blob: 7309f53bd4e5b64733d72bca5ca9cc65f359e3f7 [file] [log] [blame]
// ----------------------------------------------------------------------------
// Second stage boot code
// Copyright (c) 2019-2021 Raspberry Pi (Trading) Ltd.
// SPDX-License-Identifier: BSD-3-Clause
//
// Device: Winbond W25Q080
// Also supports W25Q16JV (which has some different SR instructions)
// Also supports AT25SF081
// Also supports S25FL132K0
//
// Description: Configures W25Q080 to run in Quad I/O continuous read XIP mode
//
// Details: * Check status register 2 to determine if QSPI mode is enabled,
// and perform an SR2 programming cycle if necessary.
// * Use SSI to perform a dummy 0xEB read command, with the mode
// continuation bits set, so that the flash will not require
// 0xEB instruction prefix on subsequent reads.
// * Configure SSI to write address, mode bits, but no instruction.
// SSI + flash are now jointly in a state where continuous reads
// can take place.
// * Jump to exit pointer passed in via lr. Bootrom passes null,
// in which case this code uses a default 256 byte flash offset
//
// Building: * This code must be position-independent, and use stack only
// * The code will be padded to a size of 256 bytes, including a
// 4-byte checksum. Therefore code size cannot exceed 252 bytes.
// ----------------------------------------------------------------------------
#include "pico/asm_helper.S"
#include "hardware/regs/addressmap.h"
#include "hardware/regs/ssi.h"
#include "hardware/regs/pads_qspi.h"
// ----------------------------------------------------------------------------
// Config section
// ----------------------------------------------------------------------------
// It should be possible to support most flash devices by modifying this section
// The serial flash interface will run at clk_sys/PICO_FLASH_SPI_CLKDIV.
// This must be a positive, even integer.
// The bootrom is very conservative with SPI frequency, but here we should be
// as aggressive as possible.
#ifndef PICO_FLASH_SPI_CLKDIV
#define PICO_FLASH_SPI_CLKDIV 4
#endif
#if PICO_FLASH_SPI_CLKDIV & 1
#error PICO_FLASH_SPI_CLKDIV must be even
#endif
// Define interface width: single/dual/quad IO
#define FRAME_FORMAT SSI_CTRLR0_SPI_FRF_VALUE_QUAD
// For W25Q080 this is the "Read data fast quad IO" instruction:
#define CMD_READ 0xeb
// "Mode bits" are 8 special bits sent immediately after
// the address bits in a "Read Data Fast Quad I/O" command sequence.
// On W25Q080, the four LSBs are don't care, and if MSBs == 0xa, the
// next read does not require the 0xeb instruction prefix.
#define MODE_CONTINUOUS_READ 0xa0
// The number of address + mode bits, divided by 4 (always 4, not function of
// interface width).
#define ADDR_L 8
// How many clocks of Hi-Z following the mode bits. For W25Q080, 4 dummy cycles
// are required.
#define WAIT_CYCLES 4
// If defined, we will read status reg, compare to SREG_DATA, and overwrite
// with our value if the SR doesn't match.
// We do a two-byte write to SR1 (01h cmd) rather than a one-byte write to
// SR2 (31h cmd) as the latter command isn't supported by WX25Q080.
// This isn't great because it will remove block protections.
// A better solution is to use a volatile SR write if your device supports it.
#define PROGRAM_STATUS_REG
#define CMD_WRITE_ENABLE 0x06
#define CMD_READ_STATUS 0x05
#define CMD_READ_STATUS2 0x35
#define CMD_WRITE_STATUS 0x01
#define SREG_DATA 0x02 // Enable quad-SPI mode
// ----------------------------------------------------------------------------
// Start of 2nd Stage Boot Code
// ----------------------------------------------------------------------------
pico_default_asm_setup
.section .text
// The exit point is passed in lr. If entered from bootrom, this will be the
// flash address immediately following this second stage (0x10000100).
// Otherwise it will be a return address -- second stage being called as a
// function by user code, after copying out of XIP region. r3 holds SSI base,
// r0...2 used as temporaries. Other GPRs not used.
regular_func _stage2_boot
push {lr}
// Set pad configuration:
// - SCLK 8mA drive, no slew limiting
// - SDx disable input Schmitt to reduce delay
ldr r3, =PADS_QSPI_BASE
movs r0, #(2 << PADS_QSPI_GPIO_QSPI_SCLK_DRIVE_LSB | PADS_QSPI_GPIO_QSPI_SCLK_SLEWFAST_BITS)
str r0, [r3, #PADS_QSPI_GPIO_QSPI_SCLK_OFFSET]
ldr r0, [r3, #PADS_QSPI_GPIO_QSPI_SD0_OFFSET]
movs r1, #PADS_QSPI_GPIO_QSPI_SD0_SCHMITT_BITS
bics r0, r1
str r0, [r3, #PADS_QSPI_GPIO_QSPI_SD0_OFFSET]
str r0, [r3, #PADS_QSPI_GPIO_QSPI_SD1_OFFSET]
str r0, [r3, #PADS_QSPI_GPIO_QSPI_SD2_OFFSET]
str r0, [r3, #PADS_QSPI_GPIO_QSPI_SD3_OFFSET]
ldr r3, =XIP_SSI_BASE
// Disable SSI to allow further config
movs r1, #0
str r1, [r3, #SSI_SSIENR_OFFSET]
// Set baud rate
movs r1, #PICO_FLASH_SPI_CLKDIV
str r1, [r3, #SSI_BAUDR_OFFSET]
// Set 1-cycle sample delay. If PICO_FLASH_SPI_CLKDIV == 2 then this means,
// if the flash launches data on SCLK posedge, we capture it at the time that
// the next SCLK posedge is launched. This is shortly before that posedge
// arrives at the flash, so data hold time should be ok. For
// PICO_FLASH_SPI_CLKDIV > 2 this pretty much has no effect.
movs r1, #1
movs r2, #SSI_RX_SAMPLE_DLY_OFFSET // == 0xf0 so need 8 bits of offset significance
str r1, [r3, r2]
// On QSPI parts we usually need a 01h SR-write command to enable QSPI mode
// (i.e. turn WPn and HOLDn into IO2/IO3)
#ifdef PROGRAM_STATUS_REG
program_sregs:
#define CTRL0_SPI_TXRX \
(7 << SSI_CTRLR0_DFS_32_LSB) | /* 8 bits per data frame */ \
(SSI_CTRLR0_TMOD_VALUE_TX_AND_RX << SSI_CTRLR0_TMOD_LSB)
ldr r1, =(CTRL0_SPI_TXRX)
str r1, [r3, #SSI_CTRLR0_OFFSET]
// Enable SSI and select slave 0
movs r1, #1
str r1, [r3, #SSI_SSIENR_OFFSET]
// Check whether SR needs updating
movs r0, #CMD_READ_STATUS2
bl read_flash_sreg
movs r2, #SREG_DATA
cmp r0, r2
beq skip_sreg_programming
// Send write enable command
movs r1, #CMD_WRITE_ENABLE
str r1, [r3, #SSI_DR0_OFFSET]
// Poll for completion and discard RX
bl wait_ssi_ready
ldr r1, [r3, #SSI_DR0_OFFSET]
// Send status write command followed by data bytes
movs r1, #CMD_WRITE_STATUS
str r1, [r3, #SSI_DR0_OFFSET]
movs r0, #0
str r0, [r3, #SSI_DR0_OFFSET]
str r2, [r3, #SSI_DR0_OFFSET]
bl wait_ssi_ready
ldr r1, [r3, #SSI_DR0_OFFSET]
ldr r1, [r3, #SSI_DR0_OFFSET]
ldr r1, [r3, #SSI_DR0_OFFSET]
// Poll status register for write completion
1:
movs r0, #CMD_READ_STATUS
bl read_flash_sreg
movs r1, #1
tst r0, r1
bne 1b
skip_sreg_programming:
// Disable SSI again so that it can be reconfigured
movs r1, #0
str r1, [r3, #SSI_SSIENR_OFFSET]
#endif
// Currently the flash expects an 8 bit serial command prefix on every
// transfer, which is a waste of cycles. Perform a dummy Fast Read Quad I/O
// command, with mode bits set such that the flash will not expect a serial
// command prefix on *subsequent* transfers. We don't care about the results
// of the read, the important part is the mode bits.
dummy_read:
#define CTRLR0_ENTER_XIP \
(FRAME_FORMAT /* Quad I/O mode */ \
<< SSI_CTRLR0_SPI_FRF_LSB) | \
(31 << SSI_CTRLR0_DFS_32_LSB) | /* 32 data bits */ \
(SSI_CTRLR0_TMOD_VALUE_EEPROM_READ /* Send INST/ADDR, Receive Data */ \
<< SSI_CTRLR0_TMOD_LSB)
ldr r1, =(CTRLR0_ENTER_XIP)
str r1, [r3, #SSI_CTRLR0_OFFSET]
movs r1, #0x0 // NDF=0 (single 32b read)
str r1, [r3, #SSI_CTRLR1_OFFSET]
#define SPI_CTRLR0_ENTER_XIP \
(ADDR_L << SSI_SPI_CTRLR0_ADDR_L_LSB) | /* Address + mode bits */ \
(WAIT_CYCLES << SSI_SPI_CTRLR0_WAIT_CYCLES_LSB) | /* Hi-Z dummy clocks following address + mode */ \
(SSI_SPI_CTRLR0_INST_L_VALUE_8B \
<< SSI_SPI_CTRLR0_INST_L_LSB) | /* 8-bit instruction */ \
(SSI_SPI_CTRLR0_TRANS_TYPE_VALUE_1C2A /* Send Command in serial mode then address in Quad I/O mode */ \
<< SSI_SPI_CTRLR0_TRANS_TYPE_LSB)
ldr r1, =(SPI_CTRLR0_ENTER_XIP)
ldr r0, =(XIP_SSI_BASE + SSI_SPI_CTRLR0_OFFSET) // SPI_CTRL0 Register
str r1, [r0]
movs r1, #1 // Re-enable SSI
str r1, [r3, #SSI_SSIENR_OFFSET]
movs r1, #CMD_READ
str r1, [r3, #SSI_DR0_OFFSET] // Push SPI command into TX FIFO
movs r1, #MODE_CONTINUOUS_READ // 32-bit: 24 address bits (we don't care, so 0) and M[7:4]=1010
str r1, [r3, #SSI_DR0_OFFSET] // Push Address into TX FIFO - this will trigger the transaction
// Poll for completion
bl wait_ssi_ready
// The flash is in a state where we can blast addresses in parallel, and get
// parallel data back. Now configure the SSI to translate XIP bus accesses
// into QSPI transfers of this form.
movs r1, #0
str r1, [r3, #SSI_SSIENR_OFFSET] // Disable SSI (and clear FIFO) to allow further config
// Note that the INST_L field is used to select what XIP data gets pushed into
// the TX FIFO:
// INST_L_0_BITS {ADDR[23:0],XIP_CMD[7:0]} Load "mode bits" into XIP_CMD
// Anything else {XIP_CMD[7:0],ADDR[23:0]} Load SPI command into XIP_CMD
configure_ssi:
#define SPI_CTRLR0_XIP \
(MODE_CONTINUOUS_READ /* Mode bits to keep flash in continuous read mode */ \
<< SSI_SPI_CTRLR0_XIP_CMD_LSB) | \
(ADDR_L << SSI_SPI_CTRLR0_ADDR_L_LSB) | /* Total number of address + mode bits */ \
(WAIT_CYCLES << SSI_SPI_CTRLR0_WAIT_CYCLES_LSB) | /* Hi-Z dummy clocks following address + mode */ \
(SSI_SPI_CTRLR0_INST_L_VALUE_NONE /* Do not send a command, instead send XIP_CMD as mode bits after address */ \
<< SSI_SPI_CTRLR0_INST_L_LSB) | \
(SSI_SPI_CTRLR0_TRANS_TYPE_VALUE_2C2A /* Send Address in Quad I/O mode (and Command but that is zero bits long) */ \
<< SSI_SPI_CTRLR0_TRANS_TYPE_LSB)
ldr r1, =(SPI_CTRLR0_XIP)
ldr r0, =(XIP_SSI_BASE + SSI_SPI_CTRLR0_OFFSET)
str r1, [r0]
movs r1, #1
str r1, [r3, #SSI_SSIENR_OFFSET] // Re-enable SSI
// Bus accesses to the XIP window will now be transparently serviced by the
// external flash on cache miss. We are ready to run code from flash.
// Pull in standard exit routine
#include "boot2_helpers/exit_from_boot2.S"
// Common functions
#include "boot2_helpers/wait_ssi_ready.S"
#ifdef PROGRAM_STATUS_REG
#include "boot2_helpers/read_flash_sreg.S"
#endif
.global literals
literals:
.ltorg
.end