| /** |
| ****************************************************************************** |
| * @file stm32l0xx_hal_rcc_ex.c |
| * @author MCD Application Team |
| * @brief Extended RCC HAL module driver. |
| * This file provides firmware functions to manage the following |
| * functionalities RCC extension peripheral: |
| * + Extended Peripheral Control functions |
| * + Extended Clock Recovery System Control functions |
| * |
| ****************************************************************************** |
| * @attention |
| * |
| * Copyright (c) 2016 STMicroelectronics. |
| * All rights reserved. |
| * |
| * This software is licensed under terms that can be found in the LICENSE file in |
| * the root directory of this software component. |
| * If no LICENSE file comes with this software, it is provided AS-IS. |
| ****************************************************************************** |
| */ |
| |
| /* Includes ------------------------------------------------------------------*/ |
| #include "stm32l0xx_hal.h" |
| |
| /** @addtogroup STM32L0xx_HAL_Driver |
| * @{ |
| */ |
| |
| #ifdef HAL_RCC_MODULE_ENABLED |
| |
| /** @defgroup RCCEx RCCEx |
| * @brief RCC Extension HAL module driver |
| * @{ |
| */ |
| |
| /* Private typedef -----------------------------------------------------------*/ |
| /* Private define ------------------------------------------------------------*/ |
| /** @defgroup RCCEx_Private_Constants RCCEx Private Constants |
| * @{ |
| */ |
| #if defined(USB) |
| extern const uint8_t PLLMulTable[]; |
| #endif /* USB */ |
| /** |
| * @} |
| */ |
| |
| /* Private macro -------------------------------------------------------------*/ |
| /** @defgroup RCCEx_Private_Macros RCCEx Private Macros |
| * @{ |
| */ |
| /** |
| * @} |
| */ |
| |
| /* Private variables ---------------------------------------------------------*/ |
| /* Private function prototypes -----------------------------------------------*/ |
| /* Private functions ---------------------------------------------------------*/ |
| |
| /** @defgroup RCCEx_Exported_Functions RCCEx Exported Functions |
| * @{ |
| */ |
| |
| /** @defgroup RCCEx_Exported_Functions_Group1 Extended Peripheral Control functions |
| * @brief Extended Peripheral Control functions |
| * |
| @verbatim |
| =============================================================================== |
| ##### Extended Peripheral Control functions ##### |
| =============================================================================== |
| [..] |
| This subsection provides a set of functions allowing to control the RCC Clocks |
| frequencies. |
| [..] |
| (@) Important note: Care must be taken when HAL_RCCEx_PeriphCLKConfig() is used to |
| select the RTC clock source; in this case the Backup domain will be reset in |
| order to modify the RTC Clock source, as consequence RTC registers (including |
| the backup registers) are set to their reset values. |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief Initializes the RCC extended peripherals clocks according to the specified |
| * parameters in the RCC_PeriphCLKInitTypeDef. |
| * @param PeriphClkInit pointer to an RCC_PeriphCLKInitTypeDef structure that |
| * contains the configuration information for the Extended Peripherals clocks(USART1,USART2, LPUART1, |
| * I2C1, I2C3, RTC, USB/RNG and LPTIM1 clocks). |
| * @retval HAL status |
| * @note If HAL_ERROR returned, first switch-OFF HSE clock oscillator with @ref HAL_RCC_OscConfig() |
| * to possibly update HSE divider. |
| */ |
| HAL_StatusTypeDef HAL_RCCEx_PeriphCLKConfig(RCC_PeriphCLKInitTypeDef *PeriphClkInit) |
| { |
| uint32_t tickstart; |
| uint32_t temp_reg; |
| FlagStatus pwrclkchanged = RESET; |
| |
| /* Check the parameters */ |
| assert_param(IS_RCC_PERIPHCLOCK(PeriphClkInit->PeriphClockSelection)); |
| |
| /*------------------------------- RTC/LCD Configuration ------------------------*/ |
| if ((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_RTC) == RCC_PERIPHCLK_RTC) |
| #if defined(LCD) |
| || (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_LCD) == RCC_PERIPHCLK_LCD) |
| #endif /* LCD */ |
| ) |
| { |
| /* check for RTC Parameters used to output RTCCLK */ |
| if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_RTC) == RCC_PERIPHCLK_RTC) |
| { |
| assert_param(IS_RCC_RTCCLKSOURCE(PeriphClkInit->RTCClockSelection)); |
| } |
| |
| #if defined(LCD) |
| if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_LCD) == RCC_PERIPHCLK_LCD) |
| { |
| assert_param(IS_RCC_RTCCLKSOURCE(PeriphClkInit->LCDClockSelection)); |
| } |
| #endif /* LCD */ |
| |
| /* As soon as function is called to change RTC clock source, activation of the |
| power domain is done. */ |
| /* Requires to enable write access to Backup Domain of necessary */ |
| if(__HAL_RCC_PWR_IS_CLK_DISABLED()) |
| { |
| __HAL_RCC_PWR_CLK_ENABLE(); |
| pwrclkchanged = SET; |
| } |
| |
