /*!< 5 time quantum */ |
| #define CAN_BS1_6TQ ((uint32_t)(CAN_BTR_TS1_2 | CAN_BTR_TS1_0)) /*!< 6 time quantum */ |
| #define CAN_BS1_7TQ ((uint32_t)(CAN_BTR_TS1_2 | CAN_BTR_TS1_1)) /*!< 7 time quantum */ |
| #define CAN_BS1_8TQ ((uint32_t)(CAN_BTR_TS1_2 | CAN_BTR_TS1_1 | CAN_BTR_TS1_0)) /*!< 8 time quantum */ |
| #define CAN_BS1_9TQ ((uint32_t)CAN_BTR_TS1_3) /*!< 9 time quantum */ |
| #define CAN_BS1_10TQ ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_0)) /*!< 10 time quantum */ |
| #define CAN_BS1_11TQ ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_1)) /*!< 11 time quantum */ |
| #define CAN_BS1_12TQ ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_1 | CAN_BTR_TS1_0)) /*!< 12 time quantum */ |
| #define CAN_BS1_13TQ ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_2)) /*!< 13 time quantum */ |
| #define CAN_BS1_14TQ ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_2 | CAN_BTR_TS1_0)) /*!< 14 time quantum */ |
| #define CAN_BS1_15TQ ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_2 | CAN_BTR_TS1_1)) /*!< 15 time quantum */ |
| #define CAN_BS1_16TQ ((uint32_t)CAN_BTR_TS1) /*!< 16 time quantum */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup CAN_time_quantum_in_bit_segment_2 CAN Time Quantum in Bit Segment 2 |
| * @{ |
| */ |
| #define CAN_BS2_1TQ ((uint32_t)0x00000000) /*!< 1 time quantum */ |
| #define CAN_BS2_2TQ ((uint32_t)CAN_BTR_TS2_0) /*!< 2 time quantum */ |
| #define CAN_BS2_3TQ ((uint32_t)CAN_BTR_TS2_1) /*!< 3 time quantum */ |
| #define CAN_BS2_4TQ ((uint32_t)(CAN_BTR_TS2_1 | CAN_BTR_TS2_0)) /*!< 4 time quantum */ |
| #define CAN_BS2_5TQ ((uint32_t)CAN_BTR_TS2_2) /*!< 5 time quantum */ |
| #define CAN_BS2_6TQ ((uint32_t)(CAN_BTR_TS2_2 | CAN_BTR_TS2_0)) /*!< 6 time quantum */ |
| #define CAN_BS2_7TQ ((uint32_t)(CAN_BTR_TS2_2 | CAN_BTR_TS2_1)) /*!< 7 time quantum */ |
| #define CAN_BS2_8TQ ((uint32_t)CAN_BTR_TS2) /*!< 8 time quantum */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup CAN_filter_mode CAN Filter Mode |
| * @{ |
| */ |
| #define CAN_FILTERMODE_IDMASK ((uint8_t)0x00) /*!< Identifier mask mode */ |
| #define CAN_FILTERMODE_IDLIST ((uint8_t)0x01) /*!< Identifier list mode */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup CAN_filter_scale CAN Filter Scale |
| * @{ |
| */ |
| #define CAN_FILTERSCALE_16BIT ((uint8_t)0x00) /*!< Two 16-bit filters */ |
| #define CAN_FILTERSCALE_32BIT ((uint8_t)0x01) /*!< One 32-bit filter */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup CAN_filter_FIFO CAN Filter FIFO |
| * @{ |
| */ |
| #define CAN_FILTER_FIFO0 ((uint8_t)0x00) /*!< Filter FIFO 0 assignment for filter x */ |
| #define CAN_FILTER_FIFO1 ((uint8_t)0x01) /*!< Filter FIFO 1 assignment for filter x */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup CAN_identifier_type CAN Identifier Type |
| * @{ |
| */ |
| #define CAN_ID_STD ((uint32_t)0x00000000) /*!< Standard Id */ |
