blob: 74be0cabc49348f67d96976dcf863545fdd68200 [file] [log] [blame]
/**
******************************************************************************
* @file stm32l5xx_hal_gpio.h
* @author MCD Application Team
* @brief Header file of GPIO HAL module.
******************************************************************************
* @attention
*
* Copyright (c) 2019 STMicroelectronics.
* All rights reserved.
*
* This software is licensed under terms that can be found in the LICENSE file
* in the root directory of this software component.
* If no LICENSE file comes with this software, it is provided AS-IS.
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef STM32L5xx_HAL_GPIO_H
#define STM32L5xx_HAL_GPIO_H
#ifdef __cplusplus
extern "C" {
#endif
/* Includes ------------------------------------------------------------------*/
#include "stm32l5xx_hal_def.h"
/** @addtogroup STM32L5xx_HAL_Driver
* @{
*/
/** @defgroup GPIO GPIO
* @brief GPIO HAL module driver
* @{
*/
/* Exported types ------------------------------------------------------------*/
/** @defgroup GPIO_Exported_Types GPIO Exported Types
* @{
*/
/**
* @brief GPIO Init structure definition
*/
typedef struct
{
uint32_t Pin; /*!< Specifies the GPIO pins to be configured.
This parameter can be any value of @ref GPIO_pins */
uint32_t Mode; /*!< Specifies the operating mode for the selected pins.
This parameter can be a value of @ref GPIO_mode */
uint32_t Pull; /*!< Specifies the Pull-up or Pull-Down activation for the selected pins.
This parameter can be a value of @ref GPIO_pull */
uint32_t Speed; /*!< Specifies the speed for the selected pins.
This parameter can be a value of @ref GPIO_speed */
uint32_t Alternate; /*!< Peripheral to be connected to the selected pins
This parameter can be a value of @ref GPIOEx_Alternate_function_selection */
} GPIO_InitTypeDef;
/**
* @brief GPIO Bit SET and Bit RESET enumeration
*/
typedef enum
{
GPIO_PIN_RESET = 0U,
GPIO_PIN_SET
} GPIO_PinState;
/**
* @}
*/
/* Exported constants --------------------------------------------------------*/
/** @defgroup GPIO_Exported_Constants GPIO Exported Constants
* @{
*/
/** @defgroup GPIO_pins GPIO pins
* @{
*/
#define GPIO_PIN_0 ((uint16_t)0x0001) /* Pin 0 selected */
#define GPIO_PIN_1 ((uint16_t)0x0002) /* Pin 1 selected */
#define GPIO_PIN_2 ((uint16_t)0x0004) /* Pin 2 selected */
#define GPIO_PIN_3 ((uint16_t)0x0008) /* Pin 3 selected */
#define GPIO_PIN_4 ((uint16_t)0x0010) /* Pin 4 selected */
#define GPIO_PIN_5 ((uint16_t)0x0020) /* Pin 5 selected */
#define GPIO_PIN_6 ((uint16_t)0x0040) /* Pin 6 selected */
#define GPIO_PIN_7 ((uint16_t)0x0080) /* Pin 7 selected */
#define GPIO_PIN_8 ((uint16_t)0x0100) /* Pin 8 selected */
#define GPIO_PIN_9 ((uint16_t)0x0200) /* Pin 9 selected */
#define GPIO_PIN_10 ((uint16_t)0x0400) /* Pin 10 selected */
#define GPIO_PIN_11 ((uint16_t)0x0800) /* Pin 11 selected */
#define GPIO_PIN_12 ((uint16_t)0x1000) /* Pin 12 selected */
#define GPIO_PIN_13 ((uint16_t)0x2000) /* Pin 13 selected */
#define GPIO_PIN_14 ((uint16_t)0x4000) /* Pin 14 selected */
#define GPIO_PIN_15 ((uint16_t)0x8000) /* Pin 15 selected */
#define GPIO_PIN_All ((uint16_t)0xFFFF) /* All pins selected */
#define GPIO_PIN_MASK (0x0000FFFFU) /* PIN mask for assert test */
/**
* @}
*/
/** @defgroup GPIO_mode GPIO mode
* @brief GPIO Configuration Mode
* Elements values convention: 0x00WX00YZ
* - W : EXTI trigger detection on 3 bits
* - X : EXTI mode (IT or Event) on 2 bits
* - Y : Output type (Push Pull or Open Drain) on 1 bit
* - Z : GPIO mode (Input, Output, Alternate or Analog) on 2 bits
* @{
*/
#define GPIO_MODE_INPUT MODE_INPUT /*!< Input Floating Mode */
#define GPIO_MODE_OUTPUT_PP (MODE_OUTPUT | OUTPUT_PP) /*!< Output Push Pull Mode */
#define GPIO_MODE_OUTPUT_OD (MODE_OUTPUT | OUTPUT_OD) /*!< Output Open Drain Mode */
#define GPIO_MODE_AF_PP (MODE_AF | OUTPUT_PP) /*!< Alternate Function Push Pull Mode */
#define GPIO_MODE_AF_OD (MODE_AF | OUTPUT_OD) /*!< Alternate Function Open Drain Mode */
#define GPIO_MODE_ANALOG MODE_ANALOG /*!< Analog Mode */
#define GPIO_MODE_IT_RISING (MODE_INPUT | EXTI_IT | TRIGGER_RISING) /*!< External Interrupt Mode with Rising edge trigger detection */
#define GPIO_MODE_IT_FALLING (MODE_INPUT | EXTI_IT | TRIGGER_FALLING) /*!< External Interrupt Mode with Falling edge trigger detection */
#define GPIO_MODE_IT_RISING_FALLING (MODE_INPUT | EXTI_IT | TRIGGER_RISING | TRIGGER_FALLING) /*!< External Interrupt Mode with Rising/Falling edge trigger detection */
#define GPIO_MODE_EVT_RISING (MODE_INPUT | EXTI_EVT | TRIGGER_RISING) /*!< External Event Mode with Rising edge trigger detection */
#define GPIO_MODE_EVT_FALLING (MODE_INPUT | EXTI_EVT | TRIGGER_FALLING) /*!< External Event Mode with Falling edge trigger detection */
#define GPIO_MODE_EVT_RISING_FALLING (MODE_INPUT | EXTI_EVT | TRIGGER_RISING | TRIGGER_FALLING) /*!< External Event Mode with Rising/Falling edge trigger detection */
/**
* @}
*/
/** @defgroup GPIO_speed GPIO speed
* @brief GPIO Output Maximum frequency
* @{
*/
#define GPIO_SPEED_FREQ_LOW 0x00000000u /*!< Low speed */
#define GPIO_SPEED_FREQ_MEDIUM 0x00000001u /*!< Medium speed */
#define GPIO_SPEED_FREQ_HIGH 0x00000002u /*!< High speed */
#define GPIO_SPEED_FREQ_VERY_HIGH 0x00000003u /*!< Very high speed */
/**
* @}
*/
/** @defgroup GPIO_pull GPIO pull
* @brief GPIO Pull-Up or Pull-Down Activation
* @{
*/
#define GPIO_NOPULL 0x00000000u /*!< No Pull-up or Pull-down activation */
#define GPIO_PULLUP 0x00000001u /*!< Pull-up activation */
#define GPIO_PULLDOWN 0x00000002u /*!< Pull-down activation */
/**
* @}
*/
#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U)
/** @defgroup GPIO_attributes GPIO attributes
* @brief GPIO pin secure or non-secure attributes
* @{
*/
#define GPIO_PIN_SEC (0x00000001U) /*!< Secure pin attribute */
#define GPIO_PIN_NSEC (0x00000000U) /*!< Non-secure pin attribute */
/**
* @}
*/
#endif /* __ARM_FEATURE_CMSE */
/**
* @}
*/
/* Exported macro ------------------------------------------------------------*/
/** @defgroup GPIO_Exported_Macros GPIO Exported Macros
* @{
*/
/**
* @brief Check whether the specified EXTI line is rising edge asserted or not.
* @param __EXTI_LINE__ specifies the EXTI line to check.
* This parameter can be GPIO_PIN_x where x can be(0..15)
* @retval The new state of __EXTI_LINE__ (SET or RESET).
*/
#define __HAL_GPIO_EXTI_GET_RISING_IT(__EXTI_LINE__) (EXTI->RPR1 & (__EXTI_LINE__))
/**
* @brief Clear the EXTI line rising pending bits.
* @param __EXTI_LINE__ specifies the EXTI lines to clear.
* This parameter can be any combination of GPIO_PIN_x where x can be (0..15)
* @retval None
*/
#define __HAL_GPIO_EXTI_CLEAR_RISING_IT(__EXTI_LINE__) (EXTI->RPR1 = (__EXTI_LINE__))
/**
* @brief Check whether the specified EXTI line is falling edge asserted or not.
* @param __EXTI_LINE__ specifies the EXTI line to check.
* This parameter can be GPIO_PIN_x where x can be(0..15)
* @retval The new state of __EXTI_LINE__ (SET or RESET).
*/
#define __HAL_GPIO_EXTI_GET_FALLING_IT(__EXTI_LINE__) (EXTI->FPR1 & (__EXTI_LINE__))
/**
* @brief Clear the EXTI line falling pending bits.
* @param __EXTI_LINE__ specifies the EXTI lines to clear.
* This parameter can be any combination of GPIO_PIN_x where x can be (0..15)
* @retval None
*/
#define __HAL_GPIO_EXTI_CLEAR_FALLING_IT(__EXTI_LINE__) (EXTI->FPR1 = (__EXTI_LINE__))
/**
* @brief Check whether the specified EXTI line is asserted or not.
* @param __EXTI_LINE__ specifies the EXTI line to check.
* This parameter can be GPIO_PIN_x where x can be(0..15)
* @retval The new state of __EXTI_LINE__ (SET or RESET).
*/
#define __HAL_GPIO_EXTI_GET_IT(__EXTI_LINE__) (__HAL_GPIO_EXTI_GET_RISING_IT(__EXTI_LINE__) || \
__HAL_GPIO_EXTI_GET_FALLING_IT(__EXTI_LINE__))
/**
* @brief Clear the EXTI line pending bits.
* @param __EXTI_LINE__ specifies the EXTI lines to clear.
* This parameter can be any combination of GPIO_PIN_x where x can be (0..15)
* @retval None
*/
#define __HAL_GPIO_EXTI_CLEAR_IT(__EXTI_LINE__) \
do { \
__HAL_GPIO_EXTI_CLEAR_RISING_IT(__EXTI_LINE__); \
__HAL_GPIO_EXTI_CLEAR_FALLING_IT(__EXTI_LINE__); \
} while(0)
/**
* @brief Generate a Software interrupt on selected EXTI line(s).
* @param __EXTI_LINE__ specifies the EXTI line to set.
* This parameter can be any combination of GPIO_PIN_x where x can be (0..15)
* @retval None
*/
#define __HAL_GPIO_EXTI_GENERATE_SWIT(__EXTI_LINE__) (EXTI->SWIER1 = (__EXTI_LINE__))
/**
* @brief Check whether the specified EXTI line flag is set or not.
* @param __EXTI_LINE__ specifies the EXTI line flag to check.
* This parameter can be GPIO_PIN_x where x can be(0..15)
* @retval The new state of __EXTI_LINE__ (SET or RESET).
*/
#define __HAL_GPIO_EXTI_GET_FLAG(__EXTI_LINE__) __HAL_GPIO_EXTI_GET_IT(__EXTI_LINE__)
/**
* @brief Clear the EXTI line pending flags.
* @param __EXTI_LINE__ specifies the EXTI lines flags to clear.
* This parameter can be any combination of GPIO_PIN_x where x can be (0..15)
* @retval None
*/
#define __HAL_GPIO_EXTI_CLEAR_FLAG(__EXTI_LINE__) __HAL_GPIO_EXTI_CLEAR_IT(__EXTI_LINE__)
/**
* @}
*/
/* Private macros ------------------------------------------------------------*/
/** @defgroup GPIO_Private_Constants GPIO Private Constants
* @{
*/
#define GPIO_MODE_Pos 0u
#define GPIO_MODE (0x3uL << GPIO_MODE_Pos)
#define MODE_INPUT (0x0uL << GPIO_MODE_Pos)
#define MODE_OUTPUT (0x1uL << GPIO_MODE_Pos)
#define MODE_AF (0x2uL << GPIO_MODE_Pos)
#define MODE_ANALOG (0x3uL << GPIO_MODE_Pos)
#define OUTPUT_TYPE_Pos 4u
#define OUTPUT_TYPE (0x1uL << OUTPUT_TYPE_Pos)
#define OUTPUT_PP (0x0uL << OUTPUT_TYPE_Pos)
#define OUTPUT_OD (0x1uL << OUTPUT_TYPE_Pos)
#define EXTI_MODE_Pos 16u
#define EXTI_MODE (0x3uL << EXTI_MODE_Pos)
#define EXTI_IT (0x1uL << EXTI_MODE_Pos)
#define EXTI_EVT (0x2uL << EXTI_MODE_Pos)
#define TRIGGER_MODE_Pos 20u
#define TRIGGER_MODE (0x7uL << TRIGGER_MODE_Pos)
#define TRIGGER_RISING (0x1uL << TRIGGER_MODE_Pos)
#define TRIGGER_FALLING (0x2uL << TRIGGER_MODE_Pos)
/**
* @}
*/
/** @defgroup GPIO_Private_Macros GPIO Private Macros
* @{
*/
#define IS_GPIO_PIN_ACTION(ACTION) (((ACTION) == GPIO_PIN_RESET) || ((ACTION) == GPIO_PIN_SET))
#define IS_GPIO_PIN(__PIN__) ((((uint32_t)(__PIN__) & GPIO_PIN_MASK) != 0x00U) &&\
