| .. _nucleo_f767zi_board: |
| |
| ST Nucleo F767ZI |
| ################ |
| |
| Overview |
| ******** |
| |
| The STM32 Nucleo-144 F767ZI boards offer combinations of performance and |
| power that provide an affordable and flexible way for users to build |
| prototypes and try out new concepts. For compatible boards, the SMPS |
| significantly reduces power consumption in Run mode. |
| |
| The Arduino-compatible ST Zio connector expands functionality of the Nucleo |
| open development platform, with a wide choice of specialized Arduino* Uno V3 |
| shields. |
| |
| The STM32 Nucleo-144 board does not require any separate probe as it integrates |
| the ST-LINK/V2-1 debugger/programmer. |
| |
| The STM32 Nucleo-144 board comes with the STM32 comprehensive free software |
| libraries and examples available with the STM32Cube MCU Package. |
| |
| Key Features |
| |
| - STM32 microcontroller in LQFP144 package |
| - Ethernet compliant with IEEE-802.3-2002 (depending on STM32 support) |
| - USB OTG or full-speed device (depending on STM32 support) |
| - 3 user LEDs |
| - 2 user and reset push-buttons |
| - 32.768 kHz crystal oscillator |
| - Board connectors: |
| |
| - USB with Micro-AB |
| - SWD |
| - Ethernet RJ45 (depending on STM32 support) |
| - ST Zio connector including Arduino* Uno V3 |
| - ST morpho |
| |
| - Flexible power-supply options: ST-LINK USB VBUS or external sources. |
| - On-board ST-LINK/V2-1 debugger/programmer with USB re-enumeration |
| - capability: mass storage, virtual COM port and debug port. |
| - Comprehensive free software libraries and examples available with the |
| STM32Cube MCU package. |
| - Arm* Mbed Enabled* compliant (only for some Nucleo part numbers) |
| |
| .. image:: img/nucleo_f767zi.jpg |
| :width: 720px |
| :align: center |
| :height: 720px |
| :alt: Nucleo F767ZI |
| |
| More information about the board can be found at the `Nucleo F767ZI website`_. |
| |
| Hardware |
| ******** |
| |
| Nucleo F767ZI provides the following hardware components: |
| |
| - STM32F767ZI in LQFP144 package |
| - ARM 32-bit Cortex-M7 CPU with FPU |
| - Chrom-ART Accelerator |
| - ART Accelerator |
| - 216 MHz max CPU frequency |
| - VDD from 1.7 V to 3.6 V |
| - 2 MB Flash |
| - 512 KB SRAM |
| - 16-bit timers(10) |
| - 32-bit timers(2) |
| - SPI(6) |
| - I2C(4) |
| - I2S (3) |
| - USART(4) |
| - UART(4) |
| - USB OTG Full Speed and High Speed(1) |
| - USB OTG Full Speed(1) |
| - CAN(2) |
| - SAI(2) |
| - SPDIF_Rx(4) |
| - HDMI_CEC(1) |
| - Dual Mode Quad SPI(1) |
| - Camera Interface |
| - GPIO(up to 168) with external interrupt capability |
| - 12-bit ADC(3) with 24 channels / 2.4 MSPS |
| - 12-bit DAC with 2 channels(2) |
| - True Random Number Generator (RNG) |
| - 16-channel DMA |
| - LCD-TFT Controller with XGA resolution |
| |
| Supported Features |
| ================== |
| |
| The Zephyr nucleo_f767zi board configuration supports the following hardware |
| features: |
| |
| +-----------+------------+-------------------------------------+ |
| | Interface | Controller | Driver/Component | |
| +===========+============+=====================================+ |
| | NVIC | on-chip | nested vector interrupt controller | |
| +-----------+------------+-------------------------------------+ |
| | UART | on-chip | serial port | |
| +-----------+------------+-------------------------------------+ |
| | PINMUX | on-chip | pinmux | |
| +-----------+------------+-------------------------------------+ |
| | GPIO | on-chip | gpio | |
| +-----------+------------+-------------------------------------+ |
| | ETHERNET | on-chip | ethernet | |
| +-----------+------------+-------------------------------------+ |
| | USB | on-chip | usb_device | |
| +-----------+------------+-------------------------------------+ |
| | COUNTER | on-chip | rtc | |
| +-----------+------------+-------------------------------------+ |
| | I2C | on-chip | i2c | |
| +-----------+------------+-------------------------------------+ |
| | PWM | on-chip | pwm | |
| +-----------+------------+-------------------------------------+ |
| | SPI | on-chip | spi | |
| +-----------+------------+-------------------------------------+ |
| | WATCHDOG | on-chip | independent watchdog | |
| +-----------+------------+-------------------------------------+ |
| | ADC | on-chip | ADC Controller | |
| +-----------+------------+-------------------------------------+ |
| |
| Other hardware features are not yet supported on this Zephyr port. |
| |
| The default configuration can be found in the defconfig file: |
| ``boards/arm/nucleo_f767zi/nucleo_f767zi_defconfig`` |
| |
| For mode details please refer to `STM32 Nucleo-144 board User Manual`_. |
| |
| Default Zephyr Peripheral Mapping: |
| ---------------------------------- |
| |
| The Nucleo F767ZI board features a ST Zio connector (extended Arduino Uno V3) |
| and a ST morpho connector. Board is configured as follows: |
| |
| - UART_2 TX/RX/RTS/CTS : PD5/PD6/PD4/PD3 |
| - UART_3 TX/RX : PD8/PD9 (ST-Link Virtual Port Com) |
| - UART_6 TX/RX : PG14/PG9 (Arduino UART) |
| - USER_PB : PC13 |
| - LD1 : PB0 |
| - LD2 : PB7 |
| - LD3 : PB14 |
| - ETH : PA1, PA2, PA7, PB13, PC1, PC4, PC5, PG11, PG13 |
| - USB DM : PA11 |
| - USB DP : PA12 |
| - I2C : PB8, PB9 |
| - PWM : PE13 |
| - SPI : PA4, PA5, PA6, PA7 |
| |
| .. note:: |
| The Arduino Uno v3 specified SPI device conflicts with the on-board ETH |
| device on pin PA7. |
| |
| System Clock |
| ------------ |
| |
| Nucleo F767ZI System Clock could be driven by an internal or external |
| oscillator, as well as the main PLL clock. By default, the System clock is |
| driven by the PLL clock at 72MHz, driven by an 8MHz high-speed external clock. |
| |
| Serial Port |
| ----------- |
| |
| Nucleo F767ZI board has 4 UARTs and 4 USARTs. The Zephyr console output is |
| assigned to UART3. Default settings are 115200 8N1. |
| |
| |
| Programming and Debugging |
| ************************* |
| |
| Applications for the ``nucleo_f767zi`` board configuration can be built and |
| flashed in the usual way (see :ref:`build_an_application` and |
| :ref:`application_run` for more details). |
| |
| Flashing |
| ======== |
| |
| Nucleo F767ZI board includes an ST-LINK/V2-1 embedded debug tool interface. |
| |
| Flashing an application to Nucleo F767ZI |
| ---------------------------------------- |
| |
| Here is an example for the :ref:`hello_world` application. |
| |
| Run a serial host program to connect with your Nucleo board. |
| |
| .. code-block:: console |
| |
| $ minicom -b 115200 -D /dev/ttyACM0 |
| |
| Build and flash the application: |
| |
| .. zephyr-app-commands:: |
| :zephyr-app: samples/hello_world |
| :board: nucleo_f767zi |
| :goals: build flash |
| |
| You should see the following message on the console: |
| |
| .. code-block:: console |
| |
| $ Hello World! nucleo_f767zi |
| |
| Debugging |
| ========= |
| |
| You can debug an application in the usual way. Here is an example for the |
| :ref:`hello_world` application. |
| |
| .. zephyr-app-commands:: |
| :zephyr-app: samples/hello_world |
| :board: nucleo_f767zi |
| :maybe-skip-config: |
| :goals: debug |
| |
| .. _Nucleo f767zi website: |
| https://www.st.com/en/evaluation-tools/nucleo-f767zi.html |
| |
| .. _STM32 Nucleo-144 board User Manual: |
| http://www.st.com/resource/en/user_manual/dm00244518.pdf |
| |
| .. _STM32f767zi on www.st.com: |
| https://www.st.com/content/st_com/en/products/microcontrollers/stm32-32-bit-arm-cortex-mcus/stm32-high-performance-mcus/stm32f7-series/stm32f7x&/stm32f767zi.html |
| |
| .. _STM32F767 reference manual: |
| https://www.st.com/resource/en/reference_manual/DM00224583.pdf |