| if(HAL_IS_BIT_CLR(PWR->CR, PWR_CR_DBP)) |
| { |
| /* Enable write access to Backup domain */ |
| SET_BIT(PWR->CR, PWR_CR_DBP); |
| |
| /* Wait for Backup domain Write protection disable */ |
| tickstart = HAL_GetTick(); |
| |
| while(HAL_IS_BIT_CLR(PWR->CR, PWR_CR_DBP)) |
| { |
| if((HAL_GetTick() - tickstart) > RCC_DBP_TIMEOUT_VALUE) |
| { |
| return HAL_TIMEOUT; |
| } |
| } |
| } |
| |
| /* Check if user wants to change HSE RTC prescaler whereas HSE is enabled */ |
| temp_reg = (RCC->CR & RCC_CR_RTCPRE); |
| if ((temp_reg != (PeriphClkInit->RTCClockSelection & RCC_CR_RTCPRE)) |
| #if defined (LCD) |
| || (temp_reg != (PeriphClkInit->LCDClockSelection & RCC_CR_RTCPRE)) |
| #endif /* LCD */ |
| ) |
| { /* Check HSE State */ |
| if ((PeriphClkInit->RTCClockSelection & RCC_CSR_RTCSEL) == RCC_CSR_RTCSEL_HSE) |
| { |
| if (HAL_IS_BIT_SET(RCC->CR, RCC_CR_HSERDY)) |
| { |
| /* To update HSE divider, first switch-OFF HSE clock oscillator*/ |
| return HAL_ERROR; |
| } |
| } |
| } |
| |
| /* Reset the Backup domain only if the RTC Clock source selection is modified from reset value */ |
| temp_reg = (RCC->CSR & RCC_CSR_RTCSEL); |
| |
| if((temp_reg != 0x00000000U) && (((temp_reg != (PeriphClkInit->RTCClockSelection & RCC_CSR_RTCSEL)) \ |
| && (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_RTC) == RCC_PERIPHCLK_RTC)) |
| #if defined(LCD) |
| || ((temp_reg != (PeriphClkInit->LCDClockSelection & RCC_CSR_RTCSEL)) \ |
| && (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_LCD) == RCC_PERIPHCLK_LCD)) |
| #endif /* LCD */ |
| )) |
| { |
| /* Store the content of CSR register before the reset of Backup Domain */ |
| temp_reg = (RCC->CSR & ~(RCC_CSR_RTCSEL)); |
| |
| /* RTC Clock selection can be changed only if the Backup Domain is reset */ |
| __HAL_RCC_BACKUPRESET_FORCE(); |
| __HAL_RCC_BACKUPRESET_RELEASE(); |
| |
| /* Restore the Content of CSR register */ |
| RCC->CSR = temp_reg; |
| |
| /* Wait for LSERDY if LSE was enabled */ |
| if (HAL_IS_BIT_SET(temp_reg, RCC_CSR_LSEON)) |
| { |
| /* Get Start Tick */ |
| tickstart = HAL_GetTick(); |
| |
| /* Wait till LSE is ready */ |
| while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == 0U) |
| { |
| if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) |
| { |
| return HAL_TIMEOUT; |
| } |
| } |
| } |
| } |
| #if defined(LCD) |
| if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_LCD) == RCC_PERIPHCLK_LCD) |
| { |
| __HAL_RCC_LCD_CONFIG(PeriphClkInit->LCDClockSelection); |
| } |
| #endif /* LCD */ |
| |
| if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_RTC) == RCC_PERIPHCLK_RTC) |
| { |
| __HAL_RCC_RTC_CONFIG(PeriphClkInit->RTCClockSelection); |
| } |
| |
| /* Require to disable power clock if necessary */ |
| if(pwrclkchanged == SET) |
| { |
| __HAL_RCC_PWR_CLK_DISABLE(); |
| } |
| } |
| |
| #if defined (RCC_CCIPR_USART1SEL) |
| /*------------------------------- USART1 Configuration ------------------------*/ |
| if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_USART1) == RCC_PERIPHCLK_USART1) |
| { |
| /* Check the parameters */ |
| assert_param(IS_RCC_USART1CLKSOURCE(PeriphClkInit->Usart1ClockSelection)); |
| |
| /* Configure the USART1 clock source */ |
| __HAL_RCC_USART1_CONFIG(PeriphClkInit->Usart1ClockSelection); |
| } |
| #endif /* RCC_CCIPR_USART1SEL */ |
| |
| /*----------------------------- USART2 Configuration --------------------------*/ |
| if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_USART2) == RCC_PERIPHCLK_USART2) |
| { |
| /* Check the parameters */ |
| assert_param(IS_RCC_USART2CLKSOURCE(PeriphClkInit->Usart2ClockSelection)); |
| |
| /* Configure the USART2 clock source */ |
| __HAL_RCC_USART2_CONFIG(PeriphClkInit->Usart2ClockSelection); |
| } |
| |
| /*------------------------------ LPUART1 Configuration ------------------------*/ |
| if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_LPUART1) == RCC_PERIPHCLK_LPUART1) |
| { |
| /* Check the parameters */ |
| assert_param(IS_RCC_LPUART1CLKSOURCE(PeriphClkInit->Lpuart1ClockSelection)); |
| |
| /* Configure the LPUAR1 clock source */ |
| __HAL_RCC_LPUART1_CONFIG(PeriphClkInit->Lpuart1ClockSelection); |
| } |
| |
| /*------------------------------ I2C1 Configuration ------------------------*/ |
| if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2C1) == RCC_PERIPHCLK_I2C1) |
| { |
| /* Check the parameters */ |
| assert_param(IS_RCC_I2C1CLKSOURCE(PeriphClkInit->I2c1ClockSelection)); |
| |
| /* Configure the I2C1 clock source */ |
| __HAL_RCC_I2C1_CONFIG(PeriphClkInit->I2c1ClockSelection); |
| } |
| |
| #if defined (RCC_CCIPR_I2C3SEL) |
| /*------------------------------ I2C3 Configuration ------------------------*/ |
| if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2C3) == RCC_PERIPHCLK_I2C3) |
| { |
| /* Check the parameters */ |
| assert_param(IS_RCC_I2C3CLKSOURCE(PeriphClkInit->I2c3ClockSelection)); |
| |
| /* Configure the I2C3 clock source */ |
