config/telink/chip-module/Kconfig.defaults

#
#   Copyright (c) 2023 Project CHIP Authors
#
#   Licensed under the Apache License, Version 2.0 (the "License");
#   you may not use this file except in compliance with the License.
#   You may obtain a copy of the License at
#
#       http://www.apache.org/licenses/LICENSE-2.0
#
#   Unless required by applicable law or agreed to in writing, software
#   distributed under the License is distributed on an "AS IS" BASIS,
#   WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
#   See the License for the specific language governing permissions and
#   limitations under the License.
#

# The purpose of this file is to define new default values of settings used when building Matter samples.
# This file only changes defaults and thus all symbols here must be promptless
# and safeguarded so that they only are applied when building Matter.

if CHIP

config LOG
    default y

if LOG

choice LOG_MODE
    default LOG_MODE_MINIMAL
endchoice

choice MATTER_LOG_LEVEL_CHOICE
    default MATTER_LOG_LEVEL_INF
endchoice

config CHIP_APP_LOG_LEVEL
    default 3 # info

config LOG_DEFAULT_LEVEL
    default 1 # error

config CHIP_LOG_SIZE_OPTIMIZATION
    default y

endif

config SHELL
    default y if CHIP_LIB_SHELL

config PTHREAD_IPC
    bool
    default n

config POSIX_MAX_FDS
    int
    default 16

# Application stack size
config MAIN_STACK_SIZE
    default 3240 if PM
    default 4096

config INIT_STACKS
    default y

config IDLE_STACK_SIZE
    default 512 if PM

config ISR_STACK_SIZE
    default 502 if PM

config SYSTEM_WORKQUEUE_STACK_SIZE
    default 616 if PM

config HEAP_MEM_POOL_SIZE
    default 256

config COMMON_LIBC_MALLOC_ARENA_SIZE 
    default 12288

config NET_IPV6_MLD
    default n

# Network buffers
config NET_PKT_RX_COUNT
    default 4 if PM
    default 8

config NET_PKT_TX_COUNT
    default 4 if PM
    default 8

config NET_BUF_RX_COUNT
    default 16 if PM
    default 32

config NET_BUF_TX_COUNT
    default 16 if PM
    default 32

config GPIO
    default y

# Bluetooth Low Energy configs

config BT
    default y

config BT_PERIPHERAL
    default y

config BT_GATT_DYNAMIC_DB
    default y

config BT_DEVICE_NAME_DYNAMIC
    default y

config BT_DEVICE_NAME_MAX
    default 15

config BT_MAX_CONN
    default 1

config BT_L2CAP_TX_MTU
    default 247

config BT_BUF_ACL_RX_SIZE
    default 251

config BT_BUF_ACL_TX_SIZE
    default 251

config BT_RX_STACK_SIZE
    default 810

config BT_HCI_TX_STACK_SIZE
    default 640

config BT_DEVICE_NAME_GATT_WRITABLE
    bool
    default n

config B9X_BLE_CTRL_THREAD_STACK_SIZE
    default 576

config B9X_BLE_CTRL_MASTER_MAX_NUM
    default 0

config B9X_BLE_CTRL_SLAVE_MAX_NUM
    default 1

config B9X_BLE_CTRL_RF_POWER
    default 3 if PM 
    default 9

choice B9X_BLE_CTRL_MAC_TYPE
    default B9X_BLE_CTRL_MAC_TYPE_RANDOM_STATIC
endchoice

# Board retention config
if BOARD_TLSR9528A_RETENTION || BOARD_TLSR9518ADK80D_RETENTION
config BOARD_TLSR9X_NON_RETENTION_RAM_CODE
    default y if PM

config TELINK_B9x_MATTER_RETENTION_LAYOUT
    default y if PM

config PWM
    default n
endif

# Board non-retention config
if BOARD_TLSR9528A || BOARD_TLSR9518ADK80D
config PWM
    default y
endif

# Config dynamic interrupts to have posibility to switch between BLE/Thread radio drivers
config DYNAMIC_INTERRUPTS
    default y

config CHIP_OTA_REQUESTOR
    default y

# In current config/zephyr/Kconfig
# next deprecated values are selected
# warning: Deprecated symbol CPLUSPLUS is enabled.
# warning: Deprecated symbol LIB_CPLUSPLUS is enabled.
# new one are:
# CONFIG_CPP
# CONFIG_LIBCPP_IMPLEMENTATION
# See https://docs.zephyrproject.org/latest/releases/release-notes-3.3.html
# Since not only Telink is using Zephyr just suppress warnings
config WARN_DEPRECATED
    default n

