| /** |
| ****************************************************************************** |
| * @file stm32wlxx_hal_conf.h |
| * @author MCD Application Team |
| * @brief HAL configuration file. |
| ****************************************************************************** |
| * @attention |
| * |
| * <h2><center>© Copyright (c) 2020 STMicroelectronics. |
| * All rights reserved.</center></h2> |
| * |
| * This software component is licensed by ST under BSD 3-Clause license, |
| * the "License"; You may not use this file except in compliance with the |
| * License. You may obtain a copy of the License at: |
| * opensource.org/licenses/BSD-3-Clause |
| * |
| ****************************************************************************** |
| */ |
| |
| /* Define to prevent recursive inclusion -------------------------------------*/ |
| #ifndef STM32WLxx_HAL_CONF_H |
| #define STM32WLxx_HAL_CONF_H |
| |
| #ifdef __cplusplus |
| extern "C" { |
| #endif |
| |
| /* Exported types ------------------------------------------------------------*/ |
| /* Exported constants --------------------------------------------------------*/ |
| |
| /* ########################## Module Selection ############################## */ |
| /** |
| * @brief This is the list of modules to be used in the HAL driver |
| */ |
| #define HAL_MODULE_ENABLED |
| #define HAL_ADC_MODULE_ENABLED |
| #define HAL_COMP_MODULE_ENABLED |
| #define HAL_CRC_MODULE_ENABLED |
| #define HAL_CRYP_MODULE_ENABLED |
| #define HAL_DAC_MODULE_ENABLED |
| #define HAL_GTZC_MODULE_ENABLED |
| #define HAL_HSEM_MODULE_ENABLED |
| #define HAL_I2C_MODULE_ENABLED |
| #define HAL_I2S_MODULE_ENABLED |
| #define HAL_IPCC_MODULE_ENABLED |
| #define HAL_IRDA_MODULE_ENABLED |
| #define HAL_IWDG_MODULE_ENABLED |
| #define HAL_LPTIM_MODULE_ENABLED |
| #define HAL_PKA_MODULE_ENABLED |
| #define HAL_RNG_MODULE_ENABLED |
| #define HAL_RTC_MODULE_ENABLED |
| #define HAL_SMARTCARD_MODULE_ENABLED |
| #define HAL_SMBUS_MODULE_ENABLED |
| #define HAL_SPI_MODULE_ENABLED |
| #define HAL_SUBGHZ_MODULE_ENABLED |
| #define HAL_TIM_MODULE_ENABLED |
| #define HAL_UART_MODULE_ENABLED |
| #define HAL_USART_MODULE_ENABLED |
| #define HAL_WWDG_MODULE_ENABLED |
| #define HAL_EXTI_MODULE_ENABLED |
| #define HAL_CORTEX_MODULE_ENABLED |
| #define HAL_DMA_MODULE_ENABLED |
| #define HAL_FLASH_MODULE_ENABLED |
| #define HAL_GPIO_MODULE_ENABLED |
| #define HAL_PWR_MODULE_ENABLED |
| #define HAL_RCC_MODULE_ENABLED |
| |
| /* ########################## Register Callbacks selection ############################## */ |
| /** |
| * @brief This is the list of modules where register callback can be used |
| */ |
| #define USE_HAL_ADC_REGISTER_CALLBACKS 0u |
| #define USE_HAL_COMP_REGISTER_CALLBACKS 0u |
| #define USE_HAL_CRYP_REGISTER_CALLBACKS 0u |
| #define USE_HAL_DAC_REGISTER_CALLBACKS 0u |
| #define USE_HAL_I2C_REGISTER_CALLBACKS 0u |
| #define USE_HAL_I2S_REGISTER_CALLBACKS 0u |
| #define USE_HAL_IRDA_REGISTER_CALLBACKS 0u |
