| /* |
| * |
| * Copyright (c) 2022 Project CHIP Authors |
| * |
| * Licensed under the Apache License, Version 2.0 (the "License"); |
| * you may not use this file except in compliance with the License. |
| * You may obtain a copy of the License at |
| * |
| * http://www.apache.org/licenses/LICENSE-2.0 |
| * |
| * Unless required by applicable law or agreed to in writing, software |
| * distributed under the License is distributed on an "AS IS" BASIS, |
| * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| * See the License for the specific language governing permissions and |
| * limitations under the License. |
| */ |
| |
| #ifndef RSI_CONFIG_H |
| #define RSI_CONFIG_H |
| |
| #include "rsi_wlan_defines.h" |
| |
| //! Enable feature |
| #define RSI_ENABLE 1 |
| //! Disable feature |
| #define RSI_DISABLE 0 |
| |
| //! To enable wlan opermode |
| #define RSI_OPERMODE_WLAN 0 |
| |
| //! To enable concurrent mode |
| #define CONCURRENT_MODE RSI_DISABLE |
| |
| //! opermode command paramaters |
| /*=======================================================================*/ |
| //! To set wlan feature select bit map |
| #define RSI_FEATURE_BIT_MAP (FEAT_SECURITY_OPEN) |
| |
| //! TCP IP BYPASS feature check |
| #ifdef RS911X_SOCKETS |
| #define RSI_TCP_IP_BYPASS RSI_DISABLE |
| |
| #define RSI_TCP_IP_FEATURE_BIT_MAP \ |
| (TCP_IP_FEAT_DHCPV4_CLIENT | /*TCP_IP_FEAT_HTTP_CLIENT | */ \ |
| TCP_IP_FEAT_EXTENSION_VALID | /*TCP_IP_FEAT_SSL |*/ /*TCP_IP_FEAT_DNS_CLIENT |*/ \ |
| 0) |
| //! To set custom feature select bit map |
| #define RSI_CUSTOM_FEATURE_BIT_MAP FEAT_CUSTOM_FEAT_EXTENTION_VALID |
| |
| #else /* Don't use RSI_SOCKETS */ |
| #define RSI_TCP_IP_BYPASS RSI_ENABLE |
| #define RSI_TCP_IP_FEATURE_BIT_MAP (TCP_IP_FEAT_BYPASS /*| TCP_IP_FEAT_EXTENSION_VALID*/) |
| #endif |
| |
| //! To set Extended custom feature select bit map |
| #if WIFI_ENABLE_SECURITY_WPA3 |
| #ifdef RSI_M4_INTERFACE |
| #define RSI_EXT_CUSTOM_FEATURE_BIT_MAP (EXT_FEAT_256K_MODE | EXT_FEAT_IEEE_80211W) |
| #else |
| #define RSI_EXT_CUSTOM_FEATURE_BIT_MAP (EXT_FEAT_384K_MODE | EXT_FEAT_IEEE_80211W) |
| #endif |
| #else |
| #ifdef RSI_M4_INTERFACE |
| #define RSI_EXT_CUSTOM_FEATURE_BIT_MAP EXT_FEAT_256K_MODE |
| #else |
| #define RSI_EXT_CUSTOM_FEATURE_BIT_MAP EXT_FEAT_384K_MODE |
| #endif |
| #endif |
| |
| //! To set Extended TCPIP feature select bit map |
| #define RSI_EXT_TCPIP_FEATURE_BITMAP (/*EXT_FEAT_HTTP_OTAF_SUPPORT |*/ EXT_TCP_IP_SSL_16K_RECORD) |
| //! Extended custom feature is selected internally |
| //! CCP -- EXT_FEAT_256K_MODE |
| //! Wiseconnect -- EXT_FEAT_384K_MODE |
| /*=======================================================================*/ |
| //! Feature frame parameters |
| /*=======================================================================*/ |
| #define PLL_MODE 0 |
| #define RF_TYPE 1 //! 0 - External RF 1- Internal RF |
| #define WIRELESS_MODE 0 |
| #define ENABLE_PPP 0 |
| #define AFE_TYPE 1 |
| #define FEATURE_ENABLES 0 |
| /*=======================================================================*/ |
| //! Band command paramters |
| /*=======================================================================*/ |
| |
| //! RSI_BAND_2P4GHZ(2.4GHz) or RSI_BAND_5GHZ(5GHz) or RSI_DUAL_BAND |
| #define RSI_BAND RSI_BAND_2P4GHZ |
| /*=======================================================================*/ |
| //! set region command paramters |
| /*=======================================================================*/ |
| |
| //! RSI_ENABLE or RSI_DISABLE Set region support |
| #define RSI_SET_REGION_SUPPORT RSI_DISABLE //@ RSI_ENABLE or RSI_DISABLE set region |
| |
| //! If 1:region configurations taken from user ;0:region configurations taken from beacon |
| #define RSI_SET_REGION_FROM_USER_OR_BEACON 1 |
| |
| //! 0-Default Region domain ,1-US, 2-EUROPE, 3-JAPAN |
| #define RSI_REGION_CODE 1 |
| |
| //! 0- Without On Board Antenna , 1- With On Board Antenna |
| #define RSI_MODULE_TYPE 1 |
| |
| /*=======================================================================*/ |
| //! set region AP command paramters |
| /*=======================================================================*/ |
| |
| //! RSI_ENABLE or RSI_DISABLE Set region AP support |
| #define RSI_SET_REGION_AP_SUPPORT RSI_DISABLE |
| |
| //! If 1:region configurations taken from user ;0:region configurations taken from firmware |
| #define RSI_SET_REGION_AP_FROM_USER RSI_DISABLE |
| |
| //! "US" or "EU" or "JP" or other region codes |
| #define RSI_COUNTRY_CODE "US" |
| /*=======================================================================*/ |
| |
| //! Rejoin parameters |
| /*=======================================================================*/ |
| |
| //! RSI_ENABLE or RSI_DISABLE rejoin params |
| #define RSI_REJOIN_PARAMS_SUPPORT RSI_ENABLE |
| |
| //! Rejoin retry count. If 0 retries infinity times |
| #define RSI_REJOIN_MAX_RETRY 5 |
| |
| //! Periodicity of rejoin attempt |
| #define RSI_REJOIN_SCAN_INTERVAL 1 |
| |
| //! Beacon missed count |
| #define RSI_REJOIN_BEACON_MISSED_COUNT 40 |
| |
| //! RSI_ENABLE or RSI_DISABLE retry for first time join failure |
| #define RSI_REJOIN_FIRST_TIME_RETRY RSI_DISABLE |
| |
| /*=======================================================================*/ |
| |
| //! BG scan command parameters |
| /*=======================================================================*/ |
| |
| //! RSI_ENABLE or RSI_DISABLE BG Scan support |
| #define RSI_BG_SCAN_SUPPORT RSI_ENABLE |
| |
| //! RSI_ENABLE or RSI_DISABLE BG scan |
| #define RSI_BG_SCAN_ENABLE RSI_ENABLE |
| |
| //! RSI_ENABLE or RSI_DISABLE instant BG scan |
| #define RSI_INSTANT_BG RSI_ENABLE |
| |
| //! BG scan threshold value |
| #define RSI_BG_SCAN_THRESHOLD 63 |
| |
| //! RSSI tolerance Threshold |
| #define RSI_RSSI_TOLERANCE_THRESHOLD 4 |
| |
| //! BG scan periodicity |
| #define RSI_BG_SCAN_PERIODICITY 2 |
| |
| //! Active scan duration |
| #define RSI_ACTIVE_SCAN_DURATION 50 |
| |
| //! Passive scan duration |
| #define RSI_PASSIVE_SCAN_DURATION 50 |
| |
| //! Multi probe |
| #define RSI_MULTIPROBE RSI_ENABLE |
| |
| /*=======================================================================*/ |
| |
| //! RSI_ENABLE or RSI_DISABLE to set RTS threshold config |
| #define RSI_WLAN_CONFIG_ENABLE RSI_ENABLE |
| |
| #define CONFIG_RTSTHRESHOLD 1 |
| |
| #define RSI_RTS_THRESHOLD 2346 |
| |
| /*=======================================================================*/ |
| |
| //! Roaming parameters |
| /*=======================================================================*/ |
| |
| //! RSI_ENABLE or RSI_DISABLE Roaming support |
| #define RSI_ROAMING_SUPPORT RSI_DISABLE |
| |
| //! roaming threshold value |
| #define RSI_ROAMING_THRESHOLD 67 |
| |
| //! roaming hysterisis value |
| #define RSI_ROAMING_HYSTERISIS 4 |
| |
| /*=======================================================================*/ |
| //! High Throughput Capabilies related information |
| /*=======================================================================*/ |
| |
| //! RSI_ENABLE or RSI_DISABLE 11n mode in AP mode |
| #define RSI_MODE_11N_ENABLE RSI_DISABLE |
| |
| //! HT caps supported |
| #define RSI_HT_CAPS_NUM_RX_STBC (1 << 8) |
| #define RSI_HT_CAPS_SHORT_GI_20MHZ BIT(5) |
| #define RSI_HT_CAPS_GREENFIELD_EN BIT(4) |
| #define RSI_HT_CAPS_SUPPORT_CH_WIDTH BIT(1) |
| |
| //! HT caps bit map. |
| #define RSI_HT_CAPS_BIT_MAP \ |
| (RSI_HT_CAPS_NUM_RX_STBC | RSI_HT_CAPS_SHORT_GI_20MHZ | RSI_HT_CAPS_GREENFIELD_EN | RSI_HT_CAPS_SUPPORT_CH_WIDTH) |
| |
| /*=======================================================================*/ |
| //! Scan command parameters |
| /*=======================================================================*/ |
| |
| //! scan channel bit map in 2.4GHz band,valid if given channel to scan is 0 |
| #define RSI_SCAN_CHANNEL_BIT_MAP_2_4 0 |
| |
| //! scan channle bit map in 5GHz band ,valid if given channel to scan is 0 |
| #define RSI_SCAN_CHANNEL_BIT_MAP_5 0 |
| |
| //! scan_feature_bitmap ,valid only if specific channel to scan and ssid are given |
| #define RSI_SCAN_FEAT_BITMAP 0 |
| |
| /*=======================================================================*/ |
| //! Enterprise configuration command parameters |
| /*=======================================================================*/ |
| |
| //! Enterprise method ,should be one of among TLS, TTLS, FAST or PEAP |
| #define RSI_EAP_METHOD "TTLS" |
| //! This parameter is used to configure the module in Enterprise security mode |
| #define RSI_EAP_INNER_METHOD "\"auth=MSCHAPV2\"" |
| //! Private Key Password is required for encrypted private key, format is like "\"12345678\"" |
| #define RSI_PRIVATE_KEY_PASSWORD "" |
| /*=======================================================================*/ |
| //! AP configuration command parameters |
| /*=======================================================================*/ |
| |
| //! This Macro is used to enable AP keep alive functionality |
| #define RSI_AP_KEEP_ALIVE_ENABLE RSI_ENABLE |
| |
| //! This parameter is used to configure keep alive type |
| #define RSI_AP_KEEP_ALIVE_TYPE RSI_NULL_BASED_KEEP_ALIVE |
| |
| //! This parameter is used to configure keep alive period |
| #define RSI_AP_KEEP_ALIVE_PERIOD 100 |
| |
| //! This parameter is used to configure maximum stations supported |
| #define RSI_MAX_STATIONS_SUPPORT 4 |
| /*=======================================================================*/ |
| //! Join command parameters |
| /*=======================================================================*/ |
| |
| //! Tx power level |
| #define RSI_POWER_LEVEL RSI_POWER_LEVEL_HIGH |
| |
| //! RSI_JOIN_FEAT_STA_BG_ONLY_MODE_ENABLE or RSI_JOIN_FEAT_LISTEN_INTERVAL_VALID |
| #if WIFI_ENABLE_SECURITY_WPA3 |
| #define RSI_JOIN_FEAT_BIT_MAP RSI_JOIN_FEAT_MFP_CAPABLE_REQUIRED |
| #else |
| #define RSI_JOIN_FEAT_BIT_MAP 0 |
| #endif |
| |
| #define RSI_LISTEN_INTERVAL 0 |
| |
| //! Transmission data rate. Physical rate at which data has to be transmitted. |
| #define RSI_DATA_RATE RSI_DATA_RATE_AUTO |
| |
| /*=======================================================================*/ |
| //! Ipconf command parameters |
| /*=======================================================================*/ |
| |
| //! DHCP client host name |
| #define RSI_DHCP_HOST_NAME "efr_9116" |
| |
| //! Transmit test command parameters |
| /*=======================================================================*/ |
| //! TX TEST rate flags |
| #define RSI_TX_TEST_RATE_FLAGS 0 |
| |
| //! TX TEST per channel bandwidth |
| #define RSI_TX_TEST_PER_CH_BW 0 |
| |
| //! TX TEST aggregation enable or disable |
| #define RSI_TX_TEST_AGGR_ENABLE RSI_DISABLE |
| |
| //! TX TEST delay |
| #define RSI_TX_TEST_DELAY 0 |
| |
| /*======================================================================*/ |
| //! ssl parameters |
| /*=======================================================================*/ |
| //! ssl version |
| #define RSI_SSL_VERSION 0 |
| |
| //! ssl ciphers |
| #define RSI_SSL_CIPHERS SSL_ALL_CIPHERS |
| |
| //! Enable TCP over SSL with TLS version depends on remote side |
| #define PROTOCOL_DFLT_VERSION BIT(0) |
| |
| //! Enable TCP over SSL with TLS version 1.0 |
| #define PROTOCOL_TLS_1_0 (BIT(0) | BIT(13)) |
| |
| //! Enable TCP over SSL with TLS version 1.1 |
| #define PROTOCOL_TLS_1_1 (BIT(0) | BIT(14)) |
| |
| //! Enable TCP over SSL with TLS version 1.2 |
| #define PROTOCOL_TLS_1_2 (BIT(0) | BIT(15)) |
| /*=======================================================================*/ |
| //! Power save command parameters |
| /*=======================================================================*/ |
| //! set handshake type of power mode |
| #define RSI_HAND_SHAKE_TYPE MSG_BASED |
| |
| //! 0 - LP, 1- ULP mode with RAM retention and 2 - ULP with Non RAM retention |
| #define RSI_SELECT_LP_OR_ULP_MODE RSI_ULP_WITH_RAM_RET |
| |
| //! set DTIM aligment required |
| //! 0 - module wakes up at beacon which is just before or equal to listen_interval |
| //! 1 - module wakes up at DTIM beacon which is just before or equal to listen_interval |
| #define RSI_DTIM_ALIGNED_TYPE 0 |
| |
| //! Monitor interval for the FAST PSP mode |
| //! default is 50 ms, and this parameter is valid for FAST PSP only |
| #define RSI_MONITOR_INTERVAL 50 |
| |
| //! Number of DTIMs to skip during powersave |
| #define RSI_NUM_OF_DTIM_SKIP 0 |
| |
| //! WMM PS parameters |
| //! set wmm enable or disable |
| #define RSI_WMM_PS_ENABLE RSI_DISABLE |
| |
| //! set wmm enable or disable |
| //! 0- TX BASED 1 - PERIODIC |
| #define RSI_WMM_PS_TYPE 0 |
| |
| //! set wmm wake up interval |
| #define RSI_WMM_PS_WAKE_INTERVAL 20 |
| |
| //! set wmm UAPSD bitmap |
| #define RSI_WMM_PS_UAPSD_BITMAP 15 |
| |
| /*=======================================================================*/ |
| //! Socket configuration |
| /*=======================================================================*/ |
| //! RSI_ENABLE or RSI_DISABLE High performance socket |
| #define HIGH_PERFORMANCE_ENABLE RSI_ENABLE //@ RSI_ENABLE or RSI_DISABLE High performance socket |
| #define TOTAL_SOCKETS 10 //@ Total number of sockets. TCP TX + TCP RX + UDP TX + UDP RX |
| #define TOTAL_TCP_SOCKETS 4 //@ Total TCP sockets. TCP TX + TCP RX |
| #define TOTAL_UDP_SOCKETS 4 //@ Total UDP sockets. UDP TX + UDP RX |
| #define TCP_TX_ONLY_SOCKETS 0 //@ Total TCP TX only sockets. TCP TX |
| #define TCP_RX_ONLY_SOCKETS 0 //@ Total TCP RX only sockets. TCP RX |
| #define UDP_TX_ONLY_SOCKETS 0 //@ Total UDP TX only sockets. UDP TX |
| #define UDP_RX_ONLY_SOCKETS 0 //@ Total UDP RX only sockets. UDP RX |
| #define TCP_RX_HIGH_PERFORMANCE_SOCKETS 1 //@ Total TCP RX High Performance sockets |
| #define TCP_RX_WINDOW_SIZE_CAP 10 //@ TCP RX Window size |
| #define TCP_RX_WINDOW_DIV_FACTOR 10 //@ TCP RX Window division factor |
| /*=======================================================================*/ |
| |
| //! Socket Create parameters |
| /*=======================================================================*/ |
| |
| //! Initial timeout for Socket |
| #define RSI_SOCKET_KEEPALIVE_TIMEOUT 1200 |
| |
| //! VAP ID for Concurrent mode |
| #define RSI_VAP_ID 0 |
| |
| //! Timeout for join or scan |
| /*=======================================================================*/ |
| |
| //! RSI_ENABLE or RSI_DISABLE Timeout support |
| #define RSI_TIMEOUT_SUPPORT RSI_DISABLE |
| |
| //! roaming threshold value |
| #define RSI_TIMEOUT_BIT_MAP 1 |
| |
| //! roaming hysterisis value |
| #define RSI_TIMEOUT_VALUE 1500 |
| |
| //! Timeout for ping request |
| /*=======================================================================*/ |
| |
| //! Timeout for PING_REQUEST |
| #define RSI_PING_REQ_TIMEOUT_MS 1000 |
| |
| //! Provide HTTP/HTTPS response status code indication to application e.g 200, 404 etc |
| /*=======================================================================*/ |
| //! Enable or Diable feature |
| #define RSI_HTTP_STATUS_INDICATION_EN RSI_DISABLE |
| /*=======================================================================*/ |
| |
| //! Store Config Profile parameters |
| /*=======================================================================*/ |
| |
| //! Client profile |
| #define RSI_WLAN_PROFILE_CLIENT 0 |
| //! P2P profile |
| #define RSI_WLAN_PROFILE_P2P 1 |
| //! EAP profile |
| #define RSI_WLAN_PROFILE_EAP 2 |
| //! AP profile |
| #define RSI_WLAN_PROFILE_AP 6 |
| //! All profiles |
| #define RSI_WLAN_PROFILE_ALL 0xFF |
| |
| //! AP Config Profile Parameters |
| /*==============================================================================*/ |
| |
| //! Transmission data rate. Physical rate at which data has to be transmitted. |
| #define RSI_CONFIG_AP_DATA_RATE RSI_DATA_RATE_AUTO |
| //! To set wlan feature select bit map |
| #define RSI_CONFIG_AP_WLAN_FEAT_BIT_MAP (FEAT_SECURITY_PSK) |
| //! TCP/IP feature select bitmap for selecting TCP/IP features |
| #define RSI_CONFIG_AP_TCP_IP_FEAT_BIT_MAP (TCP_IP_FEAT_DHCPV4_SERVER) |
| //! To set custom feature select bit map |
| #define RSI_CONFIG_AP_CUSTOM_FEAT_BIT_MAP 0 |
| //! Tx power level |
| #define RSI_CONFIG_AP_TX_POWER RSI_POWER_LEVEL_HIGH |
| //! AP SSID |
| #define RSI_CONFIG_AP_SSID "SILABS_AP" |
| //! RSI_BAND_2P4GHZ(2.4GHz) or RSI_BAND_5GHZ(5GHz) or RSI_DUAL_BAND |
| #define RSI_CONFIG_AP_BAND RSI_BAND_2P4GHZ |
| //! To configure AP channle number |
| #define RSI_CONFIG_AP_CHANNEL 6 |
| //! To configure security type |
| #define RSI_CONFIG_AP_SECURITY_TYPE RSI_WPA |
| //! To configure encryption type |
| #define RSI_CONFIG_AP_ENCRYPTION_TYPE 1 |
| //! To configure PSK |
| #define RSI_CONFIG_AP_PSK "1234567890" |
| //! To configure beacon interval |
| #define RSI_CONFIG_AP_BEACON_INTERVAL 100 |
| //! To configure DTIM period |
| #define RSI_CONFIG_AP_DTIM 2 |
| //! This parameter is used to configure keep alive type |
| #define RSI_CONFIG_AP_KEEP_ALIVE_TYPE 0 //! RSI_NULL_BASED_KEEP_ALIVE |
| |
| #define RSI_CONFIG_AP_KEEP_ALIVE_COUNTER 0 //! 100 |
| //! This parameter is used to configure keep alive period |
| #define RSI_CONFIG_AP_KEEP_ALIVE_PERIOD 100 |
| //! This parameter is used to configure maximum stations supported |
| #define RSI_CONFIG_AP_MAX_STATIONS_COUNT 4 |
| //! P2P Network parameters |
| //! TCP_STACK_USED BIT(0) - IPv4, BIT(1) -IPv6, (BIT(0) | BIT(1)) - Both IPv4 and IPv6 |
| #define RSI_CONFIG_AP_TCP_STACK_USED BIT(0) |
| //! IP address of the module |
| //! E.g: 0x0A0AA8C0 == 192.168.10.10 |
| #define RSI_CONFIG_AP_IP_ADDRESS 0x0A0AA8C0 |
| //! IP address of netmask |
| //! E.g: 0x00FFFFFF == 255.255.255.0 |
| #define RSI_CONFIG_AP_SN_MASK_ADDRESS 0x00FFFFFF |
| //! IP address of Gateway |
| //! E.g: 0x0A0AA8C0 == 192.168.10.10 |
| #define RSI_CONFIG_AP_GATEWAY_ADDRESS 0x0A0AA8C0 |
| |
| //! Client Profile Parameters |
| /* ===================================================================================== */ |
| |
| //! To configure data rate |
| #define RSI_CONFIG_CLIENT_DATA_RATE RSI_DATA_RATE_AUTO |
| //! To configure wlan feature bitmap |
| #define RSI_CONFIG_CLIENT_WLAN_FEAT_BIT_MAP 0 |
| //! To configure tcp/ip feature bitmap |
| #define RSI_CONFIG_CLIENT_TCP_IP_FEAT_BIT_MAP BIT(2) |
| //! To configure custom feature bit map |
| #define RSI_CONFIG_CLIENT_CUSTOM_FEAT_BIT_MAP 0 |
| //! To configure TX power |
| #define RSI_CONFIG_CLIENT_TX_POWER RSI_POWER_LEVEL_HIGH |
| //! To configure listen interval |
| #define RSI_CONFIG_CLIENT_LISTEN_INTERVAL 0 |
| //! To configure SSID |
| #define RSI_CONFIG_CLIENT_SSID "Matter_9116" |
| //! RSI_BAND_2P4GHZ(2.4GHz) or RSI_BAND_5GHZ(5GHz) or RSI_DUAL_BAND |
| #define RSI_CONFIG_CLIENT_BAND RSI_BAND_2P4GHZ |
| //! To configure channel number |
| #define RSI_CONFIG_CLIENT_CHANNEL 0 |
| //! To configure security type |
| #define RSI_CONFIG_CLIENT_SECURITY_TYPE 0 // RSI_WPA |
| //! To configure encryption type |
| #define RSI_CONFIG_CLIENT_ENCRYPTION_TYPE 0 |
| //! To configure PSK |
| #define RSI_CONFIG_CLIENT_PSK "1234567890" |
| //! To configure PMK |
| #define RSI_CONFIG_CLIENT_PMK "" |
| //! Client Network parameters |
| //! TCP_STACK_USED BIT(0) - IPv4, BIT(1) -IPv6, (BIT(0) | BIT(1)) - Both IPv4 and IPv6 |
| #define RSI_CONFIG_CLIENT_TCP_STACK_USED BIT(0) |
| //! DHCP mode 1- Enable 0- Disable |
| //! If DHCP mode is disabled given IP statically |
| #define RSI_CONFIG_CLIENT_DHCP_MODE RSI_DHCP |
| //! IP address of the module |
| //! E.g: 0x0A0AA8C0 == 192.168.10.10 |
| #define RSI_CONFIG_CLIENT_IP_ADDRESS 0x0A0AA8C0 |
| //! IP address of netmask |
| //! E.g: 0x00FFFFFF == 255.255.255.0 |
| #define RSI_CONFIG_CLIENT_SN_MASK_ADDRESS 0x00FFFFFF |
| //! IP address of Gateway |
| //! E.g: 0x010AA8C0 == 192.168.10.1 |
| #define RSI_CONFIG_CLIENT_GATEWAY_ADDRESS 0x010AA8C0 |
| //! scan channel bit map in 2.4GHz band,valid if given channel to scan is 0 |
| #define RSI_CONFIG_CLIENT_SCAN_FEAT_BITMAP 0 |
| //! Scan channel magic code |
| #define RSI_CONFIG_CLIENT_MAGIC_CODE 0x4321 |
| //! scan channel bit map in 2.4GHz band,valid if given channel to scan is 0 |
| #define RSI_CONFIG_CLIENT_SCAN_CHAN_BITMAP_2_4_GHZ 0 |
| //! scan channle bit map in 5GHz band ,valid if given channel to scan is 0 |
| #define RSI_CONFIG_CLIENT_SCAN_CHAN_BITMAP_5_0_GHZ 0 |
| |
| //! EAP Client Profile Parameters |
| /* =========================================================================== */ |
| |
| //! To configure data rate |
| #define RSI_CONFIG_EAP_DATA_RATE RSI_DATA_RATE_AUTO |
| //! To configure wlan feature bitmap |
| #define RSI_CONFIG_EAP_WLAN_FEAT_BIT_MAP 0 |
| //! To configure tcp/ip feature bitmap |
| #define RSI_CONFIG_EAP_TCP_IP_FEAT_BIT_MAP BIT(2) |
| //! To configure custom feature bit map |
| #define RSI_CONFIG_EAP_CUSTOM_FEAT_BIT_MAP 0 |
| //! To configure EAP TX power |
| #define RSI_CONFIG_EAP_TX_POWER RSI_POWER_LEVEL_HIGH |
| //! To Configure scan channel feature bitmap |
| #define RSI_CONFIG_EAP_SCAN_FEAT_BITMAP 0 |
| //! scan channel bit map in 2.4GHz band,valid if given channel to scan is 0 |
| #define RSI_CONFIG_EAP_CHAN_MAGIC_CODE 0 // 0x4321 |
| //! scan channel bit map in 2.4GHz band,valid if given channel to scan is 0 |
| #define RSI_CONFIG_EAP_SCAN_CHAN_BITMAP_2_4_GHZ 0 |
| //! scan channle bit map in 5GHz band ,valid if given channel to scan is 0 |
| #define RSI_CONFIG_EAP_SCAN_CHAN_BITMAP_5_0_GHZ 0 |
| //! To configure SSID |
| #define RSI_CONFIG_EAP_SSID "SILABS_AP" |
| //! RSI_BAND_2P4GHZ(2.4GHz) or RSI_BAND_5GHZ(5GHz) or RSI_DUAL_BAND |
| #define RSI_CONFIG_EAP_BAND RSI_BAND_2P4GHZ |
| //! To set security type |
| #define RSI_CONFIG_EAP_SECURITY_TYPE RSI_WPA2_EAP |
| //! To set encryption type |
| #define RSI_CONFIG_EAP_ENCRYPTION_TYPE 0 |
| //! To set channel number |
| #define RSI_CONFIG_EAP_CHANNEL 0 |
| //! Enterprise method ,should be one of among TLS, TTLS, FAST or PEAP |
| #define RSI_CONFIG_EAP_METHOD "TLS" |
| //! This parameter is used to configure the module in Enterprise security mode |
| #define RSI_CONFIG_EAP_INNER_METHOD "\"auth=MSCHAPV2\"" |
| //! To configure EAP user identity |
| #define RSI_CONFIG_EAP_USER_IDENTITY "\"user1\"" |
| //! TO configure EAP password |
| #define RSI_CONFIG_EAP_PASSWORD "\"test123\"" |
| //! EAP Network parameters |
| //! TCP_STACK_USED BIT(0) - IPv4, BIT(1) -IPv6, (BIT(0) | BIT(1)) - Both IPv4 and IPv6 |
| #define RSI_CONFIG_EAP_TCP_STACK_USED BIT(0) |
| //! DHCP mode 1- Enable 0- Disable |
| //! If DHCP mode is disabled given IP statically |
| #define RSI_CONFIG_EAP_DHCP_MODE RSI_DHCP |
| //! IP address of the module |
| //! E.g: 0x0A0AA8C0 == 192.168.10.10 |
| #define RSI_CONFIG_EAP_IP_ADDRESS 0x0A0AA8C0 |
| //! IP address of netmask |
| //! E.g: 0x00FFFFFF == 255.255.255.0 |
| #define RSI_CONFIG_EAP_SN_MASK_ADDRESS 0x00FFFFFF |
| //! IP address of Gateway |
| //! E.g: 0x010AA8C0 == 192.168.10.1 |
| #define RSI_CONFIG_EAP_GATEWAY_ADDRESS 0x010AA8C0 |
| |
| //! P2P Profile parameters |
| /* ================================================================================= */ |
| |
| //! To configure data rate |
| #define RSI_CONFIG_P2P_DATA_RATE RSI_DATA_RATE_AUTO |
| //! To configure wlan feature bitmap |
| #define RSI_CONFIG_P2P_WLAN_FEAT_BIT_MAP 0 |
| //! To configure P2P tcp/ip feature bitmap |
| #define RSI_CONFIG_P2P_TCP_IP_FEAT_BIT_MAP BIT(2) |
| //! To configure P2P custom feature bitmap |
| #define RSI_CONFIG_P2P_CUSTOM_FEAT_BIT_MAP 0 |
| //! TO configure P2P tx power level |
| #define RSI_CONFIG_P2P_TX_POWER RSI_POWER_LEVEL_HIGH |
| //! Set P2P go intent |
| #define RSI_CONFIG_P2P_GO_INTNET 16 //! Support only Autonomous GO mode |
| //! Set device name |
| #define RSI_CONFIG_P2P_DEVICE_NAME "WSC1.1" |
| //! Set device operating channel |
| #define RSI_CONFIG_P2P_OPERATING_CHANNEL 11 |
| //! Set SSID postfix |
| #define RSI_CONFIG_P2P_SSID_POSTFIX "WSC_1_0_0" |
| //! Set P2P join SSID |
| #define RSI_CONFIG_P2P_JOIN_SSID "SILABS_AP" |
| //! Set psk key |
| #define RSI_CONFIG_P2P_PSK_KEY "12345678" |
| //! P2P Network parameters |
| //! TCP_STACK_USED BIT(0) - IPv4, BIT(1) -IPv6, (BIT(0) | BIT(1)) - Both IPv4 and IPv6 |
| #define RSI_CONFIG_P2P_TCP_STACK_USED BIT(0) |
| //! DHCP mode 1- Enable 0- Disable |
| //! If DHCP mode is disabled given IP statically |
| #define RSI_CONFIG_P2P_DHCP_MODE 1 |
| //! IP address of the module |
| //! E.g: 0x0A0AA8C0 == 192.168.10.10 |
| #define RSI_CONFIG_P2P_IP_ADDRESS 0x0A0AA8C0 |
| //! IP address of netmask |
| //! E.g: 0x00FFFFFF == 255.255.255.0 |
| #define RSI_CONFIG_P2P_SN_MASK_ADDRESS 0x00FFFFFF |
| //! IP address of Gateway |
| //! E.g: 0x010AA8C0 == 192.168.10.1 |
| #define RSI_CONFIG_P2P_GATEWAY_ADDRESS 0x010AA8C0 |
| |
| #endif |