# Reboot system when fault happened
config TELINK_B9X_REBOOT_ON_FAULT
    default y

config NVS_LOOKUP_CACHE
    default y

config NVS_LOOKUP_CACHE_SIZE
    default 2048 if !PM

# Set multiplicator of Name Value Storage (NVS) as 1 to reach NVS sector size 4KB
# nvs_sector_size = flash_page_size * mult = 4KB * 1 = 4KB
config SETTINGS_NVS_SECTOR_SIZE_MULT
    default 1

# Set sector counter of NVS
config SETTINGS_NVS_SECTOR_COUNT
    default 12

# Enable OpenThread

config NET_L2_OPENTHREAD
    default y

choice CHIP_THREAD_DEVICE_ROLE
    prompt "Thread network device role"
    default CHIP_THREAD_DEVICE_ROLE_ROUTER
config CHIP_THREAD_DEVICE_ROLE_ROUTER
	depends on !PM
	bool "thread device router"
config CHIP_THREAD_DEVICE_ROLE_END_DEVICE
	depends on !PM
	bool "thread end device"
config CHIP_THREAD_DEVICE_ROLE_SLEEPY_END_DEVICE
	bool "thread sleepy end device"
endchoice

choice OPENTHREAD_DEVICE_TYPE
	default OPENTHREAD_FTD if CHIP_THREAD_DEVICE_ROLE_ROUTER
	default OPENTHREAD_MTD if CHIP_THREAD_DEVICE_ROLE_END_DEVICE || CHIP_THREAD_DEVICE_ROLE_SLEEPY_END_DEVICE
endchoice

config CHIP_ENABLE_ICD_SUPPORT
	default y if CHIP_THREAD_DEVICE_ROLE_SLEEPY_END_DEVICE

config OPENTHREAD_THREAD_STACK_SIZE
    default 2178 if PM

config OPENTHREAD_RADIO_WORKQUEUE_STACK_SIZE
    default 361 if PM
    default 608

config OPENTHREAD_SLAAC
    default y

config OPENTHREAD_MANUAL_START
    default y

config OPENTHREAD_DEFAULT_TX_POWER
    default 3 if PM
    default 9

config NET_TX_STACK_SIZE
    default 554 if PM

config NET_RX_STACK_SIZE
    default 554 if PM

# Disable certain parts of Zephyr IPv6 stack
config NET_IPV6_NBR_CACHE
    bool
    default n

config NET_MAX_CONN
    default 1

config NET_MAX_CONTEXTS
    default 1

config NET_CONFIG_INIT_TIMEOUT
    default 0

# mbedTLS tweaks
config MBEDTLS_USER_CONFIG_ENABLE
    default y

config MBEDTLS_USER_CONFIG_FILE
    default "telink-mbedtls-config.h"


# getopt version
config GETOPT_LONG
    default y

# Disable not used shell modules

config SHELL_WILDCARD
    default n

config SHELL_VT100_COLORS
    default n

config SHELL_STATS
    default n

config KERNEL_SHELL
    default n

config SENSOR_SHELL
    default n

config DEVICE_SHELL
    default n

config DATE_SHELL
    default n

config DEVMEM_SHELL
    default n

config MCUBOOT_SHELL
    default n

config FLASH_SHELL
    default n

config HWINFO_SHELL
    default n

config PWM_SHELL
    default n

config OPENTHREAD_SHELL
    default n

config CHIP_TASK_STACK_SIZE
	default 4864 if PM

endif