| /** |
| ****************************************************************************** |
| * @file stm32wlxx_hal_rtc_ex.h |
| * @author MCD Application Team |
| * @brief Header file of RTC HAL Extended module. |
| ****************************************************************************** |
| * @attention |
| * |
| * <h2><center>© Copyright (c) 2020 STMicroelectronics. |
| * All rights reserved.</center></h2> |
| * |
| * This software component is licensed by ST under BSD 3-Clause license, |
| * the "License"; You may not use this file except in compliance with the |
| * License. You may obtain a copy of the License at: |
| * opensource.org/licenses/BSD-3-Clause |
| * |
| ****************************************************************************** |
| */ |
| |
| /* Define to prevent recursive inclusion -------------------------------------*/ |
| #ifndef STM32WLxx_HAL_RTC_EX_H |
| #define STM32WLxx_HAL_RTC_EX_H |
| |
| #ifdef __cplusplus |
| extern "C" { |
| #endif |
| |
| /* Includes ------------------------------------------------------------------*/ |
| #include "stm32wlxx_hal_def.h" |
| |
| /** @addtogroup STM32WLxx_HAL_Driver |
| * @{ |
| */ |
| |
| /** @defgroup RTCEx RTCEx |
| * @{ |
| */ |
| |
| /* Exported types ------------------------------------------------------------*/ |
| /** @defgroup RTCEx_Exported_Types RTCEx Exported Types |
| * @{ |
| */ |
| |
| /** @defgroup RTCEx_Tamper_structure_definition RTCEx Tamper structure definition |
| * @{ |
| */ |
| typedef struct |
| { |
| uint32_t Tamper; /*!< Specifies the Tamper Pin. |
| This parameter can be a value of @ref RTCEx_Tamper_Pins */ |
| |
| uint32_t Trigger; /*!< Specifies the Tamper Trigger. |
| This parameter can be a value of @ref RTCEx_Tamper_Trigger */ |
| |
| uint32_t NoErase; /*!< Specifies the Tamper no erase mode. |
| This parameter can be a value of @ref RTCEx_Tamper_EraseBackUp */ |
| |
| uint32_t MaskFlag; /*!< Specifies the Tamper Flag masking. |
| This parameter can be a value of @ref RTCEx_Tamper_MaskFlag */ |
| |
| uint32_t Filter; /*!< Specifies the TAMP Filter Tamper. |
| This parameter can be a value of @ref RTCEx_Tamper_Filter */ |
| |
| uint32_t SamplingFrequency; /*!< Specifies the sampling frequency. |
| This parameter can be a value of @ref RTCEx_Tamper_Sampling_Frequencies */ |
| |
| uint32_t PrechargeDuration; /*!< Specifies the Precharge Duration . |
| This parameter can be a value of @ref RTCEx_Tamper_Pin_Precharge_Duration */ |
| |
| uint32_t TamperPullUp; /*!< Specifies the Tamper PullUp . |
| This parameter can be a value of @ref RTCEx_Tamper_Pull_UP */ |
| |
| uint32_t TimeStampOnTamperDetection; /*!< Specifies the TimeStampOnTamperDetection. |
| This parameter can be a value of @ref RTCEx_Tamper_TimeStampOnTamperDetection */ |
| } RTC_TamperTypeDef; |
| /** |
| * @} |
| */ |
| |
| /** @defgroup RTCEx_Internal_Tamper_structure_definition RTCEx Internal Tamper structure definition |
| * @{ |
| */ |
| typedef struct |
| { |
| uint32_t IntTamper; /*!< Specifies the Internal Tamper Pin. |
| This parameter can be a value of @ref RTCEx_Internal_Tamper_Pins */ |
| |
| uint32_t TimeStampOnTamperDetection; /*!< Specifies the TimeStampOnTamperDetection. |
| This parameter can be a value of @ref RTCEx_Tamper_TimeStampOnTamperDetection */ |
| |
| uint32_t NoErase; /*!< Specifies the internal Tamper no erase mode. |
| This parameter can be a value of @ref RTCEx_Tamper_EraseBackUp */ |
| } RTC_InternalTamperTypeDef; |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Exported constants --------------------------------------------------------*/ |
| /** @defgroup RTCEx_Exported_Constants RTCEx Exported Constants |
| * @{ |
| */ |
| |
| /** @defgroup RTCEx_Time_Stamp_Edges_definitions RTCEx Time Stamp Edges definition |
| * @{ |
| */ |
| #define RTC_TIMESTAMPEDGE_RISING 0x00000000u |
| #define RTC_TIMESTAMPEDGE_FALLING RTC_CR_TSEDGE |
| /** |
| * @} |
| */ |
| |
| /** @defgroup RTCEx_TimeStamp_Pin_Selections RTCEx TimeStamp Pin Selection |
| * @{ |
| */ |
| #define RTC_TIMESTAMPPIN_DEFAULT 0x00000000u |
| /** |
| * @} |
| */ |
| |
| /** @defgroup RTCEx_Wakeup_Timer_Definitions RTCEx Wakeup Timer Definitions |
| * @{ |
| */ |
| #define RTC_WAKEUPCLOCK_RTCCLK_DIV16 0x00000000u |
| #define RTC_WAKEUPCLOCK_RTCCLK_DIV8 RTC_CR_WUCKSEL_0 |
| #define RTC_WAKEUPCLOCK_RTCCLK_DIV4 RTC_CR_WUCKSEL_1 |
| #define RTC_WAKEUPCLOCK_RTCCLK_DIV2 (RTC_CR_WUCKSEL_0 | RTC_CR_WUCKSEL_1) |
| #define RTC_WAKEUPCLOCK_CK_SPRE_16BITS RTC_CR_WUCKSEL_2 |
| #define RTC_WAKEUPCLOCK_CK_SPRE_17BITS (RTC_CR_WUCKSEL_1 | RTC_CR_WUCKSEL_2) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup RTCEx_Smooth_calib_period_Definitions RTCEx Smooth calib period Definitions |
| * @{ |
| */ |
| #define RTC_SMOOTHCALIB_PERIOD_32SEC 0x00000000u /*!< If RTCCLK = 32768 Hz, Smooth calibration |
| period is 32s, else 2exp20 RTCCLK pulses */ |
| #define RTC_SMOOTHCALIB_PERIOD_16SEC RTC_CALR_CALW16 /*!< If RTCCLK = 32768 Hz, Smooth calibration |
| period is 16s, else 2exp19 RTCCLK pulses */ |
| #define RTC_SMOOTHCALIB_PERIOD_8SEC RTC_CALR_CALW8 /*!< If RTCCLK = 32768 Hz, Smooth calibration |
| period is 8s, else 2exp18 RTCCLK pulses */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup RTCEx_Smooth_calib_Plus_pulses_Definitions RTCEx Smooth calib Plus pulses Definitions |
| * @{ |
| */ |
| #define RTC_SMOOTHCALIB_PLUSPULSES_SET RTC_CALR_CALP /*!< The number of RTCCLK pulses added |
| during a X -second window = Y - CALM[8:0] |
| with Y = 512, 256, 128 when X = 32, 16, 8 */ |
| #define RTC_SMOOTHCALIB_PLUSPULSES_RESET 0x00000000u /*!< The number of RTCCLK pulses subbstited |
| during a 32-second window = CALM[8:0] */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup RTCEx_Smooth_calib_low_power_Definitions RTCEx Smooth calib Low Power Definitions |
| * @{ |
| */ |
| #define RTC_LPCAL_SET RTC_CALR_LPCAL /*!< Calibration window is 220 ck_apre, |
| which is the required configuration for |
| ultra-low consumption mode. */ |
| #define RTC_LPCAL_RESET 0x00000000u /*!< Calibration window is 220 RTCCLK, |
| which is a high-consumption mode. |
| This mode should be set only when less |
| than 32s calibration window is required. */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup RTCEx_Calib_Output_selection_Definitions RTCEx Calib Output selection Definitions |
| * @{ |
| */ |
| #define RTC_CALIBOUTPUT_512HZ 0x00000000u |
| #define RTC_CALIBOUTPUT_1HZ RTC_CR_COSEL |
| |
| /** |
| * @} |
| */ |
| |
| |
| /** @defgroup RTCEx_Add_1_Second_Parameter_Definition RTCEx Add 1 Second Parameter Definitions |
| * @{ |
| */ |
| #define RTC_SHIFTADD1S_RESET 0x00000000u |
| #define RTC_SHIFTADD1S_SET RTC_SHIFTR_ADD1S |
| /** |
| * @} |
| */ |
| |
| /** @defgroup RTCEx_Tamper_Pins RTCEx Tamper Pins Definition |
| * @{ |
| */ |
| #define RTC_TAMPER_1 TAMP_CR1_TAMP1E |
| #define RTC_TAMPER_2 TAMP_CR1_TAMP2E |
| #define RTC_TAMPER_3 TAMP_CR1_TAMP3E |
| #define RTC_TAMPER_ALL (TAMP_CR1_TAMP1E | TAMP_CR1_TAMP2E | TAMP_CR1_TAMP3E) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup RTCEx_Internal_Tamper_Pins RTCEx Internal Tamper Pins Definition |
| * @{ |
| */ |
| #define RTC_INT_TAMPER_3 TAMP_CR1_ITAMP3E |
| #define RTC_INT_TAMPER_5 TAMP_CR1_ITAMP5E |
| #define RTC_INT_TAMPER_6 TAMP_CR1_ITAMP6E |
| #define RTC_INT_TAMPER_8 TAMP_CR1_ITAMP8E |
| #define RTC_INT_TAMPER_ALL (TAMP_CR1_ITAMP3E | TAMP_CR1_ITAMP5E | TAMP_CR1_ITAMP6E | TAMP_CR1_ITAMP8E) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup RTCEx_Tamper_Trigger RTCEx Tamper Trigger |
