| /** |
| * Copyright (c) 2015 - 2018, Nordic Semiconductor ASA |
| * All rights reserved. |
| * |
| * Redistribution and use in source and binary forms, with or without |
| * modification, are permitted provided that the following conditions are met: |
| * |
| * 1. Redistributions of source code must retain the above copyright notice, this |
| * list of conditions and the following disclaimer. |
| * |
| * 2. Redistributions in binary form must reproduce the above copyright |
| * notice, this list of conditions and the following disclaimer in the |
| * documentation and/or other materials provided with the distribution. |
| * |
| * 3. Neither the name of the copyright holder nor the names of its |
| * contributors may be used to endorse or promote products derived from this |
| * software without specific prior written permission. |
| * |
| * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" |
| * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE |
| * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE |
| * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE |
| * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR |
| * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF |
| * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS |
| * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN |
| * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) |
| * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE |
| * POSSIBILITY OF SUCH DAMAGE. |
| */ |
| |
| #ifndef NRFX_I2S_H__ |
| #define NRFX_I2S_H__ |
| |
| #include <nrfx.h> |
| #include <hal/nrf_i2s.h> |
| |
| #ifdef __cplusplus |
| extern "C" { |
| #endif |
| |
| /** |
| * @defgroup nrfx_i2s I2S driver |
| * @{ |
| * @ingroup nrf_i2s |
| * @brief Inter-IC Sound (I2S) peripheral driver. |
| */ |
| |
| |
| /** |
| * @brief This value can be provided instead of a pin number for the signals |
| * SDOUT, SDIN, and MCK to specify that a given signal is not used |
| * and therefore does not need to be connected to a pin. |
| */ |
| #define NRFX_I2S_PIN_NOT_USED 0xFF |
| |
| /** @brief I2S driver configuration structure. */ |
| typedef struct |
| { |
| uint8_t sck_pin; ///< SCK pin number. |
| uint8_t lrck_pin; ///< LRCK pin number. |
| uint8_t mck_pin; ///< MCK pin number. |
| /**< Optional. Use @ref NRFX_I2S_PIN_NOT_USED |
| * if this signal is not needed. */ |
| uint8_t sdout_pin; ///< SDOUT pin number. |
| /**< Optional. Use @ref NRFX_I2S_PIN_NOT_USED |
| * if this signal is not needed. */ |
| uint8_t sdin_pin; ///< SDIN pin number. |
| /**< Optional. Use @ref NRFX_I2S_PIN_NOT_USED |
| * if this signal is not needed. */ |
| uint8_t irq_priority; ///< Interrupt priority. |
| |
| nrf_i2s_mode_t mode; ///< Mode of operation. |
| nrf_i2s_format_t format; ///< Frame format. |
| nrf_i2s_align_t alignment; ///< Alignment of sample within a frame. |
| nrf_i2s_swidth_t sample_width; ///< Sample width. |
| nrf_i2s_channels_t channels; ///< Enabled channels. |
| nrf_i2s_mck_t mck_setup; ///< Master clock setup. |
| nrf_i2s_ratio_t ratio; ///< MCK/LRCK ratio. |
| } nrfx_i2s_config_t; |
| |
| /** @brief I2S driver buffers structure. */ |
| typedef struct |
| { |
| uint32_t * p_rx_buffer; |
| uint32_t const * p_tx_buffer; |
| } nrfx_i2s_buffers_t; |
| |
| /** |
| * @brief I2S driver default configuration. |
| */ |
| #define NRFX_I2S_DEFAULT_CONFIG \ |
| { \ |
| .sck_pin = NRFX_I2S_CONFIG_SCK_PIN, \ |
| .lrck_pin = NRFX_I2S_CONFIG_LRCK_PIN, \ |
| .mck_pin = NRFX_I2S_CONFIG_MCK_PIN, \ |
| .sdout_pin = NRFX_I2S_CONFIG_SDOUT_PIN, \ |
| .sdin_pin = NRFX_I2S_CONFIG_SDIN_PIN, \ |
| .irq_priority = NRFX_I2S_CONFIG_IRQ_PRIORITY, \ |
| .mode = (nrf_i2s_mode_t)NRFX_I2S_CONFIG_MASTER, \ |
| .format = (nrf_i2s_format_t)NRFX_I2S_CONFIG_FORMAT, \ |
| .alignment = (nrf_i2s_align_t)NRFX_I2S_CONFIG_ALIGN, \ |
| .sample_width = (nrf_i2s_swidth_t)NRFX_I2S_CONFIG_SWIDTH, \ |
| .channels = (nrf_i2s_channels_t)NRFX_I2S_CONFIG_CHANNELS, \ |
| .mck_setup = (nrf_i2s_mck_t)NRFX_I2S_CONFIG_MCK_SETUP, \ |
| .ratio = (nrf_i2s_ratio_t)NRFX_I2S_CONFIG_RATIO, \ |
| } |
| |
| |
| #define NRFX_I2S_STATUS_NEXT_BUFFERS_NEEDED (1UL << 0) |
| /**< The application should provide buffers that are to be used in the next |
| * part of the transfer. A call to @ref nrfx_i2s_next_buffers_set should |
| * be done before the currently used buffers are completely processed |
| * (i.e. the time remaining for supplying the next buffers depends on |
| * the used size of the buffers). */ |
| |
| /** |
| * @brief I2S driver data handler type. |
| * |
| * A data handling function of this type must be specified during initialization |
| * of the driver. The driver will call this function when it finishes using |
| * buffers passed to it by the application, and when it needs to be provided |
| * with buffers for the next part of the transfer. |
| * |
| * @note The @c p_released pointer passed to this function is temporary and |
| * will be invalid after the function returns, hence it cannot be stored |
| * and used later. If needed, the pointed content (i.e. buffers pointers) |
| * should be copied instead. |
| * |
| * @param[in] p_released Pointer to a structure with pointers to buffers |
| * passed previously to the driver that will no longer |
| * be access by it (they can be now safely released or |
| * used for another purpose, in particular for a next |
| * part of the transfer). |
| * This pointer will be NULL if the application did not |
| * supply the buffers for the next part of the transfer |
| * (via a call to @ref nrfx_i2s_next_buffers_set) since |
| * the previous time the data handler signaled such need. |
| * This means that data corruption occurred (the previous |
| * buffers are used for the second time) and no buffers |
| * can be released at the moment. |
| * Both pointers in this structure are NULL when the |
| * handler is called for the first time after a transfer |
| * is started, because no data has been transferred yet |
| * at this point. In all successive calls the pointers |
| * specify what has been sent (TX) and what has been |
| * received (RX) in the part of transfer that has just |
| * been completed (provided that a given direction is |
| * enabled, see @ref nrfx_i2s_start). |
| * @param[in] status Bit field describing the current status of the transfer. |
| * It can be 0 or a combination of the following flags: |
| * - @ref NRFX_I2S_STATUS_NEXT_BUFFERS_NEEDED |
| */ |
| typedef void (* nrfx_i2s_data_handler_t)(nrfx_i2s_buffers_t const * p_released, |
| uint32_t status); |
| |
| |
| /** |
| * @brief Function for initializing the I2S driver. |
| * |
| * @param[in] p_config Pointer to the structure with initial configuration. |
| * @param[in] handler Data handler provided by the user. Must not be NULL. |
| * |
| * @retval NRFX_SUCCESS If initialization was successful. |
| * @retval NRFX_ERROR_INVALID_STATE If the driver was already initialized. |
| * @retval NRFX_ERROR_INVALID_PARAM If the requested combination of configuration |
| * options is not allowed by the I2S peripheral. |
| */ |
| nrfx_err_t nrfx_i2s_init(nrfx_i2s_config_t const * p_config, |
| nrfx_i2s_data_handler_t handler); |
| |
| /** @brief Function for uninitializing the I2S driver. */ |
| void nrfx_i2s_uninit(void); |
| |
| /** |
| * @brief Function for starting the continuous I2S transfer. |
| * |
| * The I2S data transfer can be performed in one of three modes: RX (reception) |
| * only, TX (transmission) only, or in both directions simultaneously. |
| * The mode is selected by specifying a proper buffer for a given direction |
| * in the call to this function or by passing NULL instead if this direction |
| * should be disabled. |
| * |
| * The length of the buffer (which is a common value for RX and TX if both |
| * directions are enabled) is specified in 32-bit words. One 32-bit memory |
| * word can either contain four 8-bit samples, two 16-bit samples, or one |
| * right-aligned 24-bit sample sign-extended to a 32-bit value. |
| * For a detailed memory mapping for different supported configurations, |
| * see the @linkProductSpecification52. |
| * |
| * @note Peripherals using EasyDMA (including I2S) require the transfer buffers |
| * to be placed in the Data RAM region. If this condition is not met, |
| * this function will fail with the error code NRFX_ERROR_INVALID_ADDR. |
| * |
| * @param[in] p_initial_buffers Pointer to a structure specifying the buffers |
| * to be used in the initial part of the transfer |
| * (buffers for all consecutive parts are provided |
| * through the data handler). |
| * @param[in] buffer_size Size of the buffers (in 32-bit words). |
| * Must not be 0. |
| * @param[in] flags Transfer options (0 for default settings). |
| * Currently, no additional flags are available. |
| * |
| * @retval NRFX_SUCCESS If the operation was successful. |
| * @retval NRFX_ERROR_INVALID_STATE If a transfer was already started or |
| * the driver has not been initialized. |
| * @retval NRFX_ERROR_INVALID_ADDR If the provided buffers are not placed |
| * in the Data RAM region. |
| */ |
| nrfx_err_t nrfx_i2s_start(nrfx_i2s_buffers_t const * p_initial_buffers, |
| uint16_t buffer_size, |
| uint8_t flags); |
| |
| /** |
| * @brief Function for supplying the buffers to be used in the next part of |
| * the transfer. |
| * |
| * The application should call this function when the data handler receives |
| * @ref NRFX_I2S_STATUS_NEXT_BUFFERS_NEEDED in the @c status parameter. |
| * The call can be done immediately from the data handler function or later, |
| * but it has to be done before the I2S peripheral finishes processing the |
| * buffers supplied previously. Otherwise, data corruption will occur. |
| * |
| * @sa nrfx_i2s_data_handler_t |
| * |
| * @retval NRFX_SUCCESS If the operation was successful. |
| * @retval NRFX_ERROR_INVALID_STATE If the buffers were already supplied or |
| * the peripheral is currently being stopped. |
| */ |
| nrfx_err_t nrfx_i2s_next_buffers_set(nrfx_i2s_buffers_t const * p_buffers); |
| |
| /** @brief Function for stopping the I2S transfer. */ |
| void nrfx_i2s_stop(void); |
| |
| /** @} */ |
| |
| |
| void nrfx_i2s_irq_handler(void); |
| |
| |
| #ifdef __cplusplus |
| } |
| #endif |
| |
| #endif // NRFX_I2S_H__ |