| /** |
| ****************************************************************************** |
| * @file stm32l0xx_hal_adc.h |
| * @author MCD Application Team |
| * @brief Header file of ADC HAL module. |
| ****************************************************************************** |
| * @attention |
| * |
| * <h2><center>© Copyright(c) 2016 STMicroelectronics. |
| * All rights reserved.</center></h2> |
| * |
| * This software component is licensed by ST under BSD 3-Clause license, |
| * the "License"; You may not use this file except in compliance with the |
| * License. You may obtain a copy of the License at: |
| * opensource.org/licenses/BSD-3-Clause |
| * |
| ****************************************************************************** |
| */ |
| |
| /* Define to prevent recursive inclusion -------------------------------------*/ |
| #ifndef __STM32L0xx_HAL_ADC_H |
| #define __STM32L0xx_HAL_ADC_H |
| |
| #ifdef __cplusplus |
| extern "C" { |
| #endif |
| |
| /* Includes ------------------------------------------------------------------*/ |
| #include "stm32l0xx_hal_def.h" |
| |
| /** @addtogroup STM32L0xx_HAL_Driver |
| * @{ |
| */ |
| |
| /** @addtogroup ADC |
| * @{ |
| */ |
| |
| /* Exported types ------------------------------------------------------------*/ |
| /** @defgroup ADC_Exported_Types ADC Exported Types |
| * @{ |
| */ |
| |
| /** |
| * @brief ADC group regular oversampling structure definition |
| */ |
| typedef struct |
| { |
| uint32_t Ratio; /*!< Configures the oversampling ratio. |
| This parameter can be a value of @ref ADC_Oversampling_Ratio */ |
| |
| uint32_t RightBitShift; /*!< Configures the division coefficient for the Oversampler. |
| This parameter can be a value of @ref ADC_Right_Bit_Shift */ |
| |
| uint32_t TriggeredMode; /*!< Selects the regular triggered oversampling mode. |
| This parameter can be a value of @ref ADC_Triggered_Oversampling_Mode */ |
| }ADC_OversamplingTypeDef; |
| |
| /** |
| * @brief Structure definition of ADC instance and ADC group regular. |
| * @note Parameters of this structure are shared within 2 scopes: |
| * - Scope entire ADC (differentiation done for compatibility with some other STM32 series featuring ADC groups regular and injected): ClockPrescaler, Resolution, DataAlign, |
| * ScanConvMode, EOCSelection, LowPowerAutoWait. |
| * - Scope ADC group regular: ContinuousConvMode, NbrOfConversion, DiscontinuousConvMode, |
| * ExternalTrigConv, ExternalTrigConvEdge, DMAContinuousRequests, Overrun, OversamplingMode, Oversampling. |
| * @note The setting of these parameters by function HAL_ADC_Init() is conditioned to ADC state. |
| * ADC state can be either: |
| * - For all parameters: ADC disabled |
| * - For all parameters except 'ClockPrescaler' and 'Resolution': ADC enabled without conversion on going on group regular. |
| * If ADC is not in the appropriate state to modify some parameters, these parameters setting is bypassed |
| * without error reporting (as it can be the expected behavior in case of intended action to update another parameter |
| * (which fulfills the ADC state condition) on the fly). |
| */ |
| typedef struct |
| { |
| uint32_t ClockPrescaler; /*!< Select ADC clock source (synchronous clock derived from APB clock or asynchronous clock derived from ADC dedicated HSI RC oscillator) and clock prescaler. |
| This parameter can be a value of @ref ADC_ClockPrescaler. |
| Note: In case of synchronous clock mode based on HCLK/1, the configuration must be enabled only |
| if the system clock has a 50% duty clock cycle (APB prescaler configured inside RCC |
| must be bypassed and PCLK clock must have 50% duty cycle). Refer to reference manual for details. |
| Note: In case of usage of the ADC dedicated HSI RC oscillator, it must be preliminarily enabled at RCC top level. |
| Note: This parameter can be modified only if the ADC is disabled. */ |
| |
| uint32_t Resolution; /*!< Configure the ADC resolution. |
| This parameter can be a value of @ref ADC_Resolution */ |
| |
| uint32_t DataAlign; /*!< Specify ADC data alignment in conversion data register (right or left). |
| Refer to reference manual for alignments formats versus resolutions. |
| This parameter can be a value of @ref ADC_Data_align */ |
| |
| uint32_t ScanConvMode; /*!< Configure the sequencer of regular group. |
| This parameter can be associated to parameter 'DiscontinuousConvMode' to have main sequence subdivided in successive parts. |
| Sequencer is automatically enabled if several channels are set (sequencer cannot be disabled, as it can be the case on other STM32 devices): |
| If only 1 channel is set: Conversion is performed in single mode. |
| If several channels are set: Conversions are performed in sequence mode (ranks defined by each channel number: channel 0 fixed on rank 0, channel 1 fixed on rank1, ...). |
| Scan direction can be set to forward (from channel 0 to channel 18) or backward (from channel 18 to channel 0). |
| This parameter can be a value of @ref ADC_Scan_mode */ |
| |
| uint32_t EOCSelection; /*!< Specify which EOC (End Of Conversion) flag is used for conversion by polling and interruption: end of unitary conversion or end of sequence conversions. |
| This parameter can be a value of @ref ADC_EOCSelection. */ |
| |
| uint32_t LowPowerAutoWait; /*!< Select the dynamic low power Auto Delay: new conversion start only when the previous |
| conversion (for ADC group regular) has been retrieved by user software, |
| using function HAL_ADC_GetValue(). |
| This feature automatically adapts the frequency of ADC conversions triggers to the speed of the system that reads the data. Moreover, this avoids risk of overrun |
| for low frequency applications. |
| This parameter can be set to ENABLE or DISABLE. |
| Note: Do not use with interruption or DMA (HAL_ADC_Start_IT(), HAL_ADC_Start_DMA()) since they clear immediately the EOC flag |
| to free the IRQ vector sequencer. |
| Do use with polling: 1. Start conversion with HAL_ADC_Start(), 2. Later on, when ADC conversion data is needed: |
| use HAL_ADC_PollForConversion() to ensure that conversion is completed and HAL_ADC_GetValue() to retrieve conversion result and trig another conversion start. */ |
| |
| uint32_t LowPowerAutoPowerOff; /*!< Select the auto-off mode: the ADC automatically powers-off after a conversion and automatically wakes-up when a new conversion is triggered (with startup time between trigger and start of sampling). |
| This feature can be combined with automatic wait mode (parameter 'LowPowerAutoWait'). |
| This parameter can be set to ENABLE or DISABLE. |
| Note: If enabled, this feature also turns off the ADC dedicated 14 MHz RC oscillator (HSI14) */ |
| |
| FunctionalState ContinuousConvMode; /*!< Specify whether the conversion is performed in single mode (one conversion) or continuous mode for ADC group regular, |
