| # Kconfig - ETH_ENC28J60 Ethernet driver configuration options |
| |
| # |
| # Copyright (c) 2015 Intel Corporation |
| # |
| # Licensed under the Apache License, Version 2.0 (the "License"); |
| # you may not use this file except in compliance with the License. |
| # You may obtain a copy of the License at |
| # |
| # http://www.apache.org/licenses/LICENSE-2.0 |
| # |
| # Unless required by applicable law or agreed to in writing, software |
| # distributed under the License is distributed on an "AS IS" BASIS, |
| # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| # See the License for the specific language governing permissions and |
| # limitations under the License. |
| # |
| |
| menuconfig ETH_ENC28J60 |
| bool "ENC28J60C Ethernet Controller" |
| depends on ETHERNET |
| depends on SPI |
| default n |
| help |
| ENC28J60C Stand-Alone Ethernet Controller |
| with SPI Interface |
| |
| config ETH_ENC28J60_0 |
| bool "ENC28J60C Ethernet port 0" |
| depends on ETH_ENC28J60 |
| default n |
| help |
| Include port 0 driver |
| |
| if ETH_ENC28J60 && ETH_ENC28J60_0 |
| config ETH_ENC28J60_0_NAME |
| string "Driver's name" |
| default "ETH_0" |
| |
| config ETH_ENC28J60_0_INIT_PRIORITY |
| int |
| prompt "ENC28J60C init priority" |
| default 80 |
| help |
| Device driver initialization priority. |
| Since the device is connected to SPI bus, its driver has |
| to be initialized after the SPI one. |
| |
| config ETH_ENC28J60_0_GPIO_PORT_NAME |
| string "GPIO controller port name" |
| default "GPIO_0" |
| help |
| GPIO port name through which ENC28J60C interruption is received. |
| |
| config ETH_ENC28J60_0_GPIO_PIN |
| int "ENC28J60C INT GPIO PIN" |
| default 24 |
| help |
| GPIO pin number used to conect INT |
| |
| config ETH_ENC28J60_0_SPI_PORT_NAME |
| string "SPI master controller port name" |
| default "SPI_0" |
| help |
| Master I2C port name through which ENC28J60C chip is accessed. |
| |
| config ETH_ENC28J60_0_SLAVE |
| hex "ETH_ENC28J60 SPI slave select pin" |
| default 1 |
| help |
| ENC28J60C chip select pin. |
| |
| config ETH_ENC28J60_0_SPI_BUS_FREQ |
| int "ENC28J60C SPI bus speed in Hz" |
| default 128 |
| help |
| This is the maximum supported SPI bus frequency. |
| |
| config ETH_ENC28J60_0_MAC3 |
| hex "MAC Address Byte 3" |
| default 0 |
| help |
| MACADDR<0:23> are Microchip's OUI. |
| This is the byte 3 of the MAC address. |
| MACADDR<31:24> |
| |
| config ETH_ENC28J60_0_MAC4 |
| hex "MAC Address Byte 4" |
| default 0 |
| help |
| MACADDR<0:23> are Microchip's OUI. |
| This is the byte 4 of the MAC address. |
| MACADDR<40:32> |
| |
| config ETH_ENC28J60_0_MAC5 |
| hex "MAC Address Byte 5" |
| default 0 |
| help |
| MACADDR<0:23> are Microchip's OUI. |
| This is the byte 5 of the MAC address. |
| MACADDR<48:41> |
| |
| endif #ETH_ENC28J60 && ETH_ENC28J60_0 |