| #define CAN_ID_EXT ((uint32_t)0x00000004) /*!< Extended Id */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup CAN_remote_transmission_request CAN Remote Transmission Request |
| * @{ |
| */ |
| #define CAN_RTR_DATA ((uint32_t)0x00000000) /*!< Data frame */ |
| #define CAN_RTR_REMOTE ((uint32_t)0x00000002) /*!< Remote frame */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup CAN_receive_FIFO_number_constants CAN Receive FIFO Number |
| * @{ |
| */ |
| #define CAN_FIFO0 ((uint8_t)0x00) /*!< CAN FIFO 0 used to receive */ |
| #define CAN_FIFO1 ((uint8_t)0x01) /*!< CAN FIFO 1 used to receive */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup CAN_flags CAN Flags |
| * @{ |
| */ |
| /* If the flag is 0x3XXXXXXX, it means that it can be used with CAN_GetFlagStatus() |
| and CAN_ClearFlag() functions. */ |
| /* If the flag is 0x1XXXXXXX, it means that it can only be used with |
| CAN_GetFlagStatus() function. */ |
| |
| /* Transmit Flags */ |
| #define CAN_FLAG_RQCP0 ((uint32_t)0x00000500) /*!< Request MailBox0 flag */ |
| #define CAN_FLAG_RQCP1 ((uint32_t)0x00000508) /*!< Request MailBox1 flag */ |
| #define CAN_FLAG_RQCP2 ((uint32_t)0x00000510) /*!< Request MailBox2 flag */ |
| #define CAN_FLAG_TXOK0 ((uint32_t)0x00000501) /*!< Transmission OK MailBox0 flag */ |
| #define CAN_FLAG_TXOK1 ((uint32_t)0x00000509) /*!< Transmission OK MailBox1 flag */ |
| #define CAN_FLAG_TXOK2 ((uint32_t)0x00000511) /*!< Transmission OK MailBox2 flag */ |
| #define CAN_FLAG_TME0 ((uint32_t)0x0000051A) /*!< Transmit mailbox 0 empty flag */ |
| #define CAN_FLAG_TME1 ((uint32_t)0x0000051B) /*!< Transmit mailbox 0 empty flag */ |
| #define CAN_FLAG_TME2 ((uint32_t)0x0000051C) /*!< Transmit mailbox 0 empty flag */ |
| |
| /* Receive Flags */ |
| #define CAN_FLAG_FF0 ((uint32_t)0x00000203) /*!< FIFO 0 Full flag */ |
| #define CAN_FLAG_FOV0 ((uint32_t)0x00000204) /*!< FIFO 0 Overrun flag */ |
| |
| #define CAN_FLAG_FF1 ((uint32_t)0x00000403) /*!< FIFO 1 Full flag */ |
| #define CAN_FLAG_FOV1 ((uint32_t)0x00000404) /*!< FIFO 1 Overrun flag */ |
| |
| /* Operating Mode Flags */ |
| #define CAN_FLAG_WKU ((uint32_t)0x00000103) /*!< Wake up flag */ |
| #define CAN_FLAG_SLAK ((uint32_t)0x00000101) /*!< Sleep acknowledge flag */ |
| #define CAN_FLAG_SLAKI ((uint32_t)0x00000104) /*!< Sleep acknowledge flag */ |
| /* @note When SLAK interrupt is disabled (SLKIE=0), no polling on SLAKI is possible. |
| In this case the SLAK bit can be polled.*/ |
| |
| /* Error Flags */ |
| #define CAN_FLAG_EWG ((uint32_t)0x00000300) /*!< Error warning flag */ |
| #define CAN_FLAG_EPV ((uint32_t)0x00000301) /*!< Error passive flag */ |
| #define CAN_FLAG_BOF ((uint32_t)0x00000302) /*!< Bus-Off flag */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup CAN_interrupts CAN Interrupts |
| * @{ |
| */ |
| #define CAN_IT_TME ((uint32_t)CAN_IER_TMEIE) /*!< Transmit mailbox empty interrupt */ |
| |
| /* Receive Interrupts */ |
| #define CAN_IT_FMP0 ((uint32_t)CAN_IER_FMPIE0) /*!< FIFO 0 message pending interrupt */ |
| #define CAN_IT_FF0 ((uint32_t)CAN_IER_FFIE0) /*!< FIFO 0 full interrupt */ |
| #define CAN_IT_FOV0 ((uint32_t)CAN_IER_FOVIE0) /*!< FIFO 0 overrun interrupt */ |
| #define CAN_IT_FMP1 ((uint32_t)CAN_IER_FMPIE1) /*!< FIFO 1 message pending interrupt */ |
| #define CAN_IT_FF1 ((uint32_t)CAN_IER_FFIE1) /*!< FIFO 1 full interrupt */ |
| #define CAN_IT_FOV1 ((uint32_t)CAN_IER_FOVIE1) /*!< FIFO 1 overrun interrupt */ |
| |
| /* Operating Mode Interrupts */ |
| #define CAN_IT_WKU ((uint32_t)CAN_IER_WKUIE) /*!< Wake-up interrupt */ |
| #define CAN_IT_SLK ((uint32_t)CAN_IER_SLKIE) /*!< Sleep acknowledge interrupt */ |
| |
| /* Error Interrupts */ |
| #define CAN_IT_EWG ((uint32_t)CAN_IER_EWGIE) /*!< Error warning interrupt */ |
| #define CAN_IT_EPV ((uint32_t)CAN_IER_EPVIE) /*!< Error passive interrupt */ |
| #define CAN_IT_BOF ((uint32_t)CAN_IER_BOFIE) /*!< Bus-off interrupt */ |
| #define CAN_IT_LEC ((uint32_t)CAN_IER_LECIE) /*!< Last error code interrupt */ |
| #define CAN_IT_ERR ((uint32_t)CAN_IER_ERRIE) /*!< Error Interrupt */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Mailboxes definition */ |
| #define CAN_TXMAILBOX_0 ((uint8_t)0x00) |
| #define CAN_TXMAILBOX_1 ((uint8_t)0x01) |
| #define CAN_TXMAILBOX_2 ((uint8_t)0x02) |
| |
| /** |
| * @} |
| */ |
| |
| /* Exported macros -----------------------------------------------------------*/ |
| /** @defgroup CAN_Exported_Macro CAN Exported Macros |
| * @{ |
| */ |
| |
| /** @brief Reset CAN handle state. |
| * @param __HANDLE__: CAN handle. |
| * @retval None |
| */ |
| #define __HAL_CAN_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_CAN_STATE_RESET) |
| |
| /** |
| * @brief Enable the specified CAN interrupt. |
| * @param __HANDLE__: CAN handle. |
| * @param __INTERRUPT__: CAN Interrupt. |
| * @retval None |
| */ |
| #define __HAL_CAN_ENABLE_IT(__HANDLE__, __INTERRUPT__) (((__HANDLE__)->Instance->IER) |= (__INTERRUPT__)) |
| |
| /** |
| * @brief Disable the specified CAN interrupt. |
| * @param __HANDLE__: CAN handle. |
| * @param __INTERRUPT__: CAN Interrupt. |
| * @retval None |
| */ |
| #define __HAL_CAN_DISABLE_IT(__HANDLE__, __INTERRUPT__) (((__HANDLE__)->Instance->IER) &= ~(__INTERRUPT__)) |
| |
| /** |
| * @brief Return the number of pending received messages. |
| * @param __HANDLE__: CAN handle. |
| * @param __FIFONUMBER__: Receive FIFO number, CAN_FIFO0 or CAN_FIFO1. |
| * @retval The number of pending message. |
| */ |
| #define __HAL_CAN_MSG_PENDING(__HANDLE__, __FIFONUMBER__) (((__FIFONUMBER__) == CAN_FIFO0)? \ |
| ((uint8_t)((__HANDLE__)->Instance->RF0R&(uint32_t)0x03)) : ((uint8_t)((__HANDLE__)->Instance->RF1R&(uint32_t)0x03))) |
| |
| /** @brief Check whether the specified CAN flag is set or not. |