| after the first ADC conversion start trigger occurred (software start or external trigger). |
| This parameter can be set to ENABLE or DISABLE. */ |
| |
| FunctionalState DiscontinuousConvMode; /*!< Specify whether the conversions sequence of ADC group regular is performed in Complete-sequence/Discontinuous-sequence |
| (main sequence subdivided in successive parts). |
| Discontinuous mode is used only if sequencer is enabled (parameter 'ScanConvMode'). If sequencer is disabled, this parameter is discarded. |
| Discontinuous mode can be enabled only if continuous mode is disabled. If continuous mode is enabled, this parameter setting is discarded. |
| This parameter can be set to ENABLE or DISABLE. |
| Note: On this STM32 serie, ADC group regular number of discontinuous ranks increment is fixed to one-by-one. */ |
| |
| uint32_t ExternalTrigConv; /*!< Select the external event source used to trigger ADC group regular conversion start. |
| If set to ADC_SOFTWARE_START, external triggers are disabled and software trigger is used instead. |
| This parameter can be a value of @ref ADC_regular_external_trigger_source. |
| Caution: external trigger source is common to all ADC instances. */ |
| |
| uint32_t ExternalTrigConvEdge; /*!< Select the external event edge used to trigger ADC group regular conversion start. |
| If trigger source is set to ADC_SOFTWARE_START, this parameter is discarded. |
| This parameter can be a value of @ref ADC_regular_external_trigger_edge */ |
| |
| FunctionalState DMAContinuousRequests; /*!< Specify whether the DMA requests are performed in one shot mode (DMA transfer stops when number of conversions is reached) |
| or in continuous mode (DMA transfer unlimited, whatever number of conversions). |
| This parameter can be set to ENABLE or DISABLE. |
| Note: In continuous mode, DMA must be configured in circular mode. Otherwise an overrun will be triggered when DMA buffer maximum pointer is reached. */ |
| |
| uint32_t Overrun; /*!< Select the behavior in case of overrun: data overwritten or preserved (default). |
| This parameter can be a value of @ref ADC_Overrun. |
| Note: In case of overrun set to data preserved and usage with programming model with interruption (HAL_Start_IT()): ADC IRQ handler has to clear |
| end of conversion flags, this induces the release of the preserved data. If needed, this data can be saved in function |
| HAL_ADC_ConvCpltCallback(), placed in user program code (called before end of conversion flags clear). |
| Note: Error reporting with respect to the conversion mode: |
| - Usage with ADC conversion by polling for event or interruption: Error is reported only if overrun is set to data preserved. If overrun is set to data |
| overwritten, user can willingly not read all the converted data, this is not considered as an erroneous case. |
| - Usage with ADC conversion by DMA: Error is reported whatever overrun setting (DMA is expected to process all data from data register). */ |
| |
| uint32_t LowPowerFrequencyMode; /*!< When selecting an analog ADC clock frequency lower than 2.8MHz, |
| it is mandatory to first enable the Low Frequency Mode. |
| This parameter can be set to ENABLE or DISABLE. |
| Note: This parameter can be modified only if there is no conversion is ongoing. */ |
| |
| |
| uint32_t SamplingTime; /*!< The sample time common to all channels. |
| Unit: ADC clock cycles |
| This parameter can be a value of @ref ADC_sampling_times |
| Note: This parameter can be modified only if there is no conversion ongoing. */ |
| |
| uint32_t OversamplingMode; /*!< Specify whether the oversampling feature is enabled or disabled. |
| This parameter can be set to ENABLE or DISABLE. |
| Note: This parameter can be modified only if there is no conversion is ongoing on ADC group regular. */ |
| |
| |
| ADC_OversamplingTypeDef Oversample; /*!< Specify the Oversampling parameters |
| Caution: this setting overwrites the previous oversampling configuration if oversampling is already enabled. */ |
| }ADC_InitTypeDef; |
| |
| /** |
| * @brief Structure definition of ADC channel for regular group |
| * @note The setting of these parameters by function HAL_ADC_ConfigChannel() is conditioned to ADC state. |
| * ADC state can be either: |
| * - For all parameters: ADC disabled or enabled without conversion on going on regular group. |
| * If ADC is not in the appropriate state to modify some parameters, these parameters setting is bypassed |
| * without error reporting (as it can be the expected behavior in case of intended action to update another parameter (which fulfills the ADC state condition) on the fly). |
| */ |
| typedef struct |
| { |
| uint32_t Channel; /*!< Specify the channel to configure into ADC regular group. |
| This parameter can be a value of @ref ADC_channels |
| Note: Depending on devices, some channels may not be available on device package pins. Refer to device datasheet for channels availability. */ |
| |
| uint32_t Rank; /*!< Add or remove the channel from ADC regular group sequencer. |
| On STM32L0 devices, number of ranks in the sequence is defined by number of channels enabled, rank of each channel is defined by channel number |
| (channel 0 fixed on rank 0, channel 1 fixed on rank1, ...). |
| Despite the channel rank is fixed, this parameter allow an additional possibility: to remove the selected rank (selected channel) from sequencer. |
| This parameter can be a value of @ref ADC_rank */ |
| }ADC_ChannelConfTypeDef; |
| |
| /** |
| * @brief Structure definition of ADC analog watchdog |
| * @note The setting of these parameters by function HAL_ADC_AnalogWDGConfig() is conditioned to ADC state. |
| * ADC state can be either: |
| * - For all parameters: ADC disabled or ADC enabled without conversion on going on ADC group regular |
| * - For parameters 'HighThreshold' and 'LowThreshold': ADC enabled with conversion on going on regular group (AWD thresholds can be modify on the fly while ADC conversion is on going) |
| */ |
| typedef struct |
| { |
| uint32_t WatchdogMode; /*!< Configure the ADC analog watchdog mode: single/all channels. |
| This parameter can be a value of @ref ADC_analog_watchdog_mode */ |
| |
| uint32_t Channel; /*!< Select which ADC channel to monitor by analog watchdog. |
| This parameter has an effect only if watchdog mode is configured on single channel (parameter WatchdogMode) |
| This parameter can be a value of @ref ADC_channels */ |
| |
| FunctionalState ITMode; /*!< Specify whether the analog watchdog is configured in interrupt or polling mode. |
| This parameter can be set to ENABLE or DISABLE */ |
| uint32_t HighThreshold; /*!< Configures the ADC analog watchdog High threshold value. |
| Depending of ADC resolution selected (12, 10, 8 or 6 bits), |
| this parameter must be a number between Min_Data = 0x000 and Max_Data = 0xFFF, 0x3FF, 0xFF or 0x3F respectively. */ |
| |
| uint32_t LowThreshold; /*!< Configures the ADC analog watchdog High threshold value. |
| Depending of ADC resolution selected (12, 10, 8 or 6 bits), |
| this parameter must be a number between Min_Data = 0x000 and Max_Data = 0xFFF, 0x3FF, 0xFF or 0x3F respectively. */ |
| }ADC_AnalogWDGConfTypeDef; |
| |
| /** |
| * @brief HAL ADC state machine: ADC states definition (bitfields) |
| * @note ADC state machine is managed by bitfields, state must be compared |
| * with bit by bit. |
| * For example: |
| * " if (HAL_IS_BIT_SET(HAL_ADC_GetState(hadc1), HAL_ADC_STATE_REG_BUSY)) " |
| * " if (HAL_IS_BIT_SET(HAL_ADC_GetState(hadc1), HAL_ADC_STATE_AWD1) ) " |
| */ |
| /* States of ADC global scope */ |
| #define HAL_ADC_STATE_RESET ((uint32_t)0x00000000) /*!< ADC not yet initialized or disabled */ |
| #define HAL_ADC_STATE_READY ((uint32_t)0x00000001) /*!< ADC peripheral ready for use */ |
| #define HAL_ADC_STATE_BUSY_INTERNAL ((uint32_t)0x00000002) /*!< ADC is busy due to an internal process (initialization, calibration) */ |
| #define HAL_ADC_STATE_TIMEOUT ((uint32_t)0x00000004) /*!< TimeOut occurrence */ |
| |
| /* States of ADC errors */ |
| #define HAL_ADC_STATE_ERROR_INTERNAL ((uint32_t)0x00000010) /*!< Internal error occurrence */ |
| #define HAL_ADC_STATE_ERROR_CONFIG ((uint32_t)0x00000020) /*!< Configuration error occurrence */ |
| #define HAL_ADC_STATE_ERROR_DMA ((uint32_t)0x00000040) /*!< DMA error occurrence */ |
| |
| /* States of ADC group regular */ |
| #define HAL_ADC_STATE_REG_BUSY ((uint32_t)0x00000100) /*!< A conversion on ADC group regular is ongoing or can occur (either by continuous mode, |
| external trigger, low power auto power-on (if feature available), multimode ADC master control (if feature available)) */ |
| #define HAL_ADC_STATE_REG_EOC ((uint32_t)0x00000200) /*!< Conversion data available on group regular */ |
| #define HAL_ADC_STATE_REG_OVR ((uint32_t)0x00000400) /*!< Overrun occurrence */ |
| #define HAL_ADC_STATE_REG_EOSMP ((uint32_t)0x00000800) /*!< Not available on this STM32 serie: End Of Sampling flag raised */ |
| |
| /* States of ADC group injected */ |
| #define HAL_ADC_STATE_INJ_BUSY ((uint32_t)0x00001000) /*!< Not available on this STM32 serie: A conversion on group injected is ongoing or can occur (either by auto-injection mode, |
| external trigger, low power auto power-on (if feature available), multimode ADC master control (if feature available)) */ |
| #define HAL_ADC_STATE_INJ_EOC ((uint32_t)0x00002000) /*!< Not available on this STM32 serie: Conversion data available on group injected */ |
| #define HAL_ADC_STATE_INJ_JQOVF ((uint32_t)0x00004000) /*!< Not available on this STM32 serie: Injected queue overflow occurrence */ |
| |
| /* States of ADC analog watchdogs */ |
| #define HAL_ADC_STATE_AWD1 ((uint32_t)0x00010000) /*!< Out-of-window occurrence of ADC analog watchdog 1 */ |
| #define HAL_ADC_STATE_AWD2 ((uint32_t)0x00020000) /*!< Not available on this STM32 serie: Out-of-window occurrence of ADC analog watchdog 2 */ |
| #define HAL_ADC_STATE_AWD3 ((uint32_t)0x00040000) /*!< Not available on this STM32 serie: Out-of-window occurrence of ADC analog watchdog 3 */ |
| |
| /* States of ADC multi-mode */ |
| #define HAL_ADC_STATE_MULTIMODE_SLAVE ((uint32_t)0x00100000) /*!< Not available on this STM32 serie: ADC in multimode slave state, controlled by another ADC master (when feature available) */ |
| |
| |
| |
| /** |
| * @brief ADC handle Structure definition |
| */ |
| typedef struct __ADC_HandleTypeDef |
| { |
| ADC_TypeDef *Instance; /*!< Register base address */ |
| |
| ADC_InitTypeDef Init; /*!< ADC required parameters */ |
| |
| DMA_HandleTypeDef *DMA_Handle; /*!< Pointer DMA Handler */ |
| |
| HAL_LockTypeDef Lock; /*!< ADC locking object */ |
| |
| __IO uint32_t State; /*!< ADC communication state (bitmap of ADC states) */ |
| |
| __IO uint32_t ErrorCode; /*!< ADC Error code */ |
| |
| |
| #if (USE_HAL_ADC_REGISTER_CALLBACKS == 1) |
| void (* ConvCpltCallback)(struct __ADC_HandleTypeDef *hadc); /*!< ADC conversion complete callback */ |
| void (* ConvHalfCpltCallback)(struct __ADC_HandleTypeDef *hadc); /*!< ADC conversion DMA half-transfer callback */ |
| void (* LevelOutOfWindowCallback)(struct __ADC_HandleTypeDef *hadc); /*!< ADC analog watchdog 1 callback */ |
| void (* ErrorCallback)(struct __ADC_HandleTypeDef *hadc); /*!< ADC error callback */ |
| void (* MspInitCallback)(struct __ADC_HandleTypeDef *hadc); /*!< ADC Msp Init callback */ |
| void (* MspDeInitCallback)(struct __ADC_HandleTypeDef *hadc); /*!< ADC Msp DeInit callback */ |
| #endif /* USE_HAL_ADC_REGISTER_CALLBACKS */ |
| }ADC_HandleTypeDef; |
| |
| #if (USE_HAL_ADC_REGISTER_CALLBACKS == 1) |
| /** |
| * @brief HAL ADC Callback ID enumeration definition |
| */ |
| typedef enum |
| { |
| HAL_ADC_CONVERSION_COMPLETE_CB_ID = 0x00U, /*!< ADC conversion complete callback ID */ |
| HAL_ADC_CONVERSION_HALF_CB_ID = 0x01U, /*!< ADC conversion DMA half-transfer callback ID */ |
| HAL_ADC_LEVEL_OUT_OF_WINDOW_1_CB_ID = 0x02U, /*!< ADC analog watchdog 1 callback ID */ |
| HAL_ADC_ERROR_CB_ID = 0x03U, /*!< ADC error callback ID */ |
| HAL_ADC_INJ_CONVERSION_COMPLETE_CB_ID = 0x04U, /*!< ADC group injected conversion complete callback ID */ |
| HAL_ADC_MSPINIT_CB_ID = 0x09U, /*!< ADC Msp Init callback ID */ |
| HAL_ADC_MSPDEINIT_CB_ID = 0x0AU /*!< ADC Msp DeInit callback ID */ |
| } HAL_ADC_CallbackIDTypeDef; |
| |
| /** |
| * @brief HAL ADC Callback pointer definition |
| */ |
| typedef void (*pADC_CallbackTypeDef)(ADC_HandleTypeDef *hadc); /*!< pointer to a ADC callback function */ |
| |
| #endif /* USE_HAL_ADC_REGISTER_CALLBACKS */ |
| |
| /** |
| * @} |
| */ |
| |
| |
| /* Exported constants --------------------------------------------------------*/ |
| |
| /** @defgroup ADC_Exported_Constants ADC Exported Constants |
| * @{ |
| */ |
| |
| /** @defgroup ADC_Error_Code ADC Error Code |
| * @{ |
| */ |
| #define HAL_ADC_ERROR_NONE ((uint32_t)0x00U) /*!< No error */ |
| #define HAL_ADC_ERROR_INTERNAL ((uint32_t)0x01U) /*!< ADC peripheral internal error (problem of clocking, |
| enable/disable, erroneous state, ...) */ |
| #define HAL_ADC_ERROR_OVR ((uint32_t)0x02U) /*!< Overrun error */ |
| #define HAL_ADC_ERROR_DMA ((uint32_t)0x04U) /*!< DMA transfer error */ |
| |
| #if (USE_HAL_ADC_REGISTER_CALLBACKS == 1) |
| #define HAL_ADC_ERROR_INVALID_CALLBACK (0x10U) /*!< Invalid Callback error */ |
| #endif /* USE_HAL_ADC_REGISTER_CALLBACKS */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup ADC_TimeOut_Values ADC TimeOut Values |
| * @{ |
| */ |
| |
| /* Fixed timeout values for ADC calibration, enable settling time, disable */ |
| /* settling time. */ |
| /* Values defined to be higher than worst cases: low clocks freq, */ |
| /* maximum prescalers. */ |
| /* Unit: ms */ |
| #define ADC_ENABLE_TIMEOUT 10U |
| #define ADC_DISABLE_TIMEOUT 10U |
| #define ADC_STOP_CONVERSION_TIMEOUT 10U |
| |
| /* Delay of 10us fixed to worst case: maximum CPU frequency 180MHz to have */ |
| /* the minimum number of CPU cycles to fulfill this delay */ |
| #define ADC_DELAY_10US_MIN_CPU_CYCLES 1800U |
| /** |
| * @} |
| */ |
| |
| /** @defgroup ADC_ClockPrescaler ADC Clock Prescaler |
| * @{ |
| */ |
| #define ADC_CLOCK_ASYNC_DIV1 ((uint32_t)0x00000000U) /*!< ADC Asynchronous clock mode divided by 1 */ |
| #define ADC_CLOCK_ASYNC_DIV2 (ADC_CCR_PRESC_0) /*!< ADC Asynchronous clock mode divided by 2 */ |
| #define ADC_CLOCK_ASYNC_DIV4 (ADC_CCR_PRESC_1) /*!< ADC Asynchronous clock mode divided by 2 */ |
| #define ADC_CLOCK_ASYNC_DIV6 (ADC_CCR_PRESC_1 | ADC_CCR_PRESC_0) /*!< ADC Asynchronous clock mode divided by 2 */ |
| #define ADC_CLOCK_ASYNC_DIV8 (ADC_CCR_PRESC_2) /*!< ADC Asynchronous clock mode divided by 2 */ |
| #define ADC_CLOCK_ASYNC_DIV10 (ADC_CCR_PRESC_2 | ADC_CCR_PRESC_0) /*!< ADC Asynchronous clock mode divided by 2 */ |
| #define ADC_CLOCK_ASYNC_DIV12 (ADC_CCR_PRESC_2 | ADC_CCR_PRESC_1) /*!< ADC Asynchronous clock mode divided by 2 */ |
| #define ADC_CLOCK_ASYNC_DIV16 (ADC_CCR_PRESC_2 | ADC_CCR_PRESC_1 | ADC_CCR_PRESC_0) /*!< ADC Asynchronous clock mode divided by 2 */ |
| #define ADC_CLOCK_ASYNC_DIV32 (ADC_CCR_PRESC_3) /*!< ADC Asynchronous clock mode divided by 2 */ |
| #define ADC_CLOCK_ASYNC_DIV64 (ADC_CCR_PRESC_3 | ADC_CCR_PRESC_0) /*!< ADC Asynchronous clock mode divided by 2 */ |
| #define ADC_CLOCK_ASYNC_DIV128 (ADC_CCR_PRESC_3 | ADC_CCR_PRESC_1) /*!< ADC Asynchronous clock mode divided by 2 */ |
| #define ADC_CLOCK_ASYNC_DIV256 (ADC_CCR_PRESC_3 | ADC_CCR_PRESC_1 | ADC_CCR_PRESC_0) /*!< ADC Asynchronous clock mode divided by 2 */ |
| |
| #define ADC_CLOCK_SYNC_PCLK_DIV1 ((uint32_t)ADC_CFGR2_CKMODE) /*!< Synchronous clock mode divided by 1 |
| This configuration must be enabled only if PCLK has a 50% |
| duty clock cycle (APB prescaler configured inside the RCC must be bypassed and the system clock |
| must by 50% duty cycle)*/ |
| #define ADC_CLOCK_SYNC_PCLK_DIV2 ((uint32_t)ADC_CFGR2_CKMODE_0) /*!< Synchronous clock mode divided by 2 */ |
| #define ADC_CLOCK_SYNC_PCLK_DIV4 ((uint32_t)ADC_CFGR2_CKMODE_1) /*!< Synchronous clock mode divided by 4 */ |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup ADC_Resolution ADC Resolution |
| * @{ |
| */ |
| #define ADC_RESOLUTION_12B ((uint32_t)0x00000000U) /*!< ADC 12-bit resolution */ |
| #define ADC_RESOLUTION_10B ((uint32_t)ADC_CFGR1_RES_0) /*!< ADC 10-bit resolution */ |
| #define ADC_RESOLUTION_8B ((uint32_t)ADC_CFGR1_RES_1) /*!< ADC 8-bit resolution */ |
| #define ADC_RESOLUTION_6B ((uint32_t)ADC_CFGR1_RES) /*!< ADC 6-bit resolution */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup ADC_Data_align ADC conversion data alignment |
| * @{ |
| */ |
| #define ADC_DATAALIGN_RIGHT ((uint32_t)0x00000000U) |
| #define ADC_DATAALIGN_LEFT ((uint32_t)ADC_CFGR1_ALIGN) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup ADC_regular_external_trigger_edge ADC External Trigger Source Edge for Regular Group |
| * @{ |
| */ |
| #define ADC_EXTERNALTRIGCONVEDGE_NONE ((uint32_t)0x00000000U) |
| #define ADC_EXTERNALTRIGCONVEDGE_RISING ((uint32_t)ADC_CFGR1_EXTEN_0) |
| #define ADC_EXTERNALTRIGCONVEDGE_FALLING ((uint32_t)ADC_CFGR1_EXTEN_1) |
| #define ADC_EXTERNALTRIGCONVEDGE_RISINGFALLING ((uint32_t)ADC_CFGR1_EXTEN) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup ADC_EOCSelection ADC EOC Selection |
| * @{ |
| */ |
| #define ADC_EOC_SINGLE_CONV ((uint32_t) ADC_ISR_EOC) |
| #define ADC_EOC_SEQ_CONV ((uint32_t) ADC_ISR_EOS) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup ADC_Overrun ADC Overrun |
| * @{ |
| */ |
| #define ADC_OVR_DATA_PRESERVED ((uint32_t)0x00000000U) |
| #define ADC_OVR_DATA_OVERWRITTEN ((uint32_t)ADC_CFGR1_OVRMOD) |
| /** |
| * @} |
| */ |
| |
| |
| /** @defgroup ADC_rank ADC rank |
| * @{ |
| */ |
| #define ADC_RANK_CHANNEL_NUMBER ((uint32_t)0x00001000U) /*!< Enable the rank of the selected channels. Number of ranks in the sequence is defined by number of channels enabled, rank of each channel is defined by channel number (channel 0 fixed on rank 0, channel 1 fixed on rank1, ...) */ |
| #define ADC_RANK_NONE ((uint32_t)0x00001001U) /*!< Disable the selected rank (selected channel) from sequencer */ |
| /** |
| * @} |
| */ |
| |
| |
| /** @defgroup ADC_channels ADC_Channels |
| * @{ |
| */ |
| #define ADC_CHANNEL_0 ((uint32_t)(ADC_CHSELR_CHSEL0)) |
| #define ADC_CHANNEL_1 ((uint32_t)(ADC_CHSELR_CHSEL1) | ADC_CFGR1_AWDCH_0) |
| #define ADC_CHANNEL_2 ((uint32_t)(ADC_CHSELR_CHSEL2) | ADC_CFGR1_AWDCH_1) |
| #define ADC_CHANNEL_3 ((uint32_t)(ADC_CHSELR_CHSEL3)| ADC_CFGR1_AWDCH_1 | ADC_CFGR1_AWDCH_0) |
| #define ADC_CHANNEL_4 ((uint32_t)(ADC_CHSELR_CHSEL4)| ADC_CFGR1_AWDCH_2) |
| #define ADC_CHANNEL_5 ((uint32_t)(ADC_CHSELR_CHSEL5)| ADC_CFGR1_AWDCH_2| ADC_CFGR1_AWDCH_0) |
| #define ADC_CHANNEL_6 ((uint32_t)(ADC_CHSELR_CHSEL6)| ADC_CFGR1_AWDCH_2| ADC_CFGR1_AWDCH_1) |
| #define ADC_CHANNEL_7 ((uint32_t)(ADC_CHSELR_CHSEL7)| ADC_CFGR1_AWDCH_2| ADC_CFGR1_AWDCH_1 | ADC_CFGR1_AWDCH_0) |
| #define ADC_CHANNEL_8 ((uint32_t)(ADC_CHSELR_CHSEL8)| ADC_CFGR1_AWDCH_3) |
| #define ADC_CHANNEL_9 ((uint32_t)(ADC_CHSELR_CHSEL9)| ADC_CFGR1_AWDCH_3| ADC_CFGR1_AWDCH_0) |
| #define ADC_CHANNEL_10 ((uint32_t)(ADC_CHSELR_CHSEL10)| ADC_CFGR1_AWDCH_3| ADC_CFGR1_AWDCH_1) |
| #define ADC_CHANNEL_11 ((uint32_t)(ADC_CHSELR_CHSEL11)| ADC_CFGR1_AWDCH_3| ADC_CFGR1_AWDCH_1| ADC_CFGR1_AWDCH_0) |
| #define ADC_CHANNEL_12 ((uint32_t)(ADC_CHSELR_CHSEL12)| ADC_CFGR1_AWDCH_3| ADC_CFGR1_AWDCH_2) |
| #define ADC_CHANNEL_13 ((uint32_t)(ADC_CHSELR_CHSEL13)| ADC_CFGR1_AWDCH_3| ADC_CFGR1_AWDCH_2| ADC_CFGR1_AWDCH_0) |
| #define ADC_CHANNEL_14 ((uint32_t)(ADC_CHSELR_CHSEL14)| ADC_CFGR1_AWDCH_3| ADC_CFGR1_AWDCH_2| ADC_CFGR1_AWDCH_1) |
| #define ADC_CHANNEL_15 ((uint32_t)(ADC_CHSELR_CHSEL15)| ADC_CFGR1_AWDCH_3| ADC_CFGR1_AWDCH_2| ADC_CFGR1_AWDCH_1| ADC_CFGR1_AWDCH_0) |
| #if defined (STM32L053xx) || defined (STM32L063xx) || defined (STM32L073xx) || defined (STM32L083xx) |
| #define ADC_CHANNEL_16 ((uint32_t)(ADC_CHSELR_CHSEL16)| ADC_CFGR1_AWDCH_4) |
| #endif |
| #define ADC_CHANNEL_17 ((uint32_t)(ADC_CHSELR_CHSEL17)| ADC_CFGR1_AWDCH_4| ADC_CFGR1_AWDCH_0) |
| #define ADC_CHANNEL_18 ((uint32_t)(ADC_CHSELR_CHSEL18)| ADC_CFGR1_AWDCH_4| ADC_CFGR1_AWDCH_1) |
| |
| /* Internal channels */ |
| #if defined (STM32L053xx) || defined (STM32L063xx) || defined (STM32L073xx) || defined (STM32L083xx) |
| #define ADC_CHANNEL_VLCD ADC_CHANNEL_16 |
| #endif |
| #define ADC_CHANNEL_VREFINT ADC_CHANNEL_17 |
| #if defined(ADC_CCR_TSEN) |
| #define ADC_CHANNEL_TEMPSENSOR ADC_CHANNEL_18 |
| #endif |
| /** |
| * @} |
| */ |
| |
| /** @defgroup ADC_Channel_AWD_Masks ADC Channel Masks |
| * @{ |
| */ |
| #define ADC_CHANNEL_MASK ((uint32_t)0x0007FFFFU) |
| #define ADC_CHANNEL_AWD_MASK ((uint32_t)0x7C000000U) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup ADC_sampling_times ADC Sampling Cycles |
| * @{ |
| */ |
| #define ADC_SAMPLETIME_1CYCLE_5 ((uint32_t)0x00000000U) /*!< ADC sampling time 1.5 cycle */ |
| #define ADC_SAMPLETIME_3CYCLES_5 ((uint32_t)ADC_SMPR_SMPR_0) /*!< ADC sampling time 3.5 CYCLES */ |
| #define ADC_SAMPLETIME_7CYCLES_5 ((uint32_t)ADC_SMPR_SMPR_1) /*!< ADC sampling time 7.5 CYCLES */ |
| #define ADC_SAMPLETIME_12CYCLES_5 ((uint32_t)(ADC_SMPR_SMPR_1 | ADC_SMPR_SMPR_0)) /*!< ADC sampling time 12.5 CYCLES */ |
| #define ADC_SAMPLETIME_19CYCLES_5 ((uint32_t)ADC_SMPR_SMPR_2) /*!< ADC sampling time 19.5 CYCLES */ |
| #define ADC_SAMPLETIME_39CYCLES_5 ((uint32_t)(ADC_SMPR_SMPR_2 | ADC_SMPR_SMPR_0)) /*!< ADC sampling time 39.5 CYCLES */ |
| #define ADC_SAMPLETIME_79CYCLES_5 ((uint32_t)(ADC_SMPR_SMPR_2 | ADC_SMPR_SMPR_1)) /*!< ADC sampling time 79.5 CYCLES */ |
| #define ADC_SAMPLETIME_160CYCLES_5 ((uint32_t)ADC_SMPR_SMPR) /*!< ADC sampling time 160.5 CYCLES */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup ADC_Scan_mode ADC Scan mode |
| * @{ |
| */ |
| /* Note: Scan mode values must be compatible with other STM32 devices having */ |
| /* a configurable sequencer. */ |
| /* Scan direction setting values are defined by taking in account */ |
| /* already defined values for other STM32 devices: */ |
| /* ADC_SCAN_DISABLE ((uint32_t)0x00000000) */ |
| /* ADC_SCAN_ENABLE ((uint32_t)0x00000001) */ |
| /* Scan direction forward is considered as default setting equivalent */ |
| /* to scan enable. */ |
| /* Scan direction backward is considered as additional setting. */ |
| /* In case of migration from another STM32 device, the user will be */ |
| /* warned of change of setting choices with assert check. */ |
| #define ADC_SCAN_DIRECTION_FORWARD ((uint32_t)0x00000001U) /*!< Scan direction forward: from channel 0 to channel 18 */ |
| #define ADC_SCAN_DIRECTION_BACKWARD ((uint32_t)0x00000002U) /*!< Scan direction backward: from channel 18 to channel 0 */ |
| |
| #define ADC_SCAN_ENABLE ADC_SCAN_DIRECTION_FORWARD /* For compatibility with other STM32 devices */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup ADC_Oversampling_Ratio ADC Oversampling Ratio |
| * @{ |
| */ |
| |
| #define ADC_OVERSAMPLING_RATIO_2 ((uint32_t)0x00000000U) /*!< ADC Oversampling ratio 2x */ |
| #define ADC_OVERSAMPLING_RATIO_4 ((uint32_t)0x00000004U) /*!< ADC Oversampling ratio 4x */ |
| #define ADC_OVERSAMPLING_RATIO_8 ((uint32_t)0x00000008U) /*!< ADC Oversampling ratio 8x */ |
| #define ADC_OVERSAMPLING_RATIO_16 ((uint32_t)0x0000000CU) /*!< ADC Oversampling ratio 16x */ |
| #define ADC_OVERSAMPLING_RATIO_32 ((uint32_t)0x00000010U) /*!< ADC Oversampling ratio 32x */ |
| #define ADC_OVERSAMPLING_RATIO_64 ((uint32_t)0x00000014U) /*!< ADC Oversampling ratio 64x */ |
| #define ADC_OVERSAMPLING_RATIO_128 ((uint32_t)0x00000018U) /*!< ADC Oversampling ratio 128x */ |
| #define ADC_OVERSAMPLING_RATIO_256 ((uint32_t)0x0000001CU) /*!< ADC Oversampling ratio 256x */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup ADC_Right_Bit_Shift ADC Right Bit Shift |
| * @{ |
| */ |
| #define ADC_RIGHTBITSHIFT_NONE ((uint32_t)0x00000000U) /*!< ADC No bit shift for oversampling */ |
| #define ADC_RIGHTBITSHIFT_1 ((uint32_t)0x00000020U) /*!< ADC 1 bit shift for oversampling */ |
| #define ADC_RIGHTBITSHIFT_2 ((uint32_t)0x00000040U) /*!< ADC 2 bits shift for oversampling */ |
| #define ADC_RIGHTBITSHIFT_3 ((uint32_t)0x00000060U) /*!< ADC 3 bits shift for oversampling */ |
| #define ADC_RIGHTBITSHIFT_4 ((uint32_t)0x00000080U) /*!< ADC 4 bits shift for oversampling */ |
| #define ADC_RIGHTBITSHIFT_5 ((uint32_t)0x000000A0U) /*!< ADC 5 bits shift for oversampling */ |
| #define ADC_RIGHTBITSHIFT_6 ((uint32_t)0x000000C0U) /*!< ADC 6 bits shift for oversampling */ |
| #define ADC_RIGHTBITSHIFT_7 ((uint32_t)0x000000E0U) /*!< ADC 7 bits shift for oversampling */ |
| #define ADC_RIGHTBITSHIFT_8 ((uint32_t)0x00000100U) /*!< ADC 8 bits shift for oversampling */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup ADC_Triggered_Oversampling_Mode ADC Triggered Oversampling Mode |
| * @{ |
| */ |
| #define ADC_TRIGGEREDMODE_SINGLE_TRIGGER ((uint32_t)0x00000000U) /*!< ADC No bit shift for oversampling */ |
| #define ADC_TRIGGEREDMODE_MULTI_TRIGGER ((uint32_t)0x00000200U) /*!< ADC No bit shift for oversampling */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup ADC_analog_watchdog_mode ADC Analog Watchdog Mode |
| * @{ |
| */ |
| #define ADC_ANALOGWATCHDOG_NONE ((uint32_t) 0x00000000U) |
| #define ADC_ANALOGWATCHDOG_SINGLE_REG ((uint32_t)(ADC_CFGR1_AWDSGL | ADC_CFGR1_AWDEN)) |
| #define ADC_ANALOGWATCHDOG_ALL_REG ((uint32_t) ADC_CFGR1_AWDEN) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup ADC_conversion_type ADC Conversion Group |
| * @{ |
| */ |
| #define ADC_REGULAR_GROUP ((uint32_t)(ADC_FLAG_EOC | ADC_FLAG_EOS)) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup ADC_Event_type ADC Event |
| * @{ |
| */ |
| #define ADC_AWD_EVENT ((uint32_t)ADC_FLAG_AWD) |
| #define ADC_OVR_EVENT ((uint32_t)ADC_FLAG_OVR) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup ADC_interrupts_definition ADC Interrupts Definition |
| * @{ |
| */ |
| #define ADC_IT_RDY ADC_IER_ADRDYIE /*!< ADC Ready (ADRDY) interrupt source */ |
| #define ADC_IT_EOSMP ADC_IER_EOSMPIE /*!< ADC End of Sampling interrupt source */ |
| #define ADC_IT_EOC ADC_IER_EOCIE /*!< ADC End of Regular Conversion interrupt source */ |
| #define ADC_IT_EOS ADC_IER_EOSEQIE /*!< ADC End of Regular sequence of Conversions interrupt source */ |
| #define ADC_IT_OVR ADC_IER_OVRIE /*!< ADC overrun interrupt source */ |
| #define ADC_IT_AWD ADC_IER_AWDIE /*!< ADC Analog watchdog 1 interrupt source */ |
| #define ADC_IT_EOCAL ADC_IER_EOCALIE /*!< ADC End of Calibration interrupt source */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup ADC_flags_definition ADC flags definition |
| * @{ |
| */ |
| #define ADC_FLAG_RDY ADC_ISR_ADRDY /*!< ADC Ready flag */ |
| #define ADC_FLAG_EOSMP ADC_ISR_EOSMP /*!< ADC End of Sampling flag */ |
| #define ADC_FLAG_EOC ADC_ISR_EOC /*!< ADC End of Regular Conversion flag */ |
| #define ADC_FLAG_EOS ADC_ISR_EOSEQ /*!< ADC End of Regular sequence of Conversions flag */ |
| #define ADC_FLAG_OVR ADC_ISR_OVR /*!< ADC overrun flag */ |
| #define ADC_FLAG_AWD ADC_ISR_AWD /*!< ADC Analog watchdog flag */ |
| #define ADC_FLAG_EOCAL ADC_ISR_EOCAL /*!< ADC Enf Of Calibration flag */ |
| |
| |
| #define ADC_FLAG_ALL (ADC_FLAG_RDY | ADC_FLAG_EOSMP | ADC_FLAG_EOC | ADC_FLAG_EOS | \ |
| ADC_FLAG_OVR | ADC_FLAG_AWD | ADC_FLAG_EOCAL) |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| |
| /* Exported macro ------------------------------------------------------------*/ |
| |
| /** @defgroup ADC_Exported_Macros ADC Exported Macros |
| * @{ |
| */ |
| /** @brief Reset ADC handle state |
| * @param __HANDLE__ ADC handle |
| * @retval None |
| */ |
| #if (USE_HAL_ADC_REGISTER_CALLBACKS == 1) |
| #define __HAL_ADC_RESET_HANDLE_STATE(__HANDLE__) \ |
| do{ \ |
| (__HANDLE__)->State = HAL_ADC_STATE_RESET; \ |
| (__HANDLE__)->MspInitCallback = NULL; \ |
| (__HANDLE__)->MspDeInitCallback = NULL; \ |
| } while(0) |
| #else |
| #define __HAL_ADC_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_ADC_STATE_RESET) |
| #endif |
| |
| /** |
| * @brief Enable the ADC peripheral |
| * @param __HANDLE__ ADC handle |
| * @retval None |
| */ |
| #define __HAL_ADC_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR |= ADC_CR_ADEN) |
| |
| /** |
| * @brief Verification of hardware constraints before ADC can be enabled |
| * @param __HANDLE__ ADC handle |
| * @retval SET (ADC can be enabled) or RESET (ADC cannot be enabled) |
| */ |
| #define ADC_ENABLING_CONDITIONS(__HANDLE__) \ |
| (( ( ((__HANDLE__)->Instance->CR) & \ |
| (ADC_CR_ADCAL | ADC_CR_ADSTP | ADC_CR_ADSTART | \ |
| ADC_CR_ADDIS | ADC_CR_ADEN ) \ |
| ) == RESET \ |
| ) ? SET : RESET) |
| |
| /** |
| * @brief Disable the ADC peripheral |
| * @param __HANDLE__ ADC handle |
| * @retval None |
| */ |
| #define __HAL_ADC_DISABLE(__HANDLE__) \ |
| do{ \ |
| (__HANDLE__)->Instance->CR |= ADC_CR_ADDIS; \ |
| __HAL_ADC_CLEAR_FLAG((__HANDLE__), (ADC_FLAG_EOSMP | ADC_FLAG_RDY)); \ |
| } while(0) |
| |
| /** |
| * @brief Verification of hardware constraints before ADC can be disabled |
| * @param __HANDLE__ ADC handle |
| * @retval SET (ADC can be disabled) or RESET (ADC cannot be disabled) |
| */ |
| #define ADC_DISABLING_CONDITIONS(__HANDLE__) \ |
| (( ( ((__HANDLE__)->Instance->CR) & \ |
| (ADC_CR_ADSTART | ADC_CR_ADEN)) == ADC_CR_ADEN \ |
| ) ? SET : RESET) |
| |
| /** |
| * @brief Verification of ADC state: enabled or disabled |
| * @param __HANDLE__ ADC handle |
| * @retval SET (ADC enabled) or RESET (ADC disabled) |
| */ |
| #define ADC_IS_ENABLE(__HANDLE__) \ |
| (( ((((__HANDLE__)->Instance->CR) & (ADC_CR_ADEN | ADC_CR_ADDIS)) == ADC_CR_ADEN) && \ |
| ((((__HANDLE__)->Instance->ISR) & ADC_FLAG_RDY) == ADC_FLAG_RDY) \ |
| ) ? SET : RESET) |
| |
| /** |
| * @brief Returns resolution bits in CFGR register: RES[1:0]. Return value among parameter to @ref ADC_Resolution. |
| * @param __HANDLE__ ADC handle |
| * @retval None |
| */ |
| #define ADC_GET_RESOLUTION(__HANDLE__) (((__HANDLE__)->Instance->CFGR1) & ADC_CFGR1_RES) |
| /** |
| * @brief Test if conversion trigger of regular group is software start |
| * or external trigger. |
| * @param __HANDLE__ ADC handle |
| * @retval SET (software start) or RESET (external trigger) |
| */ |
| #define ADC_IS_SOFTWARE_START_REGULAR(__HANDLE__) \ |
| (((__HANDLE__)->Instance->CFGR1 & ADC_CFGR1_EXTEN) == RESET) |
| |
| |
| |
| /** |
| * @brief Check if no conversion on going on regular group |
| * @param __HANDLE__ ADC handle |
| * @retval SET (conversion is on going) or RESET (no conversion is on going) |
| */ |
| #define ADC_IS_CONVERSION_ONGOING_REGULAR(__HANDLE__) \ |
| (( (((__HANDLE__)->Instance->CR) & ADC_CR_ADSTART) == RESET \ |
| ) ? RESET : SET) |
| |
| /** |
| * @brief Enable ADC continuous conversion mode. |
| * @param _CONTINUOUS_MODE_ Continuous mode. |
| * @retval None |
| */ |
| #define ADC_CONTINUOUS(_CONTINUOUS_MODE_) ((_CONTINUOUS_MODE_) << 13U) |
| |
| /** |
| * @brief Enable ADC scan mode to convert multiple ranks with sequencer. |
| * @param _SCAN_MODE_ Scan conversion mode. |
| * @retval None |
| */ |
| #define ADC_SCANDIR(_SCAN_MODE_) \ |
| ( ( (_SCAN_MODE_) == (ADC_SCAN_DIRECTION_BACKWARD) \ |
| )? (ADC_CFGR1_SCANDIR) : (0x00000000U) \ |
| ) |
| |
| /** |
| * @brief Configures the number of discontinuous conversions for the regular group channels. |
| * @param _NBR_DISCONTINUOUS_CONV_ Number of discontinuous conversions. |
| * @retval None |
| */ |
| #define __HAL_ADC_CFGR1_DISCONTINUOUS_NUM(_NBR_DISCONTINUOUS_CONV_) (((_NBR_DISCONTINUOUS_CONV_) - 1U) << 17U) |
| |
| /** |
| * @brief Enable the ADC DMA continuous request. |
| * @param _DMAContReq_MODE_ DMA continuous request mode. |
| * @retval None |
| */ |
| #define ADC_DMACONTREQ(_DMAContReq_MODE_) ((_DMAContReq_MODE_) << 1U) |
| |
| /** |
| * @brief Enable the ADC Auto Delay. |
| * @param _AutoDelay_ Auto delay bit enable or disable. |
| * @retval None |
| */ |
| #define __HAL_ADC_CFGR1_AutoDelay(_AutoDelay_) ((_AutoDelay_) << 14U) |
| |
| /** |
| * @brief Enable the ADC LowPowerAutoPowerOff. |
| * @param _AUTOFF_ AutoOff bit enable or disable. |
| * @retval None |
| */ |
| #define __HAL_ADC_CFGR1_AUTOFF(_AUTOFF_) ((_AUTOFF_) << 15U) |
| |
| /** |
| * @brief Configure the analog watchdog high threshold into registers TR1, TR2 or TR3. |
| * @param _Threshold_ Threshold value |
| * @retval None |
| */ |
| #define ADC_TRX_HIGHTHRESHOLD(_Threshold_) ((_Threshold_) << 16U) |
| |
| /** |
| * @brief Enable the ADC Low Frequency mode. |
| * @param _LOW_FREQUENCY_MODE_ Low Frequency mode. |
| * @retval None |
| */ |
| #define __HAL_ADC_CCR_LOWFREQUENCY(_LOW_FREQUENCY_MODE_) ((_LOW_FREQUENCY_MODE_) << 25U) |
| |
| /** |
| * @brief Shift the offset in function of the selected ADC resolution. |
| * Offset has to be left-aligned on bit 11, the LSB (right bits) are set to 0 |
| * If resolution 12 bits, no shift. |
| * If resolution 10 bits, shift of 2 ranks on the right. |
| * If resolution 8 bits, shift of 4 ranks on the right. |
| * If resolution 6 bits, shift of 6 ranks on the right. |
| * therefore, shift = (12 - resolution) = 12 - (12- (((RES[1:0]) >> 3)*2)) |
| * @param __HANDLE__ ADC handle. |
| * @param _Offset_ Value to be shifted |
| * @retval None |
| */ |
| #define ADC_OFFSET_SHIFT_RESOLUTION(__HANDLE__, _Offset_) \ |
| ((_Offset_) << ((((__HANDLE__)->Instance->CFGR & ADC_CFGR1_RES) >> 3U)*2U)) |
| |
| /** |
| * @brief Shift the AWD1 threshold in function of the selected ADC resolution. |
| * Thresholds have to be left-aligned on bit 11, the LSB (right bits) are set to 0 |
| * If resolution 12 bits, no shift. |
| * If resolution 10 bits, shift of 2 ranks on the right. |
| * If resolution 8 bits, shift of 4 ranks on the right. |
| * If resolution 6 bits, shift of 6 ranks on the right. |
| * therefore, shift = (12 - resolution) = 12 - (12- (((RES[1:0]) >> 3)*2)) |
| * @param __HANDLE__ ADC handle. |
| * @param _Threshold_ Value to be shifted |
| * @retval None |
| */ |
| #define ADC_AWD1THRESHOLD_SHIFT_RESOLUTION(__HANDLE__, _Threshold_) \ |
| ((_Threshold_) << ((((__HANDLE__)->Instance->CFGR1 & ADC_CFGR1_RES) >> 3U)*2U)) |
| |
| /** |
| * @brief Shift the value on the left, less significant are set to 0. |
| * @param _Value_ Value to be shifted |
| * @param _Shift_ Number of shift to be done |
| * @retval None |
| */ |
| #define __HAL_ADC_Value_Shift_left(_Value_, _Shift_) ((_Value_) << (_Shift_)) |
| |
| |
| /** |
| * @brief Enable the ADC end of conversion interrupt. |
| * @param __HANDLE__ ADC handle. |
| * @param __INTERRUPT__ ADC Interrupt. |
| * @retval None |
| */ |
| #define __HAL_ADC_ENABLE_IT(__HANDLE__, __INTERRUPT__) \ |
| (((__HANDLE__)->Instance->IER) |= (__INTERRUPT__)) |
| |
| /** |
| * @brief Disable the ADC end of conversion interrupt. |
| * @param __HANDLE__ ADC handle. |
| * @param __INTERRUPT__ ADC interrupt. |
| * @retval None |
| */ |
| #define __HAL_ADC_DISABLE_IT(__HANDLE__, __INTERRUPT__) \ |
| (((__HANDLE__)->Instance->IER) &= ~(__INTERRUPT__)) |
| |
| /** @brief Checks if the specified ADC interrupt source is enabled or disabled. |
| * @param __HANDLE__ ADC handle |
| * @param __INTERRUPT__ ADC interrupt source to check |
| * @arg ... |
| * @arg ... |
| * @retval State of interruption (TRUE or FALSE) |
| */ |
| #define __HAL_ADC_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) \ |
| (((__HANDLE__)->Instance->IER & (__INTERRUPT__)) == (__INTERRUPT__)) |
| |
| /** |
| * @brief Clear the ADC's pending flags |
| * @param __HANDLE__ ADC handle. |
| * @param __FLAG__ ADC flag. |
| * @retval None |
| */ |
| /* Note: bit cleared bit by writing 1 */ |
| #define __HAL_ADC_CLEAR_FLAG(__HANDLE__, __FLAG__) \ |
| (((__HANDLE__)->Instance->ISR) = (__FLAG__)) |
| |
| /** |
| * @brief Get the selected ADC's flag status. |
| * @param __HANDLE__ ADC handle. |
| * @param __FLAG__ ADC flag. |
| * @retval None |
| */ |
| #define __HAL_ADC_GET_FLAG(__HANDLE__, __FLAG__) \ |
| ((((__HANDLE__)->Instance->ISR) & (__FLAG__)) == (__FLAG__)) |
| |
| |
| /** |
| * @brief Simultaneously clears and sets specific bits of the handle State |
| * @note: ADC_STATE_CLR_SET() macro is merely aliased to generic macro MODIFY_REG(), |
| * the first parameter is the ADC handle State, the second parameter is the |
| * bit field to clear, the third and last parameter is the bit field to set. |
| * @retval None |
| */ |
| #define ADC_STATE_CLR_SET MODIFY_REG |
| |
| /** |
| * @brief Clear ADC error code (set it to error code: "no error") |
| * @param __HANDLE__ ADC handle |
| * @retval None |
| */ |
| #define ADC_CLEAR_ERRORCODE(__HANDLE__) \ |
| ((__HANDLE__)->ErrorCode = HAL_ADC_ERROR_NONE) |
| |
| |
| /** |
| * @brief Configuration of ADC clock & prescaler: clock source PCLK or Asynchronous with selectable prescaler |
| * @param __HANDLE__ ADC handle |
| * @retval None |
| */ |
| |
| #define __HAL_ADC_CLOCK_PRESCALER(__HANDLE__) \ |
| do{ \ |
| if ((((__HANDLE__)->Init.ClockPrescaler) == ADC_CLOCK_SYNC_PCLK_DIV1) || \ |
| (((__HANDLE__)->Init.ClockPrescaler) == ADC_CLOCK_SYNC_PCLK_DIV2) || \ |
| (((__HANDLE__)->Init.ClockPrescaler) == ADC_CLOCK_SYNC_PCLK_DIV4)) \ |
| { \ |
| (__HANDLE__)->Instance->CFGR2 &= ~(ADC_CFGR2_CKMODE); \ |
| (__HANDLE__)->Instance->CFGR2 |= (__HANDLE__)->Init.ClockPrescaler; \ |
| } \ |
| else \ |
| { \ |
| /* CKMOD bits must be reset */ \ |
| (__HANDLE__)->Instance->CFGR2 &= ~(ADC_CFGR2_CKMODE); \ |
| ADC->CCR &= ~(ADC_CCR_PRESC); \ |
| ADC->CCR |= (__HANDLE__)->Init.ClockPrescaler; \ |
| } \ |
| } while(0) |
| |
| |
| #define IS_ADC_CLOCKPRESCALER(ADC_CLOCK) (((ADC_CLOCK) == ADC_CLOCK_ASYNC_DIV1) ||\ |
| ((ADC_CLOCK) == ADC_CLOCK_SYNC_PCLK_DIV1) ||\ |
| ((ADC_CLOCK) == ADC_CLOCK_SYNC_PCLK_DIV2) ||\ |
| ((ADC_CLOCK) == ADC_CLOCK_SYNC_PCLK_DIV4) ||\ |
| ((ADC_CLOCK) == ADC_CLOCK_ASYNC_DIV1 ) ||\ |
| ((ADC_CLOCK) == ADC_CLOCK_ASYNC_DIV2 ) ||\ |
| ((ADC_CLOCK) == ADC_CLOCK_ASYNC_DIV4 ) ||\ |
| ((ADC_CLOCK) == ADC_CLOCK_ASYNC_DIV6 ) ||\ |
| ((ADC_CLOCK) == ADC_CLOCK_ASYNC_DIV8 ) ||\ |
| ((ADC_CLOCK) == ADC_CLOCK_ASYNC_DIV10 ) ||\ |
| ((ADC_CLOCK) == ADC_CLOCK_ASYNC_DIV12 ) ||\ |
| ((ADC_CLOCK) == ADC_CLOCK_ASYNC_DIV16 ) ||\ |
| ((ADC_CLOCK) == ADC_CLOCK_ASYNC_DIV32 ) ||\ |
| ((ADC_CLOCK) == ADC_CLOCK_ASYNC_DIV64 ) ||\ |
| ((ADC_CLOCK) == ADC_CLOCK_ASYNC_DIV128 ) ||\ |
| ((ADC_CLOCK) == ADC_CLOCK_ASYNC_DIV256)) |
| |
| #define IS_ADC_RESOLUTION(RESOLUTION) (((RESOLUTION) == ADC_RESOLUTION_12B) || \ |
| ((RESOLUTION) == ADC_RESOLUTION_10B) || \ |
| ((RESOLUTION) == ADC_RESOLUTION_8B) || \ |
| ((RESOLUTION) == ADC_RESOLUTION_6B)) |
| |
| #define IS_ADC_RESOLUTION_8_6_BITS(RESOLUTION) (((RESOLUTION) == ADC_RESOLUTION_8B) || \ |
| ((RESOLUTION) == ADC_RESOLUTION_6B)) |
| |
| #define IS_ADC_DATA_ALIGN(ALIGN) (((ALIGN) == ADC_DATAALIGN_RIGHT) || \ |
| ((ALIGN) == ADC_DATAALIGN_LEFT)) |
| |
| #define IS_ADC_EXTTRIG_EDGE(EDGE) (((EDGE) == ADC_EXTERNALTRIGCONVEDGE_NONE) || \ |
| ((EDGE) == ADC_EXTERNALTRIGCONVEDGE_RISING) || \ |
| ((EDGE) == ADC_EXTERNALTRIGCONVEDGE_FALLING) || \ |
| ((EDGE) == ADC_EXTERNALTRIGCONVEDGE_RISINGFALLING)) |
| |
| #define IS_ADC_EOC_SELECTION(EOC_SELECTION) (((EOC_SELECTION) == ADC_EOC_SINGLE_CONV) || \ |
| ((EOC_SELECTION) == ADC_EOC_SEQ_CONV)) |
| |
| #define IS_ADC_OVERRUN(OVR) (((OVR) == ADC_OVR_DATA_PRESERVED) || \ |
| ((OVR) == ADC_OVR_DATA_OVERWRITTEN)) |
| |
| #define IS_ADC_RANK(WATCHDOG) (((WATCHDOG) == ADC_RANK_CHANNEL_NUMBER) || \ |
| ((WATCHDOG) == ADC_RANK_NONE)) |
| |
| #if defined (ADC_CHANNEL_VLCD) |
| #define IS_ADC_CHANNEL(CHANNEL) (((CHANNEL) == ADC_CHANNEL_0) || \ |
| ((CHANNEL) == ADC_CHANNEL_1) || \ |
| ((CHANNEL) == ADC_CHANNEL_2) || \ |
| ((CHANNEL) == ADC_CHANNEL_3) || \ |
| ((CHANNEL) == ADC_CHANNEL_4) || \ |
| ((CHANNEL) == ADC_CHANNEL_5) || \ |
| ((CHANNEL) == ADC_CHANNEL_6) || \ |
| ((CHANNEL) == ADC_CHANNEL_7) || \ |
| ((CHANNEL) == ADC_CHANNEL_8) || \ |
| ((CHANNEL) == ADC_CHANNEL_9) || \ |
| ((CHANNEL) == ADC_CHANNEL_10) || \ |
| ((CHANNEL) == ADC_CHANNEL_11) || \ |
| ((CHANNEL) == ADC_CHANNEL_12) || \ |
| ((CHANNEL) == ADC_CHANNEL_13) || \ |
| ((CHANNEL) == ADC_CHANNEL_14) || \ |
| ((CHANNEL) == ADC_CHANNEL_15) || \ |
| ((CHANNEL) == ADC_CHANNEL_TEMPSENSOR) || \ |
| ((CHANNEL) == ADC_CHANNEL_VREFINT) || \ |
| ((CHANNEL) == ADC_CHANNEL_VLCD)) |
| #elif defined (ADC_CHANNEL_TEMPSENSOR) |
| #define IS_ADC_CHANNEL(CHANNEL) (((CHANNEL) == ADC_CHANNEL_0) || \ |
| ((CHANNEL) == ADC_CHANNEL_1) || \ |
| ((CHANNEL) == ADC_CHANNEL_2) || \ |
| ((CHANNEL) == ADC_CHANNEL_3) || \ |
| ((CHANNEL) == ADC_CHANNEL_4) || \ |
| ((CHANNEL) == ADC_CHANNEL_5) || \ |
| ((CHANNEL) == ADC_CHANNEL_6) || \ |
| ((CHANNEL) == ADC_CHANNEL_7) || \ |
| ((CHANNEL) == ADC_CHANNEL_8) || \ |
| ((CHANNEL) == ADC_CHANNEL_9) || \ |
| ((CHANNEL) == ADC_CHANNEL_10) || \ |
| ((CHANNEL) == ADC_CHANNEL_11) || \ |
| ((CHANNEL) == ADC_CHANNEL_12) || \ |
| ((CHANNEL) == ADC_CHANNEL_13) || \ |
| ((CHANNEL) == ADC_CHANNEL_14) || \ |
| ((CHANNEL) == ADC_CHANNEL_15) || \ |
| ((CHANNEL) == ADC_CHANNEL_TEMPSENSOR) || \ |
| ((CHANNEL) == ADC_CHANNEL_VREFINT)) |
| #else |
| #define IS_ADC_CHANNEL(CHANNEL) (((CHANNEL) == ADC_CHANNEL_0) || \ |
| ((CHANNEL) == ADC_CHANNEL_1) || \ |
| ((CHANNEL) == ADC_CHANNEL_2) || \ |
| ((CHANNEL) == ADC_CHANNEL_3) || \ |
| ((CHANNEL) == ADC_CHANNEL_4) || \ |
| ((CHANNEL) == ADC_CHANNEL_5) || \ |
| ((CHANNEL) == ADC_CHANNEL_6) || \ |
| ((CHANNEL) == ADC_CHANNEL_7) || \ |
| ((CHANNEL) == ADC_CHANNEL_8) || \ |
| ((CHANNEL) == ADC_CHANNEL_9) || \ |
| ((CHANNEL) == ADC_CHANNEL_10) || \ |
| ((CHANNEL) == ADC_CHANNEL_11) || \ |
| ((CHANNEL) == ADC_CHANNEL_12) || \ |
| ((CHANNEL) == ADC_CHANNEL_13) || \ |
| ((CHANNEL) == ADC_CHANNEL_14) || \ |
| ((CHANNEL) == ADC_CHANNEL_15) || \ |
| ((CHANNEL) == ADC_CHANNEL_VREFINT)) |
| #endif |
| |
| #define IS_ADC_SAMPLE_TIME(TIME) (((TIME) == ADC_SAMPLETIME_1CYCLE_5 ) || \ |
| ((TIME) == ADC_SAMPLETIME_3CYCLES_5 ) || \ |
| ((TIME) == ADC_SAMPLETIME_7CYCLES_5 ) || \ |
| ((TIME) == ADC_SAMPLETIME_12CYCLES_5 ) || \ |
| ((TIME) == ADC_SAMPLETIME_19CYCLES_5 ) || \ |
| ((TIME) == ADC_SAMPLETIME_39CYCLES_5 ) || \ |
| ((TIME) == ADC_SAMPLETIME_79CYCLES_5 ) || \ |
| ((TIME) == ADC_SAMPLETIME_160CYCLES_5)) |
| |
| #define IS_ADC_SCAN_MODE(SCAN_MODE) (((SCAN_MODE) == ADC_SCAN_DIRECTION_FORWARD) || \ |
| ((SCAN_MODE) == ADC_SCAN_DIRECTION_BACKWARD)) |
| |
| #define IS_ADC_OVERSAMPLING_RATIO(RATIO) (((RATIO) == ADC_OVERSAMPLING_RATIO_2 ) || \ |
| ((RATIO) == ADC_OVERSAMPLING_RATIO_4 ) || \ |
| ((RATIO) == ADC_OVERSAMPLING_RATIO_8 ) || \ |
| ((RATIO) == ADC_OVERSAMPLING_RATIO_16 ) || \ |
| ((RATIO) == ADC_OVERSAMPLING_RATIO_32 ) || \ |
| ((RATIO) == ADC_OVERSAMPLING_RATIO_64 ) || \ |
| ((RATIO) == ADC_OVERSAMPLING_RATIO_128 ) || \ |
| ((RATIO) == ADC_OVERSAMPLING_RATIO_256 )) |
| |
| #define IS_ADC_RIGHT_BIT_SHIFT(SHIFT) (((SHIFT) == ADC_RIGHTBITSHIFT_NONE) || \ |
| ((SHIFT) == ADC_RIGHTBITSHIFT_1 ) || \ |
| ((SHIFT) == ADC_RIGHTBITSHIFT_2 ) || \ |
| ((SHIFT) == ADC_RIGHTBITSHIFT_3 ) || \ |
| ((SHIFT) == ADC_RIGHTBITSHIFT_4 ) || \ |
| ((SHIFT) == ADC_RIGHTBITSHIFT_5 ) || \ |
| ((SHIFT) == ADC_RIGHTBITSHIFT_6 ) || \ |
| ((SHIFT) == ADC_RIGHTBITSHIFT_7 ) || \ |
| ((SHIFT) == ADC_RIGHTBITSHIFT_8 )) |
| |
| #define IS_ADC_TRIGGERED_OVERSAMPLING_MODE(MODE) (((MODE) == ADC_TRIGGEREDMODE_SINGLE_TRIGGER) || \ |
| ((MODE) == ADC_TRIGGEREDMODE_MULTI_TRIGGER) ) |
| |
| #define IS_ADC_ANALOG_WATCHDOG_MODE(WATCHDOG) (((WATCHDOG) == ADC_ANALOGWATCHDOG_NONE ) || \ |
| ((WATCHDOG) == ADC_ANALOGWATCHDOG_SINGLE_REG) || \ |
| ((WATCHDOG) == ADC_ANALOGWATCHDOG_ALL_REG )) |
| |
| #define IS_ADC_CONVERSION_GROUP(CONVERSION) ((CONVERSION) == ADC_REGULAR_GROUP) |
| |
| #define IS_ADC_EVENT_TYPE(EVENT) (((EVENT) == ADC_AWD_EVENT) || \ |
| ((EVENT) == ADC_OVR_EVENT)) |
| |
| |
| /** @defgroup ADC_range_verification ADC Range Verification |
| * in function of ADC resolution selected (12, 10, 8 or 6 bits) |
| * @{ |
| */ |
| #define IS_ADC_RANGE(RESOLUTION, ADC_VALUE) \ |
| ((((RESOLUTION) == ADC_RESOLUTION_12B) && ((ADC_VALUE) <= ((uint32_t)0x0FFFU))) || \ |
| (((RESOLUTION) == ADC_RESOLUTION_10B) && ((ADC_VALUE) <= ((uint32_t)0x03FFU))) || \ |
| (((RESOLUTION) == ADC_RESOLUTION_8B) && ((ADC_VALUE) <= ((uint32_t)0x00FFU))) || \ |
| (((RESOLUTION) == ADC_RESOLUTION_6B) && ((ADC_VALUE) <= ((uint32_t)0x003FU)))) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup ADC_regular_nb_conv_verification ADC Regular Nb Conversion Verification |
| * @{ |
| */ |
| #define IS_ADC_REGULAR_NB_CONV(LENGTH) (((LENGTH) >= ((uint32_t)1U)) && ((LENGTH) <= ((uint32_t)16U))) |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Include ADC HAL Extended module */ |
| #include "stm32l0xx_hal_adc_ex.h" |
| |
| /* Exported functions --------------------------------------------------------*/ |
| /** @addtogroup ADC_Exported_Functions |
| * @{ |
| */ |
| |
| /** @addtogroup ADC_Exported_Functions_Group1 |
| * @brief Initialization and Configuration functions |
| * @{ |
| */ |
| /* Initialization and de-initialization functions ****************************/ |
| HAL_StatusTypeDef HAL_ADC_Init(ADC_HandleTypeDef* hadc); |
| HAL_StatusTypeDef HAL_ADC_DeInit(ADC_HandleTypeDef *hadc); |
| void HAL_ADC_MspInit(ADC_HandleTypeDef* hadc); |
| void HAL_ADC_MspDeInit(ADC_HandleTypeDef* hadc); |
| |
| #if (USE_HAL_ADC_REGISTER_CALLBACKS == 1) |
| /* Callbacks Register/UnRegister functions ***********************************/ |
| HAL_StatusTypeDef HAL_ADC_RegisterCallback(ADC_HandleTypeDef *hadc, HAL_ADC_CallbackIDTypeDef CallbackID, pADC_CallbackTypeDef pCallback); |
| HAL_StatusTypeDef HAL_ADC_UnRegisterCallback(ADC_HandleTypeDef *hadc, HAL_ADC_CallbackIDTypeDef CallbackID); |
| #endif /* USE_HAL_ADC_REGISTER_CALLBACKS */ |
| |
| /** |
| * @} |
| */ |
| |
| /** @addtogroup ADC_Exported_Functions_Group2 |
| * @brief IO operation functions |
| * @{ |
| */ |
| /* IO operation functions *****************************************************/ |
| |
| /* Blocking mode: Polling */ |
| HAL_StatusTypeDef HAL_ADC_Start(ADC_HandleTypeDef* hadc); |
| HAL_StatusTypeDef HAL_ADC_Stop(ADC_HandleTypeDef* hadc); |
| HAL_StatusTypeDef HAL_ADC_PollForConversion(ADC_HandleTypeDef* hadc, uint32_t Timeout); |
| HAL_StatusTypeDef HAL_ADC_PollForEvent(ADC_HandleTypeDef* hadc, uint32_t EventType, uint32_t Timeout); |
| |
| /* Non-blocking mode: Interruption */ |
| HAL_StatusTypeDef HAL_ADC_Start_IT(ADC_HandleTypeDef* hadc); |
| HAL_StatusTypeDef HAL_ADC_Stop_IT(ADC_HandleTypeDef* hadc); |
| |
| /* Non-blocking mode: DMA */ |
| HAL_StatusTypeDef HAL_ADC_Start_DMA(ADC_HandleTypeDef* hadc, uint32_t* pData, uint32_t Length); |
| HAL_StatusTypeDef HAL_ADC_Stop_DMA(ADC_HandleTypeDef* hadc); |
| |
| /* ADC retrieve conversion value intended to be used with polling or interruption */ |
| uint32_t HAL_ADC_GetValue(ADC_HandleTypeDef* hadc); |
| |
| /* ADC IRQHandler and Callbacks used in non-blocking modes (Interruption and DMA) */ |
| void HAL_ADC_IRQHandler(ADC_HandleTypeDef* hadc); |
| void HAL_ADC_ConvCpltCallback(ADC_HandleTypeDef* hadc); |
| void HAL_ADC_ConvHalfCpltCallback(ADC_HandleTypeDef* hadc); |
| void HAL_ADC_LevelOutOfWindowCallback(ADC_HandleTypeDef* hadc); |
| void HAL_ADC_ErrorCallback(ADC_HandleTypeDef *hadc); |
| /** |
| * @} |
| */ |
| |
| /** @addtogroup ADC_Exported_Functions_Group3 Peripheral Control functions |
| * @brief Peripheral Control functions |
| * @{ |
| */ |
| /* Peripheral Control functions ***********************************************/ |
| HAL_StatusTypeDef HAL_ADC_ConfigChannel(ADC_HandleTypeDef* hadc, ADC_ChannelConfTypeDef* sConfig); |
| HAL_StatusTypeDef HAL_ADC_AnalogWDGConfig(ADC_HandleTypeDef* hadc, ADC_AnalogWDGConfTypeDef* AnalogWDGConfig); |
| /** |
| * @} |
| */ |
| |
| /* Peripheral State functions *************************************************/ |
| /** @addtogroup ADC_Exported_Functions_Group4 |
| * @{ |
| */ |
| uint32_t HAL_ADC_GetState(ADC_HandleTypeDef* hadc); |
| uint32_t HAL_ADC_GetError(ADC_HandleTypeDef *hadc); |
| /** |
| * @} |
| */ |
| |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| #ifdef __cplusplus |
| } |
| #endif |
| |
| |
| #endif /*__STM32L0xx_HAL_ADC_H */ |
| |
| /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |
