| /** |
| * Copyright (c) 2021 Raspberry Pi (Trading) Ltd. |
| * |
| * SPDX-License-Identifier: BSD-3-Clause |
| */ |
| // ============================================================================= |
| // Register block : CLOCKS |
| // Version : 1 |
| // Bus type : apb |
| // Description : None |
| // ============================================================================= |
| #ifndef HARDWARE_REGS_CLOCKS_DEFINED |
| #define HARDWARE_REGS_CLOCKS_DEFINED |
| // ============================================================================= |
| // Register : CLOCKS_CLK_GPOUT0_CTRL |
| // Description : Clock control, can be changed on-the-fly (except for auxsrc) |
| #define CLOCKS_CLK_GPOUT0_CTRL_OFFSET _u(0x00000000) |
| #define CLOCKS_CLK_GPOUT0_CTRL_BITS _u(0x00131de0) |
| #define CLOCKS_CLK_GPOUT0_CTRL_RESET _u(0x00000000) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT0_CTRL_NUDGE |
| // Description : An edge on this signal shifts the phase of the output by 1 |
| // cycle of the input clock |
| // This can be done at any time |
| #define CLOCKS_CLK_GPOUT0_CTRL_NUDGE_RESET _u(0x0) |
| #define CLOCKS_CLK_GPOUT0_CTRL_NUDGE_BITS _u(0x00100000) |
| #define CLOCKS_CLK_GPOUT0_CTRL_NUDGE_MSB _u(20) |
| #define CLOCKS_CLK_GPOUT0_CTRL_NUDGE_LSB _u(20) |
| #define CLOCKS_CLK_GPOUT0_CTRL_NUDGE_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT0_CTRL_PHASE |
| // Description : This delays the enable signal by up to 3 cycles of the input |
| // clock |
| // This must be set before the clock is enabled to have any effect |
| #define CLOCKS_CLK_GPOUT0_CTRL_PHASE_RESET _u(0x0) |
| #define CLOCKS_CLK_GPOUT0_CTRL_PHASE_BITS _u(0x00030000) |
| #define CLOCKS_CLK_GPOUT0_CTRL_PHASE_MSB _u(17) |
| #define CLOCKS_CLK_GPOUT0_CTRL_PHASE_LSB _u(16) |
| #define CLOCKS_CLK_GPOUT0_CTRL_PHASE_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT0_CTRL_DC50 |
| // Description : Enables duty cycle correction for odd divisors |
| #define CLOCKS_CLK_GPOUT0_CTRL_DC50_RESET _u(0x0) |
| #define CLOCKS_CLK_GPOUT0_CTRL_DC50_BITS _u(0x00001000) |
| #define CLOCKS_CLK_GPOUT0_CTRL_DC50_MSB _u(12) |
| #define CLOCKS_CLK_GPOUT0_CTRL_DC50_LSB _u(12) |
| #define CLOCKS_CLK_GPOUT0_CTRL_DC50_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT0_CTRL_ENABLE |
| // Description : Starts and stops the clock generator cleanly |
| #define CLOCKS_CLK_GPOUT0_CTRL_ENABLE_RESET _u(0x0) |
| #define CLOCKS_CLK_GPOUT0_CTRL_ENABLE_BITS _u(0x00000800) |
| #define CLOCKS_CLK_GPOUT0_CTRL_ENABLE_MSB _u(11) |
| #define CLOCKS_CLK_GPOUT0_CTRL_ENABLE_LSB _u(11) |
| #define CLOCKS_CLK_GPOUT0_CTRL_ENABLE_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT0_CTRL_KILL |
| // Description : Asynchronously kills the clock generator |
| #define CLOCKS_CLK_GPOUT0_CTRL_KILL_RESET _u(0x0) |
| #define CLOCKS_CLK_GPOUT0_CTRL_KILL_BITS _u(0x00000400) |
| #define CLOCKS_CLK_GPOUT0_CTRL_KILL_MSB _u(10) |
| #define CLOCKS_CLK_GPOUT0_CTRL_KILL_LSB _u(10) |
| #define CLOCKS_CLK_GPOUT0_CTRL_KILL_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT0_CTRL_AUXSRC |
| // Description : Selects the auxiliary clock source, will glitch when switching |
| // 0x0 -> clksrc_pll_sys |
| // 0x1 -> clksrc_gpin0 |
| // 0x2 -> clksrc_gpin1 |
| // 0x3 -> clksrc_pll_usb |
| // 0x4 -> rosc_clksrc |
| // 0x5 -> xosc_clksrc |
| // 0x6 -> clk_sys |
| // 0x7 -> clk_usb |
| // 0x8 -> clk_adc |
| // 0x9 -> clk_rtc |
| // 0xa -> clk_ref |
| #define CLOCKS_CLK_GPOUT0_CTRL_AUXSRC_RESET _u(0x0) |
| #define CLOCKS_CLK_GPOUT0_CTRL_AUXSRC_BITS _u(0x000001e0) |
| #define CLOCKS_CLK_GPOUT0_CTRL_AUXSRC_MSB _u(8) |
| #define CLOCKS_CLK_GPOUT0_CTRL_AUXSRC_LSB _u(5) |
| #define CLOCKS_CLK_GPOUT0_CTRL_AUXSRC_ACCESS "RW" |
| #define CLOCKS_CLK_GPOUT0_CTRL_AUXSRC_VALUE_CLKSRC_PLL_SYS _u(0x0) |
| #define CLOCKS_CLK_GPOUT0_CTRL_AUXSRC_VALUE_CLKSRC_GPIN0 _u(0x1) |
| #define CLOCKS_CLK_GPOUT0_CTRL_AUXSRC_VALUE_CLKSRC_GPIN1 _u(0x2) |
| #define CLOCKS_CLK_GPOUT0_CTRL_AUXSRC_VALUE_CLKSRC_PLL_USB _u(0x3) |
| #define CLOCKS_CLK_GPOUT0_CTRL_AUXSRC_VALUE_ROSC_CLKSRC _u(0x4) |
| #define CLOCKS_CLK_GPOUT0_CTRL_AUXSRC_VALUE_XOSC_CLKSRC _u(0x5) |
| #define CLOCKS_CLK_GPOUT0_CTRL_AUXSRC_VALUE_CLK_SYS _u(0x6) |
| #define CLOCKS_CLK_GPOUT0_CTRL_AUXSRC_VALUE_CLK_USB _u(0x7) |
| #define CLOCKS_CLK_GPOUT0_CTRL_AUXSRC_VALUE_CLK_ADC _u(0x8) |
| #define CLOCKS_CLK_GPOUT0_CTRL_AUXSRC_VALUE_CLK_RTC _u(0x9) |
| #define CLOCKS_CLK_GPOUT0_CTRL_AUXSRC_VALUE_CLK_REF _u(0xa) |
| // ============================================================================= |
| // Register : CLOCKS_CLK_GPOUT0_DIV |
| // Description : Clock divisor, can be changed on-the-fly |
| #define CLOCKS_CLK_GPOUT0_DIV_OFFSET _u(0x00000004) |
| #define CLOCKS_CLK_GPOUT0_DIV_BITS _u(0xffffffff) |
| #define CLOCKS_CLK_GPOUT0_DIV_RESET _u(0x00000100) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT0_DIV_INT |
| // Description : Integer component of the divisor, 0 -> divide by 2^16 |
| #define CLOCKS_CLK_GPOUT0_DIV_INT_RESET _u(0x000001) |
| #define CLOCKS_CLK_GPOUT0_DIV_INT_BITS _u(0xffffff00) |
| #define CLOCKS_CLK_GPOUT0_DIV_INT_MSB _u(31) |
| #define CLOCKS_CLK_GPOUT0_DIV_INT_LSB _u(8) |
| #define CLOCKS_CLK_GPOUT0_DIV_INT_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT0_DIV_FRAC |
| // Description : Fractional component of the divisor |
| #define CLOCKS_CLK_GPOUT0_DIV_FRAC_RESET _u(0x00) |
| #define CLOCKS_CLK_GPOUT0_DIV_FRAC_BITS _u(0x000000ff) |
| #define CLOCKS_CLK_GPOUT0_DIV_FRAC_MSB _u(7) |
| #define CLOCKS_CLK_GPOUT0_DIV_FRAC_LSB _u(0) |
| #define CLOCKS_CLK_GPOUT0_DIV_FRAC_ACCESS "RW" |
| // ============================================================================= |
| // Register : CLOCKS_CLK_GPOUT0_SELECTED |
| // Description : Indicates which SRC is currently selected by the glitchless mux |
| // (one-hot). |
| // This slice does not have a glitchless mux (only the AUX_SRC |
| // field is present, not SRC) so this register is hardwired to |
| // 0x1. |
| #define CLOCKS_CLK_GPOUT0_SELECTED_OFFSET _u(0x00000008) |
| #define CLOCKS_CLK_GPOUT0_SELECTED_BITS _u(0xffffffff) |
| #define CLOCKS_CLK_GPOUT0_SELECTED_RESET _u(0x00000001) |
| #define CLOCKS_CLK_GPOUT0_SELECTED_MSB _u(31) |
| #define CLOCKS_CLK_GPOUT0_SELECTED_LSB _u(0) |
| #define CLOCKS_CLK_GPOUT0_SELECTED_ACCESS "RO" |
| // ============================================================================= |
| // Register : CLOCKS_CLK_GPOUT1_CTRL |
| // Description : Clock control, can be changed on-the-fly (except for auxsrc) |
| #define CLOCKS_CLK_GPOUT1_CTRL_OFFSET _u(0x0000000c) |
| #define CLOCKS_CLK_GPOUT1_CTRL_BITS _u(0x00131de0) |
| #define CLOCKS_CLK_GPOUT1_CTRL_RESET _u(0x00000000) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT1_CTRL_NUDGE |
| // Description : An edge on this signal shifts the phase of the output by 1 |
| // cycle of the input clock |
| // This can be done at any time |
| #define CLOCKS_CLK_GPOUT1_CTRL_NUDGE_RESET _u(0x0) |
| #define CLOCKS_CLK_GPOUT1_CTRL_NUDGE_BITS _u(0x00100000) |
| #define CLOCKS_CLK_GPOUT1_CTRL_NUDGE_MSB _u(20) |
| #define CLOCKS_CLK_GPOUT1_CTRL_NUDGE_LSB _u(20) |
| #define CLOCKS_CLK_GPOUT1_CTRL_NUDGE_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT1_CTRL_PHASE |
| // Description : This delays the enable signal by up to 3 cycles of the input |
| // clock |
| // This must be set before the clock is enabled to have any effect |
| #define CLOCKS_CLK_GPOUT1_CTRL_PHASE_RESET _u(0x0) |
| #define CLOCKS_CLK_GPOUT1_CTRL_PHASE_BITS _u(0x00030000) |
| #define CLOCKS_CLK_GPOUT1_CTRL_PHASE_MSB _u(17) |
| #define CLOCKS_CLK_GPOUT1_CTRL_PHASE_LSB _u(16) |
| #define CLOCKS_CLK_GPOUT1_CTRL_PHASE_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT1_CTRL_DC50 |
| // Description : Enables duty cycle correction for odd divisors |
| #define CLOCKS_CLK_GPOUT1_CTRL_DC50_RESET _u(0x0) |
| #define CLOCKS_CLK_GPOUT1_CTRL_DC50_BITS _u(0x00001000) |
| #define CLOCKS_CLK_GPOUT1_CTRL_DC50_MSB _u(12) |
| #define CLOCKS_CLK_GPOUT1_CTRL_DC50_LSB _u(12) |
| #define CLOCKS_CLK_GPOUT1_CTRL_DC50_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT1_CTRL_ENABLE |
| // Description : Starts and stops the clock generator cleanly |
| #define CLOCKS_CLK_GPOUT1_CTRL_ENABLE_RESET _u(0x0) |
| #define CLOCKS_CLK_GPOUT1_CTRL_ENABLE_BITS _u(0x00000800) |
| #define CLOCKS_CLK_GPOUT1_CTRL_ENABLE_MSB _u(11) |
| #define CLOCKS_CLK_GPOUT1_CTRL_ENABLE_LSB _u(11) |
| #define CLOCKS_CLK_GPOUT1_CTRL_ENABLE_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT1_CTRL_KILL |
| // Description : Asynchronously kills the clock generator |
| #define CLOCKS_CLK_GPOUT1_CTRL_KILL_RESET _u(0x0) |
| #define CLOCKS_CLK_GPOUT1_CTRL_KILL_BITS _u(0x00000400) |
| #define CLOCKS_CLK_GPOUT1_CTRL_KILL_MSB _u(10) |
| #define CLOCKS_CLK_GPOUT1_CTRL_KILL_LSB _u(10) |
| #define CLOCKS_CLK_GPOUT1_CTRL_KILL_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT1_CTRL_AUXSRC |
| // Description : Selects the auxiliary clock source, will glitch when switching |
| // 0x0 -> clksrc_pll_sys |
| // 0x1 -> clksrc_gpin0 |
| // 0x2 -> clksrc_gpin1 |
| // 0x3 -> clksrc_pll_usb |
| // 0x4 -> rosc_clksrc |
| // 0x5 -> xosc_clksrc |
| // 0x6 -> clk_sys |
| // 0x7 -> clk_usb |
| // 0x8 -> clk_adc |
| // 0x9 -> clk_rtc |
| // 0xa -> clk_ref |
| #define CLOCKS_CLK_GPOUT1_CTRL_AUXSRC_RESET _u(0x0) |
| #define CLOCKS_CLK_GPOUT1_CTRL_AUXSRC_BITS _u(0x000001e0) |
| #define CLOCKS_CLK_GPOUT1_CTRL_AUXSRC_MSB _u(8) |
| #define CLOCKS_CLK_GPOUT1_CTRL_AUXSRC_LSB _u(5) |
| #define CLOCKS_CLK_GPOUT1_CTRL_AUXSRC_ACCESS "RW" |
| #define CLOCKS_CLK_GPOUT1_CTRL_AUXSRC_VALUE_CLKSRC_PLL_SYS _u(0x0) |
| #define CLOCKS_CLK_GPOUT1_CTRL_AUXSRC_VALUE_CLKSRC_GPIN0 _u(0x1) |
| #define CLOCKS_CLK_GPOUT1_CTRL_AUXSRC_VALUE_CLKSRC_GPIN1 _u(0x2) |
| #define CLOCKS_CLK_GPOUT1_CTRL_AUXSRC_VALUE_CLKSRC_PLL_USB _u(0x3) |
| #define CLOCKS_CLK_GPOUT1_CTRL_AUXSRC_VALUE_ROSC_CLKSRC _u(0x4) |
| #define CLOCKS_CLK_GPOUT1_CTRL_AUXSRC_VALUE_XOSC_CLKSRC _u(0x5) |
| #define CLOCKS_CLK_GPOUT1_CTRL_AUXSRC_VALUE_CLK_SYS _u(0x6) |
| #define CLOCKS_CLK_GPOUT1_CTRL_AUXSRC_VALUE_CLK_USB _u(0x7) |
| #define CLOCKS_CLK_GPOUT1_CTRL_AUXSRC_VALUE_CLK_ADC _u(0x8) |
| #define CLOCKS_CLK_GPOUT1_CTRL_AUXSRC_VALUE_CLK_RTC _u(0x9) |
| #define CLOCKS_CLK_GPOUT1_CTRL_AUXSRC_VALUE_CLK_REF _u(0xa) |
| // ============================================================================= |
| // Register : CLOCKS_CLK_GPOUT1_DIV |
| // Description : Clock divisor, can be changed on-the-fly |
| #define CLOCKS_CLK_GPOUT1_DIV_OFFSET _u(0x00000010) |
| #define CLOCKS_CLK_GPOUT1_DIV_BITS _u(0xffffffff) |
| #define CLOCKS_CLK_GPOUT1_DIV_RESET _u(0x00000100) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT1_DIV_INT |
| // Description : Integer component of the divisor, 0 -> divide by 2^16 |
| #define CLOCKS_CLK_GPOUT1_DIV_INT_RESET _u(0x000001) |
| #define CLOCKS_CLK_GPOUT1_DIV_INT_BITS _u(0xffffff00) |
| #define CLOCKS_CLK_GPOUT1_DIV_INT_MSB _u(31) |
| #define CLOCKS_CLK_GPOUT1_DIV_INT_LSB _u(8) |
| #define CLOCKS_CLK_GPOUT1_DIV_INT_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT1_DIV_FRAC |
| // Description : Fractional component of the divisor |
| #define CLOCKS_CLK_GPOUT1_DIV_FRAC_RESET _u(0x00) |
| #define CLOCKS_CLK_GPOUT1_DIV_FRAC_BITS _u(0x000000ff) |
| #define CLOCKS_CLK_GPOUT1_DIV_FRAC_MSB _u(7) |
| #define CLOCKS_CLK_GPOUT1_DIV_FRAC_LSB _u(0) |
| #define CLOCKS_CLK_GPOUT1_DIV_FRAC_ACCESS "RW" |
| // ============================================================================= |
| // Register : CLOCKS_CLK_GPOUT1_SELECTED |
| // Description : Indicates which SRC is currently selected by the glitchless mux |
| // (one-hot). |
| // This slice does not have a glitchless mux (only the AUX_SRC |
| // field is present, not SRC) so this register is hardwired to |
| // 0x1. |
| #define CLOCKS_CLK_GPOUT1_SELECTED_OFFSET _u(0x00000014) |
| #define CLOCKS_CLK_GPOUT1_SELECTED_BITS _u(0xffffffff) |
| #define CLOCKS_CLK_GPOUT1_SELECTED_RESET _u(0x00000001) |
| #define CLOCKS_CLK_GPOUT1_SELECTED_MSB _u(31) |
| #define CLOCKS_CLK_GPOUT1_SELECTED_LSB _u(0) |
| #define CLOCKS_CLK_GPOUT1_SELECTED_ACCESS "RO" |
| // ============================================================================= |
| // Register : CLOCKS_CLK_GPOUT2_CTRL |
| // Description : Clock control, can be changed on-the-fly (except for auxsrc) |
| #define CLOCKS_CLK_GPOUT2_CTRL_OFFSET _u(0x00000018) |
| #define CLOCKS_CLK_GPOUT2_CTRL_BITS _u(0x00131de0) |
| #define CLOCKS_CLK_GPOUT2_CTRL_RESET _u(0x00000000) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT2_CTRL_NUDGE |
| // Description : An edge on this signal shifts the phase of the output by 1 |
| // cycle of the input clock |
| // This can be done at any time |
| #define CLOCKS_CLK_GPOUT2_CTRL_NUDGE_RESET _u(0x0) |
| #define CLOCKS_CLK_GPOUT2_CTRL_NUDGE_BITS _u(0x00100000) |
| #define CLOCKS_CLK_GPOUT2_CTRL_NUDGE_MSB _u(20) |
| #define CLOCKS_CLK_GPOUT2_CTRL_NUDGE_LSB _u(20) |
| #define CLOCKS_CLK_GPOUT2_CTRL_NUDGE_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT2_CTRL_PHASE |
| // Description : This delays the enable signal by up to 3 cycles of the input |
| // clock |
| // This must be set before the clock is enabled to have any effect |
| #define CLOCKS_CLK_GPOUT2_CTRL_PHASE_RESET _u(0x0) |
| #define CLOCKS_CLK_GPOUT2_CTRL_PHASE_BITS _u(0x00030000) |
| #define CLOCKS_CLK_GPOUT2_CTRL_PHASE_MSB _u(17) |
| #define CLOCKS_CLK_GPOUT2_CTRL_PHASE_LSB _u(16) |
| #define CLOCKS_CLK_GPOUT2_CTRL_PHASE_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT2_CTRL_DC50 |
| // Description : Enables duty cycle correction for odd divisors |
| #define CLOCKS_CLK_GPOUT2_CTRL_DC50_RESET _u(0x0) |
| #define CLOCKS_CLK_GPOUT2_CTRL_DC50_BITS _u(0x00001000) |
| #define CLOCKS_CLK_GPOUT2_CTRL_DC50_MSB _u(12) |
| #define CLOCKS_CLK_GPOUT2_CTRL_DC50_LSB _u(12) |
| #define CLOCKS_CLK_GPOUT2_CTRL_DC50_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT2_CTRL_ENABLE |
| // Description : Starts and stops the clock generator cleanly |
| #define CLOCKS_CLK_GPOUT2_CTRL_ENABLE_RESET _u(0x0) |
| #define CLOCKS_CLK_GPOUT2_CTRL_ENABLE_BITS _u(0x00000800) |
| #define CLOCKS_CLK_GPOUT2_CTRL_ENABLE_MSB _u(11) |
| #define CLOCKS_CLK_GPOUT2_CTRL_ENABLE_LSB _u(11) |
| #define CLOCKS_CLK_GPOUT2_CTRL_ENABLE_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT2_CTRL_KILL |
| // Description : Asynchronously kills the clock generator |
| #define CLOCKS_CLK_GPOUT2_CTRL_KILL_RESET _u(0x0) |
| #define CLOCKS_CLK_GPOUT2_CTRL_KILL_BITS _u(0x00000400) |
| #define CLOCKS_CLK_GPOUT2_CTRL_KILL_MSB _u(10) |
| #define CLOCKS_CLK_GPOUT2_CTRL_KILL_LSB _u(10) |
| #define CLOCKS_CLK_GPOUT2_CTRL_KILL_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT2_CTRL_AUXSRC |
| // Description : Selects the auxiliary clock source, will glitch when switching |
| // 0x0 -> clksrc_pll_sys |
| // 0x1 -> clksrc_gpin0 |
| // 0x2 -> clksrc_gpin1 |
| // 0x3 -> clksrc_pll_usb |
| // 0x4 -> rosc_clksrc_ph |
| // 0x5 -> xosc_clksrc |
| // 0x6 -> clk_sys |
| // 0x7 -> clk_usb |
| // 0x8 -> clk_adc |
| // 0x9 -> clk_rtc |
| // 0xa -> clk_ref |
| #define CLOCKS_CLK_GPOUT2_CTRL_AUXSRC_RESET _u(0x0) |
| #define CLOCKS_CLK_GPOUT2_CTRL_AUXSRC_BITS _u(0x000001e0) |
| #define CLOCKS_CLK_GPOUT2_CTRL_AUXSRC_MSB _u(8) |
| #define CLOCKS_CLK_GPOUT2_CTRL_AUXSRC_LSB _u(5) |
| #define CLOCKS_CLK_GPOUT2_CTRL_AUXSRC_ACCESS "RW" |
| #define CLOCKS_CLK_GPOUT2_CTRL_AUXSRC_VALUE_CLKSRC_PLL_SYS _u(0x0) |
| #define CLOCKS_CLK_GPOUT2_CTRL_AUXSRC_VALUE_CLKSRC_GPIN0 _u(0x1) |
| #define CLOCKS_CLK_GPOUT2_CTRL_AUXSRC_VALUE_CLKSRC_GPIN1 _u(0x2) |
| #define CLOCKS_CLK_GPOUT2_CTRL_AUXSRC_VALUE_CLKSRC_PLL_USB _u(0x3) |
| #define CLOCKS_CLK_GPOUT2_CTRL_AUXSRC_VALUE_ROSC_CLKSRC_PH _u(0x4) |
| #define CLOCKS_CLK_GPOUT2_CTRL_AUXSRC_VALUE_XOSC_CLKSRC _u(0x5) |
| #define CLOCKS_CLK_GPOUT2_CTRL_AUXSRC_VALUE_CLK_SYS _u(0x6) |
| #define CLOCKS_CLK_GPOUT2_CTRL_AUXSRC_VALUE_CLK_USB _u(0x7) |
| #define CLOCKS_CLK_GPOUT2_CTRL_AUXSRC_VALUE_CLK_ADC _u(0x8) |
| #define CLOCKS_CLK_GPOUT2_CTRL_AUXSRC_VALUE_CLK_RTC _u(0x9) |
| #define CLOCKS_CLK_GPOUT2_CTRL_AUXSRC_VALUE_CLK_REF _u(0xa) |
| // ============================================================================= |
| // Register : CLOCKS_CLK_GPOUT2_DIV |
| // Description : Clock divisor, can be changed on-the-fly |
| #define CLOCKS_CLK_GPOUT2_DIV_OFFSET _u(0x0000001c) |
| #define CLOCKS_CLK_GPOUT2_DIV_BITS _u(0xffffffff) |
| #define CLOCKS_CLK_GPOUT2_DIV_RESET _u(0x00000100) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT2_DIV_INT |
| // Description : Integer component of the divisor, 0 -> divide by 2^16 |
| #define CLOCKS_CLK_GPOUT2_DIV_INT_RESET _u(0x000001) |
| #define CLOCKS_CLK_GPOUT2_DIV_INT_BITS _u(0xffffff00) |
| #define CLOCKS_CLK_GPOUT2_DIV_INT_MSB _u(31) |
| #define CLOCKS_CLK_GPOUT2_DIV_INT_LSB _u(8) |
| #define CLOCKS_CLK_GPOUT2_DIV_INT_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT2_DIV_FRAC |
| // Description : Fractional component of the divisor |
| #define CLOCKS_CLK_GPOUT2_DIV_FRAC_RESET _u(0x00) |
| #define CLOCKS_CLK_GPOUT2_DIV_FRAC_BITS _u(0x000000ff) |
| #define CLOCKS_CLK_GPOUT2_DIV_FRAC_MSB _u(7) |
| #define CLOCKS_CLK_GPOUT2_DIV_FRAC_LSB _u(0) |
| #define CLOCKS_CLK_GPOUT2_DIV_FRAC_ACCESS "RW" |
| // ============================================================================= |
| // Register : CLOCKS_CLK_GPOUT2_SELECTED |
| // Description : Indicates which SRC is currently selected by the glitchless mux |
| // (one-hot). |
| // This slice does not have a glitchless mux (only the AUX_SRC |
| // field is present, not SRC) so this register is hardwired to |
| // 0x1. |
| #define CLOCKS_CLK_GPOUT2_SELECTED_OFFSET _u(0x00000020) |
| #define CLOCKS_CLK_GPOUT2_SELECTED_BITS _u(0xffffffff) |
| #define CLOCKS_CLK_GPOUT2_SELECTED_RESET _u(0x00000001) |
| #define CLOCKS_CLK_GPOUT2_SELECTED_MSB _u(31) |
| #define CLOCKS_CLK_GPOUT2_SELECTED_LSB _u(0) |
| #define CLOCKS_CLK_GPOUT2_SELECTED_ACCESS "RO" |
| // ============================================================================= |
| // Register : CLOCKS_CLK_GPOUT3_CTRL |
| // Description : Clock control, can be changed on-the-fly (except for auxsrc) |
| #define CLOCKS_CLK_GPOUT3_CTRL_OFFSET _u(0x00000024) |
| #define CLOCKS_CLK_GPOUT3_CTRL_BITS _u(0x00131de0) |
| #define CLOCKS_CLK_GPOUT3_CTRL_RESET _u(0x00000000) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT3_CTRL_NUDGE |
| // Description : An edge on this signal shifts the phase of the output by 1 |
| // cycle of the input clock |
| // This can be done at any time |
| #define CLOCKS_CLK_GPOUT3_CTRL_NUDGE_RESET _u(0x0) |
| #define CLOCKS_CLK_GPOUT3_CTRL_NUDGE_BITS _u(0x00100000) |
| #define CLOCKS_CLK_GPOUT3_CTRL_NUDGE_MSB _u(20) |
| #define CLOCKS_CLK_GPOUT3_CTRL_NUDGE_LSB _u(20) |
| #define CLOCKS_CLK_GPOUT3_CTRL_NUDGE_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT3_CTRL_PHASE |
| // Description : This delays the enable signal by up to 3 cycles of the input |
| // clock |
| // This must be set before the clock is enabled to have any effect |
| #define CLOCKS_CLK_GPOUT3_CTRL_PHASE_RESET _u(0x0) |
| #define CLOCKS_CLK_GPOUT3_CTRL_PHASE_BITS _u(0x00030000) |
| #define CLOCKS_CLK_GPOUT3_CTRL_PHASE_MSB _u(17) |
| #define CLOCKS_CLK_GPOUT3_CTRL_PHASE_LSB _u(16) |
| #define CLOCKS_CLK_GPOUT3_CTRL_PHASE_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT3_CTRL_DC50 |
| // Description : Enables duty cycle correction for odd divisors |
| #define CLOCKS_CLK_GPOUT3_CTRL_DC50_RESET _u(0x0) |
| #define CLOCKS_CLK_GPOUT3_CTRL_DC50_BITS _u(0x00001000) |
| #define CLOCKS_CLK_GPOUT3_CTRL_DC50_MSB _u(12) |
| #define CLOCKS_CLK_GPOUT3_CTRL_DC50_LSB _u(12) |
| #define CLOCKS_CLK_GPOUT3_CTRL_DC50_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT3_CTRL_ENABLE |
| // Description : Starts and stops the clock generator cleanly |
| #define CLOCKS_CLK_GPOUT3_CTRL_ENABLE_RESET _u(0x0) |
| #define CLOCKS_CLK_GPOUT3_CTRL_ENABLE_BITS _u(0x00000800) |
| #define CLOCKS_CLK_GPOUT3_CTRL_ENABLE_MSB _u(11) |
| #define CLOCKS_CLK_GPOUT3_CTRL_ENABLE_LSB _u(11) |
| #define CLOCKS_CLK_GPOUT3_CTRL_ENABLE_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT3_CTRL_KILL |
| // Description : Asynchronously kills the clock generator |
| #define CLOCKS_CLK_GPOUT3_CTRL_KILL_RESET _u(0x0) |
| #define CLOCKS_CLK_GPOUT3_CTRL_KILL_BITS _u(0x00000400) |
| #define CLOCKS_CLK_GPOUT3_CTRL_KILL_MSB _u(10) |
| #define CLOCKS_CLK_GPOUT3_CTRL_KILL_LSB _u(10) |
| #define CLOCKS_CLK_GPOUT3_CTRL_KILL_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT3_CTRL_AUXSRC |
| // Description : Selects the auxiliary clock source, will glitch when switching |
| // 0x0 -> clksrc_pll_sys |
| // 0x1 -> clksrc_gpin0 |
| // 0x2 -> clksrc_gpin1 |
| // 0x3 -> clksrc_pll_usb |
| // 0x4 -> rosc_clksrc_ph |
| // 0x5 -> xosc_clksrc |
| // 0x6 -> clk_sys |
| // 0x7 -> clk_usb |
| // 0x8 -> clk_adc |
| // 0x9 -> clk_rtc |
| // 0xa -> clk_ref |
| #define CLOCKS_CLK_GPOUT3_CTRL_AUXSRC_RESET _u(0x0) |
| #define CLOCKS_CLK_GPOUT3_CTRL_AUXSRC_BITS _u(0x000001e0) |
| #define CLOCKS_CLK_GPOUT3_CTRL_AUXSRC_MSB _u(8) |
| #define CLOCKS_CLK_GPOUT3_CTRL_AUXSRC_LSB _u(5) |
| #define CLOCKS_CLK_GPOUT3_CTRL_AUXSRC_ACCESS "RW" |
| #define CLOCKS_CLK_GPOUT3_CTRL_AUXSRC_VALUE_CLKSRC_PLL_SYS _u(0x0) |
| #define CLOCKS_CLK_GPOUT3_CTRL_AUXSRC_VALUE_CLKSRC_GPIN0 _u(0x1) |
| #define CLOCKS_CLK_GPOUT3_CTRL_AUXSRC_VALUE_CLKSRC_GPIN1 _u(0x2) |
| #define CLOCKS_CLK_GPOUT3_CTRL_AUXSRC_VALUE_CLKSRC_PLL_USB _u(0x3) |
| #define CLOCKS_CLK_GPOUT3_CTRL_AUXSRC_VALUE_ROSC_CLKSRC_PH _u(0x4) |
| #define CLOCKS_CLK_GPOUT3_CTRL_AUXSRC_VALUE_XOSC_CLKSRC _u(0x5) |
| #define CLOCKS_CLK_GPOUT3_CTRL_AUXSRC_VALUE_CLK_SYS _u(0x6) |
| #define CLOCKS_CLK_GPOUT3_CTRL_AUXSRC_VALUE_CLK_USB _u(0x7) |
| #define CLOCKS_CLK_GPOUT3_CTRL_AUXSRC_VALUE_CLK_ADC _u(0x8) |
| #define CLOCKS_CLK_GPOUT3_CTRL_AUXSRC_VALUE_CLK_RTC _u(0x9) |
| #define CLOCKS_CLK_GPOUT3_CTRL_AUXSRC_VALUE_CLK_REF _u(0xa) |
| // ============================================================================= |
| // Register : CLOCKS_CLK_GPOUT3_DIV |
| // Description : Clock divisor, can be changed on-the-fly |
| #define CLOCKS_CLK_GPOUT3_DIV_OFFSET _u(0x00000028) |
| #define CLOCKS_CLK_GPOUT3_DIV_BITS _u(0xffffffff) |
| #define CLOCKS_CLK_GPOUT3_DIV_RESET _u(0x00000100) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT3_DIV_INT |
| // Description : Integer component of the divisor, 0 -> divide by 2^16 |
| #define CLOCKS_CLK_GPOUT3_DIV_INT_RESET _u(0x000001) |
| #define CLOCKS_CLK_GPOUT3_DIV_INT_BITS _u(0xffffff00) |
| #define CLOCKS_CLK_GPOUT3_DIV_INT_MSB _u(31) |
| #define CLOCKS_CLK_GPOUT3_DIV_INT_LSB _u(8) |
| #define CLOCKS_CLK_GPOUT3_DIV_INT_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_GPOUT3_DIV_FRAC |
| // Description : Fractional component of the divisor |
| #define CLOCKS_CLK_GPOUT3_DIV_FRAC_RESET _u(0x00) |
| #define CLOCKS_CLK_GPOUT3_DIV_FRAC_BITS _u(0x000000ff) |
| #define CLOCKS_CLK_GPOUT3_DIV_FRAC_MSB _u(7) |
| #define CLOCKS_CLK_GPOUT3_DIV_FRAC_LSB _u(0) |
| #define CLOCKS_CLK_GPOUT3_DIV_FRAC_ACCESS "RW" |
| // ============================================================================= |
| // Register : CLOCKS_CLK_GPOUT3_SELECTED |
| // Description : Indicates which SRC is currently selected by the glitchless mux |
| // (one-hot). |
| // This slice does not have a glitchless mux (only the AUX_SRC |
| // field is present, not SRC) so this register is hardwired to |
| // 0x1. |
| #define CLOCKS_CLK_GPOUT3_SELECTED_OFFSET _u(0x0000002c) |
| #define CLOCKS_CLK_GPOUT3_SELECTED_BITS _u(0xffffffff) |
| #define CLOCKS_CLK_GPOUT3_SELECTED_RESET _u(0x00000001) |
| #define CLOCKS_CLK_GPOUT3_SELECTED_MSB _u(31) |
| #define CLOCKS_CLK_GPOUT3_SELECTED_LSB _u(0) |
| #define CLOCKS_CLK_GPOUT3_SELECTED_ACCESS "RO" |
| // ============================================================================= |
| // Register : CLOCKS_CLK_REF_CTRL |
| // Description : Clock control, can be changed on-the-fly (except for auxsrc) |
| #define CLOCKS_CLK_REF_CTRL_OFFSET _u(0x00000030) |
| #define CLOCKS_CLK_REF_CTRL_BITS _u(0x00000063) |
| #define CLOCKS_CLK_REF_CTRL_RESET _u(0x00000000) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_REF_CTRL_AUXSRC |
| // Description : Selects the auxiliary clock source, will glitch when switching |
| // 0x0 -> clksrc_pll_usb |
| // 0x1 -> clksrc_gpin0 |
| // 0x2 -> clksrc_gpin1 |
| #define CLOCKS_CLK_REF_CTRL_AUXSRC_RESET _u(0x0) |
| #define CLOCKS_CLK_REF_CTRL_AUXSRC_BITS _u(0x00000060) |
| #define CLOCKS_CLK_REF_CTRL_AUXSRC_MSB _u(6) |
| #define CLOCKS_CLK_REF_CTRL_AUXSRC_LSB _u(5) |
| #define CLOCKS_CLK_REF_CTRL_AUXSRC_ACCESS "RW" |
| #define CLOCKS_CLK_REF_CTRL_AUXSRC_VALUE_CLKSRC_PLL_USB _u(0x0) |
| #define CLOCKS_CLK_REF_CTRL_AUXSRC_VALUE_CLKSRC_GPIN0 _u(0x1) |
| #define CLOCKS_CLK_REF_CTRL_AUXSRC_VALUE_CLKSRC_GPIN1 _u(0x2) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_REF_CTRL_SRC |
| // Description : Selects the clock source glitchlessly, can be changed |
| // on-the-fly |
| // 0x0 -> rosc_clksrc_ph |
| // 0x1 -> clksrc_clk_ref_aux |
| // 0x2 -> xosc_clksrc |
| #define CLOCKS_CLK_REF_CTRL_SRC_RESET "-" |
| #define CLOCKS_CLK_REF_CTRL_SRC_BITS _u(0x00000003) |
| #define CLOCKS_CLK_REF_CTRL_SRC_MSB _u(1) |
| #define CLOCKS_CLK_REF_CTRL_SRC_LSB _u(0) |
| #define CLOCKS_CLK_REF_CTRL_SRC_ACCESS "RW" |
| #define CLOCKS_CLK_REF_CTRL_SRC_VALUE_ROSC_CLKSRC_PH _u(0x0) |
| #define CLOCKS_CLK_REF_CTRL_SRC_VALUE_CLKSRC_CLK_REF_AUX _u(0x1) |
| #define CLOCKS_CLK_REF_CTRL_SRC_VALUE_XOSC_CLKSRC _u(0x2) |
| // ============================================================================= |
| // Register : CLOCKS_CLK_REF_DIV |
| // Description : Clock divisor, can be changed on-the-fly |
| #define CLOCKS_CLK_REF_DIV_OFFSET _u(0x00000034) |
| #define CLOCKS_CLK_REF_DIV_BITS _u(0x00000300) |
| #define CLOCKS_CLK_REF_DIV_RESET _u(0x00000100) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_REF_DIV_INT |
| // Description : Integer component of the divisor, 0 -> divide by 2^16 |
| #define CLOCKS_CLK_REF_DIV_INT_RESET _u(0x1) |
| #define CLOCKS_CLK_REF_DIV_INT_BITS _u(0x00000300) |
| #define CLOCKS_CLK_REF_DIV_INT_MSB _u(9) |
| #define CLOCKS_CLK_REF_DIV_INT_LSB _u(8) |
| #define CLOCKS_CLK_REF_DIV_INT_ACCESS "RW" |
| // ============================================================================= |
| // Register : CLOCKS_CLK_REF_SELECTED |
| // Description : Indicates which SRC is currently selected by the glitchless mux |
| // (one-hot). |
| // The glitchless multiplexer does not switch instantaneously (to |
| // avoid glitches), so software should poll this register to wait |
| // for the switch to complete. This register contains one decoded |
| // bit for each of the clock sources enumerated in the CTRL SRC |
| // field. At most one of these bits will be set at any time, |
| // indicating that clock is currently present at the output of the |
| // glitchless mux. Whilst switching is in progress, this register |
| // may briefly show all-0s. |
| #define CLOCKS_CLK_REF_SELECTED_OFFSET _u(0x00000038) |
| #define CLOCKS_CLK_REF_SELECTED_BITS _u(0xffffffff) |
| #define CLOCKS_CLK_REF_SELECTED_RESET _u(0x00000001) |
| #define CLOCKS_CLK_REF_SELECTED_MSB _u(31) |
| #define CLOCKS_CLK_REF_SELECTED_LSB _u(0) |
| #define CLOCKS_CLK_REF_SELECTED_ACCESS "RO" |
| // ============================================================================= |
| // Register : CLOCKS_CLK_SYS_CTRL |
| // Description : Clock control, can be changed on-the-fly (except for auxsrc) |
| #define CLOCKS_CLK_SYS_CTRL_OFFSET _u(0x0000003c) |
| #define CLOCKS_CLK_SYS_CTRL_BITS _u(0x000000e1) |
| #define CLOCKS_CLK_SYS_CTRL_RESET _u(0x00000000) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_SYS_CTRL_AUXSRC |
| // Description : Selects the auxiliary clock source, will glitch when switching |
| // 0x0 -> clksrc_pll_sys |
| // 0x1 -> clksrc_pll_usb |
| // 0x2 -> rosc_clksrc |
| // 0x3 -> xosc_clksrc |
| // 0x4 -> clksrc_gpin0 |
| // 0x5 -> clksrc_gpin1 |
| #define CLOCKS_CLK_SYS_CTRL_AUXSRC_RESET _u(0x0) |
| #define CLOCKS_CLK_SYS_CTRL_AUXSRC_BITS _u(0x000000e0) |
| #define CLOCKS_CLK_SYS_CTRL_AUXSRC_MSB _u(7) |
| #define CLOCKS_CLK_SYS_CTRL_AUXSRC_LSB _u(5) |
| #define CLOCKS_CLK_SYS_CTRL_AUXSRC_ACCESS "RW" |
| #define CLOCKS_CLK_SYS_CTRL_AUXSRC_VALUE_CLKSRC_PLL_SYS _u(0x0) |
| #define CLOCKS_CLK_SYS_CTRL_AUXSRC_VALUE_CLKSRC_PLL_USB _u(0x1) |
| #define CLOCKS_CLK_SYS_CTRL_AUXSRC_VALUE_ROSC_CLKSRC _u(0x2) |
| #define CLOCKS_CLK_SYS_CTRL_AUXSRC_VALUE_XOSC_CLKSRC _u(0x3) |
| #define CLOCKS_CLK_SYS_CTRL_AUXSRC_VALUE_CLKSRC_GPIN0 _u(0x4) |
| #define CLOCKS_CLK_SYS_CTRL_AUXSRC_VALUE_CLKSRC_GPIN1 _u(0x5) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_SYS_CTRL_SRC |
| // Description : Selects the clock source glitchlessly, can be changed |
| // on-the-fly |
| // 0x0 -> clk_ref |
| // 0x1 -> clksrc_clk_sys_aux |
| #define CLOCKS_CLK_SYS_CTRL_SRC_RESET _u(0x0) |
| #define CLOCKS_CLK_SYS_CTRL_SRC_BITS _u(0x00000001) |
| #define CLOCKS_CLK_SYS_CTRL_SRC_MSB _u(0) |
| #define CLOCKS_CLK_SYS_CTRL_SRC_LSB _u(0) |
| #define CLOCKS_CLK_SYS_CTRL_SRC_ACCESS "RW" |
| #define CLOCKS_CLK_SYS_CTRL_SRC_VALUE_CLK_REF _u(0x0) |
| #define CLOCKS_CLK_SYS_CTRL_SRC_VALUE_CLKSRC_CLK_SYS_AUX _u(0x1) |
| // ============================================================================= |
| // Register : CLOCKS_CLK_SYS_DIV |
| // Description : Clock divisor, can be changed on-the-fly |
| #define CLOCKS_CLK_SYS_DIV_OFFSET _u(0x00000040) |
| #define CLOCKS_CLK_SYS_DIV_BITS _u(0xffffffff) |
| #define CLOCKS_CLK_SYS_DIV_RESET _u(0x00000100) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_SYS_DIV_INT |
| // Description : Integer component of the divisor, 0 -> divide by 2^16 |
| #define CLOCKS_CLK_SYS_DIV_INT_RESET _u(0x000001) |
| #define CLOCKS_CLK_SYS_DIV_INT_BITS _u(0xffffff00) |
| #define CLOCKS_CLK_SYS_DIV_INT_MSB _u(31) |
| #define CLOCKS_CLK_SYS_DIV_INT_LSB _u(8) |
| #define CLOCKS_CLK_SYS_DIV_INT_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_SYS_DIV_FRAC |
| // Description : Fractional component of the divisor |
| #define CLOCKS_CLK_SYS_DIV_FRAC_RESET _u(0x00) |
| #define CLOCKS_CLK_SYS_DIV_FRAC_BITS _u(0x000000ff) |
| #define CLOCKS_CLK_SYS_DIV_FRAC_MSB _u(7) |
| #define CLOCKS_CLK_SYS_DIV_FRAC_LSB _u(0) |
| #define CLOCKS_CLK_SYS_DIV_FRAC_ACCESS "RW" |
| // ============================================================================= |
| // Register : CLOCKS_CLK_SYS_SELECTED |
| // Description : Indicates which SRC is currently selected by the glitchless mux |
| // (one-hot). |
| // The glitchless multiplexer does not switch instantaneously (to |
| // avoid glitches), so software should poll this register to wait |
| // for the switch to complete. This register contains one decoded |
| // bit for each of the clock sources enumerated in the CTRL SRC |
| // field. At most one of these bits will be set at any time, |
| // indicating that clock is currently present at the output of the |
| // glitchless mux. Whilst switching is in progress, this register |
| // may briefly show all-0s. |
| #define CLOCKS_CLK_SYS_SELECTED_OFFSET _u(0x00000044) |
| #define CLOCKS_CLK_SYS_SELECTED_BITS _u(0xffffffff) |
| #define CLOCKS_CLK_SYS_SELECTED_RESET _u(0x00000001) |
| #define CLOCKS_CLK_SYS_SELECTED_MSB _u(31) |
| #define CLOCKS_CLK_SYS_SELECTED_LSB _u(0) |
| #define CLOCKS_CLK_SYS_SELECTED_ACCESS "RO" |
| // ============================================================================= |
| // Register : CLOCKS_CLK_PERI_CTRL |
| // Description : Clock control, can be changed on-the-fly (except for auxsrc) |
| #define CLOCKS_CLK_PERI_CTRL_OFFSET _u(0x00000048) |
| #define CLOCKS_CLK_PERI_CTRL_BITS _u(0x00000ce0) |
| #define CLOCKS_CLK_PERI_CTRL_RESET _u(0x00000000) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_PERI_CTRL_ENABLE |
| // Description : Starts and stops the clock generator cleanly |
| #define CLOCKS_CLK_PERI_CTRL_ENABLE_RESET _u(0x0) |
| #define CLOCKS_CLK_PERI_CTRL_ENABLE_BITS _u(0x00000800) |
| #define CLOCKS_CLK_PERI_CTRL_ENABLE_MSB _u(11) |
| #define CLOCKS_CLK_PERI_CTRL_ENABLE_LSB _u(11) |
| #define CLOCKS_CLK_PERI_CTRL_ENABLE_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_PERI_CTRL_KILL |
| // Description : Asynchronously kills the clock generator |
| #define CLOCKS_CLK_PERI_CTRL_KILL_RESET _u(0x0) |
| #define CLOCKS_CLK_PERI_CTRL_KILL_BITS _u(0x00000400) |
| #define CLOCKS_CLK_PERI_CTRL_KILL_MSB _u(10) |
| #define CLOCKS_CLK_PERI_CTRL_KILL_LSB _u(10) |
| #define CLOCKS_CLK_PERI_CTRL_KILL_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_PERI_CTRL_AUXSRC |
| // Description : Selects the auxiliary clock source, will glitch when switching |
| // 0x0 -> clk_sys |
| // 0x1 -> clksrc_pll_sys |
| // 0x2 -> clksrc_pll_usb |
| // 0x3 -> rosc_clksrc_ph |
| // 0x4 -> xosc_clksrc |
| // 0x5 -> clksrc_gpin0 |
| // 0x6 -> clksrc_gpin1 |
| #define CLOCKS_CLK_PERI_CTRL_AUXSRC_RESET _u(0x0) |
| #define CLOCKS_CLK_PERI_CTRL_AUXSRC_BITS _u(0x000000e0) |
| #define CLOCKS_CLK_PERI_CTRL_AUXSRC_MSB _u(7) |
| #define CLOCKS_CLK_PERI_CTRL_AUXSRC_LSB _u(5) |
| #define CLOCKS_CLK_PERI_CTRL_AUXSRC_ACCESS "RW" |
| #define CLOCKS_CLK_PERI_CTRL_AUXSRC_VALUE_CLK_SYS _u(0x0) |
| #define CLOCKS_CLK_PERI_CTRL_AUXSRC_VALUE_CLKSRC_PLL_SYS _u(0x1) |
| #define CLOCKS_CLK_PERI_CTRL_AUXSRC_VALUE_CLKSRC_PLL_USB _u(0x2) |
| #define CLOCKS_CLK_PERI_CTRL_AUXSRC_VALUE_ROSC_CLKSRC_PH _u(0x3) |
| #define CLOCKS_CLK_PERI_CTRL_AUXSRC_VALUE_XOSC_CLKSRC _u(0x4) |
| #define CLOCKS_CLK_PERI_CTRL_AUXSRC_VALUE_CLKSRC_GPIN0 _u(0x5) |
| #define CLOCKS_CLK_PERI_CTRL_AUXSRC_VALUE_CLKSRC_GPIN1 _u(0x6) |
| // ============================================================================= |
| // Register : CLOCKS_CLK_PERI_SELECTED |
| // Description : Indicates which SRC is currently selected by the glitchless mux |
| // (one-hot). |
| // This slice does not have a glitchless mux (only the AUX_SRC |
| // field is present, not SRC) so this register is hardwired to |
| // 0x1. |
| #define CLOCKS_CLK_PERI_SELECTED_OFFSET _u(0x00000050) |
| #define CLOCKS_CLK_PERI_SELECTED_BITS _u(0xffffffff) |
| #define CLOCKS_CLK_PERI_SELECTED_RESET _u(0x00000001) |
| #define CLOCKS_CLK_PERI_SELECTED_MSB _u(31) |
| #define CLOCKS_CLK_PERI_SELECTED_LSB _u(0) |
| #define CLOCKS_CLK_PERI_SELECTED_ACCESS "RO" |
| // ============================================================================= |
| // Register : CLOCKS_CLK_USB_CTRL |
| // Description : Clock control, can be changed on-the-fly (except for auxsrc) |
| #define CLOCKS_CLK_USB_CTRL_OFFSET _u(0x00000054) |
| #define CLOCKS_CLK_USB_CTRL_BITS _u(0x00130ce0) |
| #define CLOCKS_CLK_USB_CTRL_RESET _u(0x00000000) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_USB_CTRL_NUDGE |
| // Description : An edge on this signal shifts the phase of the output by 1 |
| // cycle of the input clock |
| // This can be done at any time |
| #define CLOCKS_CLK_USB_CTRL_NUDGE_RESET _u(0x0) |
| #define CLOCKS_CLK_USB_CTRL_NUDGE_BITS _u(0x00100000) |
| #define CLOCKS_CLK_USB_CTRL_NUDGE_MSB _u(20) |
| #define CLOCKS_CLK_USB_CTRL_NUDGE_LSB _u(20) |
| #define CLOCKS_CLK_USB_CTRL_NUDGE_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_USB_CTRL_PHASE |
| // Description : This delays the enable signal by up to 3 cycles of the input |
| // clock |
| // This must be set before the clock is enabled to have any effect |
| #define CLOCKS_CLK_USB_CTRL_PHASE_RESET _u(0x0) |
| #define CLOCKS_CLK_USB_CTRL_PHASE_BITS _u(0x00030000) |
| #define CLOCKS_CLK_USB_CTRL_PHASE_MSB _u(17) |
| #define CLOCKS_CLK_USB_CTRL_PHASE_LSB _u(16) |
| #define CLOCKS_CLK_USB_CTRL_PHASE_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_USB_CTRL_ENABLE |
| // Description : Starts and stops the clock generator cleanly |
| #define CLOCKS_CLK_USB_CTRL_ENABLE_RESET _u(0x0) |
| #define CLOCKS_CLK_USB_CTRL_ENABLE_BITS _u(0x00000800) |
| #define CLOCKS_CLK_USB_CTRL_ENABLE_MSB _u(11) |
| #define CLOCKS_CLK_USB_CTRL_ENABLE_LSB _u(11) |
| #define CLOCKS_CLK_USB_CTRL_ENABLE_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_USB_CTRL_KILL |
| // Description : Asynchronously kills the clock generator |
| #define CLOCKS_CLK_USB_CTRL_KILL_RESET _u(0x0) |
| #define CLOCKS_CLK_USB_CTRL_KILL_BITS _u(0x00000400) |
| #define CLOCKS_CLK_USB_CTRL_KILL_MSB _u(10) |
| #define CLOCKS_CLK_USB_CTRL_KILL_LSB _u(10) |
| #define CLOCKS_CLK_USB_CTRL_KILL_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_USB_CTRL_AUXSRC |
| // Description : Selects the auxiliary clock source, will glitch when switching |
| // 0x0 -> clksrc_pll_usb |
| // 0x1 -> clksrc_pll_sys |
| // 0x2 -> rosc_clksrc_ph |
| // 0x3 -> xosc_clksrc |
| // 0x4 -> clksrc_gpin0 |
| // 0x5 -> clksrc_gpin1 |
| #define CLOCKS_CLK_USB_CTRL_AUXSRC_RESET _u(0x0) |
| #define CLOCKS_CLK_USB_CTRL_AUXSRC_BITS _u(0x000000e0) |
| #define CLOCKS_CLK_USB_CTRL_AUXSRC_MSB _u(7) |
| #define CLOCKS_CLK_USB_CTRL_AUXSRC_LSB _u(5) |
| #define CLOCKS_CLK_USB_CTRL_AUXSRC_ACCESS "RW" |
| #define CLOCKS_CLK_USB_CTRL_AUXSRC_VALUE_CLKSRC_PLL_USB _u(0x0) |
| #define CLOCKS_CLK_USB_CTRL_AUXSRC_VALUE_CLKSRC_PLL_SYS _u(0x1) |
| #define CLOCKS_CLK_USB_CTRL_AUXSRC_VALUE_ROSC_CLKSRC_PH _u(0x2) |
| #define CLOCKS_CLK_USB_CTRL_AUXSRC_VALUE_XOSC_CLKSRC _u(0x3) |
| #define CLOCKS_CLK_USB_CTRL_AUXSRC_VALUE_CLKSRC_GPIN0 _u(0x4) |
| #define CLOCKS_CLK_USB_CTRL_AUXSRC_VALUE_CLKSRC_GPIN1 _u(0x5) |
| // ============================================================================= |
| // Register : CLOCKS_CLK_USB_DIV |
| // Description : Clock divisor, can be changed on-the-fly |
| #define CLOCKS_CLK_USB_DIV_OFFSET _u(0x00000058) |
| #define CLOCKS_CLK_USB_DIV_BITS _u(0x00000300) |
| #define CLOCKS_CLK_USB_DIV_RESET _u(0x00000100) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_USB_DIV_INT |
| // Description : Integer component of the divisor, 0 -> divide by 2^16 |
| #define CLOCKS_CLK_USB_DIV_INT_RESET _u(0x1) |
| #define CLOCKS_CLK_USB_DIV_INT_BITS _u(0x00000300) |
| #define CLOCKS_CLK_USB_DIV_INT_MSB _u(9) |
| #define CLOCKS_CLK_USB_DIV_INT_LSB _u(8) |
| #define CLOCKS_CLK_USB_DIV_INT_ACCESS "RW" |
| // ============================================================================= |
| // Register : CLOCKS_CLK_USB_SELECTED |
| // Description : Indicates which SRC is currently selected by the glitchless mux |
| // (one-hot). |
| // This slice does not have a glitchless mux (only the AUX_SRC |
| // field is present, not SRC) so this register is hardwired to |
| // 0x1. |
| #define CLOCKS_CLK_USB_SELECTED_OFFSET _u(0x0000005c) |
| #define CLOCKS_CLK_USB_SELECTED_BITS _u(0xffffffff) |
| #define CLOCKS_CLK_USB_SELECTED_RESET _u(0x00000001) |
| #define CLOCKS_CLK_USB_SELECTED_MSB _u(31) |
| #define CLOCKS_CLK_USB_SELECTED_LSB _u(0) |
| #define CLOCKS_CLK_USB_SELECTED_ACCESS "RO" |
| // ============================================================================= |
| // Register : CLOCKS_CLK_ADC_CTRL |
| // Description : Clock control, can be changed on-the-fly (except for auxsrc) |
| #define CLOCKS_CLK_ADC_CTRL_OFFSET _u(0x00000060) |
| #define CLOCKS_CLK_ADC_CTRL_BITS _u(0x00130ce0) |
| #define CLOCKS_CLK_ADC_CTRL_RESET _u(0x00000000) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_ADC_CTRL_NUDGE |
| // Description : An edge on this signal shifts the phase of the output by 1 |
| // cycle of the input clock |
| // This can be done at any time |
| #define CLOCKS_CLK_ADC_CTRL_NUDGE_RESET _u(0x0) |
| #define CLOCKS_CLK_ADC_CTRL_NUDGE_BITS _u(0x00100000) |
| #define CLOCKS_CLK_ADC_CTRL_NUDGE_MSB _u(20) |
| #define CLOCKS_CLK_ADC_CTRL_NUDGE_LSB _u(20) |
| #define CLOCKS_CLK_ADC_CTRL_NUDGE_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_ADC_CTRL_PHASE |
| // Description : This delays the enable signal by up to 3 cycles of the input |
| // clock |
| // This must be set before the clock is enabled to have any effect |
| #define CLOCKS_CLK_ADC_CTRL_PHASE_RESET _u(0x0) |
| #define CLOCKS_CLK_ADC_CTRL_PHASE_BITS _u(0x00030000) |
| #define CLOCKS_CLK_ADC_CTRL_PHASE_MSB _u(17) |
| #define CLOCKS_CLK_ADC_CTRL_PHASE_LSB _u(16) |
| #define CLOCKS_CLK_ADC_CTRL_PHASE_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_ADC_CTRL_ENABLE |
| // Description : Starts and stops the clock generator cleanly |
| #define CLOCKS_CLK_ADC_CTRL_ENABLE_RESET _u(0x0) |
| #define CLOCKS_CLK_ADC_CTRL_ENABLE_BITS _u(0x00000800) |
| #define CLOCKS_CLK_ADC_CTRL_ENABLE_MSB _u(11) |
| #define CLOCKS_CLK_ADC_CTRL_ENABLE_LSB _u(11) |
| #define CLOCKS_CLK_ADC_CTRL_ENABLE_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_ADC_CTRL_KILL |
| // Description : Asynchronously kills the clock generator |
| #define CLOCKS_CLK_ADC_CTRL_KILL_RESET _u(0x0) |
| #define CLOCKS_CLK_ADC_CTRL_KILL_BITS _u(0x00000400) |
| #define CLOCKS_CLK_ADC_CTRL_KILL_MSB _u(10) |
| #define CLOCKS_CLK_ADC_CTRL_KILL_LSB _u(10) |
| #define CLOCKS_CLK_ADC_CTRL_KILL_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_ADC_CTRL_AUXSRC |
| // Description : Selects the auxiliary clock source, will glitch when switching |
| // 0x0 -> clksrc_pll_usb |
| // 0x1 -> clksrc_pll_sys |
| // 0x2 -> rosc_clksrc_ph |
| // 0x3 -> xosc_clksrc |
| // 0x4 -> clksrc_gpin0 |
| // 0x5 -> clksrc_gpin1 |
| #define CLOCKS_CLK_ADC_CTRL_AUXSRC_RESET _u(0x0) |
| #define CLOCKS_CLK_ADC_CTRL_AUXSRC_BITS _u(0x000000e0) |
| #define CLOCKS_CLK_ADC_CTRL_AUXSRC_MSB _u(7) |
| #define CLOCKS_CLK_ADC_CTRL_AUXSRC_LSB _u(5) |
| #define CLOCKS_CLK_ADC_CTRL_AUXSRC_ACCESS "RW" |
| #define CLOCKS_CLK_ADC_CTRL_AUXSRC_VALUE_CLKSRC_PLL_USB _u(0x0) |
| #define CLOCKS_CLK_ADC_CTRL_AUXSRC_VALUE_CLKSRC_PLL_SYS _u(0x1) |
| #define CLOCKS_CLK_ADC_CTRL_AUXSRC_VALUE_ROSC_CLKSRC_PH _u(0x2) |
| #define CLOCKS_CLK_ADC_CTRL_AUXSRC_VALUE_XOSC_CLKSRC _u(0x3) |
| #define CLOCKS_CLK_ADC_CTRL_AUXSRC_VALUE_CLKSRC_GPIN0 _u(0x4) |
| #define CLOCKS_CLK_ADC_CTRL_AUXSRC_VALUE_CLKSRC_GPIN1 _u(0x5) |
| // ============================================================================= |
| // Register : CLOCKS_CLK_ADC_DIV |
| // Description : Clock divisor, can be changed on-the-fly |
| #define CLOCKS_CLK_ADC_DIV_OFFSET _u(0x00000064) |
| #define CLOCKS_CLK_ADC_DIV_BITS _u(0x00000300) |
| #define CLOCKS_CLK_ADC_DIV_RESET _u(0x00000100) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_ADC_DIV_INT |
| // Description : Integer component of the divisor, 0 -> divide by 2^16 |
| #define CLOCKS_CLK_ADC_DIV_INT_RESET _u(0x1) |
| #define CLOCKS_CLK_ADC_DIV_INT_BITS _u(0x00000300) |
| #define CLOCKS_CLK_ADC_DIV_INT_MSB _u(9) |
| #define CLOCKS_CLK_ADC_DIV_INT_LSB _u(8) |
| #define CLOCKS_CLK_ADC_DIV_INT_ACCESS "RW" |
| // ============================================================================= |
| // Register : CLOCKS_CLK_ADC_SELECTED |
| // Description : Indicates which SRC is currently selected by the glitchless mux |
| // (one-hot). |
| // This slice does not have a glitchless mux (only the AUX_SRC |
| // field is present, not SRC) so this register is hardwired to |
| // 0x1. |
| #define CLOCKS_CLK_ADC_SELECTED_OFFSET _u(0x00000068) |
| #define CLOCKS_CLK_ADC_SELECTED_BITS _u(0xffffffff) |
| #define CLOCKS_CLK_ADC_SELECTED_RESET _u(0x00000001) |
| #define CLOCKS_CLK_ADC_SELECTED_MSB _u(31) |
| #define CLOCKS_CLK_ADC_SELECTED_LSB _u(0) |
| #define CLOCKS_CLK_ADC_SELECTED_ACCESS "RO" |
| // ============================================================================= |
| // Register : CLOCKS_CLK_RTC_CTRL |
| // Description : Clock control, can be changed on-the-fly (except for auxsrc) |
| #define CLOCKS_CLK_RTC_CTRL_OFFSET _u(0x0000006c) |
| #define CLOCKS_CLK_RTC_CTRL_BITS _u(0x00130ce0) |
| #define CLOCKS_CLK_RTC_CTRL_RESET _u(0x00000000) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_RTC_CTRL_NUDGE |
| // Description : An edge on this signal shifts the phase of the output by 1 |
| // cycle of the input clock |
| // This can be done at any time |
| #define CLOCKS_CLK_RTC_CTRL_NUDGE_RESET _u(0x0) |
| #define CLOCKS_CLK_RTC_CTRL_NUDGE_BITS _u(0x00100000) |
| #define CLOCKS_CLK_RTC_CTRL_NUDGE_MSB _u(20) |
| #define CLOCKS_CLK_RTC_CTRL_NUDGE_LSB _u(20) |
| #define CLOCKS_CLK_RTC_CTRL_NUDGE_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_RTC_CTRL_PHASE |
| // Description : This delays the enable signal by up to 3 cycles of the input |
| // clock |
| // This must be set before the clock is enabled to have any effect |
| #define CLOCKS_CLK_RTC_CTRL_PHASE_RESET _u(0x0) |
| #define CLOCKS_CLK_RTC_CTRL_PHASE_BITS _u(0x00030000) |
| #define CLOCKS_CLK_RTC_CTRL_PHASE_MSB _u(17) |
| #define CLOCKS_CLK_RTC_CTRL_PHASE_LSB _u(16) |
| #define CLOCKS_CLK_RTC_CTRL_PHASE_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_RTC_CTRL_ENABLE |
| // Description : Starts and stops the clock generator cleanly |
| #define CLOCKS_CLK_RTC_CTRL_ENABLE_RESET _u(0x0) |
| #define CLOCKS_CLK_RTC_CTRL_ENABLE_BITS _u(0x00000800) |
| #define CLOCKS_CLK_RTC_CTRL_ENABLE_MSB _u(11) |
| #define CLOCKS_CLK_RTC_CTRL_ENABLE_LSB _u(11) |
| #define CLOCKS_CLK_RTC_CTRL_ENABLE_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_RTC_CTRL_KILL |
| // Description : Asynchronously kills the clock generator |
| #define CLOCKS_CLK_RTC_CTRL_KILL_RESET _u(0x0) |
| #define CLOCKS_CLK_RTC_CTRL_KILL_BITS _u(0x00000400) |
| #define CLOCKS_CLK_RTC_CTRL_KILL_MSB _u(10) |
| #define CLOCKS_CLK_RTC_CTRL_KILL_LSB _u(10) |
| #define CLOCKS_CLK_RTC_CTRL_KILL_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_RTC_CTRL_AUXSRC |
| // Description : Selects the auxiliary clock source, will glitch when switching |
| // 0x0 -> clksrc_pll_usb |
| // 0x1 -> clksrc_pll_sys |
| // 0x2 -> rosc_clksrc_ph |
| // 0x3 -> xosc_clksrc |
| // 0x4 -> clksrc_gpin0 |
| // 0x5 -> clksrc_gpin1 |
| #define CLOCKS_CLK_RTC_CTRL_AUXSRC_RESET _u(0x0) |
| #define CLOCKS_CLK_RTC_CTRL_AUXSRC_BITS _u(0x000000e0) |
| #define CLOCKS_CLK_RTC_CTRL_AUXSRC_MSB _u(7) |
| #define CLOCKS_CLK_RTC_CTRL_AUXSRC_LSB _u(5) |
| #define CLOCKS_CLK_RTC_CTRL_AUXSRC_ACCESS "RW" |
| #define CLOCKS_CLK_RTC_CTRL_AUXSRC_VALUE_CLKSRC_PLL_USB _u(0x0) |
| #define CLOCKS_CLK_RTC_CTRL_AUXSRC_VALUE_CLKSRC_PLL_SYS _u(0x1) |
| #define CLOCKS_CLK_RTC_CTRL_AUXSRC_VALUE_ROSC_CLKSRC_PH _u(0x2) |
| #define CLOCKS_CLK_RTC_CTRL_AUXSRC_VALUE_XOSC_CLKSRC _u(0x3) |
| #define CLOCKS_CLK_RTC_CTRL_AUXSRC_VALUE_CLKSRC_GPIN0 _u(0x4) |
| #define CLOCKS_CLK_RTC_CTRL_AUXSRC_VALUE_CLKSRC_GPIN1 _u(0x5) |
| // ============================================================================= |
| // Register : CLOCKS_CLK_RTC_DIV |
| // Description : Clock divisor, can be changed on-the-fly |
| #define CLOCKS_CLK_RTC_DIV_OFFSET _u(0x00000070) |
| #define CLOCKS_CLK_RTC_DIV_BITS _u(0xffffffff) |
| #define CLOCKS_CLK_RTC_DIV_RESET _u(0x00000100) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_RTC_DIV_INT |
| // Description : Integer component of the divisor, 0 -> divide by 2^16 |
| #define CLOCKS_CLK_RTC_DIV_INT_RESET _u(0x000001) |
| #define CLOCKS_CLK_RTC_DIV_INT_BITS _u(0xffffff00) |
| #define CLOCKS_CLK_RTC_DIV_INT_MSB _u(31) |
| #define CLOCKS_CLK_RTC_DIV_INT_LSB _u(8) |
| #define CLOCKS_CLK_RTC_DIV_INT_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_RTC_DIV_FRAC |
| // Description : Fractional component of the divisor |
| #define CLOCKS_CLK_RTC_DIV_FRAC_RESET _u(0x00) |
| #define CLOCKS_CLK_RTC_DIV_FRAC_BITS _u(0x000000ff) |
| #define CLOCKS_CLK_RTC_DIV_FRAC_MSB _u(7) |
| #define CLOCKS_CLK_RTC_DIV_FRAC_LSB _u(0) |
| #define CLOCKS_CLK_RTC_DIV_FRAC_ACCESS "RW" |
| // ============================================================================= |
| // Register : CLOCKS_CLK_RTC_SELECTED |
| // Description : Indicates which SRC is currently selected by the glitchless mux |
| // (one-hot). |
| // This slice does not have a glitchless mux (only the AUX_SRC |
| // field is present, not SRC) so this register is hardwired to |
| // 0x1. |
| #define CLOCKS_CLK_RTC_SELECTED_OFFSET _u(0x00000074) |
| #define CLOCKS_CLK_RTC_SELECTED_BITS _u(0xffffffff) |
| #define CLOCKS_CLK_RTC_SELECTED_RESET _u(0x00000001) |
| #define CLOCKS_CLK_RTC_SELECTED_MSB _u(31) |
| #define CLOCKS_CLK_RTC_SELECTED_LSB _u(0) |
| #define CLOCKS_CLK_RTC_SELECTED_ACCESS "RO" |
| // ============================================================================= |
| // Register : CLOCKS_CLK_SYS_RESUS_CTRL |
| // Description : None |
| #define CLOCKS_CLK_SYS_RESUS_CTRL_OFFSET _u(0x00000078) |
| #define CLOCKS_CLK_SYS_RESUS_CTRL_BITS _u(0x000111ff) |
| #define CLOCKS_CLK_SYS_RESUS_CTRL_RESET _u(0x000000ff) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_SYS_RESUS_CTRL_CLEAR |
| // Description : For clearing the resus after the fault that triggered it has |
| // been corrected |
| #define CLOCKS_CLK_SYS_RESUS_CTRL_CLEAR_RESET _u(0x0) |
| #define CLOCKS_CLK_SYS_RESUS_CTRL_CLEAR_BITS _u(0x00010000) |
| #define CLOCKS_CLK_SYS_RESUS_CTRL_CLEAR_MSB _u(16) |
| #define CLOCKS_CLK_SYS_RESUS_CTRL_CLEAR_LSB _u(16) |
| #define CLOCKS_CLK_SYS_RESUS_CTRL_CLEAR_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_SYS_RESUS_CTRL_FRCE |
| // Description : Force a resus, for test purposes only |
| #define CLOCKS_CLK_SYS_RESUS_CTRL_FRCE_RESET _u(0x0) |
| #define CLOCKS_CLK_SYS_RESUS_CTRL_FRCE_BITS _u(0x00001000) |
| #define CLOCKS_CLK_SYS_RESUS_CTRL_FRCE_MSB _u(12) |
| #define CLOCKS_CLK_SYS_RESUS_CTRL_FRCE_LSB _u(12) |
| #define CLOCKS_CLK_SYS_RESUS_CTRL_FRCE_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_SYS_RESUS_CTRL_ENABLE |
| // Description : Enable resus |
| #define CLOCKS_CLK_SYS_RESUS_CTRL_ENABLE_RESET _u(0x0) |
| #define CLOCKS_CLK_SYS_RESUS_CTRL_ENABLE_BITS _u(0x00000100) |
| #define CLOCKS_CLK_SYS_RESUS_CTRL_ENABLE_MSB _u(8) |
| #define CLOCKS_CLK_SYS_RESUS_CTRL_ENABLE_LSB _u(8) |
| #define CLOCKS_CLK_SYS_RESUS_CTRL_ENABLE_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_SYS_RESUS_CTRL_TIMEOUT |
| // Description : This is expressed as a number of clk_ref cycles |
| // and must be >= 2x clk_ref_freq/min_clk_tst_freq |
| #define CLOCKS_CLK_SYS_RESUS_CTRL_TIMEOUT_RESET _u(0xff) |
| #define CLOCKS_CLK_SYS_RESUS_CTRL_TIMEOUT_BITS _u(0x000000ff) |
| #define CLOCKS_CLK_SYS_RESUS_CTRL_TIMEOUT_MSB _u(7) |
| #define CLOCKS_CLK_SYS_RESUS_CTRL_TIMEOUT_LSB _u(0) |
| #define CLOCKS_CLK_SYS_RESUS_CTRL_TIMEOUT_ACCESS "RW" |
| // ============================================================================= |
| // Register : CLOCKS_CLK_SYS_RESUS_STATUS |
| // Description : None |
| #define CLOCKS_CLK_SYS_RESUS_STATUS_OFFSET _u(0x0000007c) |
| #define CLOCKS_CLK_SYS_RESUS_STATUS_BITS _u(0x00000001) |
| #define CLOCKS_CLK_SYS_RESUS_STATUS_RESET _u(0x00000000) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_CLK_SYS_RESUS_STATUS_RESUSSED |
| // Description : Clock has been resuscitated, correct the error then send |
| // ctrl_clear=1 |
| #define CLOCKS_CLK_SYS_RESUS_STATUS_RESUSSED_RESET _u(0x0) |
| #define CLOCKS_CLK_SYS_RESUS_STATUS_RESUSSED_BITS _u(0x00000001) |
| #define CLOCKS_CLK_SYS_RESUS_STATUS_RESUSSED_MSB _u(0) |
| #define CLOCKS_CLK_SYS_RESUS_STATUS_RESUSSED_LSB _u(0) |
| #define CLOCKS_CLK_SYS_RESUS_STATUS_RESUSSED_ACCESS "RO" |
| // ============================================================================= |
| // Register : CLOCKS_FC0_REF_KHZ |
| // Description : Reference clock frequency in kHz |
| #define CLOCKS_FC0_REF_KHZ_OFFSET _u(0x00000080) |
| #define CLOCKS_FC0_REF_KHZ_BITS _u(0x000fffff) |
| #define CLOCKS_FC0_REF_KHZ_RESET _u(0x00000000) |
| #define CLOCKS_FC0_REF_KHZ_MSB _u(19) |
| #define CLOCKS_FC0_REF_KHZ_LSB _u(0) |
| #define CLOCKS_FC0_REF_KHZ_ACCESS "RW" |
| // ============================================================================= |
| // Register : CLOCKS_FC0_MIN_KHZ |
| // Description : Minimum pass frequency in kHz. This is optional. Set to 0 if |
| // you are not using the pass/fail flags |
| #define CLOCKS_FC0_MIN_KHZ_OFFSET _u(0x00000084) |
| #define CLOCKS_FC0_MIN_KHZ_BITS _u(0x01ffffff) |
| #define CLOCKS_FC0_MIN_KHZ_RESET _u(0x00000000) |
| #define CLOCKS_FC0_MIN_KHZ_MSB _u(24) |
| #define CLOCKS_FC0_MIN_KHZ_LSB _u(0) |
| #define CLOCKS_FC0_MIN_KHZ_ACCESS "RW" |
| // ============================================================================= |
| // Register : CLOCKS_FC0_MAX_KHZ |
| // Description : Maximum pass frequency in kHz. This is optional. Set to |
| // 0x1ffffff if you are not using the pass/fail flags |
| #define CLOCKS_FC0_MAX_KHZ_OFFSET _u(0x00000088) |
| #define CLOCKS_FC0_MAX_KHZ_BITS _u(0x01ffffff) |
| #define CLOCKS_FC0_MAX_KHZ_RESET _u(0x01ffffff) |
| #define CLOCKS_FC0_MAX_KHZ_MSB _u(24) |
| #define CLOCKS_FC0_MAX_KHZ_LSB _u(0) |
| #define CLOCKS_FC0_MAX_KHZ_ACCESS "RW" |
| // ============================================================================= |
| // Register : CLOCKS_FC0_DELAY |
| // Description : Delays the start of frequency counting to allow the mux to |
| // settle |
| // Delay is measured in multiples of the reference clock period |
| #define CLOCKS_FC0_DELAY_OFFSET _u(0x0000008c) |
| #define CLOCKS_FC0_DELAY_BITS _u(0x00000007) |
| #define CLOCKS_FC0_DELAY_RESET _u(0x00000001) |
| #define CLOCKS_FC0_DELAY_MSB _u(2) |
| #define CLOCKS_FC0_DELAY_LSB _u(0) |
| #define CLOCKS_FC0_DELAY_ACCESS "RW" |
| // ============================================================================= |
| // Register : CLOCKS_FC0_INTERVAL |
| // Description : The test interval is 0.98us * 2**interval, but let's call it |
| // 1us * 2**interval |
| // The default gives a test interval of 250us |
| #define CLOCKS_FC0_INTERVAL_OFFSET _u(0x00000090) |
| #define CLOCKS_FC0_INTERVAL_BITS _u(0x0000000f) |
| #define CLOCKS_FC0_INTERVAL_RESET _u(0x00000008) |
| #define CLOCKS_FC0_INTERVAL_MSB _u(3) |
| #define CLOCKS_FC0_INTERVAL_LSB _u(0) |
| #define CLOCKS_FC0_INTERVAL_ACCESS "RW" |
| // ============================================================================= |
| // Register : CLOCKS_FC0_SRC |
| // Description : Clock sent to frequency counter, set to 0 when not required |
| // Writing to this register initiates the frequency count |
| // 0x00 -> NULL |
| // 0x01 -> pll_sys_clksrc_primary |
| // 0x02 -> pll_usb_clksrc_primary |
| // 0x03 -> rosc_clksrc |
| // 0x04 -> rosc_clksrc_ph |
| // 0x05 -> xosc_clksrc |
| // 0x06 -> clksrc_gpin0 |
| // 0x07 -> clksrc_gpin1 |
| // 0x08 -> clk_ref |
| // 0x09 -> clk_sys |
| // 0x0a -> clk_peri |
| // 0x0b -> clk_usb |
| // 0x0c -> clk_adc |
| // 0x0d -> clk_rtc |
| #define CLOCKS_FC0_SRC_OFFSET _u(0x00000094) |
| #define CLOCKS_FC0_SRC_BITS _u(0x000000ff) |
| #define CLOCKS_FC0_SRC_RESET _u(0x00000000) |
| #define CLOCKS_FC0_SRC_MSB _u(7) |
| #define CLOCKS_FC0_SRC_LSB _u(0) |
| #define CLOCKS_FC0_SRC_ACCESS "RW" |
| #define CLOCKS_FC0_SRC_VALUE_NULL _u(0x00) |
| #define CLOCKS_FC0_SRC_VALUE_PLL_SYS_CLKSRC_PRIMARY _u(0x01) |
| #define CLOCKS_FC0_SRC_VALUE_PLL_USB_CLKSRC_PRIMARY _u(0x02) |
| #define CLOCKS_FC0_SRC_VALUE_ROSC_CLKSRC _u(0x03) |
| #define CLOCKS_FC0_SRC_VALUE_ROSC_CLKSRC_PH _u(0x04) |
| #define CLOCKS_FC0_SRC_VALUE_XOSC_CLKSRC _u(0x05) |
| #define CLOCKS_FC0_SRC_VALUE_CLKSRC_GPIN0 _u(0x06) |
| #define CLOCKS_FC0_SRC_VALUE_CLKSRC_GPIN1 _u(0x07) |
| #define CLOCKS_FC0_SRC_VALUE_CLK_REF _u(0x08) |
| #define CLOCKS_FC0_SRC_VALUE_CLK_SYS _u(0x09) |
| #define CLOCKS_FC0_SRC_VALUE_CLK_PERI _u(0x0a) |
| #define CLOCKS_FC0_SRC_VALUE_CLK_USB _u(0x0b) |
| #define CLOCKS_FC0_SRC_VALUE_CLK_ADC _u(0x0c) |
| #define CLOCKS_FC0_SRC_VALUE_CLK_RTC _u(0x0d) |
| // ============================================================================= |
| // Register : CLOCKS_FC0_STATUS |
| // Description : Frequency counter status |
| #define CLOCKS_FC0_STATUS_OFFSET _u(0x00000098) |
| #define CLOCKS_FC0_STATUS_BITS _u(0x11111111) |
| #define CLOCKS_FC0_STATUS_RESET _u(0x00000000) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_FC0_STATUS_DIED |
| // Description : Test clock stopped during test |
| #define CLOCKS_FC0_STATUS_DIED_RESET _u(0x0) |
| #define CLOCKS_FC0_STATUS_DIED_BITS _u(0x10000000) |
| #define CLOCKS_FC0_STATUS_DIED_MSB _u(28) |
| #define CLOCKS_FC0_STATUS_DIED_LSB _u(28) |
| #define CLOCKS_FC0_STATUS_DIED_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_FC0_STATUS_FAST |
| // Description : Test clock faster than expected, only valid when status_done=1 |
| #define CLOCKS_FC0_STATUS_FAST_RESET _u(0x0) |
| #define CLOCKS_FC0_STATUS_FAST_BITS _u(0x01000000) |
| #define CLOCKS_FC0_STATUS_FAST_MSB _u(24) |
| #define CLOCKS_FC0_STATUS_FAST_LSB _u(24) |
| #define CLOCKS_FC0_STATUS_FAST_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_FC0_STATUS_SLOW |
| // Description : Test clock slower than expected, only valid when status_done=1 |
| #define CLOCKS_FC0_STATUS_SLOW_RESET _u(0x0) |
| #define CLOCKS_FC0_STATUS_SLOW_BITS _u(0x00100000) |
| #define CLOCKS_FC0_STATUS_SLOW_MSB _u(20) |
| #define CLOCKS_FC0_STATUS_SLOW_LSB _u(20) |
| #define CLOCKS_FC0_STATUS_SLOW_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_FC0_STATUS_FAIL |
| // Description : Test failed |
| #define CLOCKS_FC0_STATUS_FAIL_RESET _u(0x0) |
| #define CLOCKS_FC0_STATUS_FAIL_BITS _u(0x00010000) |
| #define CLOCKS_FC0_STATUS_FAIL_MSB _u(16) |
| #define CLOCKS_FC0_STATUS_FAIL_LSB _u(16) |
| #define CLOCKS_FC0_STATUS_FAIL_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_FC0_STATUS_WAITING |
| // Description : Waiting for test clock to start |
| #define CLOCKS_FC0_STATUS_WAITING_RESET _u(0x0) |
| #define CLOCKS_FC0_STATUS_WAITING_BITS _u(0x00001000) |
| #define CLOCKS_FC0_STATUS_WAITING_MSB _u(12) |
| #define CLOCKS_FC0_STATUS_WAITING_LSB _u(12) |
| #define CLOCKS_FC0_STATUS_WAITING_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_FC0_STATUS_RUNNING |
| // Description : Test running |
| #define CLOCKS_FC0_STATUS_RUNNING_RESET _u(0x0) |
| #define CLOCKS_FC0_STATUS_RUNNING_BITS _u(0x00000100) |
| #define CLOCKS_FC0_STATUS_RUNNING_MSB _u(8) |
| #define CLOCKS_FC0_STATUS_RUNNING_LSB _u(8) |
| #define CLOCKS_FC0_STATUS_RUNNING_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_FC0_STATUS_DONE |
| // Description : Test complete |
| #define CLOCKS_FC0_STATUS_DONE_RESET _u(0x0) |
| #define CLOCKS_FC0_STATUS_DONE_BITS _u(0x00000010) |
| #define CLOCKS_FC0_STATUS_DONE_MSB _u(4) |
| #define CLOCKS_FC0_STATUS_DONE_LSB _u(4) |
| #define CLOCKS_FC0_STATUS_DONE_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_FC0_STATUS_PASS |
| // Description : Test passed |
| #define CLOCKS_FC0_STATUS_PASS_RESET _u(0x0) |
| #define CLOCKS_FC0_STATUS_PASS_BITS _u(0x00000001) |
| #define CLOCKS_FC0_STATUS_PASS_MSB _u(0) |
| #define CLOCKS_FC0_STATUS_PASS_LSB _u(0) |
| #define CLOCKS_FC0_STATUS_PASS_ACCESS "RO" |
| // ============================================================================= |
| // Register : CLOCKS_FC0_RESULT |
| // Description : Result of frequency measurement, only valid when status_done=1 |
| #define CLOCKS_FC0_RESULT_OFFSET _u(0x0000009c) |
| #define CLOCKS_FC0_RESULT_BITS _u(0x3fffffff) |
| #define CLOCKS_FC0_RESULT_RESET _u(0x00000000) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_FC0_RESULT_KHZ |
| // Description : None |
| #define CLOCKS_FC0_RESULT_KHZ_RESET _u(0x0000000) |
| #define CLOCKS_FC0_RESULT_KHZ_BITS _u(0x3fffffe0) |
| #define CLOCKS_FC0_RESULT_KHZ_MSB _u(29) |
| #define CLOCKS_FC0_RESULT_KHZ_LSB _u(5) |
| #define CLOCKS_FC0_RESULT_KHZ_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_FC0_RESULT_FRAC |
| // Description : None |
| #define CLOCKS_FC0_RESULT_FRAC_RESET _u(0x00) |
| #define CLOCKS_FC0_RESULT_FRAC_BITS _u(0x0000001f) |
| #define CLOCKS_FC0_RESULT_FRAC_MSB _u(4) |
| #define CLOCKS_FC0_RESULT_FRAC_LSB _u(0) |
| #define CLOCKS_FC0_RESULT_FRAC_ACCESS "RO" |
| // ============================================================================= |
| // Register : CLOCKS_WAKE_EN0 |
| // Description : enable clock in wake mode |
| #define CLOCKS_WAKE_EN0_OFFSET _u(0x000000a0) |
| #define CLOCKS_WAKE_EN0_BITS _u(0xffffffff) |
| #define CLOCKS_WAKE_EN0_RESET _u(0xffffffff) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_SYS_SRAM3 |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SRAM3_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SRAM3_BITS _u(0x80000000) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SRAM3_MSB _u(31) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SRAM3_LSB _u(31) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SRAM3_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_SYS_SRAM2 |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SRAM2_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SRAM2_BITS _u(0x40000000) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SRAM2_MSB _u(30) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SRAM2_LSB _u(30) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SRAM2_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_SYS_SRAM1 |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SRAM1_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SRAM1_BITS _u(0x20000000) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SRAM1_MSB _u(29) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SRAM1_LSB _u(29) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SRAM1_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_SYS_SRAM0 |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SRAM0_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SRAM0_BITS _u(0x10000000) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SRAM0_MSB _u(28) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SRAM0_LSB _u(28) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SRAM0_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_SYS_SPI1 |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SPI1_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SPI1_BITS _u(0x08000000) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SPI1_MSB _u(27) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SPI1_LSB _u(27) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SPI1_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_PERI_SPI1 |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_PERI_SPI1_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_PERI_SPI1_BITS _u(0x04000000) |
| #define CLOCKS_WAKE_EN0_CLK_PERI_SPI1_MSB _u(26) |
| #define CLOCKS_WAKE_EN0_CLK_PERI_SPI1_LSB _u(26) |
| #define CLOCKS_WAKE_EN0_CLK_PERI_SPI1_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_SYS_SPI0 |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SPI0_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SPI0_BITS _u(0x02000000) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SPI0_MSB _u(25) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SPI0_LSB _u(25) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SPI0_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_PERI_SPI0 |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_PERI_SPI0_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_PERI_SPI0_BITS _u(0x01000000) |
| #define CLOCKS_WAKE_EN0_CLK_PERI_SPI0_MSB _u(24) |
| #define CLOCKS_WAKE_EN0_CLK_PERI_SPI0_LSB _u(24) |
| #define CLOCKS_WAKE_EN0_CLK_PERI_SPI0_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_SYS_SIO |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SIO_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SIO_BITS _u(0x00800000) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SIO_MSB _u(23) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SIO_LSB _u(23) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_SIO_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_SYS_RTC |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_SYS_RTC_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_RTC_BITS _u(0x00400000) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_RTC_MSB _u(22) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_RTC_LSB _u(22) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_RTC_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_RTC_RTC |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_RTC_RTC_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_RTC_RTC_BITS _u(0x00200000) |
| #define CLOCKS_WAKE_EN0_CLK_RTC_RTC_MSB _u(21) |
| #define CLOCKS_WAKE_EN0_CLK_RTC_RTC_LSB _u(21) |
| #define CLOCKS_WAKE_EN0_CLK_RTC_RTC_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_SYS_ROSC |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_SYS_ROSC_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_ROSC_BITS _u(0x00100000) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_ROSC_MSB _u(20) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_ROSC_LSB _u(20) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_ROSC_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_SYS_ROM |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_SYS_ROM_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_ROM_BITS _u(0x00080000) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_ROM_MSB _u(19) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_ROM_LSB _u(19) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_ROM_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_SYS_RESETS |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_SYS_RESETS_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_RESETS_BITS _u(0x00040000) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_RESETS_MSB _u(18) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_RESETS_LSB _u(18) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_RESETS_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_SYS_PWM |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PWM_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PWM_BITS _u(0x00020000) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PWM_MSB _u(17) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PWM_LSB _u(17) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PWM_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_SYS_PSM |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PSM_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PSM_BITS _u(0x00010000) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PSM_MSB _u(16) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PSM_LSB _u(16) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PSM_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_SYS_PLL_USB |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PLL_USB_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PLL_USB_BITS _u(0x00008000) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PLL_USB_MSB _u(15) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PLL_USB_LSB _u(15) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PLL_USB_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_SYS_PLL_SYS |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PLL_SYS_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PLL_SYS_BITS _u(0x00004000) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PLL_SYS_MSB _u(14) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PLL_SYS_LSB _u(14) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PLL_SYS_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_SYS_PIO1 |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PIO1_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PIO1_BITS _u(0x00002000) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PIO1_MSB _u(13) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PIO1_LSB _u(13) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PIO1_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_SYS_PIO0 |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PIO0_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PIO0_BITS _u(0x00001000) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PIO0_MSB _u(12) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PIO0_LSB _u(12) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PIO0_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_SYS_PADS |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PADS_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PADS_BITS _u(0x00000800) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PADS_MSB _u(11) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PADS_LSB _u(11) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_PADS_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_SYS_VREG_AND_CHIP_RESET |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_SYS_VREG_AND_CHIP_RESET_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_VREG_AND_CHIP_RESET_BITS _u(0x00000400) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_VREG_AND_CHIP_RESET_MSB _u(10) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_VREG_AND_CHIP_RESET_LSB _u(10) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_VREG_AND_CHIP_RESET_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_SYS_JTAG |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_SYS_JTAG_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_JTAG_BITS _u(0x00000200) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_JTAG_MSB _u(9) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_JTAG_LSB _u(9) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_JTAG_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_SYS_IO |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_SYS_IO_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_IO_BITS _u(0x00000100) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_IO_MSB _u(8) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_IO_LSB _u(8) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_IO_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_SYS_I2C1 |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_SYS_I2C1_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_I2C1_BITS _u(0x00000080) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_I2C1_MSB _u(7) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_I2C1_LSB _u(7) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_I2C1_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_SYS_I2C0 |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_SYS_I2C0_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_I2C0_BITS _u(0x00000040) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_I2C0_MSB _u(6) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_I2C0_LSB _u(6) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_I2C0_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_SYS_DMA |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_SYS_DMA_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_DMA_BITS _u(0x00000020) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_DMA_MSB _u(5) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_DMA_LSB _u(5) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_DMA_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_SYS_BUSFABRIC |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_SYS_BUSFABRIC_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_BUSFABRIC_BITS _u(0x00000010) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_BUSFABRIC_MSB _u(4) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_BUSFABRIC_LSB _u(4) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_BUSFABRIC_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_SYS_BUSCTRL |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_SYS_BUSCTRL_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_BUSCTRL_BITS _u(0x00000008) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_BUSCTRL_MSB _u(3) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_BUSCTRL_LSB _u(3) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_BUSCTRL_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_SYS_ADC |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_SYS_ADC_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_ADC_BITS _u(0x00000004) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_ADC_MSB _u(2) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_ADC_LSB _u(2) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_ADC_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_ADC_ADC |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_ADC_ADC_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_ADC_ADC_BITS _u(0x00000002) |
| #define CLOCKS_WAKE_EN0_CLK_ADC_ADC_MSB _u(1) |
| #define CLOCKS_WAKE_EN0_CLK_ADC_ADC_LSB _u(1) |
| #define CLOCKS_WAKE_EN0_CLK_ADC_ADC_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN0_CLK_SYS_CLOCKS |
| // Description : None |
| #define CLOCKS_WAKE_EN0_CLK_SYS_CLOCKS_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_CLOCKS_BITS _u(0x00000001) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_CLOCKS_MSB _u(0) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_CLOCKS_LSB _u(0) |
| #define CLOCKS_WAKE_EN0_CLK_SYS_CLOCKS_ACCESS "RW" |
| // ============================================================================= |
| // Register : CLOCKS_WAKE_EN1 |
| // Description : enable clock in wake mode |
| #define CLOCKS_WAKE_EN1_OFFSET _u(0x000000a4) |
| #define CLOCKS_WAKE_EN1_BITS _u(0x00007fff) |
| #define CLOCKS_WAKE_EN1_RESET _u(0x00007fff) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN1_CLK_SYS_XOSC |
| // Description : None |
| #define CLOCKS_WAKE_EN1_CLK_SYS_XOSC_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_XOSC_BITS _u(0x00004000) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_XOSC_MSB _u(14) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_XOSC_LSB _u(14) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_XOSC_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN1_CLK_SYS_XIP |
| // Description : None |
| #define CLOCKS_WAKE_EN1_CLK_SYS_XIP_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_XIP_BITS _u(0x00002000) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_XIP_MSB _u(13) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_XIP_LSB _u(13) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_XIP_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN1_CLK_SYS_WATCHDOG |
| // Description : None |
| #define CLOCKS_WAKE_EN1_CLK_SYS_WATCHDOG_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_WATCHDOG_BITS _u(0x00001000) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_WATCHDOG_MSB _u(12) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_WATCHDOG_LSB _u(12) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_WATCHDOG_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN1_CLK_USB_USBCTRL |
| // Description : None |
| #define CLOCKS_WAKE_EN1_CLK_USB_USBCTRL_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN1_CLK_USB_USBCTRL_BITS _u(0x00000800) |
| #define CLOCKS_WAKE_EN1_CLK_USB_USBCTRL_MSB _u(11) |
| #define CLOCKS_WAKE_EN1_CLK_USB_USBCTRL_LSB _u(11) |
| #define CLOCKS_WAKE_EN1_CLK_USB_USBCTRL_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN1_CLK_SYS_USBCTRL |
| // Description : None |
| #define CLOCKS_WAKE_EN1_CLK_SYS_USBCTRL_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_USBCTRL_BITS _u(0x00000400) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_USBCTRL_MSB _u(10) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_USBCTRL_LSB _u(10) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_USBCTRL_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN1_CLK_SYS_UART1 |
| // Description : None |
| #define CLOCKS_WAKE_EN1_CLK_SYS_UART1_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_UART1_BITS _u(0x00000200) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_UART1_MSB _u(9) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_UART1_LSB _u(9) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_UART1_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN1_CLK_PERI_UART1 |
| // Description : None |
| #define CLOCKS_WAKE_EN1_CLK_PERI_UART1_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN1_CLK_PERI_UART1_BITS _u(0x00000100) |
| #define CLOCKS_WAKE_EN1_CLK_PERI_UART1_MSB _u(8) |
| #define CLOCKS_WAKE_EN1_CLK_PERI_UART1_LSB _u(8) |
| #define CLOCKS_WAKE_EN1_CLK_PERI_UART1_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN1_CLK_SYS_UART0 |
| // Description : None |
| #define CLOCKS_WAKE_EN1_CLK_SYS_UART0_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_UART0_BITS _u(0x00000080) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_UART0_MSB _u(7) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_UART0_LSB _u(7) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_UART0_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN1_CLK_PERI_UART0 |
| // Description : None |
| #define CLOCKS_WAKE_EN1_CLK_PERI_UART0_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN1_CLK_PERI_UART0_BITS _u(0x00000040) |
| #define CLOCKS_WAKE_EN1_CLK_PERI_UART0_MSB _u(6) |
| #define CLOCKS_WAKE_EN1_CLK_PERI_UART0_LSB _u(6) |
| #define CLOCKS_WAKE_EN1_CLK_PERI_UART0_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN1_CLK_SYS_TIMER |
| // Description : None |
| #define CLOCKS_WAKE_EN1_CLK_SYS_TIMER_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_TIMER_BITS _u(0x00000020) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_TIMER_MSB _u(5) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_TIMER_LSB _u(5) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_TIMER_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN1_CLK_SYS_TBMAN |
| // Description : None |
| #define CLOCKS_WAKE_EN1_CLK_SYS_TBMAN_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_TBMAN_BITS _u(0x00000010) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_TBMAN_MSB _u(4) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_TBMAN_LSB _u(4) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_TBMAN_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN1_CLK_SYS_SYSINFO |
| // Description : None |
| #define CLOCKS_WAKE_EN1_CLK_SYS_SYSINFO_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_SYSINFO_BITS _u(0x00000008) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_SYSINFO_MSB _u(3) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_SYSINFO_LSB _u(3) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_SYSINFO_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN1_CLK_SYS_SYSCFG |
| // Description : None |
| #define CLOCKS_WAKE_EN1_CLK_SYS_SYSCFG_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_SYSCFG_BITS _u(0x00000004) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_SYSCFG_MSB _u(2) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_SYSCFG_LSB _u(2) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_SYSCFG_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN1_CLK_SYS_SRAM5 |
| // Description : None |
| #define CLOCKS_WAKE_EN1_CLK_SYS_SRAM5_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_SRAM5_BITS _u(0x00000002) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_SRAM5_MSB _u(1) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_SRAM5_LSB _u(1) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_SRAM5_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_WAKE_EN1_CLK_SYS_SRAM4 |
| // Description : None |
| #define CLOCKS_WAKE_EN1_CLK_SYS_SRAM4_RESET _u(0x1) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_SRAM4_BITS _u(0x00000001) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_SRAM4_MSB _u(0) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_SRAM4_LSB _u(0) |
| #define CLOCKS_WAKE_EN1_CLK_SYS_SRAM4_ACCESS "RW" |
| // ============================================================================= |
| // Register : CLOCKS_SLEEP_EN0 |
| // Description : enable clock in sleep mode |
| #define CLOCKS_SLEEP_EN0_OFFSET _u(0x000000a8) |
| #define CLOCKS_SLEEP_EN0_BITS _u(0xffffffff) |
| #define CLOCKS_SLEEP_EN0_RESET _u(0xffffffff) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_SYS_SRAM3 |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SRAM3_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SRAM3_BITS _u(0x80000000) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SRAM3_MSB _u(31) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SRAM3_LSB _u(31) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SRAM3_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_SYS_SRAM2 |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SRAM2_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SRAM2_BITS _u(0x40000000) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SRAM2_MSB _u(30) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SRAM2_LSB _u(30) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SRAM2_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_SYS_SRAM1 |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SRAM1_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SRAM1_BITS _u(0x20000000) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SRAM1_MSB _u(29) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SRAM1_LSB _u(29) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SRAM1_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_SYS_SRAM0 |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SRAM0_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SRAM0_BITS _u(0x10000000) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SRAM0_MSB _u(28) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SRAM0_LSB _u(28) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SRAM0_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_SYS_SPI1 |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SPI1_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SPI1_BITS _u(0x08000000) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SPI1_MSB _u(27) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SPI1_LSB _u(27) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SPI1_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_PERI_SPI1 |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_PERI_SPI1_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_PERI_SPI1_BITS _u(0x04000000) |
| #define CLOCKS_SLEEP_EN0_CLK_PERI_SPI1_MSB _u(26) |
| #define CLOCKS_SLEEP_EN0_CLK_PERI_SPI1_LSB _u(26) |
| #define CLOCKS_SLEEP_EN0_CLK_PERI_SPI1_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_SYS_SPI0 |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SPI0_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SPI0_BITS _u(0x02000000) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SPI0_MSB _u(25) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SPI0_LSB _u(25) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SPI0_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_PERI_SPI0 |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_PERI_SPI0_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_PERI_SPI0_BITS _u(0x01000000) |
| #define CLOCKS_SLEEP_EN0_CLK_PERI_SPI0_MSB _u(24) |
| #define CLOCKS_SLEEP_EN0_CLK_PERI_SPI0_LSB _u(24) |
| #define CLOCKS_SLEEP_EN0_CLK_PERI_SPI0_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_SYS_SIO |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SIO_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SIO_BITS _u(0x00800000) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SIO_MSB _u(23) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SIO_LSB _u(23) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_SIO_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_SYS_RTC |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_RTC_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_RTC_BITS _u(0x00400000) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_RTC_MSB _u(22) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_RTC_LSB _u(22) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_RTC_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_RTC_RTC |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_RTC_RTC_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_RTC_RTC_BITS _u(0x00200000) |
| #define CLOCKS_SLEEP_EN0_CLK_RTC_RTC_MSB _u(21) |
| #define CLOCKS_SLEEP_EN0_CLK_RTC_RTC_LSB _u(21) |
| #define CLOCKS_SLEEP_EN0_CLK_RTC_RTC_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_SYS_ROSC |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_ROSC_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_ROSC_BITS _u(0x00100000) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_ROSC_MSB _u(20) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_ROSC_LSB _u(20) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_ROSC_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_SYS_ROM |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_ROM_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_ROM_BITS _u(0x00080000) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_ROM_MSB _u(19) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_ROM_LSB _u(19) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_ROM_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_SYS_RESETS |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_RESETS_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_RESETS_BITS _u(0x00040000) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_RESETS_MSB _u(18) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_RESETS_LSB _u(18) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_RESETS_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_SYS_PWM |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PWM_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PWM_BITS _u(0x00020000) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PWM_MSB _u(17) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PWM_LSB _u(17) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PWM_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_SYS_PSM |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PSM_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PSM_BITS _u(0x00010000) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PSM_MSB _u(16) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PSM_LSB _u(16) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PSM_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_SYS_PLL_USB |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PLL_USB_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PLL_USB_BITS _u(0x00008000) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PLL_USB_MSB _u(15) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PLL_USB_LSB _u(15) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PLL_USB_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_SYS_PLL_SYS |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PLL_SYS_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PLL_SYS_BITS _u(0x00004000) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PLL_SYS_MSB _u(14) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PLL_SYS_LSB _u(14) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PLL_SYS_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_SYS_PIO1 |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PIO1_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PIO1_BITS _u(0x00002000) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PIO1_MSB _u(13) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PIO1_LSB _u(13) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PIO1_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_SYS_PIO0 |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PIO0_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PIO0_BITS _u(0x00001000) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PIO0_MSB _u(12) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PIO0_LSB _u(12) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PIO0_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_SYS_PADS |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PADS_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PADS_BITS _u(0x00000800) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PADS_MSB _u(11) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PADS_LSB _u(11) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_PADS_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_SYS_VREG_AND_CHIP_RESET |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_VREG_AND_CHIP_RESET_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_VREG_AND_CHIP_RESET_BITS _u(0x00000400) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_VREG_AND_CHIP_RESET_MSB _u(10) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_VREG_AND_CHIP_RESET_LSB _u(10) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_VREG_AND_CHIP_RESET_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_SYS_JTAG |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_JTAG_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_JTAG_BITS _u(0x00000200) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_JTAG_MSB _u(9) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_JTAG_LSB _u(9) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_JTAG_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_SYS_IO |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_IO_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_IO_BITS _u(0x00000100) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_IO_MSB _u(8) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_IO_LSB _u(8) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_IO_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_SYS_I2C1 |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_I2C1_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_I2C1_BITS _u(0x00000080) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_I2C1_MSB _u(7) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_I2C1_LSB _u(7) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_I2C1_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_SYS_I2C0 |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_I2C0_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_I2C0_BITS _u(0x00000040) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_I2C0_MSB _u(6) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_I2C0_LSB _u(6) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_I2C0_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_SYS_DMA |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_DMA_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_DMA_BITS _u(0x00000020) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_DMA_MSB _u(5) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_DMA_LSB _u(5) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_DMA_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_SYS_BUSFABRIC |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_BUSFABRIC_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_BUSFABRIC_BITS _u(0x00000010) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_BUSFABRIC_MSB _u(4) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_BUSFABRIC_LSB _u(4) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_BUSFABRIC_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_SYS_BUSCTRL |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_BUSCTRL_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_BUSCTRL_BITS _u(0x00000008) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_BUSCTRL_MSB _u(3) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_BUSCTRL_LSB _u(3) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_BUSCTRL_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_SYS_ADC |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_ADC_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_ADC_BITS _u(0x00000004) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_ADC_MSB _u(2) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_ADC_LSB _u(2) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_ADC_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_ADC_ADC |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_ADC_ADC_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_ADC_ADC_BITS _u(0x00000002) |
| #define CLOCKS_SLEEP_EN0_CLK_ADC_ADC_MSB _u(1) |
| #define CLOCKS_SLEEP_EN0_CLK_ADC_ADC_LSB _u(1) |
| #define CLOCKS_SLEEP_EN0_CLK_ADC_ADC_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN0_CLK_SYS_CLOCKS |
| // Description : None |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_CLOCKS_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_CLOCKS_BITS _u(0x00000001) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_CLOCKS_MSB _u(0) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_CLOCKS_LSB _u(0) |
| #define CLOCKS_SLEEP_EN0_CLK_SYS_CLOCKS_ACCESS "RW" |
| // ============================================================================= |
| // Register : CLOCKS_SLEEP_EN1 |
| // Description : enable clock in sleep mode |
| #define CLOCKS_SLEEP_EN1_OFFSET _u(0x000000ac) |
| #define CLOCKS_SLEEP_EN1_BITS _u(0x00007fff) |
| #define CLOCKS_SLEEP_EN1_RESET _u(0x00007fff) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN1_CLK_SYS_XOSC |
| // Description : None |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_XOSC_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_XOSC_BITS _u(0x00004000) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_XOSC_MSB _u(14) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_XOSC_LSB _u(14) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_XOSC_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN1_CLK_SYS_XIP |
| // Description : None |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_XIP_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_XIP_BITS _u(0x00002000) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_XIP_MSB _u(13) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_XIP_LSB _u(13) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_XIP_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN1_CLK_SYS_WATCHDOG |
| // Description : None |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_WATCHDOG_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_WATCHDOG_BITS _u(0x00001000) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_WATCHDOG_MSB _u(12) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_WATCHDOG_LSB _u(12) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_WATCHDOG_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN1_CLK_USB_USBCTRL |
| // Description : None |
| #define CLOCKS_SLEEP_EN1_CLK_USB_USBCTRL_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN1_CLK_USB_USBCTRL_BITS _u(0x00000800) |
| #define CLOCKS_SLEEP_EN1_CLK_USB_USBCTRL_MSB _u(11) |
| #define CLOCKS_SLEEP_EN1_CLK_USB_USBCTRL_LSB _u(11) |
| #define CLOCKS_SLEEP_EN1_CLK_USB_USBCTRL_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN1_CLK_SYS_USBCTRL |
| // Description : None |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_USBCTRL_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_USBCTRL_BITS _u(0x00000400) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_USBCTRL_MSB _u(10) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_USBCTRL_LSB _u(10) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_USBCTRL_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN1_CLK_SYS_UART1 |
| // Description : None |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_UART1_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_UART1_BITS _u(0x00000200) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_UART1_MSB _u(9) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_UART1_LSB _u(9) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_UART1_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN1_CLK_PERI_UART1 |
| // Description : None |
| #define CLOCKS_SLEEP_EN1_CLK_PERI_UART1_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN1_CLK_PERI_UART1_BITS _u(0x00000100) |
| #define CLOCKS_SLEEP_EN1_CLK_PERI_UART1_MSB _u(8) |
| #define CLOCKS_SLEEP_EN1_CLK_PERI_UART1_LSB _u(8) |
| #define CLOCKS_SLEEP_EN1_CLK_PERI_UART1_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN1_CLK_SYS_UART0 |
| // Description : None |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_UART0_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_UART0_BITS _u(0x00000080) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_UART0_MSB _u(7) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_UART0_LSB _u(7) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_UART0_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN1_CLK_PERI_UART0 |
| // Description : None |
| #define CLOCKS_SLEEP_EN1_CLK_PERI_UART0_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN1_CLK_PERI_UART0_BITS _u(0x00000040) |
| #define CLOCKS_SLEEP_EN1_CLK_PERI_UART0_MSB _u(6) |
| #define CLOCKS_SLEEP_EN1_CLK_PERI_UART0_LSB _u(6) |
| #define CLOCKS_SLEEP_EN1_CLK_PERI_UART0_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN1_CLK_SYS_TIMER |
| // Description : None |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_TIMER_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_TIMER_BITS _u(0x00000020) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_TIMER_MSB _u(5) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_TIMER_LSB _u(5) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_TIMER_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN1_CLK_SYS_TBMAN |
| // Description : None |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_TBMAN_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_TBMAN_BITS _u(0x00000010) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_TBMAN_MSB _u(4) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_TBMAN_LSB _u(4) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_TBMAN_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN1_CLK_SYS_SYSINFO |
| // Description : None |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_SYSINFO_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_SYSINFO_BITS _u(0x00000008) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_SYSINFO_MSB _u(3) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_SYSINFO_LSB _u(3) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_SYSINFO_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN1_CLK_SYS_SYSCFG |
| // Description : None |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_SYSCFG_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_SYSCFG_BITS _u(0x00000004) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_SYSCFG_MSB _u(2) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_SYSCFG_LSB _u(2) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_SYSCFG_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN1_CLK_SYS_SRAM5 |
| // Description : None |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_SRAM5_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_SRAM5_BITS _u(0x00000002) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_SRAM5_MSB _u(1) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_SRAM5_LSB _u(1) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_SRAM5_ACCESS "RW" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_SLEEP_EN1_CLK_SYS_SRAM4 |
| // Description : None |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_SRAM4_RESET _u(0x1) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_SRAM4_BITS _u(0x00000001) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_SRAM4_MSB _u(0) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_SRAM4_LSB _u(0) |
| #define CLOCKS_SLEEP_EN1_CLK_SYS_SRAM4_ACCESS "RW" |
| // ============================================================================= |
| // Register : CLOCKS_ENABLED0 |
| // Description : indicates the state of the clock enable |
| #define CLOCKS_ENABLED0_OFFSET _u(0x000000b0) |
| #define CLOCKS_ENABLED0_BITS _u(0xffffffff) |
| #define CLOCKS_ENABLED0_RESET _u(0x00000000) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_SYS_SRAM3 |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_SYS_SRAM3_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_SYS_SRAM3_BITS _u(0x80000000) |
| #define CLOCKS_ENABLED0_CLK_SYS_SRAM3_MSB _u(31) |
| #define CLOCKS_ENABLED0_CLK_SYS_SRAM3_LSB _u(31) |
| #define CLOCKS_ENABLED0_CLK_SYS_SRAM3_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_SYS_SRAM2 |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_SYS_SRAM2_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_SYS_SRAM2_BITS _u(0x40000000) |
| #define CLOCKS_ENABLED0_CLK_SYS_SRAM2_MSB _u(30) |
| #define CLOCKS_ENABLED0_CLK_SYS_SRAM2_LSB _u(30) |
| #define CLOCKS_ENABLED0_CLK_SYS_SRAM2_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_SYS_SRAM1 |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_SYS_SRAM1_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_SYS_SRAM1_BITS _u(0x20000000) |
| #define CLOCKS_ENABLED0_CLK_SYS_SRAM1_MSB _u(29) |
| #define CLOCKS_ENABLED0_CLK_SYS_SRAM1_LSB _u(29) |
| #define CLOCKS_ENABLED0_CLK_SYS_SRAM1_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_SYS_SRAM0 |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_SYS_SRAM0_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_SYS_SRAM0_BITS _u(0x10000000) |
| #define CLOCKS_ENABLED0_CLK_SYS_SRAM0_MSB _u(28) |
| #define CLOCKS_ENABLED0_CLK_SYS_SRAM0_LSB _u(28) |
| #define CLOCKS_ENABLED0_CLK_SYS_SRAM0_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_SYS_SPI1 |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_SYS_SPI1_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_SYS_SPI1_BITS _u(0x08000000) |
| #define CLOCKS_ENABLED0_CLK_SYS_SPI1_MSB _u(27) |
| #define CLOCKS_ENABLED0_CLK_SYS_SPI1_LSB _u(27) |
| #define CLOCKS_ENABLED0_CLK_SYS_SPI1_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_PERI_SPI1 |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_PERI_SPI1_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_PERI_SPI1_BITS _u(0x04000000) |
| #define CLOCKS_ENABLED0_CLK_PERI_SPI1_MSB _u(26) |
| #define CLOCKS_ENABLED0_CLK_PERI_SPI1_LSB _u(26) |
| #define CLOCKS_ENABLED0_CLK_PERI_SPI1_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_SYS_SPI0 |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_SYS_SPI0_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_SYS_SPI0_BITS _u(0x02000000) |
| #define CLOCKS_ENABLED0_CLK_SYS_SPI0_MSB _u(25) |
| #define CLOCKS_ENABLED0_CLK_SYS_SPI0_LSB _u(25) |
| #define CLOCKS_ENABLED0_CLK_SYS_SPI0_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_PERI_SPI0 |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_PERI_SPI0_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_PERI_SPI0_BITS _u(0x01000000) |
| #define CLOCKS_ENABLED0_CLK_PERI_SPI0_MSB _u(24) |
| #define CLOCKS_ENABLED0_CLK_PERI_SPI0_LSB _u(24) |
| #define CLOCKS_ENABLED0_CLK_PERI_SPI0_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_SYS_SIO |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_SYS_SIO_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_SYS_SIO_BITS _u(0x00800000) |
| #define CLOCKS_ENABLED0_CLK_SYS_SIO_MSB _u(23) |
| #define CLOCKS_ENABLED0_CLK_SYS_SIO_LSB _u(23) |
| #define CLOCKS_ENABLED0_CLK_SYS_SIO_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_SYS_RTC |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_SYS_RTC_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_SYS_RTC_BITS _u(0x00400000) |
| #define CLOCKS_ENABLED0_CLK_SYS_RTC_MSB _u(22) |
| #define CLOCKS_ENABLED0_CLK_SYS_RTC_LSB _u(22) |
| #define CLOCKS_ENABLED0_CLK_SYS_RTC_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_RTC_RTC |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_RTC_RTC_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_RTC_RTC_BITS _u(0x00200000) |
| #define CLOCKS_ENABLED0_CLK_RTC_RTC_MSB _u(21) |
| #define CLOCKS_ENABLED0_CLK_RTC_RTC_LSB _u(21) |
| #define CLOCKS_ENABLED0_CLK_RTC_RTC_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_SYS_ROSC |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_SYS_ROSC_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_SYS_ROSC_BITS _u(0x00100000) |
| #define CLOCKS_ENABLED0_CLK_SYS_ROSC_MSB _u(20) |
| #define CLOCKS_ENABLED0_CLK_SYS_ROSC_LSB _u(20) |
| #define CLOCKS_ENABLED0_CLK_SYS_ROSC_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_SYS_ROM |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_SYS_ROM_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_SYS_ROM_BITS _u(0x00080000) |
| #define CLOCKS_ENABLED0_CLK_SYS_ROM_MSB _u(19) |
| #define CLOCKS_ENABLED0_CLK_SYS_ROM_LSB _u(19) |
| #define CLOCKS_ENABLED0_CLK_SYS_ROM_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_SYS_RESETS |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_SYS_RESETS_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_SYS_RESETS_BITS _u(0x00040000) |
| #define CLOCKS_ENABLED0_CLK_SYS_RESETS_MSB _u(18) |
| #define CLOCKS_ENABLED0_CLK_SYS_RESETS_LSB _u(18) |
| #define CLOCKS_ENABLED0_CLK_SYS_RESETS_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_SYS_PWM |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_SYS_PWM_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_SYS_PWM_BITS _u(0x00020000) |
| #define CLOCKS_ENABLED0_CLK_SYS_PWM_MSB _u(17) |
| #define CLOCKS_ENABLED0_CLK_SYS_PWM_LSB _u(17) |
| #define CLOCKS_ENABLED0_CLK_SYS_PWM_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_SYS_PSM |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_SYS_PSM_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_SYS_PSM_BITS _u(0x00010000) |
| #define CLOCKS_ENABLED0_CLK_SYS_PSM_MSB _u(16) |
| #define CLOCKS_ENABLED0_CLK_SYS_PSM_LSB _u(16) |
| #define CLOCKS_ENABLED0_CLK_SYS_PSM_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_SYS_PLL_USB |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_SYS_PLL_USB_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_SYS_PLL_USB_BITS _u(0x00008000) |
| #define CLOCKS_ENABLED0_CLK_SYS_PLL_USB_MSB _u(15) |
| #define CLOCKS_ENABLED0_CLK_SYS_PLL_USB_LSB _u(15) |
| #define CLOCKS_ENABLED0_CLK_SYS_PLL_USB_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_SYS_PLL_SYS |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_SYS_PLL_SYS_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_SYS_PLL_SYS_BITS _u(0x00004000) |
| #define CLOCKS_ENABLED0_CLK_SYS_PLL_SYS_MSB _u(14) |
| #define CLOCKS_ENABLED0_CLK_SYS_PLL_SYS_LSB _u(14) |
| #define CLOCKS_ENABLED0_CLK_SYS_PLL_SYS_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_SYS_PIO1 |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_SYS_PIO1_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_SYS_PIO1_BITS _u(0x00002000) |
| #define CLOCKS_ENABLED0_CLK_SYS_PIO1_MSB _u(13) |
| #define CLOCKS_ENABLED0_CLK_SYS_PIO1_LSB _u(13) |
| #define CLOCKS_ENABLED0_CLK_SYS_PIO1_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_SYS_PIO0 |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_SYS_PIO0_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_SYS_PIO0_BITS _u(0x00001000) |
| #define CLOCKS_ENABLED0_CLK_SYS_PIO0_MSB _u(12) |
| #define CLOCKS_ENABLED0_CLK_SYS_PIO0_LSB _u(12) |
| #define CLOCKS_ENABLED0_CLK_SYS_PIO0_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_SYS_PADS |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_SYS_PADS_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_SYS_PADS_BITS _u(0x00000800) |
| #define CLOCKS_ENABLED0_CLK_SYS_PADS_MSB _u(11) |
| #define CLOCKS_ENABLED0_CLK_SYS_PADS_LSB _u(11) |
| #define CLOCKS_ENABLED0_CLK_SYS_PADS_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_SYS_VREG_AND_CHIP_RESET |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_SYS_VREG_AND_CHIP_RESET_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_SYS_VREG_AND_CHIP_RESET_BITS _u(0x00000400) |
| #define CLOCKS_ENABLED0_CLK_SYS_VREG_AND_CHIP_RESET_MSB _u(10) |
| #define CLOCKS_ENABLED0_CLK_SYS_VREG_AND_CHIP_RESET_LSB _u(10) |
| #define CLOCKS_ENABLED0_CLK_SYS_VREG_AND_CHIP_RESET_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_SYS_JTAG |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_SYS_JTAG_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_SYS_JTAG_BITS _u(0x00000200) |
| #define CLOCKS_ENABLED0_CLK_SYS_JTAG_MSB _u(9) |
| #define CLOCKS_ENABLED0_CLK_SYS_JTAG_LSB _u(9) |
| #define CLOCKS_ENABLED0_CLK_SYS_JTAG_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_SYS_IO |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_SYS_IO_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_SYS_IO_BITS _u(0x00000100) |
| #define CLOCKS_ENABLED0_CLK_SYS_IO_MSB _u(8) |
| #define CLOCKS_ENABLED0_CLK_SYS_IO_LSB _u(8) |
| #define CLOCKS_ENABLED0_CLK_SYS_IO_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_SYS_I2C1 |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_SYS_I2C1_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_SYS_I2C1_BITS _u(0x00000080) |
| #define CLOCKS_ENABLED0_CLK_SYS_I2C1_MSB _u(7) |
| #define CLOCKS_ENABLED0_CLK_SYS_I2C1_LSB _u(7) |
| #define CLOCKS_ENABLED0_CLK_SYS_I2C1_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_SYS_I2C0 |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_SYS_I2C0_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_SYS_I2C0_BITS _u(0x00000040) |
| #define CLOCKS_ENABLED0_CLK_SYS_I2C0_MSB _u(6) |
| #define CLOCKS_ENABLED0_CLK_SYS_I2C0_LSB _u(6) |
| #define CLOCKS_ENABLED0_CLK_SYS_I2C0_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_SYS_DMA |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_SYS_DMA_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_SYS_DMA_BITS _u(0x00000020) |
| #define CLOCKS_ENABLED0_CLK_SYS_DMA_MSB _u(5) |
| #define CLOCKS_ENABLED0_CLK_SYS_DMA_LSB _u(5) |
| #define CLOCKS_ENABLED0_CLK_SYS_DMA_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_SYS_BUSFABRIC |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_SYS_BUSFABRIC_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_SYS_BUSFABRIC_BITS _u(0x00000010) |
| #define CLOCKS_ENABLED0_CLK_SYS_BUSFABRIC_MSB _u(4) |
| #define CLOCKS_ENABLED0_CLK_SYS_BUSFABRIC_LSB _u(4) |
| #define CLOCKS_ENABLED0_CLK_SYS_BUSFABRIC_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_SYS_BUSCTRL |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_SYS_BUSCTRL_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_SYS_BUSCTRL_BITS _u(0x00000008) |
| #define CLOCKS_ENABLED0_CLK_SYS_BUSCTRL_MSB _u(3) |
| #define CLOCKS_ENABLED0_CLK_SYS_BUSCTRL_LSB _u(3) |
| #define CLOCKS_ENABLED0_CLK_SYS_BUSCTRL_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_SYS_ADC |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_SYS_ADC_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_SYS_ADC_BITS _u(0x00000004) |
| #define CLOCKS_ENABLED0_CLK_SYS_ADC_MSB _u(2) |
| #define CLOCKS_ENABLED0_CLK_SYS_ADC_LSB _u(2) |
| #define CLOCKS_ENABLED0_CLK_SYS_ADC_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_ADC_ADC |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_ADC_ADC_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_ADC_ADC_BITS _u(0x00000002) |
| #define CLOCKS_ENABLED0_CLK_ADC_ADC_MSB _u(1) |
| #define CLOCKS_ENABLED0_CLK_ADC_ADC_LSB _u(1) |
| #define CLOCKS_ENABLED0_CLK_ADC_ADC_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED0_CLK_SYS_CLOCKS |
| // Description : None |
| #define CLOCKS_ENABLED0_CLK_SYS_CLOCKS_RESET _u(0x0) |
| #define CLOCKS_ENABLED0_CLK_SYS_CLOCKS_BITS _u(0x00000001) |
| #define CLOCKS_ENABLED0_CLK_SYS_CLOCKS_MSB _u(0) |
| #define CLOCKS_ENABLED0_CLK_SYS_CLOCKS_LSB _u(0) |
| #define CLOCKS_ENABLED0_CLK_SYS_CLOCKS_ACCESS "RO" |
| // ============================================================================= |
| // Register : CLOCKS_ENABLED1 |
| // Description : indicates the state of the clock enable |
| #define CLOCKS_ENABLED1_OFFSET _u(0x000000b4) |
| #define CLOCKS_ENABLED1_BITS _u(0x00007fff) |
| #define CLOCKS_ENABLED1_RESET _u(0x00000000) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED1_CLK_SYS_XOSC |
| // Description : None |
| #define CLOCKS_ENABLED1_CLK_SYS_XOSC_RESET _u(0x0) |
| #define CLOCKS_ENABLED1_CLK_SYS_XOSC_BITS _u(0x00004000) |
| #define CLOCKS_ENABLED1_CLK_SYS_XOSC_MSB _u(14) |
| #define CLOCKS_ENABLED1_CLK_SYS_XOSC_LSB _u(14) |
| #define CLOCKS_ENABLED1_CLK_SYS_XOSC_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED1_CLK_SYS_XIP |
| // Description : None |
| #define CLOCKS_ENABLED1_CLK_SYS_XIP_RESET _u(0x0) |
| #define CLOCKS_ENABLED1_CLK_SYS_XIP_BITS _u(0x00002000) |
| #define CLOCKS_ENABLED1_CLK_SYS_XIP_MSB _u(13) |
| #define CLOCKS_ENABLED1_CLK_SYS_XIP_LSB _u(13) |
| #define CLOCKS_ENABLED1_CLK_SYS_XIP_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED1_CLK_SYS_WATCHDOG |
| // Description : None |
| #define CLOCKS_ENABLED1_CLK_SYS_WATCHDOG_RESET _u(0x0) |
| #define CLOCKS_ENABLED1_CLK_SYS_WATCHDOG_BITS _u(0x00001000) |
| #define CLOCKS_ENABLED1_CLK_SYS_WATCHDOG_MSB _u(12) |
| #define CLOCKS_ENABLED1_CLK_SYS_WATCHDOG_LSB _u(12) |
| #define CLOCKS_ENABLED1_CLK_SYS_WATCHDOG_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED1_CLK_USB_USBCTRL |
| // Description : None |
| #define CLOCKS_ENABLED1_CLK_USB_USBCTRL_RESET _u(0x0) |
| #define CLOCKS_ENABLED1_CLK_USB_USBCTRL_BITS _u(0x00000800) |
| #define CLOCKS_ENABLED1_CLK_USB_USBCTRL_MSB _u(11) |
| #define CLOCKS_ENABLED1_CLK_USB_USBCTRL_LSB _u(11) |
| #define CLOCKS_ENABLED1_CLK_USB_USBCTRL_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED1_CLK_SYS_USBCTRL |
| // Description : None |
| #define CLOCKS_ENABLED1_CLK_SYS_USBCTRL_RESET _u(0x0) |
| #define CLOCKS_ENABLED1_CLK_SYS_USBCTRL_BITS _u(0x00000400) |
| #define CLOCKS_ENABLED1_CLK_SYS_USBCTRL_MSB _u(10) |
| #define CLOCKS_ENABLED1_CLK_SYS_USBCTRL_LSB _u(10) |
| #define CLOCKS_ENABLED1_CLK_SYS_USBCTRL_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED1_CLK_SYS_UART1 |
| // Description : None |
| #define CLOCKS_ENABLED1_CLK_SYS_UART1_RESET _u(0x0) |
| #define CLOCKS_ENABLED1_CLK_SYS_UART1_BITS _u(0x00000200) |
| #define CLOCKS_ENABLED1_CLK_SYS_UART1_MSB _u(9) |
| #define CLOCKS_ENABLED1_CLK_SYS_UART1_LSB _u(9) |
| #define CLOCKS_ENABLED1_CLK_SYS_UART1_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED1_CLK_PERI_UART1 |
| // Description : None |
| #define CLOCKS_ENABLED1_CLK_PERI_UART1_RESET _u(0x0) |
| #define CLOCKS_ENABLED1_CLK_PERI_UART1_BITS _u(0x00000100) |
| #define CLOCKS_ENABLED1_CLK_PERI_UART1_MSB _u(8) |
| #define CLOCKS_ENABLED1_CLK_PERI_UART1_LSB _u(8) |
| #define CLOCKS_ENABLED1_CLK_PERI_UART1_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED1_CLK_SYS_UART0 |
| // Description : None |
| #define CLOCKS_ENABLED1_CLK_SYS_UART0_RESET _u(0x0) |
| #define CLOCKS_ENABLED1_CLK_SYS_UART0_BITS _u(0x00000080) |
| #define CLOCKS_ENABLED1_CLK_SYS_UART0_MSB _u(7) |
| #define CLOCKS_ENABLED1_CLK_SYS_UART0_LSB _u(7) |
| #define CLOCKS_ENABLED1_CLK_SYS_UART0_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED1_CLK_PERI_UART0 |
| // Description : None |
| #define CLOCKS_ENABLED1_CLK_PERI_UART0_RESET _u(0x0) |
| #define CLOCKS_ENABLED1_CLK_PERI_UART0_BITS _u(0x00000040) |
| #define CLOCKS_ENABLED1_CLK_PERI_UART0_MSB _u(6) |
| #define CLOCKS_ENABLED1_CLK_PERI_UART0_LSB _u(6) |
| #define CLOCKS_ENABLED1_CLK_PERI_UART0_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED1_CLK_SYS_TIMER |
| // Description : None |
| #define CLOCKS_ENABLED1_CLK_SYS_TIMER_RESET _u(0x0) |
| #define CLOCKS_ENABLED1_CLK_SYS_TIMER_BITS _u(0x00000020) |
| #define CLOCKS_ENABLED1_CLK_SYS_TIMER_MSB _u(5) |
| #define CLOCKS_ENABLED1_CLK_SYS_TIMER_LSB _u(5) |
| #define CLOCKS_ENABLED1_CLK_SYS_TIMER_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED1_CLK_SYS_TBMAN |
| // Description : None |
| #define CLOCKS_ENABLED1_CLK_SYS_TBMAN_RESET _u(0x0) |
| #define CLOCKS_ENABLED1_CLK_SYS_TBMAN_BITS _u(0x00000010) |
| #define CLOCKS_ENABLED1_CLK_SYS_TBMAN_MSB _u(4) |
| #define CLOCKS_ENABLED1_CLK_SYS_TBMAN_LSB _u(4) |
| #define CLOCKS_ENABLED1_CLK_SYS_TBMAN_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED1_CLK_SYS_SYSINFO |
| // Description : None |
| #define CLOCKS_ENABLED1_CLK_SYS_SYSINFO_RESET _u(0x0) |
| #define CLOCKS_ENABLED1_CLK_SYS_SYSINFO_BITS _u(0x00000008) |
| #define CLOCKS_ENABLED1_CLK_SYS_SYSINFO_MSB _u(3) |
| #define CLOCKS_ENABLED1_CLK_SYS_SYSINFO_LSB _u(3) |
| #define CLOCKS_ENABLED1_CLK_SYS_SYSINFO_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED1_CLK_SYS_SYSCFG |
| // Description : None |
| #define CLOCKS_ENABLED1_CLK_SYS_SYSCFG_RESET _u(0x0) |
| #define CLOCKS_ENABLED1_CLK_SYS_SYSCFG_BITS _u(0x00000004) |
| #define CLOCKS_ENABLED1_CLK_SYS_SYSCFG_MSB _u(2) |
| #define CLOCKS_ENABLED1_CLK_SYS_SYSCFG_LSB _u(2) |
| #define CLOCKS_ENABLED1_CLK_SYS_SYSCFG_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED1_CLK_SYS_SRAM5 |
| // Description : None |
| #define CLOCKS_ENABLED1_CLK_SYS_SRAM5_RESET _u(0x0) |
| #define CLOCKS_ENABLED1_CLK_SYS_SRAM5_BITS _u(0x00000002) |
| #define CLOCKS_ENABLED1_CLK_SYS_SRAM5_MSB _u(1) |
| #define CLOCKS_ENABLED1_CLK_SYS_SRAM5_LSB _u(1) |
| #define CLOCKS_ENABLED1_CLK_SYS_SRAM5_ACCESS "RO" |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_ENABLED1_CLK_SYS_SRAM4 |
| // Description : None |
| #define CLOCKS_ENABLED1_CLK_SYS_SRAM4_RESET _u(0x0) |
| #define CLOCKS_ENABLED1_CLK_SYS_SRAM4_BITS _u(0x00000001) |
| #define CLOCKS_ENABLED1_CLK_SYS_SRAM4_MSB _u(0) |
| #define CLOCKS_ENABLED1_CLK_SYS_SRAM4_LSB _u(0) |
| #define CLOCKS_ENABLED1_CLK_SYS_SRAM4_ACCESS "RO" |
| // ============================================================================= |
| // Register : CLOCKS_INTR |
| // Description : Raw Interrupts |
| #define CLOCKS_INTR_OFFSET _u(0x000000b8) |
| #define CLOCKS_INTR_BITS _u(0x00000001) |
| #define CLOCKS_INTR_RESET _u(0x00000000) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_INTR_CLK_SYS_RESUS |
| // Description : None |
| #define CLOCKS_INTR_CLK_SYS_RESUS_RESET _u(0x0) |
| #define CLOCKS_INTR_CLK_SYS_RESUS_BITS _u(0x00000001) |
| #define CLOCKS_INTR_CLK_SYS_RESUS_MSB _u(0) |
| #define CLOCKS_INTR_CLK_SYS_RESUS_LSB _u(0) |
| #define CLOCKS_INTR_CLK_SYS_RESUS_ACCESS "RO" |
| // ============================================================================= |
| // Register : CLOCKS_INTE |
| // Description : Interrupt Enable |
| #define CLOCKS_INTE_OFFSET _u(0x000000bc) |
| #define CLOCKS_INTE_BITS _u(0x00000001) |
| #define CLOCKS_INTE_RESET _u(0x00000000) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_INTE_CLK_SYS_RESUS |
| // Description : None |
| #define CLOCKS_INTE_CLK_SYS_RESUS_RESET _u(0x0) |
| #define CLOCKS_INTE_CLK_SYS_RESUS_BITS _u(0x00000001) |
| #define CLOCKS_INTE_CLK_SYS_RESUS_MSB _u(0) |
| #define CLOCKS_INTE_CLK_SYS_RESUS_LSB _u(0) |
| #define CLOCKS_INTE_CLK_SYS_RESUS_ACCESS "RW" |
| // ============================================================================= |
| // Register : CLOCKS_INTF |
| // Description : Interrupt Force |
| #define CLOCKS_INTF_OFFSET _u(0x000000c0) |
| #define CLOCKS_INTF_BITS _u(0x00000001) |
| #define CLOCKS_INTF_RESET _u(0x00000000) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_INTF_CLK_SYS_RESUS |
| // Description : None |
| #define CLOCKS_INTF_CLK_SYS_RESUS_RESET _u(0x0) |
| #define CLOCKS_INTF_CLK_SYS_RESUS_BITS _u(0x00000001) |
| #define CLOCKS_INTF_CLK_SYS_RESUS_MSB _u(0) |
| #define CLOCKS_INTF_CLK_SYS_RESUS_LSB _u(0) |
| #define CLOCKS_INTF_CLK_SYS_RESUS_ACCESS "RW" |
| // ============================================================================= |
| // Register : CLOCKS_INTS |
| // Description : Interrupt status after masking & forcing |
| #define CLOCKS_INTS_OFFSET _u(0x000000c4) |
| #define CLOCKS_INTS_BITS _u(0x00000001) |
| #define CLOCKS_INTS_RESET _u(0x00000000) |
| // ----------------------------------------------------------------------------- |
| // Field : CLOCKS_INTS_CLK_SYS_RESUS |
| // Description : None |
| #define CLOCKS_INTS_CLK_SYS_RESUS_RESET _u(0x0) |
| #define CLOCKS_INTS_CLK_SYS_RESUS_BITS _u(0x00000001) |
| #define CLOCKS_INTS_CLK_SYS_RESUS_MSB _u(0) |
| #define CLOCKS_INTS_CLK_SYS_RESUS_LSB _u(0) |
| #define CLOCKS_INTS_CLK_SYS_RESUS_ACCESS "RO" |
| // ============================================================================= |
| #endif // HARDWARE_REGS_CLOCKS_DEFINED |
