blob: 34fb07d646a2b5078698ed7a30ae1f15ce705d5c [file] [log] [blame]
/* gpio_sch.c - Driver implementation for Intel SCH GPIO controller */
/*
* Copyright (c) 2015 Intel Corporation.
*
* SPDX-License-Identifier: Apache-2.0
*/
#include <errno.h>
#include <kernel.h>
#include <board.h>
#include <init.h>
#include <sys_io.h>
#include <misc/util.h>
#include "gpio_sch.h"
#include "gpio_utils.h"
#define SYS_LOG_LEVEL CONFIG_SYS_LOG_GPIO_LEVEL
#include <logging/sys_log.h>
/* Define GPIO_SCH_LEGACY_IO_PORTS_ACCESS
* inside soc.h if the GPIO controller
* requires I/O port access instead of
* memory mapped I/O.
*/
#ifdef GPIO_SCH_LEGACY_IO_PORTS_ACCESS
#define _REG_READ sys_in32
#define _REG_WRITE sys_out32
#define _REG_SET_BIT sys_io_set_bit
#define _REG_CLEAR_BIT sys_io_clear_bit
#else
#define _REG_READ sys_read32
#define _REG_WRITE sys_write32
#define _REG_SET_BIT sys_set_bit
#define _REG_CLEAR_BIT sys_clear_bit
#endif /* GPIO_SCH_LEGACY_IO_PORTS_ACCESS */
#define DEFINE_MM_REG_READ(__reg, __off) \
static inline uint32_t _read_##__reg(uint32_t addr) \
{ \
return _REG_READ(addr + __off); \
}
#define DEFINE_MM_REG_WRITE(__reg, __off) \
static inline void _write_##__reg(uint32_t data, uint32_t addr) \
{ \
_REG_WRITE(data, addr + __off); \
}
DEFINE_MM_REG_READ(glvl, GPIO_SCH_REG_GLVL)
DEFINE_MM_REG_WRITE(glvl, GPIO_SCH_REG_GLVL)
DEFINE_MM_REG_WRITE(gtpe, GPIO_SCH_REG_GTPE)
DEFINE_MM_REG_WRITE(gtne, GPIO_SCH_REG_GTNE)
DEFINE_MM_REG_READ(gts, GPIO_SCH_REG_GTS)
DEFINE_MM_REG_WRITE(gts, GPIO_SCH_REG_GTS)
static void _set_bit(uint32_t base_addr,
uint32_t bit, uint8_t set)
{
if (!set) {
_REG_CLEAR_BIT(base_addr, bit);
} else {
_REG_SET_BIT(base_addr, bit);
}
}
#define DEFINE_MM_REG_SET_BIT(__reg, __off) \
static inline void _set_bit_##__reg(uint32_t addr, \
uint32_t bit, uint8_t set) \
{ \
_set_bit(addr + __off, bit, set); \
}
DEFINE_MM_REG_SET_BIT(gen, GPIO_SCH_REG_GEN)
DEFINE_MM_REG_SET_BIT(gio, GPIO_SCH_REG_GIO)
DEFINE_MM_REG_SET_BIT(glvl, GPIO_SCH_REG_GLVL)
DEFINE_MM_REG_SET_BIT(gtpe, GPIO_SCH_REG_GTPE)
DEFINE_MM_REG_SET_BIT(gtne, GPIO_SCH_REG_GTNE)
static inline void _set_data_reg(uint32_t *reg, uint8_t pin, uint8_t set)
{
*reg &= ~(BIT(pin));
*reg |= (set << pin) & BIT(pin);
}
static void _gpio_pin_config(struct device *dev, uint32_t pin, int flags)
{
const struct gpio_sch_config *info = dev->config->config_info;
struct gpio_sch_data *gpio = dev->driver_data;
uint8_t active_high = 0;
uint8_t active_low = 0;
_set_bit_gen(info->regs, pin, 1);
_set_bit_gio(info->regs, pin, !(flags & GPIO_DIR_MASK));
if (flags & GPIO_INT) {
if (flags & GPIO_INT_ACTIVE_HIGH) {
active_high = 1;
} else {
active_low = 1;
}
SYS_LOG_DBG("Setting up pin %d to active_high %d and "
"active_low %d", active_high, active_low);
}
/* We store the gtpe/gtne settings. These will be used once
* we enable the callback for the pin, or the whole port
*/
_set_data_reg(&gpio->int_regs.gtpe, pin, active_high);
_set_data_reg(&gpio->int_regs.gtne, pin, active_low);
}
static inline void _gpio_port_config(struct device *dev, int flags)
{
const struct gpio_sch_config *info = dev->config->config_info;
int pin;
for (pin = 0; pin < info->bits; pin++) {
_gpio_pin_config(dev, pin, flags);
}
}
static int gpio_sch_config(struct device *dev,
int access_op, uint32_t pin, int flags)
{
const struct gpio_sch_config *info = dev->config->config_info;
if (access_op == GPIO_ACCESS_BY_PIN) {
if (pin >= info->bits) {
return -EINVAL;
}
_gpio_pin_config(dev, pin, flags);
} else {
_gpio_port_config(dev, flags);
}
return 0;
}
static int gpio_sch_write(struct device *dev,
int access_op, uint32_t pin, uint32_t value)
{
const struct gpio_sch_config *info = dev->config->config_info;
if (access_op == GPIO_ACCESS_BY_PIN) {
if (pin >= info->bits) {
return -ENOTSUP;
}
_set_bit_glvl(info->regs, pin, value);
} else {
_write_glvl(info->regs, value);
}
return 0;
}
static int gpio_sch_read(struct device *dev,
int access_op, uint32_t pin, uint32_t *value)
{
const struct gpio_sch_config *info = dev->config->config_info;
*value = _read_glvl(info->regs);
if (access_op == GPIO_ACCESS_BY_PIN) {
if (pin >= info->bits) {
return -ENOTSUP;
}
*value = !!(*value & BIT(pin));
}
return 0;
}
static void _gpio_sch_poll_status(void *arg1, void *unused1, void *unused2)
{
struct device *dev = (struct device *)arg1;
const struct gpio_sch_config *info = dev->config->config_info;
struct gpio_sch_data *gpio = dev->driver_data;
ARG_UNUSED(unused1);
ARG_UNUSED(unused2);
/* Cleaning up GTS first */
_write_gts(_read_gts(info->regs), info->regs);
while (gpio->poll) {
uint32_t status;
status = _read_gts(info->regs);
if (!status) {
goto loop;
}
_gpio_fire_callbacks(&gpio->callbacks, dev, status);
/* It's not documented but writing the same status value
* into GTS tells to the controller it got handled.
*/
_write_gts(status, info->regs);
loop:
k_timer_start(&gpio->poll_timer, GPIO_SCH_POLLING_MSEC, 0);
k_timer_status_sync(&gpio->poll_timer);
}
}
static void _gpio_sch_manage_callback(struct device *dev)
{
struct gpio_sch_data *gpio = dev->driver_data;
/* Start the fiber only when relevant */
if (!sys_slist_is_empty(&gpio->callbacks) && gpio->cb_enabled) {
if (!gpio->poll) {
SYS_LOG_DBG("Starting SCH GPIO polling fiber");
gpio->poll = 1;
k_thread_spawn(gpio->polling_stack,
GPIO_SCH_POLLING_STACK_SIZE,
(k_thread_entry_t)_gpio_sch_poll_status,
dev, NULL, NULL,
K_PRIO_COOP(1), 0, 0);
}
} else {
gpio->poll = 0;
}
}
static int gpio_sch_manage_callback(struct device *dev,
struct gpio_callback *callback, bool set)
{
struct gpio_sch_data *gpio = dev->driver_data;
_gpio_manage_callback(&gpio->callbacks, callback, set);
_gpio_sch_manage_callback(dev);
return 0;
}
static int gpio_sch_enable_callback(struct device *dev,
int access_op, uint32_t pin)
{
const struct gpio_sch_config *info = dev->config->config_info;
struct gpio_sch_data *gpio = dev->driver_data;
if (access_op == GPIO_ACCESS_BY_PIN) {
uint32_t bits = BIT(pin);
if (pin >= info->bits) {
return -ENOTSUP;
}
_set_bit_gtpe(info->regs, pin, !!(bits & gpio->int_regs.gtpe));
_set_bit_gtne(info->regs, pin, !!(bits & gpio->int_regs.gtne));
gpio->cb_enabled |= bits;
} else {
_write_gtpe(gpio->int_regs.gtpe, info->regs);
_write_gtne(gpio->int_regs.gtne, info->regs);
gpio->cb_enabled = BIT_MASK(info->bits);
}
_gpio_sch_manage_callback(dev);
return 0;
}
static int gpio_sch_disable_callback(struct device *dev,
int access_op, uint32_t pin)
{
const struct gpio_sch_config *info = dev->config->config_info;
struct gpio_sch_data *gpio = dev->driver_data;
if (access_op == GPIO_ACCESS_BY_PIN) {
if (pin >= info->bits) {
return -ENOTSUP;
}
_set_bit_gtpe(info->regs, pin, 0);
_set_bit_gtne(info->regs, pin, 0);
gpio->cb_enabled &= ~BIT(pin);
} else {
_write_gtpe(0, info->regs);
_write_gtne(0, info->regs);
gpio->cb_enabled = 0;
}
_gpio_sch_manage_callback(dev);
return 0;
}
static const struct gpio_driver_api gpio_sch_api = {
.config = gpio_sch_config,
.write = gpio_sch_write,
.read = gpio_sch_read,
.manage_callback = gpio_sch_manage_callback,
.enable_callback = gpio_sch_enable_callback,
.disable_callback = gpio_sch_disable_callback,
};
static int gpio_sch_init(struct device *dev)
{
struct gpio_sch_data *gpio = dev->driver_data;
dev->driver_api = &gpio_sch_api;
k_timer_init(&gpio->poll_timer, NULL, NULL);
SYS_LOG_DBG("SCH GPIO Intel Driver initialized on device: %p", dev);
return 0;
}
#if CONFIG_GPIO_SCH_0
static const struct gpio_sch_config gpio_sch_0_config = {
.regs = GPIO_SCH_0_BASE_ADDR,
.bits = GPIO_SCH_0_BITS,
};
static struct gpio_sch_data gpio_data_0;
DEVICE_INIT(gpio_0, CONFIG_GPIO_SCH_0_DEV_NAME, gpio_sch_init,
&gpio_data_0, &gpio_sch_0_config,
POST_KERNEL, CONFIG_GPIO_SCH_INIT_PRIORITY);
#endif /* CONFIG_GPIO_SCH_0 */
#if CONFIG_GPIO_SCH_1
static const struct gpio_sch_config gpio_sch_1_config = {
.regs = GPIO_SCH_1_BASE_ADDR,
.bits = GPIO_SCH_1_BITS,
};
static struct gpio_sch_data gpio_data_1;
DEVICE_INIT(gpio_1, CONFIG_GPIO_SCH_1_DEV_NAME, gpio_sch_init,
&gpio_data_1, &gpio_sch_1_config,
POST_KERNEL, CONFIG_GPIO_SCH_INIT_PRIORITY);
#endif /* CONFIG_GPIO_SCH_1 */