| // THIS HEADER FILE IS AUTOMATICALLY GENERATED -- DO NOT EDIT |
| |
| /* |
| * Copyright (c) 2021 Raspberry Pi (Trading) Ltd. |
| * |
| * SPDX-License-Identifier: BSD-3-Clause |
| */ |
| |
| #ifndef _HARDWARE_STRUCTS_I2C_H |
| #define _HARDWARE_STRUCTS_I2C_H |
| |
| #include "hardware/address_mapped.h" |
| #include "hardware/regs/i2c.h" |
| |
| // Reference to datasheet: https://datasheets.raspberrypi.com/rp2040/rp2040-datasheet.pdf#tab-registerlist_i2c |
| // |
| // The _REG_ macro is intended to help make the register navigable in your IDE (for example, using the "Go to Definition" feature) |
| // _REG_(x) will link to the corresponding register in hardware/regs/i2c.h. |
| // |
| // Bit-field descriptions are of the form: |
| // BITMASK [BITRANGE]: FIELDNAME (RESETVALUE): DESCRIPTION |
| |
| typedef struct { |
| _REG_(I2C_IC_CON_OFFSET) // I2C_IC_CON |
| // I2C Control Register |
| // 0x00000400 [10] : STOP_DET_IF_MASTER_ACTIVE (0): Master issues the STOP_DET interrupt irrespective of whether... |
| // 0x00000200 [9] : RX_FIFO_FULL_HLD_CTRL (0): This bit controls whether DW_apb_i2c should hold the bus when the Rx... |
| // 0x00000100 [8] : TX_EMPTY_CTRL (0): This bit controls the generation of the TX_EMPTY interrupt, as described in... |
| // 0x00000080 [7] : STOP_DET_IFADDRESSED (0): In slave mode: - 1'b1: issues the STOP_DET interrupt only when it is... |
| // 0x00000040 [6] : IC_SLAVE_DISABLE (1): This bit controls whether I2C has its slave disabled, which means once... |
| // 0x00000020 [5] : IC_RESTART_EN (1): Determines whether RESTART conditions may be sent when acting as a master |
| // 0x00000010 [4] : IC_10BITADDR_MASTER (0): Controls whether the DW_apb_i2c starts its transfers in 7- or 10-bit... |
| // 0x00000008 [3] : IC_10BITADDR_SLAVE (0): When acting as a slave, this bit controls whether the DW_apb_i2c... |
| // 0x00000006 [2:1] : SPEED (0x2): These bits control at which speed the DW_apb_i2c operates; its setting is relevant... |
| // 0x00000001 [0] : MASTER_MODE (1): This bit controls whether the DW_apb_i2c master is enabled |
| io_rw_32 con; |
| |
| _REG_(I2C_IC_TAR_OFFSET) // I2C_IC_TAR |
| // I2C Target Address Register |
| // 0x00000800 [11] : SPECIAL (0): This bit indicates whether software performs a Device-ID or General Call or START... |
| // 0x00000400 [10] : GC_OR_START (0): If bit 11 (SPECIAL) is set to 1 and bit 13(Device-ID) is set to 0, then this... |
| // 0x000003ff [9:0] : IC_TAR (0x55): This is the target address for any master transaction |
| io_rw_32 tar; |
| |
| _REG_(I2C_IC_SAR_OFFSET) // I2C_IC_SAR |
| // I2C Slave Address Register |
| // 0x000003ff [9:0] : IC_SAR (0x55): The IC_SAR holds the slave address when the I2C is operating as a slave |
| io_rw_32 sar; |
| |
| uint32_t _pad0; |
| |
| _REG_(I2C_IC_DATA_CMD_OFFSET) // I2C_IC_DATA_CMD |
| // I2C Rx/Tx Data Buffer and Command Register; this is the register the CPU writes to when filling the TX FIFO and the... |
| // 0x00000800 [11] : FIRST_DATA_BYTE (0): Indicates the first data byte received after the address phase for receive... |
| // 0x00000400 [10] : RESTART (0): This bit controls whether a RESTART is issued before the byte is sent or received |
| // 0x00000200 [9] : STOP (0): This bit controls whether a STOP is issued after the byte is sent or received |
| // 0x00000100 [8] : CMD (0): This bit controls whether a read or a write is performed |
| // 0x000000ff [7:0] : DAT (0): This register contains the data to be transmitted or received on the I2C bus |
| io_rw_32 data_cmd; |
| |
| _REG_(I2C_IC_SS_SCL_HCNT_OFFSET) // I2C_IC_SS_SCL_HCNT |
| // Standard Speed I2C Clock SCL High Count Register |
| // 0x0000ffff [15:0] : IC_SS_SCL_HCNT (0x28): This register must be set before any I2C bus transaction can take place... |
| io_rw_32 ss_scl_hcnt; |
| |
| _REG_(I2C_IC_SS_SCL_LCNT_OFFSET) // I2C_IC_SS_SCL_LCNT |
| // Standard Speed I2C Clock SCL Low Count Register |
| // 0x0000ffff [15:0] : IC_SS_SCL_LCNT (0x2f): This register must be set before any I2C bus transaction can take place... |
| io_rw_32 ss_scl_lcnt; |
| |
| _REG_(I2C_IC_FS_SCL_HCNT_OFFSET) // I2C_IC_FS_SCL_HCNT |
| // Fast Mode or Fast Mode Plus I2C Clock SCL High Count Register |
| // 0x0000ffff [15:0] : IC_FS_SCL_HCNT (0x6): This register must be set before any I2C bus transaction can take place... |
| io_rw_32 fs_scl_hcnt; |
| |
| _REG_(I2C_IC_FS_SCL_LCNT_OFFSET) // I2C_IC_FS_SCL_LCNT |
| // Fast Mode or Fast Mode Plus I2C Clock SCL Low Count Register |
| // 0x0000ffff [15:0] : IC_FS_SCL_LCNT (0xd): This register must be set before any I2C bus transaction can take place... |
| io_rw_32 fs_scl_lcnt; |
| |
| uint32_t _pad1[2]; |
| |
| _REG_(I2C_IC_INTR_STAT_OFFSET) // I2C_IC_INTR_STAT |
| // I2C Interrupt Status Register |
| // 0x00001000 [12] : R_RESTART_DET (0): See IC_RAW_INTR_STAT for a detailed description of R_RESTART_DET bit |
| // 0x00000800 [11] : R_GEN_CALL (0): See IC_RAW_INTR_STAT for a detailed description of R_GEN_CALL bit |
| // 0x00000400 [10] : R_START_DET (0): See IC_RAW_INTR_STAT for a detailed description of R_START_DET bit |
| // 0x00000200 [9] : R_STOP_DET (0): See IC_RAW_INTR_STAT for a detailed description of R_STOP_DET bit |
| // 0x00000100 [8] : R_ACTIVITY (0): See IC_RAW_INTR_STAT for a detailed description of R_ACTIVITY bit |
| // 0x00000080 [7] : R_RX_DONE (0): See IC_RAW_INTR_STAT for a detailed description of R_RX_DONE bit |
| // 0x00000040 [6] : R_TX_ABRT (0): See IC_RAW_INTR_STAT for a detailed description of R_TX_ABRT bit |
| // 0x00000020 [5] : R_RD_REQ (0): See IC_RAW_INTR_STAT for a detailed description of R_RD_REQ bit |
| // 0x00000010 [4] : R_TX_EMPTY (0): See IC_RAW_INTR_STAT for a detailed description of R_TX_EMPTY bit |
| // 0x00000008 [3] : R_TX_OVER (0): See IC_RAW_INTR_STAT for a detailed description of R_TX_OVER bit |
| // 0x00000004 [2] : R_RX_FULL (0): See IC_RAW_INTR_STAT for a detailed description of R_RX_FULL bit |
| // 0x00000002 [1] : R_RX_OVER (0): See IC_RAW_INTR_STAT for a detailed description of R_RX_OVER bit |
| // 0x00000001 [0] : R_RX_UNDER (0): See IC_RAW_INTR_STAT for a detailed description of R_RX_UNDER bit |
| io_ro_32 intr_stat; |
| |
| _REG_(I2C_IC_INTR_MASK_OFFSET) // I2C_IC_INTR_MASK |
| // I2C Interrupt Mask Register |
| // 0x00001000 [12] : M_RESTART_DET (0): This bit masks the R_RESTART_DET interrupt in IC_INTR_STAT register |
| // 0x00000800 [11] : M_GEN_CALL (1): This bit masks the R_GEN_CALL interrupt in IC_INTR_STAT register |
| // 0x00000400 [10] : M_START_DET (0): This bit masks the R_START_DET interrupt in IC_INTR_STAT register |
| // 0x00000200 [9] : M_STOP_DET (0): This bit masks the R_STOP_DET interrupt in IC_INTR_STAT register |
| // 0x00000100 [8] : M_ACTIVITY (0): This bit masks the R_ACTIVITY interrupt in IC_INTR_STAT register |
| // 0x00000080 [7] : M_RX_DONE (1): This bit masks the R_RX_DONE interrupt in IC_INTR_STAT register |
| // 0x00000040 [6] : M_TX_ABRT (1): This bit masks the R_TX_ABRT interrupt in IC_INTR_STAT register |
| // 0x00000020 [5] : M_RD_REQ (1): This bit masks the R_RD_REQ interrupt in IC_INTR_STAT register |
| // 0x00000010 [4] : M_TX_EMPTY (1): This bit masks the R_TX_EMPTY interrupt in IC_INTR_STAT register |
| // 0x00000008 [3] : M_TX_OVER (1): This bit masks the R_TX_OVER interrupt in IC_INTR_STAT register |
| // 0x00000004 [2] : M_RX_FULL (1): This bit masks the R_RX_FULL interrupt in IC_INTR_STAT register |
| // 0x00000002 [1] : M_RX_OVER (1): This bit masks the R_RX_OVER interrupt in IC_INTR_STAT register |
| // 0x00000001 [0] : M_RX_UNDER (1): This bit masks the R_RX_UNDER interrupt in IC_INTR_STAT register |
| io_rw_32 intr_mask; |
| |
| _REG_(I2C_IC_RAW_INTR_STAT_OFFSET) // I2C_IC_RAW_INTR_STAT |
| // I2C Raw Interrupt Status Register |
| // 0x00001000 [12] : RESTART_DET (0): Indicates whether a RESTART condition has occurred on the I2C interface when... |
| // 0x00000800 [11] : GEN_CALL (0): Set only when a General Call address is received and it is acknowledged |
| // 0x00000400 [10] : START_DET (0): Indicates whether a START or RESTART condition has occurred on the I2C interface... |
| // 0x00000200 [9] : STOP_DET (0): Indicates whether a STOP condition has occurred on the I2C interface regardless... |
| // 0x00000100 [8] : ACTIVITY (0): This bit captures DW_apb_i2c activity and stays set until it is cleared |
| // 0x00000080 [7] : RX_DONE (0): When the DW_apb_i2c is acting as a slave-transmitter, this bit is set to 1 if the... |
| // 0x00000040 [6] : TX_ABRT (0): This bit indicates if DW_apb_i2c, as an I2C transmitter, is unable to complete the... |
| // 0x00000020 [5] : RD_REQ (0): This bit is set to 1 when DW_apb_i2c is acting as a slave and another I2C master is... |
| // 0x00000010 [4] : TX_EMPTY (0): The behavior of the TX_EMPTY interrupt status differs based on the TX_EMPTY_CTRL... |
| // 0x00000008 [3] : TX_OVER (0): Set during transmit if the transmit buffer is filled to IC_TX_BUFFER_DEPTH and the... |
| // 0x00000004 [2] : RX_FULL (0): Set when the receive buffer reaches or goes above the RX_TL threshold in the... |
| // 0x00000002 [1] : RX_OVER (0): Set if the receive buffer is completely filled to IC_RX_BUFFER_DEPTH and an... |
| // 0x00000001 [0] : RX_UNDER (0): Set if the processor attempts to read the receive buffer when it is empty by... |
| io_ro_32 raw_intr_stat; |
| |
| _REG_(I2C_IC_RX_TL_OFFSET) // I2C_IC_RX_TL |
| // I2C Receive FIFO Threshold Register |
| // 0x000000ff [7:0] : RX_TL (0): Receive FIFO Threshold Level |
| io_rw_32 rx_tl; |
| |
| _REG_(I2C_IC_TX_TL_OFFSET) // I2C_IC_TX_TL |
| // I2C Transmit FIFO Threshold Register |
| // 0x000000ff [7:0] : TX_TL (0): Transmit FIFO Threshold Level |
| io_rw_32 tx_tl; |
| |
| _REG_(I2C_IC_CLR_INTR_OFFSET) // I2C_IC_CLR_INTR |
| // Clear Combined and Individual Interrupt Register |
| // 0x00000001 [0] : CLR_INTR (0): Read this register to clear the combined interrupt, all individual interrupts,... |
| io_ro_32 clr_intr; |
| |
| _REG_(I2C_IC_CLR_RX_UNDER_OFFSET) // I2C_IC_CLR_RX_UNDER |
| // Clear RX_UNDER Interrupt Register |
| // 0x00000001 [0] : CLR_RX_UNDER (0): Read this register to clear the RX_UNDER interrupt (bit 0) of the... |
| io_ro_32 clr_rx_under; |
| |
| _REG_(I2C_IC_CLR_RX_OVER_OFFSET) // I2C_IC_CLR_RX_OVER |
| // Clear RX_OVER Interrupt Register |
| // 0x00000001 [0] : CLR_RX_OVER (0): Read this register to clear the RX_OVER interrupt (bit 1) of the... |
| io_ro_32 clr_rx_over; |
| |
| _REG_(I2C_IC_CLR_TX_OVER_OFFSET) // I2C_IC_CLR_TX_OVER |
| // Clear TX_OVER Interrupt Register |
| // 0x00000001 [0] : CLR_TX_OVER (0): Read this register to clear the TX_OVER interrupt (bit 3) of the... |
| io_ro_32 clr_tx_over; |
| |
| _REG_(I2C_IC_CLR_RD_REQ_OFFSET) // I2C_IC_CLR_RD_REQ |
| // Clear RD_REQ Interrupt Register |
| // 0x00000001 [0] : CLR_RD_REQ (0): Read this register to clear the RD_REQ interrupt (bit 5) of the... |
| io_ro_32 clr_rd_req; |
| |
| _REG_(I2C_IC_CLR_TX_ABRT_OFFSET) // I2C_IC_CLR_TX_ABRT |
| // Clear TX_ABRT Interrupt Register |
| // 0x00000001 [0] : CLR_TX_ABRT (0): Read this register to clear the TX_ABRT interrupt (bit 6) of the... |
| io_ro_32 clr_tx_abrt; |
| |
| _REG_(I2C_IC_CLR_RX_DONE_OFFSET) // I2C_IC_CLR_RX_DONE |
| // Clear RX_DONE Interrupt Register |
| // 0x00000001 [0] : CLR_RX_DONE (0): Read this register to clear the RX_DONE interrupt (bit 7) of the... |
| io_ro_32 clr_rx_done; |
| |
| _REG_(I2C_IC_CLR_ACTIVITY_OFFSET) // I2C_IC_CLR_ACTIVITY |
| // Clear ACTIVITY Interrupt Register |
| // 0x00000001 [0] : CLR_ACTIVITY (0): Reading this register clears the ACTIVITY interrupt if the I2C is not active anymore |
| io_ro_32 clr_activity; |
| |
| _REG_(I2C_IC_CLR_STOP_DET_OFFSET) // I2C_IC_CLR_STOP_DET |
| // Clear STOP_DET Interrupt Register |
| // 0x00000001 [0] : CLR_STOP_DET (0): Read this register to clear the STOP_DET interrupt (bit 9) of the... |
| io_ro_32 clr_stop_det; |
| |
| _REG_(I2C_IC_CLR_START_DET_OFFSET) // I2C_IC_CLR_START_DET |
| // Clear START_DET Interrupt Register |
| // 0x00000001 [0] : CLR_START_DET (0): Read this register to clear the START_DET interrupt (bit 10) of the... |
| io_ro_32 clr_start_det; |
| |
| _REG_(I2C_IC_CLR_GEN_CALL_OFFSET) // I2C_IC_CLR_GEN_CALL |
| // Clear GEN_CALL Interrupt Register |
| // 0x00000001 [0] : CLR_GEN_CALL (0): Read this register to clear the GEN_CALL interrupt (bit 11) of... |
| io_ro_32 clr_gen_call; |
| |
| _REG_(I2C_IC_ENABLE_OFFSET) // I2C_IC_ENABLE |
| // I2C Enable Register |
| // 0x00000004 [2] : TX_CMD_BLOCK (0): In Master mode: - 1'b1: Blocks the transmission of data on I2C bus even if Tx... |
| // 0x00000002 [1] : ABORT (0): When set, the controller initiates the transfer abort |
| // 0x00000001 [0] : ENABLE (0): Controls whether the DW_apb_i2c is enabled |
| io_rw_32 enable; |
| |
| _REG_(I2C_IC_STATUS_OFFSET) // I2C_IC_STATUS |
| // I2C Status Register |
| // 0x00000040 [6] : SLV_ACTIVITY (0): Slave FSM Activity Status |
| // 0x00000020 [5] : MST_ACTIVITY (0): Master FSM Activity Status |
| // 0x00000010 [4] : RFF (0): Receive FIFO Completely Full |
| // 0x00000008 [3] : RFNE (0): Receive FIFO Not Empty |
| // 0x00000004 [2] : TFE (1): Transmit FIFO Completely Empty |
| // 0x00000002 [1] : TFNF (1): Transmit FIFO Not Full |
| // 0x00000001 [0] : ACTIVITY (0): I2C Activity Status |
| io_ro_32 status; |
| |
| _REG_(I2C_IC_TXFLR_OFFSET) // I2C_IC_TXFLR |
| // I2C Transmit FIFO Level Register This register contains the number of valid data entries in the transmit FIFO buffer |
| // 0x0000001f [4:0] : TXFLR (0): Transmit FIFO Level |
| io_ro_32 txflr; |
| |
| _REG_(I2C_IC_RXFLR_OFFSET) // I2C_IC_RXFLR |
| // I2C Receive FIFO Level Register This register contains the number of valid data entries in the receive FIFO buffer |
| // 0x0000001f [4:0] : RXFLR (0): Receive FIFO Level |
| io_ro_32 rxflr; |
| |
| _REG_(I2C_IC_SDA_HOLD_OFFSET) // I2C_IC_SDA_HOLD |
| // I2C SDA Hold Time Length Register |
| // 0x00ff0000 [23:16] : IC_SDA_RX_HOLD (0): Sets the required SDA hold time in units of ic_clk period, when DW_apb_i2c... |
| // 0x0000ffff [15:0] : IC_SDA_TX_HOLD (1): Sets the required SDA hold time in units of ic_clk period, when DW_apb_i2c... |
| io_rw_32 sda_hold; |
| |
| _REG_(I2C_IC_TX_ABRT_SOURCE_OFFSET) // I2C_IC_TX_ABRT_SOURCE |
| // I2C Transmit Abort Source Register |
| // 0xff800000 [31:23] : TX_FLUSH_CNT (0): This field indicates the number of Tx FIFO Data Commands which are flushed... |
| // 0x00010000 [16] : ABRT_USER_ABRT (0): This is a master-mode-only bit |
| // 0x00008000 [15] : ABRT_SLVRD_INTX (0): 1: When the processor side responds to a slave mode request for data to be... |
| // 0x00004000 [14] : ABRT_SLV_ARBLOST (0): This field indicates that a Slave has lost the bus while transmitting... |
| // 0x00002000 [13] : ABRT_SLVFLUSH_TXFIFO (0): This field specifies that the Slave has received a read command and... |
| // 0x00001000 [12] : ARB_LOST (0): This field specifies that the Master has lost arbitration, or if... |
| // 0x00000800 [11] : ABRT_MASTER_DIS (0): This field indicates that the User tries to initiate a Master operation... |
| // 0x00000400 [10] : ABRT_10B_RD_NORSTRT (0): This field indicates that the restart is disabled (IC_RESTART_EN bit... |
| // 0x00000200 [9] : ABRT_SBYTE_NORSTRT (0): To clear Bit 9, the source of the ABRT_SBYTE_NORSTRT must be fixed... |
| // 0x00000100 [8] : ABRT_HS_NORSTRT (0): This field indicates that the restart is disabled (IC_RESTART_EN bit... |
| // 0x00000080 [7] : ABRT_SBYTE_ACKDET (0): This field indicates that the Master has sent a START Byte and the START... |
| // 0x00000040 [6] : ABRT_HS_ACKDET (0): This field indicates that the Master is in High Speed mode and the High... |
| // 0x00000020 [5] : ABRT_GCALL_READ (0): This field indicates that DW_apb_i2c in the master mode has sent a General... |
| // 0x00000010 [4] : ABRT_GCALL_NOACK (0): This field indicates that DW_apb_i2c in master mode has sent a General... |
| // 0x00000008 [3] : ABRT_TXDATA_NOACK (0): This field indicates the master-mode only bit |
| // 0x00000004 [2] : ABRT_10ADDR2_NOACK (0): This field indicates that the Master is in 10-bit address mode and that... |
| // 0x00000002 [1] : ABRT_10ADDR1_NOACK (0): This field indicates that the Master is in 10-bit address mode and the... |
| // 0x00000001 [0] : ABRT_7B_ADDR_NOACK (0): This field indicates that the Master is in 7-bit addressing mode and... |
| io_ro_32 tx_abrt_source; |
| |
| _REG_(I2C_IC_SLV_DATA_NACK_ONLY_OFFSET) // I2C_IC_SLV_DATA_NACK_ONLY |
| // Generate Slave Data NACK Register |
| // 0x00000001 [0] : NACK (0): Generate NACK |
| io_rw_32 slv_data_nack_only; |
| |
| _REG_(I2C_IC_DMA_CR_OFFSET) // I2C_IC_DMA_CR |
| // DMA Control Register |
| // 0x00000002 [1] : TDMAE (0): Transmit DMA Enable |
| // 0x00000001 [0] : RDMAE (0): Receive DMA Enable |
| io_rw_32 dma_cr; |
| |
| _REG_(I2C_IC_DMA_TDLR_OFFSET) // I2C_IC_DMA_TDLR |
| // DMA Transmit Data Level Register |
| // 0x0000000f [3:0] : DMATDL (0): Transmit Data Level |
| io_rw_32 dma_tdlr; |
| |
| _REG_(I2C_IC_DMA_RDLR_OFFSET) // I2C_IC_DMA_RDLR |
| // I2C Receive Data Level Register |
| // 0x0000000f [3:0] : DMARDL (0): Receive Data Level |
| io_rw_32 dma_rdlr; |
| |
| _REG_(I2C_IC_SDA_SETUP_OFFSET) // I2C_IC_SDA_SETUP |
| // I2C SDA Setup Register |
| // 0x000000ff [7:0] : SDA_SETUP (0x64): SDA Setup |
| io_rw_32 sda_setup; |
| |
| _REG_(I2C_IC_ACK_GENERAL_CALL_OFFSET) // I2C_IC_ACK_GENERAL_CALL |
| // I2C ACK General Call Register |
| // 0x00000001 [0] : ACK_GEN_CALL (1): ACK General Call |
| io_rw_32 ack_general_call; |
| |
| _REG_(I2C_IC_ENABLE_STATUS_OFFSET) // I2C_IC_ENABLE_STATUS |
| // I2C Enable Status Register |
| // 0x00000004 [2] : SLV_RX_DATA_LOST (0): Slave Received Data Lost |
| // 0x00000002 [1] : SLV_DISABLED_WHILE_BUSY (0): Slave Disabled While Busy (Transmit, Receive) |
| // 0x00000001 [0] : IC_EN (0): ic_en Status |
| io_ro_32 enable_status; |
| |
| _REG_(I2C_IC_FS_SPKLEN_OFFSET) // I2C_IC_FS_SPKLEN |
| // I2C SS, FS or FM+ spike suppression limit |
| // 0x000000ff [7:0] : IC_FS_SPKLEN (0x7): This register must be set before any I2C bus transaction can take place to... |
| io_rw_32 fs_spklen; |
| |
| uint32_t _pad2; |
| |
| _REG_(I2C_IC_CLR_RESTART_DET_OFFSET) // I2C_IC_CLR_RESTART_DET |
| // Clear RESTART_DET Interrupt Register |
| // 0x00000001 [0] : CLR_RESTART_DET (0): Read this register to clear the RESTART_DET interrupt (bit 12) of... |
| io_ro_32 clr_restart_det; |
| |
| uint32_t _pad3[18]; |
| |
| _REG_(I2C_IC_COMP_PARAM_1_OFFSET) // I2C_IC_COMP_PARAM_1 |
| // Component Parameter Register 1 |
| // 0x00ff0000 [23:16] : TX_BUFFER_DEPTH (0): TX Buffer Depth = 16 |
| // 0x0000ff00 [15:8] : RX_BUFFER_DEPTH (0): RX Buffer Depth = 16 |
| // 0x00000080 [7] : ADD_ENCODED_PARAMS (0): Encoded parameters not visible |
| // 0x00000040 [6] : HAS_DMA (0): DMA handshaking signals are enabled |
| // 0x00000020 [5] : INTR_IO (0): COMBINED Interrupt outputs |
| // 0x00000010 [4] : HC_COUNT_VALUES (0): Programmable count values for each mode |
| // 0x0000000c [3:2] : MAX_SPEED_MODE (0): MAX SPEED MODE = FAST MODE |
| // 0x00000003 [1:0] : APB_DATA_WIDTH (0): APB data bus width is 32 bits |
| io_ro_32 comp_param_1; |
| |
| _REG_(I2C_IC_COMP_VERSION_OFFSET) // I2C_IC_COMP_VERSION |
| // I2C Component Version Register |
| // 0xffffffff [31:0] : IC_COMP_VERSION (0x3230312a) |
| io_ro_32 comp_version; |
| |
| _REG_(I2C_IC_COMP_TYPE_OFFSET) // I2C_IC_COMP_TYPE |
| // I2C Component Type Register |
| // 0xffffffff [31:0] : IC_COMP_TYPE (0x44570140): Designware Component Type number = 0x44_57_01_40 |
| io_ro_32 comp_type; |
| } i2c_hw_t; |
| |
| #define i2c0_hw ((i2c_hw_t *)I2C0_BASE) |
| #define i2c1_hw ((i2c_hw_t *)I2C1_BASE) |
| |
| #endif |