| /* |
| * Copyright 2022, NXP |
| * |
| * SPDX-License-Identifier: Apache-2.0 |
| */ |
| |
| /dts-v1/; |
| |
| #include <nxp/nxp_rt5xx.dtsi> |
| #include <zephyr/dt-bindings/regulator/pca9420.h> |
| |
| #include "mimxrt595_evk_cm33-pinctrl.dtsi" |
| |
| / { |
| model = "NXP MIMXRT595-EVK board"; |
| compatible = "nxp,mimxrt595"; |
| |
| aliases { |
| sw0 = &user_button_1; |
| sw1 = &user_button_2; |
| led0 = &green_led; |
| led1 = &blue_led; |
| led2 = &red_led; |
| usart-0 = &flexcomm0; |
| watchdog0 = &wwdt0; |
| magn0 = &fxos8700; |
| accel0 = &fxos8700; |
| }; |
| |
| chosen { |
| zephyr,flash-controller = &mx25um51345g; |
| zephyr,flash = &mx25um51345g; |
| zephyr,code-partition = &slot0_partition; |
| zephyr,sram = &sram0; |
| zephyr,console = &flexcomm0; |
| zephyr,shell-uart = &flexcomm0; |
| }; |
| |
| gpio_keys { |
| compatible = "gpio-keys"; |
| user_button_1: button_0 { |
| label = "User SW1"; |
| gpios = <&gpio0 25 GPIO_ACTIVE_LOW>; |
| }; |
| user_button_2: button_1 { |
| label = "User SW2"; |
| gpios = <&gpio0 10 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| green_led: led_1 { |
| gpios = <&gpio1 0 0>; |
| label = "User LED_GREEN"; |
| }; |
| blue_led: led_2 { |
| gpios = <&gpio3 17 0>; |
| label = "User LED_BLUE"; |
| }; |
| red_led: led_3 { |
| gpios = <&gpio0 14 0>; |
| label = "User LED_RED"; |
| }; |
| }; |
| |
| arduino_header: arduino-connector { |
| compatible = "arduino-header-r3"; |
| #gpio-cells = <2>; |
| gpio-map-mask = <0xffffffff 0xffffffc0>; |
| gpio-map-pass-thru = <0 0x3f>; |
| gpio-map = <0 0 &gpio0 5 0>, /* A0 */ |
| <1 0 &gpio0 6 0>, /* A1 */ |
| <2 0 &gpio0 19 0>, /* A2 */ |
| <3 0 &gpio0 13 0>, /* A3 */ |
| <4 0 &gpio4 22 0>, /* A4 */ |
| <5 0 &gpio4 21 0>, /* A5 */ |
| <6 0 &gpio4 31 0>, /* D0 */ |
| <7 0 &gpio4 30 0>, /* D1 */ |
| <8 0 &gpio4 20 0>, /* D2 */ |
| <9 0 &gpio4 23 0>, /* D3 */ |
| <10 0 &gpio4 24 0>, /* D4 */ |
| <11 0 &gpio4 25 0>, /* D5 */ |
| <12 0 &gpio4 26 0>, /* D6 */ |
| <13 0 &gpio4 27 0>, /* D7 */ |
| <14 0 &gpio4 28 0>, /* D8 */ |
| <15 0 &gpio4 29 0>, /* D9 */ |
| <16 0 &gpio5 0 0>, /* D10 */ |
| <17 0 &gpio5 1 0>, /* D11 */ |
| <18 0 &gpio5 2 0>, /* D12 */ |
| <19 0 &gpio5 3 0>, /* D13 */ |
| <20 0 &gpio4 22 0>, /* D14 */ |
| <21 0 &gpio4 21 0>; /* D15 */ |
| }; |
| }; |
| |
| /* |
| * RT595 EVK board uses OS timer as the kernel timer |
| * In case we need to switch to SYSTICK timer, then |
| * replace &os_timer with &systick |
| */ |
| &os_timer { |
| status = "okay"; |
| }; |
| |
| &rtc { |
| status = "okay"; |
| }; |
| |
| &flexcomm0 { |
| compatible = "nxp,lpc-usart"; |
| status = "okay"; |
| current-speed = <115200>; |
| pinctrl-0 = <&pinmux_flexcomm0_usart>; |
| pinctrl-names = "default"; |
| }; |
| |
| arduino_i2c: &flexcomm4 { |
| compatible = "nxp,lpc-i2c"; |
| status = "okay"; |
| clock-frequency = <I2C_BITRATE_FAST>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| pinctrl-0 = <&pinmux_flexcomm4_i2c>; |
| pinctrl-names = "default"; |
| |
| fxos8700: fxos8700@1e { |
| compatible = "nxp,fxos8700"; |
| reg = <0x1e>; |
| int1-gpios = <&gpio0 22 GPIO_ACTIVE_LOW>; |
| reset-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; |
| }; |
| }; |
| |
| hs_spi1: &hs_lspi1 { |
| compatible = "nxp,lpc-spi"; |
| pinctrl-0 = <&pinmux_flexcomm16_spi>; |
| pinctrl-names = "default"; |
| dmas = <&dma0 28>, <&dma0 29>; |
| dma-names = "rx", "tx"; |
| status = "okay"; |
| }; |
| |
| arduino_serial: &flexcomm12 { |
| compatible = "nxp,lpc-usart"; |
| status = "okay"; |
| current-speed = <115200>; |
| pinctrl-0 = <&pinmux_flexcomm12_usart>; |
| pinctrl-names = "default"; |
| }; |
| |
| /* PCA9420 PMIC */ |
| &pmic_i2c { |
| status = "okay"; |
| clock-frequency = <I2C_BITRATE_FAST>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| pinctrl-0 = <&pinmux_pmic_i2c>; |
| pinctrl-names = "default"; |
| |
| pca9420: pca9420@61 { |
| reg = <0x61>; |
| compatible = "nxp,pca9420"; |
| /* |
| * This mode-reg setting will permit mode control by |
