| # |
| # Copyright (c) 2020 Project CHIP Authors |
| # Copyright (c) 2018 Nest Labs, Inc. |
| # All rights reserved. |
| # |
| # Licensed under the Apache License, Version 2.0 (the "License"); |
| # you may not use this file except in compliance with the License. |
| # You may obtain a copy of the License at |
| # |
| # http://www.apache.org/licenses/LICENSE-2.0 |
| # |
| # Unless required by applicable law or agreed to in writing, software |
| # distributed under the License is distributed on an "AS IS" BASIS, |
| # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| # See the License for the specific language governing permissions and |
| # limitations under the License. |
| # |
| # Description: |
| # Some useful defaults for the demo app configuration. |
| # |
| |
| |
| # Default to 921600 baud when flashing and monitoring device |
| CONFIG_ESPTOOLPY_BAUD_921600B=y |
| CONFIG_ESPTOOLPY_BAUD=921600 |
| CONFIG_ESPTOOLPY_COMPRESSED=y |
| CONFIG_ESPTOOLPY_MONITOR_BAUD_115200B=y |
| CONFIG_ESPTOOLPY_MONITOR_BAUD=115200 |
| |
| #enable BT |
| CONFIG_BT_ENABLED=y |
| CONFIG_BT_NIMBLE_ENABLED=y |
| |
| #disable BT connection reattempt |
| CONFIG_BT_NIMBLE_ENABLE_CONN_REATTEMPT=n |
| |
| #enable lwip ipv6 autoconfig |
| CONFIG_LWIP_IPV6_AUTOCONFIG=y |
| |
| # Use a custom partition table |
| CONFIG_PARTITION_TABLE_CUSTOM=y |
| CONFIG_PARTITION_TABLE_FILENAME="partitions.csv" |
| |
| # Compiler options |
| CONFIG_COMPILER_OPTIMIZATION_SIZE=y |
| CONFIG_COMPILER_OPTIMIZATION_ASSERTIONS_DISABLE=y |
| |
| # Bluetooth controller |
| CONFIG_BTDM_CTRL_BLE_MAX_CONN=1 |
| CONFIG_BTDM_CTRL_BLE_MAX_CONN_EFF=1 |
| |
| # NimBLE Options |
| CONFIG_BT_NIMBLE_MAX_CONNECTIONS=1 |
| |
| # Wi-Fi |
| CONFIG_ESP32_WIFI_STATIC_RX_BUFFER_NUM=4 |
| CONFIG_ESP32_WIFI_DYNAMIC_RX_BUFFER_NUM=8 |
| CONFIG_ESP32_WIFI_DYNAMIC_TX_BUFFER_NUM=16 |
| |
| # FreeRTOS |
| CONFIG_FREERTOS_UNICORE=y |
| |
| # Add RTC memory to system heap |
| CONFIG_ESP_SYSTEM_ALLOW_RTC_FAST_MEM_AS_HEAP=y |
| |
| # LWIP |
| CONFIG_LWIP_TCPIP_RECVMBOX_SIZE=16 |
| |
| # TCP |
| CONFIG_LWIP_TCP_SYNMAXRTX=6 |
| |
| # Compatibility options |
| CONFIG_BTDM_CONTROLLER_BLE_MAX_CONN=1 |
| CONFIG_BTDM_CONTROLLER_BLE_MAX_CONN_EFF=1 |
| CONFIG_NIMBLE_MAX_CONNECTIONS=1 |
| CONFIG_TCPIP_RECVMBOX_SIZE=16 |
| CONFIG_TCP_SYNMAXRTX=6 |
| |
| # Product id |
| CONFIG_DEVICE_VENDOR_ID=0xFFF1 |
| CONFIG_DEVICE_PRODUCT_ID=0x800D |
| |
| # Main task needs a bit more stack than the default |
| # default is 3584, bump this up to 4k. |
| CONFIG_ESP_MAIN_TASK_STACK_SIZE=4096 |
| |
| #enable lwIP route hooks |
| CONFIG_LWIP_HOOK_IP6_ROUTE_DEFAULT=y |
| CONFIG_LWIP_HOOK_ND6_GET_GW_DEFAULT=y |
| |
| # Disable softap support by default |
| CONFIG_ESP_WIFI_SOFTAP_SUPPORT=n |
| |
| # Enable HKDF in mbedtls |
| CONFIG_MBEDTLS_HKDF_C=y |
| |
| # Increase LwIP IPv6 address number |
| CONFIG_LWIP_IPV6_NUM_ADDRESSES=6 |
| |
| # Enable the diagnostic logs transfer over BDX protocol |
| CONFIG_CHIP_ENABLE_BDX_LOG_TRANSFER=y |
| |
| CONFIG_ESP32_ENABLE_COREDUMP_TO_FLASH=y |
| CONFIG_ESP32_COREDUMP_DATA_FORMAT_ELF=y |
