| .. zephyr:board:: frdm_ke17z512 |
| |
| Overview |
| ******** |
| |
| The FRDM-KE17Z512 is a development board for NXP Kinetis KE1xZ 32-bit |
| MCU-based platforms. The onboard OpenSDAv2 serial and debug adapter, |
| running an open source bootloader, offers options for serial |
| communication, flash programming, and run-control debugging. |
| |
| Hardware |
| ******** |
| |
| - MKE17Z512VLL9 MCU (up to 96 MHz, 512 KB flash memory, 96 KB RAM, |
| and 100 Low profile Quad Flat Package (LQFP)) |
| - 3.3 V or 5 V MCU operation |
| - 6-axis FXOS8700CQ digital accelerometer and magnetometer |
| - RGB LED |
| - Two user push-buttons |
| - Thermistor |
| - Arduino compatible I/O pin header |
| - OpenSDA on-board debugger |
| - Two Touch Electrodes |
| |
| For more information about the KE1xZ SoC and the FRDM-KE17Z512 board, see |
| these NXP reference documents: |
| |
| - `KE1xZ Website`_ |
| - `KE1xZ Fact Sheet`_ |
| - `KE1xZ Reference Manual`_ |
| - `FRDM-KE17Z512 Website`_ |
| - `FRDM-KE17Z512 Quick Start Guide`_ |
| - `FRDM-KE17Z512 Reference Manual`_ |
| |
| Supported Features |
| ================== |
| |
| .. zephyr:board-supported-hw:: |
| |
| System Clock |
| ============ |
| |
| The KE17Z9 SoC is configured to run at 48 MHz using the FIRC. |
| |
| Serial Port |
| =========== |
| |
| The KE17Z9 SoC has three LPUARTs. UART2 is configured for the console. |
| |
| Programming and Debugging |
| ************************* |
| |
| .. zephyr:board-supported-runners:: |
| |
| Build and flash applications as usual (see :ref:`build_an_application` and |
| :ref:`application_run` for more details). |
| |
| Configuring a Debug Probe |
| ========================= |
| |
| A debug probe is used for both flashing and debugging the board. This board is |
| configured by default to use Linkserver. |
| |
| Early versions of this board have an outdated version of the OpenSDA bootloader |
| and require an update. Please see the `DAPLink Bootloader Update`_ page for |
| instructions to update from the CMSIS-DAP bootloader to the DAPLink bootloader. |
| |
| Option 1: Linkserver |
| -------------------- |
| |
| Install the :ref:`linkserver-debug-host-tools` and make sure they are in your |
| search path. LinkServer works with the default CMSIS-DAP firmware included in |
| the on-board debugger. |
| |
| Linkserver is the default for this board, ``west flash`` and ``west debug`` will |
| call the linkserver runner. |
| |
| Option 2: :ref:`opensda-jlink-onboard-debug-probe` |
| -------------------------------------------------- |
| |
| Install the :ref:`jlink-debug-host-tools` and make sure they are in your search |
| path. |
| |
| Follow the instructions in :ref:`opensda-jlink-onboard-debug-probe` to program |
| the `Segger J-Link OpenSDA V2.1 Firmware`_. |
| Use the ``-r jlink`` option with west to use the jlink runner. |
| |
| .. code-block:: console |
| |
| west flash -r jlink |
| |
| Configuring a Console |
| ===================== |
| |
| Regardless of your choice in debug probe, we will use the OpenSDA |
| microcontroller as a usb-to-serial adapter for the serial console. |
| |
| Connect a USB cable from your PC to J10. |
| |
| Use the following settings with your serial terminal of choice (minicom, putty, |
| etc.): |
| |
| - Speed: 115200 |
| - Data: 8 bits |
| - Parity: None |
| - Stop bits: 1 |
| |
| Flashing |
| ======== |
| |
| Here is an example for the :zephyr:code-sample:`hello_world` application. |
| |
| .. zephyr-app-commands:: |
| :zephyr-app: samples/hello_world |
| :board: frdm_ke17z512 |
| :goals: flash |
| |
| Open a serial terminal, reset the board (press the SW1 button), and you should |
| see the following message in the terminal: |
| |
| .. code-block:: console |
| |
| *** Booting Zephyr OS build v3.6.0-xxxx-gxxxxxxxxxxxx *** |
| Hello World! frdm_ke17z512/mke17z9 |
| |
| Debugging |
| ========= |
| |
| Here is an example for the :zephyr:code-sample:`hello_world` application. |
| |
| .. zephyr-app-commands:: |
| :zephyr-app: samples/hello_world |
| :board: frdm_ke17z512 |
| :goals: debug |
| |
| Open a serial terminal, step through the application in your debugger, and you |
| should see the following message in the terminal: |
| |
| .. code-block:: console |
| |
| *** Booting Zephyr OS build v3.6.0-xxxx-gxxxxxxxxxxxx *** |
| Hello World! frdm_ke17z512/mke17z9 |
| |
| .. include:: ../../common/board-footer.rst |
| :start-after: nxp-board-footer |
| |
| .. _FRDM-KE17Z512 Website: |
| https://www.nxp.com/design/design-center/development-boards-and-designs/general-purpose-mcus/frdm-development-board-for-96-mhz-ke17z-ke13z-ke12z-with-512-kb-flash-mcus:FRDM-KE17Z512 |
| |
| .. _FRDM-KE17Z512 Quick Start Guide: |
| https://www.nxp.com/docs/en/quick-reference-guide/FRDMKE17Z512QSG.pdf |
| |
| .. _FRDM-KE17Z512 Reference Manual: |
| https://www.nxp.com/docs/en/reference-manual/KE1XZP100M96SF0RM.pdf |
| |
| .. _KE1xZ Website: |
| https://www.nxp.com/products/processors-and-microcontrollers/arm-microcontrollers/general-purpose-mcus/ke-series-arm-cortex-m4-m0-plus/ke1xz-arm-cortex-m0-plus-5v-main-stream-mcu-with-nxp-touch-and-can-control:KE1xZ |
| |
| .. _KE1xZ Fact Sheet: |
| https://www.nxp.com/docs/en/fact-sheet/KE1xZMCUFAMFS.pdf |
| |
| .. _KE1xZ Reference Manual: |
| https://www.nxp.com/webapp/Download?colCode=KE1XZP100M72SF0RM |
| |
| .. _linkserver-debug-host-tools: |
| https://www.nxp.com/lgfiles/updates/mcuxpresso/LinkServer_1.5.30.exe |
| |
| .. _Segger J-Link OpenSDA V2.1 Firmware: |
| https://www.segger.com/downloads/jlink/OpenSDA_V2_1.bin |
| |
| .. _DAPLink Bootloader Update: |
| https://os.mbed.com/blog/entry/DAPLink-bootloader-update/ |
| |
| .. _jlink-debug-host-tools: |
| https://www.segger.com/downloads/jlink/JLink_Windows_V794_x86_64.exe |
