src/app/tests/suites/certification/Test_TC_DRYERCTRL_2_1.yaml

# Copyright (c) 2023 Project CHIP Authors
#
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.

name: 3.2.1. [TC-DRYERCTRL-2.1]  Optional Dryness attributes with server as DUT

PICS:
    - DRYERCTRL.S

config:
    nodeId: 0x12344321
    cluster: "Laundry Dryer Controls"
    endpoint: 1

    unsupportedSelectedDrynessLevel:
        type: int8u
        defaultValue: 4

    SupportedDrynessLevel:
        type: int8u
        defaultValue: 1

tests:
    - label: "Step 1: Wait for the commissioned device to be retrieved"
      cluster: "DelayCommands"
      command: "WaitForCommissionee"
      arguments:
          values:
              - name: "nodeId"
                value: nodeId

    - label:
          "Step 2: TH reads from the DUT the mandatory attribute:
          SupportedDrynessLevels"
      PICS: DRYERCTRL.S.A0000
      command: "readAttribute"
      attribute: "SupportedDrynessLevels"
      response:
          constraints:
              type: list
              maxLength: 4

    - label:
          "Step 3: TH reads from the DUT the mandatory attribute:
          SelectedDrynessLevel"
      PICS: DRYERCTRL.S.A0001
      command: "readAttribute"
      attribute: "SelectedDrynessLevel"
      response:
          constraints:
              type: enum8
              minValue: 0
              maxValue: 3

    - label:
          "Step 4:TH writes a supported SelectedDrynessLevel attribute that is
          within the list of SupportedDrynessLevels"
      PICS: DRYERCTRL.S.A0001
      command: "writeAttribute"
      attribute: "SelectedDrynessLevel"
      arguments:
          value: SupportedDrynessLevel

    - label: "Wait 2 seconds"
      cluster: "DelayCommands"
      command: "WaitForMs"
      arguments:
          values:
              - name: "ms"
                value: 2000

    - label:
          "Step 5: after a few seconds, TH reads from the DUT the
          SelectedDrynessLevel attribute"
      PICS: DRYERCTRL.S.A0001
      command: "readAttribute"
      attribute: "SelectedDrynessLevel"
      response:
          value: SupportedDrynessLevel
          constraints:
              type: enum8

    - label:
          "Step 6: TH writes an unsupported SelectedDrynessLevel attribute that
          is not in list of SupportedDrynessLevels to DUT"
      PICS: DRYERCTRL.S.A0001
      command: "writeAttribute"
      attribute: "SelectedDrynessLevel"
      arguments:
          value: unsupportedSelectedDrynessLevel
      response:
          error: CONSTRAINT_ERROR

    - label: "Step 6: Operate device to set the condition to read only"
      verification: |
          Manual operation required
      cluster: "LogCommands"
      command: "UserPrompt"
      PICS: PICS_SKIP_SAMPLE_APP && DRYERCTRL.S.M.ManuallyControlled
      arguments:
          values:
              - name: "message"
                value: "Please enter 'y' for success"
              - name: "expectedValue"
                value: "y"

    - label:
          "Step 7: TH writes a supported SelectedDrynessLevel attribute to DUT
          while DUT is not in a valid state."
      PICS: DRYERCTRL.S.M.ManuallyControlled && DRYERCTRL.S.A0001
      command: "writeAttribute"
      attribute: "SelectedDrynessLevel"
      arguments:
          value: SupportedDrynessLevel
      response:
          error: INVALID_IN_STATE