| * @param __HANDLE__: specifies the CAN Handle. |
| * @param __FLAG__: specifies the flag to check. |
| * This parameter can be one of the following values: |
| * @arg CAN_TSR_RQCP0: Request MailBox0 Flag |
| * @arg CAN_TSR_RQCP1: Request MailBox1 Flag |
| * @arg CAN_TSR_RQCP2: Request MailBox2 Flag |
| * @arg CAN_FLAG_TXOK0: Transmission OK MailBox0 Flag |
| * @arg CAN_FLAG_TXOK1: Transmission OK MailBox1 Flag |
| * @arg CAN_FLAG_TXOK2: Transmission OK MailBox2 Flag |
| * @arg CAN_FLAG_TME0: Transmit mailbox 0 empty Flag |
| * @arg CAN_FLAG_TME1: Transmit mailbox 1 empty Flag |
| * @arg CAN_FLAG_TME2: Transmit mailbox 2 empty Flag |
| * @arg CAN_FLAG_FMP0: FIFO 0 Message Pending Flag |
| * @arg CAN_FLAG_FF0: FIFO 0 Full Flag |
| * @arg CAN_FLAG_FOV0: FIFO 0 Overrun Flag |
| * @arg CAN_FLAG_FMP1: FIFO 1 Message Pending Flag |
| * @arg CAN_FLAG_FF1: FIFO 1 Full Flag |
| * @arg CAN_FLAG_FOV1: FIFO 1 Overrun Flag |
| * @arg CAN_FLAG_WKU: Wake up Flag |
| * @arg CAN_FLAG_SLAK: Sleep acknowledge Flag |
| * @arg CAN_FLAG_SLAKI: Sleep acknowledge Flag |
| * @arg CAN_FLAG_EWG: Error Warning Flag |
| * @arg CAN_FLAG_EPV: Error Passive Flag |
| * @arg CAN_FLAG_BOF: Bus-Off Flag |
| * @retval The new state of __FLAG__ (TRUE or FALSE). |
| */ |
| #define __HAL_CAN_GET_FLAG(__HANDLE__, __FLAG__) \ |
| ((((__FLAG__) >> 8) == 5)? ((((__HANDLE__)->Instance->TSR) & (1U << ((__FLAG__) & CAN_FLAG_MASK))) == (1U << ((__FLAG__) & CAN_FLAG_MASK))): \ |
| (((__FLAG__) >> 8) == 2)? ((((__HANDLE__)->Instance->RF0R) & (1U << ((__FLAG__) & CAN_FLAG_MASK))) == (1U << ((__FLAG__) & CAN_FLAG_MASK))): \ |
| (((__FLAG__) >> 8) == 4)? ((((__HANDLE__)->Instance->RF1R) & (1U << ((__FLAG__) & CAN_FLAG_MASK))) == (1U << ((__FLAG__) & CAN_FLAG_MASK))): \ |
| (((__FLAG__) >> 8) == 1)? ((((__HANDLE__)->Instance->MSR) & (1U << ((__FLAG__) & CAN_FLAG_MASK))) == (1U << ((__FLAG__) & CAN_FLAG_MASK))): \ |
| ((((__HANDLE__)->Instance->ESR) & (1U << ((__FLAG__) & CAN_FLAG_MASK))) == (1U << ((__FLAG__) & CAN_FLAG_MASK)))) |
| |
| /** @brief Clear the specified CAN pending flag. |
| * @param __HANDLE__: specifies the CAN Handle. |
| * @param __FLAG__: specifies the flag to check. |
| * This parameter can be one of the following values: |
| * @arg CAN_TSR_RQCP0: Request MailBox0 Flag |
| * @arg CAN_TSR_RQCP1: Request MailBox1 Flag |
| * @arg CAN_TSR_RQCP2: Request MailBox2 Flag |
| * @arg CAN_FLAG_TXOK0: Transmission OK MailBox0 Flag |
| * @arg CAN_FLAG_TXOK1: Transmission OK MailBox1 Flag |
| * @arg CAN_FLAG_TXOK2: Transmission OK MailBox2 Flag |
| * @arg CAN_FLAG_TME0: Transmit mailbox 0 empty Flag |
| * @arg CAN_FLAG_TME1: Transmit mailbox 1 empty Flag |
| * @arg CAN_FLAG_TME2: Transmit mailbox 2 empty Flag |
| * @arg CAN_FLAG_FMP0: FIFO 0 Message Pending Flag |
| * @arg CAN_FLAG_FF0: FIFO 0 Full Flag |
| * @arg CAN_FLAG_FOV0: FIFO 0 Overrun Flag |
