| /* |
| * Copyright (c) 2016-2019 Arm Limited. All rights reserved. |
| * |
| * Licensed under the Apache License, Version 2.0 (the "License"); |
| * you may not use this file except in compliance with the License. |
| * You may obtain a copy of the License at |
| * |
| * http://www.apache.org/licenses/LICENSE-2.0 |
| * |
| * Unless required by applicable law or agreed to in writing, software |
| * distributed under the License is distributed on an "AS IS" BASIS, |
| * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| * See the License for the specific language governing permissions and |
| * limitations under the License. |
| */ |
| |
| /** |
| * \file mpc_sie_drv.h |
| * \brief Generic driver for ARM SIE Memory Protection |
| * Controllers (MPC). |
| */ |
| |
| #ifndef __MPC_SIE_DRV_H__ |
| #define __MPC_SIE_DRV_H__ |
| |
| #include <stdbool.h> |
| #include <stdint.h> |
| |
| #ifdef __cplusplus |
| extern "C" { |
| #endif |
| |
| /* Error code returned by the driver functions */ |
| enum mpc_sie_error_t |
| { |
| MPC_SIE_ERR_NONE, /*!< No error */ |
| MPC_SIE_INVALID_ARG, /*!< MPC invalid input arguments */ |
| MPC_SIE_NOT_INIT, /*!< MPC not initialized */ |
| MPC_SIE_ERR_NOT_IN_RANGE, /*!< Address does not belong to a range |
| * controlled by the MPC */ |
| MPC_SIE_ERR_NOT_ALIGNED, /*!< Address is not aligned on the block size |
| * of this MPC |
| */ |
| MPC_SIE_ERR_INVALID_RANGE, /*!< The given address range to configure |
| * is invalid. This could be because: |
| * - The base and limit swapped |
| * - The base and limit addresses |
| * are in different ranges |
| */ |
| MPC_SIE_ERR_RANGE_SEC_ATTR_NON_COMPATIBLE, /*!< The given range cannot be |
| * accessed with the wanted |
| * security attributes |
| */ |
| MPC_SIE_UNSUPPORTED_HARDWARE_VERSION, /*!< MPC hardware version read from |
| * PIDR0 is not supported |
| */ |
| MPC_SIE_ERR_GATING_NOT_PRESENT /*!< MPC gating not present in HW */ |
| }; |
| |
| /* Security attribute used in various place of the API */ |
| enum mpc_sie_sec_attr_t |
| { |
| MPC_SIE_SEC_ATTR_SECURE, /*!< Secure attribute */ |
| MPC_SIE_SEC_ATTR_NONSECURE, /*!< Non-secure attribute */ |
| /*!< Used when getting the configuration of a memory range and some blocks |
| * are secure whereas some other are non secure |
| */ |
| MPC_SIE_SEC_ATTR_MIXED, |
| }; |
| |
| /* What can happen when trying to do an illegal memory access */ |
| enum mpc_sie_sec_resp_t |
| { |
| MPC_SIE_RESP_RAZ_WI, /*!< Read As Zero, Write Ignored */ |
| MPC_SIE_RESP_BUS_ERROR, /*!< Bus error */ |
| MPC_SIE_RESP_WAIT_GATING_DISABLED /*!< Wait until gating is disabled */ |
| }; |
| |
| /* Description of a memory range controlled by the MPC */ |
| struct mpc_sie_memory_range_t |
| { |
| const uint32_t base; /*!< Base address (included in the range) */ |
| const uint32_t limit; /*!< Limit address (included in the range) */ |
| const uint32_t range_offset; /*!< Offset of current range area to the 0 |
| * point of the whole area (the sum of the |
| * sizes of the previous memory ranges |
| * covered by the same MPC) |
| */ |
| const enum mpc_sie_sec_attr_t attr; /*!< Optional security attribute |
| * needed to be matched when |
| * accessing this range. |
| * For example, the non-secure |
| * alias of a memory region can not |
| * be accessed using secure access, |
| * and configuring the MPC to |
| * secure using that range will not |
| * be permitted by the driver. |
| */ |
| }; |
| |
| /* ARM MPC SIE device configuration structure */ |
| struct mpc_sie_dev_cfg_t |
| { |
| const uint32_t base; /*!< MPC base address */ |
| }; |
| |
| /* ARM MPC SIE device data structure */ |
| struct mpc_sie_dev_data_t |
| { |
| /*!< Array of pointers to memory ranges controlled by the MPC */ |
| const struct mpc_sie_memory_range_t ** range_list; |
| uint8_t nbr_of_ranges; /*!< Number of memory ranges in the list */ |
| bool is_initialized; /*!< Indicates if the MPC driver |
| * is initialized and enabled |
| */ |
| uint32_t sie_version; /*!< SIE version */ |
| }; |
| |
| /* ARM MPC SIE device structure */ |
| struct mpc_sie_dev_t |
| { |
| const struct mpc_sie_dev_cfg_t * const cfg; /*!< MPC configuration */ |
| struct mpc_sie_dev_data_t * const data; /*!< MPC data */ |
| }; |
| |
| /** |
| * \brief Initializes a MPC device. |
| * |
| * \param[in] dev MPC device \ref mpc_sie_dev_t |
| * \param[in] range_list List of memory ranges controller by the MPC |
| * (\ref mpc_sie_memory_range_t). This list can not |
| * freed after the initializations. |
| * \param[in] nbr_of_ranges Number of memory ranges |
| * |
| * \return Returns error code as specified in \ref mpc_sie_error_t |
| * |
| * \note This function doesn't check if dev is NULL. |
| */ |
| enum mpc_sie_error_t mpc_sie_init(struct mpc_sie_dev_t * dev, const struct mpc_sie_memory_range_t ** range_list, |
| uint8_t nbr_of_ranges); |
| |
| /** |
| * \brief Gets MPC block size. All regions must be aligned on this block |
| * size (base address and limit+1 address). |
| * |
| * \param[in] dev MPC device \ref mpc_sie_dev_t |
| * \param[out] blk_size MPC block size |
| * |
| * \return Returns error code as specified in \ref mpc_sie_error_t |
| * |
| * \note This function doesn't check if dev is NULL. |
| */ |
| enum mpc_sie_error_t mpc_sie_get_block_size(struct mpc_sie_dev_t * dev, uint32_t * blk_size); |
| |
| /** |
| * \brief Configures a memory region (base and limit included). |
| * |
| * \param[in] dev MPC device \ref mpc_sie_dev_t |
| * \param[in] base Base address of the region to poll. This bound is |
| * included. It does not need to be aligned in any way. |
| * |
| * \param[in] limit Limit address of the region to poll. This bound is |
| * included. (limit+1) does not need to be aligned |
| * in any way. |
| * \param[in] attr Security attribute of the region. If the region has mixed |
| * secure/non-secure, a special value is returned |
| * (\ref mpc_sie_sec_attr_t). |
| * |
| * In case base and limit+1 addresses are not aligned on |
| * the block size, the enclosing region with base and |
| * limit+1 aligned on block size will be queried. |
| * In case of early termination of the function (error), the |
| * security attribute will be set to MPC_SIE_ATTR_MIXED. |
| * |
| * \return Returns error code as specified in \ref mpc_sie_error_t |
| * |
| * \note This function doesn't check if dev is NULL. |
| */ |
| enum mpc_sie_error_t mpc_sie_config_region(struct mpc_sie_dev_t * dev, const uint32_t base, const uint32_t limit, |
| enum mpc_sie_sec_attr_t attr); |
| |
| /** |
| * \brief Gets a memory region configuration(base and limit included). |
| * |
| * \param[in] dev MPC device \ref mpc_sie_dev_t |
| * \param[in] base Base address of the region to get the configuration. |
| * \param[in] limit Limit address of the region to get the configuration. |
| * \param[out] attr Security attribute of the region |
| * \ref mpc_sie_sec_attr_t |
| * |
| * \return Returns error code as specified in \ref mpc_sie_error_t |
| * |
| * \note This function doesn't check if dev is NULL. |
| */ |
| enum mpc_sie_error_t mpc_sie_get_region_config(struct mpc_sie_dev_t * dev, uint32_t base, uint32_t limit, |
| enum mpc_sie_sec_attr_t * attr); |
| |
| /** |
| * \brief Gets the MPC control value. |
| * |
| * \param[in] dev MPC device \ref mpc_sie_dev_t |
| * \param[out] ctrl_val Current MPC control value. |
| * |
| * \return Returns error code as specified in \ref mpc_sie_error_t |
| * |
| * \note This function doesn't check if dev is NULL. |
| */ |
| enum mpc_sie_error_t mpc_sie_get_ctrl(struct mpc_sie_dev_t * dev, uint32_t * ctrl_val); |
| |
| /** |
| * \brief Sets the MPC control value. |
| * |
| * \param[in] dev MPC device \ref mpc_sie_dev_t |
| * \param[in] mpc_ctrl New MPC control value |
| * |
| * \return Returns error code as specified in \ref mpc_sie_error_t |
| * |
| * \note This function doesn't check if dev is NULL. |
| */ |
| enum mpc_sie_error_t mpc_sie_set_ctrl(struct mpc_sie_dev_t * dev, uint32_t mpc_ctrl); |
| |
| /** |
| * \brief Gets the configured secure response. |
| * |
| * \param[in] dev MPC device \ref mpc_sie_dev_t |
| * \param[out] sec_rep Configured secure response (\ref mpc_sie_sec_resp_t). |
| * |
| * \return Returns error code as specified in \ref mpc_sie_error_t |
| * |
| * \note This function doesn't check if dev is NULL. |
| */ |
| enum mpc_sie_error_t mpc_sie_get_sec_resp(struct mpc_sie_dev_t * dev, enum mpc_sie_sec_resp_t * sec_rep); |
| |
| /** |
| * \brief Sets the response type when SW asks to gate the incoming transfers. |
| * |
| * \param[in] dev MPC device \ref mpc_sie_dev_t |
| * \param[in] sec_rep Secure response to configure (\ref mpc_sie_sec_resp_t). |
| * |
| * \note This function doesn't check if dev is NULL. |
| */ |
| enum mpc_sie_error_t mpc_sie_set_sec_resp(struct mpc_sie_dev_t * dev, enum mpc_sie_sec_resp_t sec_rep); |
| |
| /** |
| * \brief Enables MPC interrupt. |
| * |
| * \param[in] dev MPC device \ref mpc_sie_dev_t |
| * |
| * \return Returns error code as specified in \ref mpc_sie_error_t |
| * |
| * \note This function doesn't check if dev is NULL. |
| */ |
| enum mpc_sie_error_t mpc_sie_irq_enable(struct mpc_sie_dev_t * dev); |
| |
| /** |
| * \brief Disables MPC interrupt |
| * |
| * \param[in] dev MPC device \ref mpc_sie_dev_t |
| * |
| * \note This function doesn't check if dev is NULL. |
| */ |
| void mpc_sie_irq_disable(struct mpc_sie_dev_t * dev); |
| |
| /** |
| * \brief Clears MPC interrupt. |
| * |
| * \param[in] dev MPC device \ref mpc_sie_dev_t |
| * |
| * \note This function doesn't check if dev is NULL. |
| */ |
| void mpc_sie_clear_irq(struct mpc_sie_dev_t * dev); |
| |
| /** |
| * \brief Returns the MPC interrupt state. |
| * |
| * \param[in] dev MPC device \ref mpc_sie_dev_t |
| * |
| * \return Returns 1 if the interrupt is active, 0 otherwise. |
| * |
| * \note This function doesn't check if dev is NULL. |
| */ |
| uint32_t mpc_sie_irq_state(struct mpc_sie_dev_t * dev); |
| |
| /** |
| * \brief Locks down the MPC configuration. |
| * |
| * \param[in] dev MPC device \ref mpc_sie_dev_t |
| * |
| * \return Returns error code as specified in \ref mpc_sie_error_t |
| * |
| * \note This function doesn't check if dev is NULL. |
| */ |
| enum mpc_sie_error_t mpc_sie_lock_down(struct mpc_sie_dev_t * dev); |
| |
| /** |
| * \brief Returns if gating is present in hardware. |
| * |
| * \param[in] dev MPC device \ref mpc_sie_dev_t |
| * \param[out] gating_present Returns if gating is present in hardware. |
| * |
| * \return Returns error code as specified in \ref mpc_sie_error_t |
| * |
| * \note This function doesn't check if dev is NULL. |
| */ |
| enum mpc_sie_error_t mpc_sie_is_gating_present(struct mpc_sie_dev_t * dev, bool * gating_present); |
| |
| /** |
| * \brief Returns the value of Peripheral ID 0 register. |
| * |
| * \param[in] dev MPC device \ref mpc_sie_dev_t |
| * |
| * \return Returns the value of Peripheral ID 0 register. |
| * |
| * \note This function doesn't check if dev is NULL. |
| */ |
| uint32_t get_sie_version(struct mpc_sie_dev_t * dev); |
| |
| /** |
| * \brief Reads bit indicating acknowledge for gating incoming transfers. |
| * |
| * \param[in] dev MPC device \ref mpc_sie_dev_t |
| * |
| * \return True if acknowledge is set. |
| * |
| * \note This function doesn't check if dev is NULL. |
| */ |
| bool mpc_sie_get_gate_ack(struct mpc_sie_dev_t * dev); |
| |
| /** |
| * \brief Sets bit to request for gating incoming transfers. |
| * |
| * \param[in] dev MPC device \ref mpc_sie_dev_t |
| * |
| * \note This function doesn't check if dev is NULL. |
| */ |
| void mpc_sie_request_gating(struct mpc_sie_dev_t * dev); |
| |
| /** |
| * \brief Clears bit to request for gating incoming transfers. |
| * |
| * \param[in] dev MPC device \ref mpc_sie_dev_t |
| * |
| * \note This function doesn't check if dev is NULL. |
| */ |
| void mpc_sie_release_gating(struct mpc_sie_dev_t * dev); |
| |
| #ifdef __cplusplus |
| } |
| #endif |
| #endif /* __MPC_SIE_DRV_H__ */ |