| # |
| # Copyright (c) 2023-2024 Project CHIP Authors |
| # |
| # Licensed under the Apache License, Version 2.0 (the "License"); |
| # you may not use this file except in compliance with the License. |
| # You may obtain a copy of the License at |
| # |
| # http://www.apache.org/licenses/LICENSE-2.0 |
| # |
| # Unless required by applicable law or agreed to in writing, software |
| # distributed under the License is distributed on an "AS IS" BASIS, |
| # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| # See the License for the specific language governing permissions and |
| # limitations under the License. |
| # |
| |
| rsource "../../zephyr/Kconfig" |
| |
| if CHIP |
| |
| # See config/zephyr/Kconfig for full definition |
| config CHIP_DEVICE_VENDOR_NAME |
| default "Telink Semiconductor" |
| |
| config CHIP_NFC_COMMISSIONING |
| bool "Share onboarding payload in NFC tag" |
| default n |
| imply I2C |
| imply ST25DVXXKC |
| imply NFC |
| imply NFC_NDEF |
| imply NFC_NDEF_MSG |
| imply NFC_NDEF_RECORD |
| imply NFC_NDEF_URI_REC |
| imply NFC_NDEF_URI_MSG |
| help |
| Enables sharing the onboarding payload in the NFC tag. |
| |
| # See config/zephyr/Kconfig for full definition |
| config CHIP_OTA_REQUESTOR |
| bool |
| select BOOTLOADER_MCUBOOT |
| |
| config BOOTLOADER_MCUBOOT |
| bool |
| select IMG_MANAGER |
| select STREAM_FLASH |
| select STREAM_FLASH_ERASE |
| select TELINK_W91_N22_MATTER_OTA_LAYOUT if BOARD_TLSR9118BDK40D |
| |
| config CHIP_OTA_REQUESTOR_BUFFER_SIZE |
| int "OTA Requestor image buffer size" |
| default 256 |
| depends on CHIP_OTA_REQUESTOR |
| help |
| Configures the size of the buffer used by OTA Requestor when downloading |
| and writing a new firmware image to flash. |
| |
| config CHIP_OTA_REQUESTOR_REBOOT_ON_APPLY |
| bool "Auto-reboot when firmware update is applied" |
| default y |
| depends on CHIP_OTA_REQUESTOR |
| imply REBOOT |
| help |
| Reboots the device automatically after downloading a new firmware update |
| to swap the old and the new firmware images. The reboot happens only when |
| a user consents to apply the firmware update. |
| |
| # See config/zephyr/Kconfig for full definition |
| config CHIP_OTA_IMAGE_BUILD |
| bool |
| default y if CHIP_OTA_REQUESTOR |
| |
| config SIGNED_OTA_IMAGE_FILE_NAME |
| string "Zephyr signed image file name" |
| default "zephyr.signed.lzma.signed.bin" if COMPRESS_LZMA |
| default "zephyr.signed.bin" |
| depends on CHIP_OTA_REQUESTOR |
| help |
| Provides the file name of the generated Zephyr signed image. |
| |
| config TELINK_OTA_BUTTON_TEST |
| bool "Enable image update initiation via button press" |
| default n |
| depends on CHIP_OTA_REQUESTOR |
| help |
| Merge the signed binary with the same version as the main into slot-1 of merged.hex. |
| Pressing the button initiates a forced image update. |
| |
| config TELINK_OTA_PARTITION_ADDR |
| hex "image-1 partition address" |
| default $(dt_node_reg_addr_hex,$(dt_nodelabel_path,slot1_partition),0) |
| depends on TELINK_OTA_BUTTON_TEST |
| |
| config CHIP_ROTATING_DEVICE_ID |
| bool "Generate rotating device ID" |
| default y |
| help |
| Enables the rotating device identifier that provides a non-trackable |
| identifier. The identifier is unique per device and rotates at pre-defined |
| moments. |
| |
| config CHIP_EXAMPLE_DEVICE_INFO_PROVIDER |
| bool "Include default device information provider build" |
| default y |
| |
| config CHIP_FACTORY_DATA |
| bool "Enable Factory Data support" |
| select ZCBOR |
| help |
| Enables support for reading factory data from flash memory partition. |
| It requires factory_data partition to exist. |
| |
| config CHIP_FACTORY_DATA_CUSTOM_BACKEND |
| bool "Enable Factory Data custom backend" |
| depends on !CHIP_FACTORY_DATA |
| help |
| Enables user custom factory data implementation. It cannot be used |
| with the CHIP_FACTORY_DATA that enabled default Telink factory data |
| implementation. |
| |
| config CHIP_FACTORY_DATA_BUILD |
| bool "Enable Factory Data build" |
| default n |
| help |
| Enables generation of factory data during the building. |
| It requires factory_data partition to exist. |
| As a result a new output file factory_data.bin will be created. |
| |
| config CHIP_FACTORY_DATA_VERSION |
| int |
| default 1 |
| help |
| The Factory data version contains a current version of a factory data |
| parameter set that the user cannot change. |
| After moving to the next version of the factory data set, change the default value. |
| This config is used to validate the version of a factory data set on a device-side |
| with the version of factory data saved in the Flash memory. |
| |
| if CHIP_FACTORY_DATA_BUILD |
| |
| # Factory data definitions |
| config CHIP_FACTORY_DATA_MERGE_WITH_FIRMWARE |
| bool "Enable merging generated factory data with the build target .bin file" |
| default y |
| help |
| Enables merging generated factory data with the build target zephyr.bin file. |
| As a result, output file merged.bin will consist of all partitions including |
| factory data. |
| |
| config TELINK_FACTORY_DATA_PARTITION_ADDR |
| hex "factory-data partition address" |
| default $(dt_node_reg_addr_hex,$(dt_nodelabel_path,factory_partition),0) |
| depends on CHIP_FACTORY_DATA_MERGE_WITH_FIRMWARE |
| |
| # Use default certificates without generating or providing them |
| config CHIP_FACTORY_DATA_USE_DEFAULT_CERTS |
| bool "Use default certificates located in Matter repository" |
| default y |
| help |
| Pre-generated certificates can be used for development purpose. |
| This config includes default pre-generated certificates |
| which are located in credentials/development/attestation/ directory |
| instead of generating new ones. |
| If this config is set to `n` new certificates will be generated. |
| |
| # Configs for SPAKE2 generation |
| config CHIP_FACTORY_DATA_GENERATE_SPAKE2_VERIFIER |
| bool "Enable spake2 verifier generation" |
| help |
| Enables generation of spake2 verifier according to |
| given iteration counter, salt and passcode. |
| To generate Spake2 verifier a spake2p executable must be available |
| from system variables environment. |
| |
| config CHIP_DEVICE_GENERATE_ROTATING_DEVICE_UID |
| bool "Enable generation of a new Rotating device id unique id" |
| default y |
| help |
| Enables generation of a new Rotating device id unique id. |
| |
| endif #CHIP_FACTORY_DATA_BUILD |
| |
| # See config/zephyr/Kconfig for full definition |
| config CHIP_FACTORY_RESET_ERASE_NVS |
| bool |
| default n |
| |
| endif |
| |
| config CHIP_LOG_SIZE_OPTIMIZATION |
| bool "Disable some detailed logs to decrease flash usage" |
| help |
| Disables some log levels for specific Matter log modules that provide |
| information that is too detailed to be used in most cases. You can find |
| full configuration enabled by this option in the |
| platform/telink/CHIPPlatformConfig.h file. |
| |
| config CHIP_IPV4 |
| bool "IPv4 support for Matter" |
| default n |
| depends on NET_IPV4 |
| help |
| If disabled, it allows to build Telink SDK application |
| with IPv4 support independently of the Matter stack still |
| running over IPv6. |
| |
| config CHIP_BUTTON_MANAGER_IRQ_MODE |
| bool "Use GPIO in an IRQ mode instead of polling the GPIO" |
| default y if BOARD_TLSR9118BDK40D |
| default PM |
| help |
| Use GPIO in an IRQ mode to avoid button polling loop and extend the battery lifetime by waking up by GPIO event. |
| GPIO events are working only with GPIO IRQ. This option changes button matrix configuration. |
| |
| config CHIP_ENABLE_APPLICATION_STATUS_LED |
| bool "Enable application status LED" |
| default !(PM) |
| help |
| Enable application status LED. |
| |
| config CHIP_ENABLE_PM_DURING_BLE |
| bool "Enable PM during BLE operation" |
| default PM |
| help |
| Enable PM during BLE operation. |
| |
| config CHIP_OPENTHREAD_TX_POWER |
| int "OpenThread Transmission power" |
| range -30 9 |
| default 0 |
| help |
| OpenThread Transmission power in dBm. |
| |
| config SHELL_BACKEND_SERIAL_RX_RING_BUFFER_SIZE |
| int |
| default 255 if SHELL_BACKEND_SERIAL |
| |
| config CHIP_ENABLE_POWER_ON_FACTORY_RESET |
| bool "Enable power on factory reset sequence" |
| default n |
| help |
| Enable power on factory reset sequence. If device power triggered off during |
| first 5 seconds after power on and this sequence repeated 5 times - factory |
| reset will be involved. |
| |
| config CHIP_TASK_STACK_SIZE |
| int |
| default 6192 if SOC_RISCV_TELINK_TL321X |
| default 5352 if PM |
| default 8192 |
| |
| config CHIP_USE_MARS_SENSOR |
| bool "Use Mars board sensor" |
| depends on SOC_SERIES_RISCV_TELINK_B9X && (BOARD_TLSR9518ADK80D || BOARD_TLSR9518ADK80D_RETENTION) |
| default n |