| * @arg CAN_FLAG_FMP1: FIFO 1 Message Pending Flag |
| * @arg CAN_FLAG_FF1: FIFO 1 Full Flag |
| * @arg CAN_FLAG_FOV1: FIFO 1 Overrun Flag |
| * @arg CAN_FLAG_WKU: Wake up Flag |
| * @arg CAN_FLAG_SLAKI: Sleep acknowledge Flag |
| * @retval The new state of __FLAG__ (TRUE or FALSE). |
| */ |
| #define __HAL_CAN_CLEAR_FLAG(__HANDLE__, __FLAG__) \ |
| ((((__FLAG__) >> 8U) == 5)? (((__HANDLE__)->Instance->TSR) = (1U << ((__FLAG__) & CAN_FLAG_MASK))): \ |
| (((__FLAG__) >> 8U) == 2)? (((__HANDLE__)->Instance->RF0R) = (1U << ((__FLAG__) & CAN_FLAG_MASK))): \ |
| (((__FLAG__) >> 8U) == 4)? (((__HANDLE__)->Instance->RF1R) = (1U << ((__FLAG__) & CAN_FLAG_MASK))): \ |
| (((__FLAG__) >> 8U) == 1)? (((__HANDLE__)->Instance->MSR) = (1U << ((__FLAG__) & CAN_FLAG_MASK))): 0) |
| |
| |
| /** @brief Check whether the specified CAN interrupt source is enabled or not. |
| * @param __HANDLE__: specifies the CAN Handle. |
| * @param __INTERRUPT__: specifies the CAN interrupt source to check. |
| * This parameter can be one of the following values: |
| * @arg CAN_IT_TME: Transmit mailbox empty interrupt enable |
| * @arg CAN_IT_FMP0: FIFO0 message pending interrupt enable |
| * @arg CAN_IT_FMP1: FIFO1 message pending interrupt enable |
| * @retval The new state of __IT__ (TRUE or FALSE). |
| */ |
| #define __HAL_CAN_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) ((((__HANDLE__)->Instance->IER & (__INTERRUPT__)) == (__INTERRUPT__)) ? SET : RESET) |
| |
| /** |
| * @brief Check the transmission status of a CAN Frame. |
| * @param __HANDLE__: specifies the CAN Handle. |
| * @param __TRANSMITMAILBOX__: the number of the mailbox that is used for transmission. |
| * @retval The new status of transmission (TRUE or FALSE). |
| */ |
| #define __HAL_CAN_TRANSMIT_STATUS(__HANDLE__, __TRANSMITMAILBOX__)\ |
| (((__TRANSMITMAILBOX__) == CAN_TXMAILBOX_0)? ((((__HANDLE__)->Instance->TSR) & (CAN_TSR_RQCP0 | CAN_TSR_TXOK0 | CAN_TSR_TME0)) == (CAN_TSR_RQCP0 | CAN_TSR_TXOK0 | CAN_TSR_TME0)) :\ |
| ((__TRANSMITMAILBOX__) == CAN_TXMAILBOX_1)? ((((__HANDLE__)->Instance->TSR) & (CAN_TSR_RQCP1 | CAN_TSR_TXOK1 | CAN_TSR_TME1)) == (CAN_TSR_RQCP1 | CAN_TSR_TXOK1 | CAN_TSR_TME1)) :\ |
| ((((__HANDLE__)->Instance->TSR) & (CAN_TSR_RQCP2 | CAN_TSR_TXOK2 | CAN_TSR_TME2)) == (CAN_TSR_RQCP2 | CAN_TSR_TXOK2 | CAN_TSR_TME2))) |
| |
| |
| |
| /** |
| * @brief Release the specified receive FIFO. |
| * @param __HANDLE__: CAN handle. |
| * @param __FIFONUMBER__: Receive FIFO number, CAN_FIFO0 or CAN_FIFO1. |
| * @retval None |
| */ |
| #define __HAL_CAN_FIFO_RELEASE(__HANDLE__, __FIFONUMBER__) (((__FIFONUMBER__) == CAN_FIFO0)? \ |
| ((__HANDLE__)->Instance->RF0R |= CAN_RF0R_RFOM0) : ((__HANDLE__)->Instance->RF1R |= CAN_RF1R_RFOM1)) |
| |
| /** |
| * @brief Cancel a transmit request. |
| * @param __HANDLE__: specifies the CAN Handle. |
| * @param __TRANSMITMAILBOX__: the number of the mailbox that is used for transmission. |