| #define USE_HAL_LPTIM_REGISTER_CALLBACKS 0u |
| #define USE_HAL_PKA_REGISTER_CALLBACKS 0u |
| #define USE_HAL_RNG_REGISTER_CALLBACKS 0u |
| #define USE_HAL_RTC_REGISTER_CALLBACKS 0u |
| #define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0u |
| #define USE_HAL_SMBUS_REGISTER_CALLBACKS 0u |
| #define USE_HAL_SPI_REGISTER_CALLBACKS 0u |
| #define USE_HAL_SUBGHZ_REGISTER_CALLBACKS 0u |
| #define USE_HAL_TIM_REGISTER_CALLBACKS 0u |
| #define USE_HAL_UART_REGISTER_CALLBACKS 0u |
| #define USE_HAL_USART_REGISTER_CALLBACKS 0u |
| #define USE_HAL_WWDG_REGISTER_CALLBACKS 0u |
| |
| /* ########################## Oscillator Values adaptation ####################*/ |
| /** |
| * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. |
| * This value is used by the RCC HAL module to compute the system frequency |
| * (when HSE is used as system clock source, directly or through the PLL). |
| */ |
| |
| #if !defined (HSE_VALUE) |
| #define HSE_VALUE 32000000UL /*!< Value of the External oscillator in Hz */ |
| #endif /* HSE_VALUE */ |
| |
| #if !defined (HSE_STARTUP_TIMEOUT) |
| #define HSE_STARTUP_TIMEOUT 100UL /*!< Time out for HSE start up, in ms */ |
| #endif /* HSE_STARTUP_TIMEOUT */ |
| |
| /** |
| * @brief Internal Multiple Speed oscillator (MSI) default value. |
| * This value is the default MSI range value after Reset. |
| */ |
| #if !defined (MSI_VALUE) |
| #define MSI_VALUE 4000000UL /*!< Value of the Internal oscillator in Hz*/ |
| #endif /* MSI_VALUE */ |
| |
| /** |
| * @brief Internal High Speed oscillator (HSI) value. |
| * This value is used by the RCC HAL module to compute the system frequency |
| * (when HSI is used as system clock source, directly or through the PLL). |
| */ |
| #if !defined (HSI_VALUE) |
| #define HSI_VALUE 16000000UL /*!< Value of the Internal oscillator in Hz*/ |
| #endif /* HSI_VALUE */ |
| |
| /** |
| * @brief Internal Low Speed oscillator (LSI) value. |
| */ |
| #if !defined (LSI_VALUE) |
| #define LSI_VALUE 32000UL /*!< LSI Typical Value in Hz*/ |
| #endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz |
| The real value may vary depending on the variations |
| in voltage and temperature. */ |
| |
| /** |
| * @brief External Low Speed oscillator (LSE) value. |
| * This value is used by the UART, RTC HAL module to compute the system frequency |
| */ |
| #if !defined (LSE_VALUE) |
| #define LSE_VALUE 32768UL /*!< Value of the External oscillator in Hz*/ |
| #endif /* LSE_VALUE */ |
| |
| /** |
| * @brief Internal Multiple Speed oscillator (HSI48) default value. |
| * This value is the default HSI48 range value after Reset. |
| */ |
| #if !defined (HSI48_VALUE) |
| #define HSI48_VALUE 48000000UL /*!< Value of the Internal oscillator in Hz*/ |
| #endif /* HSI48_VALUE */ |
| |
| #if !defined (LSE_STARTUP_TIMEOUT) |
| #define LSE_STARTUP_TIMEOUT 5000UL /*!< Time out for LSE start up, in ms */ |
| #endif /* LSE_STARTUP_TIMEOUT */ |
| |
| |
