examples/platform/silabs/uart.cpp - third_party/github/project-chip/connectedhomeip - Git at Google

 /*
  *
  *    Copyright (c) 2021 Project CHIP Authors
  *    All rights reserved.
  *
  *    Licensed under the Apache License, Version 2.0 (the "License");
  *    you may not use this file except in compliance with the License.
  *    You may obtain a copy of the License at
  *
  *        http://www.apache.org/licenses/LICENSE-2.0
  *
  *    Unless required by applicable law or agreed to in writing, software
  *    distributed under the License is distributed on an "AS IS" BASIS,
  *    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
  *    See the License for the specific language governing permissions and
  *    limitations under the License.
  */
 #include "AppConfig.h"
 #ifdef ENABLE_CHIP_SHELL
 #include "MatterShell.h" // nogncheck
 #endif
 #include <cmsis_os2.h>
 #include <platform/CHIPDeviceLayer.h>
 #include <sl_cmsis_os2_common.h>

 #ifdef __cplusplus
 extern "C" {
 #endif

 #include "uart.h"
 #include <stddef.h>
 #include <string.h>

 #define UART_CONSOLE_ERR -1 // Negative value in case of UART Console action failed. Triggers a failure for PW_RPC
 #define MAX_BUFFER_SIZE 256
 #define MAX_DMA_BUFFER_SIZE (MAX_BUFFER_SIZE / 2)

 #if SLI_SI91X_MCU_INTERFACE
 #include "USART.h"
 #include "rsi_board.h"
 #include "rsi_debug.h"
 #include "rsi_rom_egpio.h"
 #else // For EFR32
 #if (_SILICON_LABS_32B_SERIES < 3)
 #include "em_core.h"
 #include "em_usart.h"
 #else
 #include "sl_hal_eusart.h"
 #endif //_SILICON_LABS_32B_SERIES
 #include "uartdrv.h"
 #ifdef SL_BOARD_NAME
 #include "sl_board_control.h"
 #endif
 #include "sl_uartdrv_instances.h"
 #if SL_WIFI
 #include "spi_multiplex.h"
 #endif // SL_WIFI
 #ifdef SL_CATALOG_UARTDRV_EUSART_PRESENT
 #include "sl_uartdrv_eusart_vcom_config.h"
 #endif
 #ifdef SL_CATALOG_UARTDRV_USART_PRESENT
 #include "sl_uartdrv_usart_vcom_config.h"
 #endif // SL_CATALOG_UARTDRV_USART_PRESENT

 #if defined(SL_CATALOG_POWER_MANAGER_PRESENT)
 #include "sl_power_manager.h"
 #endif

 #ifdef SL_CATALOG_UARTDRV_EUSART_PRESENT
 #define HELPER1(x) EUSART##x##_RX_IRQn
 #else
 #define HELPER1(x) USART##x##_RX_IRQn
 #endif

 #define HELPER2(x) HELPER1(x)

 #ifdef SL_CATALOG_UARTDRV_EUSART_PRESENT
 #define HELPER3(x) EUSART##x##_RX_IRQHandler
 #else
 #define HELPER3(x) USART##x##_RX_IRQHandler
 #endif

 #define HELPER4(x) HELPER3(x)

 // On MG24 boards VCOM runs on the EUSART device, MG12 uses the UART device
 #ifdef SL_CATALOG_UARTDRV_EUSART_PRESENT
 #define USART_IRQ HELPER2(SL_UARTDRV_EUSART_VCOM_PERIPHERAL_NO)
 #define USART_IRQHandler HELPER4(SL_UARTDRV_EUSART_VCOM_PERIPHERAL_NO)
 #define vcom_handle sl_uartdrv_eusart_vcom_handle

 #if (_SILICON_LABS_32B_SERIES < 3)
 #define EUSART_INT_ENABLE EUSART_IntEnable
 #define EUSART_INT_DISABLE EUSART_IntDisable
 #define EUSART_INT_CLEAR EUSART_IntClear
 #define EUSART_CLEAR_RX
 #define EUSART_GET_PENDING_INT EUSART_IntGet
 #define EUSART_ENABLE(eusart) EUSART_Enable(eusart, eusartEnable)
 #else
 #define EUSART_INT_ENABLE sl_hal_eusart_enable_interrupts
 #define EUSART_INT_DISABLE sl_hal_eusart_disable_interrupts
 #define EUSART_INT_SET sl_hal_eusart_set_interrupts
 #define EUSART_INT_CLEAR sl_hal_eusart_clear_interrupts
 #define EUSART_CLEAR_RX sl_hal_eusart_clear_rx
 #define EUSART_GET_PENDING_INT sl_hal_eusart_get_pending_interrupts
 #define EUSART_ENABLE(eusart)                                                                                                      \
     {                                                                                                                              \
         sl_hal_eusart_enable(eusart);                                                                                              \
         sl_hal_eusart_enable_tx(eusart);                                                                                           \
         sl_hal_eusart_enable_rx(eusart);                                                                                           \
     }
 #endif //_SILICON_LABS_32B_SERIES

 #else
 #define USART_IRQ HELPER2(SL_UARTDRV_USART_VCOM_PERIPHERAL_NO)
 #define USART_IRQHandler HELPER4(SL_UARTDRV_USART_VCOM_PERIPHERAL_NO)
 #define vcom_handle sl_uartdrv_usart_vcom_handle
 #endif // SL_CATALOG_UARTDRV_EUSART_PRESENT

 namespace {
 // In order to reduce the probability of data loss during the dmaFull callback handler we use
 // two duplicate receive buffers so we can always have one "active" receive queue.
 uint8_t sRxDmaBuffer[MAX_DMA_BUFFER_SIZE]  = { 0 };
 uint8_t sRxDmaBuffer2[MAX_DMA_BUFFER_SIZE] = { 0 };
 uint16_t lastCount                         = 0; // Nb of bytes already processed from the active dmaBuffer
 } // namespace

 #endif // SLI_SI91X_MCU_INTERFACE

 typedef struct
 {
     // The data buffer
     uint8_t * pBuffer;
     // The offset of the first item written to the list.
     volatile uint16_t Head;
     // The offset of the next item to be written to the list.
     volatile uint16_t Tail;
     // Maxium size of data that can be hold in buffer before overwriting
     uint16_t MaxSize;
 } Fifo_t;

 // uart transmit
 #if SILABS_LOG_OUT_UART
 #define UART_MAX_QUEUE_SIZE 125
 #else
 #if (_SILICON_LABS_32B_SERIES < 3)
 #define UART_MAX_QUEUE_SIZE 25
 #else
 #define UART_MAX_QUEUE_SIZE 50
 #endif
 #endif

 #ifdef CHIP_CONFIG_LOG_MESSAGE_MAX_SIZE
 #define UART_TX_MAX_BUF_LEN (CHIP_CONFIG_LOG_MESSAGE_MAX_SIZE + 2) // \r\n
 #else
 #define UART_TX_MAX_BUF_LEN (258)
 #endif

 static constexpr uint32_t kUartTxCompleteFlag = 1;
 static osThreadId_t sUartTaskHandle;
 constexpr uint32_t kUartTaskSize = 1024;
 static uint8_t uartStack[kUartTaskSize];
 static osThread_t sUartTaskControlBlock;
 constexpr osThreadAttr_t kUartTaskAttr = { .name       = "UART",
                                            .attr_bits  = osThreadDetached,
                                            .cb_mem     = &sUartTaskControlBlock,
                                            .cb_size    = osThreadCbSize,
                                            .stack_mem  = uartStack,
                                            .stack_size = kUartTaskSize,
                                            .priority   = osPriorityBelowNormal };

 typedef struct
 {
     uint8_t data[UART_TX_MAX_BUF_LEN];
     uint16_t length = 0;
 } UartTxStruct_t;

 static osMessageQueueId_t sUartTxQueue;
 static osMessageQueue_t sUartTxQueueStruct;
 uint8_t sUartTxQueueBuffer[UART_MAX_QUEUE_SIZE * sizeof(UartTxStruct_t)];
 constexpr osMessageQueueAttr_t kUartTxQueueAttr = { .cb_mem  = &sUartTxQueueStruct,
                                                     .cb_size = osMessageQueueCbSize,
                                                     .mq_mem  = sUartTxQueueBuffer,
                                                     .mq_size = sizeof(sUartTxQueueBuffer) };

 // Rx buffer for the receive Fifo
 static uint8_t sRxFifoBuffer[MAX_BUFFER_SIZE];
 static Fifo_t sReceiveFifo;

 #if SLI_SI91X_MCU_INTERFACE == 0
 static void UART_rx_callback(UARTDRV_Handle_t handle, Ecode_t transferStatus, uint8_t * data, UARTDRV_Count_t transferCount);
 #endif // SLI_SI91X_MCU_INTERFACE == 0
 static void uartSendBytes(uint8_t * buffer, uint16_t nbOfBytes);

 static bool InitFifo(Fifo_t * fifo, uint8_t * pDataBuffer, uint16_t bufferSize)
 {
     if (fifo == NULL || pDataBuffer == NULL)
     {
         return false;
     }

     fifo->pBuffer = pDataBuffer;
     fifo->MaxSize = bufferSize;
     fifo->Tail = fifo->Head = 0;

     return true;
 }

 /*
  *   @brief Get the amount of unprocessed bytes in the fifo buffer
  *   @param Ptr to the fifo
  *   @return Nb of "unread" bytes available in the fifo
  */
 static uint16_t AvailableDataCount(Fifo_t * fifo)
 {
     uint16_t size = 0;

     // if equal there is no data return 0 directly
     if (fifo->Tail != fifo->Head)
     {
         // determine if a wrap around occurred to get the right data size avalaible.
         size = (fifo->Tail < fifo->Head) ? (fifo->MaxSize - fifo->Head + fifo->Tail) : (fifo->Tail - fifo->Head);
     }

     return size;
 }

 /*
  *   @brief Get the available space in the fifo buffer to insert new data
  *   @param Ptr to the fifo
  *   @return Nb of free bytes left in te buffer
  */
 static uint16_t RemainingSpace(Fifo_t * fifo)
 {
     return fifo->MaxSize - AvailableDataCount(fifo);
 }

 /*
  *   @brief Write data in the fifo as a circular buffer
  *   @param Ptr to the fifo, ptr of the data to write, nb of bytes to write
  */
 static void WriteToFifo(Fifo_t * fifo, uint8_t * pDataToWrite, uint16_t SizeToWrite)
 {
     VerifyOrDie(fifo != nullptr);
     VerifyOrDie(pDataToWrite != nullptr);
     VerifyOrDie(SizeToWrite <= fifo->MaxSize);

     // Overwrite is not allowed
     if (RemainingSpace(fifo) >= SizeToWrite)
     {
         uint16_t nBytesBeforWrap = (fifo->MaxSize - fifo->Tail);
         if (SizeToWrite > nBytesBeforWrap)
         {
             // The number of bytes to write is bigger than the remaining bytes
             // in the buffer, we have to wrap around
             memcpy(fifo->pBuffer + fifo->Tail, pDataToWrite, nBytesBeforWrap);
             memcpy(fifo->pBuffer, pDataToWrite + nBytesBeforWrap, SizeToWrite - nBytesBeforWrap);
         }
         else
         {
             memcpy(fifo->pBuffer + fifo->Tail, pDataToWrite, SizeToWrite);
         }

         fifo->Tail = (fifo->Tail + SizeToWrite) % fifo->MaxSize; // increment tail with wraparound
     }
 }

 /*
  *   @brief Write data in the fifo as a circular buffer
  *   @param Ptr to the fifo, ptr to contain the data to process, nb of bytes to pull from the fifo
  *   @return Nb of bytes that were retrieved.
  */
 static uint16_t RetrieveFromFifo(Fifo_t * fifo, uint8_t * pData, uint16_t SizeToRead)
 {
     VerifyOrDie(fifo != nullptr);
     VerifyOrDie(pData != nullptr);
     VerifyOrDie(SizeToRead <= fifo->MaxSize);

     uint16_t ReadSize        = std::min(SizeToRead, AvailableDataCount(fifo));
     uint16_t nBytesBeforWrap = (fifo->MaxSize - fifo->Head);

     if (ReadSize > nBytesBeforWrap)
     {
         memcpy(pData, fifo->pBuffer + fifo->Head, nBytesBeforWrap);
         memcpy(pData + nBytesBeforWrap, fifo->pBuffer, ReadSize - nBytesBeforWrap);
     }
     else
     {
         memcpy(pData, (fifo->pBuffer + fifo->Head), ReadSize);
     }

     fifo->Head = (fifo->Head + ReadSize) % fifo->MaxSize; // increment tail with wraparound

     return ReadSize;
 }

 /*
  *   @brief Init the the UART for serial communication, Start DMA reception
  *          and init Fifo to handle the received data from this uart
  *
  *   @Note This UART is used for pigweed rpc
  */
 void uartConsoleInit(void)
 {
     if (sUartTaskHandle != NULL)
     {
         // Init was already done
         return;
     }

     sUartTxQueue    = osMessageQueueNew(UART_MAX_QUEUE_SIZE, sizeof(UartTxStruct_t), &kUartTxQueueAttr);
     sUartTaskHandle = osThreadNew(uartMainLoop, nullptr, &kUartTaskAttr);

     // Init a fifo for the data received on the uart
     InitFifo(&sReceiveFifo, sRxFifoBuffer, MAX_BUFFER_SIZE);

     VerifyOrDie(sUartTaskHandle != nullptr);
     VerifyOrDie(sUartTxQueue != nullptr);

 #if SLI_SI91X_MCU_INTERFACE == 0
 #ifdef SL_BOARD_NAME
     sl_board_enable_vcom();
 #endif

     // Activate 2 dma queues to always have one active
     UARTDRV_Receive(vcom_handle, sRxDmaBuffer, MAX_DMA_BUFFER_SIZE, UART_rx_callback);
     UARTDRV_Receive(vcom_handle, sRxDmaBuffer2, MAX_DMA_BUFFER_SIZE, UART_rx_callback);

     // Enable USART0/EUSART0 interrupt to wake OT task when data arrives
     NVIC_ClearPendingIRQ(USART_IRQ);
     NVIC_EnableIRQ(USART_IRQ);

 #ifdef SL_CATALOG_UARTDRV_EUSART_PRESENT
     // Clear previous RX interrupts
     EUSART_INT_CLEAR(SL_UARTDRV_EUSART_VCOM_PERIPHERAL, (EUSART_IF_RXFL | EUSART_IF_RXOF));
     EUSART_CLEAR_RX(SL_UARTDRV_EUSART_VCOM_PERIPHERAL);

     // Enable RX interrupts
     EUSART_INT_ENABLE(SL_UARTDRV_EUSART_VCOM_PERIPHERAL, EUSART_IF_RXFL);

     // Enable EUSART
     EUSART_ENABLE(SL_UARTDRV_EUSART_VCOM_PERIPHERAL);
 #else
     USART_IntEnable(SL_UARTDRV_USART_VCOM_PERIPHERAL, USART_IF_RXDATAV);
 #endif // SL_CATALOG_UARTDRV_EUSART_PRESENT
 #endif // SLI_SI91X_MCU_INTERFACE == 0
 }

 #if SLI_SI91X_MCU_INTERFACE
 void cache_uart_rx_data(char character)
 {
     if (RemainingSpace(&sReceiveFifo) >= 1)
     {
         WriteToFifo(&sReceiveFifo, (uint8_t *) &character, 1);
     }
 #ifdef ENABLE_CHIP_SHELL
     chip::NotifyShellProcess();
 #endif // ENABLE_CHIP_SHELL
 }
 #endif // SLI_SI91X_MCU_INTERFACE

 #if SLI_SI91X_MCU_INTERFACE == 0
 // For EFR32
 void USART_IRQHandler(void)
 {
 #ifdef ENABLE_CHIP_SHELL
     chip::NotifyShellProcess();
 #elif !defined(PW_RPC_ENABLED) && !defined(SL_WIFI)
     otSysEventSignalPending();
 #endif
 #ifdef SL_CATALOG_UARTDRV_EUSART_PRESENT
     // disable RXFL IRQ until data read by uartConsoleRead
     EUSART_INT_DISABLE(SL_UARTDRV_EUSART_VCOM_PERIPHERAL, EUSART_IF_RXFL);
     EUSART_INT_CLEAR(SL_UARTDRV_EUSART_VCOM_PERIPHERAL, EUSART_IF_RXFL);

     if (EUSART_GET_PENDING_INT(SL_UARTDRV_EUSART_VCOM_PERIPHERAL) & EUSART_IF_RXOF)
     {
         EUSART_CLEAR_RX(SL_UARTDRV_EUSART_VCOM_PERIPHERAL);
     }
 #endif
 }

 /**
  * @brief Transmit complete callback
  *
  * @param handle
  * @param transferStatus
  * @param data
  * @param transferCount
  */
 void UART_tx_callback(struct UARTDRV_HandleData * handle, Ecode_t transferStatus, uint8_t * data, UARTDRV_Count_t transferCount)
 {
     // This function may be called from Interrupt Service Routines.
     osThreadFlagsSet(sUartTaskHandle, kUartTxCompleteFlag);
 }

 /*
  *   @brief Callback triggered when a UARTDRV DMA buffer is full
  */
 static void UART_rx_callback(UARTDRV_Handle_t handle, Ecode_t transferStatus, uint8_t * data, UARTDRV_Count_t transferCount)
 {
     (void) transferStatus;

     uint8_t writeSize = (transferCount - lastCount);
     if (RemainingSpace(&sReceiveFifo) >= writeSize)
     {
         WriteToFifo(&sReceiveFifo, data + lastCount, writeSize);
         lastCount = 0;
     }

     UARTDRV_Receive(vcom_handle, data, transferCount, UART_rx_callback);

 #ifdef ENABLE_CHIP_SHELL
     chip::NotifyShellProcess();
 #elif !defined(PW_RPC_ENABLED)
     otSysEventSignalPending();
 #endif
 }
 #endif // SLI_SI91X_MCU_INTERFACE == 0

 /**
  * @brief Read the data available from the console Uart
  *
  * @param Buf Buffer that contains the data to write
  * @param BufLength number bytes to write
  * @return int16_t Amount of bytes written or ERROR (-1)
  */
 int16_t uartConsoleWrite(const char * Buf, uint16_t BufLength)
 {
     if (Buf == NULL || BufLength < 1 || BufLength > UART_TX_MAX_BUF_LEN)
     {
         return UART_CONSOLE_ERR;
     }

     if (NULL == sUartTxQueue)
     {
         // This is to prevent the first prompt from OTCLI to be rejected and to break the OTCli output
         uartConsoleInit();
     }

 #ifdef PW_RPC_ENABLED
     // Pigweed Logger is already thread safe.
     UARTDRV_ForceTransmit(vcom_handle, (uint8_t *) Buf, BufLength);
     return BufLength;
 #endif

     UartTxStruct_t workBuffer;
     memcpy(workBuffer.data, Buf, BufLength);
     workBuffer.length = BufLength;

     // this is usually a command response. Wait on queue if full.
     if (osMessageQueuePut(sUartTxQueue, &workBuffer, osPriorityNormal, osWaitForever) == osOK)
     {
         return BufLength;
     }

     return UART_CONSOLE_ERR;
 }

 /**
  * @brief Write Logs to the Uart. Appends a return character
  *
  * @param log pointer to the logs
  * @param length number of bytes to write
  * @return int16_t Amount of bytes written or ERROR (-1)
  */
 int16_t uartLogWrite(const char * log, uint16_t length)
 {
     if (log == NULL || length < 1 || (length + 2) > UART_TX_MAX_BUF_LEN)
     {
         return UART_CONSOLE_ERR;
     }

     UartTxStruct_t workBuffer;
     memcpy(workBuffer.data, log, length);
     memcpy(workBuffer.data + length, "\r\n", 2);
     workBuffer.length = length + 2;

     // Don't wait when queue is full. Drop the log and return UART_CONSOLE_ERR
     if (osMessageQueuePut(sUartTxQueue, &workBuffer, osPriorityNormal, 0) == osOK)
     {
         return length;
     }

     return UART_CONSOLE_ERR;
 }

 /*
  *   @brief Read the data available from the console Uart
  *   @param Buffer for the data to be read, number bytes to read.
  *   @return Amount of bytes that was read from the rx fifo or ERROR (-1)
  */
 int16_t uartConsoleRead(char * Buf, uint16_t NbBytesToRead)
 {
     uint8_t * data;

 #ifdef SL_CATALOG_UARTDRV_EUSART_PRESENT
     EUSART_INT_ENABLE(SL_UARTDRV_EUSART_VCOM_PERIPHERAL, EUSART_IF_RXFL);
 #endif

     if (Buf == NULL || NbBytesToRead < 1)
     {
         return UART_CONSOLE_ERR;
     }
 #if SLI_SI91X_MCU_INTERFACE == 0
     if (NbBytesToRead > AvailableDataCount(&sReceiveFifo))
     {
         UARTDRV_Count_t count, remaining;
         // Not enough data available in the fifo for the read size request
         // If there is data available in dma buffer, get it now.
         CORE_ATOMIC_SECTION(UARTDRV_GetReceiveStatus(vcom_handle, &data, &count, &remaining); if (count > lastCount) {
             WriteToFifo(&sReceiveFifo, data + lastCount, count - lastCount);
             lastCount = count;
         })
     }
 #endif // SLI_SI91X_MCU_INTERFACE == 0

     return (int16_t) RetrieveFromFifo(&sReceiveFifo, (uint8_t *) Buf, NbBytesToRead);
 }

 void uartMainLoop(void * args)
 {
     UartTxStruct_t workBuffer;

     while (1)
     {

         osStatus_t eventReceived = osMessageQueueGet(sUartTxQueue, &workBuffer, nullptr, osWaitForever);
         while (eventReceived == osOK)
         {
             uartSendBytes(workBuffer.data, workBuffer.length);
             eventReceived = osMessageQueueGet(sUartTxQueue, &workBuffer, nullptr, 0);
         }
     }
 }

 /**
  * @brief Send Bytes to UART. This blocks the UART task.
  *
  * @param buffer pointer to the buffer containing the data
  * @param nbOfBytes number of bytes to send
  */
 void uartSendBytes(uint8_t * buffer, uint16_t nbOfBytes)
 {
 #if SLI_SI91X_MCU_INTERFACE
     // ensuring null termination of buffer
     if (nbOfBytes != CHIP_SHELL_MAX_LINE_SIZE && buffer[nbOfBytes - 1] != '\0')
     {
         buffer[nbOfBytes] = '\0';
     }
     Board_UARTPutSTR(reinterpret_cast<uint8_t *>(buffer));
 #else
 #if defined(SL_CATALOG_POWER_MANAGER_PRESENT)
     sl_power_manager_add_em_requirement(SL_POWER_MANAGER_EM1);
 #endif // SL_CATALOG_POWER_MANAGER_PRESENT

 #if SL_UARTCTRL_MUX
     sl_wfx_host_pre_uart_transfer();
 #endif // SL_UARTCTRL_MUX

 #if (defined(EFR32MG24) && defined(WF200_WIFI))
     // Blocking transmit for the MG24 + WF200 since UART TX is multiplexed with
     // WF200 SPI IRQ
     UARTDRV_ForceTransmit(vcom_handle, (uint8_t *) buffer, nbOfBytes);
 #else
     // Non Blocking Transmit
     UARTDRV_Transmit(vcom_handle, (uint8_t *) buffer, nbOfBytes, UART_tx_callback);
     osThreadFlagsWait(kUartTxCompleteFlag, osFlagsWaitAny, osWaitForever);
 #endif /* EFR32MG24 && WF200_WIFI */

 #if SL_UARTCTRL_MUX
     sl_wfx_host_post_uart_transfer();
 #endif // SL_UARTCTRL_MUX

 #if defined(SL_CATALOG_POWER_MANAGER_PRESENT)
     sl_power_manager_remove_em_requirement(SL_POWER_MANAGER_EM1);
 #endif // SL_CATALOG_POWER_MANAGER_PRESENT
 #endif // SLI_SI91X_MCU_INTERFACE
 }

 #ifdef __cplusplus
 }
 #endif
	/*
	*
	* Copyright (c) 2021 Project CHIP Authors
	* All rights reserved.
	*
	* Licensed under the Apache License, Version 2.0 (the "License");
	* you may not use this file except in compliance with the License.
	* You may obtain a copy of the License at
	*
	* http://www.apache.org/licenses/LICENSE-2.0
	*
	* Unless required by applicable law or agreed to in writing, software
	* distributed under the License is distributed on an "AS IS" BASIS,
	* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
	* See the License for the specific language governing permissions and
	* limitations under the License.
	*/
	#include "AppConfig.h"
	#ifdef ENABLE_CHIP_SHELL
	#include "MatterShell.h" // nogncheck
	#endif
	#include <cmsis_os2.h>
	#include <platform/CHIPDeviceLayer.h>
	#include <sl_cmsis_os2_common.h>

	#ifdef __cplusplus
	extern "C" {
	#endif

	#include "uart.h"
	#include <stddef.h>
	#include <string.h>

	#define UART_CONSOLE_ERR -1 // Negative value in case of UART Console action failed. Triggers a failure for PW_RPC
	#define MAX_BUFFER_SIZE 256
	#define MAX_DMA_BUFFER_SIZE (MAX_BUFFER_SIZE / 2)

	#if SLI_SI91X_MCU_INTERFACE
	#include "USART.h"
	#include "rsi_board.h"
	#include "rsi_debug.h"
	#include "rsi_rom_egpio.h"
	#else // For EFR32
	#if (_SILICON_LABS_32B_SERIES < 3)
	#include "em_core.h"
	#include "em_usart.h"
	#else
	#include "sl_hal_eusart.h"
	#endif //_SILICON_LABS_32B_SERIES
	#include "uartdrv.h"
	#ifdef SL_BOARD_NAME
	#include "sl_board_control.h"
	#endif
	#include "sl_uartdrv_instances.h"
	#if SL_WIFI
	#include "spi_multiplex.h"
	#endif // SL_WIFI
	#ifdef SL_CATALOG_UARTDRV_EUSART_PRESENT
	#include "sl_uartdrv_eusart_vcom_config.h"
	#endif
	#ifdef SL_CATALOG_UARTDRV_USART_PRESENT
	#include "sl_uartdrv_usart_vcom_config.h"
	#endif // SL_CATALOG_UARTDRV_USART_PRESENT

	#if defined(SL_CATALOG_POWER_MANAGER_PRESENT)
	#include "sl_power_manager.h"
	#endif

	#ifdef SL_CATALOG_UARTDRV_EUSART_PRESENT
	#define HELPER1(x) EUSART##x##_RX_IRQn
	#else
	#define HELPER1(x) USART##x##_RX_IRQn
	#endif

	#define HELPER2(x) HELPER1(x)

	#ifdef SL_CATALOG_UARTDRV_EUSART_PRESENT
	#define HELPER3(x) EUSART##x##_RX_IRQHandler
	#else
	#define HELPER3(x) USART##x##_RX_IRQHandler
	#endif

	#define HELPER4(x) HELPER3(x)

	// On MG24 boards VCOM runs on the EUSART device, MG12 uses the UART device
	#ifdef SL_CATALOG_UARTDRV_EUSART_PRESENT
	#define USART_IRQ HELPER2(SL_UARTDRV_EUSART_VCOM_PERIPHERAL_NO)
	#define USART_IRQHandler HELPER4(SL_UARTDRV_EUSART_VCOM_PERIPHERAL_NO)
	#define vcom_handle sl_uartdrv_eusart_vcom_handle

	#if (_SILICON_LABS_32B_SERIES < 3)
	#define EUSART_INT_ENABLE EUSART_IntEnable
	#define EUSART_INT_DISABLE EUSART_IntDisable
	#define EUSART_INT_CLEAR EUSART_IntClear
	#define EUSART_CLEAR_RX
	#define EUSART_GET_PENDING_INT EUSART_IntGet
	#define EUSART_ENABLE(eusart) EUSART_Enable(eusart, eusartEnable)
	#else
	#define EUSART_INT_ENABLE sl_hal_eusart_enable_interrupts
	#define EUSART_INT_DISABLE sl_hal_eusart_disable_interrupts
	#define EUSART_INT_SET sl_hal_eusart_set_interrupts
	#define EUSART_INT_CLEAR sl_hal_eusart_clear_interrupts
	#define EUSART_CLEAR_RX sl_hal_eusart_clear_rx
	#define EUSART_GET_PENDING_INT sl_hal_eusart_get_pending_interrupts
	#define EUSART_ENABLE(eusart) \
	{ \
	sl_hal_eusart_enable(eusart); \
	sl_hal_eusart_enable_tx(eusart); \
	sl_hal_eusart_enable_rx(eusart); \
	}
	#endif //_SILICON_LABS_32B_SERIES

	#else
	#define USART_IRQ HELPER2(SL_UARTDRV_USART_VCOM_PERIPHERAL_NO)
	#define USART_IRQHandler HELPER4(SL_UARTDRV_USART_VCOM_PERIPHERAL_NO)
	#define vcom_handle sl_uartdrv_usart_vcom_handle
	#endif // SL_CATALOG_UARTDRV_EUSART_PRESENT

	namespace {
	// In order to reduce the probability of data loss during the dmaFull callback handler we use
	// two duplicate receive buffers so we can always have one "active" receive queue.
	uint8_t sRxDmaBuffer[MAX_DMA_BUFFER_SIZE] = { 0 };
	uint8_t sRxDmaBuffer2[MAX_DMA_BUFFER_SIZE] = { 0 };
	uint16_t lastCount = 0; // Nb of bytes already processed from the active dmaBuffer
	} // namespace

	#endif // SLI_SI91X_MCU_INTERFACE

	typedef struct
	{
	// The data buffer
	uint8_t * pBuffer;
	// The offset of the first item written to the list.
	volatile uint16_t Head;
	// The offset of the next item to be written to the list.
	volatile uint16_t Tail;
	// Maxium size of data that can be hold in buffer before overwriting
	uint16_t MaxSize;
	} Fifo_t;

	// uart transmit
	#if SILABS_LOG_OUT_UART
	#define UART_MAX_QUEUE_SIZE 125
	#else
	#if (_SILICON_LABS_32B_SERIES < 3)
	#define UART_MAX_QUEUE_SIZE 25
	#else
	#define UART_MAX_QUEUE_SIZE 50
	#endif
	#endif

	#ifdef CHIP_CONFIG_LOG_MESSAGE_MAX_SIZE
	#define UART_TX_MAX_BUF_LEN (CHIP_CONFIG_LOG_MESSAGE_MAX_SIZE + 2) // \r\n
	#else
	#define UART_TX_MAX_BUF_LEN (258)
	#endif

	static constexpr uint32_t kUartTxCompleteFlag = 1;
	static osThreadId_t sUartTaskHandle;
	constexpr uint32_t kUartTaskSize = 1024;
	static uint8_t uartStack[kUartTaskSize];
	static osThread_t sUartTaskControlBlock;
	constexpr osThreadAttr_t kUartTaskAttr = { .name = "UART",
	.attr_bits = osThreadDetached,
	.cb_mem = &sUartTaskControlBlock,
	.cb_size = osThreadCbSize,
	.stack_mem = uartStack,
	.stack_size = kUartTaskSize,
	.priority = osPriorityBelowNormal };

	typedef struct
	{
	uint8_t data[UART_TX_MAX_BUF_LEN];
	uint16_t length = 0;
	} UartTxStruct_t;

	static osMessageQueueId_t sUartTxQueue;
	static osMessageQueue_t sUartTxQueueStruct;
	uint8_t sUartTxQueueBuffer[UART_MAX_QUEUE_SIZE * sizeof(UartTxStruct_t)];
	constexpr osMessageQueueAttr_t kUartTxQueueAttr = { .cb_mem = &sUartTxQueueStruct,
	.cb_size = osMessageQueueCbSize,
	.mq_mem = sUartTxQueueBuffer,
	.mq_size = sizeof(sUartTxQueueBuffer) };

	// Rx buffer for the receive Fifo
	static uint8_t sRxFifoBuffer[MAX_BUFFER_SIZE];
	static Fifo_t sReceiveFifo;

	#if SLI_SI91X_MCU_INTERFACE == 0
	static void UART_rx_callback(UARTDRV_Handle_t handle, Ecode_t transferStatus, uint8_t * data, UARTDRV_Count_t transferCount);
	#endif // SLI_SI91X_MCU_INTERFACE == 0
	static void uartSendBytes(uint8_t * buffer, uint16_t nbOfBytes);

	static bool InitFifo(Fifo_t * fifo, uint8_t * pDataBuffer, uint16_t bufferSize)
	{
	if (fifo == NULL \|\| pDataBuffer == NULL)
	{
	return false;
	}

	fifo->pBuffer = pDataBuffer;
	fifo->MaxSize = bufferSize;
	fifo->Tail = fifo->Head = 0;

	return true;
	}

	/*
	* @brief Get the amount of unprocessed bytes in the fifo buffer
	* @param Ptr to the fifo
	* @return Nb of "unread" bytes available in the fifo
	*/
	static uint16_t AvailableDataCount(Fifo_t * fifo)
	{
	uint16_t size = 0;

	// if equal there is no data return 0 directly
	if (fifo->Tail != fifo->Head)
	{
	// determine if a wrap around occurred to get the right data size avalaible.
	size = (fifo->Tail < fifo->Head) ? (fifo->MaxSize - fifo->Head + fifo->Tail) : (fifo->Tail - fifo->Head);
	}

	return size;
	}

	/*
	* @brief Get the available space in the fifo buffer to insert new data
	* @param Ptr to the fifo
	* @return Nb of free bytes left in te buffer
	*/
	static uint16_t RemainingSpace(Fifo_t * fifo)
	{
	return fifo->MaxSize - AvailableDataCount(fifo);
	}

	/*
	* @brief Write data in the fifo as a circular buffer
	* @param Ptr to the fifo, ptr of the data to write, nb of bytes to write
	*/
	static void WriteToFifo(Fifo_t * fifo, uint8_t * pDataToWrite, uint16_t SizeToWrite)
	{
	VerifyOrDie(fifo != nullptr);
	VerifyOrDie(pDataToWrite != nullptr);
	VerifyOrDie(SizeToWrite <= fifo->MaxSize);

	// Overwrite is not allowed
	if (RemainingSpace(fifo) >= SizeToWrite)
	{
	uint16_t nBytesBeforWrap = (fifo->MaxSize - fifo->Tail);
	if (SizeToWrite > nBytesBeforWrap)
	{
	// The number of bytes to write is bigger than the remaining bytes
	// in the buffer, we have to wrap around
	memcpy(fifo->pBuffer + fifo->Tail, pDataToWrite, nBytesBeforWrap);
	memcpy(fifo->pBuffer, pDataToWrite + nBytesBeforWrap, SizeToWrite - nBytesBeforWrap);
	}
	else
	{
	memcpy(fifo->pBuffer + fifo->Tail, pDataToWrite, SizeToWrite);
	}

	fifo->Tail = (fifo->Tail + SizeToWrite) % fifo->MaxSize; // increment tail with wraparound
	}
	}

	/*
	* @brief Write data in the fifo as a circular buffer
	* @param Ptr to the fifo, ptr to contain the data to process, nb of bytes to pull from the fifo
	* @return Nb of bytes that were retrieved.
	*/
	static uint16_t RetrieveFromFifo(Fifo_t * fifo, uint8_t * pData, uint16_t SizeToRead)
	{
	VerifyOrDie(fifo != nullptr);
	VerifyOrDie(pData != nullptr);
	VerifyOrDie(SizeToRead <= fifo->MaxSize);

	uint16_t ReadSize = std::min(SizeToRead, AvailableDataCount(fifo));
	uint16_t nBytesBeforWrap = (fifo->MaxSize - fifo->Head);

	if (ReadSize > nBytesBeforWrap)
	{
	memcpy(pData, fifo->pBuffer + fifo->Head, nBytesBeforWrap);
	memcpy(pData + nBytesBeforWrap, fifo->pBuffer, ReadSize - nBytesBeforWrap);
	}
	else
	{
	memcpy(pData, (fifo->pBuffer + fifo->Head), ReadSize);
	}

	fifo->Head = (fifo->Head + ReadSize) % fifo->MaxSize; // increment tail with wraparound

	return ReadSize;
	}

	/*
	* @brief Init the the UART for serial communication, Start DMA reception
	* and init Fifo to handle the received data from this uart
	*
	* @Note This UART is used for pigweed rpc
	*/
	void uartConsoleInit(void)
	{
	if (sUartTaskHandle != NULL)
	{
	// Init was already done
	return;
	}

	sUartTxQueue = osMessageQueueNew(UART_MAX_QUEUE_SIZE, sizeof(UartTxStruct_t), &kUartTxQueueAttr);
	sUartTaskHandle = osThreadNew(uartMainLoop, nullptr, &kUartTaskAttr);

	// Init a fifo for the data received on the uart
	InitFifo(&sReceiveFifo, sRxFifoBuffer, MAX_BUFFER_SIZE);

	VerifyOrDie(sUartTaskHandle != nullptr);
	VerifyOrDie(sUartTxQueue != nullptr);

	#if SLI_SI91X_MCU_INTERFACE == 0
	#ifdef SL_BOARD_NAME
	sl_board_enable_vcom();
	#endif

	// Activate 2 dma queues to always have one active
	UARTDRV_Receive(vcom_handle, sRxDmaBuffer, MAX_DMA_BUFFER_SIZE, UART_rx_callback);
	UARTDRV_Receive(vcom_handle, sRxDmaBuffer2, MAX_DMA_BUFFER_SIZE, UART_rx_callback);

	// Enable USART0/EUSART0 interrupt to wake OT task when data arrives
	NVIC_ClearPendingIRQ(USART_IRQ);
	NVIC_EnableIRQ(USART_IRQ);

	#ifdef SL_CATALOG_UARTDRV_EUSART_PRESENT
	// Clear previous RX interrupts
	EUSART_INT_CLEAR(SL_UARTDRV_EUSART_VCOM_PERIPHERAL, (EUSART_IF_RXFL \| EUSART_IF_RXOF));
	EUSART_CLEAR_RX(SL_UARTDRV_EUSART_VCOM_PERIPHERAL);

	// Enable RX interrupts
	EUSART_INT_ENABLE(SL_UARTDRV_EUSART_VCOM_PERIPHERAL, EUSART_IF_RXFL);

	// Enable EUSART
	EUSART_ENABLE(SL_UARTDRV_EUSART_VCOM_PERIPHERAL);
	#else
	USART_IntEnable(SL_UARTDRV_USART_VCOM_PERIPHERAL, USART_IF_RXDATAV);
	#endif // SL_CATALOG_UARTDRV_EUSART_PRESENT
	#endif // SLI_SI91X_MCU_INTERFACE == 0
	}

	#if SLI_SI91X_MCU_INTERFACE
	void cache_uart_rx_data(char character)
	{
	if (RemainingSpace(&sReceiveFifo) >= 1)
	{
	WriteToFifo(&sReceiveFifo, (uint8_t *) &character, 1);
	}
	#ifdef ENABLE_CHIP_SHELL
	chip::NotifyShellProcess();
	#endif // ENABLE_CHIP_SHELL
	}
	#endif // SLI_SI91X_MCU_INTERFACE

	#if SLI_SI91X_MCU_INTERFACE == 0
	// For EFR32
	void USART_IRQHandler(void)
	{
	#ifdef ENABLE_CHIP_SHELL
	chip::NotifyShellProcess();
	#elif !defined(PW_RPC_ENABLED) && !defined(SL_WIFI)
	otSysEventSignalPending();
	#endif
	#ifdef SL_CATALOG_UARTDRV_EUSART_PRESENT
	// disable RXFL IRQ until data read by uartConsoleRead
	EUSART_INT_DISABLE(SL_UARTDRV_EUSART_VCOM_PERIPHERAL, EUSART_IF_RXFL);
	EUSART_INT_CLEAR(SL_UARTDRV_EUSART_VCOM_PERIPHERAL, EUSART_IF_RXFL);

	if (EUSART_GET_PENDING_INT(SL_UARTDRV_EUSART_VCOM_PERIPHERAL) & EUSART_IF_RXOF)
	{
	EUSART_CLEAR_RX(SL_UARTDRV_EUSART_VCOM_PERIPHERAL);
	}
	#endif
	}

	/**
	* @brief Transmit complete callback
	*
	* @param handle
	* @param transferStatus
	* @param data
	* @param transferCount
	*/
	void UART_tx_callback(struct UARTDRV_HandleData * handle, Ecode_t transferStatus, uint8_t * data, UARTDRV_Count_t transferCount)
	{
	// This function may be called from Interrupt Service Routines.
	osThreadFlagsSet(sUartTaskHandle, kUartTxCompleteFlag);
	}

	/*
	* @brief Callback triggered when a UARTDRV DMA buffer is full
	*/
	static void UART_rx_callback(UARTDRV_Handle_t handle, Ecode_t transferStatus, uint8_t * data, UARTDRV_Count_t transferCount)
	{
	(void) transferStatus;

	uint8_t writeSize = (transferCount - lastCount);
	if (RemainingSpace(&sReceiveFifo) >= writeSize)
	{
	WriteToFifo(&sReceiveFifo, data + lastCount, writeSize);
	lastCount = 0;
	}

	UARTDRV_Receive(vcom_handle, data, transferCount, UART_rx_callback);

	#ifdef ENABLE_CHIP_SHELL
	chip::NotifyShellProcess();
	#elif !defined(PW_RPC_ENABLED)
	otSysEventSignalPending();
	#endif
	}
	#endif // SLI_SI91X_MCU_INTERFACE == 0

	/**
	* @brief Read the data available from the console Uart
	*
	* @param Buf Buffer that contains the data to write
	* @param BufLength number bytes to write
	* @return int16_t Amount of bytes written or ERROR (-1)
	*/
	int16_t uartConsoleWrite(const char * Buf, uint16_t BufLength)
	{
	if (Buf == NULL \|\| BufLength < 1 \|\| BufLength > UART_TX_MAX_BUF_LEN)
	{
	return UART_CONSOLE_ERR;
	}

	if (NULL == sUartTxQueue)
	{
	// This is to prevent the first prompt from OTCLI to be rejected and to break the OTCli output
	uartConsoleInit();
	}

	#ifdef PW_RPC_ENABLED
	// Pigweed Logger is already thread safe.
	UARTDRV_ForceTransmit(vcom_handle, (uint8_t *) Buf, BufLength);
	return BufLength;
	#endif

	UartTxStruct_t workBuffer;
	memcpy(workBuffer.data, Buf, BufLength);
	workBuffer.length = BufLength;

	// this is usually a command response. Wait on queue if full.
	if (osMessageQueuePut(sUartTxQueue, &workBuffer, osPriorityNormal, osWaitForever) == osOK)
	{
	return BufLength;
	}

	return UART_CONSOLE_ERR;
	}

	/**
	* @brief Write Logs to the Uart. Appends a return character
	*
	* @param log pointer to the logs
	* @param length number of bytes to write
	* @return int16_t Amount of bytes written or ERROR (-1)
	*/
	int16_t uartLogWrite(const char * log, uint16_t length)
	{
	if (log == NULL \|\| length < 1 \|\| (length + 2) > UART_TX_MAX_BUF_LEN)
	{
	return UART_CONSOLE_ERR;
	}

	UartTxStruct_t workBuffer;
	memcpy(workBuffer.data, log, length);
	memcpy(workBuffer.data + length, "\r\n", 2);
	workBuffer.length = length + 2;

	// Don't wait when queue is full. Drop the log and return UART_CONSOLE_ERR
	if (osMessageQueuePut(sUartTxQueue, &workBuffer, osPriorityNormal, 0) == osOK)
	{
	return length;
	}

	return UART_CONSOLE_ERR;
	}

	/*
	* @brief Read the data available from the console Uart
	* @param Buffer for the data to be read, number bytes to read.
	* @return Amount of bytes that was read from the rx fifo or ERROR (-1)
	*/
	int16_t uartConsoleRead(char * Buf, uint16_t NbBytesToRead)
	{
	uint8_t * data;

	#ifdef SL_CATALOG_UARTDRV_EUSART_PRESENT
	EUSART_INT_ENABLE(SL_UARTDRV_EUSART_VCOM_PERIPHERAL, EUSART_IF_RXFL);
	#endif

	if (Buf == NULL \|\| NbBytesToRead < 1)
	{
	return UART_CONSOLE_ERR;
	}
	#if SLI_SI91X_MCU_INTERFACE == 0
	if (NbBytesToRead > AvailableDataCount(&sReceiveFifo))
	{
	UARTDRV_Count_t count, remaining;
	// Not enough data available in the fifo for the read size request
	// If there is data available in dma buffer, get it now.
	CORE_ATOMIC_SECTION(UARTDRV_GetReceiveStatus(vcom_handle, &data, &count, &remaining); if (count > lastCount) {
	WriteToFifo(&sReceiveFifo, data + lastCount, count - lastCount);
	lastCount = count;
	})
	}
	#endif // SLI_SI91X_MCU_INTERFACE == 0

	return (int16_t) RetrieveFromFifo(&sReceiveFifo, (uint8_t *) Buf, NbBytesToRead);
	}

	void uartMainLoop(void * args)
	{
	UartTxStruct_t workBuffer;

	while (1)
	{

	osStatus_t eventReceived = osMessageQueueGet(sUartTxQueue, &workBuffer, nullptr, osWaitForever);
	while (eventReceived == osOK)
	{
	uartSendBytes(workBuffer.data, workBuffer.length);
	eventReceived = osMessageQueueGet(sUartTxQueue, &workBuffer, nullptr, 0);
	}
	}
	}

	/**
	* @brief Send Bytes to UART. This blocks the UART task.
	*
	* @param buffer pointer to the buffer containing the data
	* @param nbOfBytes number of bytes to send
	*/
	void uartSendBytes(uint8_t * buffer, uint16_t nbOfBytes)
	{
	#if SLI_SI91X_MCU_INTERFACE
	// ensuring null termination of buffer
	if (nbOfBytes != CHIP_SHELL_MAX_LINE_SIZE && buffer[nbOfBytes - 1] != '\0')
	{
	buffer[nbOfBytes] = '\0';
	}
	Board_UARTPutSTR(reinterpret_cast<uint8_t *>(buffer));
	#else
	#if defined(SL_CATALOG_POWER_MANAGER_PRESENT)
	sl_power_manager_add_em_requirement(SL_POWER_MANAGER_EM1);
	#endif // SL_CATALOG_POWER_MANAGER_PRESENT

	#if SL_UARTCTRL_MUX
	sl_wfx_host_pre_uart_transfer();
	#endif // SL_UARTCTRL_MUX

	#if (defined(EFR32MG24) && defined(WF200_WIFI))
	// Blocking transmit for the MG24 + WF200 since UART TX is multiplexed with
	// WF200 SPI IRQ
	UARTDRV_ForceTransmit(vcom_handle, (uint8_t *) buffer, nbOfBytes);
	#else
	// Non Blocking Transmit
	UARTDRV_Transmit(vcom_handle, (uint8_t *) buffer, nbOfBytes, UART_tx_callback);
	osThreadFlagsWait(kUartTxCompleteFlag, osFlagsWaitAny, osWaitForever);
	#endif /* EFR32MG24 && WF200_WIFI */

	#if SL_UARTCTRL_MUX
	sl_wfx_host_post_uart_transfer();
	#endif // SL_UARTCTRL_MUX

	#if defined(SL_CATALOG_POWER_MANAGER_PRESENT)
	sl_power_manager_remove_em_requirement(SL_POWER_MANAGER_EM1);
	#endif // SL_CATALOG_POWER_MANAGER_PRESENT
	#endif // SLI_SI91X_MCU_INTERFACE
	}

	#ifdef __cplusplus
	}
	#endif