| __HAL_RCC_I2C3_CONFIG(PeriphClkInit->I2c3ClockSelection); |
| } |
| #endif /* RCC_CCIPR_I2C3SEL */ |
| |
| #if defined(USB) |
| /*---------------------------- USB and RNG configuration --------------------*/ |
| if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_USB) == (RCC_PERIPHCLK_USB)) |
| { |
| assert_param(IS_RCC_USBCLKSOURCE(PeriphClkInit->UsbClockSelection)); |
| __HAL_RCC_USB_CONFIG(PeriphClkInit->UsbClockSelection); |
| } |
| #endif /* USB */ |
| |
| /*---------------------------- LPTIM1 configuration ------------------------*/ |
| if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_LPTIM1) == (RCC_PERIPHCLK_LPTIM1)) |
| { |
| assert_param(IS_RCC_LPTIMCLK(PeriphClkInit->LptimClockSelection)); |
| __HAL_RCC_LPTIM1_CONFIG(PeriphClkInit->LptimClockSelection); |
| } |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Get the PeriphClkInit according to the internal RCC configuration registers. |
| * @param PeriphClkInit pointer to an RCC_PeriphCLKInitTypeDef structure that |
| * returns the configuration information for the Extended Peripherals clocks(USART1,USART2, LPUART1, |
| * I2C1, I2C3, RTC, USB/RNG and LPTIM1 clocks). |
| * @retval None |
| */ |
| void HAL_RCCEx_GetPeriphCLKConfig(RCC_PeriphCLKInitTypeDef *PeriphClkInit) |
| { |
| uint32_t srcclk; |
| |
| /* Set all possible values for the extended clock type parameter -----------*/ |
| /* Common part first */ |
| PeriphClkInit->PeriphClockSelection = RCC_PERIPHCLK_USART2 | RCC_PERIPHCLK_LPUART1 | \ |
| RCC_PERIPHCLK_I2C1 | RCC_PERIPHCLK_RTC | \ |
| RCC_PERIPHCLK_LPTIM1; |
| #if defined(RCC_CCIPR_USART1SEL) |
| PeriphClkInit->PeriphClockSelection |= RCC_PERIPHCLK_USART1; |
| #endif /* RCC_CCIPR_USART1SEL */ |
| #if defined(RCC_CCIPR_I2C3SEL) |
| PeriphClkInit->PeriphClockSelection |= RCC_PERIPHCLK_I2C3; |
| #endif /* RCC_CCIPR_I2C3SEL */ |
| #if defined(USB) |
| PeriphClkInit->PeriphClockSelection |= RCC_PERIPHCLK_USB; |
| #endif /* USB */ |
| #if defined(LCD) |
| PeriphClkInit->PeriphClockSelection |= RCC_PERIPHCLK_LCD; |
| #endif /* LCD */ |
| |
| /* Get the RTC/LCD configuration -----------------------------------------------*/ |
| srcclk = __HAL_RCC_GET_RTC_SOURCE(); |
| if (srcclk != RCC_RTCCLKSOURCE_HSE_DIV2) |
| { |
| /* Source clock is LSE or LSI*/ |
| PeriphClkInit->RTCClockSelection = srcclk; |
| } |
| else |
| { |
| /* Source clock is HSE. Need to get the prescaler value*/ |
| PeriphClkInit->RTCClockSelection = srcclk | (READ_BIT(RCC->CR, RCC_CR_RTCPRE)); |
| } |
| #if defined(LCD) |
| PeriphClkInit->LCDClockSelection = PeriphClkInit->RTCClockSelection; |
| #endif /* LCD */ |
| #if defined(RCC_CCIPR_USART1SEL) |
| /* Get the USART1 configuration --------------------------------------------*/ |
| PeriphClkInit->Usart1ClockSelection = __HAL_RCC_GET_USART1_SOURCE(); |
| #endif /* RCC_CCIPR_USART1SEL */ |
| /* Get the USART2 clock source ---------------------------------------------*/ |
| PeriphClkInit->Usart2ClockSelection = __HAL_RCC_GET_USART2_SOURCE(); |
| /* Get the LPUART1 clock source ---------------------------------------------*/ |
| PeriphClkInit->Lpuart1ClockSelection = __HAL_RCC_GET_LPUART1_SOURCE(); |
| /* Get the I2C1 clock source -----------------------------------------------*/ |
| PeriphClkInit->I2c1ClockSelection = __HAL_RCC_GET_I2C1_SOURCE(); |
| #if defined(RCC_CCIPR_I2C3SEL) |
| /* Get the I2C3 clock source -----------------------------------------------*/ |
| PeriphClkInit->I2c3ClockSelection = __HAL_RCC_GET_I2C3_SOURCE(); |
| #endif /* RCC_CCIPR_I2C3SEL */ |
| /* Get the LPTIM1 clock source -----------------------------------------------*/ |
| PeriphClkInit->LptimClockSelection = __HAL_RCC_GET_LPTIM1_SOURCE(); |
| /* Get the RTC clock source -----------------------------------------------*/ |
| PeriphClkInit->RTCClockSelection = __HAL_RCC_GET_RTC_SOURCE(); |
| #if defined(USB) |
| /* Get the USB/RNG clock source -----------------------------------------------*/ |
| PeriphClkInit->UsbClockSelection = __HAL_RCC_GET_USB_SOURCE(); |
| #endif /* USB */ |
| } |
| |
| /** |
| * @brief Return the peripheral clock frequency |
| * @note Return 0 if peripheral clock is unknown |
| * @param PeriphClk Peripheral clock identifier |
| * This parameter can be one of the following values: |
| * @arg @ref RCC_PERIPHCLK_RTC RTC peripheral clock |
| * @arg @ref RCC_PERIPHCLK_LCD LCD peripheral clock (*) |
| * @arg @ref RCC_PERIPHCLK_USB USB or RNG peripheral clock (*) |
| * @arg @ref RCC_PERIPHCLK_USART1 USART1 peripheral clock (*) |
| * @arg @ref RCC_PERIPHCLK_USART2 USART2 peripheral clock |
| * @arg @ref RCC_PERIPHCLK_LPUART1 LPUART1 peripheral clock |
| * @arg @ref RCC_PERIPHCLK_I2C1 I2C1 peripheral clock |
| * @arg @ref RCC_PERIPHCLK_I2C2 I2C2 peripheral clock (*) |
| * @arg @ref RCC_PERIPHCLK_I2C3 I2C3 peripheral clock (*) |
| * @note (*) means that this peripheral is not present on all the devices |
| * @retval Frequency in Hz (0: means that no available frequency for the peripheral) |
| */ |
| uint32_t HAL_RCCEx_GetPeriphCLKFreq(uint32_t PeriphClk) |
| { |
| uint32_t frequency = 0U; |
| uint32_t temp_reg, clkprediv, srcclk; /* no init needed */ |
| #if defined(USB) |
| uint32_t pllmul, plldiv, pllvco; /* no init needed */ |
| #endif /* USB */ |
| |
| /* Check the parameters */ |
| assert_param(IS_RCC_PERIPHCLOCK(PeriphClk)); |
| |
| switch (PeriphClk) |
| { |
| case RCC_PERIPHCLK_RTC: |
| #if defined(LCD) |
| case RCC_PERIPHCLK_LCD: |
| #endif /* LCD */ |
| { |
| /* Get RCC CSR configuration ------------------------------------------------------*/ |
| temp_reg = RCC->CSR; |
| |
| /* Get the current RTC source */ |
| srcclk = __HAL_RCC_GET_RTC_SOURCE(); |
| |
| /* Check if LSE is ready if RTC clock selection is LSE */ |
| if ((srcclk == RCC_RTCCLKSOURCE_LSE) && (HAL_IS_BIT_SET(temp_reg, RCC_CSR_LSERDY))) |
| { |
| frequency = LSE_VALUE; |
| } |
| /* Check if LSI is ready if RTC clock selection is LSI */ |
| else if (srcclk == RCC_RTCCLKSOURCE_LSI) |
| { |
| if (HAL_IS_BIT_SET(temp_reg, RCC_CSR_LSIRDY)) |
| { |
| frequency = LSI_VALUE; |
| } |
| } |
| /* Check if HSE is ready and if RTC clock selection is HSE */ |
| else if (srcclk == RCC_RTCCLKSOURCE_HSE_DIVX) |
| { |
| if (HAL_IS_BIT_SET(RCC->CR, RCC_CR_HSERDY)) |
| { |
| /* Get the current HSE clock divider */ |
| clkprediv = __HAL_RCC_GET_RTC_HSE_PRESCALER(); |
| |
| switch (clkprediv) |
| { |
| case RCC_RTC_HSE_DIV_16: /* HSE DIV16 has been selected */ |
| { |
| frequency = HSE_VALUE / 16U; |
| break; |
| } |
| case RCC_RTC_HSE_DIV_8: /* HSE DIV8 has been selected */ |
| { |
| frequency = HSE_VALUE / 8U; |
| break; |
| } |
| case RCC_RTC_HSE_DIV_4: /* HSE DIV4 has been selected */ |
| { |
| frequency = HSE_VALUE / 4U; |
| break; |
| } |
| default: /* HSE DIV2 has been selected */ |
| { |
| frequency = HSE_VALUE / 2U; |
| break; |
| } |
| } |
| } |
| } |
| /* Clock not enabled for RTC */ |
| else |
| { |
| /* nothing to do: frequency already initialized to 0U */ |
| } |
| break; |
| } |
| #if defined(USB) |
| case RCC_PERIPHCLK_USB: |
| { |
| /* Get the current USB source */ |
| srcclk = __HAL_RCC_GET_USB_SOURCE(); |
| |
| if (srcclk == RCC_USBCLKSOURCE_PLL) |
| { |
| if (HAL_IS_BIT_SET(RCC->CR, RCC_CR_PLLRDY)) |
| { |
| /* Get PLL clock source and multiplication factor ----------------------*/ |
| pllmul = RCC->CFGR & RCC_CFGR_PLLMUL; |
| plldiv = RCC->CFGR & RCC_CFGR_PLLDIV; |
| pllmul = PLLMulTable[(pllmul >> RCC_CFGR_PLLMUL_Pos)]; |
| plldiv = (plldiv >> RCC_CFGR_PLLDIV_Pos) + 1U; |
| |
| /* Compute PLL clock input */ |
| if(__HAL_RCC_GET_PLL_OSCSOURCE() == RCC_PLLSOURCE_HSI) |
| { |
| if (READ_BIT(RCC->CR, RCC_CR_HSIDIVF) != 0U) |
| { |
| pllvco = (HSI_VALUE >> 2U); |
| } |
| else |
| { |
| pllvco = HSI_VALUE; |
| } |
| } |
| else /* HSE source */ |
| { |
| pllvco = HSE_VALUE; |
| } |
| /* pllvco * pllmul / plldiv */ |
| pllvco = (pllvco * pllmul); |
| frequency = (pllvco/ plldiv); |
| } |
| } |
| else if (srcclk == RCC_USBCLKSOURCE_HSI48) |
| { |
| if (HAL_IS_BIT_SET(RCC->CRRCR, RCC_CRRCR_HSI48RDY)) |
| { |
| frequency = HSI48_VALUE; |
| } |
| } |
| else /* RCC_USBCLKSOURCE_NONE */ |
| { |
| /* nothing to do: frequency already initialized to 0U */ |
| } |
| break; |
| } |
| #endif /* USB */ |
| #if defined(RCC_CCIPR_USART1SEL) |
| case RCC_PERIPHCLK_USART1: |
| { |
| /* Get the current USART1 source */ |
| srcclk = __HAL_RCC_GET_USART1_SOURCE(); |
| |
| /* Check if USART1 clock selection is PCLK2 */ |
| if (srcclk == RCC_USART1CLKSOURCE_PCLK2) |
| { |
| frequency = HAL_RCC_GetPCLK2Freq(); |
| } |
| /* Check if HSI is ready and if USART1 clock selection is HSI */ |
| else if (srcclk == RCC_USART1CLKSOURCE_HSI) |
| { |
| if (HAL_IS_BIT_SET(RCC->CR, RCC_CR_HSIRDY)) |
| { |
| if (READ_BIT(RCC->CR, RCC_CR_HSIDIVF) != 0U) |
| { |
| frequency = (HSI_VALUE >> 2U); |
| } |
| else |
| { |
| frequency = HSI_VALUE; |
| } |
| } |
| } |
| /* Check if USART1 clock selection is SYSCLK */ |
| else if (srcclk == RCC_USART1CLKSOURCE_SYSCLK) |
| { |
| frequency = HAL_RCC_GetSysClockFreq(); |
| } |
| /* Check if LSE is ready and if USART1 clock selection is LSE */ |
| else if (srcclk == RCC_USART1CLKSOURCE_LSE) |
| { |
| if (HAL_IS_BIT_SET(RCC->CSR, RCC_CSR_LSERDY)) |
| { |
| frequency = LSE_VALUE; |
| } |
| } |
| /* Clock not enabled for USART1*/ |
| else |
| { |
| /* nothing to do: frequency already initialized to 0U */ |
| } |
| break; |
| } |
| #endif /* RCC_CCIPR_USART1SEL */ |
| case RCC_PERIPHCLK_USART2: |
| { |
| /* Get the current USART2 source */ |
| srcclk = __HAL_RCC_GET_USART2_SOURCE(); |
| |
| /* Check if USART2 clock selection is PCLK1 */ |
| if (srcclk == RCC_USART2CLKSOURCE_PCLK1) |
| { |
| frequency = HAL_RCC_GetPCLK1Freq(); |
| } |
| /* Check if HSI is ready and if USART2 clock selection is HSI */ |
| else if (srcclk == RCC_USART2CLKSOURCE_HSI) |
| { |
| if (HAL_IS_BIT_SET(RCC->CR, RCC_CR_HSIRDY)) |
| { |
| if (READ_BIT(RCC->CR, RCC_CR_HSIDIVF) != 0U) |
| { |
| frequency = (HSI_VALUE >> 2U); |
| } |
| else |
| { |
| frequency = HSI_VALUE; |
| } |
| } |
| } |
| /* Check if USART2 clock selection is SYSCLK */ |
| else if (srcclk == RCC_USART2CLKSOURCE_SYSCLK) |
| { |
| frequency = HAL_RCC_GetSysClockFreq(); |
| } |
| /* Check if LSE is ready and if USART2 clock selection is LSE */ |
| else if (srcclk == RCC_USART2CLKSOURCE_LSE) |
| { |
| if (HAL_IS_BIT_SET(RCC->CSR, RCC_CSR_LSERDY)) |
| { |
| frequency = LSE_VALUE; |
| } |
| } |
| /* Clock not enabled for USART2*/ |
| else |
| { |
| /* nothing to do: frequency already initialized to 0U */ |
| } |
| break; |
| } |
| case RCC_PERIPHCLK_LPUART1: |
| { |
| /* Get the current LPUART1 source */ |
| srcclk = __HAL_RCC_GET_LPUART1_SOURCE(); |
| |
| /* Check if LPUART1 clock selection is PCLK1 */ |
| if (srcclk == RCC_LPUART1CLKSOURCE_PCLK1) |
| { |
| frequency = HAL_RCC_GetPCLK1Freq(); |
| } |
| /* Check if HSI is ready and if LPUART1 clock selection is HSI */ |
| else if (srcclk == RCC_LPUART1CLKSOURCE_HSI) |
| { |
| if (HAL_IS_BIT_SET(RCC->CR, RCC_CR_HSIRDY)) |
| { |
| if (READ_BIT(RCC->CR, RCC_CR_HSIDIVF) != 0U) |
| { |
| frequency = (HSI_VALUE >> 2U); |
| } |
| else |
| { |
| frequency = HSI_VALUE; |
| } |
| } |
| } |
| /* Check if LPUART1 clock selection is SYSCLK */ |
| else if (srcclk == RCC_LPUART1CLKSOURCE_SYSCLK) |
| { |
| frequency = HAL_RCC_GetSysClockFreq(); |
| } |
| /* Check if LSE is ready and if LPUART1 clock selection is LSE */ |
| else if (srcclk == RCC_LPUART1CLKSOURCE_LSE) |
| { |
| if (HAL_IS_BIT_SET(RCC->CSR, RCC_CSR_LSERDY)) |
| { |
| frequency = LSE_VALUE; |
| } |
| } |
| /* Clock not enabled for LPUART1*/ |
| else |
| { |
| /* nothing to do: frequency already initialized to 0U */ |
| } |
| break; |
| } |
| case RCC_PERIPHCLK_I2C1: |
| { |
| /* Get the current I2C1 source */ |
| srcclk = __HAL_RCC_GET_I2C1_SOURCE(); |
| |
| /* Check if I2C1 clock selection is PCLK1 */ |
| if (srcclk == RCC_I2C1CLKSOURCE_PCLK1) |
| { |
| frequency = HAL_RCC_GetPCLK1Freq(); |
| } |
| /* Check if HSI is ready and if I2C1 clock selection is HSI */ |
| else if (srcclk == RCC_I2C1CLKSOURCE_HSI) |
| { |
| if (HAL_IS_BIT_SET(RCC->CR, RCC_CR_HSIRDY)) |
| { |
| if (READ_BIT(RCC->CR, RCC_CR_HSIDIVF) != 0U) |
| { |
| frequency = (HSI_VALUE >> 2U); |
| } |
| else |
| { |
| frequency = HSI_VALUE; |
| } |
| } |
| } |
| /* Check if I2C1 clock selection is SYSCLK */ |
| else if (srcclk == RCC_I2C1CLKSOURCE_SYSCLK) |
| { |
| frequency = HAL_RCC_GetSysClockFreq(); |
| } |
| /* Clock not enabled for I2C1*/ |
| else |
| { |
| /* nothing to do: frequency already initialized to 0U */ |
| } |
| break; |
| } |
| #if defined(I2C2) |
| case RCC_PERIPHCLK_I2C2: |
| { |
| |
| /* Check if I2C2 on APB1 clock enabled*/ |
| if (READ_BIT(RCC->APB1ENR, (RCC_APB1ENR_I2C2EN))==RCC_APB1ENR_I2C2EN) |
| { |
| frequency = HAL_RCC_GetPCLK1Freq(); |
| } |
| else |
| { |
| /* nothing to do: frequency already initialized to 0U */ |
| } |
| break; |
| } |
| #endif /* I2C2 */ |
| |
| #if defined(RCC_CCIPR_I2C3SEL) |
| case RCC_PERIPHCLK_I2C3: |
| { |
| /* Get the current I2C3 source */ |
| srcclk = __HAL_RCC_GET_I2C3_SOURCE(); |
| |
| /* Check if I2C3 clock selection is PCLK1 */ |
| if (srcclk == RCC_I2C3CLKSOURCE_PCLK1) |
| { |
| frequency = HAL_RCC_GetPCLK1Freq(); |
| } |
| /* Check if HSI is ready and if I2C3 clock selection is HSI */ |
| else if (srcclk == RCC_I2C3CLKSOURCE_HSI) |
| { |
| if (HAL_IS_BIT_SET(RCC->CR, RCC_CR_HSIRDY)) |
| { |
| if (READ_BIT(RCC->CR, RCC_CR_HSIDIVF) != 0U) |
| { |
| frequency = (HSI_VALUE >> 2U); |
| } |
| else |
| { |
| frequency = HSI_VALUE; |
| } |
| } |
| } |
| /* Check if I2C3 clock selection is SYSCLK */ |
| else if (srcclk == RCC_I2C3CLKSOURCE_SYSCLK) |
| { |
| frequency = HAL_RCC_GetSysClockFreq(); |
| } |
| /* Clock not enabled for I2C3*/ |
| else |
| { |
| /* nothing to do: frequency already initialized to 0U */ |
| } |
| break; |
| } |
| #endif /* RCC_CCIPR_I2C3SEL */ |
| default: |
| { |
| break; |
| } |
| } |
| return(frequency); |
| } |
| |
| /** |
| * @brief Enables the LSE Clock Security System. |
| * @retval None |
| */ |
| void HAL_RCCEx_EnableLSECSS(void) |
| { |
| SET_BIT(RCC->CSR, RCC_CSR_LSECSSON) ; |
| } |
| |
| /** |
| * @brief Disables the LSE Clock Security System. |
| * @note Once enabled this bit cannot be disabled, except after an LSE failure detection |
| * (LSECSSD=1). In that case the software MUST disable the LSECSSON bit. |
| * Reset by power on reset and RTC software reset (RTCRST bit). |
| * @retval None |
| */ |
| void HAL_RCCEx_DisableLSECSS(void) |
| { |
| /* Disable LSE CSS */ |
| CLEAR_BIT(RCC->CSR, RCC_CSR_LSECSSON) ; |
| |
| /* Disable LSE CSS IT */ |
| __HAL_RCC_DISABLE_IT(RCC_IT_LSECSS); |
| } |
| |
| /** |
| * @brief Enable the LSE Clock Security System IT & corresponding EXTI line. |
| * @note LSE Clock Security System IT is mapped on RTC EXTI line 19 |
| * @retval None |
| */ |
| void HAL_RCCEx_EnableLSECSS_IT(void) |
| { |
| /* Enable LSE CSS */ |
| SET_BIT(RCC->CSR, RCC_CSR_LSECSSON) ; |
| |
| /* Enable LSE CSS IT */ |
| __HAL_RCC_ENABLE_IT(RCC_IT_LSECSS); |
| |
| /* Enable IT on EXTI Line 19 */ |
| __HAL_RCC_LSECSS_EXTI_ENABLE_IT(); |
| __HAL_RCC_LSECSS_EXTI_ENABLE_RISING_EDGE(); |
| } |
| |
| /** |
| * @brief Handle the RCC LSE Clock Security System interrupt request. |
| * @retval None |
| */ |
| void HAL_RCCEx_LSECSS_IRQHandler(void) |
| { |
| /* Check RCC LSE CSSF flag */ |
| if(__HAL_RCC_GET_IT(RCC_IT_LSECSS)) |
| { |
| /* RCC LSE Clock Security System interrupt user callback */ |
| HAL_RCCEx_LSECSS_Callback(); |
| |
| /* Clear RCC LSE CSS pending bit */ |
| __HAL_RCC_CLEAR_IT(RCC_IT_LSECSS); |
| } |
| } |
| |
| /** |
| * @brief RCCEx LSE Clock Security System interrupt callback. |
| * @retval none |
| */ |
| __weak void HAL_RCCEx_LSECSS_Callback(void) |
| { |
| /* NOTE : This function should not be modified, when the callback is needed, |
| the @ref HAL_RCCEx_LSECSS_Callback should be implemented in the user file |
| */ |
| } |
| |
| #if defined(SYSCFG_CFGR3_ENREF_HSI48) |
| /** |
| * @brief Enables Vrefint for the HSI48. |
| * @note This is functional only if the LOCK is not set |
| * @retval None |
| */ |
| void HAL_RCCEx_EnableHSI48_VREFINT(void) |
| { |
| /* Enable the Buffer for the ADC by setting SYSCFG_CFGR3_ENREF_HSI48 bit in SYSCFG_CFGR3 register */ |
| SET_BIT (SYSCFG->CFGR3, SYSCFG_CFGR3_ENREF_HSI48); |
| } |
| |
| /** |
| * @brief Disables the Vrefint for the HSI48. |
| * @note This is functional only if the LOCK is not set |
| * @retval None |
| */ |
| void HAL_RCCEx_DisableHSI48_VREFINT(void) |
| { |
| /* Disable the Vrefint by resetting SYSCFG_CFGR3_ENREF_HSI48 bit in SYSCFG_CFGR3 register */ |
| CLEAR_BIT(SYSCFG->CFGR3, SYSCFG_CFGR3_ENREF_HSI48); |
| } |
| |
| #endif /* SYSCFG_CFGR3_ENREF_HSI48 */ |
| |
| /** |
| * @} |
| */ |
| |
| #if defined (CRS) |
| |
| /** @defgroup RCCEx_Exported_Functions_Group3 Extended Clock Recovery System Control functions |
| * @brief Extended Clock Recovery System Control functions |
| * |
| @verbatim |
| =============================================================================== |
| ##### Extended Clock Recovery System Control functions ##### |
| =============================================================================== |
| [..] |
| For devices with Clock Recovery System feature (CRS), RCC Extension HAL driver can be used as follows: |
| |
| (#) In System clock config, HSI48 needs to be enabled |
| |
| (#) Enable CRS clock in IP MSP init which will use CRS functions |
| |
| (#) Call CRS functions as follows: |
| (##) Prepare synchronization configuration necessary for HSI48 calibration |
| (+++) Default values can be set for frequency Error Measurement (reload and error limit) |
| and also HSI48 oscillator smooth trimming. |
| (+++) Macro __HAL_RCC_CRS_RELOADVALUE_CALCULATE can be also used to calculate |
| directly reload value with target and synchronization frequencies values |
| (##) Call function HAL_RCCEx_CRSConfig which |
| (+++) Reset CRS registers to their default values. |
| (+++) Configure CRS registers with synchronization configuration |
| (+++) Enable automatic calibration and frequency error counter feature |
| Note: When using USB LPM (Link Power Management) and the device is in Sleep mode, the |
| periodic USB SOF will not be generated by the host. No SYNC signal will therefore be |
| provided to the CRS to calibrate the HSI48 on the run. To guarantee the required clock |
| precision after waking up from Sleep mode, the LSE or reference clock on the GPIOs |
| should be used as SYNC signal. |
| |
| (##) A polling function is provided to wait for complete synchronization |
| (+++) Call function HAL_RCCEx_CRSWaitSynchronization() |
| (+++) According to CRS status, user can decide to adjust again the calibration or continue |
| application if synchronization is OK |
| |
| (#) User can retrieve information related to synchronization in calling function |
| HAL_RCCEx_CRSGetSynchronizationInfo() |
| |
| (#) Regarding synchronization status and synchronization information, user can try a new calibration |
| in changing synchronization configuration and call again HAL_RCCEx_CRSConfig. |
| Note: When the SYNC event is detected during the downcounting phase (before reaching the zero value), |
| it means that the actual frequency is lower than the target (and so, that the TRIM value should be |
| incremented), while when it is detected during the upcounting phase it means that the actual frequency |
| is higher (and that the TRIM value should be decremented). |
| |
| (#) In interrupt mode, user can resort to the available macros (__HAL_RCC_CRS_XXX_IT). Interrupts will go |
| through CRS Handler (RCC_IRQn/RCC_IRQHandler) |
| (++) Call function HAL_RCCEx_CRSConfig() |
| (++) Enable RCC_IRQn (thanks to NVIC functions) |
| (++) Enable CRS interrupt (__HAL_RCC_CRS_ENABLE_IT) |
| (++) Implement CRS status management in the following user callbacks called from |
| HAL_RCCEx_CRS_IRQHandler(): |
| (+++) HAL_RCCEx_CRS_SyncOkCallback() |
| (+++) HAL_RCCEx_CRS_SyncWarnCallback() |
| (+++) HAL_RCCEx_CRS_ExpectedSyncCallback() |
| (+++) HAL_RCCEx_CRS_ErrorCallback() |
| |
| (#) To force a SYNC EVENT, user can use the function HAL_RCCEx_CRSSoftwareSynchronizationGenerate(). |
| This function can be called before calling HAL_RCCEx_CRSConfig (for instance in Systick handler) |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief Start automatic synchronization for polling mode |
| * @param pInit Pointer on RCC_CRSInitTypeDef structure |
| * @retval None |
| */ |
| void HAL_RCCEx_CRSConfig(RCC_CRSInitTypeDef *pInit) |
| { |
| uint32_t value; |
| |
| /* Check the parameters */ |
| assert_param(IS_RCC_CRS_SYNC_DIV(pInit->Prescaler)); |
| assert_param(IS_RCC_CRS_SYNC_SOURCE(pInit->Source)); |
| assert_param(IS_RCC_CRS_SYNC_POLARITY(pInit->Polarity)); |
| assert_param(IS_RCC_CRS_RELOADVALUE(pInit->ReloadValue)); |
| assert_param(IS_RCC_CRS_ERRORLIMIT(pInit->ErrorLimitValue)); |
| assert_param(IS_RCC_CRS_HSI48CALIBRATION(pInit->HSI48CalibrationValue)); |
| |
| /* CONFIGURATION */ |
| |
| /* Before configuration, reset CRS registers to their default values*/ |
| __HAL_RCC_CRS_FORCE_RESET(); |
| __HAL_RCC_CRS_RELEASE_RESET(); |
| |
| /* Set the SYNCDIV[2:0] bits according to Prescaler value */ |
| /* Set the SYNCSRC[1:0] bits according to Source value */ |
| /* Set the SYNCSPOL bit according to Polarity value */ |
| value = (pInit->Prescaler | pInit->Source | pInit->Polarity); |
| /* Set the RELOAD[15:0] bits according to ReloadValue value */ |
| value |= pInit->ReloadValue; |
| /* Set the FELIM[7:0] bits according to ErrorLimitValue value */ |
| value |= (pInit->ErrorLimitValue << CRS_CFGR_FELIM_Pos); |
| WRITE_REG(CRS->CFGR, value); |
| |
| /* Adjust HSI48 oscillator smooth trimming */ |
| /* Set the TRIM[5:0] bits according to RCC_CRS_HSI48CalibrationValue value */ |
| MODIFY_REG(CRS->CR, CRS_CR_TRIM, (pInit->HSI48CalibrationValue << CRS_CR_TRIM_Pos)); |
| |
| /* START AUTOMATIC SYNCHRONIZATION*/ |
| |
| /* Enable Automatic trimming & Frequency error counter */ |
| SET_BIT(CRS->CR, CRS_CR_AUTOTRIMEN | CRS_CR_CEN); |
| } |
| |
| /** |
| * @brief Generate the software synchronization event |
| * @retval None |
| */ |
| void HAL_RCCEx_CRSSoftwareSynchronizationGenerate(void) |
| { |
| SET_BIT(CRS->CR, CRS_CR_SWSYNC); |
| } |
| |
| /** |
| * @brief Return synchronization info |
| * @param pSynchroInfo Pointer on RCC_CRSSynchroInfoTypeDef structure |
| * @retval None |
| */ |
| void HAL_RCCEx_CRSGetSynchronizationInfo(RCC_CRSSynchroInfoTypeDef *pSynchroInfo) |
| { |
| /* Check the parameter */ |
| assert_param(pSynchroInfo != (void *)NULL); |
| |
| /* Get the reload value */ |
| pSynchroInfo->ReloadValue = (uint32_t)(READ_BIT(CRS->CFGR, CRS_CFGR_RELOAD)); |
| |
| /* Get HSI48 oscillator smooth trimming */ |
| pSynchroInfo->HSI48CalibrationValue = (uint32_t)(READ_BIT(CRS->CR, CRS_CR_TRIM) >> CRS_CR_TRIM_Pos); |
| |
| /* Get Frequency error capture */ |
| pSynchroInfo->FreqErrorCapture = (uint32_t)(READ_BIT(CRS->ISR, CRS_ISR_FECAP) >> CRS_ISR_FECAP_Pos); |
| |
| /* Get Frequency error direction */ |
| pSynchroInfo->FreqErrorDirection = (uint32_t)(READ_BIT(CRS->ISR, CRS_ISR_FEDIR)); |
| } |
| |
| /** |
| * @brief Wait for CRS Synchronization status. |
| * @param Timeout Duration of the timeout |
| * @note Timeout is based on the maximum time to receive a SYNC event based on synchronization |
| * frequency. |
| * @note If Timeout set to HAL_MAX_DELAY, HAL_TIMEOUT will be never returned. |
| * @retval Combination of Synchronization status |
| * This parameter can be a combination of the following values: |
| * @arg @ref RCC_CRS_TIMEOUT |
| * @arg @ref RCC_CRS_SYNCOK |
| * @arg @ref RCC_CRS_SYNCWARN |
| * @arg @ref RCC_CRS_SYNCERR |
| * @arg @ref RCC_CRS_SYNCMISS |
| * @arg @ref RCC_CRS_TRIMOVF |
| */ |
| uint32_t HAL_RCCEx_CRSWaitSynchronization(uint32_t Timeout) |
| { |
| uint32_t crsstatus = RCC_CRS_NONE; |
| uint32_t tickstart; |
| |
| /* Get timeout */ |
| tickstart = HAL_GetTick(); |
| |
| /* Wait for CRS flag or timeout detection */ |
| do |
| { |
| if(Timeout != HAL_MAX_DELAY) |
| { |
| if(((HAL_GetTick() - tickstart) > Timeout) || (Timeout == 0U)) |
| { |
| crsstatus = RCC_CRS_TIMEOUT; |
| } |
| } |
| /* Check CRS SYNCOK flag */ |
| if(__HAL_RCC_CRS_GET_FLAG(RCC_CRS_FLAG_SYNCOK)) |
| { |
| /* CRS SYNC event OK */ |
| crsstatus |= RCC_CRS_SYNCOK; |
| |
| /* Clear CRS SYNC event OK bit */ |
| __HAL_RCC_CRS_CLEAR_FLAG(RCC_CRS_FLAG_SYNCOK); |
| } |
| |
| /* Check CRS SYNCWARN flag */ |
| if(__HAL_RCC_CRS_GET_FLAG(RCC_CRS_FLAG_SYNCWARN)) |
| { |
| /* CRS SYNC warning */ |
| crsstatus |= RCC_CRS_SYNCWARN; |
| |
| /* Clear CRS SYNCWARN bit */ |
| __HAL_RCC_CRS_CLEAR_FLAG(RCC_CRS_FLAG_SYNCWARN); |
| } |
| |
| /* Check CRS TRIM overflow flag */ |
| if(__HAL_RCC_CRS_GET_FLAG(RCC_CRS_FLAG_TRIMOVF)) |
| { |
| /* CRS SYNC Error */ |
| crsstatus |= RCC_CRS_TRIMOVF; |
| |
| /* Clear CRS Error bit */ |
| __HAL_RCC_CRS_CLEAR_FLAG(RCC_CRS_FLAG_TRIMOVF); |
| } |
| |
| /* Check CRS Error flag */ |
| if(__HAL_RCC_CRS_GET_FLAG(RCC_CRS_FLAG_SYNCERR)) |
| { |
| /* CRS SYNC Error */ |
| crsstatus |= RCC_CRS_SYNCERR; |
| |
| /* Clear CRS Error bit */ |
| __HAL_RCC_CRS_CLEAR_FLAG(RCC_CRS_FLAG_SYNCERR); |
| } |
| |
| /* Check CRS SYNC Missed flag */ |
| if(__HAL_RCC_CRS_GET_FLAG(RCC_CRS_FLAG_SYNCMISS)) |
| { |
| /* CRS SYNC Missed */ |
| crsstatus |= RCC_CRS_SYNCMISS; |
| |
| /* Clear CRS SYNC Missed bit */ |
| __HAL_RCC_CRS_CLEAR_FLAG(RCC_CRS_FLAG_SYNCMISS); |
| } |
| |
| /* Check CRS Expected SYNC flag */ |
| if(__HAL_RCC_CRS_GET_FLAG(RCC_CRS_FLAG_ESYNC)) |
| { |
| /* frequency error counter reached a zero value */ |
| __HAL_RCC_CRS_CLEAR_FLAG(RCC_CRS_FLAG_ESYNC); |
| } |
| } while(RCC_CRS_NONE == crsstatus); |
| |
| return crsstatus; |
| } |
| |
| /** |
| * @brief Handle the Clock Recovery System interrupt request. |
| * @retval None |
| */ |
| void HAL_RCCEx_CRS_IRQHandler(void) |
| { |
| uint32_t crserror = RCC_CRS_NONE; |
| /* Get current IT flags and IT sources values */ |
| uint32_t itflags = READ_REG(CRS->ISR); |
| uint32_t itsources = READ_REG(CRS->CR); |
| |
| /* Check CRS SYNCOK flag */ |
| if(((itflags & RCC_CRS_FLAG_SYNCOK) != 0U) && ((itsources & RCC_CRS_IT_SYNCOK) != 0U)) |
| { |
| /* Clear CRS SYNC event OK flag */ |
| WRITE_REG(CRS->ICR, CRS_ICR_SYNCOKC); |
| |
| /* user callback */ |
| HAL_RCCEx_CRS_SyncOkCallback(); |
| } |
| /* Check CRS SYNCWARN flag */ |
| else if(((itflags & RCC_CRS_FLAG_SYNCWARN) != 0U) && ((itsources & RCC_CRS_IT_SYNCWARN) != 0U)) |
| { |
| /* Clear CRS SYNCWARN flag */ |
| WRITE_REG(CRS->ICR, CRS_ICR_SYNCWARNC); |
| |
| /* user callback */ |
| HAL_RCCEx_CRS_SyncWarnCallback(); |
| } |
| /* Check CRS Expected SYNC flag */ |
| else if(((itflags & RCC_CRS_FLAG_ESYNC) != 0U) && ((itsources & RCC_CRS_IT_ESYNC) != 0U)) |
| { |
| /* frequency error counter reached a zero value */ |
| WRITE_REG(CRS->ICR, CRS_ICR_ESYNCC); |
| |
| /* user callback */ |
| HAL_RCCEx_CRS_ExpectedSyncCallback(); |
| } |
| /* Check CRS Error flags */ |
| else |
| { |
| if(((itflags & RCC_CRS_FLAG_ERR) != 0U) && ((itsources & RCC_CRS_IT_ERR) != 0U)) |
| { |
| if((itflags & RCC_CRS_FLAG_SYNCERR) != 0U) |
| { |
| crserror |= RCC_CRS_SYNCERR; |
| } |
| if((itflags & RCC_CRS_FLAG_SYNCMISS) != 0U) |
| { |
| crserror |= RCC_CRS_SYNCMISS; |
| } |
| if((itflags & RCC_CRS_FLAG_TRIMOVF) != 0U) |
| { |
| crserror |= RCC_CRS_TRIMOVF; |
| } |
| |
| /* Clear CRS Error flags */ |
| WRITE_REG(CRS->ICR, CRS_ICR_ERRC); |
| |
| /* user error callback */ |
| HAL_RCCEx_CRS_ErrorCallback(crserror); |
| } |
| } |
| } |
| |
| /** |
| * @brief RCCEx Clock Recovery System SYNCOK interrupt callback. |
| * @retval none |
| */ |
| __weak void HAL_RCCEx_CRS_SyncOkCallback(void) |
| { |
| /* NOTE : This function should not be modified, when the callback is needed, |
| the @ref HAL_RCCEx_CRS_SyncOkCallback should be implemented in the user file |
| */ |
| } |
| |
| /** |
| * @brief RCCEx Clock Recovery System SYNCWARN interrupt callback. |
| * @retval none |
| */ |
| __weak void HAL_RCCEx_CRS_SyncWarnCallback(void) |
| { |
| /* NOTE : This function should not be modified, when the callback is needed, |
| the @ref HAL_RCCEx_CRS_SyncWarnCallback should be implemented in the user file |
| */ |
| } |
| |
| /** |
| * @brief RCCEx Clock Recovery System Expected SYNC interrupt callback. |
| * @retval none |
| */ |
| __weak void HAL_RCCEx_CRS_ExpectedSyncCallback(void) |
| { |
| /* NOTE : This function should not be modified, when the callback is needed, |
| the @ref HAL_RCCEx_CRS_ExpectedSyncCallback should be implemented in the user file |
| */ |
| } |
| |
| /** |
| * @brief RCCEx Clock Recovery System Error interrupt callback. |
| * @param Error Combination of Error status. |
| * This parameter can be a combination of the following values: |
| * @arg @ref RCC_CRS_SYNCERR |
| * @arg @ref RCC_CRS_SYNCMISS |
| * @arg @ref RCC_CRS_TRIMOVF |
| * @retval none |
| */ |
| __weak void HAL_RCCEx_CRS_ErrorCallback(uint32_t Error) |
| { |
| /* Prevent unused argument(s) compilation warning */ |
| UNUSED(Error); |
| |
| /* NOTE : This function should not be modified, when the callback is needed, |
| the @ref HAL_RCCEx_CRS_ErrorCallback should be implemented in the user file |
| */ |
| } |
| |
| /** |
| * @} |
| */ |
| |
| #endif /* CRS */ |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| #endif /* HAL_RCC_MODULE_ENABLED */ |
| /** |
| * @} |
| */ |
| |