| /* Tip: To avoid modifying this file each time you need to use different HSE, |
| === you can define the HSE value in your toolchain compiler preprocessor. */ |
| |
| /* ########################### System Configuration ######################### */ |
| /** |
| * @brief This is the HAL system configuration section |
| */ |
| #define VDD_VALUE 3300U /*!< Value of VDD in mv */ |
| #define TICK_INT_PRIORITY ((1uL <<__NVIC_PRIO_BITS) - 1uL) /*!< tick interrupt priority (lowest by default) */ |
| #define USE_RTOS 0U |
| #define PREFETCH_ENABLE 0U |
| #define INSTRUCTION_CACHE_ENABLE 1U |
| #define DATA_CACHE_ENABLE 1U |
| |
| /* ########################## Assert Selection ############################## */ |
| /** |
| * @brief Uncomment the line below to expanse the "assert_param" macro in the |
| * HAL drivers code |
| */ |
| /* #define USE_FULL_ASSERT 1 */ |
| |
| /* ################## SPI peripheral configuration ########################## */ |
| |
| /* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver |
| * Activated: CRC code is present inside driver |
| * Deactivated: CRC code cleaned from driver |
| */ |
| |
| #define USE_SPI_CRC 1U |
| |
| /* ################## CRYP peripheral configuration ########################## */ |
| |
| #define USE_HAL_CRYP_SUSPEND_RESUME 1U |
| |
| |
| /* Includes ------------------------------------------------------------------*/ |
| /** |
| * @brief Include module's header file |
| */ |
| #ifdef HAL_DMA_MODULE_ENABLED |
| #include "stm32wlxx_hal_dma.h" |
| #endif /* HAL_DMA_MODULE_ENABLED */ |
| |
| #ifdef HAL_ADC_MODULE_ENABLED |
| #include "stm32wlxx_hal_adc.h" |
| #endif /* HAL_ADC_MODULE_ENABLED */ |
| |
| #ifdef HAL_COMP_MODULE_ENABLED |
| #include "stm32wlxx_hal_comp.h" |
| #endif /* HAL_COMP_MODULE_ENABLED */ |
| |
| #ifdef HAL_CORTEX_MODULE_ENABLED |
| #include "stm32wlxx_hal_cortex.h" |
| #endif /* HAL_CORTEX_MODULE_ENABLED */ |
| |
| #ifdef HAL_CRC_MODULE_ENABLED |
| #include "stm32wlxx_hal_crc.h" |
| #endif /* HAL_CRC_MODULE_ENABLED */ |
| |
| #ifdef HAL_CRYP_MODULE_ENABLED |
| #include "stm32wlxx_hal_cryp.h" |
| #endif /* HAL_CRYP_MODULE_ENABLED */ |
| |
| #ifdef HAL_DAC_MODULE_ENABLED |
| #include "stm32wlxx_hal_dac.h" |
| #endif /* HAL_DAC_MODULE_ENABLED */ |
| |
| #ifdef HAL_EXTI_MODULE_ENABLED |
| #include "stm32wlxx_hal_exti.h" |
| #endif /* HAL_EXTI_MODULE_ENABLED */ |
| |
| #ifdef HAL_FLASH_MODULE_ENABLED |
| #include "stm32wlxx_hal_flash.h" |
| #endif /* HAL_FLASH_MODULE_ENABLED */ |
| |
| #ifdef HAL_GPIO_MODULE_ENABLED |
| #include "stm32wlxx_hal_gpio.h" |
| #endif /* HAL_GPIO_MODULE_ENABLED */ |
| |
| #ifdef HAL_GTZC_MODULE_ENABLED |
| #include "stm32wlxx_hal_gtzc.h" |
| #endif /* HAL_GTZC_MODULE_ENABLED */ |
| |
| #ifdef HAL_HSEM_MODULE_ENABLED |
| #include "stm32wlxx_hal_hsem.h" |
| #endif /* HAL_HSEM_MODULE_ENABLED */ |
| |
| #ifdef HAL_I2C_MODULE_ENABLED |
| #include "stm32wlxx_hal_i2c.h" |
| #endif /* HAL_I2C_MODULE_ENABLED */ |
| |
