| /* |
| * Copyright (c) 2022 Laird Connectivity |
| * |
| * SPDX-License-Identifier: Apache-2.0 |
| */ |
| |
| /dts-v1/; |
| #include <nordic/nrf52840_qiaa.dtsi> |
| #include "mg100-pinctrl.dtsi" |
| #include <zephyr/dt-bindings/input/input-event-codes.h> |
| |
| / { |
| model = "MG100"; |
| compatible = "lairdconnect,mg100"; |
| |
| chosen { |
| zephyr,console = &uart0; |
| zephyr,shell-uart = &uart0; |
| zephyr,uart-mcumgr = &uart0; |
| zephyr,bt-mon-uart = &uart0; |
| zephyr,sram = &sram0; |
| zephyr,flash = &flash0; |
| zephyr,code-partition = &slot0_partition; |
| zephyr,ieee802154 = &ieee802154; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| led1: led_1 { |
| gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; |
| label = "Red LED"; |
| }; |
| led2: led_2 { |
| gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; |
| label = "Blue LED"; |
| }; |
| led3: led_3 { |
| gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; |
| label = "Green LED"; |
| }; |
| }; |
| |
| buttons { |
| compatible = "gpio-keys"; |
| button1: button_1 { |
| gpios = <&gpio0 3 (GPIO_PULL_UP | GPIO_ACTIVE_LOW)>; |
| label = "Push button switch"; |
| zephyr,code = <INPUT_KEY_0>; |
| }; |
| }; |
| |
| en-sd-switch { |
| compatible = "regulator-fixed"; |
| regulator-name = "en_sd_switch"; |
| enable-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>; |
| regulator-boot-on; |
| }; |
| |
| /* These aliases are provided for compatibility with samples */ |
| aliases { |
| led0 = &led1; |
| led1 = &led2; |
| led2 = &led3; |
| sw0 = &button1; |
| mcuboot-button0 = &button1; |
| mcuboot-led0 = &led1; |
| watchdog0 = &wdt0; |
| spi-flash0 = &mx25r64; |
| }; |
| }; |
| |
| &adc { |
| status = "okay"; |
| }; |
| |
| &uicr { |
| gpio-as-nreset; |
| }; |
| |
| &gpiote { |
| status = "okay"; |
| }; |
| |
| &gpio0 { |
| status = "okay"; |
| }; |
| |
| &gpio1 { |
| status = "okay"; |
| }; |
| |
| &uart0 { |
| compatible = "nordic,nrf-uart"; |
| status = "okay"; |
| current-speed = <115200>; |
| pinctrl-0 = <&uart0_default>; |
| pinctrl-1 = <&uart0_sleep>; |
| pinctrl-names = "default", "sleep"; |
| }; |
| |
| &uart1 { |
| compatible = "nordic,nrf-uarte"; |
| status = "okay"; |
| current-speed = <115200>; |
| hw-flow-control; |
| pinctrl-0 = <&uart1_default>; |
| pinctrl-1 = <&uart1_sleep>; |
| pinctrl-names = "default", "sleep"; |
| hl7800: hl7800 { |
| compatible = "swir,hl7800"; |
| status = "okay"; |
| mdm-reset-gpios = <&gpio1 15 (GPIO_OPEN_DRAIN | GPIO_ACTIVE_LOW)>; |
| mdm-wake-gpios = <&gpio1 13 (GPIO_OPEN_SOURCE | GPIO_ACTIVE_HIGH)>; |
| mdm-pwr-on-gpios = <&gpio1 2 (GPIO_OPEN_DRAIN | GPIO_ACTIVE_LOW)>; |
| mdm-fast-shutd-gpios = <&gpio1 14 (GPIO_OPEN_DRAIN | GPIO_ACTIVE_LOW)>; |
| mdm-vgpio-gpios = <&gpio1 11 0>; |
| mdm-uart-dsr-gpios = <&gpio0 25 0>; |
| mdm-uart-cts-gpios = <&gpio0 15 0>; |
| mdm-gpio6-gpios = <&gpio1 12 0>; |
| }; |
| }; |
| |
| &i2c0 { |
| compatible = "nordic,nrf-twim"; |
| status = "okay"; |
| |
| pinctrl-0 = <&i2c0_default>; |
| pinctrl-1 = <&i2c0_sleep>; |
| pinctrl-names = "default", "sleep"; |
| lis2dh@19 { |
| compatible = "st,lis3dh", "st,lis2dh"; |
| status = "okay"; |
| reg = <0x19>; |
| irq-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; |
| anym-on-int1; |
| }; |
| }; |
| |
| &spi2 { |
| compatible = "nordic,nrf-spim"; |
| status = "okay"; |
| pinctrl-0 = <&spi2_default>; |
| pinctrl-1 = <&spi2_sleep>; |
| pinctrl-names = "default", "sleep"; |
| cs-gpios = <&gpio0 29 GPIO_ACTIVE_LOW>; |
| sdhc0: sdhc@0 { |
| compatible = "zephyr,sdhc-spi-slot"; |
| status = "okay"; |
| reg = <0>; |
| spi-max-frequency = <8000000>; |
| mmc { |
| compatible = "zephyr,sdmmc-disk"; |
| status = "okay"; |
| }; |
| }; |
| }; |
| |
| &qspi { |
| status = "okay"; |
| pinctrl-0 = <&qspi_default>; |
| pinctrl-1 = <&qspi_sleep>; |
| pinctrl-names = "default", "sleep"; |
| mx25r64: mx25r6435f@0 { |
| compatible = "nordic,qspi-nor"; |
| reg = <0>; |
| writeoc = "pp4io"; |
| readoc = "read4io"; |
| sck-frequency = <8000000>; |
| jedec-id = [ c2 28 17 ]; |
| size = <67108864>; |
| has-dpd; |
| t-enter-dpd = <10000>; |
| t-exit-dpd = <35000>; |
| }; |
| }; |
| |
| &ieee802154 { |
| status = "okay"; |
| }; |
| |
| &flash0 { |
| partitions { |
| compatible = "fixed-partitions"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| /* 96K */ |
| boot_partition: partition@0 { |
| label = "mcuboot"; |
| reg = <0x00000000 0x00018000>; |
| }; |
| /* 896K */ |
| slot0_partition: partition@18000 { |
| label = "image-0"; |
| reg = <0x00018000 0x000E0000>; |
| }; |
| |
| /* |
| * The flash starting at 0x000f8000 and ending at |
| * 0x000fffff is reserved for use by the application. |
| */ |
| |
| /* |
| * Storage partition will be used by FCB/NVS |
| * if enabled. 32K |
| */ |
| storage_partition: partition@f8000 { |
| label = "storage"; |
| reg = <0x000f8000 0x00008000>; |
| }; |
| }; |
| }; |
| |
| &mx25r64 { |
| partitions { |
| compatible = "fixed-partitions"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| /* 896K */ |
| slot1_partition: partition@0 { |
| label = "image-1"; |
| reg = <0x00000000 0x000E0000>; |
| }; |
| /* 128K */ |
| scratch_partition: partition@E0000 { |
| label = "image-scratch"; |
| reg = <0x000E0000 0x00020000>; |
| }; |
| /* 7MB */ |
| lfs_partition: partition@100000 { |
| label = "lfs_storage"; |
| reg = <0x00100000 0x00700000>; |
| }; |
| }; |
| }; |