tree: 1488fa9c80d6157ea875ac6eb6958dc3158b9878 [path history] [tgz]
  1. bl602/
  2. bl702/
  3. common/
  4. README.md
examples/lighting-app/bouffalolab/README.md

Bouffalo Lab

This example functions as a light bulb device type, with on/off and level capabilities and uses a test Vendor ID (VID) and a Product ID (PID) of 0x8005.

The steps were verified on Bouffalo Lab BL602 and BL706 development board.

  • BL602-IoT-Matter-V1, here to purchase.
  • BL602-NIGHT-LIGHT
  • XT-ZB6-DevKit
  • BL706-NIGHT-LIGHT

Warning: Changing the PID may cause compilation problems, we recommend leaving it as the default while using this example.

BL602

BL602/BL604 is combo chip-set for Wi-Fi 802.11b/g/n and BLE 5.0 base-band/MAC.

BL602-IoT-Matter-V1

BL706

BL702/BL706 is combo chip-set for BLE and IEEE 802.15.4/ZigBee/Thread. In some cases, e.g. in SDK, we use BL702 as a general name for BL702/BL706 family.

XT-ZB6-DevKit

Initial setup

The following steps in this document were validated on Ubuntu 18.04/20.04 and Mac OS.

  • Install dependencies as specified in the connectedhomeip repository: Building Matter.

  • Clone and initialize the connectedhomeip repo

    git clone https://github.com/project-chip/connectedhomeip.git
    cd connectedhomeip
    git submodule update --init --recursive
    source ./scripts/activate.sh
    

    After environment setup Bouffalolab flash tool, bflb-iot-tool, imports under this environment. If not, please try scripts/bootstrap.sh for matter environment update.

  • Setup build environment for Bouffalo Lab SoC

    Run setup.sh to install Bouffalo Lab SDK to /opt/bouffalolab_sdk

    cd third_party/bouffalolab/repo
    sudo bash scripts/setup.sh
    

    Please execute following command to export BOUFFALOLAB_SDK_ROOT before building.

    export BOUFFALOLAB_SDK_ROOT=/opt/bouffalolab_sdk
    

Build CHIP Lighting App example

The following steps take examples for BL602 develop board BL602-IoT-Matter-V1 and BL706 develop board XT-ZB6-DevKit.

  • Build lighting app with UART baudrate 2000000

    ./scripts/build/build_examples.py --target bouffalolab-bl602-iot-matter-v1-light build
    ./scripts/build/build_examples.py --target bouffalolab-xt-zb6-devkit-light build
    
  • Build lighting app with UART baudrate 115200

    ./scripts/build/build_examples.py --target bouffalolab-bl602-iot-matter-v1-light-115200 build
    ./scripts/build/build_examples.py --target bouffalolab-xt-zb6-devkit-light-115200 build
    
  • Build lighting app with RPC enabled and UART baudrate 115200.

    ./scripts/build/build_examples.py --target bouffalolab-bl602-iot-matter-v1-light-rpc build
    ./scripts/build/build_examples.py --target bouffalolab-xt-zb6-devkit-light-rpc build
    

Download image

  • Using script *.flash.py.

    After building gets done, python script chip-bl602-lighting-example.flash.py or chip-bl702-lighting-example.flash.py will generate under build output folder for BL602 or BL702 building.

    Note 1, *.flash.py should be ran under Matter build environment; if python module bflb_iot_tool is not found, please try to do source scripts/bootstrap.sh or install as pip3 install bflb-iot-tool.
    Note 2, different build options will generate different output folder.

    Download operation steps as below, please check help option of script for more detail.

    • Connect the board to your build machine

    • Put the board to the download mode:

      • Press and hold the BOOT button.
      • Click the RESET or EN button.
      • Release the BOOT button.
    • Type following command for image download. Please set serial port accordingly, here we use /dev/ttyACM0 as a serial port example.

      • bl602-iot-matter-v1 without additional build options

        ./out/bouffalolab-bl602-iot-matter-v1-light/chip-bl602-lighting-example.flash.py --port /dev/ttyACM0
        
      • xt-zb6-devkit with 115200 baudrate setting

        ./out/bouffalolab-xt-zb6-devkit-light-115200/chip-bl702-lighting-example.flash.py --port /dev/ttyACM0
        
      • To wipe out flash and download image, please append --erase to the above command.

        ./out/bouffalolab-bl602-iot-matter-v1-light/chip-bl602-lighting-example.flash.py --port /dev/ttyACM0 --erase
        ./out/bouffalolab-xt-zb6-devkit-light-115200/chip-bl702-lighting-example.flash.py --port /dev/ttyACM0 --erase
        

        Note, better to append --erase option to download image for BL602 develop board at first time.

  • Using Bouffalo Lab GUI flash tool BLDevCube, please download on this page.

    • Hold BOOT pin and reset chip, put the board in download mode.
    • Select DTS file;
    • Select Partition Table under examples/platform/bouffalolab/bl602/flash_config or examples/platform/bouffalolab/bl702/flash_config
    • Select Firmware Bin;
    • Select Chip Erase if need;
    • Choose Target COM port.
    • Then click Create & Download.

Run the example

  • You can open the serial console. For example, if the device is at /dev/ttyACM0 with UART baudrate 2000000 built:

    ```shell
    picocom -b 2000000 /dev/ttyACM0
    ```
    
  • To reset the board, Click the RESET or EN button.

  • To toggle the light bulb’s on/off state by clicking BOOT button, which also toggles the LED.

  • To do factory reset, press BOOT button over 4 seconds, release BOOT button after led blink stopped.

Test Commission and Control with chip-tool

Please follow chip_tool_guide and guide to build and use chip-tool for test.

Prerequisite for Thread Protocol

Thread wireless protocol runs on BL706, which needs a Thread border router to connect Thread network to Wi-Fi/Ethernet network. Please follow this guide to setup a raspberry Pi border router.

After Thread border router setup, please type following command on Thread border router to get Thread network credential.

sudo ot-ctl dataset active -x

Commissioning over BLE

  • Reset the board or factory reset the board

  • Enter build out folder of chip-tool and running the following command to do BLE commission

    • BL602

      ./chip-tool pairing ble-wifi <node_id> <wifi_ssid> <wifi_passwd> 20202021 3840
      
    • BL706

      ./chip-tool pairing ble-thread <node_id> hex:<thread_operational_dataset> 20202021 3840
      

    <node_id>, which is node ID assigned to device within chip-tool fabric
    <wifi_ssid>, Wi-Fi network SSID
    <wifi_passwd>, Wi-FI network password
    <thread_operational_dataset>, Thread network credential which running sudo ot-ctl dataset active -x command on border router to get.

Cluster control

After successful commissioning, cluster commands available to control the board.

  • OnOff cluster

    The following command shows to toggle the LED on the board

    $ ./chip-tool onoff toggle <node_id> 1
    
  • Level cluster

    The following command shows to move level to 128.

    $ ./chip-tool levelcontrol move-to-level 128 10 0 0 <node_id> 1
    
  • Color cluster

    The following command shows to change hue and saturation to 240 and 100

    $ ./chip-tool colorcontrol move-to-hue-and-saturation 240 100 0 0 0 <node_id> 1
    
  • Identify Light

    The following command shows to identify the board 10 seconds

    ./chip-tool identify identify 10 <node_id> 1
    

Test OTA software upgrade with ota-provider-app

Please take guide for more detail on ota-provider-app build and usage.

Create the Matter OTA with Bouffalolab OTA bin FW_OTA.bin.xz.hash

  • Build Bouffalo Lab OTA image as following execution using python script *.flash.py under firmware build out folder,
    ./<output_firmware_name>.flash.py --build
    
    After script executed, a folder ota_images and an image FW_OTA.bin.xz.hash will be generated. FW_OTA.bin.xz.hash is compressed with hash verification for build out firmware.
  • Build Matter *.ota OTA image with Bouffalo Lab OTA image under connectedhomeip repo folder

    $ ./src/app/ota_image_tool.py create -v 0xFFF1 -p 0x8005 -vn 10 -vs "1.0" -da sha256 <FW_OTA.bin.xz.hash> lighting-app.ota
    
    

    lighting-app.ota should have greater software version which is defined by macro CHIP_DEVICE_CONFIG_DEVICE_SOFTWARE_VERSION in CHIPProjectConfig.h

Start ota-provider-app

  • Start ota-provider-app for lighting-app.ota

    $ rm -r /tmp/chip_*
    $ ./chip-ota-provider-app -f <path_to_ota_bin>/lighting-app.ota
    

    where <path_to_ota_bin> is the folder for lighting-app.ota.

  • Provision ota-provider-app with assigned node id to 1

    $ ./chip-tool pairing onnetwork 1 20202021
    $ ./chip-tool accesscontrol write acl '[{"fabricIndex": 1, "privilege": 5, "authMode": 2, "subjects": [112233], "targets": null}, {"fabricIndex": 1, "privilege": 3, "authMode": 2, "subjects": null, "targets": null}]' 1 0
    

Start ota software upgrade

  • BLE commission BL602/BL702 lighting if not commissioned.
  • Start OTA software upgrade process
    ./chip-tool otasoftwareupdaterequestor announce-ota-provider 1 0 0 0 <node_id_to_lighting_app> 0
    
    where <node_id_to_lighting_app> is node id of BL602/BL702 lighting app.
  • After OTA software upgrade gets done, BL602/BL702 will get reboot automatically.

Run RPC Console

  • Build chip-console following this guide

  • Start the console

    $ chip-console --device /dev/ttyUSB0 -b 2000000
    
  • Get or Set the light state

    rpcs.chip.rpc.Lighting.Get()

    rpcs.chip.rpc.Lighting.Set(on=True, level=128)