Google Git
Sign in
pigweed / third_party / github / STMicroelectronics / stm32l0xx_hal_driver / 433eef248f43fa27e92ea6abd422c5f5e0f127b4 / . / Src / stm32l0xx_hal_adc.c
blob: 9b3a161d7fb04ff28118dce717c238ae905e6f34 [file] [log] [blame]
/**
******************************************************************************
* @file stm32l0xx_hal_adc.c
* @author MCD Application Team
* @brief This file provides firmware functions to manage the following
* functionalities of the Analog to Digital Convertor (ADC)
* peripheral:
* + Initialization and de-initialization functions
* ++ Initialization and Configuration of ADC
* + Operation functions
* ++ Start, stop, get result of conversions of regular
* group, using 3 possible modes: polling, interruption or DMA.
* + Control functions
* ++ Channels configuration on regular group
* ++ Analog Watchdog configuration
* + State functions
* ++ ADC state machine management
* ++ Interrupts and flags management
* Other functions (extended functions) are available in file
* "stm32l0xx_hal_adc_ex.c".
*
@verbatim
==============================================================================
##### ADC peripheral features #####
==============================================================================
[..]
(+) 12-bit, 10-bit, 8-bit or 6-bit configurable resolution.
(+) Interrupt generation at the end of regular conversion and in case of
analog watchdog or overrun events.
(+) Single and continuous conversion modes.
(+) Scan mode for conversion of several channels sequentially.
(+) Data alignment with in-built data coherency.
(+) Programmable sampling time (common for all channels)
(+) External trigger (timer or EXTI) with configurable polarity
(+) DMA request generation for transfer of conversions data of regular group.
(+) ADC calibration
(+) ADC conversion of regular group.
(+) ADC supply requirements: 1.62 V to 3.6 V.
(+) ADC input range: from Vref- (connected to Vssa) to Vref+ (connected to
Vdda or to an external voltage reference).
##### How to use this driver #####
==============================================================================
[..]
*** Configuration of top level parameters related to ADC ***
============================================================
[..]
(#) Enable the ADC interface
(++) As prerequisite, ADC clock must be configured at RCC top level.
Caution: On STM32L0, ADC clock frequency max is 16MHz (refer
to device datasheet).
Therefore, ADC clock prescaler must be configured in
function of ADC clock source frequency to remain below
this maximum frequency.
(++) Two clock settings are mandatory:
(+++) ADC clock (core clock, also possibly conversion clock).
(+++) ADC clock (conversions clock).
Two possible clock sources: synchronous clock derived from APB clock
or asynchronous clock derived from ADC dedicated HSI RC oscillator
16MHz.
If asynchronous clock is selected, parameter "HSIState" must be set either:
- to "...HSIState = RCC_HSI_ON" to maintain the HSI16 oscillator
always enabled: can be used to supply the main system clock.
(+++) Example:
Into HAL_ADC_MspInit() (recommended code location) or with
other device clock parameters configuration:
(+++) __HAL_RCC_ADC1_CLK_ENABLE(); (mandatory)
HSI enable (optional: if asynchronous clock selected)
(+++) RCC_OscInitTypeDef RCC_OscInitStructure;
(+++) RCC_OscInitStructure.OscillatorType = RCC_OSCILLATORTYPE_HSI;
(+++) RCC_OscInitStructure.HSI16CalibrationValue = RCC_HSICALIBRATION_DEFAULT;
(+++) RCC_OscInitStructure.HSIState = RCC_HSI_ON;
(+++) RCC_OscInitStructure.PLL... (optional if used for system clock)
(+++) HAL_RCC_OscConfig(&RCC_OscInitStructure);
(++) ADC clock source and clock prescaler are configured at ADC level with
parameter "ClockPrescaler" using function HAL_ADC_Init().
(#) ADC pins configuration
(++) Enable the clock for the ADC GPIOs
using macro __HAL_RCC_GPIOx_CLK_ENABLE()
(++) Configure these ADC pins in analog mode
using function HAL_GPIO_Init()
(#) Optionally, in case of usage of ADC with interruptions:
(++) Configure the NVIC for ADC
using function HAL_NVIC_EnableIRQ(ADCx_IRQn)
(++) Insert the ADC interruption handler function HAL_ADC_IRQHandler()
into the function of corresponding ADC interruption vector
ADCx_IRQHandler().
(#) Optionally, in case of usage of DMA:
(++) Configure the DMA (DMA channel, mode normal or circular, ...)
using function HAL_DMA_Init().
(++) Configure the NVIC for DMA
using function HAL_NVIC_EnableIRQ(DMAx_Channelx_IRQn)
(++) Insert the ADC interruption handler function HAL_ADC_IRQHandler()
into the function of corresponding DMA interruption vector
DMAx_Channelx_IRQHandler().
*** Configuration of ADC, group regular, channels parameters ***
================================================================
[..]
(#) Configure the ADC parameters (resolution, data alignment, ...)
and regular group parameters (conversion trigger, sequencer, ...)
using function HAL_ADC_Init().
(#) Configure the channels for regular group parameters (channel number,
channel rank into sequencer, ..., into regular group)
using function HAL_ADC_ConfigChannel().
(#) Optionally, configure the analog watchdog parameters (channels
monitored, thresholds, ...)
using function HAL_ADC_AnalogWDGConfig().
(#) When device is in mode low-power (low-power run, low-power sleep or stop mode),
function "HAL_ADCEx_EnableVREFINT()" must be called before function HAL_ADC_Init().
In case of internal temperature sensor to be measured:
function "HAL_ADCEx_EnableVREFINTTempSensor()" must be called similarilly
*** Execution of ADC conversions ***
====================================
[..]
(#) Optionally, perform an automatic ADC calibration to improve the
conversion accuracy
using function HAL_ADCEx_Calibration_Start().
(#) ADC driver can be used among three modes: polling, interruption,
transfer by DMA.
(++) ADC conversion by polling:
(+++) Activate the ADC peripheral and start conversions
using function HAL_ADC_Start()
(+++) Wait for ADC conversion completion
using function HAL_ADC_PollForConversion()
(+++) Retrieve conversion results
using function HAL_ADC_GetValue()
(+++) Stop conversion and disable the ADC peripheral
using function HAL_ADC_Stop()
(++) ADC conversion by interruption:
(+++) Activate the ADC peripheral and start conversions
using function HAL_ADC_Start_IT()
(+++) Wait for ADC conversion completion by call of function
HAL_ADC_ConvCpltCallback()
(this function must be implemented in user program)
(+++) Retrieve conversion results
using function HAL_ADC_GetValue()
(+++) Stop conversion and disable the ADC peripheral
using function HAL_ADC_Stop_IT()
(++) ADC conversion with transfer by DMA:
(+++) Activate the ADC peripheral and start conversions
using function HAL_ADC_Start_DMA()
(+++) Wait for ADC conversion completion by call of function
HAL_ADC_ConvCpltCallback() or HAL_ADC_ConvHalfCpltCallback()
(these functions must be implemented in user program)
(+++) Conversion results are automatically transferred by DMA into
destination variable address.
(+++) Stop conversion and disable the ADC peripheral
using function HAL_ADC_Stop_DMA()
[..]
(@) Callback functions must be implemented in user program:
(+@) HAL_ADC_ErrorCallback()
(+@) HAL_ADC_LevelOutOfWindowCallback() (callback of analog watchdog)
(+@) HAL_ADC_ConvCpltCallback()
(+@) HAL_ADC_ConvHalfCpltCallback
*** Deinitialization of ADC ***
============================================================
[..]
(#) Disable the ADC interface
(++) ADC clock can be hard reset and disabled at RCC top level.
(++) Hard reset of ADC peripherals
using macro __ADCx_FORCE_RESET(), __ADCx_RELEASE_RESET().
(++) ADC clock disable
using the equivalent macro/functions as configuration step.
(+++) Example:
Into HAL_ADC_MspDeInit() (recommended code location) or with
other device clock parameters configuration:
(+++) RCC_OscInitStructure.OscillatorType = RCC_OSCILLATORTYPE_HSI;
(+++) RCC_OscInitStructure.HSIState = RCC_HSI_OFF; (if not used for system clock)
(+++) HAL_RCC_OscConfig(&RCC_OscInitStructure);
(#) ADC pins configuration
(++) Disable the clock for the ADC GPIOs
using macro __HAL_RCC_GPIOx_CLK_DISABLE()
(#) Optionally, in case of usage of ADC with interruptions:
(++) Disable the NVIC for ADC
using function HAL_NVIC_EnableIRQ(ADCx_IRQn)
(#) Optionally, in case of usage of DMA:
(++) Deinitialize the DMA
using function HAL_DMA_Init().
(++) Disable the NVIC for DMA
using function HAL_NVIC_EnableIRQ(DMAx_Channelx_IRQn)
[..]
*** Callback registration ***
=============================================
[..]
The compilation flag USE_HAL_ADC_REGISTER_CALLBACKS, when set to 1,
allows the user to configure dynamically the driver callbacks.
Use Functions @ref HAL_ADC_RegisterCallback()
to register an interrupt callback.
[..]
Function @ref HAL_ADC_RegisterCallback() allows to register following callbacks:
(+) ConvCpltCallback : ADC conversion complete callback
(+) ConvHalfCpltCallback : ADC conversion DMA half-transfer callback
(+) LevelOutOfWindowCallback : ADC analog watchdog 1 callback
(+) ErrorCallback : ADC error callback
(+) MspInitCallback : ADC Msp Init callback
(+) MspDeInitCallback : ADC Msp DeInit callback
This function takes as parameters the HAL peripheral handle, the Callback ID
and a pointer to the user callback function.
[..]
Use function @ref HAL_ADC_UnRegisterCallback to reset a callback to the default
weak function.
[..]
@ref HAL_ADC_UnRegisterCallback takes as parameters the HAL peripheral handle,
and the Callback ID.
This function allows to reset following callbacks:
(+) ConvCpltCallback : ADC conversion complete callback
(+) ConvHalfCpltCallback : ADC conversion DMA half-transfer callback
(+) LevelOutOfWindowCallback : ADC analog watchdog 1 callback
(+) ErrorCallback : ADC error callback
(+) MspInitCallback : ADC Msp Init callback
(+) MspDeInitCallback : ADC Msp DeInit callback
[..]
By default, after the @ref HAL_ADC_Init() and when the state is @ref HAL_ADC_STATE_RESET
all callbacks are set to the corresponding weak functions:
examples @ref HAL_ADC_ConvCpltCallback(), @ref HAL_ADC_ErrorCallback().
Exception done for MspInit and MspDeInit functions that are
reset to the legacy weak functions in the @ref HAL_ADC_Init()/ @ref HAL_ADC_DeInit() only when
these callbacks are null (not registered beforehand).
[..]
If MspInit or MspDeInit are not null, the @ref HAL_ADC_Init()/ @ref HAL_ADC_DeInit()
keep and use the user MspInit/MspDeInit callbacks (registered beforehand) whatever the state.
[..]
Callbacks can be registered/unregistered in @ref HAL_ADC_STATE_READY state only.
Exception done MspInit/MspDeInit functions that can be registered/unregistered
in @ref HAL_ADC_STATE_READY or @ref HAL_ADC_STATE_RESET state,
thus registered (user) MspInit/DeInit callbacks can be used during the Init/DeInit.
[..]
Then, the user first registers the MspInit/MspDeInit user callbacks
using @ref HAL_ADC_RegisterCallback() before calling @ref HAL_ADC_DeInit()
or @ref HAL_ADC_Init() function.
[..]
When the compilation flag USE_HAL_ADC_REGISTER_CALLBACKS is set to 0 or
not defined, the callback registration feature is not available and all callbacks
are set to the corresponding weak functions.
@endverbatim
******************************************************************************
* @attention
*
* <h2><center>&copy; Copyright(c) 2016 STMicroelectronics.
* All rights reserved.</center></h2>
*
* This software component is licensed by ST under BSD 3-Clause license,
* the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
******************************************************************************
*/
/* Includes ------------------------------------------------------------------*/
#include "stm32l0xx_hal.h"
/** @addtogroup STM32L0xx_HAL_Driver
* @{
*/
/** @defgroup ADC ADC
* @brief ADC HAL module driver
* @{
*/
#ifdef HAL_ADC_MODULE_ENABLED
/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/** @defgroup ADC_Private_Constants ADC Private Constants
* @{
*/
/* Delay for ADC stabilization time. */
/* Maximum delay is 1us (refer to device datasheet, parameter tSTART). */
/* Unit: us */
#define ADC_STAB_DELAY_US (1U)
/* Delay for temperature sensor stabilization time. */
/* Maximum delay is 10us (refer to device datasheet, parameter tSTART). */
/* Unit: us */
#define ADC_TEMPSENSOR_DELAY_US (10U)
/**
* @}
*/
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
/** @defgroup ADC_Private_Functions ADC Private Functions
* @{
*/
static HAL_StatusTypeDef ADC_Enable(ADC_HandleTypeDef* hadc);
static HAL_StatusTypeDef ADC_Disable(ADC_HandleTypeDef* hadc);
static HAL_StatusTypeDef ADC_ConversionStop(ADC_HandleTypeDef* hadc);
static void ADC_DMAConvCplt(DMA_HandleTypeDef *hdma);
static void ADC_DMAHalfConvCplt(DMA_HandleTypeDef *hdma);
static void ADC_DMAError(DMA_HandleTypeDef *hdma);
static void ADC_DelayMicroSecond(uint32_t microSecond);
/**
* @}
*/
/* Exported functions ---------------------------------------------------------*/
/** @defgroup ADC_Exported_Functions ADC Exported Functions
* @{
*/
/** @defgroup ADC_Exported_Functions_Group1 Initialization and de-initialization functions
* @brief ADC Initialization and Configuration functions
*
@verbatim
===============================================================================
##### Initialization and de-initialization functions #####
===============================================================================
[..] This section provides functions allowing to:
(+) Initialize and configure the ADC.
(+) De-initialize the ADC.
@endverbatim
* @{
*/
/**
* @brief Initialize the ADC peripheral and regular group according to
* parameters specified in structure "ADC_InitTypeDef".
* @note As prerequisite, ADC clock must be configured at RCC top level
* depending on possible clock sources: APB clock of HSI clock.
* See commented example code below that can be copied and uncommented
* into HAL_ADC_MspInit().
* @note Possibility to update parameters on the fly:
* This function initializes the ADC MSP (HAL_ADC_MspInit()) only when
* coming from ADC state reset. Following calls to this function can
* be used to reconfigure some parameters of ADC_InitTypeDef
* structure on the fly, without modifying MSP configuration. If ADC
* MSP has to be modified again, HAL_ADC_DeInit() must be called
* before HAL_ADC_Init().
* The setting of these parameters is conditioned to ADC state.
* For parameters constraints, see comments of structure
* "ADC_InitTypeDef".
* @note This function configures the ADC within 2 scopes: scope of entire
* ADC and scope of regular group. For parameters details, see comments
* of structure "ADC_InitTypeDef".
* @note When device is in mode low-power (low-power run, low-power sleep or stop mode),
* function "HAL_ADCEx_EnableVREFINT()" must be called before function HAL_ADC_Init()
* (in case of previous ADC operations: function HAL_ADC_DeInit() must be called first).
* In case of internal temperature sensor to be measured:
* function "HAL_ADCEx_EnableVREFINTTempSensor()" must be called similarilly.
* @param hadc ADC handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_ADC_Init(ADC_HandleTypeDef* hadc)
{
/* Check ADC handle */
if(hadc == NULL)
{
return HAL_ERROR;
}
/* Check the parameters */
assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
assert_param(IS_ADC_CLOCKPRESCALER(hadc->Init.ClockPrescaler));
assert_param(IS_ADC_RESOLUTION(hadc->Init.Resolution));
assert_param(IS_ADC_DATA_ALIGN(hadc->Init.DataAlign));
assert_param(IS_ADC_SCAN_MODE(hadc->Init.ScanConvMode));
assert_param(IS_FUNCTIONAL_STATE(hadc->Init.ContinuousConvMode));
assert_param(IS_FUNCTIONAL_STATE(hadc->Init.DiscontinuousConvMode));
assert_param(IS_ADC_EXTTRIG_EDGE(hadc->Init.ExternalTrigConvEdge));
assert_param(IS_ADC_EXTTRIG(hadc->Init.ExternalTrigConv));
assert_param(IS_FUNCTIONAL_STATE(hadc->Init.DMAContinuousRequests));
assert_param(IS_ADC_EOC_SELECTION(hadc->Init.EOCSelection));
assert_param(IS_ADC_OVERRUN(hadc->Init.Overrun));
assert_param(IS_FUNCTIONAL_STATE(hadc->Init.LowPowerAutoWait));
assert_param(IS_FUNCTIONAL_STATE(hadc->Init.LowPowerFrequencyMode));
assert_param(IS_FUNCTIONAL_STATE(hadc->Init.LowPowerAutoPowerOff));
assert_param(IS_ADC_SAMPLE_TIME(hadc->Init.SamplingTime));
assert_param(IS_FUNCTIONAL_STATE(hadc->Init.OversamplingMode));
/* As prerequisite, into HAL_ADC_MspInit(), ADC clock must be configured */
/* at RCC top level depending on both possible clock sources: */
/* APB clock or HSI clock. */
/* Refer to header of this file for more details on clock enabling procedure*/
/* Actions performed only if ADC is coming from state reset: */
/* - Initialization of ADC MSP */
/* - ADC voltage regulator enable */
if(hadc->State == HAL_ADC_STATE_RESET)
{
/* Initialize ADC error code */
ADC_CLEAR_ERRORCODE(hadc);
/* Allocate lock resource and initialize it */
hadc->Lock = HAL_UNLOCKED;
#if (USE_HAL_ADC_REGISTER_CALLBACKS == 1)
/* Init the ADC Callback settings */
hadc->ConvCpltCallback = HAL_ADC_ConvCpltCallback; /* Legacy weak callback */
hadc->ConvHalfCpltCallback = HAL_ADC_ConvHalfCpltCallback; /* Legacy weak callback */
hadc->LevelOutOfWindowCallback = HAL_ADC_LevelOutOfWindowCallback; /* Legacy weak callback */
hadc->ErrorCallback = HAL_ADC_ErrorCallback; /* Legacy weak callback */
if (hadc->MspInitCallback == NULL)
{
hadc->MspInitCallback = HAL_ADC_MspInit; /* Legacy weak MspInit */
}
/* Init the low level hardware */
hadc->MspInitCallback(hadc);
#else
/* Init the low level hardware */
HAL_ADC_MspInit(hadc);
#endif /* USE_HAL_ADC_REGISTER_CALLBACKS */
}
/* Configuration of ADC parameters if previous preliminary actions are */
/* correctly completed. */
/* and if there is no conversion on going on regular group (ADC can be */
/* enabled anyway, in case of call of this function to update a parameter */
/* on the fly). */
if (HAL_IS_BIT_SET(hadc->State, HAL_ADC_STATE_ERROR_INTERNAL) ||
(ADC_IS_CONVERSION_ONGOING_REGULAR(hadc) != RESET) )
{
/* Update ADC state machine to error */
SET_BIT(hadc->State, HAL_ADC_STATE_ERROR_INTERNAL);
/* Process unlocked */
__HAL_UNLOCK(hadc);
return HAL_ERROR;
}
/* Set ADC state */
ADC_STATE_CLR_SET(hadc->State,
HAL_ADC_STATE_REG_BUSY,
HAL_ADC_STATE_BUSY_INTERNAL);
/* Parameters update conditioned to ADC state: */
/* Parameters that can be updated only when ADC is disabled: */
/* - ADC clock mode */
/* - ADC clock prescaler */
/* - ADC Resolution */
if (ADC_IS_ENABLE(hadc) == RESET)
{
/* Some parameters of this register are not reset, since they are set */
/* by other functions and must be kept in case of usage of this */
/* function on the fly (update of a parameter of ADC_InitTypeDef */
/* without needing to reconfigure all other ADC groups/channels */
/* parameters): */
/* - internal measurement paths: Vbat, temperature sensor, Vref */
/* (set into HAL_ADC_ConfigChannel() ) */
/* Configuration of ADC clock: clock source PCLK or asynchronous with
selectable prescaler */
__HAL_ADC_CLOCK_PRESCALER(hadc);
/* Configuration of ADC: */
/* - Resolution */
hadc->Instance->CFGR1 &= ~( ADC_CFGR1_RES);
hadc->Instance->CFGR1 |= hadc->Init.Resolution;
}
/* Set the Low Frequency mode */
ADC->CCR &= (uint32_t)~ADC_CCR_LFMEN;
ADC->CCR |=__HAL_ADC_CCR_LOWFREQUENCY(hadc->Init.LowPowerFrequencyMode);
/* Enable voltage regulator (if disabled at this step) */
if (HAL_IS_BIT_CLR(hadc->Instance->CR, ADC_CR_ADVREGEN))
{
/* Set ADVREGEN bit */
hadc->Instance->CR |= ADC_CR_ADVREGEN;
}
/* Configuration of ADC: */
/* - Resolution */
/* - Data alignment */
/* - Scan direction */
/* - External trigger to start conversion */
/* - External trigger polarity */
/* - Continuous conversion mode */
/* - DMA continuous request */
/* - Overrun */
/* - AutoDelay feature */
/* - Discontinuous mode */
hadc->Instance->CFGR1 &= ~(ADC_CFGR1_ALIGN |
ADC_CFGR1_SCANDIR |
ADC_CFGR1_EXTSEL |
ADC_CFGR1_EXTEN |
ADC_CFGR1_CONT |
ADC_CFGR1_DMACFG |
ADC_CFGR1_OVRMOD |
ADC_CFGR1_AUTDLY |
ADC_CFGR1_AUTOFF |
ADC_CFGR1_DISCEN );
hadc->Instance->CFGR1 |= (hadc->Init.DataAlign |
ADC_SCANDIR(hadc->Init.ScanConvMode) |
ADC_CONTINUOUS((uint32_t)hadc->Init.ContinuousConvMode) |
ADC_DMACONTREQ((uint32_t)hadc->Init.DMAContinuousRequests) |
hadc->Init.Overrun |
__HAL_ADC_CFGR1_AutoDelay(hadc->Init.LowPowerAutoWait) |
__HAL_ADC_CFGR1_AUTOFF(hadc->Init.LowPowerAutoPowerOff));
/* Enable external trigger if trigger selection is different of software */
/* start. */
/* Note: This configuration keeps the hardware feature of parameter */
/* ExternalTrigConvEdge "trigger edge none" equivalent to */
/* software start. */
if (hadc->Init.ExternalTrigConv != ADC_SOFTWARE_START)
{
hadc->Instance->CFGR1 |= hadc->Init.ExternalTrigConv |
hadc->Init.ExternalTrigConvEdge;
}
/* Enable discontinuous mode only if continuous mode is disabled */
if (hadc->Init.DiscontinuousConvMode == ENABLE)
{
if (hadc->Init.ContinuousConvMode == DISABLE)
{
/* Enable the selected ADC group regular discontinuous mode */
hadc->Instance->CFGR1 |= (ADC_CFGR1_DISCEN);
}
else
{
/* ADC regular group discontinuous was intended to be enabled, */
/* but ADC regular group modes continuous and sequencer discontinuous */
/* cannot be enabled simultaneously. */
/* Update ADC state machine to error */
SET_BIT(hadc->State, HAL_ADC_STATE_ERROR_CONFIG);
/* Set ADC error code to ADC peripheral internal error */
SET_BIT(hadc->ErrorCode, HAL_ADC_ERROR_INTERNAL);
}
}
if (hadc->Init.OversamplingMode == ENABLE)
{
assert_param(IS_ADC_OVERSAMPLING_RATIO(hadc->Init.Oversample.Ratio));
assert_param(IS_ADC_RIGHT_BIT_SHIFT(hadc->Init.Oversample.RightBitShift));
assert_param(IS_ADC_TRIGGERED_OVERSAMPLING_MODE(hadc->Init.Oversample.TriggeredMode));
/* Configuration of Oversampler: */
/* - Oversampling Ratio */
/* - Right bit shift */
/* - Triggered mode */
hadc->Instance->CFGR2 &= ~( ADC_CFGR2_OVSR |
ADC_CFGR2_OVSS |
ADC_CFGR2_TOVS );
hadc->Instance->CFGR2 |= ( hadc->Init.Oversample.Ratio |
hadc->Init.Oversample.RightBitShift |
hadc->Init.Oversample.TriggeredMode );
/* Enable OverSampling mode */
hadc->Instance->CFGR2 |= ADC_CFGR2_OVSE;
}
else
{
if(HAL_IS_BIT_SET(hadc->Instance->CFGR2, ADC_CFGR2_OVSE))
{
/* Disable OverSampling mode if needed */
hadc->Instance->CFGR2 &= ~ADC_CFGR2_OVSE;
}
}
/* Clear the old sampling time */
hadc->Instance->SMPR &= (uint32_t)(~ADC_SMPR_SMPR);
/* Set the new sample time */
hadc->Instance->SMPR |= hadc->Init.SamplingTime;
/* Clear ADC error code */
ADC_CLEAR_ERRORCODE(hadc);
/* Set the ADC state */
ADC_STATE_CLR_SET(hadc->State,
HAL_ADC_STATE_BUSY_INTERNAL,
HAL_ADC_STATE_READY);
/* Return function status */
return HAL_OK;
}
/**
* @brief Deinitialize the ADC peripheral registers to their default reset
* values, with deinitialization of the ADC MSP.
* @note For devices with several ADCs: reset of ADC common registers is done
* only if all ADCs sharing the same common group are disabled.
* If this is not the case, reset of these common parameters reset is
* bypassed without error reporting: it can be the intended behavior in
* case of reset of a single ADC while the other ADCs sharing the same
* common group is still running.
* @param hadc ADC handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_ADC_DeInit(ADC_HandleTypeDef* hadc)
{
HAL_StatusTypeDef tmp_hal_status = HAL_OK;
/* Check ADC handle */
if(hadc == NULL)
{
return HAL_ERROR;
}
/* Check the parameters */
assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
/* Set ADC state */
SET_BIT(hadc->State, HAL_ADC_STATE_BUSY_INTERNAL);
/* Stop potential conversion on going, on regular group */
tmp_hal_status = ADC_ConversionStop(hadc);
/* Disable ADC peripheral if conversions are effectively stopped */
if (tmp_hal_status == HAL_OK)
{
/* Disable the ADC peripheral */
tmp_hal_status = ADC_Disable(hadc);
/* Check if ADC is effectively disabled */
if (tmp_hal_status != HAL_ERROR)
{
/* Change ADC state */
hadc->State = HAL_ADC_STATE_READY;
}
}
/* Configuration of ADC parameters if previous preliminary actions are */
/* correctly completed. */
if (tmp_hal_status != HAL_ERROR)
{
/* ========== Reset ADC registers ========== */
/* Reset register IER */
__HAL_ADC_DISABLE_IT(hadc, (ADC_IT_AWD | ADC_IT_OVR | ADC_IT_EOCAL | ADC_IT_EOS | \
ADC_IT_EOC | ADC_IT_RDY | ADC_IT_EOSMP ));
/* Reset register ISR */
__HAL_ADC_CLEAR_FLAG(hadc, (ADC_FLAG_AWD | ADC_FLAG_EOCAL | ADC_FLAG_OVR | ADC_FLAG_EOS | \
ADC_FLAG_EOC | ADC_FLAG_EOSMP | ADC_FLAG_RDY));
/* Reset register CR */
/* Disable voltage regulator */
/* Note: Regulator disable useful for power saving */
/* Reset ADVREGEN bit */
hadc->Instance->CR &= ~ADC_CR_ADVREGEN;
/* Bits ADC_CR_ADSTP, ADC_CR_ADSTART are in access mode "read-set": no direct reset applicable */
/* No action */
/* Reset register CFGR1 */
hadc->Instance->CFGR1 &= ~(ADC_CFGR1_AWDCH | ADC_CFGR1_AWDEN | ADC_CFGR1_AWDSGL | \
ADC_CFGR1_DISCEN | ADC_CFGR1_AUTOFF | ADC_CFGR1_AUTDLY | \
ADC_CFGR1_CONT | ADC_CFGR1_OVRMOD | ADC_CFGR1_EXTEN | \
ADC_CFGR1_EXTSEL | ADC_CFGR1_ALIGN | ADC_CFGR1_RES | \
ADC_CFGR1_SCANDIR| ADC_CFGR1_DMACFG | ADC_CFGR1_DMAEN);
/* Reset register CFGR2 */
hadc->Instance->CFGR2 &= ~(ADC_CFGR2_TOVS | ADC_CFGR2_OVSS | ADC_CFGR2_OVSR | \
ADC_CFGR2_OVSE | ADC_CFGR2_CKMODE );
/* Reset register SMPR */
hadc->Instance->SMPR &= ~(ADC_SMPR_SMPR);
/* Reset register TR */
hadc->Instance->TR &= ~(ADC_TR_LT | ADC_TR_HT);
/* Reset register CALFACT */
hadc->Instance->CALFACT &= ~(ADC_CALFACT_CALFACT);
/* Reset register DR */
/* bits in access mode read only, no direct reset applicable*/
/* Reset register CALFACT */
hadc->Instance->CALFACT &= ~(ADC_CALFACT_CALFACT);
/* ========== Hard reset ADC peripheral ========== */
/* Performs a global reset of the entire ADC peripheral: ADC state is */
/* forced to a similar state after device power-on. */
/* If needed, copy-paste and uncomment the following reset code into */
/* function "void HAL_ADC_MspInit(ADC_HandleTypeDef* hadc)": */
/* */
/* __HAL_RCC_ADC1_FORCE_RESET() */
/* __HAL_RCC_ADC1_RELEASE_RESET() */
#if (USE_HAL_ADC_REGISTER_CALLBACKS == 1)
if (hadc->MspDeInitCallback == NULL)
{
hadc->MspDeInitCallback = HAL_ADC_MspDeInit; /* Legacy weak MspDeInit */
}
/* DeInit the low level hardware */
hadc->MspDeInitCallback(hadc);
#else
/* DeInit the low level hardware */
HAL_ADC_MspDeInit(hadc);
#endif /* USE_HAL_ADC_REGISTER_CALLBACKS */
/* Set ADC error code to none */
ADC_CLEAR_ERRORCODE(hadc);
/* Set ADC state */
hadc->State = HAL_ADC_STATE_RESET;
}
/* Process unlocked */
__HAL_UNLOCK(hadc);
/* Return function status */
return tmp_hal_status;
}
/**
* @brief Initialize the ADC MSP.
* @param hadc ADC handle
* @retval None
*/
__weak void HAL_ADC_MspInit(ADC_HandleTypeDef* hadc)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hadc);
/* NOTE : This function should not be modified. When the callback is needed,
function HAL_ADC_MspInit must be implemented in the user file.
*/
}
/**
* @brief DeInitialize the ADC MSP.
* @param hadc ADC handle
* @retval None
*/
__weak void HAL_ADC_MspDeInit(ADC_HandleTypeDef* hadc)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hadc);
/* NOTE : This function should not be modified. When the callback is needed,
function HAL_ADC_MspDeInit must be implemented in the user file.
*/
}
#if (USE_HAL_ADC_REGISTER_CALLBACKS == 1)
/**
* @brief Register a User ADC Callback
* To be used instead of the weak predefined callback
* @param hadc Pointer to a ADC_HandleTypeDef structure that contains
* the configuration information for the specified ADC.
* @param CallbackID ID of the callback to be registered
* This parameter can be one of the following values:
* @arg @ref HAL_ADC_CONVERSION_COMPLETE_CB_ID ADC conversion complete callback ID
* @arg @ref HAL_ADC_CONVERSION_HALF_CB_ID ADC conversion complete callback ID
* @arg @ref HAL_ADC_LEVEL_OUT_OF_WINDOW_1_CB_ID ADC analog watchdog 1 callback ID
* @arg @ref HAL_ADC_ERROR_CB_ID ADC error callback ID
* @arg @ref HAL_ADC_INJ_CONVERSION_COMPLETE_CB_ID ADC group injected conversion complete callback ID
* @arg @ref HAL_ADC_MSPINIT_CB_ID ADC Msp Init callback ID
* @arg @ref HAL_ADC_MSPDEINIT_CB_ID ADC Msp DeInit callback ID
* @arg @ref HAL_ADC_MSPINIT_CB_ID MspInit callback ID
* @arg @ref HAL_ADC_MSPDEINIT_CB_ID MspDeInit callback ID
* @param pCallback pointer to the Callback function
* @retval HAL status
*/
HAL_StatusTypeDef HAL_ADC_RegisterCallback(ADC_HandleTypeDef *hadc, HAL_ADC_CallbackIDTypeDef CallbackID, pADC_CallbackTypeDef pCallback)
{
HAL_StatusTypeDef status = HAL_OK;
if (pCallback == NULL)
{
/* Update the error code */
hadc->ErrorCode |= HAL_ADC_ERROR_INVALID_CALLBACK;
return HAL_ERROR;
}
if ((hadc->State & HAL_ADC_STATE_READY) != 0)
{
switch (CallbackID)
{
case HAL_ADC_CONVERSION_COMPLETE_CB_ID :
hadc->ConvCpltCallback = pCallback;
break;
case HAL_ADC_CONVERSION_HALF_CB_ID :
hadc->ConvHalfCpltCallback = pCallback;
break;
case HAL_ADC_LEVEL_OUT_OF_WINDOW_1_CB_ID :
hadc->LevelOutOfWindowCallback = pCallback;
break;
case HAL_ADC_ERROR_CB_ID :
hadc->ErrorCallback = pCallback;
break;
case HAL_ADC_MSPINIT_CB_ID :
hadc->MspInitCallback = pCallback;
break;
case HAL_ADC_MSPDEINIT_CB_ID :
hadc->MspDeInitCallback = pCallback;
break;
default :
/* Update the error code */
hadc->ErrorCode |= HAL_ADC_ERROR_INVALID_CALLBACK;
/* Return error status */
status = HAL_ERROR;
break;
}
}
else if (HAL_ADC_STATE_RESET == hadc->State)
{
switch (CallbackID)
{
case HAL_ADC_MSPINIT_CB_ID :
hadc->MspInitCallback = pCallback;
break;
case HAL_ADC_MSPDEINIT_CB_ID :
hadc->MspDeInitCallback = pCallback;
break;
default :
/* Update the error code */
hadc->ErrorCode |= HAL_ADC_ERROR_INVALID_CALLBACK;
/* Return error status */
status = HAL_ERROR;
break;
}
}
else
{
/* Update the error code */
hadc->ErrorCode |= HAL_ADC_ERROR_INVALID_CALLBACK;
/* Return error status */
status = HAL_ERROR;
}
return status;
}
/**
* @brief Unregister a ADC Callback
* ADC callback is redirected to the weak predefined callback
* @param hadc Pointer to a ADC_HandleTypeDef structure that contains
* the configuration information for the specified ADC.
* @param CallbackID ID of the callback to be unregistered
* This parameter can be one of the following values:
* @arg @ref HAL_ADC_CONVERSION_COMPLETE_CB_ID ADC conversion complete callback ID
* @arg @ref HAL_ADC_CONVERSION_HALF_CB_ID ADC conversion complete callback ID
* @arg @ref HAL_ADC_LEVEL_OUT_OF_WINDOW_1_CB_ID ADC analog watchdog 1 callback ID
* @arg @ref HAL_ADC_ERROR_CB_ID ADC error callback ID
* @arg @ref HAL_ADC_INJ_CONVERSION_COMPLETE_CB_ID ADC group injected conversion complete callback ID
* @arg @ref HAL_ADC_MSPINIT_CB_ID ADC Msp Init callback ID
* @arg @ref HAL_ADC_MSPDEINIT_CB_ID ADC Msp DeInit callback ID
* @arg @ref HAL_ADC_MSPINIT_CB_ID MspInit callback ID
* @arg @ref HAL_ADC_MSPDEINIT_CB_ID MspDeInit callback ID
* @retval HAL status
*/
HAL_StatusTypeDef HAL_ADC_UnRegisterCallback(ADC_HandleTypeDef *hadc, HAL_ADC_CallbackIDTypeDef CallbackID)
{
HAL_StatusTypeDef status = HAL_OK;
if ((hadc->State & HAL_ADC_STATE_READY) != 0)
{
switch (CallbackID)
{
case HAL_ADC_CONVERSION_COMPLETE_CB_ID :
hadc->ConvCpltCallback = HAL_ADC_ConvCpltCallback;
break;
case HAL_ADC_CONVERSION_HALF_CB_ID :
hadc->ConvHalfCpltCallback = HAL_ADC_ConvHalfCpltCallback;
break;
case HAL_ADC_LEVEL_OUT_OF_WINDOW_1_CB_ID :
hadc->LevelOutOfWindowCallback = HAL_ADC_LevelOutOfWindowCallback;
break;
case HAL_ADC_ERROR_CB_ID :
hadc->ErrorCallback = HAL_ADC_ErrorCallback;
break;
case HAL_ADC_MSPINIT_CB_ID :
hadc->MspInitCallback = HAL_ADC_MspInit; /* Legacy weak MspInit */
break;
case HAL_ADC_MSPDEINIT_CB_ID :
hadc->MspDeInitCallback = HAL_ADC_MspDeInit; /* Legacy weak MspDeInit */
break;
default :
/* Update the error code */
hadc->ErrorCode |= HAL_ADC_ERROR_INVALID_CALLBACK;
/* Return error status */
status = HAL_ERROR;
break;
}
}
else if (HAL_ADC_STATE_RESET == hadc->State)
{
switch (CallbackID)
{
case HAL_ADC_MSPINIT_CB_ID :
hadc->MspInitCallback = HAL_ADC_MspInit; /* Legacy weak MspInit */
break;
case HAL_ADC_MSPDEINIT_CB_ID :
hadc->MspDeInitCallback = HAL_ADC_MspDeInit; /* Legacy weak MspDeInit */
break;
default :
/* Update the error code */
hadc->ErrorCode |= HAL_ADC_ERROR_INVALID_CALLBACK;
/* Return error status */
status = HAL_ERROR;
break;
}
}
else
{
/* Update the error code */
hadc->ErrorCode |= HAL_ADC_ERROR_INVALID_CALLBACK;
/* Return error status */
status = HAL_ERROR;
}
return status;
}
#endif /* USE_HAL_ADC_REGISTER_CALLBACKS */
/**
* @}
*/
/** @defgroup ADC_Exported_Functions_Group2 ADC Input and Output operation functions
* @brief ADC IO operation functions
*
@verbatim
===============================================================================
##### IO operation functions #####
===============================================================================
[..] This section provides functions allowing to:
(+) Start conversion of regular group.
(+) Stop conversion of regular group.
(+) Poll for conversion complete on regular group.
(+) Poll for conversion event.
(+) Get result of regular channel conversion.
(+) Start conversion of regular group and enable interruptions.
(+) Stop conversion of regular group and disable interruptions.
(+) Handle ADC interrupt request
(+) Start conversion of regular group and enable DMA transfer.
(+) Stop conversion of regular group and disable ADC DMA transfer.
@endverbatim
* @{
*/
/**
* @brief Enable ADC, start conversion of regular group.
* @note Interruptions enabled in this function: None.
* @param hadc ADC handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_ADC_Start(ADC_HandleTypeDef* hadc)
{
HAL_StatusTypeDef tmp_hal_status = HAL_OK;
/* Check the parameters */
assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
/* Perform ADC enable and conversion start if no conversion is on going */
if (ADC_IS_CONVERSION_ONGOING_REGULAR(hadc) == RESET)
{
/* Process locked */
__HAL_LOCK(hadc);
/* Enable the ADC peripheral */
/* If low power mode AutoPowerOff is enabled, power-on/off phases are */
/* performed automatically by hardware. */
if (hadc->Init.LowPowerAutoPowerOff != ENABLE)
{
tmp_hal_status = ADC_Enable(hadc);
}
/* Start conversion if ADC is effectively enabled */
if (tmp_hal_status == HAL_OK)
{
/* Set ADC state */
/* - Clear state bitfield related to regular group conversion results */
/* - Set state bitfield related to regular operation */
ADC_STATE_CLR_SET(hadc->State,
HAL_ADC_STATE_READY | HAL_ADC_STATE_REG_EOC | HAL_ADC_STATE_REG_OVR | HAL_ADC_STATE_REG_EOSMP,
HAL_ADC_STATE_REG_BUSY);
/* Reset ADC all error code fields */
ADC_CLEAR_ERRORCODE(hadc);
/* Process unlocked */
/* Unlock before starting ADC conversions: in case of potential */
/* interruption, to let the process to ADC IRQ Handler. */
__HAL_UNLOCK(hadc);
/* Clear regular group conversion flag and overrun flag */
/* (To ensure of no unknown state from potential previous ADC */
/* operations) */
__HAL_ADC_CLEAR_FLAG(hadc, (ADC_FLAG_EOC | ADC_FLAG_EOS | ADC_FLAG_OVR));
/* Enable conversion of regular group. */
/* If software start has been selected, conversion starts immediately. */
/* If external trigger has been selected, conversion will start at next */
/* trigger event. */
hadc->Instance->CR |= ADC_CR_ADSTART;
}
}
else
{
tmp_hal_status = HAL_BUSY;
}
/* Return function status */
return tmp_hal_status;
}
/**
* @brief Stop ADC conversion of regular group (and injected channels in
* case of auto_injection mode), disable ADC peripheral.
* @param hadc ADC handle
* @retval HAL status.
*/
HAL_StatusTypeDef HAL_ADC_Stop(ADC_HandleTypeDef* hadc)
{
HAL_StatusTypeDef tmp_hal_status = HAL_OK;
/* Check the parameters */
assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
/* Process locked */
__HAL_LOCK(hadc);
/* 1. Stop potential conversion on going, on ADC group regular */
tmp_hal_status = ADC_ConversionStop(hadc);
/* Disable ADC peripheral if conversions are effectively stopped */
if (tmp_hal_status == HAL_OK)
{
/* 2. Disable the ADC peripheral */
tmp_hal_status = ADC_Disable(hadc);
/* Check if ADC is effectively disabled */
if (tmp_hal_status == HAL_OK)
{
/* Set ADC state */
ADC_STATE_CLR_SET(hadc->State,
HAL_ADC_STATE_REG_BUSY,
HAL_ADC_STATE_READY);
}
}
/* Process unlocked */
__HAL_UNLOCK(hadc);
/* Return function status */
return tmp_hal_status;
}
/**
* @brief Wait for regular group conversion to be completed.
* @note ADC conversion flags EOS (end of sequence) and EOC (end of
* conversion) are cleared by this function, with an exception:
* if low power feature "LowPowerAutoWait" is enabled, flags are
* not cleared to not interfere with this feature until data register
* is read using function HAL_ADC_GetValue().
* @note This function cannot be used in a particular setup: ADC configured
* in DMA mode and polling for end of each conversion (ADC init
* parameter "EOCSelection" set to ADC_EOC_SINGLE_CONV).
* In this case, DMA resets the flag EOC and polling cannot be
* performed on each conversion. Nevertheless, polling can still
* be performed on the complete sequence (ADC init
* parameter "EOCSelection" set to ADC_EOC_SEQ_CONV).
* @param hadc ADC handle
* @param Timeout Timeout value in millisecond.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_ADC_PollForConversion(ADC_HandleTypeDef* hadc, uint32_t Timeout)
{
uint32_t tickstart = 0;
uint32_t tmp_Flag_EOC = 0x00;
/* Check the parameters */
assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
/* If end of conversion selected to end of sequence conversions */
if (hadc->Init.EOCSelection == ADC_EOC_SEQ_CONV)
{
tmp_Flag_EOC = ADC_FLAG_EOS;
}
/* If end of conversion selected to end of unitary conversion */
else /* ADC_EOC_SINGLE_CONV */
{
/* Verification that ADC configuration is compliant with polling for */
/* each conversion: */
/* Particular case is ADC configured in DMA mode and ADC sequencer with */
/* several ranks and polling for end of each conversion. */
/* For code simplicity sake, this particular case is generalized to */
/* ADC configured in DMA mode and and polling for end of each conversion. */
if (HAL_IS_BIT_SET(hadc->Instance->CFGR1, ADC_CFGR1_DMAEN))
{
/* Update ADC state machine to error */
SET_BIT(hadc->State, HAL_ADC_STATE_ERROR_CONFIG);
/* Process unlocked */
__HAL_UNLOCK(hadc);
return HAL_ERROR;
}
else
{
tmp_Flag_EOC = (ADC_FLAG_EOC | ADC_FLAG_EOS);
}
}
/* Get tick count */
tickstart = HAL_GetTick();
/* Wait until End of unitary conversion or sequence conversions flag is raised */
while(HAL_IS_BIT_CLR(hadc->Instance->ISR, tmp_Flag_EOC))
{
/* Check if timeout is disabled (set to infinite wait) */
if(Timeout != HAL_MAX_DELAY)
{
if((Timeout == 0U) || ((HAL_GetTick()-tickstart) > Timeout))
{
/* Update ADC state machine to timeout */
SET_BIT(hadc->State, HAL_ADC_STATE_TIMEOUT);
/* Process unlocked */
__HAL_UNLOCK(hadc);
return HAL_TIMEOUT;
}
}
}
/* Update ADC state machine */
SET_BIT(hadc->State, HAL_ADC_STATE_REG_EOC);
/* Determine whether any further conversion upcoming on group regular */
/* by external trigger, continuous mode or scan sequence on going. */
if(ADC_IS_SOFTWARE_START_REGULAR(hadc) &&
(hadc->Init.ContinuousConvMode == DISABLE) )
{
/* If End of Sequence is reached, disable interrupts */
if( __HAL_ADC_GET_FLAG(hadc, ADC_FLAG_EOS) )
{
/* Allowed to modify bits ADC_IT_EOC/ADC_IT_EOS only if bit */
/* ADSTART==0 (no conversion on going) */
if (ADC_IS_CONVERSION_ONGOING_REGULAR(hadc) == RESET)
{
/* Disable ADC end of single conversion interrupt on group regular */
/* Note: Overrun interrupt was enabled with EOC interrupt in */
/* HAL_Start_IT(), but is not disabled here because can be used */
/* by overrun IRQ process below. */
__HAL_ADC_DISABLE_IT(hadc, ADC_IT_EOC | ADC_IT_EOS);
/* Set ADC state */
ADC_STATE_CLR_SET(hadc->State,
HAL_ADC_STATE_REG_BUSY,
HAL_ADC_STATE_READY);
}
else
{
/* Change ADC state to error state */
SET_BIT(hadc->State, HAL_ADC_STATE_ERROR_CONFIG);
/* Set ADC error code to ADC peripheral internal error */
SET_BIT(hadc->ErrorCode, HAL_ADC_ERROR_INTERNAL);
}
}
}
/* Clear end of conversion flag of regular group if low power feature */
/* "LowPowerAutoWait " is disabled, to not interfere with this feature */
/* until data register is read using function HAL_ADC_GetValue(). */
if (hadc->Init.LowPowerAutoWait == DISABLE)
{
/* Clear regular group conversion flag */
__HAL_ADC_CLEAR_FLAG(hadc, (ADC_FLAG_EOC | ADC_FLAG_EOS));
}
/* Return function status */
return HAL_OK;
}
/**
* @brief Poll for ADC event.
* @param hadc ADC handle
* @param EventType the ADC event type.
* This parameter can be one of the following values:
* @arg ADC_AWD_EVENT: ADC Analog watchdog event
* @arg ADC_OVR_EVENT: ADC Overrun event
* @param Timeout Timeout value in millisecond.
* @note The relevant flag is cleared if found to be set, except for ADC_FLAG_OVR.
* Indeed, the latter is reset only if hadc->Init.Overrun field is set
* to ADC_OVR_DATA_OVERWRITTEN. Otherwise, data register may be potentially overwritten
* by a new converted data as soon as OVR is cleared.
* To reset OVR flag once the preserved data is retrieved, the user can resort
* to macro __HAL_ADC_CLEAR_FLAG(hadc, ADC_FLAG_OVR);
* @retval HAL status
*/
HAL_StatusTypeDef HAL_ADC_PollForEvent(ADC_HandleTypeDef* hadc, uint32_t EventType, uint32_t Timeout)
{
uint32_t tickstart = 0U;
/* Check the parameters */
assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
assert_param(IS_ADC_EVENT_TYPE(EventType));
/* Get tick count */
tickstart = HAL_GetTick();
/* Check selected event flag */
while(__HAL_ADC_GET_FLAG(hadc, EventType) == RESET)
{
/* Check if timeout is disabled (set to infinite wait) */
if(Timeout != HAL_MAX_DELAY)
{
if((Timeout == 0U) ||((HAL_GetTick() - tickstart ) > Timeout))
{
/* Update ADC state machine to timeout */
SET_BIT(hadc->State, HAL_ADC_STATE_TIMEOUT);
/* Process unlocked */
__HAL_UNLOCK(hadc);
return HAL_TIMEOUT;
}
}
}
switch(EventType)
{
/* Analog watchdog (level out of window) event */
case ADC_AWD_EVENT:
/* Set ADC state */
SET_BIT(hadc->State, HAL_ADC_STATE_AWD1);
/* Clear ADC analog watchdog flag */
__HAL_ADC_CLEAR_FLAG(hadc, ADC_FLAG_AWD);
break;
/* Overrun event */
default: /* Case ADC_OVR_EVENT */
/* If overrun is set to overwrite previous data, overrun event is not */
/* considered as an error. */
/* (cf ref manual "Managing conversions without using the DMA and without */
/* overrun ") */
if (hadc->Init.Overrun == ADC_OVR_DATA_PRESERVED)
{
/* Set ADC state */
SET_BIT(hadc->State, HAL_ADC_STATE_REG_OVR);
/* Set ADC error code to overrun */
SET_BIT(hadc->ErrorCode, HAL_ADC_ERROR_OVR);
}
/* Clear ADC Overrun flag */
__HAL_ADC_CLEAR_FLAG(hadc, ADC_FLAG_OVR);
break;
}
/* Return function status */
return HAL_OK;
}
/**
* @brief Enable ADC, start conversion of regular group with interruption.
* @note Interruptions enabled in this function according to initialization
* setting : EOC (end of conversion), EOS (end of sequence),
* OVR overrun.
* Each of these interruptions has its dedicated callback function.
* @note To guarantee a proper reset of all interruptions once all the needed
* conversions are obtained, HAL_ADC_Stop_IT() must be called to ensure
* a correct stop of the IT-based conversions.
* @note By default, HAL_ADC_Start_IT() doesn't enable the End Of Sampling
* interruption. If required (e.g. in case of oversampling with trigger
* mode), the user must:
* 1. first clear the EOSMP flag if set with macro __HAL_ADC_CLEAR_FLAG(hadc, ADC_FLAG_EOSMP)
* 2. then enable the EOSMP interrupt with macro __HAL_ADC_ENABLE_IT(hadc, ADC_IT_EOSMP)
* before calling HAL_ADC_Start_IT().
* @param hadc ADC handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_ADC_Start_IT(ADC_HandleTypeDef* hadc)
{
HAL_StatusTypeDef tmp_hal_status = HAL_OK;
/* Check the parameters */
assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
/* Perform ADC enable and conversion start if no conversion is on going */
if (ADC_IS_CONVERSION_ONGOING_REGULAR(hadc) == RESET)
{
/* Process locked */
__HAL_LOCK(hadc);
/* Enable the ADC peripheral */
/* If low power mode AutoPowerOff is enabled, power-on/off phases are */
/* performed automatically by hardware. */
if (hadc->Init.LowPowerAutoPowerOff != ENABLE)
{
tmp_hal_status = ADC_Enable(hadc);
}
/* Start conversion if ADC is effectively enabled */
if (tmp_hal_status == HAL_OK)
{
/* Set ADC state */
/* - Clear state bitfield related to regular group conversion results */
/* - Set state bitfield related to regular operation */
ADC_STATE_CLR_SET(hadc->State,
HAL_ADC_STATE_READY | HAL_ADC_STATE_REG_EOC | HAL_ADC_STATE_REG_OVR | HAL_ADC_STATE_REG_EOSMP,
HAL_ADC_STATE_REG_BUSY);
/* Reset ADC all error code fields */
ADC_CLEAR_ERRORCODE(hadc);
/* Process unlocked */
/* Unlock before starting ADC conversions: in case of potential */
/* interruption, to let the process to ADC IRQ Handler. */
__HAL_UNLOCK(hadc);
/* Clear regular group conversion flag and overrun flag */
/* (To ensure of no unknown state from potential previous ADC */
/* operations) */
__HAL_ADC_CLEAR_FLAG(hadc, (ADC_FLAG_EOC | ADC_FLAG_EOS | ADC_FLAG_OVR));
/* Enable ADC end of conversion interrupt */
/* Enable ADC overrun interrupt */
switch(hadc->Init.EOCSelection)
{
case ADC_EOC_SEQ_CONV:
__HAL_ADC_DISABLE_IT(hadc, ADC_IT_EOC);
__HAL_ADC_ENABLE_IT(hadc, (ADC_IT_EOS | ADC_IT_OVR));
break;
/* case ADC_EOC_SINGLE_CONV */
default:
__HAL_ADC_ENABLE_IT(hadc, (ADC_IT_EOC | ADC_IT_EOS | ADC_IT_OVR));
break;
}
/* Enable conversion of regular group. */
/* If software start has been selected, conversion starts immediately. */
/* If external trigger has been selected, conversion will start at next */
/* trigger event. */
hadc->Instance->CR |= ADC_CR_ADSTART;
}
}
else
{
tmp_hal_status = HAL_BUSY;
}
/* Return function status */
return tmp_hal_status;
}
/**
* @brief Stop ADC conversion of regular group (and injected group in
* case of auto_injection mode), disable interrution of
* end-of-conversion, disable ADC peripheral.
* @param hadc ADC handle
* @retval HAL status.
*/
HAL_StatusTypeDef HAL_ADC_Stop_IT(ADC_HandleTypeDef* hadc)
{
HAL_StatusTypeDef tmp_hal_status = HAL_OK;
/* Check the parameters */
assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
/* Process locked */
__HAL_LOCK(hadc);
/* 1. Stop potential conversion on going, on ADC group regular */
tmp_hal_status = ADC_ConversionStop(hadc);
/* Disable ADC peripheral if conversions are effectively stopped */
if (tmp_hal_status == HAL_OK)
{
/* Disable ADC end of conversion interrupt for regular group */
/* Disable ADC overrun interrupt */
__HAL_ADC_DISABLE_IT(hadc, (ADC_IT_EOC | ADC_IT_EOS | ADC_IT_OVR));
/* 2. Disable the ADC peripheral */
tmp_hal_status = ADC_Disable(hadc);
/* Check if ADC is effectively disabled */
if (tmp_hal_status == HAL_OK)
{
/* Set ADC state */
ADC_STATE_CLR_SET(hadc->State,
HAL_ADC_STATE_REG_BUSY,
HAL_ADC_STATE_READY);
}
}
/* Process unlocked */
__HAL_UNLOCK(hadc);
/* Return function status */
return tmp_hal_status;
}
/**
* @brief Enable ADC, start conversion of regular group and transfer result through DMA.
* @note Interruptions enabled in this function:
* overrun (if applicable), DMA half transfer, DMA transfer complete.
* Each of these interruptions has its dedicated callback function.
* @param hadc ADC handle
* @param pData Destination Buffer address.
* @param Length Length of data to be transferred from ADC peripheral to memory (in bytes)
* @retval HAL status.
*/
HAL_StatusTypeDef HAL_ADC_Start_DMA(ADC_HandleTypeDef* hadc, uint32_t* pData, uint32_t Length)
{
HAL_StatusTypeDef tmp_hal_status = HAL_OK;
/* Check the parameters */
assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
/* Perform ADC enable and conversion start if no conversion is on going */
if (ADC_IS_CONVERSION_ONGOING_REGULAR(hadc) == RESET)
{
/* Process locked */
__HAL_LOCK(hadc);
/* Enable ADC DMA mode */
hadc->Instance->CFGR1 |= ADC_CFGR1_DMAEN;
/* Enable the ADC peripheral */
/* If low power mode AutoPowerOff is enabled, power-on/off phases are */
/* performed automatically by hardware. */
if (hadc->Init.LowPowerAutoPowerOff != ENABLE)
{
tmp_hal_status = ADC_Enable(hadc);
}
/* Start conversion if ADC is effectively enabled */
if (tmp_hal_status == HAL_OK)
{
/* Set ADC state */
/* - Clear state bitfield related to regular group conversion results */
/* - Set state bitfield related to regular operation */
ADC_STATE_CLR_SET(hadc->State,
HAL_ADC_STATE_READY | HAL_ADC_STATE_REG_EOC | HAL_ADC_STATE_REG_OVR | HAL_ADC_STATE_REG_EOSMP,
HAL_ADC_STATE_REG_BUSY);
/* Reset ADC all error code fields */
ADC_CLEAR_ERRORCODE(hadc);
/* Process unlocked */
/* Unlock before starting ADC conversions: in case of potential */
/* interruption, to let the process to ADC IRQ Handler. */
__HAL_UNLOCK(hadc);
/* Set the DMA transfer complete callback */
hadc->DMA_Handle->XferCpltCallback = ADC_DMAConvCplt;
/* Set the DMA half transfer complete callback */
hadc->DMA_Handle->XferHalfCpltCallback = ADC_DMAHalfConvCplt;
/* Set the DMA error callback */
hadc->DMA_Handle->XferErrorCallback = ADC_DMAError;
/* Manage ADC and DMA start: ADC overrun interruption, DMA start, ADC */
/* start (in case of SW start): */
/* Clear regular group conversion flag and overrun flag */
/* (To ensure of no unknown state from potential previous ADC */
/* operations) */
__HAL_ADC_CLEAR_FLAG(hadc, (ADC_FLAG_EOC | ADC_FLAG_EOS | ADC_FLAG_OVR));
/* Enable ADC overrun interrupt */
__HAL_ADC_ENABLE_IT(hadc, ADC_IT_OVR);
/* Start the DMA channel */
HAL_DMA_Start_IT(hadc->DMA_Handle, (uint32_t)&hadc->Instance->DR, (uint32_t)pData, Length);
/* Enable conversion of regular group. */
/* If software start has been selected, conversion starts immediately. */
/* If external trigger has been selected, conversion will start at next */
/* trigger event. */
hadc->Instance->CR |= ADC_CR_ADSTART;
}
}
else
{
tmp_hal_status = HAL_BUSY;
}
/* Return function status */
return tmp_hal_status;
}
/**
* @brief Stop ADC conversion of regular group (and injected group in
* case of auto_injection mode), disable ADC DMA transfer, disable
* ADC peripheral.
* Each of these interruptions has its dedicated callback function.
* @param hadc ADC handle
* @retval HAL status.
*/
HAL_StatusTypeDef HAL_ADC_Stop_DMA(ADC_HandleTypeDef* hadc)
{
HAL_StatusTypeDef tmp_hal_status = HAL_OK;
/* Check the parameters */
assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
/* Process locked */
__HAL_LOCK(hadc);
/* 1. Stop potential ADC group regular conversion on going */
tmp_hal_status = ADC_ConversionStop(hadc);
/* Disable ADC peripheral if conversions are effectively stopped */
if (tmp_hal_status == HAL_OK)
{
/* Disable ADC DMA (ADC DMA configuration ADC_CFGR_DMACFG is kept) */
CLEAR_BIT(hadc->Instance->CFGR1, ADC_CFGR1_DMAEN);
/* Disable the DMA channel (in case of DMA in circular mode or stop */
/* while DMA transfer is on going) */
if (hadc->DMA_Handle->State == HAL_DMA_STATE_BUSY)
{
tmp_hal_status = HAL_DMA_Abort(hadc->DMA_Handle);
/* Check if DMA channel effectively disabled */
if (tmp_hal_status != HAL_OK)
{
/* Update ADC state machine to error */
SET_BIT(hadc->State, HAL_ADC_STATE_ERROR_DMA);
}
}
/* Disable ADC overrun interrupt */
__HAL_ADC_DISABLE_IT(hadc, ADC_IT_OVR);
/* 2. Disable the ADC peripheral */
/* Update "tmp_hal_status" only if DMA channel disabling passed, to keep */
/* in memory a potential failing status. */
if (tmp_hal_status == HAL_OK)
{
tmp_hal_status = ADC_Disable(hadc);
}
else
{
ADC_Disable(hadc);
}
/* Check if ADC is effectively disabled */
if (tmp_hal_status == HAL_OK)
{
/* Set ADC state */
ADC_STATE_CLR_SET(hadc->State,
HAL_ADC_STATE_REG_BUSY,
HAL_ADC_STATE_READY);
}
}
/* Process unlocked */
__HAL_UNLOCK(hadc);
/* Return function status */
return tmp_hal_status;
}
/**
* @brief Get ADC regular group conversion result.
* @note Reading register DR automatically clears ADC flag EOC
* (ADC group regular end of unitary conversion).
* @note This function does not clear ADC flag EOS
* (ADC group regular end of sequence conversion).
* Occurrence of flag EOS rising:
* - If sequencer is composed of 1 rank, flag EOS is equivalent
* to flag EOC.
* - If sequencer is composed of several ranks, during the scan
* sequence flag EOC only is raised, at the end of the scan sequence
* both flags EOC and EOS are raised.
* To clear this flag, either use function:
* in programming model IT: @ref HAL_ADC_IRQHandler(), in programming
* model polling: @ref HAL_ADC_PollForConversion()
* or @ref __HAL_ADC_CLEAR_FLAG(&hadc, ADC_FLAG_EOS).
* @param hadc ADC handle
* @retval ADC group regular conversion data
*/
uint32_t HAL_ADC_GetValue(ADC_HandleTypeDef* hadc)
{
/* Check the parameters */
assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
/* Note: EOC flag is not cleared here by software because automatically */
/* cleared by hardware when reading register DR. */
/* Return ADC converted value */
return hadc->Instance->DR;
}
/**
* @brief Handle ADC interrupt request.
* @param hadc ADC handle
* @retval None
*/
void HAL_ADC_IRQHandler(ADC_HandleTypeDef* hadc)
{
/* Check the parameters */
assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
assert_param(IS_FUNCTIONAL_STATE(hadc->Init.ContinuousConvMode));
assert_param(IS_ADC_EOC_SELECTION(hadc->Init.EOCSelection));
/* ========== Check End of Conversion flag for regular group ========== */
if( (__HAL_ADC_GET_FLAG(hadc, ADC_FLAG_EOC) && __HAL_ADC_GET_IT_SOURCE(hadc, ADC_IT_EOC)) ||
(__HAL_ADC_GET_FLAG(hadc, ADC_FLAG_EOS) && __HAL_ADC_GET_IT_SOURCE(hadc, ADC_IT_EOS)) )
{
/* Update state machine on conversion status if not in error state */
if (HAL_IS_BIT_CLR(hadc->State, HAL_ADC_STATE_ERROR_INTERNAL))
{
/* Set ADC state */
SET_BIT(hadc->State, HAL_ADC_STATE_REG_EOC);
}
/* Determine whether any further conversion upcoming on group regular */
/* by external trigger, continuous mode or scan sequence on going. */
if(ADC_IS_SOFTWARE_START_REGULAR(hadc) &&
(hadc->Init.ContinuousConvMode == DISABLE) )
{
/* If End of Sequence is reached, disable interrupts */
if( __HAL_ADC_GET_FLAG(hadc, ADC_FLAG_EOS) )
{
/* Allowed to modify bits ADC_IT_EOC/ADC_IT_EOS only if bit */
/* ADSTART==0 (no conversion on going) */
if (ADC_IS_CONVERSION_ONGOING_REGULAR(hadc) == RESET)
{
/* Disable ADC end of single conversion interrupt on group regular */
/* Note: Overrun interrupt was enabled with EOC interrupt in */
/* HAL_Start_IT(), but is not disabled here because can be used */
/* by overrun IRQ process below. */
__HAL_ADC_DISABLE_IT(hadc, ADC_IT_EOC | ADC_IT_EOS);
/* Set ADC state */
ADC_STATE_CLR_SET(hadc->State,
HAL_ADC_STATE_REG_BUSY,
HAL_ADC_STATE_READY);
}
else
{
/* Change ADC state to error state */
SET_BIT(hadc->State, HAL_ADC_STATE_ERROR_CONFIG);
/* Set ADC error code to ADC peripheral internal error */
SET_BIT(hadc->ErrorCode, HAL_ADC_ERROR_INTERNAL);
}
}
}
/* Note: into callback, to determine if conversion has been triggered */
/* from EOC or EOS, possibility to use: */
/* " if( __HAL_ADC_GET_FLAG(&hadc, ADC_FLAG_EOS)) " */
#if (USE_HAL_ADC_REGISTER_CALLBACKS == 1)
hadc->ConvCpltCallback(hadc);
#else
HAL_ADC_ConvCpltCallback(hadc);
#endif /* USE_HAL_ADC_REGISTER_CALLBACKS */
/* Clear regular group conversion flag */
/* Note: in case of overrun set to ADC_OVR_DATA_PRESERVED, end of */
/* conversion flags clear induces the release of the preserved data.*/
/* Therefore, if the preserved data value is needed, it must be */
/* read preliminarily into HAL_ADC_ConvCpltCallback(). */
/* Note: Management of low power auto-wait enabled: flags must be cleared */
/* by user when fetching ADC conversion data. */
/* This case is managed in IRQ handler, but this low-power mode */
/* should not be used with programming model IT or DMA. */
/* Refer to comment of parameter "LowPowerAutoWait". */
if (hadc->Init.LowPowerAutoWait != ENABLE)
{
__HAL_ADC_CLEAR_FLAG(hadc, (ADC_FLAG_EOC | ADC_FLAG_EOS));
}
}
/* ========== Check analog watchdog 1 flag ========== */
if(__HAL_ADC_GET_FLAG(hadc, ADC_FLAG_AWD) && __HAL_ADC_GET_IT_SOURCE(hadc, ADC_IT_AWD))
{
/* Set ADC state */
SET_BIT(hadc->State, HAL_ADC_STATE_AWD1);
#if (USE_HAL_ADC_REGISTER_CALLBACKS == 1)
hadc->LevelOutOfWindowCallback(hadc);
#else
HAL_ADC_LevelOutOfWindowCallback(hadc);
#endif /* USE_HAL_ADC_REGISTER_CALLBACKS */
/* Clear ADC Analog watchdog flag */
__HAL_ADC_CLEAR_FLAG(hadc, ADC_FLAG_AWD);
}
/* ========== Check Overrun flag ========== */
if(__HAL_ADC_GET_FLAG(hadc, ADC_FLAG_OVR) && __HAL_ADC_GET_IT_SOURCE(hadc, ADC_IT_OVR))
{
/* If overrun is set to overwrite previous data (default setting), */
/* overrun event is not considered as an error. */
/* (cf ref manual "Managing conversions without using the DMA and without */
/* overrun ") */
/* Exception for usage with DMA overrun event always considered as an */
/* error. */
if ((hadc->Init.Overrun == ADC_OVR_DATA_PRESERVED) ||
HAL_IS_BIT_SET(hadc->Instance->CFGR1, ADC_CFGR1_DMAEN) )
{
/* Set ADC error code to overrun */
SET_BIT(hadc->ErrorCode, HAL_ADC_ERROR_OVR);
/* Clear ADC overrun flag */
__HAL_ADC_CLEAR_FLAG(hadc, ADC_FLAG_OVR);
#if (USE_HAL_ADC_REGISTER_CALLBACKS == 1)
hadc->ErrorCallback(hadc);
#else
HAL_ADC_ErrorCallback(hadc);
#endif /* USE_HAL_ADC_REGISTER_CALLBACKS */
}
/* Clear the Overrun flag */
__HAL_ADC_CLEAR_FLAG(hadc, ADC_FLAG_OVR);
}
}
/**
* @brief Conversion complete callback in non-blocking mode.
* @param hadc ADC handle
* @retval None
*/
__weak void HAL_ADC_ConvCpltCallback(ADC_HandleTypeDef* hadc)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hadc);
/* NOTE : This function should not be modified. When the callback is needed,
function HAL_ADC_ConvCpltCallback must be implemented in the user file.
*/
}
/**
* @brief Conversion DMA half-transfer callback in non-blocking mode.
* @param hadc ADC handle
* @retval None
*/
__weak void HAL_ADC_ConvHalfCpltCallback(ADC_HandleTypeDef* hadc)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hadc);
/* NOTE : This function should not be modified. When the callback is needed,
function HAL_ADC_ConvHalfCpltCallback must be implemented in the user file.
*/
}
/**
* @brief Analog watchdog 1 callback in non-blocking mode.
* @param hadc ADC handle
* @retval None
*/
__weak void HAL_ADC_LevelOutOfWindowCallback(ADC_HandleTypeDef* hadc)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hadc);
/* NOTE : This function should not be modified. When the callback is needed,
function HAL_ADC_LevelOutOfWindowCallback must be implemented in the user file.
*/
}
/**
* @brief ADC error callback in non-blocking mode
* (ADC conversion with interruption or transfer by DMA).
* @note In case of error due to overrun when using ADC with DMA transfer
* (HAL ADC handle paramater "ErrorCode" to state "HAL_ADC_ERROR_OVR"):
* - Reinitialize the DMA using function "HAL_ADC_Stop_DMA()".
* - If needed, restart a new ADC conversion using function
* "HAL_ADC_Start_DMA()"
* (this function is also clearing overrun flag)
* @param hadc ADC handle
* @retval None
*/
__weak void HAL_ADC_ErrorCallback(ADC_HandleTypeDef *hadc)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hadc);
/* NOTE : This function should not be modified. When the callback is needed,
function HAL_ADC_ErrorCallback must be implemented in the user file.
*/
}
/**
* @}
*/
/** @defgroup ADC_Exported_Functions_Group3 Peripheral Control functions
* @brief Peripheral Control functions
*
@verbatim
===============================================================================
##### Peripheral Control functions #####
===============================================================================
[..] This section provides functions allowing to:
(+) Configure channels on regular group
(+) Configure the analog watchdog
@endverbatim
* @{
*/
/**
* @brief Configure a channel to be assigned to ADC group regular.
* @note In case of usage of internal measurement channels:
* VrefInt/Vlcd(STM32L0x3xx only)/TempSensor.
* Sampling time constraints must be respected (sampling time can be
* adjusted in function of ADC clock frequency and sampling time
* setting).
* Refer to device datasheet for timings values, parameters TS_vrefint,
* TS_vlcd (STM32L0x3xx only), TS_temp (values rough order: 5us to 17us).
* These internal paths can be be disabled using function
* HAL_ADC_DeInit().
* @note Possibility to update parameters on the fly:
* This function initializes channel into ADC group regular,
* following calls to this function can be used to reconfigure
* some parameters of structure "ADC_ChannelConfTypeDef" on the fly,
* without resetting the ADC.
* The setting of these parameters is conditioned to ADC state:
* Refer to comments of structure "ADC_ChannelConfTypeDef".
* @param hadc ADC handle
* @param sConfig Structure of ADC channel assigned to ADC group regular.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_ADC_ConfigChannel(ADC_HandleTypeDef* hadc, ADC_ChannelConfTypeDef* sConfig)
{
/* Check the parameters */
assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
assert_param(IS_ADC_CHANNEL(sConfig->Channel));
assert_param(IS_ADC_RANK(sConfig->Rank));
/* Process locked */
__HAL_LOCK(hadc);
/* Parameters update conditioned to ADC state: */
/* Parameters that can be updated when ADC is disabled or enabled without */
/* conversion on going on regular group: */
/* - Channel number */
/* - Management of internal measurement channels: Vbat/VrefInt/TempSensor */
if (ADC_IS_CONVERSION_ONGOING_REGULAR(hadc) != RESET)
{
/* Update ADC state machine to error */
SET_BIT(hadc->State, HAL_ADC_STATE_ERROR_CONFIG);
/* Process unlocked */
__HAL_UNLOCK(hadc);
return HAL_ERROR;
}
if (sConfig->Rank != ADC_RANK_NONE)
{
/* Enable selected channels */
hadc->Instance->CHSELR |= (uint32_t)(sConfig->Channel & ADC_CHANNEL_MASK);
/* Management of internal measurement channels: Vlcd (STM32L0x3xx only)/VrefInt/TempSensor */
/* internal measurement paths enable: If internal channel selected, enable */
/* dedicated internal buffers and path. */
#if defined(ADC_CCR_TSEN)
/* If Temperature sensor channel is selected, then enable the internal */
/* buffers and path */
if (((sConfig->Channel & ADC_CHANNEL_MASK) & ADC_CHANNEL_TEMPSENSOR ) == (ADC_CHANNEL_TEMPSENSOR & ADC_CHANNEL_MASK))
{
ADC->CCR |= ADC_CCR_TSEN;
/* Delay for temperature sensor stabilization time */
ADC_DelayMicroSecond(ADC_TEMPSENSOR_DELAY_US);
}
#endif
/* If VRefInt channel is selected, then enable the internal buffers and path */
if (((sConfig->Channel & ADC_CHANNEL_MASK) & ADC_CHANNEL_VREFINT) == (ADC_CHANNEL_VREFINT & ADC_CHANNEL_MASK))
{
ADC->CCR |= ADC_CCR_VREFEN;
}
#if defined (STM32L053xx) || defined (STM32L063xx) || defined (STM32L073xx) || defined (STM32L083xx)
/* If Vlcd channel is selected, then enable the internal buffers and path */
if (((sConfig->Channel & ADC_CHANNEL_MASK) & ADC_CHANNEL_VLCD) == (ADC_CHANNEL_VLCD & ADC_CHANNEL_MASK))
{
ADC->CCR |= ADC_CCR_VLCDEN;
}
#endif
}
else
{
/* Regular sequence configuration */
/* Reset the channel selection register from the selected channel */
hadc->Instance->CHSELR &= ~((uint32_t)(sConfig->Channel & ADC_CHANNEL_MASK));
/* Management of internal measurement channels: VrefInt/TempSensor/Vbat */
/* internal measurement paths disable: If internal channel selected, */
/* disable dedicated internal buffers and path. */
#if defined(ADC_CCR_TSEN)
if (((sConfig->Channel & ADC_CHANNEL_MASK) & ADC_CHANNEL_TEMPSENSOR ) == (ADC_CHANNEL_TEMPSENSOR & ADC_CHANNEL_MASK))
{
ADC->CCR &= ~ADC_CCR_TSEN;
}
#endif
/* If VRefInt channel is selected, then enable the internal buffers and path */
if (((sConfig->Channel & ADC_CHANNEL_MASK) & ADC_CHANNEL_VREFINT) == (ADC_CHANNEL_VREFINT & ADC_CHANNEL_MASK))
{
ADC->CCR &= ~ADC_CCR_VREFEN;
}
#if defined (STM32L053xx) || defined (STM32L063xx) || defined (STM32L073xx) || defined (STM32L083xx)
/* If Vlcd channel is selected, then enable the internal buffers and path */
if (((sConfig->Channel & ADC_CHANNEL_MASK) & ADC_CHANNEL_VLCD) == (ADC_CHANNEL_VLCD & ADC_CHANNEL_MASK))
{
ADC->CCR &= ~ADC_CCR_VLCDEN;
}
#endif
}
/* Process unlocked */
__HAL_UNLOCK(hadc);
/* Return function status */
return HAL_OK;
}
/**
* @brief Configure the analog watchdog.
* @note Possibility to update parameters on the fly:
* This function initializes the selected analog watchdog, successive
* calls to this function can be used to reconfigure some parameters
* of structure "ADC_AnalogWDGConfTypeDef" on the fly, without resetting
* the ADC.
* The setting of these parameters is conditioned to ADC state.
* For parameters constraints, see comments of structure
* "ADC_AnalogWDGConfTypeDef".
* @note Analog watchdog thresholds can be modified while ADC conversion
* is on going.
* In this case, some constraints must be taken into account:
* the programmed threshold values are effective from the next
* ADC EOC (end of unitary conversion).
* Considering that registers write delay may happen due to
* bus activity, this might cause an uncertainty on the
* effective timing of the new programmed threshold values.
* @param hadc ADC handle
* @param AnalogWDGConfig Structure of ADC analog watchdog configuration
* @retval HAL status
*/
HAL_StatusTypeDef HAL_ADC_AnalogWDGConfig(ADC_HandleTypeDef* hadc, ADC_AnalogWDGConfTypeDef* AnalogWDGConfig)
{
HAL_StatusTypeDef tmp_hal_status = HAL_OK;
uint32_t tmpAWDHighThresholdShifted;
uint32_t tmpAWDLowThresholdShifted;
/* Check the parameters */
assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
assert_param(IS_ADC_ANALOG_WATCHDOG_MODE(AnalogWDGConfig->WatchdogMode));
assert_param(IS_FUNCTIONAL_STATE(AnalogWDGConfig->ITMode));
if(AnalogWDGConfig->WatchdogMode == ADC_ANALOGWATCHDOG_SINGLE_REG)
{
assert_param(IS_ADC_CHANNEL(AnalogWDGConfig->Channel));
}
/* Verify if threshold is within the selected ADC resolution */
assert_param(IS_ADC_RANGE(ADC_GET_RESOLUTION(hadc), AnalogWDGConfig->HighThreshold));
assert_param(IS_ADC_RANGE(ADC_GET_RESOLUTION(hadc), AnalogWDGConfig->LowThreshold));
/* Process locked */
__HAL_LOCK(hadc);
/* Parameters update conditioned to ADC state: */
/* Parameters that can be updated when ADC is disabled or enabled without */
/* conversion on going on regular group: */
/* - Analog watchdog channels */
/* - Analog watchdog thresholds */
if (ADC_IS_CONVERSION_ONGOING_REGULAR(hadc) == RESET)
{
/* Configure ADC Analog watchdog interrupt */
if(AnalogWDGConfig->ITMode == ENABLE)
{
/* Enable the ADC Analog watchdog interrupt */
__HAL_ADC_ENABLE_IT(hadc, ADC_IT_AWD);
}
else
{
/* Disable the ADC Analog watchdog interrupt */
__HAL_ADC_DISABLE_IT(hadc, ADC_IT_AWD);
}
/* Configuration of analog watchdog: */
/* - Set the analog watchdog mode */
/* - Set the Analog watchdog channel (is not used if watchdog */
/* mode "all channels": ADC_CFGR1_AWD1SGL=0) */
hadc->Instance->CFGR1 &= ~( ADC_CFGR1_AWDSGL |
ADC_CFGR1_AWDEN |
ADC_CFGR1_AWDCH);
hadc->Instance->CFGR1 |= ( AnalogWDGConfig->WatchdogMode |
(AnalogWDGConfig->Channel & ADC_CHANNEL_AWD_MASK));
/* Shift the offset in function of the selected ADC resolution: Thresholds */
/* have to be left-aligned on bit 11, the LSB (right bits) are set to 0 */
tmpAWDHighThresholdShifted = ADC_AWD1THRESHOLD_SHIFT_RESOLUTION(hadc, AnalogWDGConfig->HighThreshold);
tmpAWDLowThresholdShifted = ADC_AWD1THRESHOLD_SHIFT_RESOLUTION(hadc, AnalogWDGConfig->LowThreshold);
/* Clear High & Low high thresholds */
hadc->Instance->TR &= (uint32_t) ~ (ADC_TR_HT | ADC_TR_LT);
/* Set the high threshold */
hadc->Instance->TR = ADC_TRX_HIGHTHRESHOLD (tmpAWDHighThresholdShifted);
/* Set the low threshold */
hadc->Instance->TR |= tmpAWDLowThresholdShifted;
}
/* If a conversion is on going on regular group, no update could be done */
/* on neither of the AWD configuration structure parameters. */
else
{
/* Update ADC state machine to error */
SET_BIT(hadc->State, HAL_ADC_STATE_ERROR_CONFIG);
tmp_hal_status = HAL_ERROR;
}
/* Process unlocked */
__HAL_UNLOCK(hadc);
/* Return function status */
return tmp_hal_status;
}
/**
* @}
*/
/** @defgroup ADC_Exported_Functions_Group4 Peripheral State functions
* @brief ADC Peripheral State functions
*
@verbatim
===============================================================================
##### Peripheral state and errors functions #####
===============================================================================
[..]
This subsection provides functions to get in run-time the status of the
peripheral.
(+) Check the ADC state
(+) Check the ADC error code
@endverbatim
* @{
*/
/**
* @brief Return the ADC handle state.
* @note ADC state machine is managed by bitfields, ADC status must be
* compared with states bits.
* For example:
* " if (HAL_IS_BIT_SET(HAL_ADC_GetState(hadc1), HAL_ADC_STATE_REG_BUSY)) "
* " if (HAL_IS_BIT_SET(HAL_ADC_GetState(hadc1), HAL_ADC_STATE_AWD1) ) "
* @param hadc ADC handle
* @retval ADC handle state (bitfield on 32 bits)
*/
uint32_t HAL_ADC_GetState(ADC_HandleTypeDef* hadc)
{
/* Check the parameters */
assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
/* Return ADC handle state */
return hadc->State;
}
/**
* @brief Return the ADC error code.
* @param hadc ADC handle
* @retval ADC error code (bitfield on 32 bits)
*/
uint32_t HAL_ADC_GetError(ADC_HandleTypeDef *hadc)
{
/* Check the parameters */
assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
return hadc->ErrorCode;
}
/**
* @}
*/
/**
* @}
*/
/** @defgroup ADC_Private_Functions ADC Private Functions
* @{
*/
/**
* @brief Enable the selected ADC.
* @note Prerequisite condition to use this function: ADC must be disabled
* and voltage regulator must be enabled (done into HAL_ADC_Init()).
* @note If low power mode AutoPowerOff is enabled, power-on/off phases are
* performed automatically by hardware.
* In this mode, this function is useless and must not be called because
* flag ADC_FLAG_RDY is not usable.
* Therefore, this function must be called under condition of
* "if (hadc->Init.LowPowerAutoPowerOff != ENABLE)".
* @param hadc ADC handle
* @retval HAL status.
*/
static HAL_StatusTypeDef ADC_Enable(ADC_HandleTypeDef* hadc)
{
uint32_t tickstart = 0U;
/* ADC enable and wait for ADC ready (in case of ADC is disabled or */
/* enabling phase not yet completed: flag ADC ready not yet set). */
/* Timeout implemented to not be stuck if ADC cannot be enabled (possible */
/* causes: ADC clock not running, ...). */
if (ADC_IS_ENABLE(hadc) == RESET)
{
/* Check if conditions to enable the ADC are fulfilled */
if (ADC_ENABLING_CONDITIONS(hadc) == RESET)
{
/* Update ADC state machine to error */
SET_BIT(hadc->State, HAL_ADC_STATE_ERROR_INTERNAL);
/* Set ADC error code to ADC peripheral internal error */
SET_BIT(hadc->ErrorCode, HAL_ADC_ERROR_INTERNAL);
return HAL_ERROR;
}
/* Enable the ADC peripheral */
__HAL_ADC_ENABLE(hadc);
/* Delay for ADC stabilization time. */
ADC_DelayMicroSecond(ADC_STAB_DELAY_US);
/* Get tick count */
tickstart = HAL_GetTick();
/* Wait for ADC effectively enabled */
while(__HAL_ADC_GET_FLAG(hadc, ADC_FLAG_RDY) == RESET)
{
if((HAL_GetTick() - tickstart) > ADC_ENABLE_TIMEOUT)
{
/* Update ADC state machine to error */
SET_BIT(hadc->State, HAL_ADC_STATE_ERROR_INTERNAL);
/* Set ADC error code to ADC peripheral internal error */
SET_BIT(hadc->ErrorCode, HAL_ADC_ERROR_INTERNAL);
return HAL_ERROR;
}
}
}
/* Return HAL status */
return HAL_OK;
}
/**
* @brief Disable the selected ADC.
* @note Prerequisite condition to use this function: ADC conversions must be
* stopped.
* @param hadc ADC handle
* @retval HAL status.
*/
static HAL_StatusTypeDef ADC_Disable(ADC_HandleTypeDef* hadc)
{
uint32_t tickstart = 0U;
/* Verification if ADC is not already disabled: */
/* Note: forbidden to disable ADC (set bit ADC_CR_ADDIS) if ADC is already */
/* disabled. */
if (ADC_IS_ENABLE(hadc) != RESET)
{
/* Check if conditions to disable the ADC are fulfilled */
if (ADC_DISABLING_CONDITIONS(hadc) != RESET)
{
/* Disable the ADC peripheral */
__HAL_ADC_DISABLE(hadc);
}
else
{
/* Update ADC state machine to error */
SET_BIT(hadc->State, HAL_ADC_STATE_ERROR_INTERNAL);
/* Set ADC error code to ADC peripheral internal error */
SET_BIT(hadc->ErrorCode, HAL_ADC_ERROR_INTERNAL);
return HAL_ERROR;
}
/* Wait for ADC effectively disabled */
/* Get tick count */
tickstart = HAL_GetTick();
while(HAL_IS_BIT_SET(hadc->Instance->CR, ADC_CR_ADEN))
{
if((HAL_GetTick() - tickstart) > ADC_DISABLE_TIMEOUT)
{
/* Update ADC state machine to error */
SET_BIT(hadc->State, HAL_ADC_STATE_ERROR_INTERNAL);
/* Set ADC error code to ADC peripheral internal error */
SET_BIT(hadc->ErrorCode, HAL_ADC_ERROR_INTERNAL);
return HAL_ERROR;
}
}
}
/* Return HAL status */
return HAL_OK;
}
/**
* @brief Stop ADC conversion.
* @note Prerequisite condition to use this function: ADC conversions must be
* stopped to disable the ADC.
* @param hadc ADC handle
* @retval HAL status.
*/
static HAL_StatusTypeDef ADC_ConversionStop(ADC_HandleTypeDef* hadc)
{
uint32_t tickstart = 0U;
/* Check the parameters */
assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
/* Verification if ADC is not already stopped on regular group to bypass */
/* this function if not needed. */
if (ADC_IS_CONVERSION_ONGOING_REGULAR(hadc))
{
/* Stop potential conversion on going on regular group */
/* Software is allowed to set ADSTP only when ADSTART=1 and ADDIS=0 */
if (HAL_IS_BIT_SET(hadc->Instance->CR, ADC_CR_ADSTART) &&
HAL_IS_BIT_CLR(hadc->Instance->CR, ADC_CR_ADDIS) )
{
/* Stop conversions on regular group */
hadc->Instance->CR |= ADC_CR_ADSTP;
}
/* Wait for conversion effectively stopped */
/* Get tick count */
tickstart = HAL_GetTick();
while((hadc->Instance->CR & ADC_CR_ADSTART) != RESET)
{
if((HAL_GetTick() - tickstart) > ADC_STOP_CONVERSION_TIMEOUT)
{
/* Update ADC state machine to error */
SET_BIT(hadc->State, HAL_ADC_STATE_ERROR_INTERNAL);
/* Set ADC error code to ADC peripheral internal error */
SET_BIT(hadc->ErrorCode, HAL_ADC_ERROR_INTERNAL);
return HAL_ERROR;
}
}
}
/* Return HAL status */
return HAL_OK;
}
/**
* @brief DMA transfer complete callback.
* @param hdma pointer to DMA handle.
* @retval None
*/
static void ADC_DMAConvCplt(DMA_HandleTypeDef *hdma)
{
/* Retrieve ADC handle corresponding to current DMA handle */
ADC_HandleTypeDef* hadc = ( ADC_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;
/* Update state machine on conversion status if not in error state */
if (HAL_IS_BIT_CLR(hadc->State, HAL_ADC_STATE_ERROR_INTERNAL | HAL_ADC_STATE_ERROR_DMA))
{
/* Set ADC state */
SET_BIT(hadc->State, HAL_ADC_STATE_REG_EOC);
/* Determine whether any further conversion upcoming on group regular */
/* by external trigger, continuous mode or scan sequence on going. */
if(ADC_IS_SOFTWARE_START_REGULAR(hadc) &&
(hadc->Init.ContinuousConvMode == DISABLE) )
{
/* If End of Sequence is reached, disable interrupts */
if( __HAL_ADC_GET_FLAG(hadc, ADC_FLAG_EOS) )
{
/* Allowed to modify bits ADC_IT_EOC/ADC_IT_EOS only if bit */
/* ADSTART==0 (no conversion on going) */
if (ADC_IS_CONVERSION_ONGOING_REGULAR(hadc) == RESET)
{
/* Disable ADC end of single conversion interrupt on group regular */
/* Note: Overrun interrupt was enabled with EOC interrupt in */
/* HAL_Start_IT(), but is not disabled here because can be used */
/* by overrun IRQ process below. */
__HAL_ADC_DISABLE_IT(hadc, ADC_IT_EOC | ADC_IT_EOS);
/* Set ADC state */
ADC_STATE_CLR_SET(hadc->State,
HAL_ADC_STATE_REG_BUSY,
HAL_ADC_STATE_READY);
}
else
{
/* Change ADC state to error state */
SET_BIT(hadc->State, HAL_ADC_STATE_ERROR_CONFIG);
/* Set ADC error code to ADC peripheral internal error */
SET_BIT(hadc->ErrorCode, HAL_ADC_ERROR_INTERNAL);
}
}
}
/* Conversion complete callback */
#if (USE_HAL_ADC_REGISTER_CALLBACKS == 1)
hadc->ConvCpltCallback(hadc);
#else
HAL_ADC_ConvCpltCallback(hadc);
#endif /* USE_HAL_ADC_REGISTER_CALLBACKS */
}
else
{
/* Call DMA error callback */
hadc->DMA_Handle->XferErrorCallback(hdma);
}
}
/**
* @brief DMA half transfer complete callback.
* @param hdma pointer to DMA handle.
* @retval None
*/
static void ADC_DMAHalfConvCplt(DMA_HandleTypeDef *hdma)
{
/* Retrieve ADC handle corresponding to current DMA handle */
ADC_HandleTypeDef* hadc = ( ADC_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;
/* Half conversion callback */
#if (USE_HAL_ADC_REGISTER_CALLBACKS == 1)
hadc->ConvHalfCpltCallback(hadc);
#else
HAL_ADC_ConvHalfCpltCallback(hadc);
#endif /* USE_HAL_ADC_REGISTER_CALLBACKS */
}
/**
* @brief DMA error callback.
* @param hdma pointer to DMA handle.
* @retval None
*/
static void ADC_DMAError(DMA_HandleTypeDef *hdma)
{
/* Retrieve ADC handle corresponding to current DMA handle */
ADC_HandleTypeDef* hadc = ( ADC_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;
/* Set ADC state */
SET_BIT(hadc->State, HAL_ADC_STATE_ERROR_DMA);
/* Set ADC error code to DMA error */
SET_BIT(hadc->ErrorCode, HAL_ADC_ERROR_DMA);
/* Error callback */
#if (USE_HAL_ADC_REGISTER_CALLBACKS == 1)
hadc->ErrorCallback(hadc);
#else
HAL_ADC_ErrorCallback(hadc);
#endif /* USE_HAL_ADC_REGISTER_CALLBACKS */
}
/**
* @brief Delay micro seconds
* @param microSecond delay
* @retval None
*/
static void ADC_DelayMicroSecond(uint32_t microSecond)
{
/* Compute number of CPU cycles to wait for */
__IO uint32_t waitLoopIndex = (microSecond * (SystemCoreClock / 1000000U));
while(waitLoopIndex != 0U)
{
waitLoopIndex--;
}
}
/**
* @}
*/
#endif /* HAL_ADC_MODULE_ENABLED */
/**
* @}
*/
/**
* @}
*/
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/