FreeRTOS-Plus/Source/FreeRTOS-Plus-Trace/config/trcConfig.h - third_party/github/FreeRTOS/FreeRTOS-Kernel - Git at Google

 /*******************************************************************************
  * Trace Recorder Library for Tracealyzer v4.1.4
  * Percepio AB, www.percepio.com
  *
  * trcConfig.h
  *
  * Main configuration parameters for the trace recorder library.
  * More settings can be found in trcStreamingConfig.h and trcSnapshotConfig.h.
  *
  * Read more at http://percepio.com/2016/10/05/rtos-tracing/
  *
  * Terms of Use
  * This file is part of the trace recorder library (RECORDER), which is the
  * intellectual property of Percepio AB (PERCEPIO) and provided under a
  * license as follows.
  * The RECORDER may be used free of charge for the purpose of recording data
  * intended for analysis in PERCEPIO products. It may not be used or modified
  * for other purposes without explicit permission from PERCEPIO.
  * You may distribute the RECORDER in its original source code form, assuming
  * this text (terms of use, disclaimer, copyright notice) is unchanged. You are
  * allowed to distribute the RECORDER with minor modifications intended for
  * configuration or porting of the RECORDER, e.g., to allow using it on a
  * specific processor, processor family or with a specific communication
  * interface. Any such modifications should be documented directly below
  * this comment block.
  *
  * Disclaimer
  * The RECORDER is being delivered to you AS IS and PERCEPIO makes no warranty
  * as to its use or performance. PERCEPIO does not and cannot warrant the
  * performance or results you may obtain by using the RECORDER or documentation.
  * PERCEPIO make no warranties, express or implied, as to noninfringement of
  * third party rights, merchantability, or fitness for any particular purpose.
  * In no event will PERCEPIO, its technology partners, or distributors be liable
  * to you for any consequential, incidental or special damages, including any
  * lost profits or lost savings, even if a representative of PERCEPIO has been
  * advised of the possibility of such damages, or for any claim by any third
  * party. Some jurisdictions do not allow the exclusion or limitation of
  * incidental, consequential or special damages, or the exclusion of implied
  * warranties or limitations on how long an implied warranty may last, so the
  * above limitations may not apply to you.
  *
  * Tabs are used for indent in this file (1 tab = 4 spaces)
  *
  * Copyright Percepio AB, 2018.
  * www.percepio.com
  ******************************************************************************/

 #ifndef TRC_CONFIG_H
 #define TRC_CONFIG_H

 #ifdef __cplusplus
 extern "C" {
 #endif

 #include "trcPortDefines.h"

 /******************************************************************************
  * Include of processor header file
  *
  * Here you may need to include the header file for your processor. This is
  * required at least for the ARM Cortex-M port, that uses the ARM CMSIS API.
  * Try that in case of build problems. Otherwise, remove the #error line below.
  *****************************************************************************/
 #error "Trace Recorder: Please include your processor's header file here and remove this line."

 /*******************************************************************************
  * Configuration Macro: TRC_CFG_HARDWARE_PORT
  *
  * Specify what hardware port to use (i.e., the "timestamping driver").
  *
  * All ARM Cortex-M MCUs are supported by "TRC_HARDWARE_PORT_ARM_Cortex_M".
  * This port uses the DWT cycle counter for Cortex-M3/M4/M7 devices, which is
  * available on most such devices. In case your device don't have DWT support,
  * you will get an error message opening the trace. In that case, you may
  * force the recorder to use SysTick timestamping instead, using this define:
  *
  * #define TRC_CFG_ARM_CM_USE_SYSTICK
  *
  * For ARM Cortex-M0/M0+ devices, SysTick mode is used automatically.
  *
  * See trcHardwarePort.h for available ports and information on how to
  * define your own port, if not already present.
  ******************************************************************************/
 #define TRC_CFG_HARDWARE_PORT TRC_HARDWARE_PORT_NOT_SET

 /*******************************************************************************
  * Configuration Macro: TRC_CFG_RECORDER_MODE
  *
  * Specify what recording mode to use. Snapshot means that the data is saved in
  * an internal RAM buffer, for later upload. Streaming means that the data is
  * transferred continuously to the host PC.
  *
  * For more information, see http://percepio.com/2016/10/05/rtos-tracing/
  * and the Tracealyzer User Manual.
  *
  * Values:
  * TRC_RECORDER_MODE_SNAPSHOT
  * TRC_RECORDER_MODE_STREAMING
  ******************************************************************************/
 #define TRC_CFG_RECORDER_MODE TRC_RECORDER_MODE_SNAPSHOT

 /******************************************************************************
  * TRC_CFG_FREERTOS_VERSION
  *
  * Specify what version of FreeRTOS that is used (don't change unless using the
  * trace recorder library with an older version of FreeRTOS).
  *
  * TRC_FREERTOS_VERSION_7_3						If using FreeRTOS v7.3.x
  * TRC_FREERTOS_VERSION_7_4						If using FreeRTOS v7.4.x
  * TRC_FREERTOS_VERSION_7_5_OR_7_6				If using FreeRTOS v7.5.0 - v7.6.0
  * TRC_FREERTOS_VERSION_8_X						If using FreeRTOS v8.X.X
  * TRC_FREERTOS_VERSION_9_0_0					If using FreeRTOS v9.0.0
  * TRC_FREERTOS_VERSION_9_0_1					If using FreeRTOS v9.0.1
  * TRC_FREERTOS_VERSION_9_0_2					If using FreeRTOS v9.0.2
  * TRC_FREERTOS_VERSION_10_0_0					If using FreeRTOS v10.0.0 or later
  *****************************************************************************/
 #define TRC_CFG_FREERTOS_VERSION TRC_FREERTOS_VERSION_10_0_0

 /*******************************************************************************
  * TRC_CFG_SCHEDULING_ONLY
  *
  * Macro which should be defined as an integer value.
  *
  * If this setting is enabled (= 1), only scheduling events are recorded.
  * If disabled (= 0), all events are recorded (unless filtered in other ways).
  *
  * Default value is 0 (= include additional events).
  ******************************************************************************/
 #define TRC_CFG_SCHEDULING_ONLY 0

  /******************************************************************************
  * TRC_CFG_INCLUDE_MEMMANG_EVENTS
  *
  * Macro which should be defined as either zero (0) or one (1).
  *
  * This controls if malloc and free calls should be traced. Set this to zero (0)
  * to exclude malloc/free calls, or one (1) to include such events in the trace.
  *
  * Default value is 1.
  *****************************************************************************/
 #define TRC_CFG_INCLUDE_MEMMANG_EVENTS 1

  /******************************************************************************
  * TRC_CFG_INCLUDE_USER_EVENTS
  *
  * Macro which should be defined as either zero (0) or one (1).
  *
  * If this is zero (0), all code related to User Events is excluded in order
  * to reduce code size. Any attempts of storing User Events are then silently
  * ignored.
  *
  * User Events are application-generated events, like "printf" but for the
  * trace log, generated using vTracePrint and vTracePrintF.
  * The formatting is done on host-side, by Tracealyzer. User Events are
  * therefore much faster than a console printf and can often be used
  * in timing critical code without problems.
  *
  * Note: In streaming mode, User Events are used to provide error messages
  * and warnings from the recorder (in case of incorrect configuration) for
  * display in Tracealyzer. Disabling user events will also disable these
  * warnings. You can however still catch them by calling xTraceGetLastError
  * or by putting breakpoints in prvTraceError and prvTraceWarning.
  *
  * Default value is 1.
  *****************************************************************************/
 #define TRC_CFG_INCLUDE_USER_EVENTS 1

  /*****************************************************************************
  * TRC_CFG_INCLUDE_ISR_TRACING
  *
  * Macro which should be defined as either zero (0) or one (1).
  *
  * If this is zero (0), the code for recording Interrupt Service Routines is
  * excluded, in order to reduce code size.
  *
  * Default value is 1.
  *
  * Note: tracing ISRs requires that you insert calls to vTraceStoreISRBegin
  * and vTraceStoreISREnd in your interrupt handlers.
  *****************************************************************************/
 #define TRC_CFG_INCLUDE_ISR_TRACING 1

  /*****************************************************************************
  * TRC_CFG_INCLUDE_READY_EVENTS
  *
  * Macro which should be defined as either zero (0) or one (1).
  *
  * If one (1), events are recorded when tasks enter scheduling state "ready".
  * This allows Tracealyzer to show the initial pending time before tasks enter
  * the execution state, and present accurate response times.
  * If zero (0), "ready events" are not created, which allows for recording
  * longer traces in the same amount of RAM.
  *
  * Default value is 1.
  *****************************************************************************/
 #define TRC_CFG_INCLUDE_READY_EVENTS 1

  /*****************************************************************************
  * TRC_CFG_INCLUDE_OSTICK_EVENTS
  *
  * Macro which should be defined as either zero (0) or one (1).
  *
  * If this is one (1), events will be generated whenever the OS clock is
  * increased. If zero (0), OS tick events are not generated, which allows for
  * recording longer traces in the same amount of RAM.
  *
  * Default value is 1.
  *****************************************************************************/
 #define TRC_CFG_INCLUDE_OSTICK_EVENTS 1

  /*****************************************************************************
  * TRC_CFG_INCLUDE_EVENT_GROUP_EVENTS
  *
  * Macro which should be defined as either zero (0) or one (1).
  *
  * If this is zero (0), the trace will exclude any "event group" events.
  *
  * Default value is 0 (excluded) since dependent on event_groups.c
  *****************************************************************************/
 #define TRC_CFG_INCLUDE_EVENT_GROUP_EVENTS 0

  /*****************************************************************************
  * TRC_CFG_INCLUDE_TIMER_EVENTS
  *
  * Macro which should be defined as either zero (0) or one (1).
  *
  * If this is zero (0), the trace will exclude any Timer events.
  *
  * Default value is 0 since dependent on timers.c
  *****************************************************************************/
 #define TRC_CFG_INCLUDE_TIMER_EVENTS 0

  /*****************************************************************************
  * TRC_CFG_INCLUDE_PEND_FUNC_CALL_EVENTS
  *
  * Macro which should be defined as either zero (0) or one (1).
  *
  * If this is zero (0), the trace will exclude any "pending function call"
  * events, such as xTimerPendFunctionCall().
  *
  * Default value is 0 since dependent on timers.c
  *****************************************************************************/
 #define TRC_CFG_INCLUDE_PEND_FUNC_CALL_EVENTS 0

 /*******************************************************************************
  * Configuration Macro: TRC_CFG_INCLUDE_STREAM_BUFFER_EVENTS
  *
  * Macro which should be defined as either zero (0) or one (1).
  *
  * If this is zero (0), the trace will exclude any stream buffer or message
  * buffer events.
  *
  * Default value is 0 since dependent on stream_buffer.c (new in FreeRTOS v10)
  ******************************************************************************/
 #define TRC_CFG_INCLUDE_STREAM_BUFFER_EVENTS 0

 /*******************************************************************************
  * Configuration Macro: TRC_CFG_RECORDER_BUFFER_ALLOCATION
  *
  * Specifies how the recorder buffer is allocated (also in case of streaming, in
  * port using the recorder's internal temporary buffer)
  *
  * Values:
  * TRC_RECORDER_BUFFER_ALLOCATION_STATIC  - Static allocation (internal)
  * TRC_RECORDER_BUFFER_ALLOCATION_DYNAMIC - Malloc in vTraceEnable
  * TRC_RECORDER_BUFFER_ALLOCATION_CUSTOM  - Use vTraceSetRecorderDataBuffer
  *
  * Static and dynamic mode does the allocation for you, either in compile time
  * (static) or in runtime (malloc).
  * The custom mode allows you to control how and where the allocation is made,
  * for details see TRC_ALLOC_CUSTOM_BUFFER and vTraceSetRecorderDataBuffer().
  ******************************************************************************/
 #define TRC_CFG_RECORDER_BUFFER_ALLOCATION TRC_RECORDER_BUFFER_ALLOCATION_STATIC

 /******************************************************************************
  * TRC_CFG_MAX_ISR_NESTING
  *
  * Defines how many levels of interrupt nesting the recorder can handle, in
  * case multiple ISRs are traced and ISR nesting is possible. If this
  * is exceeded, the particular ISR will not be traced and the recorder then
  * logs an error message. This setting is used to allocate an internal stack
  * for keeping track of the previous execution context (4 byte per entry).
  *
  * This value must be a non-zero positive constant, at least 1.
  *
  * Default value: 8
  *****************************************************************************/
 #define TRC_CFG_MAX_ISR_NESTING 8

 /* Specific configuration, depending on Streaming/Snapshot mode */
 #if (TRC_CFG_RECORDER_MODE == TRC_RECORDER_MODE_SNAPSHOT)
 #include "trcSnapshotConfig.h"
 #elif (TRC_CFG_RECORDER_MODE == TRC_RECORDER_MODE_STREAMING)
 #include "trcStreamingConfig.h"
 #endif

 #ifdef __cplusplus
 }
 #endif

 #endif /* _TRC_CONFIG_H */
	/*******************************************************************************
	* Trace Recorder Library for Tracealyzer v4.1.4
	* Percepio AB, www.percepio.com
	*
	* trcConfig.h
	*
	* Main configuration parameters for the trace recorder library.
	* More settings can be found in trcStreamingConfig.h and trcSnapshotConfig.h.
	*
	* Read more at http://percepio.com/2016/10/05/rtos-tracing/
	*
	* Terms of Use
	* This file is part of the trace recorder library (RECORDER), which is the
	* intellectual property of Percepio AB (PERCEPIO) and provided under a
	* license as follows.
	* The RECORDER may be used free of charge for the purpose of recording data
	* intended for analysis in PERCEPIO products. It may not be used or modified
	* for other purposes without explicit permission from PERCEPIO.
	* You may distribute the RECORDER in its original source code form, assuming
	* this text (terms of use, disclaimer, copyright notice) is unchanged. You are
	* allowed to distribute the RECORDER with minor modifications intended for
	* configuration or porting of the RECORDER, e.g., to allow using it on a
	* specific processor, processor family or with a specific communication
	* interface. Any such modifications should be documented directly below
	* this comment block.
	*
	* Disclaimer
	* The RECORDER is being delivered to you AS IS and PERCEPIO makes no warranty
	* as to its use or performance. PERCEPIO does not and cannot warrant the
	* performance or results you may obtain by using the RECORDER or documentation.
	* PERCEPIO make no warranties, express or implied, as to noninfringement of
	* third party rights, merchantability, or fitness for any particular purpose.
	* In no event will PERCEPIO, its technology partners, or distributors be liable
	* to you for any consequential, incidental or special damages, including any
	* lost profits or lost savings, even if a representative of PERCEPIO has been
	* advised of the possibility of such damages, or for any claim by any third
	* party. Some jurisdictions do not allow the exclusion or limitation of
	* incidental, consequential or special damages, or the exclusion of implied
	* warranties or limitations on how long an implied warranty may last, so the
	* above limitations may not apply to you.
	*
	* Tabs are used for indent in this file (1 tab = 4 spaces)
	*
	* Copyright Percepio AB, 2018.
	* www.percepio.com
	******************************************************************************/

	#ifndef TRC_CONFIG_H
	#define TRC_CONFIG_H

	#ifdef __cplusplus
	extern "C" {
	#endif

	#include "trcPortDefines.h"

	/******************************************************************************
	* Include of processor header file
	*
	* Here you may need to include the header file for your processor. This is
	* required at least for the ARM Cortex-M port, that uses the ARM CMSIS API.
	* Try that in case of build problems. Otherwise, remove the #error line below.
	*****************************************************************************/
	#error "Trace Recorder: Please include your processor's header file here and remove this line."

	/*******************************************************************************
	* Configuration Macro: TRC_CFG_HARDWARE_PORT
	*
	* Specify what hardware port to use (i.e., the "timestamping driver").
	*
	* All ARM Cortex-M MCUs are supported by "TRC_HARDWARE_PORT_ARM_Cortex_M".
	* This port uses the DWT cycle counter for Cortex-M3/M4/M7 devices, which is
	* available on most such devices. In case your device don't have DWT support,
	* you will get an error message opening the trace. In that case, you may
	* force the recorder to use SysTick timestamping instead, using this define:
	*
	* #define TRC_CFG_ARM_CM_USE_SYSTICK
	*
	* For ARM Cortex-M0/M0+ devices, SysTick mode is used automatically.
	*
	* See trcHardwarePort.h for available ports and information on how to
	* define your own port, if not already present.
	******************************************************************************/
	#define TRC_CFG_HARDWARE_PORT TRC_HARDWARE_PORT_NOT_SET

	/*******************************************************************************
	* Configuration Macro: TRC_CFG_RECORDER_MODE
	*
	* Specify what recording mode to use. Snapshot means that the data is saved in
	* an internal RAM buffer, for later upload. Streaming means that the data is
	* transferred continuously to the host PC.
	*
	* For more information, see http://percepio.com/2016/10/05/rtos-tracing/
	* and the Tracealyzer User Manual.
	*
	* Values:
	* TRC_RECORDER_MODE_SNAPSHOT
	* TRC_RECORDER_MODE_STREAMING
	******************************************************************************/
	#define TRC_CFG_RECORDER_MODE TRC_RECORDER_MODE_SNAPSHOT

	/******************************************************************************
	* TRC_CFG_FREERTOS_VERSION
	*
	* Specify what version of FreeRTOS that is used (don't change unless using the
	* trace recorder library with an older version of FreeRTOS).
	*
	* TRC_FREERTOS_VERSION_7_3 If using FreeRTOS v7.3.x
	* TRC_FREERTOS_VERSION_7_4 If using FreeRTOS v7.4.x
	* TRC_FREERTOS_VERSION_7_5_OR_7_6 If using FreeRTOS v7.5.0 - v7.6.0
	* TRC_FREERTOS_VERSION_8_X If using FreeRTOS v8.X.X
	* TRC_FREERTOS_VERSION_9_0_0 If using FreeRTOS v9.0.0
	* TRC_FREERTOS_VERSION_9_0_1 If using FreeRTOS v9.0.1
	* TRC_FREERTOS_VERSION_9_0_2 If using FreeRTOS v9.0.2
	* TRC_FREERTOS_VERSION_10_0_0 If using FreeRTOS v10.0.0 or later
	*****************************************************************************/
	#define TRC_CFG_FREERTOS_VERSION TRC_FREERTOS_VERSION_10_0_0

	/*******************************************************************************
	* TRC_CFG_SCHEDULING_ONLY
	*
	* Macro which should be defined as an integer value.
	*
	* If this setting is enabled (= 1), only scheduling events are recorded.
	* If disabled (= 0), all events are recorded (unless filtered in other ways).
	*
	* Default value is 0 (= include additional events).
	******************************************************************************/
	#define TRC_CFG_SCHEDULING_ONLY 0

	/******************************************************************************
	* TRC_CFG_INCLUDE_MEMMANG_EVENTS
	*
	* Macro which should be defined as either zero (0) or one (1).
	*
	* This controls if malloc and free calls should be traced. Set this to zero (0)
	* to exclude malloc/free calls, or one (1) to include such events in the trace.
	*
	* Default value is 1.
	*****************************************************************************/
	#define TRC_CFG_INCLUDE_MEMMANG_EVENTS 1

	/******************************************************************************
	* TRC_CFG_INCLUDE_USER_EVENTS
	*
	* Macro which should be defined as either zero (0) or one (1).
	*
	* If this is zero (0), all code related to User Events is excluded in order
	* to reduce code size. Any attempts of storing User Events are then silently
	* ignored.
	*
	* User Events are application-generated events, like "printf" but for the
	* trace log, generated using vTracePrint and vTracePrintF.
	* The formatting is done on host-side, by Tracealyzer. User Events are
	* therefore much faster than a console printf and can often be used
	* in timing critical code without problems.
	*
	* Note: In streaming mode, User Events are used to provide error messages
	* and warnings from the recorder (in case of incorrect configuration) for
	* display in Tracealyzer. Disabling user events will also disable these
	* warnings. You can however still catch them by calling xTraceGetLastError
	* or by putting breakpoints in prvTraceError and prvTraceWarning.
	*
	* Default value is 1.
	*****************************************************************************/
	#define TRC_CFG_INCLUDE_USER_EVENTS 1

	/*****************************************************************************
	* TRC_CFG_INCLUDE_ISR_TRACING
	*
	* Macro which should be defined as either zero (0) or one (1).
	*
	* If this is zero (0), the code for recording Interrupt Service Routines is
	* excluded, in order to reduce code size.
	*
	* Default value is 1.
	*
	* Note: tracing ISRs requires that you insert calls to vTraceStoreISRBegin
	* and vTraceStoreISREnd in your interrupt handlers.
	*****************************************************************************/
	#define TRC_CFG_INCLUDE_ISR_TRACING 1

	/*****************************************************************************
	* TRC_CFG_INCLUDE_READY_EVENTS
	*
	* Macro which should be defined as either zero (0) or one (1).
	*
	* If one (1), events are recorded when tasks enter scheduling state "ready".
	* This allows Tracealyzer to show the initial pending time before tasks enter
	* the execution state, and present accurate response times.
	* If zero (0), "ready events" are not created, which allows for recording
	* longer traces in the same amount of RAM.
	*
	* Default value is 1.
	*****************************************************************************/
	#define TRC_CFG_INCLUDE_READY_EVENTS 1

	/*****************************************************************************
	* TRC_CFG_INCLUDE_OSTICK_EVENTS
	*
	* Macro which should be defined as either zero (0) or one (1).
	*
	* If this is one (1), events will be generated whenever the OS clock is
	* increased. If zero (0), OS tick events are not generated, which allows for
	* recording longer traces in the same amount of RAM.
	*
	* Default value is 1.
	*****************************************************************************/
	#define TRC_CFG_INCLUDE_OSTICK_EVENTS 1

	/*****************************************************************************
	* TRC_CFG_INCLUDE_EVENT_GROUP_EVENTS
	*
	* Macro which should be defined as either zero (0) or one (1).
	*
	* If this is zero (0), the trace will exclude any "event group" events.
	*
	* Default value is 0 (excluded) since dependent on event_groups.c
	*****************************************************************************/
	#define TRC_CFG_INCLUDE_EVENT_GROUP_EVENTS 0

	/*****************************************************************************
	* TRC_CFG_INCLUDE_TIMER_EVENTS
	*
	* Macro which should be defined as either zero (0) or one (1).
	*
	* If this is zero (0), the trace will exclude any Timer events.
	*
	* Default value is 0 since dependent on timers.c
	*****************************************************************************/
	#define TRC_CFG_INCLUDE_TIMER_EVENTS 0

	/*****************************************************************************
	* TRC_CFG_INCLUDE_PEND_FUNC_CALL_EVENTS
	*
	* Macro which should be defined as either zero (0) or one (1).
	*
	* If this is zero (0), the trace will exclude any "pending function call"
	* events, such as xTimerPendFunctionCall().
	*
	* Default value is 0 since dependent on timers.c
	*****************************************************************************/
	#define TRC_CFG_INCLUDE_PEND_FUNC_CALL_EVENTS 0

	/*******************************************************************************
	* Configuration Macro: TRC_CFG_INCLUDE_STREAM_BUFFER_EVENTS
	*
	* Macro which should be defined as either zero (0) or one (1).
	*
	* If this is zero (0), the trace will exclude any stream buffer or message
	* buffer events.
	*
	* Default value is 0 since dependent on stream_buffer.c (new in FreeRTOS v10)
	******************************************************************************/
	#define TRC_CFG_INCLUDE_STREAM_BUFFER_EVENTS 0

	/*******************************************************************************
	* Configuration Macro: TRC_CFG_RECORDER_BUFFER_ALLOCATION
	*
	* Specifies how the recorder buffer is allocated (also in case of streaming, in
	* port using the recorder's internal temporary buffer)
	*
	* Values:
	* TRC_RECORDER_BUFFER_ALLOCATION_STATIC - Static allocation (internal)
	* TRC_RECORDER_BUFFER_ALLOCATION_DYNAMIC - Malloc in vTraceEnable
	* TRC_RECORDER_BUFFER_ALLOCATION_CUSTOM - Use vTraceSetRecorderDataBuffer
	*
	* Static and dynamic mode does the allocation for you, either in compile time
	* (static) or in runtime (malloc).
	* The custom mode allows you to control how and where the allocation is made,
	* for details see TRC_ALLOC_CUSTOM_BUFFER and vTraceSetRecorderDataBuffer().
	******************************************************************************/
	#define TRC_CFG_RECORDER_BUFFER_ALLOCATION TRC_RECORDER_BUFFER_ALLOCATION_STATIC

	/******************************************************************************
	* TRC_CFG_MAX_ISR_NESTING
	*
	* Defines how many levels of interrupt nesting the recorder can handle, in
	* case multiple ISRs are traced and ISR nesting is possible. If this
	* is exceeded, the particular ISR will not be traced and the recorder then
	* logs an error message. This setting is used to allocate an internal stack
	* for keeping track of the previous execution context (4 byte per entry).
	*
	* This value must be a non-zero positive constant, at least 1.
	*
	* Default value: 8
	*****************************************************************************/
	#define TRC_CFG_MAX_ISR_NESTING 8

	/* Specific configuration, depending on Streaming/Snapshot mode */
	#if (TRC_CFG_RECORDER_MODE == TRC_RECORDER_MODE_SNAPSHOT)
	#include "trcSnapshotConfig.h"
	#elif (TRC_CFG_RECORDER_MODE == TRC_RECORDER_MODE_STREAMING)
	#include "trcStreamingConfig.h"
	#endif

	#ifdef __cplusplus
	}
	#endif

	#endif /* _TRC_CONFIG_H */