(((uint32_t)(__PIN__) & ~GPIO_PIN_MASK) == 0x00U))
#define IS_GPIO_MODE(__MODE__) (((__MODE__) == GPIO_MODE_INPUT) ||\
((__MODE__) == GPIO_MODE_OUTPUT_PP) ||\
((__MODE__) == GPIO_MODE_OUTPUT_OD) ||\
((__MODE__) == GPIO_MODE_AF_PP) ||\
((__MODE__) == GPIO_MODE_AF_OD) ||\
((__MODE__) == GPIO_MODE_IT_RISING) ||\
((__MODE__) == GPIO_MODE_IT_FALLING) ||\
((__MODE__) == GPIO_MODE_IT_RISING_FALLING) ||\
((__MODE__) == GPIO_MODE_EVT_RISING) ||\
((__MODE__) == GPIO_MODE_EVT_FALLING) ||\
((__MODE__) == GPIO_MODE_EVT_RISING_FALLING) ||\
((__MODE__) == GPIO_MODE_ANALOG))
#define IS_GPIO_SPEED(__SPEED__) (((__SPEED__) == GPIO_SPEED_FREQ_LOW) ||\
((__SPEED__) == GPIO_SPEED_FREQ_MEDIUM) ||\
((__SPEED__) == GPIO_SPEED_FREQ_HIGH) ||\
((__SPEED__) == GPIO_SPEED_FREQ_VERY_HIGH))
#define IS_GPIO_PULL(__PULL__) (((__PULL__) == GPIO_NOPULL) ||\
((__PULL__) == GPIO_PULLUP) || \
((__PULL__) == GPIO_PULLDOWN))
#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U)
#define IS_GPIO_PIN_ATTRIBUTES(__ATTRIBUTES__) (((__ATTRIBUTES__) == GPIO_PIN_SEC) ||\
((__ATTRIBUTES__) == GPIO_PIN_NSEC))
#endif /* __ARM_FEATURE_CMSE */
/**
* @}
*/
/* Include GPIO HAL Extended module */
#include "stm32l5xx_hal_gpio_ex.h"
/* Exported functions --------------------------------------------------------*/
/** @defgroup GPIO_Exported_Functions GPIO Exported Functions
* @brief GPIO Exported Functions
* @{
*/
/** @defgroup GPIO_Exported_Functions_Group1 Initialization/de-initialization functions
* @brief Initialization and Configuration functions
* @{
*/
/* Initialization and de-initialization functions *****************************/
void HAL_GPIO_Init(GPIO_TypeDef *GPIOx, GPIO_InitTypeDef *GPIO_Init);
void HAL_GPIO_DeInit(GPIO_TypeDef *GPIOx, uint32_t GPIO_Pin);
/**
* @}
*/
/** @defgroup GPIO_Exported_Functions_Group2 IO operation functions
* @brief IO operation functions
* @{
*/
/* IO operation functions *****************************************************/
GPIO_PinState HAL_GPIO_ReadPin(GPIO_TypeDef *GPIOx, uint16_t GPIO_Pin);
void HAL_GPIO_WritePin(GPIO_TypeDef *GPIOx, uint16_t GPIO_Pin, GPIO_PinState PinState);
void HAL_GPIO_TogglePin(GPIO_TypeDef *GPIOx, uint16_t GPIO_Pin);
HAL_StatusTypeDef HAL_GPIO_LockPin(GPIO_TypeDef *GPIOx, uint16_t GPIO_Pin);
void HAL_GPIO_EXTI_IRQHandler(uint16_t GPIO_Pin);
void HAL_GPIO_EXTI_Rising_Callback(uint16_t GPIO_Pin);
void HAL_GPIO_EXTI_Falling_Callback(uint16_t GPIO_Pin);
/**
* @}
*/
#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U)
/** @defgroup GPIO_Exported_Functions_Group3 IO attributes management functions
* @{
*/
/* IO attributes management functions *****************************************/
void HAL_GPIO_ConfigPinAttributes(GPIO_TypeDef *GPIOx, uint16_t GPIO_Pin, uint32_t PinAttributes);
HAL_StatusTypeDef HAL_GPIO_GetConfigPinAttributes(GPIO_TypeDef *GPIOx, uint16_t GPIO_Pin, uint32_t *pPinAttributes);
/**
* @}
*/
#endif /* __ARM_FEATURE_CMSE */
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
#ifdef __cplusplus
}
#endif
#endif /* STM32L5xx_HAL_GPIO_H */