| /* |
| * Copyright (c) 2020 Raspberry Pi (Trading) Ltd. |
| * |
| * SPDX-License-Identifier: BSD-3-Clause |
| */ |
| |
| // ----------------------------------------------------- |
| // NOTE: THIS HEADER IS ALSO INCLUDED BY ASSEMBLER SO |
| // SHOULD ONLY CONSIST OF PREPROCESSOR DIRECTIVES |
| // ----------------------------------------------------- |
| |
| // pico_cmake_set PICO_PLATFORM=rp2040 |
| |
| #ifndef _BOARDS_GARATRONIC_PYBSTICK26_RP2040_H |
| #define _BOARDS_GARATRONIC_PYBSTICK26_RP2040_H |
| |
| // For board detection |
| #define GARATRONIC_PYBSTICK26_RP2040 |
| |
| // --- UART --- |
| #ifndef PICO_DEFAULT_UART |
| #define PICO_DEFAULT_UART 0 |
| #endif |
| #ifndef PICO_DEFAULT_UART_TX_PIN |
| #define PICO_DEFAULT_UART_TX_PIN 0 |
| #endif |
| #ifndef PICO_DEFAULT_UART_RX_PIN |
| #define PICO_DEFAULT_UART_RX_PIN 1 |
| #endif |
| |
| // --- LED --- |
| #ifndef PICO_DEFAULT_LED_PIN |
| #define PICO_DEFAULT_LED_PIN 23 |
| #endif |
| // no PICO_DEFAULT_WS2812_PIN |
| |
| // --- I2C --- |
| #ifndef PICO_DEFAULT_I2C |
| #define PICO_DEFAULT_I2C 1 |
| #endif |
| #ifndef PICO_DEFAULT_I2C_SDA_PIN |
| #define PICO_DEFAULT_I2C_SDA_PIN 6 |
| #endif |
| #ifndef PICO_DEFAULT_I2C_SCL_PIN |
| #define PICO_DEFAULT_I2C_SCL_PIN 7 |
| #endif |
| |
| // --- SPI --- |
| #ifndef PICO_DEFAULT_SPI |
| #define PICO_DEFAULT_SPI 1 |
| #endif |
| #ifndef PICO_DEFAULT_SPI_SCK_PIN |
| #define PICO_DEFAULT_SPI_SCK_PIN 10 |
| #endif |
| #ifndef PICO_DEFAULT_SPI_TX_PIN |
| #define PICO_DEFAULT_SPI_TX_PIN 11 |
| #endif |
| #ifndef PICO_DEFAULT_SPI_RX_PIN |
| #define PICO_DEFAULT_SPI_RX_PIN 8 |
| #endif |
| #ifndef PICO_DEFAULT_SPI_CSN_PIN |
| #define PICO_DEFAULT_SPI_CSN_PIN 9 |
| #endif |
| |
| // --- FLASH --- |
| |
| #define PICO_BOOT_STAGE2_CHOOSE_W25Q080 1 |
| |
| #ifndef PICO_FLASH_SPI_CLKDIV |
| #define PICO_FLASH_SPI_CLKDIV 2 |
| #endif |
| |
| // pico_cmake_set_default PICO_FLASH_SIZE_BYTES = (1 * 1024 * 1024) |
| #ifndef PICO_FLASH_SIZE_BYTES |
| #define PICO_FLASH_SIZE_BYTES (1 * 1024 * 1024) |
| #endif |
| // Drive high to force power supply into PWM mode (lower ripple on 3V3 at light loads) |
| // Linear regulator on Pybstick26 |
| //#define PICO_SMPS_MODE_PIN 23 |
| |
| // All boards have B1 RP2040 |
| #ifndef PICO_RP2040_B0_SUPPORTED |
| #define PICO_RP2040_B0_SUPPORTED 0 |
| #endif |
| |
| #endif |
| // of #define _BOARDS_GARATRONIC_PYBSTICK26_RP2040_H |