| * pins, a feature of the PCA9240. If mode control via |
| * I2C is desired, the following settings |
| * should be used: |
| * regulator-initial-mode = <PCA9420_MODECFG0_I2C>; |
| * regulator-allowed-modes = <PCA9420_MODECFG0_I2C>, |
| * <PCA9420_MODECFG1_I2C>, |
| * <PCA9420_MODECFG2_I2C>, |
| * <PCA9420_MODECFG3_I2C>; |
| * modesel-reg = <PCA9420_TOP_CNTL3>; |
| * modesel-mask = <PCA9420_TOP_CNTL3_MODE_I2C_MASK>; |
| */ |
| regulator-allowed-modes = <PCA9420_MODECFG0_PIN>, |
| <PCA9420_MODECFG1_PIN>, |
| <PCA9420_MODECFG2_PIN>, |
| <PCA9420_MODECFG3_PIN>; |
| regulator-initial-mode = <PCA9420_MODECFG0_PIN>; |
| modesel-reg = <PCA9420_MODECFG_0_0>; |
| modesel-mask = <PCA9420_MODECFG_0_MODE_CTRL_SEL_MASK>; |
| BUCK1 { |
| regulator-min-microvolt = <500000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-max-microamp = <250000>; |
| regulator-boot-on; |
| }; |
| |
| BUCK2 { |
| regulator-min-microvolt = <1500000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-max-microamp = <500000>; |
| regulator-boot-on; |
| }; |
| |
| LDO1 { |
| regulator-min-microvolt = <1700000>; |
| regulator-max-microvolt = <1900000>; |
| regulator-max-microamp = <1000>; |
| regulator-boot-on; |
| }; |
| |
| LDO2 { |
| regulator-min-microvolt = <1500000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-max-microamp = <250000>; |
| regulator-boot-on; |
| }; |
| |
| |
| }; |
| }; |
| |
| |
| &gpio0 { |
| status = "okay"; |
| }; |
| |
| &gpio1 { |
| status = "okay"; |
| }; |
| |
| &gpio2 { |
| status = "okay"; |
| }; |
| |
| &gpio3 { |
| status = "okay"; |
| }; |
| |
| &gpio4 { |
| status = "okay"; |
| }; |
| |
| &gpio5 { |
| status = "okay"; |
| }; |
| |
| &gpio6 { |
| status = "okay"; |
| }; |
| |
| &user_button_1 { |
| status = "okay"; |
| }; |
| |
| &user_button_2 { |
| status = "okay"; |
| }; |
| |
| &green_led { |
| status = "okay"; |
| }; |
| |
| &blue_led { |
| status = "okay"; |
| }; |
| |
| &red_led { |
| status = "okay"; |
| }; |
| |
| &dma0 { |
| /* |
| * The total number of dma channels available is defined by |
| * FSL_FEATURE_DMA_NUMBER_OF_CHANNELS in the SoC features file. |
| * Since memory from the heap pool is allocated based on the number |
| * of DMA channels, set this property to as many channels is needed |
| * for the platform. Adjust HEAP_MEM_POOL_SIZE in case you need more |
| * memory. |
| */ |
| dma-channels = <37>; |
| status = "okay"; |
| }; |
| |
| zephyr_udc0: &usbhs { |
| status = "okay"; |
| }; |
| |
| &ctimer0 { |
| status = "okay"; |
| }; |
| |
| &ctimer1 { |
| status = "okay"; |
| }; |
| |
| &ctimer2 { |
| status = "okay"; |
| }; |
| |
| &ctimer3 { |
| status = "okay"; |
| }; |
| |
| &ctimer4 { |
| status = "okay"; |
| }; |
| |
| &wwdt0 { |
| status = "okay"; |
| }; |
| |
| &flexspi { |
| status = "okay"; |
| mx25um51345g: mx25um51345g@0 { |
| compatible = "nxp,imx-flexspi-mx25um51345g"; |
| /* MX25UM51245G is 64MB, 512MBit flash part */ |
| size = <DT_SIZE_M(64 * 8)>; |
| reg = <0>; |
| spi-max-frequency = <200000000>; |
| status = "okay"; |
| jedec-id = [c2 81 3a]; |
| erase-block-size = <4096>; |
| /* |
| * Note- ECC will be disabled with a |
| * write block size of 1 byte. To enable ECC, ensure |
| * writes are in multiples of 16 bytes. This reduced |
| * block size is required for MCUBoot support. |
| */ |
| write-block-size = <1>; |
| |
| partitions { |
| compatible = "fixed-partitions"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| boot_partition: partition@0 { |
| label = "mcuboot"; |
| reg = <0x00000000 DT_SIZE_K(64)>; |
| }; |
| slot0_partition: partition@10000 { |
| label = "image-0"; |
| reg = <0x00010000 DT_SIZE_M(24)>; |
| }; |
| slot1_partition: partition@1810000 { |
| label = "image-1"; |
| reg = <0x01810000 DT_SIZE_M(24)>; |
| }; |
| scratch_partition: partition@3010000 { |
| label = "image-scratch"; |
| reg = <0x03010000 DT_SIZE_K(8128)>; |
| }; |
| storage_partition: partition@3f00000 { |
| label = "storage"; |
| reg = <0x03f00000 DT_SIZE_M(1)>; |
| }; |
| }; |
| }; |
| }; |