| * @{ |
| */ |
| #define RTC_TAMPERTRIGGER_RISINGEDGE 0x00u /*!< Warning : Filter must be RTC_TAMPERFILTER_DISABLE */ |
| #define RTC_TAMPERTRIGGER_FALLINGEDGE 0x01u /*!< Warning : Filter must be RTC_TAMPERFILTER_DISABLE */ |
| #define RTC_TAMPERTRIGGER_LOWLEVEL 0x02u /*!< Warning : Filter must not be RTC_TAMPERFILTER_DISABLE */ |
| #define RTC_TAMPERTRIGGER_HIGHLEVEL 0x03u /*!< Warning : Filter must not be RTC_TAMPERFILTER_DISABLE */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup RTCEx_Tamper_MaskFlag RTCEx Tamper MaskFlag |
| * @{ |
| */ |
| #define RTC_TAMPERMASK_FLAG_DISABLE 0x00u |
| #define RTC_TAMPERMASK_FLAG_ENABLE 0x01u |
| /** |
| * @} |
| */ |
| |
| /** @defgroup RTCEx_Tamper_EraseBackUp RTCEx Tamper EraseBackUp |
| * @{ |
| */ |
| #define RTC_TAMPER_ERASE_BACKUP_ENABLE 0x00u |
| #define RTC_TAMPER_ERASE_BACKUP_DISABLE 0x01u |
| /** |
| * @} |
| */ |
| |
| /** @defgroup RTCEx_Tamper_Filter RTCEx Tamper Filter |
| * @{ |
| */ |
| #define RTC_TAMPERFILTER_DISABLE 0x00000000U /*!< Tamper filter is disabled */ |
| #define RTC_TAMPERFILTER_2SAMPLE TAMP_FLTCR_TAMPFLT_0 /*!< Tamper is activated after 2 |
| consecutive samples at the active level */ |
| #define RTC_TAMPERFILTER_4SAMPLE TAMP_FLTCR_TAMPFLT_1 /*!< Tamper is activated after 4 |
| consecutive samples at the active level */ |
| #define RTC_TAMPERFILTER_8SAMPLE TAMP_FLTCR_TAMPFLT /*!< Tamper is activated after 8 |
| consecutive samples at the active level */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup RTCEx_Tamper_Sampling_Frequencies RTCEx Tamper Sampling Frequencies |
| * @{ |
| */ |
| #define RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV32768 0x00000000U /*!< Each of the tamper inputs are sampled |
| with a frequency = RTCCLK / 32768 */ |
| #define RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV16384 TAMP_FLTCR_TAMPFREQ_0 /*!< Each of the tamper inputs are sampled |
| with a frequency = RTCCLK / 16384 */ |
| #define RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV8192 TAMP_FLTCR_TAMPFREQ_1 /*!< Each of the tamper inputs are sampled |
| with a frequency = RTCCLK / 8192 */ |
| #define RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV4096 (TAMP_FLTCR_TAMPFREQ_0 | TAMP_FLTCR_TAMPFREQ_1) /*!< Each of the tamper inputs are sampled |
| with a frequency = RTCCLK / 4096 */ |
| #define RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV2048 TAMP_FLTCR_TAMPFREQ_2 /*!< Each of the tamper inputs are sampled |
| with a frequency = RTCCLK / 2048 */ |
| #define RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV1024 (TAMP_FLTCR_TAMPFREQ_0 | TAMP_FLTCR_TAMPFREQ_2) /*!< Each of the tamper inputs are sampled |
| with a frequency = RTCCLK / 1024 */ |
| #define RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV512 (TAMP_FLTCR_TAMPFREQ_1 | TAMP_FLTCR_TAMPFREQ_2) /*!< Each of the tamper inputs are sampled |
| with a frequency = RTCCLK / 512 */ |
| #define RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV256 (TAMP_FLTCR_TAMPFREQ_0 | TAMP_FLTCR_TAMPFREQ_1 | \ |
| TAMP_FLTCR_TAMPFREQ_2) /*!< Each of the tamper inputs are sampled |
| with a frequency = RTCCLK / 256 */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup RTCEx_Tamper_Pin_Precharge_Duration RTCEx Tamper Pin Precharge Duration |
| * @{ |
| */ |
| #define RTC_TAMPERPRECHARGEDURATION_1RTCCLK 0x00000000U /*!< Tamper pins are pre-charged before |
| sampling during 1 RTCCLK cycle */ |
| #define RTC_TAMPERPRECHARGEDURATION_2RTCCLK TAMP_FLTCR_TAMPPRCH_0 /*!< Tamper pins are pre-charged before |
| sampling during 2 RTCCLK cycles */ |
| #define RTC_TAMPERPRECHARGEDURATION_4RTCCLK TAMP_FLTCR_TAMPPRCH_1 /*!< Tamper pins are pre-charged before |
| sampling during 4 RTCCLK cycles */ |
| #define RTC_TAMPERPRECHARGEDURATION_8RTCCLK (TAMP_FLTCR_TAMPPRCH_0 | TAMP_FLTCR_TAMPPRCH_1) /*!< Tamper pins are pre-charged before |
| sampling during 8 RTCCLK cycles */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup RTCEx_Tamper_Pull_UP RTCEx Tamper Pull UP |
| * @{ |
| */ |
| #define RTC_TAMPER_PULLUP_ENABLE 0x00000000u /*!< Tamper pins are pre-charged before sampling */ |
| #define RTC_TAMPER_PULLUP_DISABLE TAMP_FLTCR_TAMPPUDIS /*!< Tamper pins pre-charge is disabled */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup RTCEx_Tamper_TimeStampOnTamperDetection RTCEx Tamper TimeStamp On Tamper Detection Definitions |
| * @{ |
| */ |
| #define RTC_TIMESTAMPONTAMPERDETECTION_DISABLE 0x00000000u /*!< TimeStamp on Tamper Detection event is not saved */ |
| #define RTC_TIMESTAMPONTAMPERDETECTION_ENABLE RTC_CR_TAMPTS /*!< TimeStamp on Tamper Detection event saved */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup RTCEx_Internal_Tamper_Interrupt RTCEx Internal Tamper Interrupt |
| * @{ |
| */ |
| #define RTC_IT_TAMP_1 TAMP_IER_TAMP1IE /*!< Tamper 1 Interrupt */ |
| #define RTC_IT_TAMP_2 TAMP_IER_TAMP2IE /*!< Tamper 2 Interrupt */ |
| #define RTC_IT_TAMP_3 TAMP_IER_TAMP3IE /*!< Tamper 3 Interrupt */ |
| #define RTC_IT_TAMP_ALL (TAMP_IER_TAMP1IE | TAMP_IER_TAMP2IE | TAMP_IER_TAMP3IE) |
| |
| #define RTC_IT_INT_TAMP_3 TAMP_IER_ITAMP3IE |
| #define RTC_IT_INT_TAMP_5 TAMP_IER_ITAMP5IE |
| #define RTC_IT_INT_TAMP_6 TAMP_IER_ITAMP6IE |
| #define RTC_IT_INT_TAMP_8 TAMP_IER_ITAMP8IE |
| #define RTC_IT_INT_TAMP_ALL (TAMP_IT_INT_TAMP3 | TAMP_IT_INT_TAMP5 | TAMP_IT_INT_TAMP6 | TAMP_IT_INT_TAMP8) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup RTCEx_Flags RTCEx Flags |
| * @{ |
| */ |
| #define RTC_FLAG_TAMP_1 TAMP_SR_TAMP1F |
| #define RTC_FLAG_TAMP_2 TAMP_SR_TAMP2F |
| #define RTC_FLAG_TAMP_3 TAMP_SR_TAMP3F |
| #define RTC_FLAG_TAMP_ALL (RTC_FLAG_TAMP1 | RTC_FLAG_TAMP2 | RTC_FLAG_TAMP3 ) |
| |
| |
| #define RTC_FLAG_INT_TAMP_3 TAMP_SR_ITAMP3F |
| #define RTC_FLAG_INT_TAMP_5 TAMP_SR_ITAMP5F |
| #define RTC_FLAG_INT_TAMP_6 TAMP_SR_ITAMP6F |
| #define RTC_FLAG_INT_TAMP_8 TAMP_SR_ITAMP8F |
| #define RTC_FLAG_INT_TAMP_ALL (RTC_FLAG_INT_TAMP3 | RTC_FLAG_INT_TAMP5 | RTC_FLAG_INT_TAMP6 | RTC_FLAG_INT_TAMP8) |
| /** |
| * @} |
| */ |
| |
| |
| /** @defgroup RTCEx_MonotonicCounter_Instance RTCEx Monotonic Counter Instance Definition |
| * @{ |
| */ |
| #define RTC_MONOTONIC_COUNTER_1 0u /*!< Monotonic counter 1 */ |
| /** |
| * @} |
| */ |
| |
| |
| /** @defgroup RTCEx_Backup_Registers RTCEx Backup Registers Definition |
| * @{ |
| */ |
| #define RTC_BKP_NUMBER RTC_BACKUP_NB |
| #define RTC_BKP_DR0 0x00u |
| #define RTC_BKP_DR1 0x01u |
| #define RTC_BKP_DR2 0x02u |
| #define RTC_BKP_DR3 0x03u |
| #define RTC_BKP_DR4 0x04u |
| #define RTC_BKP_DR5 0x05u |
| #define RTC_BKP_DR6 0x06u |
| #define RTC_BKP_DR7 0x07u |
| #define RTC_BKP_DR8 0x08u |
| #define RTC_BKP_DR9 0x09u |
| #define RTC_BKP_DR10 0x0Au |
| #define RTC_BKP_DR11 0x0Bu |
| #define RTC_BKP_DR12 0x0Cu |
| #define RTC_BKP_DR13 0x0Du |
| #define RTC_BKP_DR14 0x0Eu |
| #define RTC_BKP_DR15 0x0Fu |
| #define RTC_BKP_DR16 0x10u |
| #define RTC_BKP_DR17 0x11u |
| #define RTC_BKP_DR18 0x12u |
| #define RTC_BKP_DR19 0x13u |
| /** |
| * @} |
| */ |
| |
| /** @defgroup RTCEx_Binary_Mode RTC Binary Mode (32-bit free-running counter configuration). |
| * Warning : It Should not be confused with the Binary format @ref RTC_Input_parameter_format_definitions. |
| * @{ |
| */ |
| #define RTC_BINARY_NONE 0x00000000u /*!< Free running BCD calendar mode (Binary mode disabled). */ |
| #define RTC_BINARY_ONLY RTC_ICSR_BIN_0 /*!< Free running Binary mode (BCD mode disabled) */ |
| #define RTC_BINARY_MIX RTC_ICSR_BIN_1 /*!< Free running BCD calendar and Binary mode */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup RTCEx_Binary_mix_BCDU If Binary mode is RTC_BINARY_MIX, the BCD calendar second is incremented using the SSR Least Significant Bits. |
| * @{ |
| */ |
| #define RTC_BINARY_MIX_BCDU_0 0x00000000u /*!< The 1s BCD calendar increment is generated each time SS[7:0] = 0 */ |
| #define RTC_BINARY_MIX_BCDU_1 (0x1UL << RTC_ICSR_BCDU_Pos) /*!< The 1s BCD calendar increment is generated each time SS[8:0] = 0 */ |
| #define RTC_BINARY_MIX_BCDU_2 (0x2UL << RTC_ICSR_BCDU_Pos) /*!< The 1s BCD calendar increment is generated each time SS[9:0] = 0 */ |
| #define RTC_BINARY_MIX_BCDU_3 (0x3UL << RTC_ICSR_BCDU_Pos) /*!< The 1s BCD calendar increment is generated each time SS[10:0] = 0 */ |
| #define RTC_BINARY_MIX_BCDU_4 (0x4UL << RTC_ICSR_BCDU_Pos) /*!< The 1s BCD calendar increment is generated each time SS[11:0] = 0 */ |
| #define RTC_BINARY_MIX_BCDU_5 (0x5UL << RTC_ICSR_BCDU_Pos) /*!< The 1s BCD calendar increment is generated each time SS[12:0] = 0 */ |
| #define RTC_BINARY_MIX_BCDU_6 (0x6UL << RTC_ICSR_BCDU_Pos) /*!< The 1s BCD calendar increment is generated each time SS[13:0] = 0 */ |
| #define RTC_BINARY_MIX_BCDU_7 (0x7UL << RTC_ICSR_BCDU_Pos) /*!< The 1s BCD calendar increment is generated each time SS[14:0] = 0 */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup RTCEx_Alarm_Sub_Seconds_binary_Masks_Definitions RTC Alarm Sub Seconds with binary mode Masks Definitions |
| * @{ |
| */ |
| #define RTC_ALARMSUBSECONDBINMASK_ALL 0x00000000u /*!< All Alarm SS fields are masked. |
| There is no comparison on sub seconds for Alarm */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31_1 (1UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:1] are don't care in Alarm |
| comparison. Only SS[0] is compared. */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31_2 (2UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:2] are don't care in Alarm |
| comparison. Only SS[1:0] are compared */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31_3 (3UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:3] are don't care in Alarm |
| comparison. Only SS[2:0] are compared */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31_4 (4UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:4] are don't care in Alarm |
| comparison. Only SS[3:0] are compared */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31_5 (5UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:5] are don't care in Alarm |
| comparison. Only SS[4:0] are compared */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31_6 (6UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:6] are don't care in Alarm |
| comparison. Only SS[5:0] are compared */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31_7 (7UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:7] are don't care in Alarm |
| comparison. Only SS[6:0] are compared */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31_8 (8UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:8] are don't care in Alarm |
| comparison. Only SS[7:0] are compared */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31_9 (9UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:9] are don't care in Alarm |
| comparison. Only SS[8:0] are compared */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31_10 (10UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:10] are don't care in Alarm |
| comparison. Only SS[9:0] are compared */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31_11 (11UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:11] are don't care in Alarm |
| comparison. Only SS[10:0] are compared */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31_12 (12UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:12] are don't care in Alarm |
| comparison.Only SS[11:0] are compared */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31_13 (13UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:13] are don't care in Alarm |
| comparison. Only SS[12:0] are compared */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31_14 (14UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:14] are don't care in Alarm |
| comparison. Only SS[13:0] are compared */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31_15 (15UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:15] are don't care in Alarm |
| comparison. Only SS[14:0] are compared */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31_16 (16UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:16] are don't care in Alarm |
| comparison. Only SS[15:0] are compared */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31_17 (17UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:17] are don't care in Alarm |
| comparison. Only SS[16:0] are compared */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31_18 (18UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:18] are don't care in Alarm |
| comparison. Only SS[17:0] are compared */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31_19 (19UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:19] are don't care in Alarm |
| comparison. Only SS[18:0] are compared */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31_20 (20UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:20] are don't care in Alarm |
| comparison. Only SS[19:0] are compared */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31_21 (21UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:21] are don't care in Alarm |
| comparison. Only SS[20:0] are compared */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31_22 (22UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:22] are don't care in Alarm |
| comparison. Only SS[21:0] are compared */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31_23 (23UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:23] are don't care in Alarm |
| comparison. Only SS[22:0] are compared */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31_24 (24UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:24] are don't care in Alarm |
| comparison. Only SS[23:0] are compared */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31_25 (25UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:25] are don't care in Alarm |
| comparison. Only SS[24:0] are compared */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31_26 (26UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:26] are don't care in Alarm |
| comparison. Only SS[25:0] are compared */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31_27 (27UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:27] are don't care in Alarm |
| comparison. Only SS[26:0] are compared */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31_28 (28UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:28] are don't care in Alarm |
| comparison. Only SS[27:0] are compared */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31_29 (29UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:29] are don't care in Alarm |
| comparison. Only SS[28:0] are compared */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31_30 (30UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:30] are don't care in Alarm |
| comparison. Only SS[29:0] are compared */ |
| #define RTC_ALARMSUBSECONDBINMASK_SS31 (31UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31] is don't care in Alarm |
| comparison. Only SS[30:0] are compared */ |
| #define RTC_ALARMSUBSECONDBINMASK_NONE (32UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:0] are compared and must match to activate alarm. */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup RTCEx_Alarm_Sub_Seconds_binary_Clear_Definitions RTC Alarm Sub Seconds with binary mode auto clear Definitions |
| * @{ |
| */ |
| #define RTC_ALARMSUBSECONDBIN_AUTOCLR_NO 0UL /*!< The synchronous Binary counter (SS[31:0] in RTC_SSR) is free-running. */ |
| #define RTC_ALARMSUBSECONDBIN_AUTOCLR_YES RTC_ALRMASSR_SSCLR /*!< The synchronous Binary counter (SS[31:0] in RTC_SSR) is running from 0xFFFF FFFF to |
| RTC_ALRMABINR -> SS[31:0] value and is automatically reloaded with 0xFFFF FFFF |
| whenreaching RTC_ALRMABINR -> SS[31:0]. */ |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Exported macros -----------------------------------------------------------*/ |
| /** @defgroup RTCEx_Exported_Macros RTCEx Exported Macros |
| * @{ |
| */ |
| |
| /** @brief Clear the specified RTC pending flag. |
| * @param __HANDLE__ specifies the RTC Handle. |
| * @param __FLAG__ specifies the flag to check. |
| * This parameter can be any combination of the following values: |
| * @arg @ref RTC_CLEAR_ITSF Clear Internal Time-stamp flag |
| * @arg @ref RTC_CLEAR_TSOVF Clear Time-stamp overflow flag |
| * @arg @ref RTC_CLEAR_TSF Clear Time-stamp flag |
| * @arg @ref RTC_CLEAR_WUTF Clear Wakeup timer flag |
| * @arg @ref RTC_CLEAR_ALRBF Clear Alarm B flag |
| * @arg @ref RTC_CLEAR_ALRAF Clear Alarm A flag |
| * @retval None |
| */ |
| #define __HAL_RTC_CLEAR_FLAG(__HANDLE__, __FLAG__) (RTC->SCR = (__FLAG__)) |
| |
| /** @brief Check whether the specified RTC flag is set or not. |
| * @param __HANDLE__ specifies the RTC Handle. |
| * @param __FLAG__ specifies the flag to check. |
| * This parameter can be any combination of the following values: |
| * @arg @ref RTC_FLAG_RECALPF Recalibration pending Flag |
| * @arg @ref RTC_FLAG_INITF Initialization flag |
| * @arg @ref RTC_FLAG_RSF Registers synchronization flag |
| * @arg @ref RTC_FLAG_INITS Initialization status flag |
| * @arg @ref RTC_FLAG_SHPF Shift operation pending flag |
| * @arg @ref RTC_FLAG_WUTWF Wakeup timer write flag |
| * @arg @ref RTC_FLAG_ITSF Internal Time-stamp flag |
| * @arg @ref RTC_FLAG_TSOVF Time-stamp overflow flag |
| * @arg @ref RTC_FLAG_TSF Time-stamp flag |
| * @arg @ref RTC_FLAG_WUTF Wakeup timer flag |
| * @arg @ref RTC_FLAG_ALRBF Alarm B flag |
| * @arg @ref RTC_FLAG_ALRAF Alarm A flag |
| * @retval None |
| */ |
| #define __HAL_RTC_GET_FLAG(__HANDLE__, __FLAG__) (((((__FLAG__)) >> 8U) == 1U) ? (RTC->ICSR & (1U << (((uint16_t)(__FLAG__)) & RTC_FLAG_MASK))) : \ |
| (RTC->SR & (1U << (((uint16_t)(__FLAG__)) & RTC_FLAG_MASK)))) |
| |
| /* ---------------------------------WAKEUPTIMER---------------------------------*/ |
| /** @defgroup RTCEx_WakeUp_Timer RTC WakeUp Timer |
| * @{ |
| */ |
| /** |
| * @brief Enable the RTC WakeUp Timer peripheral. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @retval None |
| */ |
| #define __HAL_RTC_WAKEUPTIMER_ENABLE(__HANDLE__) (RTC->CR |= (RTC_CR_WUTE)) |
| |
| /** |
| * @brief Disable the RTC WakeUp Timer peripheral. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @retval None |
| */ |
| #define __HAL_RTC_WAKEUPTIMER_DISABLE(__HANDLE__) (RTC->CR &= ~(RTC_CR_WUTE)) |
| |
| /** |
| * @brief Enable the RTC WakeUpTimer interrupt. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @param __INTERRUPT__ specifies the RTC WakeUpTimer interrupt sources to be enabled. |
| * This parameter can be: |
| * @arg @ref RTC_IT_WUT WakeUpTimer interrupt |
| * @retval None |
| */ |
| #define __HAL_RTC_WAKEUPTIMER_ENABLE_IT(__HANDLE__, __INTERRUPT__) (RTC->CR |= (__INTERRUPT__)) |
| |
| /** |
| * @brief Disable the RTC WakeUpTimer interrupt. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @param __INTERRUPT__ specifies the RTC WakeUpTimer interrupt sources to be disabled. |
| * This parameter can be: |
| * @arg @ref RTC_IT_WUT WakeUpTimer interrupt |
| * @retval None |
| */ |
| #define __HAL_RTC_WAKEUPTIMER_DISABLE_IT(__HANDLE__, __INTERRUPT__) (RTC->CR &= ~(__INTERRUPT__)) |
| |
| |
| /** |
| * @brief Check whether the specified RTC WakeUpTimer interrupt has occurred or not. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @param __INTERRUPT__ specifies the RTC WakeUpTimer interrupt to check. |
| * This parameter can be: |
| * @arg @ref RTC_IT_WUT WakeUpTimer interrupt |
| * @retval None |
| */ |
| #define __HAL_RTC_WAKEUPTIMER_GET_IT(__HANDLE__, __INTERRUPT__) ((((RTC->MISR) & ((__INTERRUPT__)>> 12U)) != 0UL) ? 1UL : 0UL) |
| /** |
| * @brief Check whether the specified RTC Wake Up timer interrupt has been enabled or not. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @param __INTERRUPT__ specifies the RTC Wake Up timer interrupt sources to check. |
| * This parameter can be: |
| * @arg @ref RTC_IT_WUT WakeUpTimer interrupt |
| * @retval None |
| */ |
| #define __HAL_RTC_WAKEUPTIMER_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) ((((RTC->CR) & (__INTERRUPT__)) != 0UL) ? 1UL : 0UL) |
| |
| /** |
| * @brief Get the selected RTC WakeUpTimers flag status. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @param __FLAG__ specifies the RTC WakeUpTimer Flag is pending or not. |
| * This parameter can be: |
| * @arg @ref RTC_FLAG_WUTF |
| * @arg @ref RTC_FLAG_WUTWF |
| * @retval None |
| */ |
| #define __HAL_RTC_WAKEUPTIMER_GET_FLAG(__HANDLE__, __FLAG__) (__HAL_RTC_GET_FLAG((__HANDLE__), (__FLAG__))) |
| |
| /** |
| * @brief Clear the RTC Wake Up timers pending flags. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @param __FLAG__ specifies the RTC WakeUpTimer Flag to clear. |
| * This parameter can be: |
| * @arg @ref RTC_FLAG_WUTF |
| * @retval None |
| */ |
| #define __HAL_RTC_WAKEUPTIMER_CLEAR_FLAG(__HANDLE__, __FLAG__) (__HAL_RTC_CLEAR_FLAG((__HANDLE__), RTC_CLEAR_WUTF)) |
| |
| /* WAKE-UP TIMER EXTI */ |
| /* ------------------ */ |
| #if defined(CORE_CM0PLUS) |
| #define __HAL_RTC_WAKEUPTIMER_EXTI_ENABLE_IT() (EXTI->C2IMR1 |= RTC_EXTI_LINE_WAKEUPTIMER_EVENT) |
| #define __HAL_RTC_WAKEUPTIMER_EXTI_DISABLE_IT() (EXTI->C2IMR1 &= ~(RTC_EXTI_LINE_WAKEUPTIMER_EVENT)) |
| #define __HAL_RTC_WAKEUPTIMER_EXTI_ENABLE_EVENT() (EXTI->C2EMR1 |= RTC_EXTI_LINE_WAKEUPTIMER_EVENT) |
| #define __HAL_RTC_WAKEUPTIMER_EXTI_DISABLE_EVENT() (EXTI->C2EMR1 &= ~(RTC_EXTI_LINE_WAKEUPTIMER_EVENT)) |
| #else |
| #define __HAL_RTC_WAKEUPTIMER_EXTI_ENABLE_IT() (EXTI->IMR1 |= RTC_EXTI_LINE_WAKEUPTIMER_EVENT) |
| #define __HAL_RTC_WAKEUPTIMER_EXTI_DISABLE_IT() (EXTI->IMR1 &= ~(RTC_EXTI_LINE_WAKEUPTIMER_EVENT)) |
| #define __HAL_RTC_WAKEUPTIMER_EXTI_ENABLE_EVENT() (EXTI->EMR1 |= RTC_EXTI_LINE_WAKEUPTIMER_EVENT) |
| #define __HAL_RTC_WAKEUPTIMER_EXTI_DISABLE_EVENT() (EXTI->EMR1 &= ~(RTC_EXTI_LINE_WAKEUPTIMER_EVENT)) |
| #endif |
| |
| /** |
| * @} |
| */ |
| |
| |
| |
| |
| |
| /* ---------------------------------TIMESTAMP---------------------------------*/ |
| /** @defgroup RTCEx_Timestamp RTC Timestamp |
| * @{ |
| */ |
| /** |
| * @brief Enable the RTC TimeStamp peripheral. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @retval None |
| */ |
| #define __HAL_RTC_TIMESTAMP_ENABLE(__HANDLE__) (RTC->CR |= (RTC_CR_TSE)) |
| |
| /** |
| * @brief Disable the RTC TimeStamp peripheral. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @retval None |
| */ |
| #define __HAL_RTC_TIMESTAMP_DISABLE(__HANDLE__) (RTC->CR &= ~(RTC_CR_TSE)) |
| |
| /** |
| * @brief Enable the RTC TimeStamp interrupt. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @param __INTERRUPT__ specifies the RTC TimeStamp interrupt source to be enabled. |
| * This parameter can be: |
| * @arg @ref RTC_IT_TS TimeStamp interrupt |
| * @retval None |
| */ |
| #define __HAL_RTC_TIMESTAMP_ENABLE_IT(__HANDLE__, __INTERRUPT__) (RTC->CR |= (__INTERRUPT__)) |
| |
| /** |
| * @brief Disable the RTC TimeStamp interrupt. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @param __INTERRUPT__ specifies the RTC TimeStamp interrupt source to be disabled. |
| * This parameter can be: |
| * @arg @ref RTC_IT_TS TimeStamp interrupt |
| * @retval None |
| */ |
| #define __HAL_RTC_TIMESTAMP_DISABLE_IT(__HANDLE__, __INTERRUPT__) (RTC->CR &= ~(__INTERRUPT__)) |
| |
| /** |
| * @brief Check whether the specified RTC TimeStamp interrupt has occurred or not. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @param __INTERRUPT__ specifies the RTC TimeStamp interrupt to check. |
| * This parameter can be: |
| * @arg @ref RTC_IT_TS TimeStamp interrupt |
| * @retval None |
| */ |
| #define __HAL_RTC_TIMESTAMP_GET_IT(__HANDLE__, __INTERRUPT__) ((((RTC->MISR) & ((__INTERRUPT__)>> 12U)) != 0U) ? 1UL : 0UL) |
| /** |
| * @brief Check whether the specified RTC Time Stamp interrupt has been enabled or not. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @param __INTERRUPT__ specifies the RTC Time Stamp interrupt source to check. |
| * This parameter can be: |
| * @arg @ref RTC_IT_TS TimeStamp interrupt |
| * @retval None |
| */ |
| #define __HAL_RTC_TIMESTAMP_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) ((((RTC->CR) & (__INTERRUPT__)) != 0U) ? 1UL : 0UL) |
| |
| /** |
| * @brief Get the selected RTC TimeStamps flag status. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @param __FLAG__ specifies the RTC TimeStamp Flag is pending or not. |
| * This parameter can be: |
| * @arg @ref RTC_FLAG_TSF |
| * @arg @ref RTC_FLAG_TSOVF |
| * @retval None |
| */ |
| #define __HAL_RTC_TIMESTAMP_GET_FLAG(__HANDLE__, __FLAG__) (__HAL_RTC_GET_FLAG((__HANDLE__),(__FLAG__))) |
| |
| /** |
| * @brief Clear the RTC Time Stamps pending flags. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @param __FLAG__ specifies the RTC TimeStamp Flag to clear. |
| * This parameter can be: |
| * @arg @ref RTC_FLAG_TSF |
| * @arg @ref RTC_FLAG_TSOVF |
| * @retval None |
| */ |
| #define __HAL_RTC_TIMESTAMP_CLEAR_FLAG(__HANDLE__, __FLAG__) (__HAL_RTC_CLEAR_FLAG((__HANDLE__), (__FLAG__))) |
| |
| /* TIMESTAMP EXTI */ |
| /* -------------- */ |
| #if defined(CORE_CM0PLUS) |
| #define __HAL_RTC_TIMESTAMP_EXTI_ENABLE_IT() (EXTI->C2IMR1 |= RTC_EXTI_LINE_TIMESTAMP_EVENT) |
| #define __HAL_RTC_TIMESTAMP_EXTI_DISABLE_IT() (EXTI->C2IMR1 &= ~(RTC_EXTI_LINE_TIMESTAMP_EVENT)) |
| #define __HAL_RTC_TIMESTAMP_EXTI_ENABLE_EVENT() (EXTI->C2EMR1 |= RTC_EXTI_LINE_TIMESTAMP_EVENT) |
| #define __HAL_RTC_TIMESTAMP_EXTI_DISABLE_EVENT() (EXTI->C2EMR1 &= ~(RTC_EXTI_LINE_TIMESTAMP_EVENT)) |
| #else |
| #define __HAL_RTC_TIMESTAMP_EXTI_ENABLE_IT() (EXTI->IMR1 |= RTC_EXTI_LINE_TIMESTAMP_EVENT) |
| #define __HAL_RTC_TIMESTAMP_EXTI_DISABLE_IT() (EXTI->IMR1 &= ~(RTC_EXTI_LINE_TIMESTAMP_EVENT)) |
| #define __HAL_RTC_TIMESTAMP_EXTI_ENABLE_EVENT() (EXTI->EMR1 |= RTC_EXTI_LINE_TIMESTAMP_EVENT) |
| #define __HAL_RTC_TIMESTAMP_EXTI_DISABLE_EVENT() (EXTI->EMR1 &= ~(RTC_EXTI_LINE_TIMESTAMP_EVENT)) |
| #endif |
| |
| /** |
| * @brief Enable the RTC internal TimeStamp peripheral. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @retval None |
| */ |
| #define __HAL_RTC_INTERNAL_TIMESTAMP_ENABLE(__HANDLE__) (RTC->CR |= (RTC_CR_ITSE)) |
| |
| /** |
| * @brief Disable the RTC internal TimeStamp peripheral. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @retval None |
| */ |
| #define __HAL_RTC_INTERNAL_TIMESTAMP_DISABLE(__HANDLE__) (RTC->CR &= ~(RTC_CR_ITSE)) |
| |
| /** |
| * @brief Get the selected RTC Internal Time Stamps flag status. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @param __FLAG__ specifies the RTC Internal Time Stamp Flag is pending or not. |
| * This parameter can be: |
| * @arg @ref RTC_FLAG_ITSF |
| * @retval None |
| */ |
| #define __HAL_RTC_INTERNAL_TIMESTAMP_GET_FLAG(__HANDLE__, __FLAG__) (__HAL_RTC_GET_FLAG((__HANDLE__),(__FLAG__))) |
| |
| /** |
| * @brief Clear the RTC Internal Time Stamps pending flags. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @param __FLAG__ specifies the RTC Internal Time Stamp Flag source to clear. |
| * This parameter can be: |
| * @arg @ref RTC_FLAG_ITSF |
| * @retval None |
| */ |
| #define __HAL_RTC_INTERNAL_TIMESTAMP_CLEAR_FLAG(__HANDLE__, __FLAG__) (__HAL_RTC_CLEAR_FLAG((__HANDLE__), RTC_CLEAR_ITSF)) |
| |
| /** |
| * @brief Enable the RTC TimeStamp on Tamper detection. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @retval None |
| */ |
| #define __HAL_RTC_TAMPTS_ENABLE(__HANDLE__) (RTC->CR |= (RTC_CR_TAMPTS)) |
| |
| /** |
| * @brief Disable the RTC TimeStamp on Tamper detection. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @retval None |
| */ |
| #define __HAL_RTC_TAMPTS_DISABLE(__HANDLE__) (RTC->CR &= ~(RTC_CR_TAMPTS)) |
| |
| /** |
| * @brief Enable the RTC Tamper detection output. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @retval None |
| */ |
| #define __HAL_RTC_TAMPOE_ENABLE(__HANDLE__) (RTC->CR |= (RTC_CR_TAMPOE)) |
| |
| /** |
| * @brief Disable the RTC Tamper detection output. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @retval None |
| */ |
| #define __HAL_RTC_TAMPOE_DISABLE(__HANDLE__) (RTC->CR &= ~(RTC_CR_TAMPOE)) |
| |
| |
| /** |
| * @} |
| */ |
| |
| |
| /* ------------------------------Calibration----------------------------------*/ |
| /** @defgroup RTCEx_Calibration RTC Calibration |
| * @{ |
| */ |
| |
| /** |
| * @brief Enable the RTC calibration output. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @retval None |
| */ |
| #define __HAL_RTC_CALIBRATION_OUTPUT_ENABLE(__HANDLE__) (RTC->CR |= (RTC_CR_COE)) |
| |
| /** |
| * @brief Disable the calibration output. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @retval None |
| */ |
| #define __HAL_RTC_CALIBRATION_OUTPUT_DISABLE(__HANDLE__) (RTC->CR &= ~(RTC_CR_COE)) |
| |
| |
| /** |
| * @brief Enable the clock reference detection. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @retval None |
| */ |
| #define __HAL_RTC_CLOCKREF_DETECTION_ENABLE(__HANDLE__) (RTC->CR |= (RTC_CR_REFCKON)) |
| |
| /** |
| * @brief Disable the clock reference detection. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @retval None |
| */ |
| #define __HAL_RTC_CLOCKREF_DETECTION_DISABLE(__HANDLE__) (RTC->CR &= ~(RTC_CR_REFCKON)) |
| |
| |
| /** |
| * @brief Get the selected RTC shift operations flag status. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @param __FLAG__ specifies the RTC shift operation Flag is pending or not. |
| * This parameter can be: |
| * @arg @ref RTC_FLAG_SHPF |
| * @retval None |
| */ |
| #define __HAL_RTC_SHIFT_GET_FLAG(__HANDLE__, __FLAG__) (__HAL_RTC_GET_FLAG((__HANDLE__), (__FLAG__))) |
| /** |
| * @} |
| */ |
| |
| |
| /* ------------------------------Tamper----------------------------------*/ |
| /** @defgroup RTCEx_Tamper RTCEx tamper |
| * @{ |
| */ |
| /** |
| * @brief Enable the TAMP Tamper input detection. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @param __TAMPER__ specifies the RTC Tamper source to be enabled. |
| * This parameter can be any combination of the following values: |
| * @arg RTC_TAMPER_ALL: All tampers |
| * @arg RTC_TAMPER_1: Tamper1 |
| * @arg RTC_TAMPER_2: Tamper2 |
| * @arg RTC_TAMPER_3: Tamper3 |
| * @retval None |
| */ |
| #define __HAL_RTC_TAMPER_ENABLE(__HANDLE__, __TAMPER__) ((TAMP->CR1 |= (__TAMPER__)) |
| |
| /** |
| * @brief Disable the TAMP Tamper input detection. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @param __TAMPER__ specifies the RTC Tamper sources to be enabled. |
| * This parameter can be any combination of the following values: |
| * @arg RTC_TAMPER_ALL: All tampers |
| * @arg RTC_TAMPER_1: Tamper1 |
| * @arg RTC_TAMPER_2: Tamper2 |
| * @arg RTC_TAMPER_3: Tamper3 |
| */ |
| #define __HAL_RTC_TAMPER_DISABLE(__HANDLE__, __TAMPER__) ((TAMP->CR1 &= ~(__TAMPER__)) |
| |
| |
| /**************************************************************************************************/ |
| /** |
| * @brief Enable the TAMP Tamper interrupt. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @param __INTERRUPT__ specifies the RTC Tamper interrupt sources to be enabled. |
| * This parameter can be any combination of the following values: |
| * @arg RTC_IT_TAMP_ALL: All tampers interrupts |
| * @arg RTC_IT_TAMP_1: Tamper1 interrupt |
| * @arg RTC_IT_TAMP_2: Tamper2 interrupt |
| * @arg RTC_IT_TAMP_3: Tamper3 interrupt |
| * @retval None |
| */ |
| #define __HAL_RTC_TAMPER_ENABLE_IT(__HANDLE__, __INTERRUPT__) ((TAMP->IER |= (__INTERRUPT__)) |
| |
| /** |
| * @brief Disable the TAMP Tamper interrupt. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @param __INTERRUPT__ specifies the RTC Tamper interrupt sources to be disabled. |
| * This parameter can be any combination of the following values: |
| * @arg RTC_IT_TAMP_ALL: All tampers interrupts |
| * @arg RTC_IT_TAMP_1: Tamper1 interrupt |
| * @arg RTC_IT_TAMP_2: Tamper2 interrupt |
| * @arg RTC_IT_TAMP_3: Tamper3 interrupt |
| |
| * @retval None |
| */ |
| #define __HAL_RTC_TAMPER_DISABLE_IT(__HANDLE__, __INTERRUPT__) ((TAMP->IER &= ~(__INTERRUPT__)) |
| |
| |
| /**************************************************************************************************/ |
| /** |
| * @brief Check whether the specified RTC Tamper interrupt has occurred or not. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @param __INTERRUPT__ specifies the RTC Tamper interrupt to check. |
| * This parameter can be: |
| * @arg RTC_IT_TAMP_ALL: All tampers interrupts |
| * @arg RTC_IT_TAMP_1: Tamper1 interrupt |
| * @arg RTC_IT_TAMP_2: Tamper2 interrupt |
| * @arg RTC_IT_TAMP_3: Tamper3 interrupt |
| * @arg RTC_IT_INT_TAMP_ALL: All Internal Tamper interrupts |
| * @arg RTC_IT_INT_TAMP_3: Internal Tamper3 interrupt |
| * @arg RTC_IT_INT_TAMP_5: Internal Tamper5 interrupt |
| * @arg RTC_IT_INT_TAMP_6: Internal Tamper6 interrupt |
| * @arg RTC_IT_INT_TAMP_8: Internal Tamper8 interrupt |
| * @retval None |
| */ |
| #define __HAL_RTC_TAMPER_GET_IT(__HANDLE__, __INTERRUPT__) (((((TAMP->MISR) & (__INTERRUPT__)) != 0U) ? 1UL : 0UL) |
| |
| |
| /** |
| * @brief Check whether the specified RTC Tamper interrupt has been enabled or not. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @param __INTERRUPT__ specifies the RTC Tamper interrupt source to check. |
| * This parameter can be: |
| * @arg RTC_IT_TAMP_ALL: All tampers interrupts |
| * @arg RTC_IT_TAMP_1: Tamper1 interrupt |
| * @arg RTC_IT_TAMP_2: Tamper2 interrupt |
| * @arg RTC_IT_TAMP_3: Tamper3 interrupt |
| * @arg RTC_IT_INT_TAMP_ALL: All internal tampers interrupts |
| * @arg RTC_IT_INT_TAMP_3: Internal Tamper3 interrupt |
| * @arg RTC_IT_INT_TAMP_5: Internal Tamper5 interrupt |
| * @arg RTC_IT_INT_TAMP_6: Internal Tamper6 interrupt |
| * @arg RTC_IT_INT_TAMP_8: Internal Tamper8 interrupt |
| * @retval None |
| */ |
| #define __HAL_RTC_TAMPER_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) (((((TAMP->IER) & (__INTERRUPT__)) != 0U) ? 1UL : 0UL) |
| |
| |
| /** |
| * @brief Get the selected RTC Tampers flag status. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @param __FLAG__ specifies the RTC Tamper Flag is pending or not. |
| * This parameter can be: |
| * @arg RTC_FLAG_TAMP_1: Tamper1 flag |
| * @arg RTC_FLAG_TAMP_2: Tamper2 flag |
| * @arg RTC_FLAG_TAMP_3: Tamper3 flag |
| * @arg RTC_FLAG_INT_TAMP_3: Internal Tamper3 interrupt |
| * @arg RTC_FLAG_INT_TAMP_5: Internal Tamper5 interrupt |
| * @arg RTC_FLAG_INT_TAMP_6: Internal Tamper6 interrupt |
| * @arg RTC_FLAG_INT_TAMP_8: Internal Tamper8 interrupt |
| * @retval None |
| */ |
| #define __HAL_RTC_TAMPER_GET_FLAG(__HANDLE__, __FLAG__) ((((TAMP->SR) & (__FLAG__)) != 0U) ? 1UL : 0UL) |
| |
| /** |
| * @brief Clear the RTC Tamper's pending flags. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @param __FLAG__ specifies the RTC Tamper Flag to clear. |
| * This parameter can be: |
| * @arg RTC_FLAG_TAMP_ALL: All tampers flag |
| * @arg RTC_FLAG_TAMP_1: Tamper1 flag |
| * @arg RTC_FLAG_TAMP_2: Tamper2 flag |
| * @arg RTC_FLAG_TAMP_3: Tamper3 flag |
| * @arg RTC_FLAG_INT_TAMP_ALL: All Internal Tamper flags |
| * @arg RTC_FLAG_INT_TAMP_3: Internal Tamper3 interrupt |
| * @arg RTC_FLAG_INT_TAMP_5: Internal Tamper5 interrupt |
| * @arg RTC_FLAG_INT_TAMP_6: Internal Tamper6 interrupt |
| * @arg RTC_FLAG_INT_TAMP_8: Internal Tamper8 interrupt |
| * @retval None |
| */ |
| #define __HAL_RTC_TAMPER_CLEAR_FLAG(__HANDLE__, __FLAG__) (((TAMP->SCR) = (__FLAG__))) |
| |
| /* TAMPER EXTI */ |
| /* ----------- */ |
| #if defined(CORE_CM0PLUS) |
| #define __HAL_RTC_TAMPER_EXTI_ENABLE_IT() (EXTI->C2IMR1 |= RTC_EXTI_LINE_TAMPER_EVENT) |
| #define __HAL_RTC_TAMPER_EXTI_DISABLE_IT() (EXTI->C2IMR1 &= ~(RTC_EXTI_LINE_TAMPER_EVENT)) |
| #define __HAL_RTC_TAMPER_EXTI_ENABLE_EVENT() (EXTI->C2EMR1 |= RTC_EXTI_LINE_TAMPER_EVENT) |
| #define __HAL_RTC_TAMPER_EXTI_DISABLE_EVENT() (EXTI->C2EMR1 &= ~(RTC_EXTI_LINE_TAMPER_EVENT)) |
| #else |
| #define __HAL_RTC_TAMPER_EXTI_ENABLE_IT() (EXTI->IMR1 |= RTC_EXTI_LINE_TAMPER_EVENT) |
| #define __HAL_RTC_TAMPER_EXTI_DISABLE_IT() (EXTI->IMR1 &= ~(RTC_EXTI_LINE_TAMPER_EVENT)) |
| #define __HAL_RTC_TAMPER_EXTI_ENABLE_EVENT() (EXTI->EMR1 |= RTC_EXTI_LINE_TAMPER_EVENT) |
| #define __HAL_RTC_TAMPER_EXTI_DISABLE_EVENT() (EXTI->EMR1 &= ~(RTC_EXTI_LINE_TAMPER_EVENT)) |
| #endif |
| |
| /** |
| * @} |
| */ |
| |
| /* --------------------------------- SSR Underflow ---------------------------------*/ |
| /** @defgroup RTCEx_SSR_Underflow RTC SSR Underflow |
| * @{ |
| */ |
| |
| /** |
| * @brief Enable the RTC SSRU interrupt. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @param __INTERRUPT__ specifies the RTC SSRU interrupt sources to be enabled. |
| * This parameter can be: |
| * @arg @ref RTC_IT_SSRU SSRU interrupt |
| * @retval None |
| */ |
| #define __HAL_RTC_SSRU_ENABLE_IT(__HANDLE__, __INTERRUPT__) (RTC->CR |= (__INTERRUPT__)) |
| |
| /** |
| * @brief Disable the RTC SSRU interrupt. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @param __INTERRUPT__ specifies the RTC SSRU interrupt sources to be disabled. |
| * This parameter can be: |
| * @arg @ref RTC_IT_SSRU SSRU interrupt |
| * @retval None |
| */ |
| #define __HAL_RTC_SSRU_DISABLE_IT(__HANDLE__, __INTERRUPT__) (RTC->CR &= ~(__INTERRUPT__)) |
| |
| |
| /** |
| * @brief Check whether the specified RTC SSRU interrupt has occurred or not. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @param __INTERRUPT__ specifies the RTC SSRU interrupt to check. |
| * This parameter can be: |
| * @arg @ref RTC_IT_SSRU SSRU interrupt |
| * @retval None |
| */ |
| #define __HAL_RTC_SSRU_GET_IT(__HANDLE__, __INTERRUPT__) ((((RTC->MISR) & ((__INTERRUPT__) >> 1) != 0U) ? 1U : 0U) |
| /** |
| * @brief Check whether the specified RTC Wake Up timer interrupt has been enabled or not. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @param __INTERRUPT__ specifies the RTC Wake Up timer interrupt sources to check. |
| * This parameter can be: |
| * @arg @ref RTC_IT_SSRU SSRU interrupt |
| * @retval None |
| */ |
| #define __HAL_RTC_SSRU_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) ((((RTC->CR) & (__INTERRUPT__)) != 0U) ? 1U : 0U) |
| |
| /** |
| * @brief Get the selected RTC SSRU's flag status. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @param __FLAG__ specifies the RTC SSRU Flag is pending or not. |
| * This parameter can be: |
| * @arg @ref RTC_FLAG_SSRUF |
| * @retval None |
| */ |
| #define __HAL_RTC_SSRU_GET_FLAG(__HANDLE__, __FLAG__) (__HAL_RTC_GET_FLAG((__HANDLE__), (__FLAG__))) |
| |
| /** |
| * @brief Clear the RTC Wake Up timer's pending flags. |
| * @param __HANDLE__ specifies the RTC handle. |
| * @param __FLAG__ specifies the RTC SSRU Flag to clear. |
| * This parameter can be: |
| * @arg @ref RTC_FLAG_SSRUF |
| * @retval None |
| */ |
| #define __HAL_RTC_SSRU_CLEAR_FLAG(__HANDLE__, __FLAG__) (__HAL_RTC_CLEAR_FLAG((__HANDLE__), RTC_CLEAR_SSRUF)) |
| |
| /* SSR Underflow EXTI */ |
| /* ------------------ */ |
| #if defined(CORE_CM0PLUS) |
| #define __HAL_RTC_SSRU_EXTI_ENABLE_IT() (EXTI->C2IMR1 |= RTC_EXTI_LINE_SSRU_EVENT) |
| #define __HAL_RTC_SSRU_EXTI_DISABLE_IT() (EXTI->C2IMR1 &= ~(RTC_EXTI_LINE_SSRU_EVENT)) |
| #define __HAL_RTC_SSRU_EXTI_ENABLE_EVENT() (EXTI->C2EMR1 |= RTC_EXTI_LINE_SSRU_EVENT) |
| #define __HAL_RTC_SSRU_EXTI_DISABLE_EVENT() (EXTI->C2EMR1 &= ~(RTC_EXTI_LINE_SSRU_EVENT)) |
| #else |
| #define __HAL_RTC_SSRU_EXTI_ENABLE_IT() (EXTI->IMR1 |= RTC_EXTI_LINE_SSRU_EVENT) |
| #define __HAL_RTC_SSRU_EXTI_DISABLE_IT() (EXTI->IMR1 &= ~(RTC_EXTI_LINE_SSRU_EVENT)) |
| #define __HAL_RTC_SSRU_EXTI_ENABLE_EVENT() (EXTI->EMR1 |= RTC_EXTI_LINE_SSRU_EVENT) |
| #define __HAL_RTC_SSRU_EXTI_DISABLE_EVENT() (EXTI->EMR1 &= ~(RTC_EXTI_LINE_SSRU_EVENT)) |
| #endif |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Exported functions --------------------------------------------------------*/ |
| /** @defgroup RTCEx_Exported_Functions RTCEx Exported Functions |
| * @{ |
| */ |
| |
| /* RTC TimeStamp functions *****************************************/ |
| /** @defgroup RTCEx_Exported_Functions_Group1 Extended RTC TimeStamp functions |
| * @{ |
| */ |
| |
| HAL_StatusTypeDef HAL_RTCEx_SetTimeStamp(RTC_HandleTypeDef *hrtc, uint32_t TimeStampEdge, uint32_t RTC_TimeStampPin); |
| HAL_StatusTypeDef HAL_RTCEx_SetTimeStamp_IT(RTC_HandleTypeDef *hrtc, uint32_t TimeStampEdge, uint32_t RTC_TimeStampPin); |
| HAL_StatusTypeDef HAL_RTCEx_DeactivateTimeStamp(RTC_HandleTypeDef *hrtc); |
| HAL_StatusTypeDef HAL_RTCEx_SetInternalTimeStamp(RTC_HandleTypeDef *hrtc); |
| HAL_StatusTypeDef HAL_RTCEx_DeactivateInternalTimeStamp(RTC_HandleTypeDef *hrtc); |
| HAL_StatusTypeDef HAL_RTCEx_GetTimeStamp(RTC_HandleTypeDef *hrtc, RTC_TimeTypeDef *sTimeStamp, RTC_DateTypeDef *sTimeStampDate, uint32_t Format); |
| void HAL_RTCEx_TimeStampIRQHandler(RTC_HandleTypeDef *hrtc); |
| HAL_StatusTypeDef HAL_RTCEx_PollForTimeStampEvent(RTC_HandleTypeDef *hrtc, uint32_t Timeout); |
| void HAL_RTCEx_TimeStampEventCallback(RTC_HandleTypeDef *hrtc); |
| /** |
| * @} |
| */ |
| |
| |
| /* RTC Wake-up functions ******************************************************/ |
| /** @defgroup RTCEx_Exported_Functions_Group2 Extended RTC Wake-up functions |
| * @{ |
| */ |
| |
| HAL_StatusTypeDef HAL_RTCEx_SetWakeUpTimer(RTC_HandleTypeDef *hrtc, uint32_t WakeUpCounter, uint32_t WakeUpClock); |
| HAL_StatusTypeDef HAL_RTCEx_SetWakeUpTimer_IT(RTC_HandleTypeDef *hrtc, uint32_t WakeUpCounter, uint32_t WakeUpClock, uint32_t WakeUpAutoClr); |
| HAL_StatusTypeDef HAL_RTCEx_DeactivateWakeUpTimer(RTC_HandleTypeDef *hrtc); |
| uint32_t HAL_RTCEx_GetWakeUpTimer(RTC_HandleTypeDef *hrtc); |
| void HAL_RTCEx_WakeUpTimerIRQHandler(RTC_HandleTypeDef *hrtc); |
| void HAL_RTCEx_WakeUpTimerEventCallback(RTC_HandleTypeDef *hrtc); |
| HAL_StatusTypeDef HAL_RTCEx_PollForWakeUpTimerEvent(RTC_HandleTypeDef *hrtc, uint32_t Timeout); |
| /** |
| * @} |
| */ |
| |
| /* Extended Control functions ************************************************/ |
| /** @defgroup RTCEx_Exported_Functions_Group3 Extended Peripheral Control functions |
| * @{ |
| */ |
| |
| HAL_StatusTypeDef HAL_RTCEx_SetSmoothCalib(RTC_HandleTypeDef *hrtc, uint32_t SmoothCalibPeriod, uint32_t SmoothCalibPlusPulses, uint32_t SmoothCalibMinusPulsesValue); |
| HAL_StatusTypeDef HAL_RTCEx_SetLowPowerCalib(RTC_HandleTypeDef *hrtc, uint32_t LowPowerCalib); |
| HAL_StatusTypeDef HAL_RTCEx_SetSynchroShift(RTC_HandleTypeDef *hrtc, uint32_t ShiftAdd1S, uint32_t ShiftSubFS); |
| HAL_StatusTypeDef HAL_RTCEx_SetCalibrationOutPut(RTC_HandleTypeDef *hrtc, uint32_t CalibOutput); |
| HAL_StatusTypeDef HAL_RTCEx_DeactivateCalibrationOutPut(RTC_HandleTypeDef *hrtc); |
| HAL_StatusTypeDef HAL_RTCEx_SetRefClock(RTC_HandleTypeDef *hrtc); |
| HAL_StatusTypeDef HAL_RTCEx_DeactivateRefClock(RTC_HandleTypeDef *hrtc); |
| HAL_StatusTypeDef HAL_RTCEx_EnableBypassShadow(RTC_HandleTypeDef *hrtc); |
| HAL_StatusTypeDef HAL_RTCEx_DisableBypassShadow(RTC_HandleTypeDef *hrtc); |
| HAL_StatusTypeDef HAL_RTCEx_MonotonicCounterIncrement(RTC_HandleTypeDef *hrtc, uint32_t Instance); |
| HAL_StatusTypeDef HAL_RTCEx_MonotonicCounterGet(RTC_HandleTypeDef *hrtc, uint32_t Instance, uint32_t *Value); |
| HAL_StatusTypeDef HAL_RTCEx_SetSSRU_IT(RTC_HandleTypeDef *hrtc); |
| HAL_StatusTypeDef HAL_RTCEx_DeactivateSSRU(RTC_HandleTypeDef *hrtc); |
| void HAL_RTCEx_SSRUIRQHandler(RTC_HandleTypeDef *hrtc); |
| void HAL_RTCEx_SSRUEventCallback(RTC_HandleTypeDef *hrtc); |
| /** |
| * @} |
| */ |
| |
| /* Extended RTC features functions *******************************************/ |
| /** @defgroup RTCEx_Exported_Functions_Group4 Extended features functions |
| * @{ |
| */ |
| |
| void HAL_RTCEx_AlarmBEventCallback(RTC_HandleTypeDef *hrtc); |
| HAL_StatusTypeDef HAL_RTCEx_PollForAlarmBEvent(RTC_HandleTypeDef *hrtc, uint32_t Timeout); |
| /** |
| * @} |
| */ |
| |
| /** @defgroup RTCEx_Exported_Functions_Group5 Extended RTC Tamper functions |
| * @{ |
| */ |
| HAL_StatusTypeDef HAL_RTCEx_SetTamper(RTC_HandleTypeDef *hrtc, RTC_TamperTypeDef *sTamper); |
| HAL_StatusTypeDef HAL_RTCEx_SetTamper_IT(RTC_HandleTypeDef *hrtc, RTC_TamperTypeDef *sTamper); |
| HAL_StatusTypeDef HAL_RTCEx_DeactivateTamper(RTC_HandleTypeDef *hrtc, uint32_t Tamper); |
| HAL_StatusTypeDef HAL_RTCEx_PollForTamperEvent(RTC_HandleTypeDef *hrtc, uint32_t Tamper, uint32_t Timeout); |
| HAL_StatusTypeDef HAL_RTCEx_SetInternalTamper(RTC_HandleTypeDef *hrtc, RTC_InternalTamperTypeDef *sIntTamper); |
| HAL_StatusTypeDef HAL_RTCEx_SetInternalTamper_IT(RTC_HandleTypeDef *hrtc, RTC_InternalTamperTypeDef *sIntTamper); |
| HAL_StatusTypeDef HAL_RTCEx_DeactivateInternalTamper(RTC_HandleTypeDef *hrtc, uint32_t IntTamper); |
| HAL_StatusTypeDef HAL_RTCEx_PollForInternalTamperEvent(RTC_HandleTypeDef *hrtc, uint32_t IntTamper, uint32_t Timeout); |
| void HAL_RTCEx_TamperIRQHandler(RTC_HandleTypeDef *hrtc); |
| void HAL_RTCEx_Tamper1EventCallback(RTC_HandleTypeDef *hrtc); |
| void HAL_RTCEx_Tamper2EventCallback(RTC_HandleTypeDef *hrtc); |
| void HAL_RTCEx_Tamper3EventCallback(RTC_HandleTypeDef *hrtc); |
| void HAL_RTCEx_InternalTamper3EventCallback(RTC_HandleTypeDef *hrtc); |
| void HAL_RTCEx_InternalTamper5EventCallback(RTC_HandleTypeDef *hrtc); |
| void HAL_RTCEx_InternalTamper6EventCallback(RTC_HandleTypeDef *hrtc); |
| void HAL_RTCEx_InternalTamper8EventCallback(RTC_HandleTypeDef *hrtc); |
| /** |
| * @} |
| */ |
| |
| /** @defgroup RTCEx_Exported_Functions_Group6 Extended RTC Backup register functions |
| * @{ |
| */ |
| void HAL_RTCEx_BKUPWrite(RTC_HandleTypeDef *hrtc, uint32_t BackupRegister, uint32_t Data); |
| uint32_t HAL_RTCEx_BKUPRead(RTC_HandleTypeDef *hrtc, uint32_t BackupRegister); |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Private types -------------------------------------------------------------*/ |
| /* Private variables ---------------------------------------------------------*/ |
| /* Private constants ---------------------------------------------------------*/ |
| /** @defgroup RTCEx_Private_Constants RTCEx Private Constants |
| * @{ |
| */ |
| /*#define RTC_EXTI_LINE_ALARM_EVENT EXTI_IMR1_IM17 */ /*!< External interrupt line 17 Connected to the RTC Alarm event (defined in rtc.h) */ |
| #define RTC_EXTI_LINE_SSRU_EVENT EXTI_IMR1_IM18 /*!< External interrupt line 18 Connected to the RTC SSR Underflow event */ |
| #define RTC_EXTI_LINE_TIMESTAMP_EVENT EXTI_IMR1_IM19 /*!< External interrupt line 19 Connected to the RTC Time Stamp events */ |
| #define RTC_EXTI_LINE_WAKEUPTIMER_EVENT EXTI_IMR1_IM20 /*!< External interrupt line 20 Connected to the RTC Wakeup event */ |
| #define RTC_EXTI_LINE_TAMPER_EVENT EXTI_IMR1_IM19 /*!< External interrupt line 19 Connected to the RTC tamper events */ |
| /** |
| * @} |
| */ |
| |
| /* Private macros ------------------------------------------------------------*/ |
| /** @defgroup RTCEx_Private_Macros RTCEx Private Macros |
| * @{ |
| */ |
| |
| /** @defgroup RTCEx_IS_RTC_Definitions Private macros to check input parameters |
| * @{ |
| */ |
| #define IS_TIMESTAMP_EDGE(EDGE) (((EDGE) == RTC_TIMESTAMPEDGE_RISING) || \ |
| ((EDGE) == RTC_TIMESTAMPEDGE_FALLING)) |
| |
| |
| #define IS_RTC_TIMESTAMP_PIN(PIN) (((PIN) == RTC_TIMESTAMPPIN_DEFAULT)) |
| |
| |
| |
| #define IS_RTC_TIMESTAMPONTAMPER_DETECTION(DETECTION) (((DETECTION) == RTC_TIMESTAMPONTAMPERDETECTION_ENABLE) || \ |
| ((DETECTION) == RTC_TIMESTAMPONTAMPERDETECTION_DISABLE)) |
| |
| #define IS_RTC_TAMPER_TAMPERDETECTIONOUTPUT(MODE) (((MODE) == RTC_TAMPERDETECTIONOUTPUT_ENABLE) || \ |
| ((MODE) == RTC_TAMPERDETECTIONOUTPUT_DISABLE)) |
| |
| #define IS_RTC_WAKEUP_CLOCK(CLOCK) (((CLOCK) == RTC_WAKEUPCLOCK_RTCCLK_DIV16) || \ |
| ((CLOCK) == RTC_WAKEUPCLOCK_RTCCLK_DIV8) || \ |
| ((CLOCK) == RTC_WAKEUPCLOCK_RTCCLK_DIV4) || \ |
| ((CLOCK) == RTC_WAKEUPCLOCK_RTCCLK_DIV2) || \ |
| ((CLOCK) == RTC_WAKEUPCLOCK_CK_SPRE_16BITS) || \ |
| ((CLOCK) == RTC_WAKEUPCLOCK_CK_SPRE_17BITS)) |
| |
| #define IS_RTC_WAKEUP_COUNTER(COUNTER) ((COUNTER) <= RTC_WUTR_WUT) |
| |
| #define IS_RTC_SMOOTH_CALIB_PERIOD(PERIOD) (((PERIOD) == RTC_SMOOTHCALIB_PERIOD_32SEC) || \ |
| ((PERIOD) == RTC_SMOOTHCALIB_PERIOD_16SEC) || \ |
| ((PERIOD) == RTC_SMOOTHCALIB_PERIOD_8SEC)) |
| |
| #define IS_RTC_SMOOTH_CALIB_PLUS(PLUS) (((PLUS) == RTC_SMOOTHCALIB_PLUSPULSES_SET) || \ |
| ((PLUS) == RTC_SMOOTHCALIB_PLUSPULSES_RESET)) |
| |
| #define IS_RTC_SMOOTH_CALIB_MINUS(VALUE) ((VALUE) <= RTC_CALR_CALM) |
| |
| #define IS_RTC_LOW_POWER_CALIB(LPCAL) (((LPCAL) == RTC_LPCAL_SET) || \ |
| ((LPCAL) == RTC_LPCAL_RESET)) |
| |
| |
| #define IS_RTC_TAMPER(__TAMPER__) ((((__TAMPER__) & RTC_TAMPER_ALL) != 0x00U) && \ |
| (((__TAMPER__) & ~RTC_TAMPER_ALL) == 0x00U)) |
| |
| #define IS_RTC_INTERNAL_TAMPER(__INT_TAMPER__) ((((__INT_TAMPER__) & RTC_INT_TAMPER_ALL) != 0x00U) && \ |
| (((__INT_TAMPER__) & ~RTC_INT_TAMPER_ALL) == 0x00U)) |
| |
| #define IS_RTC_TAMPER_TRIGGER(__TRIGGER__) (((__TRIGGER__) == RTC_TAMPERTRIGGER_RISINGEDGE) || \ |
| ((__TRIGGER__) == RTC_TAMPERTRIGGER_FALLINGEDGE) || \ |
| ((__TRIGGER__) == RTC_TAMPERTRIGGER_LOWLEVEL) || \ |
| ((__TRIGGER__) == RTC_TAMPERTRIGGER_HIGHLEVEL)) |
| |
| #define IS_RTC_TAMPER_ERASE_MODE(__MODE__) (((__MODE__) == RTC_TAMPER_ERASE_BACKUP_ENABLE) || \ |
| ((__MODE__) == RTC_TAMPER_ERASE_BACKUP_DISABLE)) |
| |
| #define IS_RTC_TAMPER_MASKFLAG_STATE(__STATE__) (((__STATE__) == RTC_TAMPERMASK_FLAG_ENABLE) || \ |
| ((__STATE__) == RTC_TAMPERMASK_FLAG_DISABLE)) |
| |
| #define IS_RTC_TAMPER_FILTER(__FILTER__) (((__FILTER__) == RTC_TAMPERFILTER_DISABLE) || \ |
| ((__FILTER__) == RTC_TAMPERFILTER_2SAMPLE) || \ |
| ((__FILTER__) == RTC_TAMPERFILTER_4SAMPLE) || \ |
| ((__FILTER__) == RTC_TAMPERFILTER_8SAMPLE)) |
| |
| #define IS_RTC_TAMPER_SAMPLING_FREQ(__FREQ__) (((__FREQ__) == RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV32768)|| \ |
| ((__FREQ__) == RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV16384)|| \ |
| ((__FREQ__) == RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV8192) || \ |
| ((__FREQ__) == RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV4096) || \ |
| ((__FREQ__) == RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV2048) || \ |
| ((__FREQ__) == RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV1024) || \ |
| ((__FREQ__) == RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV512) || \ |
| ((__FREQ__) == RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV256)) |
| |
| #define IS_RTC_TAMPER_PRECHARGE_DURATION(__DURATION__) (((__DURATION__) == RTC_TAMPERPRECHARGEDURATION_1RTCCLK) || \ |
| ((__DURATION__) == RTC_TAMPERPRECHARGEDURATION_2RTCCLK) || \ |
| ((__DURATION__) == RTC_TAMPERPRECHARGEDURATION_4RTCCLK) || \ |
| ((__DURATION__) == RTC_TAMPERPRECHARGEDURATION_8RTCCLK)) |
| |
| #define IS_RTC_TAMPER_PULLUP_STATE(__STATE__) (((__STATE__) == RTC_TAMPER_PULLUP_ENABLE) || \ |
| ((__STATE__) == RTC_TAMPER_PULLUP_DISABLE)) |
| |
| #define IS_RTC_TAMPER_TIMESTAMPONTAMPER_DETECTION(DETECTION) (((DETECTION) == RTC_TIMESTAMPONTAMPERDETECTION_ENABLE) || \ |
| ((DETECTION) == RTC_TIMESTAMPONTAMPERDETECTION_DISABLE)) |
| |
| #define IS_RTC_BKP(__BKP__) ((__BKP__) < RTC_BKP_NUMBER) |
| |
| #define IS_RTC_SHIFT_ADD1S(SEL) (((SEL) == RTC_SHIFTADD1S_RESET) || \ |
| ((SEL) == RTC_SHIFTADD1S_SET)) |
| |
| #define IS_RTC_SHIFT_SUBFS(FS) ((FS) <= RTC_SHIFTR_SUBFS) |
| |
| #define IS_RTC_CALIB_OUTPUT(OUTPUT) (((OUTPUT) == RTC_CALIBOUTPUT_512HZ) || \ |
| ((OUTPUT) == RTC_CALIBOUTPUT_1HZ)) |
| |
| #define IS_RTC_BINARY_MODE(MODE) (((MODE) == RTC_BINARY_NONE) || \ |
| ((MODE) == RTC_BINARY_ONLY) || \ |
| ((MODE) == RTC_BINARY_MIX )) |
| |
| #define IS_RTC_BINARY_MIX_BCDU(BDCU) (((BDCU) == RTC_BINARY_MIX_BCDU_0) || \ |
| ((BDCU) == RTC_BINARY_MIX_BCDU_1) || \ |
| ((BDCU) == RTC_BINARY_MIX_BCDU_2) || \ |
| ((BDCU) == RTC_BINARY_MIX_BCDU_3) || \ |
| ((BDCU) == RTC_BINARY_MIX_BCDU_4) || \ |
| ((BDCU) == RTC_BINARY_MIX_BCDU_5) || \ |
| ((BDCU) == RTC_BINARY_MIX_BCDU_6) || \ |
| ((BDCU) == RTC_BINARY_MIX_BCDU_7)) |
| |
| #define IS_RTC_ALARM_SUB_SECOND_BINARY_MASK(MASK) (((MASK) == 0u) || \ |
| (((MASK) >= RTC_ALARMSUBSECONDBINMASK_SS31_1) && ((MASK) <= RTC_ALARMSUBSECONDBINMASK_NONE))) |
| |
| #define IS_RTC_ALARMSUBSECONDBIN_AUTOCLR(SEL) (((SEL) == RTC_ALARMSUBSECONDBIN_AUTOCLR_NO) || \ |
| ((SEL) == RTC_ALARMSUBSECONDBIN_AUTOCLR_YES)) |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| #ifdef __cplusplus |
| } |
| #endif |
| |
| #endif /* STM32WLxx_HAL_RTC_EX_H */ |
| |
| /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |
