FreeRTOS-Plus/Source/FreeRTOS-Plus-TCP/portable/NetworkInterface/STM32F7xx/stm32f7xx_hal_eth.c

/**
  ******************************************************************************
  * @file    stm32f7xx_hal_eth.c
  * @author  MCD Application Team
  * @version V1.3.2
  * @date    26-June-2015
  * @brief   ETH HAL module driver.
  *          This file provides firmware functions to manage the following 
  *          functionalities of the Ethernet (ETH) peripheral:
  *           + Initialization and de-initialization functions
  *           + IO operation functions
  *           + Peripheral Control functions 
  *           + Peripheral State and Errors functions
  *
  @verbatim
  ==============================================================================
                    ##### How to use this driver #####
  ==============================================================================
    [..]
      (#)Declare a ETH_HandleTypeDef handle structure, for example:
         ETH_HandleTypeDef  heth;
        
      (#)Fill parameters of Init structure in heth handle
  
      (#)Call HAL_ETH_Init() API to initialize the Ethernet peripheral (MAC, DMA, ...) 

      (#)Initialize the ETH low level resources through the HAL_ETH_MspInit() API:
          (##) Enable the Ethernet interface clock using 
               (+++) __HAL_RCC_ETHMAC_CLK_ENABLE();
               (+++) __HAL_RCC_ETHMACTX_CLK_ENABLE();
               (+++) __HAL_RCC_ETHMACRX_CLK_ENABLE();
           
          (##) Initialize the related GPIO clocks
          (##) Configure Ethernet pin-out
          (##) Configure Ethernet NVIC interrupt (IT mode)   
    
      (#)Initialize Ethernet DMA Descriptors in chain mode and point to allocated buffers:
          (##) HAL_ETH_DMATxDescListInit(); for Transmission process
          (##) HAL_ETH_DMARxDescListInit(); for Reception process

      (#)Enable MAC and DMA transmission and reception:
          (##) HAL_ETH_Start();

      (#)Prepare ETH DMA TX Descriptors and give the hand to ETH DMA to transfer 
         the frame to MAC TX FIFO:
         (##) HAL_ETH_TransmitFrame();

      (#)Poll for a received frame in ETH RX DMA Descriptors and get received 
         frame parameters
         (##) HAL_ETH_GetReceivedFrame(); (should be called into an infinite loop)

      (#) Get a received frame when an ETH RX interrupt occurs:
         (##) HAL_ETH_GetReceivedFrame_IT(); (called in IT mode only)

      (#) Communicate with external PHY device:
         (##) Read a specific register from the PHY  
              HAL_ETH_ReadPHYRegister();
         (##) Write data to a specific RHY register:
              HAL_ETH_WritePHYRegister();

      (#) Configure the Ethernet MAC after ETH peripheral initialization
          HAL_ETH_ConfigMAC(); all MAC parameters should be filled.
      
      (#) Configure the Ethernet DMA after ETH peripheral initialization
          HAL_ETH_ConfigDMA(); all DMA parameters should be filled.

      -@- The PTP protocol and the DMA descriptors ring mode are not supported
          in this driver

  @endverbatim
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; COPYRIGHT(c) 2015 STMicroelectronics</center></h2>
  *
  * Redistribution and use in source and binary forms, with or without modification,
  * are permitted provided that the following conditions are met:
  *   1. Redistributions of source code must retain the above copyright notice,
  *      this list of conditions and the following disclaimer.
  *   2. Redistributions in binary form must reproduce the above copyright notice,
  *      this list of conditions and the following disclaimer in the documentation
  *      and/or other materials provided with the distribution.
  *   3. Neither the name of STMicroelectronics nor the names of its contributors
  *      may be used to endorse or promote products derived from this software
  *      without specific prior written permission.
  *
  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  *
  ******************************************************************************
  */ 

/* Includes ------------------------------------------------------------------*/
#include "stm32f7xx_hal.h"


int lUDPLoggingPrintf( const char *pcFormatString, ... );

/** @addtogroup STM32F4xx_HAL_Driver
  * @{
  */

/** @defgroup ETH ETH
  * @brief ETH HAL module driver
  * @{
  */

#if !defined( ARRAY_SIZE )
	#define ARRAY_SIZE( x ) ( sizeof ( x ) / sizeof ( x )[ 0 ] )
#endif

#ifdef HAL_ETH_MODULE_ENABLED

#if defined(STM32F7xx)

/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/** @defgroup ETH_Private_Constants ETH Private Constants
  * @{
  */
#define LINKED_STATE_TIMEOUT_VALUE          ((uint32_t)2000)  /* 2000 ms */
#define AUTONEGO_COMPLETED_TIMEOUT_VALUE    ((uint32_t)1000)  /* 1000 ms */

/**
  * @}
  */
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
/** @defgroup ETH_Private_Functions ETH Private Functions
  * @{
  */
static void ETH_MACDMAConfig(ETH_HandleTypeDef *heth, uint32_t err);
static void ETH_MACAddressConfig(ETH_HandleTypeDef *heth, uint32_t MacAddr, uint8_t *Addr);
static void ETH_MACReceptionEnable(ETH_HandleTypeDef *heth);
static void ETH_MACReceptionDisable(ETH_HandleTypeDef *heth);
static void ETH_MACTransmissionEnable(ETH_HandleTypeDef *heth);
static void ETH_MACTransmissionDisable(ETH_HandleTypeDef *heth);
static void ETH_DMATransmissionEnable(ETH_HandleTypeDef *heth);
static void ETH_DMATransmissionDisable(ETH_HandleTypeDef *heth);
static void ETH_DMAReceptionEnable(ETH_HandleTypeDef *heth);
static void ETH_DMAReceptionDisable(ETH_HandleTypeDef *heth);
static void ETH_FlushTransmitFIFO(ETH_HandleTypeDef *heth);

/**
  * @}
  */
/* Private functions ---------------------------------------------------------*/

/** @defgroup ETH_Exported_Functions ETH Exported Functions
  * @{
  */

/** @defgroup ETH_Exported_Functions_Group1 Initialization and de-initialization functions
  *  @brief   Initialization and Configuration functions
  *
  @verbatim
  ===============================================================================
            ##### Initialization and de-initialization functions #####
  ===============================================================================
  [..]  This section provides functions allowing to:
      (+) Initialize and configure the Ethernet peripheral
      (+) De-initialize the Ethernet peripheral

  @endverbatim
  * @{
  */
extern void vMACBProbePhy ( void );

/**
  * @brief  Initializes the Ethernet MAC and DMA according to default
  *         parameters.
  * @param  heth: pointer to a ETH_HandleTypeDef structure that contains
  *         the configuration information for ETHERNET module
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_ETH_Init(ETH_HandleTypeDef *heth)
{
	uint32_t tmpreg = 0;
	uint32_t hclk = 60000000;
	uint32_t err = ETH_SUCCESS;

	/* Check the ETH peripheral state */
	if( heth == NULL )
	{
		return HAL_ERROR;
	}

	/* Check parameters */
	assert_param(IS_ETH_AUTONEGOTIATION(heth->Init.AutoNegotiation));
	assert_param(IS_ETH_RX_MODE(heth->Init.RxMode));
	assert_param(IS_ETH_CHECKSUM_MODE(heth->Init.ChecksumMode));
	assert_param(IS_ETH_MEDIA_INTERFACE(heth->Init.MediaInterface));

	if( heth->State == HAL_ETH_STATE_RESET )
	{
		/* Init the low level hardware : GPIO, CLOCK, NVIC. */
		HAL_ETH_MspInit( heth );
	}

	/* Enable SYSCFG Clock */
	__HAL_RCC_SYSCFG_CLK_ENABLE();

	/* Select MII or RMII Mode*/
	SYSCFG->PMC &= ~(SYSCFG_PMC_MII_RMII_SEL);
	SYSCFG->PMC |= (uint32_t)heth->Init.MediaInterface;

	/* Ethernet Software reset */
	/* Set the SWR bit: resets all MAC subsystem internal registers and logic */
	/* After reset all the registers holds their respective reset values */
	/* Also enable EDFE: Enhanced descriptor format enable. */
//	heth->Instance->DMABMR |= ETH_DMABMR_SR | ETH_DMABMR_EDE;
	heth->Instance->DMABMR |= ETH_DMABMR_SR;

	/* Wait for software reset */
	while ((heth->Instance->DMABMR & ETH_DMABMR_SR) != (uint32_t)RESET)
	{
	}

	/*-------------------------------- MAC Initialization ----------------------*/
	/* Get the ETHERNET MACMIIAR value */
	tmpreg = heth->Instance->MACMIIAR;
	/* Clear CSR Clock Range CR[2:0] bits */
	tmpreg &= ETH_MACMIIAR_CR_MASK;

	/* Get hclk frequency value (168,000,000) */
	hclk = HAL_RCC_GetHCLKFreq();

	/* Set CR bits depending on hclk value */
	if( ( hclk >= 20000000 ) && ( hclk < 35000000 ) )
	{
		/* CSR Clock Range between 20-35 MHz */
		tmpreg |= (uint32_t) ETH_MACMIIAR_CR_Div16;
	}
	else if( ( hclk >= 35000000 ) && ( hclk < 60000000 ) )
	{
	/* CSR Clock Range between 35-60 MHz */
	tmpreg |= ( uint32_t ) ETH_MACMIIAR_CR_Div26;
	}
	else if((hclk >= 60000000 ) && ( hclk < 100000000 ) )
	{
		/* CSR Clock Range between 60-100 MHz */
		tmpreg |= (uint32_t)ETH_MACMIIAR_CR_Div42;
	}
	else if((hclk >= 100000000 ) && ( hclk < 150000000))
	{
		/* CSR Clock Range between 100-150 MHz */
		tmpreg |= (uint32_t)ETH_MACMIIAR_CR_Div62;
	}
	else /* ((hclk >= 150000000 ) && ( hclk <= 168000000)) */
	{
		/* CSR Clock Range between 150-168 MHz */
		tmpreg |= (uint32_t)ETH_MACMIIAR_CR_Div102;
	}

	/* Write to ETHERNET MAC MIIAR: Configure the ETHERNET CSR Clock Range */
	heth->Instance->MACMIIAR = (uint32_t)tmpreg;

	/* Initialise the MACB and set all PHY properties */
	vMACBProbePhy();

	/* Config MAC and DMA */
	ETH_MACDMAConfig(heth, err);

	/* Set ETH HAL State to Ready */
	heth->State= HAL_ETH_STATE_READY;

	/* Return function status */
	return HAL_OK;
}

/**
  * @brief  De-Initializes the ETH peripheral.
  * @param  heth: pointer to a ETH_HandleTypeDef structure that contains
  *         the configuration information for ETHERNET module
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_ETH_DeInit(ETH_HandleTypeDef *heth)
{
	/* Set the ETH peripheral state to BUSY */
	heth->State = HAL_ETH_STATE_BUSY;

	/* De-Init the low level hardware : GPIO, CLOCK, NVIC. */
	HAL_ETH_MspDeInit( heth );

	/* Set ETH HAL state to Disabled */
	heth->State= HAL_ETH_STATE_RESET;

	/* Release Lock */
	__HAL_UNLOCK( heth );

	/* Return function status */
	return HAL_OK;
}

/**
  * @brief  Initializes the DMA Tx descriptors in chain mode.
  * @param  heth: pointer to a ETH_HandleTypeDef structure that contains
  *         the configuration information for ETHERNET module
  * @param  DMATxDescTab: Pointer to the first Tx desc list
  * @param  TxBuff: Pointer to the first TxBuffer list
  * @param  TxBuffCount: Number of the used Tx desc in the list
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_ETH_DMATxDescListInit(ETH_HandleTypeDef *heth, ETH_DMADescTypeDef *pxDMATable, uint8_t *ucDataBuffer, uint32_t ulBufferCount)
{
	uint32_t i = 0;
	ETH_DMADescTypeDef *pxDMADescriptor;

	/* Process Locked */
	__HAL_LOCK( heth );

	/* Set the ETH peripheral state to BUSY */
	heth->State = HAL_ETH_STATE_BUSY;

	/* Set the TxDesc pointer with the first one of the pxDMATable list */
	heth->TxDesc = pxDMATable;

	/* Fill each DMA descriptor with the right values */
	for( i=0; i < ulBufferCount; i++ )
	{
		/* Get the pointer on the ith member of the descriptor list */
		pxDMADescriptor = pxDMATable + i;

		/* Set Second Address Chained bit */
		pxDMADescriptor->Status = ETH_DMATXDESC_TCH;

		pxDMADescriptor->ControlBufferSize = 0;

		/* Set Buffer1 address pointer */
		if( ucDataBuffer != NULL )
		{
			pxDMADescriptor->Buffer1Addr = ( uint32_t )( &ucDataBuffer[ i * ETH_TX_BUF_SIZE ] );
		}
		else
		{
			/* Buffer space is not provided because it uses zero-copy transmissions. */
			pxDMADescriptor->Buffer1Addr = ( uint32_t )0u;
		}

		if (heth->Init.ChecksumMode == ETH_CHECKSUM_BY_HARDWARE)
		{
			/* Set the DMA Tx descriptors checksum insertion for TCP, UDP, and ICMP */
			pxDMADescriptor->Status |= ETH_DMATXDESC_CHECKSUMTCPUDPICMPFULL;
		}

		/* Initialize the next descriptor with the Next Descriptor Polling Enable */
		if(i < ( ulBufferCount - 1 ) )
		{
			/* Set next descriptor address register with next descriptor base address */
			pxDMADescriptor->Buffer2NextDescAddr = ( uint32_t ) ( pxDMATable + i + 1 );
		}
		else
		{
			/* For last descriptor, set next descriptor address register equal to the first descriptor base address */
			pxDMADescriptor->Buffer2NextDescAddr = ( uint32_t ) pxDMATable;
		}
	}

	/* Set Transmit Descriptor List Address Register */
	heth->Instance->DMATDLAR = ( uint32_t ) pxDMATable;

	/* Set ETH HAL State to Ready */
	heth->State= HAL_ETH_STATE_READY;

	/* Process Unlocked */
	__HAL_UNLOCK( heth );

	/* Return function status */
	return HAL_OK;
}

/**
  * @brief  Initializes the DMA Rx descriptors in chain mode.
  * @param  heth: pointer to a ETH_HandleTypeDef structure that contains
  *         the configuration information for ETHERNET module
  * @param  DMARxDescTab: Pointer to the first Rx desc list
  * @param  RxBuff: Pointer to the first RxBuffer list
  * @param  RxBuffCount: Number of the used Rx desc in the list
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_ETH_DMARxDescListInit(ETH_HandleTypeDef *heth, ETH_DMADescTypeDef *pxDMATable, uint8_t *ucDataBuffer, uint32_t ulBufferCount)
{
	uint32_t i = 0;
	ETH_DMADescTypeDef *pxDMADescriptor;

	/* Process Locked */
	__HAL_LOCK( heth );

	/* Set the ETH peripheral state to BUSY */
	heth->State = HAL_ETH_STATE_BUSY;

	/* Set the RxDesc pointer with the first one of the pxDMATable list */
	heth->RxDesc = pxDMATable;

	/* Fill each DMA descriptor with the right values */
	for(i=0; i < ulBufferCount; i++)
	{
		/* Get the pointer on the ith member of the descriptor list */
		pxDMADescriptor = pxDMATable+i;

		/* Set Own bit of the Rx descriptor Status */
		pxDMADescriptor->Status = ETH_DMARXDESC_OWN;

		/* Set Buffer1 size and Second Address Chained bit */
		pxDMADescriptor->ControlBufferSize = ETH_DMARXDESC_RCH | ETH_RX_BUF_SIZE;

		/* Set Buffer1 address pointer */
		if( ucDataBuffer != NULL )
		{
			pxDMADescriptor->Buffer1Addr = ( uint32_t )( &ucDataBuffer[ i * ETH_RX_BUF_SIZE ] );
		}
		else
		{
			/* Buffer space is not provided because it uses zero-copy reception. */
			pxDMADescriptor->Buffer1Addr = ( uint32_t )0u;
		}

		if( heth->Init.RxMode == ETH_RXINTERRUPT_MODE )
		{
			/* Enable Ethernet DMA Rx Descriptor interrupt */
			pxDMADescriptor->ControlBufferSize &= ~ETH_DMARXDESC_DIC;
		}

		/* Initialize the next descriptor with the Next Descriptor Polling Enable */
		if(i < (ulBufferCount-1))
		{
			/* Set next descriptor address register with next descriptor base address */
			pxDMADescriptor->Buffer2NextDescAddr = (uint32_t)(pxDMATable+i+1);
		}
		else
		{
			/* For last descriptor, set next descriptor address register equal to the first descriptor base address */
			pxDMADescriptor->Buffer2NextDescAddr = ( uint32_t ) pxDMATable;
		}
	}

	/* Set Receive Descriptor List Address Register */
	heth->Instance->DMARDLAR = ( uint32_t ) pxDMATable;

	/* Set ETH HAL State to Ready */
	heth->State= HAL_ETH_STATE_READY;

	/* Process Unlocked */
	__HAL_UNLOCK( heth );

	/* Return function status */
	return HAL_OK;
}

/**
  * @brief  Initializes the ETH MSP.
  * @param  heth: pointer to a ETH_HandleTypeDef structure that contains
  *         the configuration information for ETHERNET module
  * @retval None
  */
__weak void HAL_ETH_MspInit(ETH_HandleTypeDef *heth)
{
  /* NOTE : This function Should not be modified, when the callback is needed,
  the HAL_ETH_MspInit could be implemented in the user file
  */
}

/**
  * @brief  DeInitializes ETH MSP.
  * @param  heth: pointer to a ETH_HandleTypeDef structure that contains
  *         the configuration information for ETHERNET module
  * @retval None
  */
__weak void HAL_ETH_MspDeInit(ETH_HandleTypeDef *heth)
{
  /* NOTE : This function Should not be modified, when the callback is needed,
  the HAL_ETH_MspDeInit could be implemented in the user file
  */
}

/**
  * @}
  */

/** @defgroup ETH_Exported_Functions_Group2 IO operation functions
  *  @brief   Data transfers functions
  *
  @verbatim
  ==============================================================================
                          ##### IO operation functions #####
  ==============================================================================
  [..]  This section provides functions allowing to:
        (+) Transmit a frame
            HAL_ETH_TransmitFrame();
        (+) Receive a frame
            HAL_ETH_GetReceivedFrame();
            HAL_ETH_GetReceivedFrame_IT();
        (+) Read from an External PHY register
            HAL_ETH_ReadPHYRegister();
        (+) Write to an External PHY register
            HAL_ETH_WritePHYRegister();

  @endverbatim

  * @{
  */

/**
  * @brief  Sends an Ethernet frame.
  * @param  heth: pointer to a ETH_HandleTypeDef structure that contains
  *         the configuration information for ETHERNET module
  * @param  FrameLength: Amount of data to be sent
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_ETH_TransmitFrame(ETH_HandleTypeDef *heth, uint32_t FrameLength)
{
	uint32_t bufcount = 0, size = 0, i = 0;
	__IO ETH_DMADescTypeDef *pxDmaTxDesc = heth->TxDesc;
	/* Process Locked */
	__HAL_LOCK( heth );

	/* Set the ETH peripheral state to BUSY */
	heth->State = HAL_ETH_STATE_BUSY;

	if( FrameLength == 0 )
	{
		/* Set ETH HAL state to READY */
		heth->State = HAL_ETH_STATE_READY;

		/* Process Unlocked */
		__HAL_UNLOCK( heth );

		return  HAL_ERROR;
	}

	/* Check if the descriptor is owned by the ETHERNET DMA (when set) or CPU (when reset) */
	if( ( pxDmaTxDesc->Status & ETH_DMATXDESC_OWN ) != ( uint32_t ) RESET )
	{
		/* OWN bit set */
		heth->State = HAL_ETH_STATE_BUSY_TX;

		/* Process Unlocked */
		__HAL_UNLOCK( heth );

		return HAL_ERROR;
	}

	/* Get the number of needed Tx buffers for the current frame, rounding up. */
	bufcount = ( FrameLength + ETH_TX_BUF_SIZE - 1 ) / ETH_TX_BUF_SIZE;

	if (bufcount == 1)
	{
		/* Set LAST and FIRST segment */
		pxDmaTxDesc->Status |= ETH_DMATXDESC_FS | ETH_DMATXDESC_LS;
		/* Set frame size */
		pxDmaTxDesc->ControlBufferSize = ( FrameLength & ETH_DMATXDESC_TBS1 );
		/* Set Own bit of the Tx descriptor Status: gives the buffer back to ETHERNET DMA */
		pxDmaTxDesc->Status |= ETH_DMATXDESC_OWN;
		/* Point to next descriptor */
		heth->TxDesc = ( ETH_DMADescTypeDef * ) ( heth->TxDesc->Buffer2NextDescAddr );
	}
	else
	{
		for( i = 0; i < bufcount; i++ )
		{
			/* Clear FIRST and LAST segment bits */
		uint32_t ulStatus = heth->TxDesc->Status & ~( ETH_DMATXDESC_FS | ETH_DMATXDESC_LS );

			if( i == 0 )
			{
				/* Setting the first segment bit */
				heth->TxDesc->Status = ulStatus | ETH_DMATXDESC_FS;
			}

			/* Program size */
			if (i < (bufcount-1))
			{
				heth->TxDesc->ControlBufferSize = (ETH_TX_BUF_SIZE & ETH_DMATXDESC_TBS1);
			}
			else
			{
				/* Setting the last segment bit */
				heth->TxDesc->Status = ulStatus | ETH_DMATXDESC_LS;
				size = FrameLength - (bufcount-1)*ETH_TX_BUF_SIZE;
				heth->TxDesc->ControlBufferSize = (size & ETH_DMATXDESC_TBS1);
			}

			/* Set Own bit of the Tx descriptor Status: gives the buffer back to ETHERNET DMA */
			heth->TxDesc->Status |= ETH_DMATXDESC_OWN;
			/* point to next descriptor */
			heth->TxDesc = (ETH_DMADescTypeDef *)( heth->TxDesc->Buffer2NextDescAddr );
		}
	}

	__DSB();

	/* When Tx Buffer unavailable flag is set: clear it and resume transmission */
	if( ( heth->Instance->DMASR & ETH_DMASR_TBUS ) != ( uint32_t )RESET )
	{
		heth->Instance->DMACHTDR = ( uint32_t )pxDmaTxDesc;

		/* Clear TBUS ETHERNET DMA flag */
		heth->Instance->DMASR = ETH_DMASR_TBUS;
		/* Resume DMA transmission*/
		heth->Instance->DMATPDR = 0;
	}

	/* Set ETH HAL State to Ready */
	heth->State = HAL_ETH_STATE_READY;

	/* Process Unlocked */
	__HAL_UNLOCK( heth );

	/* Return function status */
	return HAL_OK;
}

/**
  * @brief  Checks for received frames.
  * @param  heth: pointer to a ETH_HandleTypeDef structure that contains
  *         the configuration information for ETHERNET module
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_ETH_GetReceivedFrame_IT( ETH_HandleTypeDef *heth )
{
	return HAL_ETH_GetReceivedFrame( heth );
}

HAL_StatusTypeDef HAL_ETH_GetReceivedFrame( ETH_HandleTypeDef *heth )
{
uint32_t ulCounter = 0;
ETH_DMADescTypeDef *pxDescriptor = heth->RxDesc;
HAL_StatusTypeDef xResult = HAL_ERROR;

	/* Process Locked */
	__HAL_LOCK( heth );

	/* Check the ETH state to BUSY */
	heth->State = HAL_ETH_STATE_BUSY;

	/* Scan descriptors owned by CPU */
	while( ( ( pxDescriptor->Status & ETH_DMARXDESC_OWN ) == 0ul ) && ( ulCounter < ETH_RXBUFNB ) )
	{
	uint32_t ulStatus = pxDescriptor->Status;

		/* Just for security. */
		ulCounter++;

		if( ( ulStatus & ( ETH_DMARXDESC_FS | ETH_DMARXDESC_LS ) ) == ( uint32_t )ETH_DMARXDESC_FS )
		{
			/* First segment in frame, but not the last. */
			heth->RxFrameInfos.FSRxDesc = pxDescriptor;
			heth->RxFrameInfos.LSRxDesc = ( ETH_DMADescTypeDef *)NULL;
			heth->RxFrameInfos.SegCount = 1;
			/* Point to next descriptor. */
			pxDescriptor = (ETH_DMADescTypeDef*) (pxDescriptor->Buffer2NextDescAddr);
			heth->RxDesc = pxDescriptor;
		}
		else if( ( ulStatus & ( ETH_DMARXDESC_LS | ETH_DMARXDESC_FS ) ) == 0ul )
		{
			/* This is an intermediate segment, not first, not last. */
			/* Increment segment count. */
			heth->RxFrameInfos.SegCount++;
			/* Move to the next descriptor. */
			pxDescriptor = ( ETH_DMADescTypeDef * ) ( pxDescriptor->Buffer2NextDescAddr );
			heth->RxDesc = pxDescriptor;
		}
		/* Must be a last segment */
		else
		{
			/* This is the last segment. */
			/* Check if last segment is first segment: one segment contains the frame */
			if( heth->RxFrameInfos.SegCount == 0 )
			{
				/* Remember the first segment. */
				heth->RxFrameInfos.FSRxDesc = pxDescriptor;
			}

			/* Increment segment count */
			heth->RxFrameInfos.SegCount++;

			/* Remember the last segment. */
			heth->RxFrameInfos.LSRxDesc = pxDescriptor;

			/* Get the Frame Length of the received packet: substruct 4 bytes of the CRC */
			heth->RxFrameInfos.length =
				( ( ulStatus & ETH_DMARXDESC_FL ) >> ETH_DMARXDESC_FRAMELENGTHSHIFT ) - 4;

			/* Get the address of the buffer start address */
			heth->RxFrameInfos.buffer = heth->RxFrameInfos.FSRxDesc->Buffer1Addr;

			/* Point to next descriptor */
			heth->RxDesc = ( ETH_DMADescTypeDef * ) pxDescriptor->Buffer2NextDescAddr;

			/* Return OK status: a packet was received. */
			xResult = HAL_OK;
			break;
		}
	}

	/* Set ETH HAL State to Ready */
	heth->State = HAL_ETH_STATE_READY;

	/* Process Unlocked */
	__HAL_UNLOCK( heth );

	/* Return function status */
	return xResult;
}

#if( STM32_ETHERNET_STATS != 0 )

	volatile int rx_count, tx_count, int_count;
	/**
	  * @brief  This function handles ETH interrupt request.
	  * @param  heth: pointer to a ETH_HandleTypeDef structure that contains
	  *         the configuration information for ETHERNET module
	  * @retval HAL status
	  */
	volatile int int_counts[32];
	volatile int tx_status[8];
	volatile unsigned sr_history[32];
	volatile int sr_head;
	#define	STM32_STAT_INC( x )		do { ( x )++; } while( 0 )

#else
	#define	STM32_STAT_INC( x )		do { } while( 0 )
#endif /* STM32_ETHERNET_STATS */

#define ETH_DMA_ALL_INTS \
	( ETH_DMA_IT_TST | ETH_DMA_IT_PMT | ETH_DMA_IT_MMC | ETH_DMA_IT_NIS | ETH_DMA_IT_AIS | ETH_DMA_IT_ER | \
	ETH_DMA_IT_FBE | ETH_DMA_IT_ET | ETH_DMA_IT_RWT | ETH_DMA_IT_RPS | ETH_DMA_IT_RBU | ETH_DMA_IT_R | \
	ETH_DMA_IT_TU | ETH_DMA_IT_RO | ETH_DMA_IT_TJT | ETH_DMA_IT_TPS | ETH_DMA_IT_T )

//#define ETH_DMA_ALL_INTS		ETH_DMA_IT_RBU | ETH_DMA_FLAG_T | ETH_DMA_FLAG_AIS

#define INT_MASK		( ( uint32_t ) ~ ( ETH_DMA_IT_TBU ) )
void HAL_ETH_IRQHandler(ETH_HandleTypeDef *heth)
{
	uint32_t dmasr;

	STM32_STAT_INC( int_count );

	dmasr = heth->Instance->DMASR & ETH_DMA_ALL_INTS;
	heth->Instance->DMASR = dmasr;

#if( STM32_ETHERNET_STATS != 0 )
	if( sr_head < ARRAY_SIZE( sr_history ) )
	{
		sr_history[ sr_head++ ] = dmasr;
	}

	{
		int i;
		for (i = 0; i < 32; i++) {
			if (dmasr & (1u << i)) {
				int_counts[i]++;
			}
		}
		tx_status[ ( dmasr >> 20 ) & 0x07 ]++;
	}
#endif

	/* Frame received */
	if( ( dmasr & ( ETH_DMA_FLAG_R | ETH_DMA_IT_RBU ) ) != 0 )
	{
		/* Receive complete callback */
		HAL_ETH_RxCpltCallback( heth );
		STM32_STAT_INC( rx_count );
	}
	/* Frame transmitted */
	if( ( dmasr & ( ETH_DMA_FLAG_T ) ) != 0 )
	{
		/* Transfer complete callback */
		HAL_ETH_TxCpltCallback( heth );
		STM32_STAT_INC( tx_count );
	}

	/* ETH DMA Error */
	if( ( dmasr & ( ETH_DMA_FLAG_AIS ) ) != 0 )
	{
		/* Ethernet Error callback */
		HAL_ETH_ErrorCallback( heth );
	}
}

/**
  * @brief  Tx Transfer completed callbacks.
  * @param  heth: pointer to a ETH_HandleTypeDef structure that contains
  *         the configuration information for ETHERNET module
  * @retval None
  */
__weak void HAL_ETH_TxCpltCallback(ETH_HandleTypeDef *heth)
{
  /* NOTE : This function Should not be modified, when the callback is needed,
  the HAL_ETH_TxCpltCallback could be implemented in the user file
  */
}

/**
  * @brief  Rx Transfer completed callbacks.
  * @param  heth: pointer to a ETH_HandleTypeDef structure that contains
  *         the configuration information for ETHERNET module
  * @retval None
  */
__weak void HAL_ETH_RxCpltCallback(ETH_HandleTypeDef *heth)
{
  /* NOTE : This function Should not be modified, when the callback is needed,
  the HAL_ETH_TxCpltCallback could be implemented in the user file
  */
}

/**
  * @brief  Ethernet transfer error callbacks
  * @param  heth: pointer to a ETH_HandleTypeDef structure that contains
  *         the configuration information for ETHERNET module
  * @retval None
  */
__weak void HAL_ETH_ErrorCallback(ETH_HandleTypeDef *heth)
{
  /* NOTE : This function Should not be modified, when the callback is needed,
  the HAL_ETH_TxCpltCallback could be implemented in the user file
  */
}

/**
  * @brief  Reads a PHY register
  * @param  heth: pointer to a ETH_HandleTypeDef structure that contains
  *         the configuration information for ETHERNET module
  * @param PHYReg: PHY register address, is the index of one of the 32 PHY register.
  *                This parameter can be one of the following values:
  *                   PHY_BCR: Transceiver Basic Control Register,
  *                   PHY_BSR: Transceiver Basic Status Register.
  *                   More PHY register could be read depending on the used PHY
  * @param RegValue: PHY register value
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_ETH_ReadPHYRegister(ETH_HandleTypeDef *heth, uint16_t PHYReg, uint32_t *RegValue)
{
uint32_t tmpreg = 0;
uint32_t tickstart = 0;
HAL_StatusTypeDef xResult;

	/* Check parameters */
	assert_param(IS_ETH_PHY_ADDRESS(heth->Init.PhyAddress));

	/* Check the ETH peripheral state */
	if( heth->State == HAL_ETH_STATE_BUSY_RD )
	{
		xResult = HAL_BUSY;
	}
	else
	{
		__HAL_LOCK( heth );

		/* Set ETH HAL State to BUSY_RD */
		heth->State = HAL_ETH_STATE_BUSY_RD;

		/* Get the ETHERNET MACMIIAR value */
		tmpreg = heth->Instance->MACMIIAR;

		/* Keep only the CSR Clock Range CR[2:0] bits value */
		tmpreg &= ~ETH_MACMIIAR_CR_MASK;

		/* Prepare the MII address register value */
		tmpreg |= ( ( ( uint32_t )heth->Init.PhyAddress << 11) & ETH_MACMIIAR_PA );    /* Set the PHY device address   */
		tmpreg |= ( ( ( uint32_t )PHYReg << 6 ) & ETH_MACMIIAR_MR );                   /* Set the PHY register address */
		tmpreg &= ~ETH_MACMIIAR_MW;                                           /* Set the read mode            */
		tmpreg |= ETH_MACMIIAR_MB;                                            /* Set the MII Busy bit         */

		/* Write the result value into the MII Address register */
		heth->Instance->MACMIIAR = tmpreg;

		/* Get tick */
		tickstart = HAL_GetTick();

		/* Check for the Busy flag */
		while( 1 )
		{
			tmpreg = heth->Instance->MACMIIAR;

			if( ( tmpreg & ETH_MACMIIAR_MB ) == 0ul )
			{
				/* Get MACMIIDR value */
				*RegValue = ( uint32_t ) heth->Instance->MACMIIDR;
				xResult = HAL_OK;
				break;
			}
			/* Check for the Timeout */
			if( ( HAL_GetTick( ) - tickstart ) > PHY_READ_TO )
			{
				xResult = HAL_TIMEOUT;
				break;
			}

		}

		/* Set ETH HAL State to READY */
		heth->State = HAL_ETH_STATE_READY;

		/* Process Unlocked */
		__HAL_UNLOCK( heth );
	}

	if( xResult != HAL_OK )
	{
		lUDPLoggingPrintf( "ReadPHY: %d\n", xResult );
	}
	/* Return function status */
	return xResult;
}

/**
  * @brief  Writes to a PHY register.
  * @param  heth: pointer to a ETH_HandleTypeDef structure that contains
  *         the configuration information for ETHERNET module
  * @param  PHYReg: PHY register address, is the index of one of the 32 PHY register.
  *          This parameter can be one of the following values:
  *             PHY_BCR: Transceiver Control Register.
  *             More PHY register could be written depending on the used PHY
  * @param  RegValue: the value to write
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_ETH_WritePHYRegister(ETH_HandleTypeDef *heth, uint16_t PHYReg, uint32_t RegValue)
{
uint32_t tmpreg = 0;
uint32_t tickstart = 0;
HAL_StatusTypeDef xResult;

	/* Check parameters */
	assert_param( IS_ETH_PHY_ADDRESS( heth->Init.PhyAddress ) );

	/* Check the ETH peripheral state */
	if( heth->State == HAL_ETH_STATE_BUSY_WR )
	{
		xResult = HAL_BUSY;
	}
	else
	{
		__HAL_LOCK( heth );

		/* Set ETH HAL State to BUSY_WR */
		heth->State = HAL_ETH_STATE_BUSY_WR;

		/* Get the ETHERNET MACMIIAR value */
		tmpreg = heth->Instance->MACMIIAR;

		/* Keep only the CSR Clock Range CR[2:0] bits value */
		tmpreg &= ~ETH_MACMIIAR_CR_MASK;

		/* Prepare the MII register address value */
		tmpreg |= ( ( ( uint32_t ) heth->Init.PhyAddress << 11 ) & ETH_MACMIIAR_PA ); /* Set the PHY device address */
		tmpreg |= ( ( ( uint32_t ) PHYReg << 6 ) & ETH_MACMIIAR_MR );                 /* Set the PHY register address */
		tmpreg |= ETH_MACMIIAR_MW;                                          /* Set the write mode */
		tmpreg |= ETH_MACMIIAR_MB;                                          /* Set the MII Busy bit */

		/* Give the value to the MII data register */
		heth->Instance->MACMIIDR = ( uint16_t ) RegValue;

		/* Write the result value into the MII Address register */
		heth->Instance->MACMIIAR = tmpreg;

		/* Get tick */
		tickstart = HAL_GetTick();

		/* Check for the Busy flag */
		while( 1 )
		{
			tmpreg = heth->Instance->MACMIIAR;

			if( ( tmpreg & ETH_MACMIIAR_MB ) == 0ul )
			{
				xResult = HAL_OK;
				break;
			}
			/* Check for the Timeout */
			if( ( HAL_GetTick( ) - tickstart ) > PHY_WRITE_TO )
			{
				xResult = HAL_TIMEOUT;
				break;
			}
		}

		/* Set ETH HAL State to READY */
		heth->State = HAL_ETH_STATE_READY;
		/* Process Unlocked */
		__HAL_UNLOCK( heth );
	}

	if( xResult != HAL_OK )
	{
		lUDPLoggingPrintf( "WritePHY: %d\n", xResult );
	}
	/* Return function status */
	return xResult;
}

/**
  * @}
  */

/** @defgroup ETH_Exported_Functions_Group3 Peripheral Control functions
 *  @brief    Peripheral Control functions
 *
@verbatim
 ===============================================================================
                  ##### Peripheral Control functions #####
 ===============================================================================
    [..]  This section provides functions allowing to:
      (+) Enable MAC and DMA transmission and reception.
          HAL_ETH_Start();
      (+) Disable MAC and DMA transmission and reception.
          HAL_ETH_Stop();
      (+) Set the MAC configuration in runtime mode
          HAL_ETH_ConfigMAC();
      (+) Set the DMA configuration in runtime mode
          HAL_ETH_ConfigDMA();

@endverbatim
  * @{
  */

 /**
  * @brief  Enables Ethernet MAC and DMA reception/transmission
  * @param  heth: pointer to a ETH_HandleTypeDef structure that contains
  *         the configuration information for ETHERNET module
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_ETH_Start( ETH_HandleTypeDef *heth )
{
	/* Process Locked */
	__HAL_LOCK( heth );

	/* Set the ETH peripheral state to BUSY */
	heth->State = HAL_ETH_STATE_BUSY;

	/* Enable transmit state machine of the MAC for transmission on the MII */
	ETH_MACTransmissionEnable( heth );

	/* Enable receive state machine of the MAC for reception from the MII */
	ETH_MACReceptionEnable( heth );

	/* Flush Transmit FIFO */
	ETH_FlushTransmitFIFO( heth );

	/* Start DMA transmission */
	ETH_DMATransmissionEnable( heth );

	/* Start DMA reception */
	ETH_DMAReceptionEnable( heth );

	/* Set the ETH state to READY*/
	heth->State= HAL_ETH_STATE_READY;

	/* Process Unlocked */
	__HAL_UNLOCK( heth );

	/* Return function status */
	return HAL_OK;
}

/**
  * @brief  Stop Ethernet MAC and DMA reception/transmission
  * @param  heth: pointer to a ETH_HandleTypeDef structure that contains
  *         the configuration information for ETHERNET module
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_ETH_Stop(ETH_HandleTypeDef *heth)
{
  /* Process Locked */
  __HAL_LOCK( heth );

  /* Set the ETH peripheral state to BUSY */
  heth->State = HAL_ETH_STATE_BUSY;

  /* Stop DMA transmission */
  ETH_DMATransmissionDisable( heth );

  /* Stop DMA reception */
  ETH_DMAReceptionDisable( heth );

  /* Disable receive state machine of the MAC for reception from the MII */
  ETH_MACReceptionDisable( heth );

  /* Flush Transmit FIFO */
  ETH_FlushTransmitFIFO( heth );

  /* Disable transmit state machine of the MAC for transmission on the MII */
  ETH_MACTransmissionDisable( heth );

  /* Set the ETH state*/
  heth->State = HAL_ETH_STATE_READY;

  /* Process Unlocked */
  __HAL_UNLOCK( heth );

  /* Return function status */
  return HAL_OK;
}

static void prvWriteMACFCR( ETH_HandleTypeDef *heth, uint32_t ulValue)
{
	/* Enable the MAC transmission */
	heth->Instance->MACFCR = ulValue;

	/* Wait until the write operation will be taken into account:
	at least four TX_CLK/RX_CLK clock cycles.
	Read it back, wait a ms and */
	( void ) heth->Instance->MACFCR;

	HAL_Delay( ETH_REG_WRITE_DELAY );

	heth->Instance->MACFCR = ulValue;
}

static void prvWriteDMAOMR( ETH_HandleTypeDef *heth, uint32_t ulValue)
{
	/* Enable the MAC transmission */
	heth->Instance->DMAOMR = ulValue;

	/* Wait until the write operation will be taken into account:
	at least four TX_CLK/RX_CLK clock cycles.
	Read it back, wait a ms and */
	( void ) heth->Instance->DMAOMR;

	HAL_Delay( ETH_REG_WRITE_DELAY );

	heth->Instance->DMAOMR = ulValue;
}

static void prvWriteMACCR( ETH_HandleTypeDef *heth, uint32_t ulValue)
{
	/* Enable the MAC transmission */
	heth->Instance->MACCR = ulValue;

	/* Wait until the write operation will be taken into account:
	at least four TX_CLK/RX_CLK clock cycles.
	Read it back, wait a ms and */
	( void ) heth->Instance->MACCR;

	HAL_Delay( ETH_REG_WRITE_DELAY );

	heth->Instance->MACCR = ulValue;
}

/**
  * @brief  Set ETH MAC Configuration.
  * @param  heth: pointer to a ETH_HandleTypeDef structure that contains
  *         the configuration information for ETHERNET module
  * @param  macconf: MAC Configuration structure
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_ETH_ConfigMAC(ETH_HandleTypeDef *heth, ETH_MACInitTypeDef *macconf)
{
	uint32_t tmpreg = 0;

	/* Process Locked */
	__HAL_LOCK( heth );

	/* Set the ETH peripheral state to BUSY */
	heth->State= HAL_ETH_STATE_BUSY;

	assert_param(IS_ETH_SPEED(heth->Init.Speed));
	assert_param(IS_ETH_DUPLEX_MODE(heth->Init.DuplexMode));

	if (macconf != NULL)
	{
		/* Check the parameters */
		assert_param(IS_ETH_WATCHDOG(macconf->Watchdog));
		assert_param(IS_ETH_JABBER(macconf->Jabber));
		assert_param(IS_ETH_INTER_FRAME_GAP(macconf->InterFrameGap));
		assert_param(IS_ETH_CARRIER_SENSE(macconf->CarrierSense));
		assert_param(IS_ETH_RECEIVE_OWN(macconf->ReceiveOwn));
		assert_param(IS_ETH_LOOPBACK_MODE(macconf->LoopbackMode));
		assert_param(IS_ETH_CHECKSUM_OFFLOAD(macconf->ChecksumOffload));
		assert_param(IS_ETH_RETRY_TRANSMISSION(macconf->RetryTransmission));
		assert_param(IS_ETH_AUTOMATIC_PADCRC_STRIP(macconf->AutomaticPadCRCStrip));
		assert_param(IS_ETH_BACKOFF_LIMIT(macconf->BackOffLimit));
		assert_param(IS_ETH_DEFERRAL_CHECK(macconf->DeferralCheck));
		assert_param(IS_ETH_RECEIVE_ALL(macconf->ReceiveAll));
		assert_param(IS_ETH_SOURCE_ADDR_FILTER(macconf->SourceAddrFilter));
		assert_param(IS_ETH_CONTROL_FRAMES(macconf->PassControlFrames));
		assert_param(IS_ETH_BROADCAST_FRAMES_RECEPTION(macconf->BroadcastFramesReception));
		assert_param(IS_ETH_DESTINATION_ADDR_FILTER(macconf->DestinationAddrFilter));
		assert_param(IS_ETH_PROMISCUOUS_MODE(macconf->PromiscuousMode));
		assert_param(IS_ETH_MULTICAST_FRAMES_FILTER(macconf->MulticastFramesFilter));
		assert_param(IS_ETH_UNICAST_FRAMES_FILTER(macconf->UnicastFramesFilter));
		assert_param(IS_ETH_PAUSE_TIME(macconf->PauseTime));
		assert_param(IS_ETH_ZEROQUANTA_PAUSE(macconf->ZeroQuantaPause));
		assert_param(IS_ETH_PAUSE_LOW_THRESHOLD(macconf->PauseLowThreshold));
		assert_param(IS_ETH_UNICAST_PAUSE_FRAME_DETECT(macconf->UnicastPauseFrameDetect));
		assert_param(IS_ETH_RECEIVE_FLOWCONTROL(macconf->ReceiveFlowControl));
		assert_param(IS_ETH_TRANSMIT_FLOWCONTROL(macconf->TransmitFlowControl));
		assert_param(IS_ETH_VLAN_TAG_COMPARISON(macconf->VLANTagComparison));
		assert_param(IS_ETH_VLAN_TAG_IDENTIFIER(macconf->VLANTagIdentifier));

		/*------------------------ ETHERNET MACCR Configuration --------------------*/
		/* Get the ETHERNET MACCR value */
		tmpreg = heth->Instance->MACCR;
		/* Clear WD, PCE, PS, TE and RE bits */
		tmpreg &= ETH_MACCR_CLEAR_MASK;

		tmpreg |= (uint32_t)(
			macconf->Watchdog |
			macconf->Jabber |
			macconf->InterFrameGap |
			macconf->CarrierSense |
			heth->Init.Speed |
			macconf->ReceiveOwn |
			macconf->LoopbackMode |
			heth->Init.DuplexMode |
			macconf->ChecksumOffload |
			macconf->RetryTransmission |
			macconf->AutomaticPadCRCStrip |
			macconf->BackOffLimit |
			macconf->DeferralCheck);

		/* Write to ETHERNET MACCR */
		prvWriteMACCR( heth, tmpreg );

		/*----------------------- ETHERNET MACFFR Configuration --------------------*/
		/* Write to ETHERNET MACFFR */
		heth->Instance->MACFFR = (uint32_t)(
			macconf->ReceiveAll |
			macconf->SourceAddrFilter |
			macconf->PassControlFrames |
			macconf->BroadcastFramesReception |
			macconf->DestinationAddrFilter |
			macconf->PromiscuousMode |
			macconf->MulticastFramesFilter |
			macconf->UnicastFramesFilter);

		/* Wait until the write operation will be taken into account :
		at least four TX_CLK/RX_CLK clock cycles */
		tmpreg = heth->Instance->MACFFR;
		HAL_Delay(ETH_REG_WRITE_DELAY);
		heth->Instance->MACFFR = tmpreg;

		/*--------------- ETHERNET MACHTHR and MACHTLR Configuration ---------------*/
		/* Write to ETHERNET MACHTHR */
		heth->Instance->MACHTHR = (uint32_t)macconf->HashTableHigh;

		/* Write to ETHERNET MACHTLR */
		heth->Instance->MACHTLR = (uint32_t)macconf->HashTableLow;
		/*----------------------- ETHERNET MACFCR Configuration --------------------*/

		/* Get the ETHERNET MACFCR value */
		tmpreg = heth->Instance->MACFCR;
		/* Clear xx bits */
		tmpreg &= ETH_MACFCR_CLEAR_MASK;

		tmpreg |= (uint32_t)((
			macconf->PauseTime << 16) |
			macconf->ZeroQuantaPause |
			macconf->PauseLowThreshold |
			macconf->UnicastPauseFrameDetect |
			macconf->ReceiveFlowControl |
			macconf->TransmitFlowControl);

		/* Write to ETHERNET MACFCR */
		prvWriteMACFCR( heth, tmpreg );

		/*----------------------- ETHERNET MACVLANTR Configuration -----------------*/
		heth->Instance->MACVLANTR = (uint32_t)(macconf->VLANTagComparison |
		macconf->VLANTagIdentifier);

		/* Wait until the write operation will be taken into account :
		at least four TX_CLK/RX_CLK clock cycles */
		tmpreg = heth->Instance->MACVLANTR;
		HAL_Delay(ETH_REG_WRITE_DELAY);
		heth->Instance->MACVLANTR = tmpreg;
	}
	else /* macconf == NULL : here we just configure Speed and Duplex mode */
	{
		/*------------------------ ETHERNET MACCR Configuration --------------------*/
		/* Get the ETHERNET MACCR value */
		tmpreg = heth->Instance->MACCR;

		/* Clear FES and DM bits */
		tmpreg &= ~((uint32_t)0x00004800);

		tmpreg |= (uint32_t)(heth->Init.Speed | heth->Init.DuplexMode);

		/* Write to ETHERNET MACCR */
		prvWriteMACCR( heth, tmpreg );
	}

	/* Set the ETH state to Ready */
	heth->State= HAL_ETH_STATE_READY;

	/* Process Unlocked */
	__HAL_UNLOCK( heth );

	/* Return function status */
	return HAL_OK;
}

/**
  * @brief  Sets ETH DMA Configuration.
  * @param  heth: pointer to a ETH_HandleTypeDef structure that contains
  *         the configuration information for ETHERNET module
  * @param  dmaconf: DMA Configuration structure
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_ETH_ConfigDMA(ETH_HandleTypeDef *heth, ETH_DMAInitTypeDef *dmaconf)
{
	uint32_t tmpreg = 0;

	/* Process Locked */
	__HAL_LOCK( heth );

	/* Set the ETH peripheral state to BUSY */
	heth->State= HAL_ETH_STATE_BUSY;

	/* Check parameters */
	assert_param(IS_ETH_DROP_TCPIP_CHECKSUM_FRAME(dmaconf->DropTCPIPChecksumErrorFrame));
	assert_param(IS_ETH_RECEIVE_STORE_FORWARD(dmaconf->ReceiveStoreForward));
	assert_param(IS_ETH_FLUSH_RECEIVE_FRAME(dmaconf->FlushReceivedFrame));
	assert_param(IS_ETH_TRANSMIT_STORE_FORWARD(dmaconf->TransmitStoreForward));
	assert_param(IS_ETH_TRANSMIT_THRESHOLD_CONTROL(dmaconf->TransmitThresholdControl));
	assert_param(IS_ETH_FORWARD_ERROR_FRAMES(dmaconf->ForwardErrorFrames));
	assert_param(IS_ETH_FORWARD_UNDERSIZED_GOOD_FRAMES(dmaconf->ForwardUndersizedGoodFrames));
	assert_param(IS_ETH_RECEIVE_THRESHOLD_CONTROL(dmaconf->ReceiveThresholdControl));
	assert_param(IS_ETH_SECOND_FRAME_OPERATE(dmaconf->SecondFrameOperate));
	assert_param(IS_ETH_ADDRESS_ALIGNED_BEATS(dmaconf->AddressAlignedBeats));
	assert_param(IS_ETH_FIXED_BURST(dmaconf->FixedBurst));
	assert_param(IS_ETH_RXDMA_BURST_LENGTH(dmaconf->RxDMABurstLength));
	assert_param(IS_ETH_TXDMA_BURST_LENGTH(dmaconf->TxDMABurstLength));
	assert_param(IS_ETH_ENHANCED_DESCRIPTOR_FORMAT(dmaconf->EnhancedDescriptorFormat));
	assert_param(IS_ETH_DMA_DESC_SKIP_LENGTH(dmaconf->DescriptorSkipLength));
	assert_param(IS_ETH_DMA_ARBITRATION_ROUNDROBIN_RXTX(dmaconf->DMAArbitration));

	/*----------------------- ETHERNET DMAOMR Configuration --------------------*/
	/* Get the ETHERNET DMAOMR value */
	tmpreg = heth->Instance->DMAOMR;
	/* Clear xx bits */
	tmpreg &= ETH_DMAOMR_CLEAR_MASK;

	tmpreg |= (uint32_t)(
		dmaconf->DropTCPIPChecksumErrorFrame |
		dmaconf->ReceiveStoreForward |
		dmaconf->FlushReceivedFrame |
		dmaconf->TransmitStoreForward |
		dmaconf->TransmitThresholdControl |
		dmaconf->ForwardErrorFrames |
		dmaconf->ForwardUndersizedGoodFrames |
		dmaconf->ReceiveThresholdControl |
		dmaconf->SecondFrameOperate);

	/* Write to ETHERNET DMAOMR */
	prvWriteDMAOMR( heth, tmpreg );

	/*----------------------- ETHERNET DMABMR Configuration --------------------*/
	heth->Instance->DMABMR = (uint32_t)(dmaconf->AddressAlignedBeats |
	dmaconf->FixedBurst |
	dmaconf->RxDMABurstLength | /* !! if 4xPBL is selected for Tx or Rx it is applied for the other */
	dmaconf->TxDMABurstLength |
	dmaconf->EnhancedDescriptorFormat |
	(dmaconf->DescriptorSkipLength << 2) |
	dmaconf->DMAArbitration |
	ETH_DMABMR_USP); /* Enable use of separate PBL for Rx and Tx */

	/* Wait until the write operation will be taken into account:
	at least four TX_CLK/RX_CLK clock cycles */
	tmpreg = heth->Instance->DMABMR;
	HAL_Delay(ETH_REG_WRITE_DELAY);
	heth->Instance->DMABMR = tmpreg;

	/* Set the ETH state to Ready */
	heth->State= HAL_ETH_STATE_READY;

	/* Process Unlocked */
	__HAL_UNLOCK( heth );

	/* Return function status */
	return HAL_OK;
}

/**
  * @}
  */

/** @defgroup ETH_Exported_Functions_Group4 Peripheral State functions
  *  @brief   Peripheral State functions
  *
  @verbatim
  ===============================================================================
                         ##### Peripheral State functions #####
  ===============================================================================
  [..]
  This subsection permits to get in run-time the status of the peripheral
  and the data flow.
       (+) Get the ETH handle state:
           HAL_ETH_GetState();


  @endverbatim
  * @{
  */

/**
  * @brief  Return the ETH HAL state
  * @param  heth: pointer to a ETH_HandleTypeDef structure that contains
  *         the configuration information for ETHERNET module
  * @retval HAL state
  */
HAL_ETH_StateTypeDef HAL_ETH_GetState(ETH_HandleTypeDef *heth)
{
  /* Return ETH state */
  return heth->State;
}

/**
  * @}
  */

/**
  * @}
  */

/** @addtogroup ETH_Private_Functions
  * @{
  */

/**
  * @brief  Configures Ethernet MAC and DMA with default parameters.
  * @param  heth: pointer to a ETH_HandleTypeDef structure that contains
  *         the configuration information for ETHERNET module
  * @param  err: Ethernet Init error
  * @retval HAL status
  */
static void ETH_MACDMAConfig(ETH_HandleTypeDef *heth, uint32_t err)
{
  ETH_MACInitTypeDef macinit;
  ETH_DMAInitTypeDef dmainit;
  uint32_t tmpreg = 0;

  if (err != ETH_SUCCESS) /* Auto-negotiation failed */
  {
    /* Set Ethernet duplex mode to Full-duplex */
    heth->Init.DuplexMode = ETH_MODE_FULLDUPLEX;

    /* Set Ethernet speed to 100M */
    heth->Init.Speed = ETH_SPEED_100M;
  }

  /* Ethernet MAC default initialization **************************************/
  macinit.Watchdog = ETH_WATCHDOG_ENABLE;
  macinit.Jabber = ETH_JABBER_ENABLE;
  macinit.InterFrameGap = ETH_INTERFRAMEGAP_96BIT;
  macinit.CarrierSense = ETH_CARRIERSENCE_ENABLE;
  macinit.ReceiveOwn = ETH_RECEIVEOWN_ENABLE;
  macinit.LoopbackMode = ETH_LOOPBACKMODE_DISABLE;
  if(heth->Init.ChecksumMode == ETH_CHECKSUM_BY_HARDWARE)
  {
    macinit.ChecksumOffload = ETH_CHECKSUMOFFLAOD_ENABLE;
  }
  else
  {
    macinit.ChecksumOffload = ETH_CHECKSUMOFFLAOD_DISABLE;
  }
  macinit.RetryTransmission = ETH_RETRYTRANSMISSION_DISABLE;
  macinit.AutomaticPadCRCStrip = ETH_AUTOMATICPADCRCSTRIP_DISABLE;
  macinit.BackOffLimit = ETH_BACKOFFLIMIT_10;
  macinit.DeferralCheck = ETH_DEFFERRALCHECK_DISABLE;
  macinit.ReceiveAll = ETH_RECEIVEAll_DISABLE;
  macinit.SourceAddrFilter = ETH_SOURCEADDRFILTER_DISABLE;
  macinit.PassControlFrames = ETH_PASSCONTROLFRAMES_BLOCKALL;
  macinit.BroadcastFramesReception = ETH_BROADCASTFRAMESRECEPTION_ENABLE;
  macinit.DestinationAddrFilter = ETH_DESTINATIONADDRFILTER_NORMAL;
  macinit.PromiscuousMode = ETH_PROMISCUOUS_MODE_DISABLE;
  macinit.MulticastFramesFilter = ETH_MULTICASTFRAMESFILTER_PERFECT;
  macinit.UnicastFramesFilter = ETH_UNICASTFRAMESFILTER_PERFECT;
  macinit.HashTableHigh = 0x0;
  macinit.HashTableLow = 0x0;
  macinit.PauseTime = 0x0;
  macinit.ZeroQuantaPause = ETH_ZEROQUANTAPAUSE_DISABLE;
  macinit.PauseLowThreshold = ETH_PAUSELOWTHRESHOLD_MINUS4;
  macinit.UnicastPauseFrameDetect = ETH_UNICASTPAUSEFRAMEDETECT_DISABLE;
  macinit.ReceiveFlowControl = ETH_RECEIVEFLOWCONTROL_DISABLE;
  macinit.TransmitFlowControl = ETH_TRANSMITFLOWCONTROL_DISABLE;
  macinit.VLANTagComparison = ETH_VLANTAGCOMPARISON_16BIT;
  macinit.VLANTagIdentifier = 0x0;

  /*------------------------ ETHERNET MACCR Configuration --------------------*/
  /* Get the ETHERNET MACCR value */
  tmpreg = heth->Instance->MACCR;
  /* Clear WD, PCE, PS, TE and RE bits */
  tmpreg &= ETH_MACCR_CLEAR_MASK;
  /* Set the WD bit according to ETH Watchdog value */
  /* Set the JD: bit according to ETH Jabber value */
  /* Set the IFG bit according to ETH InterFrameGap value */
  /* Set the DCRS bit according to ETH CarrierSense value */
  /* Set the FES bit according to ETH Speed value */
  /* Set the DO bit according to ETH ReceiveOwn value */
  /* Set the LM bit according to ETH LoopbackMode value */
  /* Set the DM bit according to ETH Mode value */
  /* Set the IPCO bit according to ETH ChecksumOffload value */
  /* Set the DR bit according to ETH RetryTransmission value */
  /* Set the ACS bit according to ETH AutomaticPadCRCStrip value */
  /* Set the BL bit according to ETH BackOffLimit value */
  /* Set the DC bit according to ETH DeferralCheck value */
  tmpreg |= (uint32_t)(macinit.Watchdog |
                       macinit.Jabber |
                       macinit.InterFrameGap |
                       macinit.CarrierSense |
                       heth->Init.Speed |
                       macinit.ReceiveOwn |
                       macinit.LoopbackMode |
                       heth->Init.DuplexMode |
                       macinit.ChecksumOffload |
                       macinit.RetryTransmission |
                       macinit.AutomaticPadCRCStrip |
                       macinit.BackOffLimit |
                       macinit.DeferralCheck);

  /* Write to ETHERNET MACCR */
  prvWriteMACCR( heth, tmpreg );

  /*----------------------- ETHERNET MACFFR Configuration --------------------*/
  /* Set the RA bit according to ETH ReceiveAll value */
  /* Set the SAF and SAIF bits according to ETH SourceAddrFilter value */
  /* Set the PCF bit according to ETH PassControlFrames value */
  /* Set the DBF bit according to ETH BroadcastFramesReception value */
  /* Set the DAIF bit according to ETH DestinationAddrFilter value */
  /* Set the PR bit according to ETH PromiscuousMode value */
  /* Set the PM, HMC and HPF bits according to ETH MulticastFramesFilter value */
  /* Set the HUC and HPF bits according to ETH UnicastFramesFilter value */
  /* Write to ETHERNET MACFFR */
  heth->Instance->MACFFR = (uint32_t)(macinit.ReceiveAll |
                                        macinit.SourceAddrFilter |
                                        macinit.PassControlFrames |
                                        macinit.BroadcastFramesReception |
                                        macinit.DestinationAddrFilter |
                                        macinit.PromiscuousMode |
                                        macinit.MulticastFramesFilter |
                                        macinit.UnicastFramesFilter);

   /* Wait until the write operation will be taken into account:
      at least four TX_CLK/RX_CLK clock cycles */
   tmpreg = heth->Instance->MACFFR;
   HAL_Delay(ETH_REG_WRITE_DELAY);
   heth->Instance->MACFFR = tmpreg;

   /*--------------- ETHERNET MACHTHR and MACHTLR Configuration --------------*/
   /* Write to ETHERNET MACHTHR */
   heth->Instance->MACHTHR = (uint32_t)macinit.HashTableHigh;

   /* Write to ETHERNET MACHTLR */
   heth->Instance->MACHTLR = (uint32_t)macinit.HashTableLow;
   /*----------------------- ETHERNET MACFCR Configuration -------------------*/

   /* Get the ETHERNET MACFCR value */
   tmpreg = heth->Instance->MACFCR;
   /* Clear xx bits */
   tmpreg &= ETH_MACFCR_CLEAR_MASK;

   /* Set the PT bit according to ETH PauseTime value */
   /* Set the DZPQ bit according to ETH ZeroQuantaPause value */
   /* Set the PLT bit according to ETH PauseLowThreshold value */
   /* Set the UP bit according to ETH UnicastPauseFrameDetect value */
   /* Set the RFE bit according to ETH ReceiveFlowControl value */
   /* Set the TFE bit according to ETH TransmitFlowControl value */
   tmpreg |= (uint32_t)((macinit.PauseTime << 16) |
                        macinit.ZeroQuantaPause |
                        macinit.PauseLowThreshold |
                        macinit.UnicastPauseFrameDetect |
                        macinit.ReceiveFlowControl |
                        macinit.TransmitFlowControl);

   /* Write to ETHERNET MACFCR */
   prvWriteMACFCR( heth, tmpreg );

   /*----------------------- ETHERNET MACVLANTR Configuration ----------------*/
   /* Set the ETV bit according to ETH VLANTagComparison value */
   /* Set the VL bit according to ETH VLANTagIdentifier value */
   heth->Instance->MACVLANTR = (uint32_t)(macinit.VLANTagComparison |
                                            macinit.VLANTagIdentifier);

    /* Wait until the write operation will be taken into account:
       at least four TX_CLK/RX_CLK clock cycles */
    tmpreg = heth->Instance->MACVLANTR;
    HAL_Delay(ETH_REG_WRITE_DELAY);
    heth->Instance->MACVLANTR = tmpreg;

    /* Ethernet DMA default initialization ************************************/
    dmainit.DropTCPIPChecksumErrorFrame = ETH_DROPTCPIPCHECKSUMERRORFRAME_ENABLE;
    dmainit.ReceiveStoreForward = ETH_RECEIVESTOREFORWARD_ENABLE;
    dmainit.FlushReceivedFrame = ETH_FLUSHRECEIVEDFRAME_ENABLE;
    dmainit.TransmitStoreForward = ETH_TRANSMITSTOREFORWARD_ENABLE;
    dmainit.TransmitThresholdControl = ETH_TRANSMITTHRESHOLDCONTROL_64BYTES;
    dmainit.ForwardErrorFrames = ETH_FORWARDERRORFRAMES_DISABLE;
    dmainit.ForwardUndersizedGoodFrames = ETH_FORWARDUNDERSIZEDGOODFRAMES_DISABLE;
    dmainit.ReceiveThresholdControl = ETH_RECEIVEDTHRESHOLDCONTROL_64BYTES;
    dmainit.SecondFrameOperate = ETH_SECONDFRAMEOPERARTE_ENABLE;
    dmainit.AddressAlignedBeats = ETH_ADDRESSALIGNEDBEATS_ENABLE;
    dmainit.FixedBurst = ETH_FIXEDBURST_ENABLE;
    dmainit.RxDMABurstLength = ETH_RXDMABURSTLENGTH_32BEAT;
    dmainit.TxDMABurstLength = ETH_TXDMABURSTLENGTH_32BEAT;
    dmainit.EnhancedDescriptorFormat = ETH_DMAENHANCEDDESCRIPTOR_ENABLE;
    dmainit.DescriptorSkipLength = 0x0;
    dmainit.DMAArbitration = ETH_DMAARBITRATION_ROUNDROBIN_RXTX_1_1;

    /* Get the ETHERNET DMAOMR value */
    tmpreg = heth->Instance->DMAOMR;
    /* Clear xx bits */
    tmpreg &= ETH_DMAOMR_CLEAR_MASK;

    /* Set the DT bit according to ETH DropTCPIPChecksumErrorFrame value */
    /* Set the RSF bit according to ETH ReceiveStoreForward value */
    /* Set the DFF bit according to ETH FlushReceivedFrame value */
    /* Set the TSF bit according to ETH TransmitStoreForward value */
    /* Set the TTC bit according to ETH TransmitThresholdControl value */
    /* Set the FEF bit according to ETH ForwardErrorFrames value */
    /* Set the FUF bit according to ETH ForwardUndersizedGoodFrames value */
    /* Set the RTC bit according to ETH ReceiveThresholdControl value */
    /* Set the OSF bit according to ETH SecondFrameOperate value */
    tmpreg |= (uint32_t)(dmainit.DropTCPIPChecksumErrorFrame |
                         dmainit.ReceiveStoreForward |
                         dmainit.FlushReceivedFrame |
                         dmainit.TransmitStoreForward |
                         dmainit.TransmitThresholdControl |
                         dmainit.ForwardErrorFrames |
                         dmainit.ForwardUndersizedGoodFrames |
                         dmainit.ReceiveThresholdControl |
                         dmainit.SecondFrameOperate);

    /* Write to ETHERNET DMAOMR */
    prvWriteDMAOMR( heth, tmpreg );

    /*----------------------- ETHERNET DMABMR Configuration ------------------*/
    /* Set the AAL bit according to ETH AddressAlignedBeats value */
    /* Set the FB bit according to ETH FixedBurst value */
    /* Set the RPBL and 4*PBL bits according to ETH RxDMABurstLength value */
    /* Set the PBL and 4*PBL bits according to ETH TxDMABurstLength value */
    /* Set the Enhanced DMA descriptors bit according to ETH EnhancedDescriptorFormat value*/
    /* Set the DSL bit according to ETH DesciptorSkipLength value */
    /* Set the PR and DA bits according to ETH DMAArbitration value */
    heth->Instance->DMABMR = (uint32_t)(dmainit.AddressAlignedBeats |
                                          dmainit.FixedBurst |
                                          dmainit.RxDMABurstLength |    /* !! if 4xPBL is selected for Tx or Rx it is applied for the other */
                                          dmainit.TxDMABurstLength |
                                          dmainit.EnhancedDescriptorFormat |
                                          (dmainit.DescriptorSkipLength << 2) |
                                          dmainit.DMAArbitration |
                                          ETH_DMABMR_USP); /* Enable use of separate PBL for Rx and Tx */

     /* Wait until the write operation will be taken into account:
        at least four TX_CLK/RX_CLK clock cycles */
     tmpreg = heth->Instance->DMABMR;
     HAL_Delay(ETH_REG_WRITE_DELAY);
     heth->Instance->DMABMR = tmpreg;

     if(heth->Init.RxMode == ETH_RXINTERRUPT_MODE)
     {
       /* Enable the Ethernet Rx Interrupt */
       __HAL_ETH_DMA_ENABLE_IT(( heth ), ETH_DMA_IT_NIS | ETH_DMA_IT_R);
     }

     /* Initialize MAC address in ethernet MAC */
     ETH_MACAddressConfig(heth, ETH_MAC_ADDRESS0, heth->Init.MACAddr);
}

/**
  * @brief  Configures the selected MAC address.
  * @param  heth: pointer to a ETH_HandleTypeDef structure that contains
  *         the configuration information for ETHERNET module
  * @param  MacAddr: The MAC address to configure
  *          This parameter can be one of the following values:
  *             @arg ETH_MAC_Address0: MAC Address0
  *             @arg ETH_MAC_Address1: MAC Address1
  *             @arg ETH_MAC_Address2: MAC Address2
  *             @arg ETH_MAC_Address3: MAC Address3
  * @param  Addr: Pointer to MAC address buffer data (6 bytes)
  * @retval HAL status
  */
static void ETH_MACAddressConfig(ETH_HandleTypeDef *heth, uint32_t MacAddr, uint8_t *Addr)
{
	uint32_t tmpreg;

	/* Check the parameters */
	assert_param( IS_ETH_MAC_ADDRESS0123( MacAddr ) );

	/* Calculate the selected MAC address high register */
	tmpreg = 0x80000000ul | ( ( uint32_t )Addr[ 5 ] << 8) | (uint32_t)Addr[ 4 ];
	/* Load the selected MAC address high register */
	( * ( __IO uint32_t * ) ( ( uint32_t ) ( ETH_MAC_ADDR_HBASE + MacAddr ) ) ) = tmpreg;
	/* Calculate the selected MAC address low register */
	tmpreg = ( ( uint32_t )Addr[ 3 ] << 24 ) | ( ( uint32_t )Addr[ 2 ] << 16 ) | ( ( uint32_t )Addr[ 1 ] << 8 ) | Addr[ 0 ];

	/* Load the selected MAC address low register */
	( * ( __IO uint32_t * ) ( ( uint32_t ) ( ETH_MAC_ADDR_LBASE + MacAddr ) ) ) = tmpreg;
}

/**
  * @brief  Enables the MAC transmission.
  * @param  heth: pointer to a ETH_HandleTypeDef structure that contains
  *         the configuration information for ETHERNET module
  * @retval None
  */
static void ETH_MACTransmissionEnable(ETH_HandleTypeDef *heth)
{
	uint32_t tmpreg = heth->Instance->MACCR | ETH_MACCR_TE;

	prvWriteMACCR( heth, tmpreg );
}

/**
  * @brief  Disables the MAC transmission.
  * @param  heth: pointer to a ETH_HandleTypeDef structure that contains
  *         the configuration information for ETHERNET module
  * @retval None
  */
static void ETH_MACTransmissionDisable(ETH_HandleTypeDef *heth)
{
	uint32_t tmpreg = heth->Instance->MACCR & ~( ETH_MACCR_TE );

	prvWriteMACCR( heth, tmpreg );
}

/**
  * @brief  Enables the MAC reception.
  * @param  heth: pointer to a ETH_HandleTypeDef structure that contains
  *         the configuration information for ETHERNET module
  * @retval None
  */
static void ETH_MACReceptionEnable(ETH_HandleTypeDef *heth)
{
	__IO uint32_t tmpreg = heth->Instance->MACCR | ETH_MACCR_RE;

	prvWriteMACCR( heth, tmpreg );
}

/**
  * @brief  Disables the MAC reception.
  * @param  heth: pointer to a ETH_HandleTypeDef structure that contains
  *         the configuration information for ETHERNET module
  * @retval None
  */
static void ETH_MACReceptionDisable(ETH_HandleTypeDef *heth)
{
	__IO uint32_t tmpreg = heth->Instance->MACCR & ~( ETH_MACCR_RE );

	prvWriteMACCR( heth, tmpreg );
}

/**
  * @brief  Enables the DMA transmission.
  * @param  heth: pointer to a ETH_HandleTypeDef structure that contains
  *         the configuration information for ETHERNET module
  * @retval None
  */
static void ETH_DMATransmissionEnable(ETH_HandleTypeDef *heth)
{
	/* Enable the DMA transmission */
	__IO uint32_t tmpreg = heth->Instance->DMAOMR | ETH_DMAOMR_ST;

	prvWriteDMAOMR( heth, tmpreg );
}

/**
  * @brief  Disables the DMA transmission.
  * @param  heth: pointer to a ETH_HandleTypeDef structure that contains
  *         the configuration information for ETHERNET module
  * @retval None
  */
static void ETH_DMATransmissionDisable(ETH_HandleTypeDef *heth)
{
	/* Disable the DMA transmission */
	__IO uint32_t tmpreg = heth->Instance->DMAOMR & ~( ETH_DMAOMR_ST );

	prvWriteDMAOMR( heth, tmpreg );
}

/**
  * @brief  Enables the DMA reception.
  * @param  heth: pointer to a ETH_HandleTypeDef structure that contains
  *         the configuration information for ETHERNET module
  * @retval None
  */
static void ETH_DMAReceptionEnable(ETH_HandleTypeDef *heth)
{
	/* Enable the DMA reception */
	__IO uint32_t tmpreg = heth->Instance->DMAOMR | ETH_DMAOMR_SR;

	prvWriteDMAOMR( heth, tmpreg );
}

/**
  * @brief  Disables the DMA reception.
  * @param  heth: pointer to a ETH_HandleTypeDef structure that contains
  *         the configuration information for ETHERNET module
  * @retval None
  */
static void ETH_DMAReceptionDisable(ETH_HandleTypeDef *heth)
{
	/* Disable the DMA reception */
	__IO uint32_t tmpreg = heth->Instance->DMAOMR & ~( ETH_DMAOMR_SR );

	prvWriteDMAOMR( heth, tmpreg );
}

/**
  * @brief  Clears the ETHERNET transmit FIFO.
  * @param  heth: pointer to a ETH_HandleTypeDef structure that contains
  *         the configuration information for ETHERNET module
  * @retval None
  */
static void ETH_FlushTransmitFIFO(ETH_HandleTypeDef *heth)
{
	/* Set the Flush Transmit FIFO bit */
	__IO uint32_t tmpreg = heth->Instance->DMAOMR | ETH_DMAOMR_FTF;

	prvWriteDMAOMR( heth, tmpreg );
}

/**
  * @}
  */

#endif /* STM32F7xx */
#endif /* HAL_ETH_MODULE_ENABLED */
/**
  * @}
  */

/**
  * @}
  */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/