| # |
| # Copyright (c) 2021 Project CHIP Authors |
| # |
| # Licensed under the Apache License, Version 2.0 (the "License"); |
| # you may not use this file except in compliance with the License. |
| # You may obtain a copy of the License at |
| # |
| # http://www.apache.org/licenses/LICENSE-2.0 |
| # |
| # Unless required by applicable law or agreed to in writing, software |
| # distributed under the License is distributed on an "AS IS" BASIS, |
| # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| # See the License for the specific language governing permissions and |
| # limitations under the License. |
| # |
| |
| CONFIG_CHIP=y |
| CONFIG_STD_CPP14=y |
| |
| # Logging (set CONFIG_SERIAL to 'y' to enable logging and 'n' to disable logging) |
| CONFIG_SERIAL=y |
| CONFIG_LOG=y |
| CONFIG_LOG_MODE_MINIMAL=y |
| CONFIG_PRINTK=y |
| # CONFIG_ASSERT=y |
| CONFIG_CBPRINTF_LIBC_SUBSTS=y |
| |
| # Set the maximum log level (DEBUG) |
| CONFIG_LOG_DEFAULT_LEVEL=4 |
| CONFIG_MATTER_LOG_LEVEL_DBG=y |
| CONFIG_MCUBOOT_BOOTUTIL_LIB=y |
| CONFIG_MCUBOOT_UTIL_LOG_LEVEL_DBG=y |
| CONFIG_NET_LOG=y |
| CONFIG_IEEE802154_DRIVER_LOG_LEVEL_DBG=y |
| CONFIG_NVS_LOG_LEVEL_DBG=y |
| CONFIG_OPENTHREAD_LOG_LEVEL_DEBG=y |
| CONFIG_OPENTHREAD_L2_LOG_LEVEL_DBG=y |
| |
| # Set the actual log level |
| # - 0 OFF, logging is turned off |
| # - 1 ERROR, maximal level set to LOG_LEVEL_ERR |
| # - 2 WARNING, maximal level set to LOG_LEVEL_WRN |
| # - 3 INFO, maximal level set to LOG_LEVEL_INFO |
| # - 4 DEBUG, maximal level set to LOG_LEVEL_DBG |
| CONFIG_LOG_MAX_LEVEL=3 |
| |
| # Generic networking options |
| CONFIG_NETWORKING=y |
| CONFIG_NET_SOCKETS=y |
| CONFIG_NET_SOCKETS_POSIX_NAMES=n |
| CONFIG_NET_CONFIG_INIT_TIMEOUT=0 |
| |
| # Disable TCP and IPv4 (TCP disabled to avoid heavy traffic) |
| CONFIG_NET_TCP=n |
| CONFIG_NET_IPV4=n |
| |
| CONFIG_NET_CONFIG_NEED_IPV4=n |
| CONFIG_NET_CONFIG_MY_IPV4_ADDR="" |
| CONFIG_NET_CONFIG_PEER_IPV4_ADDR="" |
| |
| # Application stack size |
| CONFIG_MAIN_STACK_SIZE=4096 |
| CONFIG_INIT_STACKS=y |
| CONFIG_IDLE_STACK_SIZE=512 |
| |
| # Disable certain parts of Zephyr IPv6 stack |
| CONFIG_NET_IPV6_NBR_CACHE=n |
| CONFIG_NET_IPV6_MLD=n |
| |
| CONFIG_NET_MAX_CONN=1 |
| CONFIG_NET_MAX_CONTEXTS=1 |
| |
| # Network buffers |
| CONFIG_NET_PKT_RX_COUNT=8 |
| CONFIG_NET_PKT_TX_COUNT=8 |
| CONFIG_NET_BUF_RX_COUNT=32 |
| CONFIG_NET_BUF_TX_COUNT=32 |
| |
| # Bluetooth Low Energy configs |
| CONFIG_BT=y |
| CONFIG_BT_DEBUG_LOG=n |
| CONFIG_BT_PERIPHERAL=y |
| CONFIG_BT_MAX_CONN=1 |
| CONFIG_BT_DEVICE_NAME_DYNAMIC=y |
| CONFIG_BT_GATT_DYNAMIC_DB=y |
| # CONFIG_BT_DEVICE_NAME_MAX=15 |
| CONFIG_BT_L2CAP_TX_MTU=247 |
| CONFIG_BT_BUF_ACL_RX_SIZE=251 |
| CONFIG_BT_BUF_ACL_TX_SIZE=251 |
| |
| # L2 OpenThread enabling |
| CONFIG_NET_L2_OPENTHREAD=y |
| CONFIG_OPENTHREAD_DEBUG=y |
| CONFIG_OPENTHREAD_L2_DEBUG=y |
| |
| # OpenThread configs |
| CONFIG_OPENTHREAD_SLAAC=y |
| CONFIG_OPENTHREAD_RADIO_WORKQUEUE_STACK_SIZE=608 |
| CONFIG_OPENTHREAD_MANUAL_START=y |
| |
| # mbedTLS tweaks |
| CONFIG_MBEDTLS_TEST=y |
| CONFIG_MBEDTLS_PKCS5_C=y |
| CONFIG_MBEDTLS_USER_CONFIG_ENABLE=y |
| CONFIG_MBEDTLS_USER_CONFIG_FILE="telink-mbedtls-config.h" |
| |
| # TBD: Something wrong with this heap. Need to be investigated. Cirrently just set minimal size |
| CONFIG_MBEDTLS_HEAP_SIZE=0 |
| CONFIG_OPENTHREAD_EXTERNAL_HEAP=y |
| |
| # Config dynamic interrupts to have posibility to switch between BLE/Thread radio drivers |
| CONFIG_DYNAMIC_INTERRUPTS=y |
| |
| # Set multiplicator of Name Value Storage (NVS) as 8 to reach NVS sector size 2048 |
| # nvs_sector_size = flash_page_size * mult = 256 * 8 = 2048 |
| CONFIG_SETTINGS_NVS_SECTOR_SIZE_MULT=8 |
| |
| # Enable NVS lookup cache |
| CONFIG_NVS_LOOKUP_CACHE=y |
| |
| # Reboot system when fault happened |
| CONFIG_TELINK_B91_REBOOT_ON_FAULT=y |
| |
| # Shell settings |
| CONFIG_SHELL=n |
| |
| # BLE MAC address |
| CONFIG_B91_BLE_CTRL_MAC_FLASH_ADDR=0x1FE000 |