| * @retval None |
| */ |
| #define __HAL_CAN_CANCEL_TRANSMIT(__HANDLE__, __TRANSMITMAILBOX__)\ |
| (((__TRANSMITMAILBOX__) == CAN_TXMAILBOX_0)? ((__HANDLE__)->Instance->TSR |= CAN_TSR_ABRQ0) :\ |
| ((__TRANSMITMAILBOX__) == CAN_TXMAILBOX_1)? ((__HANDLE__)->Instance->TSR |= CAN_TSR_ABRQ1) :\ |
| ((__HANDLE__)->Instance->TSR |= CAN_TSR_ABRQ2)) |
| |
| /** |
| * @brief Enable or disable the DBG Freeze for CAN. |
| * @param __HANDLE__: specifies the CAN Handle. |
| * @param __NEWSTATE__: new state of the CAN peripheral. |
| * This parameter can be: ENABLE (CAN reception/transmission is frozen |
| * during debug. Reception FIFO can still be accessed/controlled normally) |
| * or DISABLE (CAN is working during debug). |
| * @retval None |
| */ |
| #define __HAL_CAN_DBG_FREEZE(__HANDLE__, __NEWSTATE__) (((__NEWSTATE__) == ENABLE)? \ |
| ((__HANDLE__)->Instance->MCR |= CAN_MCR_DBF) : ((__HANDLE__)->Instance->MCR &= ~CAN_MCR_DBF)) |
| |
| /** |
| * @} |
| */ |
| |
| /* Exported functions --------------------------------------------------------*/ |
| /** @addtogroup CAN_Exported_Functions CAN Exported Functions |
| * @{ |
| */ |
| |
| /** @defgroup CAN_Exported_Functions_Group1 Initialization and de-initialization functions |
| * @brief Initialization and Configuration functions |
| * @{ |
| */ |
| /* addtogroup and de-initialization functions *****************************/ |
| HAL_StatusTypeDef HAL_CAN_Init(CAN_HandleTypeDef* hcan); |
| HAL_StatusTypeDef HAL_CAN_ConfigFilter(CAN_HandleTypeDef* hcan, CAN_FilterConfTypeDef* sFilterConfig); |
| HAL_StatusTypeDef HAL_CAN_DeInit(CAN_HandleTypeDef* hcan); |
| void HAL_CAN_MspInit(CAN_HandleTypeDef* hcan); |
| void HAL_CAN_MspDeInit(CAN_HandleTypeDef* hcan); |
| /** |
| * @} |
| */ |
| |
| /** @addtogroup CAN_Exported_Functions_Group2 Input and Output operation functions |
| * @brief I/O operation functions |
| * @{ |
| */ |
| /* IO operation functions *****************************************************/ |
| HAL_StatusTypeDef HAL_CAN_Transmit(CAN_HandleTypeDef *hcan, uint32_t Timeout); |
| HAL_StatusTypeDef HAL_CAN_Transmit_IT(CAN_HandleTypeDef *hcan); |
| HAL_StatusTypeDef HAL_CAN_Receive(CAN_HandleTypeDef *hcan, uint8_t FIFONumber, uint32_t Timeout); |
| HAL_StatusTypeDef HAL_CAN_Receive_IT(CAN_HandleTypeDef *hcan, uint8_t FIFONumber); |
| HAL_StatusTypeDef HAL_CAN_Sleep(CAN_HandleTypeDef *hcan); |
| HAL_StatusTypeDef HAL_CAN_WakeUp(CAN_HandleTypeDef *hcan); |
| void HAL_CAN_IRQHandler(CAN_HandleTypeDef* hcan); |
| void HAL_CAN_TxCpltCallback(CAN_HandleTypeDef* hcan); |
| void HAL_CAN_RxCpltCallback(CAN_HandleTypeDef* hcan); |
| void HAL_CAN_ErrorCallback(CAN_HandleTypeDef *hcan); |
| /** |
| * @} |
| */ |
| |
| /** @addtogroup CAN_Exported_Functions_Group3 Peripheral State and Error functions |
| * @brief CAN Peripheral State functions |
| * @{ |
| */ |
| /* Peripheral State and Error functions ***************************************/ |
| uint32_t HAL_CAN_GetError(CAN_HandleTypeDef *hcan); |
| HAL_CAN_StateTypeDef HAL_CAN_GetState(CAN_HandleTypeDef* hcan); |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Private types -------------------------------------------------------------*/ |
| /* Private constants ---------------------------------------------------------*/ |
| /** @defgroup CAN_Private_Constants CAN Private Constants |
| * @{ |
| */ |
| /** @defgroup CAN_transmit_constants CAN Transmit Constants |
| * @{ |
| */ |
| #define CAN_TXSTATUS_NOMAILBOX ((uint8_t)0x04) /*!< CAN cell did not provide CAN_TxStatus_NoMailBox */ |
| /** |
| * @} |
| */ |
| #define CAN_FLAG_MASK ((uint32_t)0x000000FF) |
| |
| |
| /** |
| * @} |
| */ |
| |
| /* Private macros ------------------------------------------------------------*/ |
| /** @defgroup CAN_Private_Macros CAN Private Macros |
| * @{ |
| */ |
| |
| #define IS_CAN_MODE(MODE) (((MODE) == CAN_MODE_NORMAL) || \ |
| ((MODE) == CAN_MODE_LOOPBACK)|| \ |
| ((MODE) == CAN_MODE_SILENT) || \ |
| ((MODE) == CAN_MODE_SILENT_LOOPBACK)) |
| |
| #define IS_CAN_SJW(SJW) (((SJW) == CAN_SJW_1TQ) || ((SJW) == CAN_SJW_2TQ)|| \ |
| ((SJW) == CAN_SJW_3TQ) || ((SJW) == CAN_SJW_4TQ)) |
| |
| #define IS_CAN_BS1(BS1) ((BS1) <= CAN_BS1_16TQ) |
| |
| #define IS_CAN_BS2(BS2) ((BS2) <= CAN_BS2_8TQ) |
| |
| #define IS_CAN_PRESCALER(PRESCALER) (((PRESCALER) >= 1) && ((PRESCALER) <= 1024)) |
| |
| #define IS_CAN_FILTER_NUMBER(NUMBER) ((NUMBER) <= 27) |
| |
| #define IS_CAN_FILTER_MODE(MODE) (((MODE) == CAN_FILTERMODE_IDMASK) || \ |
| ((MODE) == CAN_FILTERMODE_IDLIST)) |
| |
| #define IS_CAN_FILTER_SCALE(SCALE) (((SCALE) == CAN_FILTERSCALE_16BIT) || \ |
| ((SCALE) == CAN_FILTERSCALE_32BIT)) |
| |
| #define IS_CAN_FILTER_FIFO(FIFO) (((FIFO) == CAN_FILTER_FIFO0) || \ |
| ((FIFO) == CAN_FILTER_FIFO1)) |
| |
| #define IS_CAN_BANKNUMBER(BANKNUMBER) ((BANKNUMBER) <= 28) |
| |
| #define IS_CAN_TRANSMITMAILBOX(TRANSMITMAILBOX) ((TRANSMITMAILBOX) <= ((uint8_t)0x02)) |
| |
| #define IS_CAN_STDID(STDID) ((STDID) <= ((uint32_t)0x7FF)) |
| |
| #define IS_CAN_EXTID(EXTID) ((EXTID) <= ((uint32_t)0x1FFFFFFF)) |
| |
| #define IS_CAN_DLC(DLC) ((DLC) <= ((uint8_t)0x08)) |
| |
| #define IS_CAN_IDTYPE(IDTYPE) (((IDTYPE) == CAN_ID_STD) || \ |
| ((IDTYPE) == CAN_ID_EXT)) |
| |
| #define IS_CAN_RTR(RTR) (((RTR) == CAN_RTR_DATA) || ((RTR) == CAN_RTR_REMOTE)) |
| |
| #define IS_CAN_FIFO(FIFO) (((FIFO) == CAN_FIFO0) || ((FIFO) == CAN_FIFO1)) |
| |
| /** |
| * @} |
| */ |
| |
| /* Private functions ---------------------------------------------------------*/ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| #endif /* CAN1 */ |
| |
| #ifdef __cplusplus |
| } |
| #endif |
| |
| #endif /* __STM32L4xx_HAL_CAN_LEGACY_H */ |
| |
| |
| /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |