blob: 171af4f0ba2c240320e71069a542237fba21db24 [file] [log] [blame]
#
# Copyright (c) 2022 Project CHIP Authors
# All rights reserved.
#
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
#
# Description:
# Configuration options CHIP ESP32 demo application.
#
menu "Demo"
choice
prompt "Device Type"
default DEVICE_TYPE_ESP32_DEVKITC if IDF_TARGET_ESP32
default DEVICE_TYPE_ESP32_C3_DEVKITM if IDF_TARGET_ESP32C3
default DEVICE_TYPE_ESP32_C2_DEVKITM if IDF_TARGET_ESP32C2
help
Specifies the type of ESP32 device.
Note that the "ESP32-DevKitC" choice is compatible with a number of clone devices
available from third-party manufacturers.
config DEVICE_TYPE_ESP32_DEVKITC
bool "ESP32-DevKitC"
depends on IDF_TARGET_ESP32
config DEVICE_TYPE_ESP32_WROVER_KIT
bool "ESP32-WROVER-KIT_V4.1"
depends on IDF_TARGET_ESP32
config DEVICE_TYPE_M5STACK
bool "M5Stack"
depends on IDF_TARGET_ESP32
config DEVICE_TYPE_ESP32_C3_DEVKITM
bool "ESP32C3-DevKitM"
depends on IDF_TARGET_ESP32C3
config DEVICE_TYPE_ESP32_C2_DEVKITM
bool "ESP32C2-DevKitM"
depends on IDF_TARGET_ESP32C2
endchoice
choice
prompt "Rendezvous Mode"
default RENDEZVOUS_MODE_BLE if BT_ENABLED
default RENDEZVOUS_MODE_SOFTAP
help
Specifies the Rendezvous mode of the peripheral.
config RENDEZVOUS_MODE_SOFTAP
bool "Soft-AP"
select ESP_WIFI_SOFTAP_SUPPORT
config RENDEZVOUS_MODE_BLE
bool "BLE"
depends on BT_ENABLED
config RENDEZVOUS_MODE_ON_NETWORK
bool "On-Network"
config RENDEZVOUS_MODE_SOFTAP_ON_NETWORK
bool "Soft-AP / On-Network"
select ESP_WIFI_SOFTAP_SUPPORT
config RENDEZVOUS_MODE_BLE_ON_NETWORK
bool "BLE / On-Network"
endchoice
# NOTE: This config is not displayed as a input in the Kconfig menu, as its value is
# entirely derived from the Device Type choice. However the CONFIG_EXAMPLE_DISPLAY_TYPE
# define that is produced is needed to configure the TFT library correctly.
config TFT_PREDEFINED_DISPLAY_TYPE
int
range 0 5
default 0 if DEVICE_TYPE_ESP32_DEVKITC
default 0 if DEVICE_TYPE_ESP32_C3_DEVKITM || DEVICE_TYPE_ESP32_C2_DEVKITM
default 3 if DEVICE_TYPE_M5STACK
default 4 if DEVICE_TYPE_ESP32_WROVER_KIT
config HAVE_DISPLAY
bool
default y if DEVICE_TYPE_M5STACK || DEVICE_TYPE_ESP32_WROVER_KIT
default n if !(DEVICE_TYPE_M5STACK || DEVICE_TYPE_ESP32_WROVER_KIT)
config RENDEZVOUS_MODE
int
range 0 8
default 1 if RENDEZVOUS_MODE_SOFTAP
default 2 if RENDEZVOUS_MODE_BLE
default 4 if RENDEZVOUS_MODE_ON_NETWORK
default 5 if RENDEZVOUS_MODE_SOFTAP_ON_NETWORK
default 6 if RENDEZVOUS_MODE_BLE_ON_NETWORK
config DISPLAY_AUTO_OFF
bool "Automatically turn off the M5Stack's Display after a few seconds"
default "y"
depends on DEVICE_TYPE_M5STACK
help
To reduce wear and heat the M5Stack's Display is automatically switched off after a few seconds
config STATUS_LED_GPIO_NUM
int
range 0 40
default 2 if DEVICE_TYPE_ESP32_DEVKITC #Use LED1 (blue LED) as status LED on DevKitC
default 8 if DEVICE_TYPE_ESP32_C3_DEVKITM || DEVICE_TYPE_ESP32_C2_DEVKITM
default 26 if DEVICE_TYPE_ESP32_WROVER_KIT
default 40 if DEVICE_TYPE_M5STACK
help
Each board has a status led, define its pin number.
endmenu
menu "PW RPC Debug channel"
depends on ENABLE_PW_RPC
config EXAMPLE_UART_PORT_NUM
int "UART port number"
range 0 2 if IDF_TARGET_ESP32
range 0 1 if IDF_TARGET_ESP32C3
default 0
help
UART communication port number for the example.
See UART documentation for available port numbers.
config EXAMPLE_UART_BAUD_RATE
int "UART communication speed"
range 1200 115200
default 115200
help
UART communication speed for Modbus example.
config EXAMPLE_UART_RXD
int "UART RXD pin number"
range 0 34 if IDF_TARGET_ESP32
range 0 19 if IDF_TARGET_ESP32C3
default 5
help
GPIO number for UART RX pin. See UART documentation for more information
about available pin numbers for UART.
config EXAMPLE_UART_TXD
int "UART TXD pin number"
range 0 34 if IDF_TARGET_ESP32
range 0 19 if IDF_TARGET_ESP32C3
default 4
help
GPIO number for UART TX pin. See UART documentation for more information
about available pin numbers for UART.
endmenu