driver: uart: esp32: DT fix to allow uart2
UART2 would not be available with current DT implementation.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
diff --git a/drivers/serial/uart_esp32.c b/drivers/serial/uart_esp32.c
index 1d33d50..2d08118 100644
--- a/drivers/serial/uart_esp32.c
+++ b/drivers/serial/uart_esp32.c
@@ -80,7 +80,7 @@
int cts;
} pins;
- const clock_control_subsys_t peripheral_id;
+ const clock_control_subsys_t clock_subsys;
const struct {
int source;
@@ -192,7 +192,7 @@
uint32_t sys_clk_freq = 0;
if (clock_control_get_rate(DEV_CFG(dev)->clock_dev,
- DEV_CFG(dev)->peripheral_id,
+ DEV_CFG(dev)->clock_subsys,
&sys_clk_freq)) {
return -EINVAL;
}
@@ -248,7 +248,7 @@
| (UART_TX_FIFO_THRESH << UART_TXFIFO_EMPTY_THRHD_S);
uart_esp32_configure_pins(dev);
- clock_control_on(DEV_CFG(dev)->clock_dev, DEV_CFG(dev)->peripheral_id);
+ clock_control_on(DEV_CFG(dev)->clock_dev, DEV_CFG(dev)->clock_subsys);
/*
* Reset RX Buffer by reading all received bytes
@@ -492,11 +492,11 @@
static const DRAM_ATTR struct uart_esp32_config uart_esp32_cfg_port_##idx = { \
.dev_conf = { \
.base = \
- (uint8_t *)DT_INST_REG_ADDR(idx), \
+ (uint8_t *)DT_REG_ADDR(DT_NODELABEL(uart##idx)), \
ESP32_UART_IRQ_HANDLER_FUNC(idx) \
}, \
\
- .clock_dev = DEVICE_DT_GET(DT_INST_CLOCKS_CTLR(idx)), \
+ .clock_dev = DEVICE_DT_GET(DT_CLOCKS_CTLR(DT_NODELABEL(uart##idx))), \
\
.signals = { \
.tx_out = U##idx##TXD_OUT_IDX, \
@@ -506,16 +506,16 @@
}, \
\
.pins = { \
- .tx = DT_INST_PROP(idx, tx_pin), \
- .rx = DT_INST_PROP(idx, rx_pin), \
+ .tx = DT_PROP(DT_NODELABEL(uart##idx), tx_pin), \
+ .rx = DT_PROP(DT_NODELABEL(uart##idx), rx_pin), \
IF_ENABLED( \
- DT_INST_PROP(idx, hw_flow_control), \
- (.rts = DT_INST_PROP(idx, rts_pin), \
- .cts = DT_INST_PROP(idx, cts_pin), \
+ DT_PROP(DT_NODELABEL(uart##idx), hw_flow_control), \
+ (.rts = DT_PROP(DT_NODELABEL(uart##idx), rts_pin), \
+ .cts = DT_PROP(DT_NODELABEL(uart##idx), cts_pin), \
)) \
}, \
\
- .peripheral_id = (clock_control_subsys_t)DT_INST_CLOCKS_CELL(idx, offset), \
+ .clock_subsys = (clock_control_subsys_t)DT_CLOCKS_CELL(DT_NODELABEL(uart##idx), offset), \
.irq = { \
.source = ETS_UART##idx##_INTR_SOURCE, \
.line = INST_##idx##_ESPRESSIF_ESP32_UART_IRQ_0, \
@@ -524,19 +524,19 @@
\
static struct uart_esp32_data uart_esp32_data_##idx = { \
.uart_config = { \
- .baudrate = DT_INST_PROP(idx, current_speed),\
+ .baudrate = DT_PROP(DT_NODELABEL(uart##idx), current_speed),\
.parity = UART_CFG_PARITY_NONE, \
.stop_bits = UART_CFG_STOP_BITS_1, \
.data_bits = UART_CFG_DATA_BITS_8, \
.flow_ctrl = IS_ENABLED( \
- DT_INST_PROP(idx, hw_flow_control)) ?\
+ DT_PROP(DT_NODELABEL(uart##idx), hw_flow_control)) ?\
UART_CFG_FLOW_CTRL_RTS_CTS : UART_CFG_FLOW_CTRL_NONE \
} \
}; \
\
-DEVICE_DT_INST_DEFINE(idx, \
- uart_esp32_init, \
- NULL, \
+DEVICE_DT_DEFINE(DT_NODELABEL(uart##idx), \
+ &uart_esp32_init, \
+ NULL, \
&uart_esp32_data_##idx, \
&uart_esp32_cfg_port_##idx, \
PRE_KERNEL_1, \
@@ -545,4 +545,14 @@
\
ESP32_UART_IRQ_HANDLER(idx)
-DT_INST_FOREACH_STATUS_OKAY(ESP32_UART_INIT)
+#if DT_NODE_HAS_STATUS(DT_NODELABEL(uart0), okay)
+ESP32_UART_INIT(0);
+#endif
+
+#if DT_NODE_HAS_STATUS(DT_NODELABEL(uart1), okay)
+ESP32_UART_INIT(1);
+#endif
+
+#if DT_NODE_HAS_STATUS(DT_NODELABEL(uart2), okay)
+ESP32_UART_INIT(2);
+#endif
