docs/troubleshooting.rst

***************
Troubleshooting
***************

This guide helps you diagnose and fix common issues when developing with TinyUSB.

Build Issues
============

Toolchain Problems
------------------

**"arm-none-eabi-gcc: command not found"**

The ARM GCC toolchain is not installed or not in PATH.

*Solution*:

.. code-block:: bash

   # Ubuntu/Debian
   $ sudo apt-get update && sudo apt-get install gcc-arm-none-eabi

   # macOS with Homebrew
   $ brew install --cask gcc-arm-embedded

   # Windows: Download from ARM website and add to PATH

**"make: command not found" or CMake errors**

Build tools are missing.

*Solution*:

.. code-block:: bash

   # Ubuntu/Debian
   $ sudo apt-get install build-essential cmake

   # macOS
   $ xcode-select --install
   $ brew install cmake

Dependency Issues
-----------------

**"No rule to make target" or missing header files**

Dependencies for your MCU family are not downloaded.

*Solution*:

.. code-block:: bash

   # Download dependencies for specific board or family
   $ python tools/get_deps.py -b stm32h743eval  # Replace with your board
   $ python tools/get_deps.py stm32f4           # Replace with your family

   # Or from example directory
   cd examples/device/cdc_msc
   make BOARD=your_board get-deps

**Board Not Found**

Invalid board name in build command.

*Diagnosis*:

.. code-block:: bash

   # List available boards for a family
   ls hw/bsp/stm32f4/boards/

*Solution*: Use exact board name from the listing.

Runtime Issues
==============

Check :doc:`reference/device_issues` for known hardware-specific issues that may affect USB functionality on your device.

Device Mode Problems
--------------------

**Device not recognized by host**

The most common issue - host doesn't see your USB device.

*Diagnosis steps*:

1. Check USB cable (must support data, not just power)
2. Enable logging: build with ``LOG=2``
3. Use different USB ports/hosts
4. Check device manager (Windows) or ``dmesg`` (Linux)

*Common causes and solutions*:

- **Invalid descriptors**: Review ``usb_descriptors.c`` carefully
- **``tud_task()`` not called**: Ensure regular calls in main loop (< 1ms interval)
- **Wrong USB configuration**: Check ``tusb_config.h`` settings
- **Hardware issues**: Verify USB pins, crystal/clock configuration

**Enumeration starts but fails**

Device is detected but configuration fails.

*Diagnosis*:

.. code-block:: bash

   # Build with logging enabled
   make BOARD=your_board LOG=2 all

*Look for*:

- Setup request handling errors
- Endpoint configuration problems
- String descriptor issues

*Solutions*:

- Implement all required descriptors
- Check endpoint sizes match descriptors
- Ensure control endpoint (EP0) handling is correct

**Data transfer issues**

Device enumerates but data doesn't transfer correctly.

*Common causes*:

- Buffer overruns in class callbacks
- Incorrect endpoint usage (IN vs OUT)
- Flow control issues in CDC class

*Solutions*:

- Check buffer sizes in callbacks
- Verify endpoint directions in descriptors
- Implement proper flow control

Host Mode Problems
------------------

**No devices detected**

Host application doesn't see connected devices.

*Hardware checks*:

- Power supply adequate for host mode
- USB-A connector for host (not micro-USB)
- Board supports host mode on selected port

*Software checks*:

- ``tuh_task()`` called regularly
- Host stack enabled in ``tusb_config.h``
- Correct root hub port configuration

**Device enumeration fails**

Devices connect but enumeration fails.

*Diagnosis*:

.. code-block:: bash

   # Enable host logging
   make BOARD=your_board LOG=2 RHPORT_HOST=1 all

*Common issues*:

- Power supply insufficient during enumeration
- Timing issues with slow devices
- USB hub compatibility problems

**Class driver issues**

Device enumerates but class-specific communication fails.

*Troubleshooting*:

- Check device descriptors match expected class
- Verify interface/endpoint assignments
- Some devices need device-specific handling

Performance Issues
==================

Slow Transfer Speeds
--------------------

**Symptoms**: Lower than expected USB transfer rates

*Causes and solutions*: Improve **task scheduling** by calling ``tud_task()``/``tuh_task()`` more frequently to ensure timely USB event processing. Consider increasing **endpoint buffer sizes** for bulk transfers to reduce the frequency of small transfers. Enable **DMA usage** for USB transfers if your hardware supports it to offload CPU processing. Finally, use **High Speed** (480 Mbps) instead of Full Speed (12 Mbps) when possible to achieve better throughput.

High CPU Usage
--------------

**Symptoms**: MCU spending too much time in USB handling

*Solutions*:

- Use efficient logging (RTT/SWO instead of UART)
- Reduce log level in production builds
- Optimize descriptor parsing
- Use DMA for data transfers

Hardware-Specific Issues
========================

STM32 Issues
------------

**Clock configuration problems**:

- USB requires precise 48MHz clock
- HSE crystal must be configured correctly
- PLL settings affect USB timing

**Pin configuration**:

- USB pins need specific alternate function settings
- VBUS sensing configuration
- ID pin for OTG applications

RP2040 Issues
-------------

**PIO-USB for host mode**:

- Requires specific pin assignments
- CPU overclocking may be needed for reliable operation
- Timing-sensitive - avoid long interrupt disable periods

ESP32 Issues
------------

**USB peripheral differences**:

- ESP32-S2/S3/P4 have different USB capabilities
- DMA configuration varies between models

Advanced Debugging
==================

Using USB Analyzers
-------------------

For complex issues, hardware USB analyzers provide detailed protocol traces:

- **Wireshark** with USBPcap (Windows) or usbmon (Linux)
- **Hardware analyzers**: Total Phase Beagle, LeCroy USB analyzers
- **Logic analyzers**: For timing analysis of USB signals

Debugging with GDB
------------------

Debugging with traditional debuggers is limited due to the real time nature of USB.
However, especially for diagnosis of crashes, it can still be useful.

.. code-block:: bash

   # Build with debug info
   make BOARD=your_board DEBUG=1 all

   # Use with debugger
   arm-none-eabi-gdb build/your_app.elf

*Useful breakpoints*:

- ``dcd_int_handler()`` - USB interrupt entry
- ``tud_task()`` - Main device task
- Class-specific callbacks

Custom Logging
--------------

For production debugging, implement custom logging:

.. code-block:: c

   // In tusb_config.h
   #define CFG_TUSB_DEBUG_PRINTF   my_printf

   // Your implementation
   void my_printf(const char* format, ...) {
     // Send to RTT, SWO, or custom interface
   }

Getting Help
============

When reporting issues:

1. **Minimal reproducible example**: Simplify to bare minimum
2. **Build information**: Board, toolchain version, build flags
3. **Logs**: Include output with ``LOG=2`` enabled
4. **Hardware details**: Board revision, USB connections, power supply
5. **Host environment**: OS version, USB port type

**Resources**:

- GitHub Discussions: https://github.com/hathach/tinyusb/discussions
- Issue Tracker: https://github.com/hathach/tinyusb/issues
- Documentation: https://docs.tinyusb.org