| # |
| # Copyright (c) 2021 Project CHIP Authors |
| # All rights reserved. |
| # |
| # Licensed under the Apache License, Version 2.0 (the "License"); |
| # you may not use this file except in compliance with the License. |
| # You may obtain a copy of the License at |
| # |
| # http://www.apache.org/licenses/LICENSE-2.0 |
| # |
| # Unless required by applicable law or agreed to in writing, software |
| # distributed under the License is distributed on an "AS IS" BASIS, |
| # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| # See the License for the specific language governing permissions and |
| # limitations under the License. |
| # |
| # Description: |
| # Some useful defaults for the demo app configuration. |
| # |
| |
| # Default to 921600 baud when flashing and monitoring device |
| CONFIG_ESPTOOLPY_BAUD_921600B=y |
| CONFIG_ESPTOOLPY_BAUD=921600 |
| CONFIG_ESPTOOLPY_COMPRESSED=y |
| CONFIG_ESPTOOLPY_MONITOR_BAUD_115200B=y |
| CONFIG_ESPTOOLPY_MONITOR_BAUD=115200 |
| |
| #enable BT |
| CONFIG_BT_ENABLED=y |
| CONFIG_BT_NIMBLE_ENABLED=y |
| |
| #disable BT connection reattempt |
| CONFIG_BT_NIMBLE_ENABLE_CONN_REATTEMPT=n |
| |
| #enable lwip ipv6 autoconfig |
| CONFIG_LWIP_IPV6_AUTOCONFIG=y |
| |
| #enable debug shell |
| CONFIG_ENABLE_CHIP_SHELL=y |
| |
| # Use a custom partition table |
| CONFIG_PARTITION_TABLE_CUSTOM=y |
| CONFIG_PARTITION_TABLE_FILENAME="partitions.csv" |
| |
| #enable lwIP route hooks |
| CONFIG_LWIP_HOOK_IP6_ROUTE_DEFAULT=y |
| CONFIG_LWIP_HOOK_ND6_GET_GW_DEFAULT=y |
| |
| # Serial Flasher config |
| CONFIG_ESPTOOLPY_FLASHSIZE_4MB=y |
| CONFIG_ESPTOOLPY_FLASHSIZE="4MB" |
| |
| # Disable softap support by default |
| CONFIG_ESP_WIFI_SOFTAP_SUPPORT=n |
| # This example uses the older version of RMT driver to work with both |
| # idf-v4.4.3 and idf-v5.0, so suppressing the warnings by setting below option |
| CONFIG_RMT_SUPPRESS_DEPRECATE_WARN=y |
| |
| # Enable HKDF in mbedtls |
| CONFIG_MBEDTLS_HKDF_C=y |
| |
| # Disable Read Client |
| CONFIG_DISABLE_READ_CLIENT=y |
| |
| # Increase LwIP IPv6 address number |
| CONFIG_LWIP_IPV6_NUM_ADDRESSES=6 |
| |
| # Enable sntp time sync |
| CONFIG_ENABLE_SNTP_TIME_SYNC=y |
| |
| # Enable EVSE device on EP1 |
| CONFIG_CHIP_DEVICE_CONFIG_ENABLE_EVSE=y |
| |
| # Enable test triggers used by the Device Energy Management tests |
| CONFIG_CHIP_DEVICE_CONFIG_ENABLE_DEVICE_ENERGY_MANAGEMENT_TRIGGER=y |
| |
| # Enable test triggers used by the Evse tests |
| CONFIG_CHIP_DEVICE_CONFIG_ENABLE_ENERGY_EVSE_TRIGGER=y |
| |
| # Enable test triggers used by the Water Heater Management tests |
| CONFIG_CHIP_DEVICE_CONFIG_ENABLE_WATER_HEATER_MANAGEMENT_TRIGGER=y |
| |
| # Enable test triggers used by the Electrical Reporting tests |
| CONFIG_CHIP_DEVICE_CONFIG_ENABLE_ENERGY_REPORTING_TRIGGER=y |
| |
| # Ensure kPowerForecastReporting (PFR) is set in the DeviceEnergyManagement::Feature attribute. Note cannot set PFR and SFR. |
| CONFIG_DEM_SUPPORT_POWER_FORECAST_REPORTING=y |