blob: 2ee5e8735b2192a8717a726ae9943ba73d458988 [file] [log] [blame]
/*
*
* Copyright (c) 2020 Project CHIP Authors
* Copyright (c) 2019 Google LLC.
* All rights reserved.
*
* Licensed under the Apache License, Version 2.0 (the "License");
* you may not use this file except in compliance with the License.
* You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*/
/**
* @file
* Example project configuration file for CHIP.
*
* This is a place to put application or project-specific overrides
* to the default configuration values for general CHIP features.
*
*/
#pragma once
// Use a default pairing code if one hasn't been provisioned in flash.
#ifndef CHIP_DEVICE_CONFIG_USE_TEST_SETUP_PIN_CODE
#define CHIP_DEVICE_CONFIG_USE_TEST_SETUP_PIN_CODE 20202021
#endif
#ifndef CHIP_DEVICE_CONFIG_USE_TEST_SETUP_DISCRIMINATOR
#define CHIP_DEVICE_CONFIG_USE_TEST_SETUP_DISCRIMINATOR 0xF00
#endif
// For convenience, Chip Security Test Mode can be enabled and the
// requirement for authentication in various protocols can be disabled.
//
// WARNING: These options make it possible to circumvent basic Chip security functionality,
// including message encryption. Because of this they MUST NEVER BE ENABLED IN PRODUCTION BUILDS.
//
#define CHIP_CONFIG_SECURITY_TEST_MODE 0
/**
* CHIP_DEVICE_CONFIG_DEVICE_VENDOR_ID
*
* 0xFFF1: Test vendor.
*/
#define CHIP_DEVICE_CONFIG_DEVICE_VENDOR_ID 0xFFF1
/**
* CHIP_DEVICE_CONFIG_DEVICE_PRODUCT_ID
*
* 0x8009: example window app
*/
#define CHIP_DEVICE_CONFIG_DEVICE_PRODUCT_ID 0x8010
/**
* CHIP_DEVICE_CONFIG_ENABLE_CHIPOBLE
*
* Enable support for Chip-over-BLE (CHIPoBLE).
*/
#define CHIP_DEVICE_CONFIG_ENABLE_CHIPOBLE 1
/**
* CHIP_DEVICE_CONFIG_TEST_SERIAL_NUMBER
*
* Enables the use of a hard-coded default serial number if none
* is found in Chip NV storage.
*/
#define CHIP_DEVICE_CONFIG_TEST_SERIAL_NUMBER "TEST_SN"
/**
* CHIP_DEVICE_CONFIG_EVENT_LOGGING_UTC_TIMESTAMPS
*
* Enable recording UTC timestamps.
*/
#define CHIP_DEVICE_CONFIG_EVENT_LOGGING_UTC_TIMESTAMPS 1
/**
* CHIP_DEVICE_CONFIG_EVENT_LOGGING_DEBUG_BUFFER_SIZE
*
* A size, in bytes, of the individual debug event logging buffer.
*/
#define CHIP_DEVICE_CONFIG_EVENT_LOGGING_DEBUG_BUFFER_SIZE (512)
/**
* CHIP_DEVICE_CONFIG_BLE_FAST_ADVERTISING_INTERVAL
*
* The interval (in units of 0.625ms) at which the device will send BLE advertisements while
* in fast advertising mode.
*
* 40 (25ms).
*/
#define CHIP_DEVICE_CONFIG_BLE_FAST_ADVERTISING_INTERVAL 40
/**
* CHIP_DEVICE_CONFIG_BLE_SLOW_ADVERTISING_INTERVAL
*
* The interval (in units of 0.625ms) at which the device will send BLE advertisements while
* in slow advertisement mode.
*
* 800 (500ms).
*/
#define CHIP_DEVICE_CONFIG_BLE_SLOW_ADVERTISING_INTERVAL 800
/**
* CHIP_DEVICE_CONFIG_BLE_FAST_ADVERTISING_TIMEOUT
*
* The amount of time in miliseconds after which BLE should change his advertisements
* from fast interval to slow interval.
*
* 30000 (30 secondes).
*/
#define CHIP_DEVICE_CONFIG_BLE_FAST_ADVERTISING_TIMEOUT (30 * 1000)
/**
* @def CHIP_CONFIG_MRP_LOCAL_ACTIVE_RETRY_INTERVAL
*
* @brief
* Active retransmit interval, or time to wait before retransmission after
* subsequent failures in milliseconds.
*
* This is the default value, that might be adjusted by end device depending on its
* needs (e.g. sleeping period) using Service Discovery TXT record CRA key.
*
*/
#define CHIP_CONFIG_MRP_LOCAL_ACTIVE_RETRY_INTERVAL (2000_ms32)