| config UART_STELLARIS |
| bool "Stellaris serial driver" |
| default n |
| select SERIAL_HAS_DRIVER |
| help |
| This option enables the Stellaris serial driver. |
| This specific driver can be used for the serial hardware |
| available at the Texas Instrument LM3S6965 platform. |
| |
| # ---------- Port 0 ---------- |
| |
| menuconfig UART_STELLARIS_PORT_0 |
| bool "Enable Stellaris UART Port 0" |
| default n |
| depends on UART_STELLARIS |
| help |
| This tells the driver to configure the UART port at boot, depending on |
| the additional configure options below. |
| |
| config UART_STELLARIS_PORT_0_NAME |
| string "Port 0 Device Name" |
| default "UART_0" |
| depends on UART_STELLARIS_PORT_0 |
| help |
| This is the device name for UART, and is included in the device |
| struct. |
| |
| config UART_STELLARIS_PORT_0_BASE_ADDR |
| hex |
| prompt "Port 0 Base Address" |
| default 0x00000000 |
| depends on UART_STELLARIS_PORT_0 |
| help |
| The base address of UART port. |
| |
| Leave this at 0x00000000 to skip initialization at boot. |
| |
| config UART_STELLARIS_PORT_0_IRQ |
| int "Port 0 Interrupt Vector" |
| default 0 |
| depends on UART_STELLARIS_PORT_0 |
| help |
| The interrupt vector for UART port. This is used for interrupt driven |
| transfers. |
| |
| config UART_STELLARIS_PORT_0_IRQ_PRI |
| int "Port 0 Interrupt Priority" |
| default 0 |
| depends on UART_STELLARIS_PORT_0 |
| help |
| The interrupt priority for UART port. |
| |
| config UART_STELLARIS_PORT_0_BAUD_RATE |
| int "Port 0 Baud Rate" |
| default 0 |
| depends on UART_STELLARIS_PORT_0 |
| help |
| The baud rate for UART port to be set to at boot. |
| |
| Leave at 0 to skip initialization. |
| |
| config UART_STELLARIS_PORT_0_CLK_FREQ |
| int "Port 0 Clock Frequency" |
| default 0 |
| depends on UART_STELLARIS_PORT_0 |
| help |
| The clock frequency for UART port. |
| |
| # ---------- Port 1 ---------- |
| |
| menuconfig UART_STELLARIS_PORT_1 |
| bool "Enable Stellaris UART Port 1" |
| default n |
| depends on UART_STELLARIS |
| help |
| This tells the driver to configure the UART port at boot, depending on |
| the additional configure options below. |
| |
| config UART_STELLARIS_PORT_1_NAME |
| string "Port 1 Device Name" |
| default "UART_1" |
| depends on UART_STELLARIS_PORT_1 |
| help |
| This is the device name for UART, and is included in the device |
| struct. |
| |
| config UART_STELLARIS_PORT_1_BASE_ADDR |
| hex |
| prompt "Port 1 Base Address" |
| default 0x00000000 |
| depends on UART_STELLARIS_PORT_1 |
| help |
| The base address of UART port. |
| |
| Leave this at 0x00000000 to skip initialization at boot. |
| |
| config UART_STELLARIS_PORT_1_IRQ |
| int "Port 1 Interrupt Vector" |
| default 0 |
| depends on UART_STELLARIS_PORT_1 |
| help |
| The interrupt vector for UART port. This is used for interrupt driven |
| transfers. |
| |
| config UART_STELLARIS_PORT_1_IRQ_PRI |
| int "Port 1 Interrupt Priority" |
| default 0 |
| depends on UART_STELLARIS_PORT_1 |
| help |
| The interrupt priority for UART port. |
| |
| config UART_STELLARIS_PORT_1_BAUD_RATE |
| int "Port 1 Baud Rate" |
| default 0 |
| depends on UART_STELLARIS_PORT_1 |
| help |
| The baud rate for UART port to be set to at boot. |
| |
| Leave at 0 to skip initialization. |
| |
| config UART_STELLARIS_PORT_1_CLK_FREQ |
| int "Port 1 Clock Frequency" |
| default 0 |
| depends on UART_STELLARIS_PORT_1 |
| help |
| The clock frequency for UART port. |
| |
| # ---------- Port 2 ---------- |
| |
| menuconfig UART_STELLARIS_PORT_2 |
| bool "Enable Stellaris UART Port 2" |
| default n |
| depends on UART_STELLARIS |
| help |
| This tells the driver to configure the UART port at boot, depending on |
| the additional configure options below. |
| |
| config UART_STELLARIS_PORT_2_NAME |
| string "Port 2 Device Name" |
| default "UART_2" |
| depends on UART_STELLARIS_PORT_2 |
| help |
| This is the device name for UART, and is included in the device |
| struct. |
| |
| config UART_STELLARIS_PORT_2_BASE_ADDR |
| hex |
| prompt "Port 2 Base Address" |
| default 0x00000000 |
| depends on UART_STELLARIS_PORT_2 |
| help |
| The base address of UART port. |
| |
| Leave this at 0x00000000 to skip initialization at boot. |
| |
| config UART_STELLARIS_PORT_2_IRQ |
| int "Port 2 Interrupt Vector" |
| default 0 |
| depends on UART_STELLARIS_PORT_2 |
| help |
| The interrupt vector for UART port. This is used for interrupt driven |
| transfers. |
| |
| config UART_STELLARIS_PORT_2_IRQ_PRI |
| int "Port 2 Interrupt Priority" |
| default 0 |
| depends on UART_STELLARIS_PORT_2 |
| help |
| The interrupt priority for UART port. |
| |
| config UART_STELLARIS_PORT_2_BAUD_RATE |
| int "Port 2 Baud Rate" |
| default 0 |
| depends on UART_STELLARIS_PORT_2 |
| help |
| The baud rate for UART port to be set to at boot. |
| |
| Leave at 0 to skip initialization. |
| |
| config UART_STELLARIS_PORT_2_CLK_FREQ |
| int "Port 2 Clock Frequency" |
| default 0 |
| depends on UART_STELLARIS_PORT_2 |
| help |
| The clock frequency for UART port. |
