| /** |
| ****************************************************************************** |
| * @file stm32wbxx_hal_flash.h |
| * @author MCD Application Team |
| * @brief Header file of FLASH HAL module. |
| ****************************************************************************** |
| * @attention |
| * |
| * <h2><center>© Copyright (c) 2019 STMicroelectronics. |
| * All rights reserved.</center></h2> |
| * |
| * This software component is licensed by ST under BSD 3-Clause license, |
| * the "License"; You may not use this file except in compliance with the |
| * License. You may obtain a copy of the License at: |
| * opensource.org/licenses/BSD-3-Clause |
| * |
| ****************************************************************************** |
| */ |
| |
| /* Define to prevent recursive inclusion -------------------------------------*/ |
| #ifndef STM32WBxx_HAL_FLASH_H |
| #define STM32WBxx_HAL_FLASH_H |
| |
| #ifdef __cplusplus |
| extern "C" { |
| #endif |
| |
| /* Includes ------------------------------------------------------------------*/ |
| #include "stm32wbxx_hal_def.h" |
| |
| /** @addtogroup STM32WBxx_HAL_Driver |
| * @{ |
| */ |
| |
| /** @addtogroup FLASH |
| * @{ |
| */ |
| |
| /* Exported types ------------------------------------------------------------*/ |
| /** @defgroup FLASH_Exported_Types FLASH Exported Types |
| * @{ |
| */ |
| |
| /** |
| * @brief FLASH Erase structure definition |
| */ |
| typedef struct |
| { |
| uint32_t TypeErase; /*!< Page erase. |
| This parameter can be a value of @ref FLASH_TYPE_ERASE */ |
| uint32_t Page; /*!< Initial Flash page to erase when page erase is enabled |
| This parameter must be a value between 0 and (FLASH_PAGE_NB - 1) */ |
| uint32_t NbPages; /*!< Number of pages to be erased. |
| This parameter must be a value between 1 and (FLASH_PAGE_NB - value of initial page)*/ |
| } FLASH_EraseInitTypeDef; |
| |
| /** |
| * @brief FLASH Option Bytes Program structure definition |
| */ |
| typedef struct |
| { |
| uint32_t OptionType; /*!< Option byte to be configured. |
| This parameter can be a combination of the values of @ref FLASH_OB_TYPE */ |
| uint32_t WRPArea; /*!< Write protection area to be programmed (used for OPTIONBYTE_WRP). |
| Only one WRP area could be programmed at the same time. |
| This parameter can be value of @ref FLASH_OB_WRP_AREA */ |
| uint32_t WRPStartOffset; /*!< Write protection start offset (used for OPTIONBYTE_WRP). |
| This parameter must be a value between 0 and (max number of pages - 1) */ |
| uint32_t WRPEndOffset; /*!< Write protection end offset (used for OPTIONBYTE_WRP). |
| This parameter must be a value between WRPStartOffset and (max number of pages - 1) */ |
| uint32_t RDPLevel; /*!< Set the read protection level (used for OPTIONBYTE_RDP). |
| This parameter can be a value of @ref FLASH_OB_READ_PROTECTION */ |
| uint32_t UserType; /*!< User option byte(s) to be configured (used for OPTIONBYTE_USER). |
| This parameter can be a combination of @ref FLASH_OB_USER_TYPE */ |
| uint32_t UserConfig; /*!< Value of the user option byte (used for OPTIONBYTE_USER). |
| This parameter can be a combination of the values of |
| @ref FLASH_OB_USER_AGC_TRIM, @ref FLASH_OB_USER_BOR_LEVEL |
| @ref FLASH_OB_USER_nRST_STOP, @ref FLASH_OB_USER_nRST_STANDBY, |
| @ref FLASH_OB_USER_nRST_SHUTDOWN, @ref FLASH_OB_USER_IWDG_SW, |
| @ref FLASH_OB_USER_IWDG_STOP, @ref FLASH_OB_USER_IWDG_STANDBY, |
| @ref FLASH_OB_USER_WWDG_SW, @ref FLASH_OB_USER_nBOOT1, |
| @ref FLASH_OB_USER_SRAM2PE, @ref FLASH_OB_USER_SRAM2RST, |
| @ref FLASH_OB_USER_nSWBOOT0, @ref FLASH_OB_USER_nBOOT0 */ |
| uint32_t PCROPConfig; /*!< Configuration of the PCROP (used for OPTIONBYTE_PCROP). |
| This parameter must be a combination of values of @ref FLASH_OB_PCROP_ZONE |
| and @ref FLASH_OB_PCROP_RDP */ |
| uint32_t PCROP1AStartAddr; /*!< PCROP Zone A Start address (used for OPTIONBYTE_PCROP). It represents first address of start block |
| to protect. Make sure this parameter is multiple of PCROP granularity */ |
| uint32_t PCROP1AEndAddr; /*!< PCROP Zone A End address (used for OPTIONBYTE_PCROP). It represents first address of end block |
| to protect. Make sure this parameter is multiple of PCROP granularity */ |
| uint32_t PCROP1BStartAddr; /*!< PCROP Zone B Start address (used for OPTIONBYTE_PCROP). It represents first address of start block |
| to protect. Make sure this parameter is multiple of PCROP granularity */ |
| uint32_t PCROP1BEndAddr; /*!< PCROP Zone B End address (used for OPTIONBYTE_PCROP). It represents first address of end block |
| to protect. Make sure this parameter is multiple of PCROP granularity */ |
| uint32_t SecureFlashStartAddr; /*!< Secure Flash start address (used for OPTIONBYTE_SECURE_MODE). |
| This parameter must be a value between begin and end of Flash bank |
| => Contains the start address of the first 4kB page of the secure Flash area */ |
| uint32_t SecureRAM2aStartAddr; /*!< Secure Backup RAM2a start address (used for OPTIONBYTE_SECURE_MODE). |
| This parameter can be a value of @ref FLASH_SRAM2A_ADDRESS_RANGE */ |
| uint32_t SecureRAM2bStartAddr; /*!< Secure non-Backup RAM2b start address (used for OPTIONBYTE_SECURE_MODE) |
| This parameter can be a value of @ref FLASH_SRAM2B_ADDRESS_RANGE */ |
| uint32_t SecureMode; /*!< Secure mode activated or desactivated. |
| This parameter can be a value of @ref FLASH_OB_SECURITY_MODE */ |
| uint32_t C2BootRegion; /*!< CPU2 Secure Boot memory region(used for OPTIONBYTE_C2_BOOT_VECT). |
| This parameter can be a value of @ref C2_FLASH_OB_BOOT_REGION */ |
| uint32_t C2SecureBootVectAddr; /*!< CPU2 Secure Boot reset vector (used for OPTIONBYTE_C2_BOOT_VECT). |
| This parameter contains the CPU2 boot reset start address within |
| the selected memory region. Make sure this parameter is word aligned. */ |
| uint32_t IPCCdataBufAddr; /*!< IPCC mailbox data buffer base address (used for OPTIONBYTE_IPCC_BUF_ADDR). |
| This parameter contains the IPCC mailbox data buffer start address area in SRAM2. |
| Make sure this parameter is double-word aligned. */ |
| } FLASH_OBProgramInitTypeDef; |
| |
| /** |
| * @brief FLASH handle Structure definition |
| */ |
| typedef struct |
| { |
| HAL_LockTypeDef Lock; /* FLASH locking object */ |
| uint32_t ErrorCode; /* FLASH error code */ |
| uint32_t ProcedureOnGoing; /* Internal variable to indicate which procedure is ongoing or not in IT context */ |
| uint32_t Address; /* Internal variable to save address selected for program in IT context */ |
| uint32_t Page; /* Internal variable to define the current page which is erasing in IT context */ |
| uint32_t NbPagesToErase; /* Internal variable to save the remaining pages to erase in IT context */ |
| } FLASH_ProcessTypeDef; |
| |
| /** |
| * @} |
| */ |
| |
| /* Exported constants --------------------------------------------------------*/ |
| /** @defgroup FLASH_Exported_Constants FLASH Exported Constants |
| * @{ |
| */ |
| |
| /** @defgroup FLASH_KEYS FLASH Keys |
| * @{ |
| */ |
| #define FLASH_KEY1 0x45670123U /*!< Flash key1 */ |
| #define FLASH_KEY2 0xCDEF89ABU /*!< Flash key2: used with FLASH_KEY1 |
| to unlock the FLASH registers access */ |
| |
| #define FLASH_OPTKEY1 0x08192A3BU /*!< Flash option byte key1 */ |
| #define FLASH_OPTKEY2 0x4C5D6E7FU /*!< Flash option byte key2: used with FLASH_OPTKEY1 |
| to allow option bytes operations */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup FLASH_LATENCY FLASH Latency |
| * @{ |
| */ |
| #define FLASH_LATENCY_0 FLASH_ACR_LATENCY_0WS /*!< FLASH Zero wait state */ |
| #define FLASH_LATENCY_1 FLASH_ACR_LATENCY_1WS /*!< FLASH One wait state */ |
| #define FLASH_LATENCY_2 FLASH_ACR_LATENCY_2WS /*!< FLASH Two wait states */ |
| #define FLASH_LATENCY_3 FLASH_ACR_LATENCY_3WS /*!< FLASH Three wait states */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup FLASH_FLAGS FLASH Flags Definition |
| * @{ |
| */ |
| #define FLASH_FLAG_EOP FLASH_SR_EOP /*!< FLASH End of operation flag */ |
| #define FLASH_FLAG_OPERR FLASH_SR_OPERR /*!< FLASH Operation error flag */ |
| #define FLASH_FLAG_PROGERR FLASH_SR_PROGERR /*!< FLASH Programming error flag */ |
| #define FLASH_FLAG_WRPERR FLASH_SR_WRPERR /*!< FLASH Write protection error flag */ |
| #define FLASH_FLAG_PGAERR FLASH_SR_PGAERR /*!< FLASH Programming alignment error flag */ |
| #define FLASH_FLAG_SIZERR FLASH_SR_SIZERR /*!< FLASH Size error flag */ |
| #define FLASH_FLAG_PGSERR FLASH_SR_PGSERR /*!< FLASH Programming sequence error flag */ |
| #define FLASH_FLAG_MISERR FLASH_SR_MISERR /*!< FLASH Fast programming data miss error flag */ |
| #define FLASH_FLAG_FASTERR FLASH_SR_FASTERR /*!< FLASH Fast programming error flag */ |
| #define FLASH_FLAG_OPTNV FLASH_SR_OPTNV /*!< FLASH User Option OPTVAL indication */ |
| #define FLASH_FLAG_RDERR FLASH_SR_RDERR /*!< FLASH PCROP read error flag */ |
| #define FLASH_FLAG_OPTVERR FLASH_SR_OPTVERR /*!< FLASH Option validity error flag */ |
| #define FLASH_FLAG_BSY FLASH_SR_BSY /*!< FLASH Busy flag */ |
| #define FLASH_FLAG_CFGBSY FLASH_SR_CFGBSY /*!< FLASH Programming/erase configuration busy */ |
| #define FLASH_FLAG_PESD FLASH_SR_PESD /*!< FLASH Programming/erase operation suspended */ |
| #define FLASH_FLAG_ECCC FLASH_ECCR_ECCC /*!< FLASH ECC correction */ |
| #define FLASH_FLAG_ECCD FLASH_ECCR_ECCD /*!< FLASH ECC detection */ |
| |
| #define FLASH_FLAG_SR_ERRORS (FLASH_FLAG_OPERR | FLASH_FLAG_PROGERR | FLASH_FLAG_WRPERR | \ |
| FLASH_FLAG_PGAERR | FLASH_FLAG_SIZERR | FLASH_FLAG_PGSERR | \ |
| FLASH_FLAG_MISERR | FLASH_FLAG_FASTERR | FLASH_FLAG_RDERR | \ |
| FLASH_FLAG_OPTVERR) /*!< All SR error flags */ |
| |
| #define FLASH_FLAG_ECCR_ERRORS (FLASH_FLAG_ECCC | FLASH_FLAG_ECCD) |
| |
| #define FLASH_FLAG_ALL_ERRORS (FLASH_FLAG_SR_ERRORS | FLASH_FLAG_ECCR_ERRORS) |
| |
| /** @defgroup FLASH_INTERRUPT_DEFINITION FLASH Interrupts Definition |
| * @brief FLASH Interrupt definition |
| * @{ |
| */ |
| #define FLASH_IT_EOP FLASH_CR_EOPIE /*!< End of FLASH Operation Interrupt source */ |
| #define FLASH_IT_OPERR FLASH_CR_ERRIE /*!< Error Interrupt source */ |
| #define FLASH_IT_RDERR FLASH_CR_RDERRIE /*!< PCROP Read Error Interrupt source */ |
| #define FLASH_IT_ECCC (FLASH_ECCR_ECCCIE >> FLASH_ECCR_ECCCIE_Pos) /*!< ECC Correction Interrupt source */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup FLASH_ERROR FLASH Error |
| * @{ |
| */ |
| #define HAL_FLASH_ERROR_NONE 0x00000000U |
| #define HAL_FLASH_ERROR_OP FLASH_FLAG_OPERR |
| #define HAL_FLASH_ERROR_PROG FLASH_FLAG_PROGERR |
| #define HAL_FLASH_ERROR_WRP FLASH_FLAG_WRPERR |
| #define HAL_FLASH_ERROR_PGA FLASH_FLAG_PGAERR |
| #define HAL_FLASH_ERROR_SIZ FLASH_FLAG_SIZERR |
| #define HAL_FLASH_ERROR_PGS FLASH_FLAG_PGSERR |
| #define HAL_FLASH_ERROR_MIS FLASH_FLAG_MISERR |
| #define HAL_FLASH_ERROR_FAST FLASH_FLAG_FASTERR |
| #define HAL_FLASH_ERROR_RD FLASH_FLAG_RDERR |
| #define HAL_FLASH_ERROR_OPTV FLASH_FLAG_OPTVERR |
| /** |
| * @} |
| */ |
| |
| /** @defgroup FLASH_TYPE_ERASE FLASH Erase Type |
| * @{ |
| */ |
| #define FLASH_TYPEERASE_PAGES FLASH_CR_PER /*!< Pages erase only*/ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup FLASH_TYPE_PROGRAM FLASH Program Type |
| * @{ |
| */ |
| #define FLASH_TYPEPROGRAM_DOUBLEWORD FLASH_CR_PG /*!< Program a double-word (64-bit) at a specified address.*/ |
| #define FLASH_TYPEPROGRAM_FAST FLASH_CR_FSTPG /*!< Fast program a 64 row double-word (64-bit) at a specified address. |
| And another 64 row double-word (64-bit) will be programmed */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup FLASH_OB_TYPE FLASH Option Bytes Type |
| * @{ |
| */ |
| #define OPTIONBYTE_WRP 0x00000001U /*!< WRP option byte configuration */ |
| #define OPTIONBYTE_RDP 0x00000002U /*!< RDP option byte configuration */ |
| #define OPTIONBYTE_USER 0x00000004U /*!< User option byte configuration */ |
| #define OPTIONBYTE_PCROP 0x00000008U /*!< PCROP option byte configuration */ |
| #define OPTIONBYTE_IPCC_BUF_ADDR 0x00000010U /*!< IPCC mailbox buffer address configuration */ |
| #define OPTIONBYTE_C2_BOOT_VECT 0x00000100U /*!< CPU2 Secure Boot reset vector */ |
| #define OPTIONBYTE_SECURE_MODE 0x00000200U /*!< Secure mode on activated or not */ |
| #define OPTIONBYTE_ALL (OPTIONBYTE_WRP | OPTIONBYTE_RDP | OPTIONBYTE_USER | \ |
| OPTIONBYTE_PCROP | OPTIONBYTE_IPCC_BUF_ADDR | OPTIONBYTE_C2_BOOT_VECT | \ |
| OPTIONBYTE_SECURE_MODE) /*!< All option byte configuration */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup FLASH_OB_WRP_AREA FLASH WRP Area |
| * @{ |
| */ |
| #define OB_WRPAREA_BANK1_AREAA 0x00000000U /*!< Flash Area A */ |
| #define OB_WRPAREA_BANK1_AREAB 0x00000001U /*!< Flash Area B */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup FLASH_OB_READ_PROTECTION FLASH Option Bytes Read Protection |
| * @{ |
| */ |
| #define OB_RDP_LEVEL_0 0x000000AAU |
| #define OB_RDP_LEVEL_1 0x000000BBU |
| #define OB_RDP_LEVEL_2 0x000000CCU /*!< Warning: When enabling read protection level 2 |
| it's no more possible to go back to level 1 or 0 */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup FLASH_OB_USER_TYPE FLASH Option Bytes User Type |
| * @{ |
| */ |
| #define OB_USER_BOR_LEV FLASH_OPTR_BOR_LEV /*!< BOR reset Level */ |
| #define OB_USER_nRST_STOP FLASH_OPTR_nRST_STOP /*!< Reset generated when entering the stop mode */ |
| #define OB_USER_nRST_STDBY FLASH_OPTR_nRST_STDBY /*!< Reset generated when entering the standby mode */ |
| #define OB_USER_nRST_SHDW FLASH_OPTR_nRST_SHDW /*!< Reset generated when entering the shutdown mode */ |
| #define OB_USER_IWDG_SW FLASH_OPTR_IWDG_SW /*!< Independent watchdog selection */ |
| #define OB_USER_IWDG_STOP FLASH_OPTR_IWDG_STOP /*!< Independent watchdog counter freeze in stop mode */ |
| #define OB_USER_IWDG_STDBY FLASH_OPTR_IWDG_STDBY /*!< Independent watchdog counter freeze in standby mode */ |
| #define OB_USER_WWDG_SW FLASH_OPTR_WWDG_SW /*!< Window watchdog selection */ |
| #define OB_USER_nBOOT1 FLASH_OPTR_nBOOT1 /*!< Boot configuration */ |
| #define OB_USER_SRAM2PE FLASH_OPTR_SRAM2PE /*!< SRAM2 parity check enable */ |
| #define OB_USER_SRAM2RST FLASH_OPTR_SRAM2RST /*!< SRAM2 erase when system reset */ |
| #define OB_USER_nSWBOOT0 FLASH_OPTR_nSWBOOT0 /*!< Software BOOT0 */ |
| #define OB_USER_nBOOT0 FLASH_OPTR_nBOOT0 /*!< nBOOT0 option bit */ |
| #define OB_USER_AGC_TRIM FLASH_OPTR_AGC_TRIM /*!< Automatic Gain Control Trimming */ |
| #define OB_USER_ALL (OB_USER_BOR_LEV | OB_USER_nRST_STOP | OB_USER_nRST_STDBY | \ |
| OB_USER_nRST_SHDW | OB_USER_IWDG_SW | OB_USER_IWDG_STOP | \ |
| OB_USER_IWDG_STDBY | OB_USER_WWDG_SW | OB_USER_nBOOT1 | \ |
| OB_USER_SRAM2PE | OB_USER_SRAM2RST | OB_USER_nSWBOOT0 | \ |
| OB_USER_nBOOT0 | OB_USER_AGC_TRIM) /*!< all option bits */ |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup FLASH_OB_USER_AGC_TRIM FLASH Option Bytes Automatic Gain Control Trimming |
| * @{ |
| */ |
| #define OB_AGC_TRIM_0 0x00000000U /*!< Automatic Gain Control Trimming Value 0 */ |
| #define OB_AGC_TRIM_1 FLASH_OPTR_AGC_TRIM_0 /*!< Automatic Gain Control Trimming Value 1 */ |
| #define OB_AGC_TRIM_2 FLASH_OPTR_AGC_TRIM_1 /*!< Automatic Gain Control Trimming Value 2 */ |
| #define OB_AGC_TRIM_3 (FLASH_OPTR_AGC_TRIM_1 | FLASH_OPTR_AGC_TRIM_0) /*!< Automatic Gain Control Trimming Value 3 */ |
| #define OB_AGC_TRIM_4 FLASH_OPTR_AGC_TRIM_2 /*!< Automatic Gain Control Trimming Value 4 */ |
| #define OB_AGC_TRIM_5 (FLASH_OPTR_AGC_TRIM_2 | FLASH_OPTR_AGC_TRIM_0) /*!< Automatic Gain Control Trimming Value 5 */ |
| #define OB_AGC_TRIM_6 (FLASH_OPTR_AGC_TRIM_2 | FLASH_OPTR_AGC_TRIM_1) /*!< Automatic Gain Control Trimming Value 6 */ |
| #define OB_AGC_TRIM_7 (FLASH_OPTR_AGC_TRIM_2 | FLASH_OPTR_AGC_TRIM_1 | FLASH_OPTR_AGC_TRIM_0) /*!< Automatic Gain Control Trimming Value 7 */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup FLASH_OB_USER_BOR_LEVEL FLASH Option Bytes User BOR Level |
| * @{ |
| */ |
| #define OB_BOR_LEVEL_0 0x00000000U /*!< Reset level threshold is around 1.7V */ |
| #define OB_BOR_LEVEL_1 FLASH_OPTR_BOR_LEV_0 /*!< Reset level threshold is around 2.0V */ |
| #define OB_BOR_LEVEL_2 FLASH_OPTR_BOR_LEV_1 /*!< Reset level threshold is around 2.2V */ |
| #define OB_BOR_LEVEL_3 (FLASH_OPTR_BOR_LEV_0 | FLASH_OPTR_BOR_LEV_1) /*!< Reset level threshold is around 2.5V */ |
| #define OB_BOR_LEVEL_4 FLASH_OPTR_BOR_LEV_2 /*!< Reset level threshold is around 2.8V */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup FLASH_OB_USER_nRST_STOP FLASH Option Bytes User Reset On Stop |
| * @{ |
| */ |
| #define OB_STOP_RST 0x00000000U /*!< Reset generated when entering the stop mode */ |
| #define OB_STOP_NORST FLASH_OPTR_nRST_STOP /*!< No reset generated when entering the stop mode */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup FLASH_OB_USER_nRST_STANDBY FLASH Option Bytes User Reset On Standby |
| * @{ |
| */ |
| #define OB_STANDBY_RST 0x00000000U /*!< Reset generated when entering the standby mode */ |
| #define OB_STANDBY_NORST FLASH_OPTR_nRST_STDBY /*!< No reset generated when entering the standby mode */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup FLASH_OB_USER_nRST_SHUTDOWN FLASH Option Bytes User Reset On Shutdown |
| * @{ |
| */ |
| #define OB_SHUTDOWN_RST 0x00000000U /*!< Reset generated when entering the shutdown mode */ |
| #define OB_SHUTDOWN_NORST FLASH_OPTR_nRST_SHDW /*!< No reset generated when entering the shutdown mode */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup FLASH_OB_USER_IWDG_SW FLASH Option Bytes User IWDG Type |
| * @{ |
| */ |
| #define OB_IWDG_HW 0x00000000U /*!< Hardware independent watchdog */ |
| #define OB_IWDG_SW FLASH_OPTR_IWDG_SW /*!< Software independent watchdog */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup FLASH_OB_USER_IWDG_STOP FLASH Option Bytes User IWDG Mode On Stop |
| * @{ |
| */ |
| #define OB_IWDG_STOP_FREEZE 0x00000000U /*!< Independent watchdog counter is frozen in Stop mode */ |
| #define OB_IWDG_STOP_RUN FLASH_OPTR_IWDG_STOP /*!< Independent watchdog counter is running in Stop mode */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup FLASH_OB_USER_IWDG_STANDBY FLASH Option Bytes User IWDG Mode On Standby |
| * @{ |
| */ |
| #define OB_IWDG_STDBY_FREEZE 0x00000000U /*!< Independent watchdog counter is frozen in Standby mode */ |
| #define OB_IWDG_STDBY_RUN FLASH_OPTR_IWDG_STDBY /*!< Independent watchdog counter is running in Standby mode */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup FLASH_OB_USER_WWDG_SW FLASH Option Bytes User WWDG Type |
| * @{ |
| */ |
| #define OB_WWDG_HW 0x00000000U /*!< Hardware window watchdog */ |
| #define OB_WWDG_SW FLASH_OPTR_WWDG_SW /*!< Software window watchdog */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup FLASH_OB_USER_SRAM2PE FLASH Option Bytes SRAM2 parity check |
| * @{ |
| */ |
| #define OB_SRAM2_PARITY_ENABLE 0x00000000U /*!< SRAM2 parity check enable */ |
| #define OB_SRAM2_PARITY_DISABLE FLASH_OPTR_SRAM2PE /*!< SRAM2 parity check disable */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup FLASH_OB_USER_SRAM2RST FLASH Option Bytes SRAM2 erase when system reset |
| * @{ |
| */ |
| #define OB_SRAM2_RST_ERASE 0x00000000U /*!< SRAM2 erased when a system reset */ |
| #define OB_SRAM2_RST_NOT_ERASE FLASH_OPTR_SRAM2RST /*!< SRAM2 is not erased when a system reset */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup FLASH_OB_USER_nBOOT1 FLASH Option Bytes User BOOT1 Type |
| * @{ |
| */ |
| #define OB_BOOT1_SRAM 0x00000000U /*!< Embedded SRAM is selected as boot space (if BOOT0=1) */ |
| #define OB_BOOT1_SYSTEM FLASH_OPTR_nBOOT1 /*!< System memory is selected as boot space (if BOOT0=1) */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup FLASH_OB_USER_nSWBOOT0 FLASH Option Bytes User Software BOOT0 |
| * @{ |
| */ |
| #define OB_BOOT0_FROM_OB 0x00000000U /*!< BOOT0 taken from the option bit nBOOT0 */ |
| #define OB_BOOT0_FROM_PIN FLASH_OPTR_nSWBOOT0 /*!< BOOT0 taken from PH3/BOOT0 pin */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup FLASH_OB_USER_nBOOT0 FLASH Option Bytes User nBOOT0 option bit |
| * @{ |
| */ |
| #define OB_BOOT0_RESET 0x00000000U /*!< nBOOT0 = 0 */ |
| #define OB_BOOT0_SET FLASH_OPTR_nBOOT0 /*!< nBOOT0 = 1 */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup FLASH_OB_PCROP_ZONE FLASH PCROP ZONE |
| * @{ |
| */ |
| #define OB_PCROP_ZONE_A 0x00000001U /*!< PCROP Zone A */ |
| #define OB_PCROP_ZONE_B 0x00000002U /*!< PCROP Zone B */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup FLASH_OB_PCROP_RDP FLASH Option Bytes PCROP On RDP Level Type |
| * @{ |
| */ |
| #define OB_PCROP_RDP_NOT_ERASE 0x00000000U /*!< PCROP area is not erased when the RDP level |
| is decreased from Level 1 to Level 0 */ |
| #define OB_PCROP_RDP_ERASE FLASH_PCROP1AER_PCROP_RDP /*!< PCROP area is erased when the RDP level is |
| decreased from Level 1 to Level 0 (full mass erase) */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup FLASH_OB_SECURITY_MODE Option Bytes FLASH Secure mode |
| * @{ |
| */ |
| #define SYSTEM_NOT_IN_SECURE_MODE 0x00000000U /*!< Unsecure mode: Security disabled */ |
| #define SYSTEM_IN_SECURE_MODE FLASH_OPTR_ESE /*!< Secure mode : Security enabled */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup C2_FLASH_OB_BOOT_REGION CPU2 Option Bytes Reset Boot Vector |
| * @{ |
| */ |
| #define OB_C2_BOOT_FROM_SRAM 0x00000000U /*!< CPU2 boot from Sram */ |
| #define OB_C2_BOOT_FROM_FLASH FLASH_SRRVR_C2OPT /*!< CPU2 boot from Flash */ |
| /** |
| * @} |
| */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup FLASH_SRAM2A_ADDRESS_RANGE RAM2A address range in secure mode |
| * @{ |
| */ |
| |
| #define SRAM2A_START_SECURE_ADDR_0 (SRAM2A_BASE + 0x0000U) /* When in secure mode (SRAM2A_BASE + 0x0000) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_1 (SRAM2A_BASE + 0x0400U) /* When in secure mode (SRAM2A_BASE + 0x0400) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_2 (SRAM2A_BASE + 0x0800U) /* When in secure mode (SRAM2A_BASE + 0x0800) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_3 (SRAM2A_BASE + 0x0C00U) /* When in secure mode (SRAM2A_BASE + 0x0C00) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_4 (SRAM2A_BASE + 0x1000U) /* When in secure mode (SRAM2A_BASE + 0x1000) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_5 (SRAM2A_BASE + 0x1400U) /* When in secure mode (SRAM2A_BASE + 0x1400) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_6 (SRAM2A_BASE + 0x1800U) /* When in secure mode (SRAM2A_BASE + 0x1800) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_7 (SRAM2A_BASE + 0x1C00U) /* When in secure mode (SRAM2A_BASE + 0x1C00) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_8 (SRAM2A_BASE + 0x2000U) /* When in secure mode (SRAM2A_BASE + 0x2000) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_9 (SRAM2A_BASE + 0x2400U) /* When in secure mode (SRAM2A_BASE + 0x2400) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_10 (SRAM2A_BASE + 0x2800U) /* When in secure mode (SRAM2A_BASE + 0x2800) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_11 (SRAM2A_BASE + 0x2C00U) /* When in secure mode (SRAM2A_BASE + 0x2C00) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_12 (SRAM2A_BASE + 0x3000U) /* When in secure mode (SRAM2A_BASE + 0x3000) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_13 (SRAM2A_BASE + 0x3400U) /* When in secure mode (SRAM2A_BASE + 0x3400) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_14 (SRAM2A_BASE + 0x3800U) /* When in secure mode (SRAM2A_BASE + 0x3800) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_15 (SRAM2A_BASE + 0x3C00U) /* When in secure mode (SRAM2A_BASE + 0x3C00) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_16 (SRAM2A_BASE + 0x4000U) /* When in secure mode (SRAM2A_BASE + 0x4000) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_17 (SRAM2A_BASE + 0x4400U) /* When in secure mode (SRAM2A_BASE + 0x4400) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_18 (SRAM2A_BASE + 0x4800U) /* When in secure mode (SRAM2A_BASE + 0x4800) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_19 (SRAM2A_BASE + 0x4C00U) /* When in secure mode (SRAM2A_BASE + 0x4C00) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_20 (SRAM2A_BASE + 0x5000U) /* When in secure mode (SRAM2A_BASE + 0x5000) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_21 (SRAM2A_BASE + 0x5400U) /* When in secure mode (SRAM2A_BASE + 0x5400) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_22 (SRAM2A_BASE + 0x5800U) /* When in secure mode (SRAM2A_BASE + 0x5800) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_23 (SRAM2A_BASE + 0x5C00U) /* When in secure mode (SRAM2A_BASE + 0x5C00) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_24 (SRAM2A_BASE + 0x6000U) /* When in secure mode (SRAM2A_BASE + 0x6000) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_25 (SRAM2A_BASE + 0x6400U) /* When in secure mode (SRAM2A_BASE + 0x6400) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_26 (SRAM2A_BASE + 0x6800U) /* When in secure mode (SRAM2A_BASE + 0x6800) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_27 (SRAM2A_BASE + 0x6C00U) /* When in secure mode (SRAM2A_BASE + 0x6C00) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_28 (SRAM2A_BASE + 0x7000U) /* When in secure mode (SRAM2A_BASE + 0x7000) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_29 (SRAM2A_BASE + 0x7400U) /* When in secure mode (SRAM2A_BASE + 0x7400) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_30 (SRAM2A_BASE + 0x7800U) /* When in secure mode (SRAM2A_BASE + 0x7800) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_START_SECURE_ADDR_31 (SRAM2A_BASE + 0x7C00U) /* When in secure mode (SRAM2A_BASE + 0x7C00) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2A_FULL_UNSECURE (SRAM2A_BASE + 0x8000U) /* The RAM2A is accessible to M0 Plus and M4 */ |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup FLASH_SRAM2B_ADDRESS_RANGE RAM2B address range in secure mode |
| * @{ |
| */ |
| |
| #define SRAM2B_START_SECURE_ADDR_0 (SRAM2B_BASE + 0x0000U) /* When in secure mode (SRAM2B_BASE + 0x0000) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_1 (SRAM2B_BASE + 0x0400U) /* When in secure mode (SRAM2B_BASE + 0x0400) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_2 (SRAM2B_BASE + 0x0800U) /* When in secure mode (SRAM2B_BASE + 0x0800) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_3 (SRAM2B_BASE + 0x0C00U) /* When in secure mode (SRAM2B_BASE + 0x0C00) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_4 (SRAM2B_BASE + 0x1000U) /* When in secure mode (SRAM2B_BASE + 0x1000) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_5 (SRAM2B_BASE + 0x1400U) /* When in secure mode (SRAM2B_BASE + 0x1400) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_6 (SRAM2B_BASE + 0x1800U) /* When in secure mode (SRAM2B_BASE + 0x1800) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_7 (SRAM2B_BASE + 0x1C00U) /* When in secure mode (SRAM2B_BASE + 0x1C00) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_8 (SRAM2B_BASE + 0x2000U) /* When in secure mode (SRAM2B_BASE + 0x2000) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_9 (SRAM2B_BASE + 0x2400U) /* When in secure mode (SRAM2B_BASE + 0x2400) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_10 (SRAM2B_BASE + 0x2800U) /* When in secure mode (SRAM2B_BASE + 0x2800) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_11 (SRAM2B_BASE + 0x2C00U) /* When in secure mode (SRAM2B_BASE + 0x2C00) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_12 (SRAM2B_BASE + 0x3000U) /* When in secure mode (SRAM2B_BASE + 0x3000) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_13 (SRAM2B_BASE + 0x3400U) /* When in secure mode (SRAM2B_BASE + 0x3400) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_14 (SRAM2B_BASE + 0x3800U) /* When in secure mode (SRAM2B_BASE + 0x3800) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_15 (SRAM2B_BASE + 0x3C00U) /* When in secure mode (SRAM2B_BASE + 0x3C00) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_16 (SRAM2B_BASE + 0x4000U) /* When in secure mode (SRAM2B_BASE + 0x4000) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_17 (SRAM2B_BASE + 0x4400U) /* When in secure mode (SRAM2B_BASE + 0x4400) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_18 (SRAM2B_BASE + 0x4800U) /* When in secure mode (SRAM2B_BASE + 0x4800) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_19 (SRAM2B_BASE + 0x4C00U) /* When in secure mode (SRAM2B_BASE + 0x4C00) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_20 (SRAM2B_BASE + 0x5000U) /* When in secure mode (SRAM2B_BASE + 0x5000) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_21 (SRAM2B_BASE + 0x5400U) /* When in secure mode (SRAM2B_BASE + 0x5400) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_22 (SRAM2B_BASE + 0x5800U) /* When in secure mode (SRAM2B_BASE + 0x5800) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_23 (SRAM2B_BASE + 0x5C00U) /* When in secure mode (SRAM2B_BASE + 0x5C00) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_24 (SRAM2B_BASE + 0x6000U) /* When in secure mode (SRAM2B_BASE + 0x6000) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_25 (SRAM2B_BASE + 0x6400U) /* When in secure mode (SRAM2B_BASE + 0x6400) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_26 (SRAM2B_BASE + 0x6800U) /* When in secure mode (SRAM2B_BASE + 0x6800) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_27 (SRAM2B_BASE + 0x6C00U) /* When in secure mode (SRAM2B_BASE + 0x6C00) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_28 (SRAM2B_BASE + 0x7000U) /* When in secure mode (SRAM2B_BASE + 0x7000) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_29 (SRAM2B_BASE + 0x7400U) /* When in secure mode (SRAM2B_BASE + 0x7400) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_30 (SRAM2B_BASE + 0x7800U) /* When in secure mode (SRAM2B_BASE + 0x7800) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_START_SECURE_ADDR_31 (SRAM2B_BASE + 0x7C00U) /* When in secure mode (SRAM2B_BASE + 0x7C00) -> SRAM2B_END_ADDR is accessible only by M0 Plus */ |
| #define SRAM2B_FULL_UNSECURE (SRAM2B_BASE + 0x8000U) /* The RAM2B is accessible to M0 Plus and M4 */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Exported macros -----------------------------------------------------------*/ |
| /** @defgroup FLASH_Exported_Macros FLASH Exported Macros |
| * @brief macros to control FLASH features |
| * @{ |
| */ |
| |
| /** |
| * @brief Set the FLASH Latency. |
| * @param __LATENCY__ FLASH Latency |
| * This parameter can be one of the following values : |
| * @arg @ref FLASH_LATENCY_0 FLASH Zero wait state |
| * @arg @ref FLASH_LATENCY_1 FLASH One wait state |
| * @arg @ref FLASH_LATENCY_2 FLASH Two wait states |
| * @arg @ref FLASH_LATENCY_3 FLASH Three wait states |
| * @retval None |
| */ |
| #define __HAL_FLASH_SET_LATENCY(__LATENCY__) MODIFY_REG(FLASH->ACR, FLASH_ACR_LATENCY, (__LATENCY__)) |
| |
| /** |
| * @brief Get the FLASH Latency. |
| * @retval FLASH Latency |
| * Returned value can be one of the following values : |
| * @arg @ref FLASH_LATENCY_0 FLASH Zero wait state |
| * @arg @ref FLASH_LATENCY_1 FLASH One wait state |
| * @arg @ref FLASH_LATENCY_2 FLASH Two wait states |
| * @arg @ref FLASH_LATENCY_3 FLASH Three wait states |
| */ |
| #define __HAL_FLASH_GET_LATENCY() READ_BIT(FLASH->ACR, FLASH_ACR_LATENCY) |
| |
| /** |
| * @brief Enable the FLASH prefetch buffer. |
| * @retval None |
| */ |
| #define __HAL_FLASH_PREFETCH_BUFFER_ENABLE() SET_BIT(FLASH->ACR, FLASH_ACR_PRFTEN) |
| |
| /** |
| * @brief Disable the FLASH prefetch buffer. |
| * @retval None |
| */ |
| #define __HAL_FLASH_PREFETCH_BUFFER_DISABLE() CLEAR_BIT(FLASH->ACR, FLASH_ACR_PRFTEN) |
| |
| /** |
| * @brief Enable the FLASH instruction cache. |
| * @retval none |
| */ |
| #define __HAL_FLASH_INSTRUCTION_CACHE_ENABLE() SET_BIT(FLASH->ACR, FLASH_ACR_ICEN) |
| |
| /** |
| * @brief Disable the FLASH instruction cache. |
| * @retval none |
| */ |
| #define __HAL_FLASH_INSTRUCTION_CACHE_DISABLE() CLEAR_BIT(FLASH->ACR, FLASH_ACR_ICEN) |
| |
| /** |
| * @brief Enable the FLASH data cache. |
| * @retval none |
| */ |
| #define __HAL_FLASH_DATA_CACHE_ENABLE() SET_BIT(FLASH->ACR, FLASH_ACR_DCEN) |
| |
| /** |
| * @brief Disable the FLASH data cache. |
| * @retval none |
| */ |
| #define __HAL_FLASH_DATA_CACHE_DISABLE() CLEAR_BIT(FLASH->ACR, FLASH_ACR_DCEN) |
| |
| /** |
| * @brief Reset the FLASH instruction Cache. |
| * @note This function must be used only when the Instruction Cache is disabled. |
| * @retval None |
| */ |
| #define __HAL_FLASH_INSTRUCTION_CACHE_RESET() do { SET_BIT(FLASH->ACR, FLASH_ACR_ICRST); \ |
| CLEAR_BIT(FLASH->ACR, FLASH_ACR_ICRST); \ |
| } while (0) |
| |
| /** |
| * @brief Reset the FLASH data Cache. |
| * @note This function must be used only when the data Cache is disabled. |
| * @retval None |
| */ |
| #define __HAL_FLASH_DATA_CACHE_RESET() do { SET_BIT(FLASH->ACR, FLASH_ACR_DCRST); \ |
| CLEAR_BIT(FLASH->ACR, FLASH_ACR_DCRST); \ |
| } while (0) |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup FLASH_Interrupt FLASH Interrupts Macros |
| * @brief macros to handle FLASH interrupts |
| * @{ |
| */ |
| |
| /** |
| * @brief Enable the specified FLASH interrupt. |
| * @param __INTERRUPT__ FLASH interrupt |
| * This parameter can be any combination of the following values: |
| * @arg @ref FLASH_IT_EOP End of FLASH Operation Interrupt |
| * @arg @ref FLASH_IT_OPERR Error Interrupt |
| * @arg @ref FLASH_IT_RDERR PCROP Read Error Interrupt |
| * @arg @ref FLASH_IT_ECCC ECC Correction Interrupt |
| * @retval none |
| */ |
| #define __HAL_FLASH_ENABLE_IT(__INTERRUPT__) do { if(((__INTERRUPT__) & FLASH_IT_ECCC) != 0U) { SET_BIT(FLASH->ECCR, FLASH_ECCR_ECCCIE); }\ |
| if(((__INTERRUPT__) & (~FLASH_IT_ECCC)) != 0U) { SET_BIT(FLASH->CR, ((__INTERRUPT__) & (~FLASH_IT_ECCC))); }\ |
| } while(0) |
| |
| /** |
| * @brief Disable the specified FLASH interrupt. |
| * @param __INTERRUPT__ FLASH interrupt |
| * This parameter can be any combination of the following values: |
| * @arg @ref FLASH_IT_EOP End of FLASH Operation Interrupt |
| * @arg @ref FLASH_IT_OPERR Error Interrupt |
| * @arg @ref FLASH_IT_RDERR PCROP Read Error Interrupt |
| * @arg @ref FLASH_IT_ECCC ECC Correction Interrupt |
| * @retval none |
| */ |
| #define __HAL_FLASH_DISABLE_IT(__INTERRUPT__) do { if(((__INTERRUPT__) & FLASH_IT_ECCC) != 0U) { CLEAR_BIT(FLASH->ECCR, FLASH_ECCR_ECCCIE); }\ |
| if(((__INTERRUPT__) & (~FLASH_IT_ECCC)) != 0U) { CLEAR_BIT(FLASH->CR, ((__INTERRUPT__) & (~FLASH_IT_ECCC))); }\ |
| } while(0) |
| |
| /** |
| * @brief Check whether the specified FLASH flag is set or not. |
| * @param __FLAG__ specifies the FLASH flag to check. |
| * This parameter can be one of the following values: |
| * @arg @ref FLASH_FLAG_EOP FLASH End of Operation flag |
| * @arg @ref FLASH_FLAG_OPERR FLASH Operation error flag |
| * @arg @ref FLASH_FLAG_PROGERR FLASH Programming error flag |
| * @arg @ref FLASH_FLAG_WRPERR FLASH Write protection error flag |
| * @arg @ref FLASH_FLAG_PGAERR FLASH Programming alignment error flag |
| * @arg @ref FLASH_FLAG_SIZERR FLASH Size error flag |
| * @arg @ref FLASH_FLAG_PGSERR FLASH Programming sequence error flag |
| * @arg @ref FLASH_FLAG_MISERR FLASH Fast programming data miss error flag |
| * @arg @ref FLASH_FLAG_FASTERR FLASH Fast programming error flag |
| * @arg @ref FLASH_FLAG_OPTNV FLASH User Option OPTVAL indication |
| * @arg @ref FLASH_FLAG_RDERR FLASH PCROP read error flag |
| * @arg @ref FLASH_FLAG_OPTVERR FLASH Option validity error flag |
| * @arg @ref FLASH_FLAG_BSY FLASH write/erase operations in progress flag |
| * @arg @ref FLASH_FLAG_CFGBSY Programming/erase configuration busy |
| * @arg @ref FLASH_FLAG_PESD FLASH Programming/erase operation suspended |
| * @arg @ref FLASH_FLAG_ECCC FLASH one ECC error has been detected and corrected |
| * @arg @ref FLASH_FLAG_ECCD FLASH two ECC errors have been detected |
| * @retval The new state of FLASH_FLAG (SET or RESET). |
| */ |
| #define __HAL_FLASH_GET_FLAG(__FLAG__) ((((__FLAG__) & (FLASH_FLAG_ECCR_ERRORS)) != 0U) ? \ |
| (READ_BIT(FLASH->ECCR, (__FLAG__)) == (__FLAG__)) : \ |
| (READ_BIT(FLASH->SR, (__FLAG__)) == (__FLAG__))) |
| /** |
| * @brief Clear the FLASH's pending flags. |
| * @param __FLAG__ specifies the FLASH flags to clear. |
| * This parameter can be any combination of the following values: |
| * @arg @ref FLASH_FLAG_EOP FLASH End of Operation flag |
| * @arg @ref FLASH_FLAG_OPERR FLASH Operation error flag |
| * @arg @ref FLASH_FLAG_PROGERR FLASH Programming error flag |
| * @arg @ref FLASH_FLAG_WRPERR FLASH Write protection error flag |
| * @arg @ref FLASH_FLAG_PGAERR FLASH Programming alignment error flag |
| * @arg @ref FLASH_FLAG_SIZERR FLASH Size error flag |
| * @arg @ref FLASH_FLAG_PGSERR FLASH Programming sequence error flag |
| * @arg @ref FLASH_FLAG_MISERR FLASH Fast programming data miss error flag |
| * @arg @ref FLASH_FLAG_FASTERR FLASH Fast programming error flag |
| * @arg @ref FLASH_FLAG_RDERR FLASH PCROP read error flag |
| * @arg @ref FLASH_FLAG_OPTVERR FLASH Option validity error flag |
| * @arg @ref FLASH_FLAG_ECCC FLASH one ECC error has been detected and corrected |
| * @arg @ref FLASH_FLAG_ECCD FLASH two ECC errors have been detected |
| * @arg @ref FLASH_FLAG_SR_ERRORS FLASH All SR errors flags |
| * @arg @ref FLASH_FLAG_ECCR_ERRORS FLASH All ECCR errors flags |
| * @arg @ref FLASH_FLAG_ALL_ERRORS FLASH All errors flags |
| * @retval None |
| */ |
| #define __HAL_FLASH_CLEAR_FLAG(__FLAG__) do { if(((__FLAG__) & (FLASH_FLAG_ECCR_ERRORS)) != 0U) { SET_BIT(FLASH->ECCR, ((__FLAG__) & (FLASH_FLAG_ECCR_ERRORS))); }\ |
| if(((__FLAG__) & ~(FLASH_FLAG_ECCR_ERRORS)) != 0U) { WRITE_REG(FLASH->SR, ((__FLAG__) & ~(FLASH_FLAG_ECCR_ERRORS))); }\ |
| } while(0) |
| /** |
| * @} |
| */ |
| |
| /* Include FLASH HAL Extended module */ |
| #include "stm32wbxx_hal_flash_ex.h" |
| /* Exported variables --------------------------------------------------------*/ |
| /** @defgroup FLASH_Exported_Variables FLASH Exported Variables |
| * @{ |
| */ |
| extern FLASH_ProcessTypeDef pFlash; |
| /** |
| * @} |
| */ |
| |
| /* Exported functions --------------------------------------------------------*/ |
| /** @addtogroup FLASH_Exported_Functions |
| * @{ |
| */ |
| |
| /* Program operation functions ***********************************************/ |
| /** @addtogroup FLASH_Exported_Functions_Group1 |
| * @{ |
| */ |
| HAL_StatusTypeDef HAL_FLASH_Program(uint32_t TypeProgram, uint32_t Address, uint64_t Data); |
| HAL_StatusTypeDef HAL_FLASH_Program_IT(uint32_t TypeProgram, uint32_t Address, uint64_t Data); |
| /* FLASH IRQ handler method */ |
| void HAL_FLASH_IRQHandler(void); |
| /* Callbacks in non blocking modes */ |
| void HAL_FLASH_EndOfOperationCallback(uint32_t ReturnValue); |
| void HAL_FLASH_OperationErrorCallback(uint32_t ReturnValue); |
| /** |
| * @} |
| */ |
| |
| /* Peripheral Control functions **********************************************/ |
| /** @addtogroup FLASH_Exported_Functions_Group2 |
| * @{ |
| */ |
| HAL_StatusTypeDef HAL_FLASH_Unlock(void); |
| HAL_StatusTypeDef HAL_FLASH_Lock(void); |
| /* Option bytes control */ |
| HAL_StatusTypeDef HAL_FLASH_OB_Unlock(void); |
| HAL_StatusTypeDef HAL_FLASH_OB_Lock(void); |
| HAL_StatusTypeDef HAL_FLASH_OB_Launch(void); |
| /** |
| * @} |
| */ |
| |
| /* Peripheral State functions ************************************************/ |
| /** @addtogroup FLASH_Exported_Functions_Group3 |
| * @{ |
| */ |
| uint32_t HAL_FLASH_GetError(void); |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Private types --------------------------------------------------------*/ |
| /** @defgroup FLASH_Private_types FLASH Private Types |
| * @{ |
| */ |
| HAL_StatusTypeDef FLASH_WaitForLastOperation(uint32_t Timeout); |
| /** |
| * @} |
| */ |
| |
| /* Private constants --------------------------------------------------------*/ |
| /** @defgroup FLASH_Private_Constants FLASH Private Constants |
| * @{ |
| */ |
| #define FLASH_END_ADDR (FLASH_BASE + FLASH_SIZE - 1U) |
| |
| #define FLASH_BANK_SIZE FLASH_SIZE /*!< FLASH Bank Size */ |
| #define FLASH_PAGE_SIZE 0x00001000U /*!< FLASH Page Size, 4 KBytes */ |
| #define FLASH_PAGE_NB (FLASH_SIZE / FLASH_PAGE_SIZE) |
| #define FLASH_TIMEOUT_VALUE 1000U /*!< FLASH Execution Timeout, 1 s */ |
| |
| #define FLASH_PCROP_GRANULARITY_OFFSET 11U /*!< FLASH Code Readout Protection granularity offset */ |
| #define FLASH_PCROP_GRANULARITY (1UL << FLASH_PCROP_GRANULARITY_OFFSET) /*!< FLASH Code Readout Protection granularity, 2 KBytes */ |
| |
| #define FLASH_TYPENONE 0x00000000U /*!< No Programmation Procedure On Going */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SRAM_MEMORY_SIZE SRAM memory size |
| * @{ |
| */ |
| #define SRAM_SECURE_PAGE_GRANULARITY_OFFSET 10U /*!< Secure SRAM2A and SRAM2B Protection granularity offset */ |
| #define SRAM_SECURE_PAGE_GRANULARITY (1UL << FLASH_PCROP_GRANULARITY_OFFSET) /*!< Secure SRAM2A and SRAM2B Protection granularity, 1KBytes */ |
| /** |
| * @} |
| */ |
| |
| /* Private macros ------------------------------------------------------------*/ |
| /** @defgroup FLASH_Private_Macros FLASH Private Macros |
| * @{ |
| */ |
| #define IS_FLASH_MAIN_MEM_ADDRESS(__VALUE__) (((__VALUE__) >= FLASH_BASE) && ((__VALUE__) <= (FLASH_BASE + FLASH_SIZE - 1UL))) |
| |
| #define IS_FLASH_FAST_PROGRAM_ADDRESS(__VALUE__) (((__VALUE__) >= FLASH_BASE) && ((__VALUE__) <= (FLASH_BASE + FLASH_SIZE - 256UL)) && (((__VALUE__) % 256UL) == 0UL)) |
| |
| #define IS_FLASH_PROGRAM_MAIN_MEM_ADDRESS(__VALUE__) (((__VALUE__) >= FLASH_BASE) && ((__VALUE__) <= (FLASH_BASE + FLASH_SIZE - 8UL)) && (((__VALUE__) % 8UL) == 0UL)) |
| |
| #define IS_FLASH_PROGRAM_OTP_ADDRESS(__VALUE__) (((__VALUE__) >= OTP_AREA_BASE) && ((__VALUE__) <= (OTP_AREA_END_ADDR + 1UL - 8UL)) && (((__VALUE__) % 8UL) == 0UL)) |
| |
| #define IS_FLASH_PROGRAM_ADDRESS(__VALUE__) (IS_FLASH_PROGRAM_MAIN_MEM_ADDRESS(__VALUE__) || IS_FLASH_PROGRAM_OTP_ADDRESS(__VALUE__)) |
| |
| #define IS_FLASH_PAGE(__VALUE__) ((__VALUE__) < FLASH_PAGE_NB) |
| |
| #define IS_ADDR_ALIGNED_64BITS(__VALUE__) (((__VALUE__) & 0x7U) == (0x00UL)) |
| |
| #define IS_FLASH_TYPEERASE(__VALUE__) ((__VALUE__) == FLASH_TYPEERASE_PAGES) |
| |
| #define IS_FLASH_TYPEPROGRAM(__VALUE__) (((__VALUE__) == FLASH_TYPEPROGRAM_DOUBLEWORD) || \ |
| ((__VALUE__) == FLASH_TYPEPROGRAM_FAST)) |
| |
| #define IS_OB_SFSA_START_ADDR(__VALUE__) (((__VALUE__) >= FLASH_BASE) && ((__VALUE__) <= FLASH_END_ADDR) && (((__VALUE__) & ~(uint32_t)0xFFFU) == (__VALUE__))) |
| #define IS_OB_SBRSA_START_ADDR(__VALUE__) (((__VALUE__) >= SRAM2A_BASE) && ((__VALUE__) <= (SRAM2A_BASE + SRAM2A_SIZE - 1U)) && (((__VALUE__) & ~0x3FFU) == (__VALUE__))) |
| #define IS_OB_SNBRSA_START_ADDR(__VALUE__) (((__VALUE__) >= SRAM2B_BASE) && ((__VALUE__) <= (SRAM2B_BASE + SRAM2B_SIZE - 1U)) && (((__VALUE__) & ~0x3FFU) == (__VALUE__))) |
| #define IS_OB_SECURE_MODE(__VALUE__) (((__VALUE__) == SYSTEM_IN_SECURE_MODE) || ((__VALUE__) == SYSTEM_NOT_IN_SECURE_MODE)) |
| |
| #define IS_OPTIONBYTE(__VALUE__) (((__VALUE__) <= (OPTIONBYTE_WRP | OPTIONBYTE_RDP | OPTIONBYTE_USER | OPTIONBYTE_PCROP | \ |
| OPTIONBYTE_IPCC_BUF_ADDR | OPTIONBYTE_C2_BOOT_VECT | OPTIONBYTE_SECURE_MODE))) |
| |
| #define IS_OB_WRPAREA(__VALUE__) (((__VALUE__) == OB_WRPAREA_BANK1_AREAA) || ((__VALUE__) == OB_WRPAREA_BANK1_AREAB)) |
| |
| #define IS_OB_RDP_LEVEL(__VALUE__) (((__VALUE__) == OB_RDP_LEVEL_0) ||\ |
| ((__VALUE__) == OB_RDP_LEVEL_1) ||\ |
| ((__VALUE__) == OB_RDP_LEVEL_2)) |
| |
| #define IS_OB_USER_TYPE(__VALUE__) ((((__VALUE__) & OB_USER_ALL) != 0U) && \ |
| (((__VALUE__) & ~OB_USER_ALL) == 0U)) |
| |
| #define IS_OB_USER_CONFIG(__TYPE__, __VALUE__) ((((__TYPE__) & OB_USER_BOR_LEV) == OB_USER_BOR_LEV) \ |
| ? ((((__VALUE__) & ~(OB_USER_ALL & ~OB_USER_BOR_LEV)) == OB_BOR_LEVEL_0) || \ |
| (((__VALUE__) & ~(OB_USER_ALL & ~OB_USER_BOR_LEV)) == OB_BOR_LEVEL_1) || \ |
| (((__VALUE__) & ~(OB_USER_ALL & ~OB_USER_BOR_LEV)) == OB_BOR_LEVEL_2) || \ |
| (((__VALUE__) & ~(OB_USER_ALL & ~OB_USER_BOR_LEV)) == OB_BOR_LEVEL_3) || \ |
| (((__VALUE__) & ~(OB_USER_ALL & ~OB_USER_BOR_LEV)) == OB_BOR_LEVEL_4)) \ |
| : ((((__TYPE__) & OB_USER_AGC_TRIM) == OB_USER_AGC_TRIM) \ |
| ? ((((__VALUE__) & ~(OB_USER_ALL & ~OB_USER_AGC_TRIM)) == OB_AGC_TRIM_0) || \ |
| (((__VALUE__) & ~(OB_USER_ALL & ~OB_USER_AGC_TRIM)) == OB_AGC_TRIM_1) || \ |
| (((__VALUE__) & ~(OB_USER_ALL & ~OB_USER_AGC_TRIM)) == OB_AGC_TRIM_2) || \ |
| (((__VALUE__) & ~(OB_USER_ALL & ~OB_USER_AGC_TRIM)) == OB_AGC_TRIM_3) || \ |
| (((__VALUE__) & ~(OB_USER_ALL & ~OB_USER_AGC_TRIM)) == OB_AGC_TRIM_4) || \ |
| (((__VALUE__) & ~(OB_USER_ALL & ~OB_USER_AGC_TRIM)) == OB_AGC_TRIM_5) || \ |
| (((__VALUE__) & ~(OB_USER_ALL & ~OB_USER_AGC_TRIM)) == OB_AGC_TRIM_6) || \ |
| (((__VALUE__) & ~(OB_USER_ALL & ~OB_USER_AGC_TRIM)) == OB_AGC_TRIM_7)) \ |
| : ((~(__TYPE__) & (__VALUE__)) == 0U))) |
| |
| #define IS_OB_USER_AGC_TRIMMING(__VALUE__) (((__VALUE__) == OB_AGC_TRIM_0) || ((__VALUE__) == OB_AGC_TRIM_1) || \ |
| ((__VALUE__) == OB_AGC_TRIM_2) || ((__VALUE__) == OB_AGC_TRIM_3) || \ |
| ((__VALUE__) == OB_AGC_TRIM_4) || ((__VALUE__) == OB_AGC_TRIM_5) || \ |
| ((__VALUE__) == OB_AGC_TRIM_6) || ((__VALUE__) == OB_AGC_TRIM_7)) |
| |
| #define IS_OB_USER_BOR_LEVEL(__VALUE__) (((__VALUE__) == OB_BOR_LEVEL_0) || ((__VALUE__) == OB_BOR_LEVEL_1) || \ |
| ((__VALUE__) == OB_BOR_LEVEL_2) || ((__VALUE__) == OB_BOR_LEVEL_3) || \ |
| ((__VALUE__) == OB_BOR_LEVEL_4)) |
| |
| #define IS_OB_PCROP_CONFIG(__VALUE__) (((__VALUE__) & ~(OB_PCROP_ZONE_A | OB_PCROP_ZONE_B | OB_PCROP_RDP_ERASE)) == 0U) |
| |
| #define IS_OB_IPCC_BUF_ADDR(__VALUE__) (IS_OB_SBRSA_START_ADDR(__VALUE__) || IS_OB_SNBRSA_START_ADDR(__VALUE__)) |
| |
| #define IS_OB_BOOT_VECTOR_ADDR(__VALUE__) ((((__VALUE__) >= FLASH_BASE) && ((__VALUE__) <= (FLASH_BASE + FLASH_SIZE - 1U))) || \ |
| (((__VALUE__) >= SRAM1_BASE) && ((__VALUE__) <= (SRAM1_BASE + SRAM1_SIZE - 1U))) || \ |
| (((__VALUE__) >= SRAM2A_BASE) && ((__VALUE__) <= (SRAM2A_BASE + SRAM2A_SIZE - 1U))) || \ |
| (((__VALUE__) >= SRAM2B_BASE) && ((__VALUE__) <= (SRAM2B_BASE + SRAM2B_SIZE - 1U)))) |
| |
| #define IS_OB_BOOT_REGION(__VALUE__) (((__VALUE__) == OB_C2_BOOT_FROM_FLASH) || ((__VALUE__) == OB_C2_BOOT_FROM_SRAM)) |
| |
| #define IS_OB_SECURE_CONFIG(__VALUE__) (((__VALUE__) & ~(OB_SECURE_CONFIG_MEMORY | OB_SECURE_CONFIG_BOOT_RESET)) == 0U) |
| |
| #define IS_FLASH_LATENCY(__VALUE__) (((__VALUE__) == FLASH_LATENCY_0) || \ |
| ((__VALUE__) == FLASH_LATENCY_1) || \ |
| ((__VALUE__) == FLASH_LATENCY_2) || \ |
| ((__VALUE__) == FLASH_LATENCY_3)) |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| #ifdef __cplusplus |
| } |
| #endif |
| |
| #endif /* STM32WBxx_HAL_FLASH_H */ |
| |
| /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |
