| /* | |
| * SPDX-FileCopyrightText: Copyright (c) 2018, Ha Thach (tinyusb.org) | |
| * SPDX-License-Identifier: MIT | |
| * | |
| * This file is part of the TinyUSB stack. | |
| */ | |
| #include "tusb_option.h" | |
| #if CFG_TUD_ENABLED && CFG_TUSB_MCU == OPT_MCU_NONE | |
| #include "device/dcd.h" | |
| //--------------------------------------------------------------------+ | |
| // MACRO TYPEDEF CONSTANT ENUM DECLARATION | |
| //--------------------------------------------------------------------+ | |
| /*------------------------------------------------------------------*/ | |
| /* Device API | |
| *------------------------------------------------------------------*/ | |
| // Initialize controller to device mode | |
| bool dcd_init(uint8_t rhport, const tusb_rhport_init_t* rh_init) { | |
| (void) rhport; (void) rh_init; | |
| return true; | |
| } | |
| // Enable device interrupt | |
| void dcd_int_enable (uint8_t rhport) { | |
| (void) rhport; | |
| } | |
| // Disable device interrupt | |
| void dcd_int_disable (uint8_t rhport) { | |
| (void) rhport; | |
| } | |
| // Receive Set Address request, mcu port must also include status IN response | |
| void dcd_set_address (uint8_t rhport, uint8_t dev_addr) { | |
| (void) rhport; | |
| (void) dev_addr; | |
| } | |
| // Wake up host | |
| void dcd_remote_wakeup (uint8_t rhport) { | |
| (void) rhport; | |
| } | |
| // Connect by enabling internal pull-up resistor on D+/D- | |
| void dcd_connect(uint8_t rhport) { | |
| (void) rhport; | |
| } | |
| // Disconnect by disabling internal pull-up resistor on D+/D- | |
| void dcd_disconnect(uint8_t rhport) { | |
| (void) rhport; | |
| } | |
| void dcd_sof_enable(uint8_t rhport, bool en) { | |
| (void) rhport; | |
| (void) en; | |
| } | |
| //--------------------------------------------------------------------+ | |
| // Endpoint API | |
| //--------------------------------------------------------------------+ | |
| // Configure endpoint's registers according to descriptor | |
| bool dcd_edpt_open (uint8_t rhport, tusb_desc_endpoint_t const * ep_desc) { | |
| (void) rhport; | |
| (void) ep_desc; | |
| return false; | |
| } | |
| // Allocate packet buffer used by ISO endpoints | |
| // Some MCU need manual packet buffer allocation, we allocate the largest size to avoid clustering | |
| bool dcd_edpt_iso_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t largest_packet_size) { | |
| (void) rhport; | |
| (void) ep_addr; | |
| (void) largest_packet_size; | |
| return false; | |
| } | |
| // Configure and enable an ISO endpoint according to descriptor | |
| bool dcd_edpt_iso_activate(uint8_t rhport, tusb_desc_endpoint_t const * desc_ep) { | |
| (void) rhport; | |
| (void) desc_ep; | |
| return false; | |
| } | |
| void dcd_edpt_close_all (uint8_t rhport) { | |
| (void) rhport; | |
| } | |
| // Submit a transfer, When complete dcd_event_xfer_complete() is invoked to notify the stack | |
| bool dcd_edpt_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t * buffer, uint16_t total_bytes, bool is_isr) { | |
| (void) is_isr; | |
| (void) rhport; | |
| (void) ep_addr; | |
| (void) buffer; | |
| (void) total_bytes; | |
| return false; | |
| } | |
| // Submit a transfer where is managed by FIFO, When complete dcd_event_xfer_complete() is invoked to notify the stack - optional, however, must be listed in usbd.c | |
| bool dcd_edpt_xfer_fifo(uint8_t rhport, uint8_t ep_addr, tu_fifo_t * ff, uint16_t total_bytes, bool is_isr) { | |
| (void) is_isr; | |
| (void) rhport; | |
| (void) ep_addr; | |
| (void) ff; | |
| (void) total_bytes; | |
| return false; | |
| } | |
| // Stall endpoint | |
| void dcd_edpt_stall (uint8_t rhport, uint8_t ep_addr) { | |
| (void) rhport; | |
| (void) ep_addr; | |
| } | |
| // clear stall, data toggle is also reset to DATA0 | |
| void dcd_edpt_clear_stall (uint8_t rhport, uint8_t ep_addr) { | |
| (void) rhport; | |
| (void) ep_addr; | |
| } | |
| #endif |