//***************************************************************************** | |
// | |
// hw_ints.h - Macros that define the interrupt assignment on Stellaris. | |
// | |
// Copyright (c) 2005-2008 Luminary Micro, Inc. All rights reserved. | |
// | |
// Software License Agreement | |
// | |
// Luminary Micro, Inc. (LMI) is supplying this software for use solely and | |
// exclusively on LMI's microcontroller products. | |
// | |
// The software is owned by LMI and/or its suppliers, and is protected under | |
// applicable copyright laws. All rights are reserved. You may not combine | |
// this software with "viral" open-source software in order to form a larger | |
// program. Any use in violation of the foregoing restrictions may subject | |
// the user to criminal sanctions under applicable laws, as well as to civil | |
// liability for the breach of the terms and conditions of this license. | |
// | |
// THIS SOFTWARE IS PROVIDED "AS IS". NO WARRANTIES, WHETHER EXPRESS, IMPLIED | |
// OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF | |
// MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE APPLY TO THIS SOFTWARE. | |
// LMI SHALL NOT, IN ANY CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL, OR | |
// CONSEQUENTIAL DAMAGES, FOR ANY REASON WHATSOEVER. | |
// | |
// This is part of revision 2523 of the Stellaris Peripheral Driver Library. | |
// | |
//***************************************************************************** | |
#ifndef __HW_INTS_H__ | |
#define __HW_INTS_H__ | |
//***************************************************************************** | |
// | |
// The following are defines for the fault assignments. | |
// | |
//***************************************************************************** | |
#define FAULT_NMI 2 // NMI fault | |
#define FAULT_HARD 3 // Hard fault | |
#define FAULT_MPU 4 // MPU fault | |
#define FAULT_BUS 5 // Bus fault | |
#define FAULT_USAGE 6 // Usage fault | |
#define FAULT_SVCALL 11 // SVCall | |
#define FAULT_DEBUG 12 // Debug monitor | |
#define FAULT_PENDSV 14 // PendSV | |
#define FAULT_SYSTICK 15 // System Tick | |
//***************************************************************************** | |
// | |
// The following are defines for the interrupt assignments. | |
// | |
//***************************************************************************** | |
#define INT_GPIOA 16 // GPIO Port A | |
#define INT_GPIOB 17 // GPIO Port B | |
#define INT_GPIOC 18 // GPIO Port C | |
#define INT_GPIOD 19 // GPIO Port D | |
#define INT_GPIOE 20 // GPIO Port E | |
#define INT_UART0 21 // UART0 Rx and Tx | |
#define INT_UART1 22 // UART1 Rx and Tx | |
#define INT_SSI0 23 // SSI0 Rx and Tx | |
#define INT_I2C0 24 // I2C0 Master and Slave | |
#define INT_PWM_FAULT 25 // PWM Fault | |
#define INT_PWM0 26 // PWM Generator 0 | |
#define INT_PWM1 27 // PWM Generator 1 | |
#define INT_PWM2 28 // PWM Generator 2 | |
#define INT_QEI0 29 // Quadrature Encoder 0 | |
#define INT_ADC0 30 // ADC Sequence 0 | |
#define INT_ADC1 31 // ADC Sequence 1 | |
#define INT_ADC2 32 // ADC Sequence 2 | |
#define INT_ADC3 33 // ADC Sequence 3 | |
#define INT_WATCHDOG 34 // Watchdog timer | |
#define INT_TIMER0A 35 // Timer 0 subtimer A | |
#define INT_TIMER0B 36 // Timer 0 subtimer B | |
#define INT_TIMER1A 37 // Timer 1 subtimer A | |
#define INT_TIMER1B 38 // Timer 1 subtimer B | |
#define INT_TIMER2A 39 // Timer 2 subtimer A | |
#define INT_TIMER2B 40 // Timer 2 subtimer B | |
#define INT_COMP0 41 // Analog Comparator 0 | |
#define INT_COMP1 42 // Analog Comparator 1 | |
#define INT_COMP2 43 // Analog Comparator 2 | |
#define INT_SYSCTL 44 // System Control (PLL, OSC, BO) | |
#define INT_FLASH 45 // FLASH Control | |
#define INT_GPIOF 46 // GPIO Port F | |
#define INT_GPIOG 47 // GPIO Port G | |
#define INT_GPIOH 48 // GPIO Port H | |
#define INT_UART2 49 // UART2 Rx and Tx | |
#define INT_SSI1 50 // SSI1 Rx and Tx | |
#define INT_TIMER3A 51 // Timer 3 subtimer A | |
#define INT_TIMER3B 52 // Timer 3 subtimer B | |
#define INT_I2C1 53 // I2C1 Master and Slave | |
#define INT_QEI1 54 // Quadrature Encoder 1 | |
#define INT_CAN0 55 // CAN0 | |
#define INT_CAN1 56 // CAN1 | |
#define INT_CAN2 57 // CAN2 | |
#define INT_ETH 58 // Ethernet | |
#define INT_HIBERNATE 59 // Hibernation module | |
#define INT_USB0 60 // USB 0 Controller | |
#define INT_PWM3 61 // PWM Generator 3 | |
#define INT_UDMA 62 // uDMA controller | |
#define INT_UDMAERR 63 // uDMA Error | |
//***************************************************************************** | |
// | |
// The following are defines for the total number of interrupts. | |
// | |
//***************************************************************************** | |
#define NUM_INTERRUPTS 64 | |
//***************************************************************************** | |
// | |
// The following are defines for the total number of priority levels. | |
// | |
//***************************************************************************** | |
#define NUM_PRIORITY 8 | |
#define NUM_PRIORITY_BITS 3 | |
//***************************************************************************** | |
// | |
// The following definitions are deprecated. | |
// | |
//***************************************************************************** | |
#ifndef DEPRECATED | |
//***************************************************************************** | |
// | |
// The following are deprecated defines for the interrupt assignments. | |
// | |
//***************************************************************************** | |
#define INT_SSI 23 // SSI Rx and Tx | |
#define INT_I2C 24 // I2C Master and Slave | |
#define INT_QEI 29 // Quadrature Encoder | |
#endif | |
#endif // __HW_INTS_H__ |