| /** |
| ****************************************************************************** |
| * @file stm32wbxx_hal_pwr.h |
| * @author MCD Application Team |
| * @brief Header file of PWR HAL module. |
| ****************************************************************************** |
| * @attention |
| * |
| * <h2><center>© Copyright (c) 2019 STMicroelectronics. |
| * All rights reserved.</center></h2> |
| * |
| * This software component is licensed by ST under BSD 3-Clause license, |
| * the "License"; You may not use this file except in compliance with the |
| * License. You may obtain a copy of the License at: |
| * opensource.org/licenses/BSD-3-Clause |
| * |
| ****************************************************************************** |
| */ |
| |
| /* Define to prevent recursive inclusion -------------------------------------*/ |
| #ifndef STM32WBxx_HAL_PWR_H |
| #define STM32WBxx_HAL_PWR_H |
| |
| #ifdef __cplusplus |
| extern "C" { |
| #endif |
| |
| /* Includes ------------------------------------------------------------------*/ |
| #include "stm32wbxx_hal_def.h" |
| |
| /* Include low level driver */ |
| #include "stm32wbxx_ll_pwr.h" |
| #include "stm32wbxx_ll_exti.h" |
| |
| /** @addtogroup STM32WBxx_HAL_Driver |
| * @{ |
| */ |
| |
| /** @defgroup PWR PWR |
| * @brief PWR HAL module driver |
| * @{ |
| */ |
| |
| /* Exported types ------------------------------------------------------------*/ |
| /** @defgroup PWR_Exported_Types PWR Exported Types |
| * @{ |
| */ |
| |
| /** |
| * @brief PWR PVD configuration structure definition |
| */ |
| typedef struct |
| { |
| uint32_t PVDLevel; /*!< PVDLevel: Specifies the PVD detection level. |
| This parameter can be a value of @ref PWR_PVD_detection_level. */ |
| |
| uint32_t Mode; /*!< Mode: Specifies the operating mode for the selected pins. |
| This parameter can be a value of @ref PWR_PVD_Mode. */ |
| }PWR_PVDTypeDef; |
| |
| /** |
| * @} |
| */ |
| |
| /* Exported constants --------------------------------------------------------*/ |
| /** @defgroup PWR_Exported_Constants PWR Exported Constants |
| * @{ |
| */ |
| |
| /** @defgroup PWR_PVD_detection_level Power Voltage Detector Level selection |
| * @note Refer datasheet for selection voltage value |
| * @{ |
| */ |
| #define PWR_PVDLEVEL_0 (0x00000000U) /*!< PVD threshold around 2.0 V */ |
| #define PWR_PVDLEVEL_1 ( PWR_CR2_PLS_0) /*!< PVD threshold around 2.2 V */ |
| #define PWR_PVDLEVEL_2 ( PWR_CR2_PLS_1 ) /*!< PVD threshold around 2.4 V */ |
| #define PWR_PVDLEVEL_3 ( PWR_CR2_PLS_1 | PWR_CR2_PLS_0) /*!< PVD threshold around 2.5 V */ |
| #define PWR_PVDLEVEL_4 (PWR_CR2_PLS_2 ) /*!< PVD threshold around 2.6 V */ |
| #define PWR_PVDLEVEL_5 (PWR_CR2_PLS_2 | PWR_CR2_PLS_0) /*!< PVD threshold around 2.8 V */ |
| #define PWR_PVDLEVEL_6 (PWR_CR2_PLS_2 | PWR_CR2_PLS_1 ) /*!< PVD threshold around 2.9 V */ |
| #define PWR_PVDLEVEL_7 (PWR_CR2_PLS_2 | PWR_CR2_PLS_1 | PWR_CR2_PLS_0) /*!< External input analog voltage (compared internally to VREFINT) */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup PWR_PVD_Mode PWR PVD interrupt and event mode |
| * @{ |
| */ |
| /* Note: On STM32WB serie, power PVD event is not available on AIEC lines */ |
| /* (only interruption is available through AIEC line 16). */ |
| #define PWR_PVD_MODE_NORMAL (0x00000000U) /*!< Basic mode is used */ |
| |
| #define PWR_PVD_MODE_IT_RISING (PVD_MODE_IT | PVD_RISING_EDGE) /*!< External Interrupt Mode with Rising edge trigger detection */ |
| #define PWR_PVD_MODE_IT_FALLING (PVD_MODE_IT | PVD_FALLING_EDGE) /*!< External Interrupt Mode with Falling edge trigger detection */ |
| #define PWR_PVD_MODE_IT_RISING_FALLING (PVD_MODE_IT | PVD_RISING_FALLING_EDGE) /*!< External Interrupt Mode with Rising/Falling edge trigger detection */ |
| /** |
| * @} |
| */ |
| |
| /* Note: On STM32WB serie, power PVD event is not available on AIEC lines */ |
| /* (only interruption is available through AIEC line 16). */ |
| |
| /** @defgroup PWR_Low_Power_Mode_Selection PWR Low Power Mode Selection |
| * @{ |
| */ |
| #define PWR_LOWPOWERMODE_STOP0 (0x00000000u) /*!< Stop 0: stop mode with main regulator */ |
| #define PWR_LOWPOWERMODE_STOP1 (PWR_CR1_LPMS_0) /*!< Stop 1: stop mode with low power regulator */ |
| #define PWR_LOWPOWERMODE_STOP2 (PWR_CR1_LPMS_1) /*!< Stop 2: stop mode with low power regulator and VDD12I interruptible digital core domain supply OFF (less peripherals activated than low power mode stop 1 to reduce power consumption)*/ |
| #define PWR_LOWPOWERMODE_STANDBY (PWR_CR1_LPMS_0 | PWR_CR1_LPMS_1) /*!< Standby mode */ |
| #define PWR_LOWPOWERMODE_SHUTDOWN (PWR_CR1_LPMS_2) /*!< Shutdown mode */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup PWR_Regulator_state_in_SLEEP_STOP_mode PWR regulator mode |
| * @{ |
| */ |
| #define PWR_MAINREGULATOR_ON (0x00000000U) /*!< Regulator in main mode */ |
| #define PWR_LOWPOWERREGULATOR_ON (PWR_CR1_LPR) /*!< Regulator in low-power mode */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup PWR_SLEEP_mode_entry PWR SLEEP mode entry |
| * @{ |
| */ |
| #define PWR_SLEEPENTRY_WFI ((uint8_t)0x01) /*!< Wait For Interruption instruction to enter Sleep mode */ |
| #define PWR_SLEEPENTRY_WFE ((uint8_t)0x02) /*!< Wait For Event instruction to enter Sleep mode */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup PWR_STOP_mode_entry PWR STOP mode entry |
| * @{ |
| */ |
| #define PWR_STOPENTRY_WFI ((uint8_t)0x01) /*!< Wait For Interruption instruction to enter Stop mode */ |
| #define PWR_STOPENTRY_WFE ((uint8_t)0x02) /*!< Wait For Event instruction to enter Stop mode */ |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Private define ------------------------------------------------------------*/ |
| /** @defgroup PWR_Private_Defines PWR Private Defines |
| * @{ |
| */ |
| |
| /** @defgroup PWR_PVD_EXTI_LINE PWR PVD external interrupt line |
| * @{ |
| */ |
| #define PWR_EXTI_LINE_PVD (LL_EXTI_LINE_16) /*!< External interrupt line 16 Connected to the PWR PVD */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup PWR_PVD_Mode_Mask PWR PVD Mode Mask |
| * @{ |
| */ |
| /* Note: On STM32WB serie, power PVD event is not available on AIEC lines */ |
| /* (only interruption is available through AIEC line 16). */ |
| #define PVD_MODE_IT (0x00010000U) /*!< Mask for interruption yielded by PVD threshold crossing */ |
| #define PVD_RISING_EDGE (0x00000001U) /*!< Mask for rising edge set as PVD trigger */ |
| #define PVD_FALLING_EDGE (0x00000002U) /*!< Mask for falling edge set as PVD trigger */ |
| #define PVD_RISING_FALLING_EDGE (0x00000003U) /*!< Mask for rising and falling edges set as PVD trigger */ |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Exported macros -----------------------------------------------------------*/ |
| /** @defgroup PWR_Exported_Macros PWR Exported Macros |
| * @{ |
| */ |
| /** @brief Check whether or not a specific PWR flag is set. |
| * @param __FLAG__ specifies the flag to check. |
| * This parameter can be one of the following values: |
| * |
| * /--------------------------------SR1-------------------------------/ |
| * @arg @ref PWR_FLAG_WUF1 Wake Up Flag 1. Indicates that a wakeup event |
| * was received from the WKUP pin 1. |
| * @arg @ref PWR_FLAG_WUF2 Wake Up Flag 2. Indicates that a wakeup event |
| * was received from the WKUP pin 2. |
| * @arg @ref PWR_FLAG_WUF3 Wake Up Flag 3. Indicates that a wakeup event |
| * was received from the WKUP pin 3. |
| * @arg @ref PWR_FLAG_WUF4 Wake Up Flag 4. Indicates that a wakeup event |
| * was received from the WKUP pin 4. |
| * @arg @ref PWR_FLAG_WUF5 Wake Up Flag 5. Indicates that a wakeup event |
| * was received from the WKUP pin 5. |
| * |
| * @arg @ref PWR_FLAG_BHWF BLE_Host WakeUp Flag |
| * @arg @ref PWR_FLAG_FRCBYPI SMPS Forced in Bypass Interrupt Flag |
| * @arg @ref PWR_FLAG_RFPHASEI Radio Phase Interrupt Flag |
| * @arg @ref PWR_FLAG_BLEACTI BLE Activity Interrupt Flag |
| * @arg @ref PWR_FLAG_802ACTI 802.15.4 Activity Interrupt Flag |
| * @arg @ref PWR_FLAG_HOLDC2I CPU2 on-Hold Interrupt Flag |
| * @arg @ref PWR_FLAG_WUFI Wake-Up Flag Internal. Set when a wakeup is detected on |
| * the internal wakeup line. |
| * |
| * @arg @ref PWR_FLAG_SMPSRDYF SMPS Ready Flag |
| * @arg @ref PWR_FLAG_SMPSBYPF SMPS Bypass Flag |
| * |
| * /--------------------------------SR2-------------------------------/ |
| * @arg @ref PWR_FLAG_REGLPS Low Power Regulator Started. Indicates whether or not the |
| * low-power regulator is ready. |
| * @arg @ref PWR_FLAG_REGLPF Low Power Regulator Flag. Indicates whether the |
| * regulator is ready in main mode or is in low-power mode. |
| * |
| * @arg @ref PWR_FLAG_VOSF Voltage Scaling Flag. Indicates whether the regulator is ready |
| * in the selected voltage range or is still changing to the required voltage level. |
| * @arg @ref PWR_FLAG_PVDO Power Voltage Detector Output. Indicates whether VDD voltage is |
| * below or above the selected PVD threshold. |
| * |
| * @arg @ref PWR_FLAG_PVMO1 Peripheral Voltage Monitoring Output 1. Indicates whether VDDUSB voltage is |
| * is below or above PVM1 threshold (applicable when USB feature is supported). |
| * @arg @ref PWR_FLAG_PVMO3 Peripheral Voltage Monitoring Output 3. Indicates whether VDDA voltage is |
| * is below or above PVM3 threshold. |
| * |
| * /----------------------------EXTSCR--------------------------/ |
| * @arg @ref PWR_FLAG_STOP System Stop Flag for CPU1. |
| * @arg @ref PWR_FLAG_SB System Standby Flag for CPU1. |
| * |
| * @arg @ref PWR_FLAG_C2STOP System Stop Flag for CPU2. |
| * @arg @ref PWR_FLAG_C2SB System Standby Flag for CPU2. |
| * |
| * @arg @ref PWR_FLAG_CRITICAL_RF_PHASE Critical radio system phase flag. |
| * |
| * @arg @ref PWR_FLAG_C1DEEPSLEEP CPU1 DeepSleep Flag. |
| * @arg @ref PWR_FLAG_C2DEEPSLEEP CPU2 DeepSleep Flag. |
| * |
| * @retval The new state of __FLAG__ (TRUE or FALSE). |
| */ |
| #define __HAL_PWR_GET_FLAG(__FLAG__) ((((__FLAG__) & PWR_FLAG_REG_MASK) == PWR_FLAG_REG_SR1) ? \ |
| ( \ |
| PWR->SR1 & (1UL << ((__FLAG__) & 31UL)) \ |
| ) \ |
| : \ |
| ( \ |
| (((__FLAG__) & PWR_FLAG_REG_MASK) == PWR_FLAG_REG_SR2) ? \ |
| ( \ |
| PWR->SR2 & (1UL << ((__FLAG__) & 31UL)) \ |
| ) \ |
| : \ |
| ( \ |
| PWR->EXTSCR & (1UL << ((__FLAG__) & 31UL)) \ |
| ) \ |
| ) \ |
| ) |
| |
| /** @brief Clear a specific PWR flag. |
| * @note Clearing of flags {PWR_FLAG_STOP, PWR_FLAG_SB} |
| * and flags {PWR_FLAG_C2STOP, PWR_FLAG_C2SB} are grouped: |
| * clearing of one flag also clears the other one. |
| * @param __FLAG__ specifies the flag to clear. |
| * This parameter can be one of the following values: |
| * |
| * /--------------------------------SCR (SRR)------------------------------/ |
| * @arg @ref PWR_FLAG_WUF1 Wake Up Flag 1. Indicates that a wakeup event |
| * was received from the WKUP pin 1. |
| * @arg @ref PWR_FLAG_WUF2 Wake Up Flag 2. Indicates that a wakeup event |
| * was received from the WKUP pin 2. |
| * @arg @ref PWR_FLAG_WUF3 Wake Up Flag 3. Indicates that a wakeup event |
| * was received from the WKUP pin 3. |
| * @arg @ref PWR_FLAG_WUF4 Wake Up Flag 4. Indicates that a wakeup event |
| * was received from the WKUP pin 4. |
| * @arg @ref PWR_FLAG_WUF5 Wake Up Flag 5. Indicates that a wakeup event |
| * was received from the WKUP pin 5. |
| * @arg @ref PWR_FLAG_WU Encompasses all five Wake Up Flags. |
| * |
| * @arg @ref PWR_FLAG_BHWF Clear BLE_Host Wakeup Flag. |
| * @arg @ref PWR_FLAG_FRCBYPI Clear SMPS Forced in Bypass Interrupt Flag. |
| * @arg @ref PWR_FLAG_RFPHASEI RF Phase Interrupt Clear. |
| * @arg @ref PWR_FLAG_BLEACTI BLE Activity Interrupt Clear. |
| * @arg @ref PWR_FLAG_802ACTI 802.15.4. Activity Interrupt Clear. |
| * @arg @ref PWR_FLAG_HOLDC2I CPU2 on-Hold Interrupt Clear. |
| * |
| * /----------------------------EXTSCR--------------------------/ |
| * @arg @ref PWR_FLAG_STOP System Stop Flag for CPU1. |
| * @arg @ref PWR_FLAG_SB System Standby Flag for CPU1. |
| * |
| * @arg @ref PWR_FLAG_C2STOP System Stop Flag for CPU2. |
| * @arg @ref PWR_FLAG_C2SB System Standby Flag for CPU2. |
| * |
| * @arg @ref PWR_FLAG_CRITICAL_RF_PHASE RF phase Flag. |
| * |
| * @retval None |
| */ |
| #define __HAL_PWR_CLEAR_FLAG(__FLAG__) ((((__FLAG__) & PWR_FLAG_REG_MASK) == PWR_FLAG_REG_EXTSCR) ? \ |
| ( \ |
| PWR->EXTSCR = (1UL << (((__FLAG__) & PWR_FLAG_EXTSCR_CLR_MASK) >> PWR_FLAG_EXTSCR_CLR_POS)) \ |
| ) \ |
| : \ |
| ( \ |
| (((__FLAG__)) == PWR_FLAG_WU) ? \ |
| (PWR->SCR = PWR_SCR_CWUF) : \ |
| (PWR->SCR = (1UL << ((__FLAG__) & 31UL))) \ |
| ) \ |
| ) |
| |
| /** |
| * @brief Enable the PVD Extended Interrupt C1 Line. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVD_EXTI_ENABLE_IT() LL_EXTI_EnableIT_0_31(PWR_EXTI_LINE_PVD) |
| |
| /** |
| * @brief Enable the PVD Extended Interrupt C2 Line. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVD_EXTIC2_ENABLE_IT() LL_C2_EXTI_EnableIT_0_31(PWR_EXTI_LINE_PVD) |
| |
| |
| /** |
| * @brief Disable the PVD Extended Interrupt C1 Line. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVD_EXTI_DISABLE_IT() LL_EXTI_DisableIT_0_31(PWR_EXTI_LINE_PVD) |
| |
| /** |
| * @brief Disable the PVD Extended Interrupt C2 Line. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVD_EXTIC2_DISABLE_IT() LL_C2_EXTI_DisableIT_0_31(PWR_EXTI_LINE_PVD) |
| |
| /* Note: On STM32WB serie, power PVD event is not available on AIEC lines */ |
| /* (only interruption is available through AIEC line 16). */ |
| |
| /** |
| * @brief Enable the PVD Extended Interrupt Rising Trigger. |
| * @note PVD flag polarity is inverted compared to EXTI line, therefore |
| * EXTI rising and falling logic edges are inverted versus PVD voltage edges. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE() LL_EXTI_EnableRisingTrig_0_31(PWR_EXTI_LINE_PVD) |
| |
| /** |
| * @brief Disable the PVD Extended Interrupt Rising Trigger. |
| * @note PVD flag polarity is inverted compared to EXTI line, therefore |
| * EXTI rising and falling logic edges are inverted versus PVD voltage edges. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE() LL_EXTI_DisableFallingTrig_0_31(PWR_EXTI_LINE_PVD) |
| |
| /** |
| * @brief Enable the PVD Extended Interrupt Falling Trigger. |
| * @note PVD flag polarity is inverted compared to EXTI line, therefore |
| * EXTI rising and falling logic edges are inverted versus PVD voltage edges. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE() LL_EXTI_EnableFallingTrig_0_31(PWR_EXTI_LINE_PVD) |
| |
| |
| /** |
| * @brief Disable the PVD Extended Interrupt Falling Trigger. |
| * @note PVD flag polarity is inverted compared to EXTI line, therefore |
| * EXTI rising and falling logic edges are inverted versus PVD voltage edges. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE() LL_EXTI_DisableRisingTrig_0_31(PWR_EXTI_LINE_PVD) |
| |
| |
| /** |
| * @brief Enable the PVD Extended Interrupt Rising & Falling Trigger. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVD_EXTI_ENABLE_RISING_FALLING_EDGE() \ |
| do { \ |
| __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE(); \ |
| __HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE(); \ |
| } while(0) |
| |
| /** |
| * @brief Disable the PVD Extended Interrupt Rising & Falling Trigger. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVD_EXTI_DISABLE_RISING_FALLING_EDGE() \ |
| do { \ |
| __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE(); \ |
| __HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE(); \ |
| } while(0) |
| |
| /** |
| * @brief Generate a Software interrupt on selected EXTI line. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVD_EXTI_GENERATE_SWIT() LL_EXTI_GenerateSWI_0_31(PWR_EXTI_LINE_PVD) |
| |
| /** |
| * @brief Check whether or not the PVD EXTI interrupt flag is set. |
| * @retval EXTI PVD Line Status. |
| */ |
| #define __HAL_PWR_PVD_EXTI_GET_FLAG() LL_EXTI_ReadFlag_0_31(PWR_EXTI_LINE_PVD) |
| |
| /** |
| * @brief Clear the PVD EXTI interrupt flag. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVD_EXTI_CLEAR_FLAG() LL_EXTI_ClearFlag_0_31(PWR_EXTI_LINE_PVD) |
| |
| /** |
| * @} |
| */ |
| |
| |
| /* Private macros --------------------------------------------------------*/ |
| /** @defgroup PWR_Private_Macros PWR Private Macros |
| * @{ |
| */ |
| |
| #define IS_PWR_PVD_LEVEL(LEVEL) (((LEVEL) == PWR_PVDLEVEL_0) || ((LEVEL) == PWR_PVDLEVEL_1)|| \ |
| ((LEVEL) == PWR_PVDLEVEL_2) || ((LEVEL) == PWR_PVDLEVEL_3)|| \ |
| ((LEVEL) == PWR_PVDLEVEL_4) || ((LEVEL) == PWR_PVDLEVEL_5)|| \ |
| ((LEVEL) == PWR_PVDLEVEL_6) || ((LEVEL) == PWR_PVDLEVEL_7)) |
| |
| #define IS_PWR_PVD_MODE(MODE) (((MODE) == PWR_PVD_MODE_NORMAL) ||\ |
| ((MODE) == PWR_PVD_MODE_IT_RISING) ||\ |
| ((MODE) == PWR_PVD_MODE_IT_FALLING) ||\ |
| ((MODE) == PWR_PVD_MODE_IT_RISING_FALLING)) |
| |
| |
| |
| #define IS_PWR_REGULATOR(REGULATOR) (((REGULATOR) == PWR_MAINREGULATOR_ON) || \ |
| ((REGULATOR) == PWR_LOWPOWERREGULATOR_ON)) |
| |
| |
| #define IS_PWR_SLEEP_ENTRY(ENTRY) (((ENTRY) == PWR_SLEEPENTRY_WFI) || \ |
| ((ENTRY) == PWR_SLEEPENTRY_WFE)) |
| |
| #define IS_PWR_STOP_ENTRY(ENTRY) (((ENTRY) == PWR_STOPENTRY_WFI) || \ |
| ((ENTRY) == PWR_STOPENTRY_WFE)) |
| /** |
| * @} |
| */ |
| |
| /* Include PWR HAL Extended module */ |
| #include "stm32wbxx_hal_pwr_ex.h" |
| |
| /* Exported functions --------------------------------------------------------*/ |
| /** @defgroup PWR_Exported_Functions PWR Exported Functions |
| * @{ |
| */ |
| |
| /** @defgroup PWR_Exported_Functions_Group1 Initialization and de-initialization functions |
| * @{ |
| */ |
| |
| /* Initialization and de-initialization functions *******************************/ |
| void HAL_PWR_DeInit(void); |
| |
| void HAL_PWR_EnableBkUpAccess(void); |
| void HAL_PWR_DisableBkUpAccess(void); |
| /** |
| * @} |
| */ |
| |
| /** @defgroup PWR_Exported_Functions_Group2 Peripheral Control functions |
| * @{ |
| */ |
| /* Peripheral Control functions ************************************************/ |
| HAL_StatusTypeDef HAL_PWR_ConfigPVD(PWR_PVDTypeDef *sConfigPVD); |
| void HAL_PWR_EnablePVD(void); |
| void HAL_PWR_DisablePVD(void); |
| |
| /* WakeUp pins configuration functions ****************************************/ |
| void HAL_PWR_EnableWakeUpPin(uint32_t WakeUpPinPolarity); |
| void HAL_PWR_DisableWakeUpPin(uint32_t WakeUpPinx); |
| |
| /* Low Power modes configuration functions ************************************/ |
| void HAL_PWR_EnterSTOPMode(uint32_t Regulator, uint8_t STOPEntry); |
| void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry); |
| void HAL_PWR_EnterSTANDBYMode(void); |
| |
| void HAL_PWR_PVDCallback(void); |
| void HAL_PWR_EnableSleepOnExit(void); |
| void HAL_PWR_DisableSleepOnExit(void); |
| |
| void HAL_PWR_EnableSEVOnPend(void); |
| void HAL_PWR_DisableSEVOnPend(void); |
| |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| #ifdef __cplusplus |
| } |
| #endif |
| |
| |
| #endif /* STM32WBxx_HAL_PWR_H */ |
| |
| /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |
