| # Copyright (c) 2021 Project CHIP Authors |
| # |
| # Licensed under the Apache License, Version 2.0 (the "License"); |
| # you may not use this file except in compliance with the License. |
| # You may obtain a copy of the License at |
| # |
| # http://www.apache.org/licenses/LICENSE-2.0 |
| # |
| # Unless required by applicable law or agreed to in writing, software |
| # distributed under the License is distributed on an "AS IS" BASIS, |
| # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| # See the License for the specific language governing permissions and |
| # limitations under the License. |
| # Auto-generated scripts for harness use only, please review before automation. The endpoints and cluster names are currently set to default |
| |
| name: |
| 4.1.1. [TC-CADMIN-1.1] Administrator Behavior using ECM [DUT - Commissioner] |
| |
| PICS: |
| - CADMIN.C |
| - CADMIN.C.C00.Tx |
| |
| config: |
| nodeId: 0x12344321 |
| cluster: "Basic" |
| endpoint: 0 |
| |
| tests: |
| - label: "Note" |
| verification: | |
| For DUT as comissioner test cases, Chip-tool command used below are an example to verify the functionality. For certification test, we expect DUT should have a capability or way to run the equivalent command. |
| disabled: true |
| |
| - label: "Precondition" |
| verification: | |
| Reset Devices to factory defaults |
| disabled: true |
| |
| - label: "TH_CR1 starts a commissioning process with TH_CE" |
| PICS: CADMIN.C |
| verification: | |
| "1. Provision the device using 1st controller chip-tool on the raspi (use above instructions) |
| " |
| disabled: true |
| |
| - label: |
| "TH_CR1 sends command to TH_CE to open a commissioning window with a |
| commissioning timeout of PIXIT.CADMIN.CwDuration seconds using ECM |
| (Enhanced Commissioning Method)." |
| PICS: CADMIN.C.C00.Tx |
| verification: | |
| On 1st controller using chip tool, open commissioning window using ECM |
| |
| ./chip-tool pairing open-commissioning-window 1 1 400 2000 3841 |
| |
| On TH1(chip-tool) Log |
| |
| CHIP:IN: Sending encrypted msg 0xaaaad3464d10 with MessageCounter:0 to 0x0000000000000001 at monotonic time: 5805157 msec |
| [1635691999.946536][3822:3827] CHIP:DMG: ICR moving to [CommandSen] |
| [1635691999.946586][3822:3827] CHIP:CTL: Manual pairing code: [35407541839] |
| [1635691999.946650][3822:3827] CHIP:CTL: SetupQRCode: [MT:00000CQM00G6V851H10] |
| [1635691999.946802][3822:3827] CHIP:EM: Sending Standalone Ack for MessageCounter:3234931243 on exchange 35324i |
| [1635691999.946850][3822:3827] CHIP:IN: Prepared plaintext message 0xffffaa58a960 to 0x0000000000000000 of type 0x10 and protocolId (0, 0) on exchange 35324i with MessageCounter:1726016118. |
| [1635691999.946895][3822:3827] CHIP:IN: Sending plaintext msg 0xffffaa58a960 with MessageCounter:1726016118 to 0x0000000000000000 at monotonic time: 5805158 msec |
| [1635691999.946983][3822:3827] CHIP:EM: Flushed pending ack for MessageCounter:3234931243 on exchange 35324i |
| |
| On DUT as server side |
| |
| CHIP minimal mDNS started advertising. |
| [1635687658.683388][3792:3792] CHIP:DIS: Failed to find a valid admin pairing. Node ID unknown |
| [1635687658.683427][3792:3792] CHIP:DIS: Start dns-sd server - no current nodeId |
| [1635687658.683456][3792:3792] CHIP:DL: MAC is not known, using a default. |
| [1635687658.683522][3792:3792] CHIP:DIS: Advertise commission parameter vendorID=9050 productID=65279 discriminator=3840/00 |
| [1635687658.683597][3792:3792] CHIP:DIS: CHIP minimal mDNS configured as "Commissionable node device". |
| [1635687658.684345][3792:3792] CHIP:DIS: Broadcasting mDns reply for query from 192.168.0.225 |
| [1635687658.687201][3792:3792] CHIP:DIS: Broadcasting mDns reply for query from 192.168.0.225 |
| disabled: true |
| |
| - label: "TH_CR1 sends command to TH_CE to read the list of Fabrics" |
| PICS: OPCREDS.C.A0001 |
| verification: | |
| On 1st controller using chip tool read fabricList |
| |
| ./chip-tool operationalcredentials read fabrics 1 0 --fabric-filtered 0 |
| |
| |
| CHIP:TOO: Endpoint: 0 Cluster: 0x0000_003E Attribute 0x0000_0001 DataVersion: 3621507058 |
| [1649245801.244173][10091:10096] CHIP:TOO: Fabrics: 1 entries |
| [1649245801.244305][10091:10096] CHIP:TOO: [1]: { |
| [1649245801.244348][10091:10096] CHIP:TOO: RootPublicKey: 045541017FCEFD0D83963C9ED7F21380C6B789EB989B5D20DC318FAE92D60D0F685666505E9C4F86C49ADC71AB3A8B9B44FD43214CF9BE2B6D47DE01F28FE1544F |
| [1649245801.244400][10091:10096] CHIP:TOO: VendorId: 65521 |
| [1649245801.244431][10091:10096] CHIP:TOO: FabricId: 1 |
| [1649245801.244461][10091:10096] CHIP:TOO: NodeId: 1 |
| [1649245801.244491][10091:10096] CHIP:TOO: Label: |
| [1649245801.244521][10091:10096] CHIP:TOO: FabricIndex: 1 |
| [1649245801.244552][10091:10096] CHIP:TOO: } |
| [1649245801.244671][10091:10096] CHIP:EM: Sending Standalone Ack for MessageCounter:8407998 on exchange 12989i |
| disabled: true |
| |
| - label: "DUT_CR2 starts a commissioning process with TH_CE" |
| PICS: CADMIN.C |
| verification: | |
| On 2nd controller, using chip-tool connect using manual code. |
| |
| On Raspi platform use commissioner-name parameter to commission different TH as server with DUT as commissioner, Pls use equivalent command on the respective TH as server |
| Below is the example when using chip tool as controller (considering 35998938564 as the manual code generated by 1st controller) |
| ./chip-tool pairing code 2 35998938564 --commissioner-name beta |
| |
| Verify whether you got below message in the log of TH |
| |
| Device commissioning completed with success |
| disabled: true |
| |
| - label: "Verify TH_CE is now discoverable over DNS-SD with two SRV Records" |
| verification: | |
| On the raspi , Verify if the DUT is broadcasting using |
| |
| ubuntu@ubuntu:~/may10_cntrl2/connectedhomeip/examples/chip-tool/out/debug$ avahi-browse -rt _matter._tcp |
| + eth0 IPv6 E0AF53B23E580769-0000000000000002 _matter._tcp local |
| + eth0 IPv6 7FF84D214A19B581-0000000000000001 _matter._tcp local |
| = eth0 IPv6 E0AF53B23E580769-0000000000000002 _matter._tcp local |
| hostname = [E45F010F3BAF0000.local] |
| address = [fe80::e65f:1ff:fe0f:3baf] |
| port = [5540] |
| txt = ["T=1" "CRA=300" "CRI=5000"] |
| = eth0 IPv6 7FF84D214A19B581-0000000000000001 _matter._tcp local |
| hostname = [E45F010F3BAF0000.local] |
| address = [fe80::e65f:1ff:fe0f:3baf] |
| port = [5540] |
| txt = ["T=1" "CRA=300" "CRI=5000"] |
| disabled: true |
| |
| - label: |
| "DUT_CR2 sends command to TH_CE to write and read the Basic |
| Information Clusters NodeLabel mandatory attribute" |
| PICS: BINFO.C.A0005 |
| verification: | |
| On 2nd controller using chip tool write and read node-label |
| |
| On Raspi platform use commissioner-name parameter to commission different TH as server with DUT as commissioner, Pls use equivalent command on the respective TH as server |
| Below is the example when using chip tool as controller |
| ./chip-tool basic write node-label te5new 2 0 --commissioner-name beta |
| |
| CHIP:DMG: WriteClient moving to [ResponseRe] |
| [1649671460.431199][20958:20963] CHIP:DMG: WriteResponseMessage = |
| [1649671460.431217][20958:20963] CHIP:DMG: { |
| [1649671460.431230][20958:20963] CHIP:DMG: AttributeStatusIBs = |
| [1649671460.431252][20958:20963] CHIP:DMG: [ |
| [1649671460.431266][20958:20963] CHIP:DMG: AttributeStatusIB = |
| [1649671460.431282][20958:20963] CHIP:DMG: { |
| [1649671460.431297][20958:20963] CHIP:DMG: AttributePathIB = |
| [1649671460.431314][20958:20963] CHIP:DMG: { |
| [1649671460.431331][20958:20963] CHIP:DMG: Endpoint = 0x0, |
| [1649671460.431347][20958:20963] CHIP:DMG: Cluster = 0x28, |
| [1649671460.431364][20958:20963] CHIP:DMG: Attribute = 0x0000_0005, |
| [1649671460.431380][20958:20963] CHIP:DMG: } |
| [1649671460.431403][20958:20963] CHIP:DMG: |
| [1649671460.431422][20958:20963] CHIP:DMG: StatusIB = |
| [1649671460.431445][20958:20963] CHIP:DMG: { |
| [1649671460.431467][20958:20963] CHIP:DMG: status = 0x00 (SUCCESS), |
| [1649671460.431488][20958:20963] CHIP:DMG: }, |
| [1649671460.431511][20958:20963] CHIP:DMG: |
| [1649671460.431530][20958:20963] CHIP:DMG: }, |
| [1649671460.431556][20958:20963] CHIP:DMG: |
| [1649671460.431570][20958:20963] CHIP:DMG: ], |
| [1649671460.431593][20958:20963] CHIP:DMG: |
| [1649671460.431607][20958:20963] CHIP:DMG: InteractionModelRevision = 1 |
| [1649671460.431620][20958:20963] CHIP:DMG: } |
| [1649671460.431685][20958:20963] CHIP:DMG: WriteClient moving to [AwaitingDe] |
| [1649671460.431729][20958:20963] CHIP:EM: Sending Standalone Ack for MessageCounter:11088724 on exchange 41848i |
| |
| |
| |
| Verify read attribute returns the updated value written |
| |
| On Raspi platform use commissioner-name parameter to commission different TH as server with DUT as commissioner, Pls use equivalent command on the respective TH as server |
| ./chip-tool basic read node-label 2 0 --commissioner-name beta |
| |
| CHIP:DMG: ReportDataMessage = |
| [1649671466.310233][20969:20974] CHIP:DMG: { |
| [1649671466.310241][20969:20974] CHIP:DMG: AttributeReportIBs = |
| [1649671466.310256][20969:20974] CHIP:DMG: [ |
| [1649671466.310265][20969:20974] CHIP:DMG: AttributeReportIB = |
| [1649671466.310281][20969:20974] CHIP:DMG: { |
| [1649671466.310292][20969:20974] CHIP:DMG: AttributeDataIB = |
| [1649671466.310304][20969:20974] CHIP:DMG: { |
| [1649671466.310317][20969:20974] CHIP:DMG: DataVersion = 0xd581a5e8, |
| [1649671466.310328][20969:20974] CHIP:DMG: AttributePathIB = |
| [1649671466.310342][20969:20974] CHIP:DMG: { |
| [1649671466.310355][20969:20974] CHIP:DMG: Endpoint = 0x0, |
| [1649671466.310367][20969:20974] CHIP:DMG: Cluster = 0x28, |
| [1649671466.310380][20969:20974] CHIP:DMG: Attribute = 0x0000_0005, |
| [1649671466.310391][20969:20974] CHIP:DMG: } |
| [1649671466.310405][20969:20974] CHIP:DMG: |
| [1649671466.310420][20969:20974] CHIP:DMG: Data = "te8", |
| [1649671466.310432][20969:20974] CHIP:DMG: }, |
| [1649671466.310446][20969:20974] CHIP:DMG: |
| [1649671466.310457][20969:20974] CHIP:DMG: }, |
| [1649671466.310471][20969:20974] CHIP:DMG: |
| [1649671466.310481][20969:20974] CHIP:DMG: ], |
| [1649671466.310497][20969:20974] CHIP:DMG: |
| [1649671466.310508][20969:20974] CHIP:DMG: SuppressResponse = true, |
| [1649671466.310518][20969:20974] CHIP:DMG: InteractionModelRevision = 1 |
| [1649671466.310528][20969:20974] CHIP:DMG: } |
| [1649671466.310629][20969:20974] CHIP:TOO: Endpoint: 0 Cluster: 0x0000_0028 Attribute 0x0000_0005 DataVersion: 3582043624 |
| [1649671466.310646][20969:20974] CHIP:TOO: NodeLabel: te8 |
| [1649671466.310704][20969:20974] CHIP:EM: Sending Standalone Ack for MessageCounter:15357338 on exchange 20724i |
| disabled: true |
| |
| - label: "DUT_CR2 sends command to TH_CE to read the list of Fabrics" |
| PICS: OPCREDS.C.A0001 |
| verification: | |
| On 2nd controller using chip tool read fabricList |
| |
| |
| Below is the example using chip tool as controller |
| |
| ./chip-tool operationalcredentials read fabrics 2 0 --fabric-filtered 0 --commissioner-name beta |
| |
| |
| |
| CHIP:TOO: Endpoint: 0 Cluster: 0x0000_003E Attribute 0x0000_0001 DataVersion: 3621507063 |
| [1649245825.315152][10098:10103] CHIP:TOO: Fabrics: 2 entries |
| [1649245825.315316][10098:10103] CHIP:TOO: [1]: { |
| [1649245825.315370][10098:10103] CHIP:TOO: RootPublicKey: 045541017FCEFD0D83963C9ED7F21380C6B789EB989B5D20DC318FAE92D60D0F685666505E9C4F86C49ADC71AB3A8B9B44FD43214CF9BE2B6D47DE01F28FE1544F |
| [1649245825.315436][10098:10103] CHIP:TOO: VendorId: 65521 |
| [1649245825.315479][10098:10103] CHIP:TOO: FabricId: 1 |
| [1649245825.315518][10098:10103] CHIP:TOO: NodeId: 1 |
| [1649245825.315557][10098:10103] CHIP:TOO: Label: |
| [1649245825.315596][10098:10103] CHIP:TOO: FabricIndex: 1 |
| [1649245825.315637][10098:10103] CHIP:TOO: } |
| [1649245825.315697][10098:10103] CHIP:TOO: [2]: { |
| [1649245825.315747][10098:10103] CHIP:TOO: RootPublicKey: 047D75BF7D91FCFFB29DAD375D09790FEBE9205227C44D4FF8EB70ADAD02E416E08269B9F77E86FE14270525B64C41417CEA3E9FDE0552AE8DF05F8D98B6B6E2E2 |
| [1649245825.315789][10098:10103] CHIP:TOO: VendorId: 65521 |
| [1649245825.315830][10098:10103] CHIP:TOO: FabricId: 1 |
| [1649245825.315870][10098:10103] CHIP:TOO: NodeId: 2 |
| [1649245825.315908][10098:10103] CHIP:TOO: Label: |
| [1649245825.315947][10098:10103] CHIP:TOO: FabricIndex: 2 |
| [1649245825.315986][10098:10103] CHIP:TOO: } |
| disabled: true |
| |
| - label: |
| "TH_CR1 sends command to TH_CE to write and read the Basic Information |
| Clusters NodeLabel mandatory attribute" |
| PICS: BINFO.C.A0005 |
| verification: | |
| On first controller using chip tool, write attribute and read attribute |
| |
| ./chip-tool basic write node-label te8 1 0 |
| |
| CHIP:DMG: WriteResponse = |
| CHIP:DMG: WriteResponseMessage = |
| [1649245940.788522][10110:10115] CHIP:DMG: { |
| [1649245940.788577][10110:10115] CHIP:DMG: AttributeStatusIBs = |
| [1649245940.788653][10110:10115] CHIP:DMG: [ |
| [1649245940.788713][10110:10115] CHIP:DMG: AttributeStatusIB = |
| [1649245940.788787][10110:10115] CHIP:DMG: { |
| [1649245940.788852][10110:10115] CHIP:DMG: AttributePathIB = |
| [1649245940.788931][10110:10115] CHIP:DMG: { |
| [1649245940.789009][10110:10115] CHIP:DMG: Endpoint = 0x0, |
| [1649245940.789143][10110:10115] CHIP:DMG: Cluster = 0x28, |
| [1649245940.789228][10110:10115] CHIP:DMG: Attribute = 0x0000_0005, |
| [1649245940.789313][10110:10115] CHIP:DMG: } |
| [1649245940.789388][10110:10115] CHIP:DMG: |
| [1649245940.789454][10110:10115] CHIP:DMG: StatusIB = |
| [1649245940.789519][10110:10115] CHIP:DMG: { |
| [1649245940.789588][10110:10115] CHIP:DMG: status = 0x00 (SUCCESS), |
| [1649245940.789654][10110:10115] CHIP:DMG: }, |
| [1649245940.789719][10110:10115] CHIP:DMG: |
| [1649245940.789778][10110:10115] CHIP:DMG: }, |
| [1649245940.789841][10110:10115] CHIP:DMG: |
| [1649245940.789885][10110:10115] CHIP:DMG: ], |
| [1649245940.789941][10110:10115] CHIP:DMG: |
| [1649245940.789984][10110:10115] CHIP:DMG: InteractionModelRevision = 1 |
| [1649245940.790033][10110:10115] CHIP:DMG: } |
| [1649245940.790167][10110:10115] CHIP:DMG: WriteClient moving to [AwaitingDe] |
| |
| |
| Verify read attribute returns the updated value written |
| ./chip-tool basic read node-label 1 0 |
| |
| CHIP:TOO: Endpoint: 0 Cluster: 0x0000_0028 Attribute 0x0000_0005 DataVersion: 3061847068 |
| [1649245950.006849][10116:10121] CHIP:TOO: NodeLabel: te8 |
| [1649245950.007024][10116:10121] CHIP:EM: Sending Standalone Ack for MessageCounter:12495101 on exchange 24816i |
| disabled: true |
| |
| - label: |
| "DUT_CR2 sends command to TH_CE to read, write and then read the Basic |
| Information Clusters NodeLabel mandatory attribute" |
| PICS: BINFO.C.A0005 |
| verification: | |
| On 2nd controller using chip-tool read, write attribute and then read attribute to and from TH_CE |
| |
| Below is an example of using chip tool as controller |
| |
| ./chip-tool basic write node-label te5new 2 0 --commissioner-name beta |
| |
| CHIP:DMG: WriteResponseMessage = |
| [1649245940.788522][10110:10115] CHIP:DMG: { |
| [1649245940.788577][10110:10115] CHIP:DMG: AttributeStatusIBs = |
| [1649245940.788653][10110:10115] CHIP:DMG: [ |
| [1649245940.788713][10110:10115] CHIP:DMG: AttributeStatusIB = |
| [1649245940.788787][10110:10115] CHIP:DMG: { |
| [1649245940.788852][10110:10115] CHIP:DMG: AttributePathIB = |
| [1649245940.788931][10110:10115] CHIP:DMG: { |
| [1649245940.789009][10110:10115] CHIP:DMG: Endpoint = 0x0, |
| [1649245940.789143][10110:10115] CHIP:DMG: Cluster = 0x28, |
| [1649245940.789228][10110:10115] CHIP:DMG: Attribute = 0x0000_0005, |
| [1649245940.789313][10110:10115] CHIP:DMG: } |
| [1649245940.789388][10110:10115] CHIP:DMG: |
| [1649245940.789454][10110:10115] CHIP:DMG: StatusIB = |
| [1649245940.789519][10110:10115] CHIP:DMG: { |
| [1649245940.789588][10110:10115] CHIP:DMG: status = 0x00 (SUCCESS), |
| [1649245940.789654][10110:10115] CHIP:DMG: }, |
| [1649245940.789719][10110:10115] CHIP:DMG: |
| [1649245940.789778][10110:10115] CHIP:DMG: }, |
| [1649245940.789841][10110:10115] CHIP:DMG: |
| [1649245940.789885][10110:10115] CHIP:DMG: ], |
| [1649245940.789941][10110:10115] CHIP:DMG: |
| [1649245940.789984][10110:10115] CHIP:DMG: InteractionModelRevision = 1 |
| [1649245940.790033][10110:10115] CHIP:DMG: } |
| [1649245940.790167][10110:10115] CHIP:DMG: WriteClient moving to [AwaitingDe] |
| |
| Verify read attribute returns the updated value written |
| |
| ./chip-tool basic read node-label 2 0 --commissioner-name beta |
| |
| CHIP:TOO: Endpoint: 0 Cluster: 0x0000_0028 Attribute 0x0000_0005 DataVersion: 3061847068 |
| [1649245950.006849][10116:10121] CHIP:TOO: NodeLabel: te5new |
| [1649245950.007024][10116:10121] CHIP:EM: Sending Standalone Ack for MessageCounter:12495101 on exchange 24816i |
| disabled: true |
| |
| - label: "Turn off TH_CR1" |
| verification: | |
| No need to do anything as chip-tool process exits after each command |
| disabled: true |
| |
| - label: |
| "DUT_CR2 sends command to TH_CE to open a commissioning window using a |
| commissioning timeout of PIXIT.CADMIN.CwDuration seconds using ECM |
| (Enhanced Commissioning Method)" |
| PICS: CADMIN.C.C00.Tx |
| verification: | |
| On 2nd controller open commissioning window using ECM |
| |
| Below is an example when using chip tool as controller |
| ./chip-tool pairing open-commissionig-window 2 1 300 1000 3841 --commissioner-name beta |
| |
| CHIP: [IN] Prepared encrypted message 0x124012e80 to 0x0000000000000001 of type 0x8 and protocolId (0, 1) on exchange 50829i with MessageCounter:0. |
| [1635693418549] [30519:4583024] CHIP: [IN] Sending encrypted msg 0x124012e80 with MessageCounter:0 to 0x0000000000000001 at monotonic time: 5995099243 msec |
| [1635693418549] [30519:4583024] CHIP: [DMG] ICR moving to [CommandSen] |
| [1635693418549] [30519:4583024] CHIP: [CTL] Manual pairing code: [34995354639] |
| [1635693418550] [30519:4583024] CHIP: [CTL] SetupQRCode: [MT:00000CQM00YND84XX10] |
| [1635693418550] [30519:4583024] CHIP: [EM] Sending Standalone Ack for MessageCounter:3441918415 on exchange 50828i |
| [1635693418550] [30519:4583024] CHIP: [IN] Prepared plaintext message 0x16b92d198 to 0x0000000000000000 of type 0x10 and protocolId (0, 0) on exchange 50828i with MessageCounter:3727034150. |
| [1635693418550] [30519:4583024] CHIP: [IN] Sending plaintext msg 0x16b92d198 with Mes |
| disabled: true |
| |
| - label: |
| "DUT_CR2 sends command to TH_CE to revoke the commissioning window |
| using the Revoke Commissioning command" |
| PICS: CADMIN.C.C02.Tx |
| verification: | |
| On 2nd controller, run revoke command |
| |
| Below is an example when using chip tool as controller |
| |
| ./chip-tool administratorcommissioning revoke-commissioning 2 0 --timedInteractionTimeoutMs 1000 --commissioner-name beta |
| |
| |
| CHIP: [DMG] InvokeResponseMessage = |
| [1648115245106] [6681:3894448] CHIP: [DMG] { |
| [1648115245106] [6681:3894448] CHIP: [DMG] suppressResponse = false, |
| [1648115245106] [6681:3894448] CHIP: [DMG] InvokeResponseIBs = |
| [1648115245106] [6681:3894448] CHIP: [DMG] [ |
| [1648115245106] [6681:3894448] CHIP: [DMG] InvokeResponseIB = |
| [1648115245106] [6681:3894448] CHIP: [DMG] { |
| [1648115245106] [6681:3894448] CHIP: [DMG] CommandStatusIB = |
| [1648115245106] [6681:3894448] CHIP: [DMG] { |
| [1648115245106] [6681:3894448] CHIP: [DMG] CommandPathIB = |
| [1648115245106] [6681:3894448] CHIP: [DMG] { |
| [1648115245106] [6681:3894448] CHIP: [DMG] EndpointId = 0x0, |
| [1648115245106] [6681:3894448] CHIP: [DMG] ClusterId = 0x3c, |
| [1648115245106] [6681:3894448] CHIP: [DMG] CommandId = 0x2, |
| [1648115245106] [6681:3894448] CHIP: [DMG] }, |
| [1648115245106] [6681:3894448] CHIP: [DMG] |
| [1648115245106] [6681:3894448] CHIP: [DMG] StatusIB = |
| [1648115245106] [6681:3894448] CHIP: [DMG] { |
| [1648115245106] [6681:3894448] CHIP: [DMG] status = 0x0, |
| [1648115245106] [6681:3894448] CHIP: [DMG] }, |
| [1648115245106] [6681:3894448] CHIP: [DMG] |
| [1648115245106] [6681:3894448] CHIP: [DMG] }, |
| [1648115245106] [6681:3894448] CHIP: [DMG] |
| [1648115245106] [6681:3894448] CHIP: [DMG] }, |
| [1648115245106] [6681:3894448] CHIP: [DMG] |
| [1648115245106] [6681:3894448] CHIP: [DMG] ], |
| [1648115245107] [6681:3894448] CHIP: [DMG] |
| [1648115245107] [6681:3894448] CHIP: [DMG] InteractionModelRevision = 1 |
| [1648115245107] [6681:3894448] CHIP: [DMG] }, |
| [1648115245107] [6681:3894448] CHIP: [DMG] Received Command Response Status for Endpoint=0 Cluster=0x0000_003C Command=0x0000_0002 Status=0x0 |
| disabled: true |
| |
| - label: |
| "TH_CR3 attempts to execute a PASE to starts a commissioning process |
| with TH_CE" |
| PICS: CADMIN.C |
| verification: | |
| On 3rd controller using chip-tool connect using manual code generated from 1st controller. This attempt should fail, i.e |
| |
| ./chip-tool pairing code 3 34995354639 --commissioner-name gamma |
| |
| verify you got the following message in the TH log |
| |
| CHIP:SC: PASESession timed out while waiting for a response from the peer. Expected message type was 33 |
| CHIP:TOO: Secure Pairing Failed |
| CHIP:TOO: Pairing Failure: ../../third_party/connectedhomeip/src/protocols/secure_channel/PASESession.cpp:324: CHIP Error 0x00000032: Timeout |
| disabled: true |
| |
| - label: |
| "DUT_CR2 sends command to TH_CE to write and read the Basic |
| Information Clusters NodeLabel mandatory attribute" |
| PICS: BINFO.C.A0005 |
| verification: | |
| On 2nd controller , write attribute and read attribute to and from TH_CE |
| |
| Below is the example using chip tool as controller |
| |
| ./chip-tool basic write node-label te5new 2 0 --commissioner-name beta |
| |
| CHIP:DMG: WriteResponseMessage = |
| [1649245940.788522][10110:10115] CHIP:DMG: { |
| [1649245940.788577][10110:10115] CHIP:DMG: AttributeStatusIBs = |
| [1649245940.788653][10110:10115] CHIP:DMG: [ |
| [1649245940.788713][10110:10115] CHIP:DMG: AttributeStatusIB = |
| [1649245940.788787][10110:10115] CHIP:DMG: { |
| [1649245940.788852][10110:10115] CHIP:DMG: AttributePathIB = |
| [1649245940.788931][10110:10115] CHIP:DMG: { |
| [1649245940.789009][10110:10115] CHIP:DMG: Endpoint = 0x0, |
| [1649245940.789143][10110:10115] CHIP:DMG: Cluster = 0x28, |
| [1649245940.789228][10110:10115] CHIP:DMG: Attribute = 0x0000_0005, |
| [1649245940.789313][10110:10115] CHIP:DMG: } |
| [1649245940.789388][10110:10115] CHIP:DMG: |
| [1649245940.789454][10110:10115] CHIP:DMG: StatusIB = |
| [1649245940.789519][10110:10115] CHIP:DMG: { |
| [1649245940.789588][10110:10115] CHIP:DMG: status = 0x00 (SUCCESS), |
| [1649245940.789654][10110:10115] CHIP:DMG: }, |
| [1649245940.789719][10110:10115] CHIP:DMG: |
| [1649245940.789778][10110:10115] CHIP:DMG: }, |
| [1649245940.789841][10110:10115] CHIP:DMG: |
| [1649245940.789885][10110:10115] CHIP:DMG: ], |
| [1649245940.789941][10110:10115] CHIP:DMG: |
| [1649245940.789984][10110:10115] CHIP:DMG: InteractionModelRevision = 1 |
| [1649245940.790033][10110:10115] CHIP:DMG: } |
| [1649245940.790167][10110:10115] CHIP:DMG: WriteClient moving to [AwaitingDe] |
| |
| Verify read attribute returns the updated value written |
| |
| ./chip-tool basic read node-label 2 0 --commissioner-name beta |
| |
| |
| CHIP:TOO: Endpoint: 0 Cluster: 0x0000_0028 Attribute 0x0000_0005 DataVersion: 3061847068 |
| [1649245950.006849][10116:10121] CHIP:TOO: NodeLabel: te5new |
| [1649245950.007024][10116:10121] CHIP:EM: Sending Standalone Ack for MessageCounter:12495101 on exchange 24816i |
| disabled: true |
| |
| - label: |
| "DUT_CR2 sends command to TH_CE to open a commissioning window using |
| ECM" |
| PICS: CADMIN.C.C00.Tx |
| verification: | |
| On 2nd controller open commissioning window using ECM |
| |
| Below is an example when using chip tool as controller |
| ./chip-tool pairing open-commissioning-window 2 1 180 1000 3840 --commissioner-name beta |
| |
| CHIP: [IN] Prepared encrypted message 0x124012e80 to 0x0000000000000001 of type 0x8 and protocolId (0, 1) on exchange 50829i with MessageCounter:0. |
| [1635693418549] [30519:4583024] CHIP: [IN] Sending encrypted msg 0x124012e80 with MessageCounter:0 to 0x0000000000000001 at monotonic time: 5995099243 msec |
| [1635693418549] [30519:4583024] CHIP: [DMG] ICR moving to [CommandSen] |
| [1635693418549] [30519:4583024] CHIP: [CTL] Manual pairing code: [34995354639] |
| [1635693418550] [30519:4583024] CHIP: [CTL] SetupQRCode: [MT:00000CQM00YND84XX10] |
| [1635693418550] [30519:4583024] CHIP: [EM] Sending Standalone Ack for MessageCounter:3441918415 on exchange 50828i |
| [1635693418550] [30519:4583024] CHIP: [IN] Prepared plaintext message 0x16b92d198 to 0x0000000000000000 of type 0x10 and protocolId (0, 0) on exchange 50828i with MessageCounter:3727034150. |
| [1635693418550] [30519:4583024] CHIP: [IN] Sending plaintext msg 0x16b92d198 with Mes |
| disabled: true |
| |
| - label: |
| "Wait for commissioning window that was opened in step 13 to timeout" |
| verification: | |
| Wait for the timeout of commissioning window in the above step |
| disabled: true |
| |
| - label: |
| "DUT_CR2 sends command to TH_CE to open a commissioning window using |
| ECM" |
| PICS: CADMIN.C.C00.Tx |
| verification: | |
| On 2nd controller open commissioning window using ECM |
| |
| Below is an example when using chip tool as controller |
| ./chip-tool pairing open-commissionig-window 2 1 300 1000 3840 --commissioner-name beta |
| |
| CHIP: [IN] Prepared encrypted message 0x124012e80 to 0x0000000000000001 of type 0x8 and protocolId (0, 1) on exchange 50829i with MessageCounter:0. |
| [1635693418549] [30519:4583024] CHIP: [IN] Sending encrypted msg 0x124012e80 with MessageCounter:0 to 0x0000000000000001 at monotonic time: 5995099243 msec |
| [1635693418549] [30519:4583024] CHIP: [DMG] ICR moving to [CommandSen] |
| [1635693418549] [30519:4583024] CHIP: [CTL] Manual pairing code: [34995354639] |
| [1635693418550] [30519:4583024] CHIP: [CTL] SetupQRCode: [MT:00000CQM00YND84XX10] |
| [1635693418550] [30519:4583024] CHIP: [EM] Sending Standalone Ack for MessageCounter:3441918415 on exchange 50828i |
| [1635693418550] [30519:4583024] CHIP: [IN] Prepared plaintext message 0x16b92d198 to 0x0000000000000000 of type 0x10 and protocolId (0, 0) on exchange 50828i with MessageCounter:3727034150. |
| [1635693418550] [30519:4583024] CHIP: [IN] Sending plaintext msg 0x16b92d198 with Mes |
| disabled: true |
| |
| - label: |
| "TH_CR1 starts a commissioning process with TH_CE before the timeout |
| from step 15" |
| PICS: CADMIN.C |
| verification: | |
| On 1st controller, using chip-tool connect using manual code. |
| |
| Below is the example when using chip tool as controller (considering 34995354639 as the manual code generated by DUT) |
| ./chip-tool pairing code 2 34995354639 |
| |
| [1651786200275] [36301:315544] CHIP: [DMG] Received Command Response Data, Endpoint=0 Cluster=0x0000_003E Command=0x0000_0008 |
| [1651786200275] [36301:315544] CHIP: [CTL] Device returned status 9 on receiving the NOC |
| [1651786200275] [36301:315544] CHIP: [CTL] Add NOC failed with error ../../src/controller/CHIPDeviceController.cpp:1187: CHIP Error 0x0000007E: Trying to add a NOC for a fabric that already exists |
| [1651786200275] [36301:315544] CHIP: [CTL] Error on commissioning step "SendNOC": "../../src/controller/CHIPDeviceController.cpp:1187: CHIP Error 0x0000007E: Trying to add a NOC for a fabric that already exists" |
| |
| Verify that the commissioning process fails as TH_CE was already commissioned by TH_CR1 in step 1 |
| disabled: true |