| #ifdef HAL_I2S_MODULE_ENABLED |
| #include "stm32wlxx_hal_i2s.h" |
| #endif /* HAL_I2S_MODULE_ENABLED */ |
| |
| #ifdef HAL_IPCC_MODULE_ENABLED |
| #include "stm32wlxx_hal_ipcc.h" |
| #endif /* HAL_IPCC_MODULE_ENABLED */ |
| |
| #ifdef HAL_IRDA_MODULE_ENABLED |
| #include "stm32wlxx_hal_irda.h" |
| #endif /* HAL_IRDA_MODULE_ENABLED */ |
| |
| #ifdef HAL_IWDG_MODULE_ENABLED |
| #include "stm32wlxx_hal_iwdg.h" |
| #endif /* HAL_IWDG_MODULE_ENABLED */ |
| |
| #ifdef HAL_LPTIM_MODULE_ENABLED |
| #include "stm32wlxx_hal_lptim.h" |
| #endif /* HAL_LPTIM_MODULE_ENABLED */ |
| |
| #ifdef HAL_PKA_MODULE_ENABLED |
| #include "stm32wlxx_hal_pka.h" |
| #endif /* HAL_PKA_MODULE_ENABLED */ |
| |
| #ifdef HAL_PWR_MODULE_ENABLED |
| #include "stm32wlxx_hal_pwr.h" |
| #endif /* HAL_PWR_MODULE_ENABLED */ |
| |
| #ifdef HAL_RCC_MODULE_ENABLED |
| #include "stm32wlxx_hal_rcc.h" |
| #endif /* HAL_RCC_MODULE_ENABLED */ |
| |
| #ifdef HAL_RNG_MODULE_ENABLED |
| #include "stm32wlxx_hal_rng.h" |
| #endif /* HAL_RNG_MODULE_ENABLED */ |
| |
| #ifdef HAL_RTC_MODULE_ENABLED |
| #include "stm32wlxx_hal_rtc.h" |
| #endif /* HAL_RTC_MODULE_ENABLED */ |
| |
| #ifdef HAL_SMARTCARD_MODULE_ENABLED |
| #include "stm32wlxx_hal_smartcard.h" |
| #endif /* HAL_SMARTCARD_MODULE_ENABLED */ |
| |
| #ifdef HAL_SMBUS_MODULE_ENABLED |
| #include "stm32wlxx_hal_smbus.h" |
| #endif /* HAL_SMBUS_MODULE_ENABLED */ |
| |
| #ifdef HAL_SPI_MODULE_ENABLED |
| #include "stm32wlxx_hal_spi.h" |
| #endif /* HAL_SPI_MODULE_ENABLED */ |
| |
| #ifdef HAL_SUBGHZ_MODULE_ENABLED |
| #include "stm32wlxx_hal_subghz.h" |
| #endif /* HAL_SUBGHZ_MODULE_ENABLED */ |
| |
| #ifdef HAL_TIM_MODULE_ENABLED |
| #include "stm32wlxx_hal_tim.h" |
| #endif /* HAL_TIM_MODULE_ENABLED */ |
| |
| #ifdef HAL_UART_MODULE_ENABLED |
| #include "stm32wlxx_hal_uart.h" |
| #endif /* HAL_UART_MODULE_ENABLED */ |
| |
| #ifdef HAL_USART_MODULE_ENABLED |
| #include "stm32wlxx_hal_usart.h" |
| #endif /* HAL_USART_MODULE_ENABLED */ |
| |
| #ifdef HAL_WWDG_MODULE_ENABLED |
| #include "stm32wlxx_hal_wwdg.h" |
| #endif /* HAL_WWDG_MODULE_ENABLED */ |
| |
| /* Exported macro ------------------------------------------------------------*/ |
| #ifdef USE_FULL_ASSERT |
| /** |
| * @brief The assert_param macro is used for function's parameters check. |
| * @param expr If expr is false, it calls assert_failed function |
| * which reports the name of the source file and the source |
| * line number of the call that failed. |
| * If expr is true, it returns no value. |
| * @retval None |
| */ |
| #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) |
| /* Exported functions ------------------------------------------------------- */ |
| void assert_failed(uint8_t* file, uint32_t line); |
| #else |
| #define assert_param(expr) ((void)0U) |
| #endif /* USE_FULL_ASSERT */ |
| |
| #ifdef __cplusplus |
| } |
| #endif |
| |
| #endif /* STM32WLxx_HAL_CONF_H */ |
| |
| /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |