/** | |
****************************************************************************** | |
* @file stm32f7xx_hal_i2c.c | |
* @author MCD Application Team | |
* @version V1.1.1 | |
* @date 01-July-2016 | |
* @brief I2C HAL module driver. | |
* This file provides firmware functions to manage the following | |
* functionalities of the Inter Integrated Circuit (I2C) peripheral: | |
* + Initialization and de-initialization functions | |
* + IO operation functions | |
* + Peripheral State and Errors functions | |
* | |
@verbatim | |
============================================================================== | |
##### How to use this driver ##### | |
============================================================================== | |
[..] | |
The I2C HAL driver can be used as follows: | |
(#) Declare a I2C_HandleTypeDef handle structure, for example: | |
I2C_HandleTypeDef hi2c; | |
(#)Initialize the I2C low level resources by implementing the HAL_I2C_MspInit() API: | |
(##) Enable the I2Cx interface clock | |
(##) I2C pins configuration | |
(+++) Enable the clock for the I2C GPIOs | |
(+++) Configure I2C pins as alternate function open-drain | |
(##) NVIC configuration if you need to use interrupt process | |
(+++) Configure the I2Cx interrupt priority | |
(+++) Enable the NVIC I2C IRQ Channel | |
(##) DMA Configuration if you need to use DMA process | |
(+++) Declare a DMA_HandleTypeDef handle structure for the transmit or receive stream | |
(+++) Enable the DMAx interface clock using | |
(+++) Configure the DMA handle parameters | |
(+++) Configure the DMA Tx or Rx stream | |
(+++) Associate the initialized DMA handle to the hi2c DMA Tx or Rx handle | |
(+++) Configure the priority and enable the NVIC for the transfer complete interrupt on | |
the DMA Tx or Rx stream | |
(#) Configure the Communication Clock Timing, Own Address1, Master Addressing mode, Dual Addressing mode, | |
Own Address2, Own Address2 Mask, General call and Nostretch mode in the hi2c Init structure. | |
(#) Initialize the I2C registers by calling the HAL_I2C_Init(), configures also the low level Hardware | |
(GPIO, CLOCK, NVIC...etc) by calling the customized HAL_I2C_MspInit(&hi2c) API. | |
(#) To check if target device is ready for communication, use the function HAL_I2C_IsDeviceReady() | |
(#) For I2C IO and IO MEM operations, three operation modes are available within this driver : | |
*** Polling mode IO operation *** | |
================================= | |
[..] | |
(+) Transmit in master mode an amount of data in blocking mode using HAL_I2C_Master_Transmit() | |
(+) Receive in master mode an amount of data in blocking mode using HAL_I2C_Master_Receive() | |
(+) Transmit in slave mode an amount of data in blocking mode using HAL_I2C_Slave_Transmit() | |
(+) Receive in slave mode an amount of data in blocking mode using HAL_I2C_Slave_Receive() | |
*** Polling mode IO MEM operation *** | |
===================================== | |
[..] | |
(+) Write an amount of data in blocking mode to a specific memory address using HAL_I2C_Mem_Write() | |
(+) Read an amount of data in blocking mode from a specific memory address using HAL_I2C_Mem_Read() | |
*** Interrupt mode IO operation *** | |
=================================== | |
[..] | |
(+) Transmit in master mode an amount of data in non-blocking mode using HAL_I2C_Master_Transmit_IT() | |
(+) At transmission end of transfer, HAL_I2C_MasterTxCpltCallback() is executed and user can | |
add his own code by customization of function pointer HAL_I2C_MasterTxCpltCallback() | |
(+) Receive in master mode an amount of data in non-blocking mode using HAL_I2C_Master_Receive_IT() | |
(+) At reception end of transfer, HAL_I2C_MasterRxCpltCallback() is executed and user can | |
add his own code by customization of function pointer HAL_I2C_MasterRxCpltCallback() | |
(+) Transmit in slave mode an amount of data in non-blocking mode using HAL_I2C_Slave_Transmit_IT() | |
(+) At transmission end of transfer, HAL_I2C_SlaveTxCpltCallback() is executed and user can | |
add his own code by customization of function pointer HAL_I2C_SlaveTxCpltCallback() | |
(+) Receive in slave mode an amount of data in non-blocking mode using HAL_I2C_Slave_Receive_IT() | |
(+) At reception end of transfer, HAL_I2C_SlaveRxCpltCallback() is executed and user can | |
add his own code by customization of function pointer HAL_I2C_SlaveRxCpltCallback() | |
(+) In case of transfer Error, HAL_I2C_ErrorCallback() function is executed and user can | |
add his own code by customization of function pointer HAL_I2C_ErrorCallback() | |
(+) Abort a master I2C process communication with Interrupt using HAL_I2C_Master_Abort_IT() | |
(+) End of abort process, HAL_I2C_MasterRxCpltCallback() or HAL_I2C_MasterTxCpltCallback() is executed and user can | |
add his own code by customization of function pointer HAL_I2C_MasterRxCpltCallback() or HAL_I2C_MasterTxCpltCallback() | |
(+) Discard a slave I2C process communication using __HAL_I2C_GENERATE_NACK() macro. | |
This action will inform Master to generate a Stop condition to discard the communication. | |
*** Interrupt mode IO sequential operation *** | |
=================================== | |
[..] | |
(@) These interfaces allow to manage a sequential transfer with a repeated start condition | |
when a direction change during transfer | |
[..] | |
(+) A specific option field manage the different steps of a sequential transfer | |
(+) Option field values are defined through I2C_XFEROPTIONS and are listed below: | |
(++) I2C_FIRST_AND_LAST_FRAME: No sequential usage, functionnal is same as associated interfaces in no sequential mode | |
(++) I2C_FIRST_FRAME: Sequential usage, this option allow to manage a sequence with start condition, address | |
and data to transfer without a final stop condition | |
(++) I2C_NEXT_FRAME: Sequential usage, this option allow to manage a sequence with a restart condition, address | |
and with new data to transfer if the direction change or manage only the new data to transfer | |
if no direction change and without a final stop condition in both cases | |
(++) I2C_LAST_FRAME: Sequential usage, this option allow to manage a sequance with a restart condition, address | |
and with new data to transfer if the direction change or manage only the new data to transfer | |
if no direction change and with a final stop condition in both cases | |
(+) Differents sequential I2C interfaces are listed below: | |
(++) Sequential transmit in master I2C mode an amount of data in non-blocking mode using HAL_I2C_Master_Sequential_Transmit_IT() | |
(+++) At transmission end of current frame transfer, HAL_I2C_MasterTxCpltCallback() is executed and user can | |
add his own code by customization of function pointer HAL_I2C_MasterTxCpltCallback() | |
(++) Sequential receive in master I2C mode an amount of data in non-blocking mode using HAL_I2C_Master_Sequential_Receive_IT() | |
(+++) At reception end of current frame transfer, HAL_I2C_MasterRxCpltCallback() is executed and user can | |
add his own code by customization of function pointer HAL_I2C_MasterRxCpltCallback() | |
(++) Abort a master I2C process communication with Interrupt using HAL_I2C_Master_Abort_IT() | |
(+++) End of abort process, HAL_I2C_AbortCpltCallback() is executed and user can | |
add his own code by customization of function pointer HAL_I2C_AbortCpltCallback() | |
(+++) mean HAL_I2C_MasterTxCpltCallback() in case of previous state was master transmit | |
(+++) mean HAL_I2c_MasterRxCpltCallback() in case of previous state was master receive | |
(++) Enable/disable the Address listen mode in slave I2C mode using HAL_I2C_EnableListen_IT() HAL_I2C_DisableListen_IT() | |
(+++) When address slave I2C match, HAL_I2C_AddrCallback() is executed and user can | |
add his own code to check the Address Match Code and the transmission direction request by master (Write/Read). | |
(+++) At Listen mode end HAL_I2C_ListenCpltCallback() is executed and user can | |
add his own code by customization of function pointer HAL_I2C_ListenCpltCallback() | |
(++) Sequential transmit in slave I2C mode an amount of data in non-blocking mode using HAL_I2C_Slave_Sequential_Transmit_IT() | |
(+++) At transmission end of current frame transfer, HAL_I2C_SlaveTxCpltCallback() is executed and user can | |
add his own code by customization of function pointer HAL_I2C_SlaveTxCpltCallback() | |
(++) Sequential receive in slave I2C mode an amount of data in non-blocking mode using HAL_I2C_Slave_Sequential_Receive_IT() | |
(+++) At reception end of current frame transfer, HAL_I2C_SlaveRxCpltCallback() is executed and user can | |
add his own code by customization of function pointer HAL_I2C_SlaveRxCpltCallback() | |
(++) In case of transfer Error, HAL_I2C_ErrorCallback() function is executed and user can | |
add his own code by customization of function pointer HAL_I2C_ErrorCallback() | |
(++) Abort a master I2C process communication with Interrupt using HAL_I2C_Master_Abort_IT() | |
(++) End of abort process, HAL_I2C_AbortCpltCallback() is executed and user can | |
add his own code by customization of function pointer HAL_I2C_AbortCpltCallback() | |
(++) Discard a slave I2C process communication using __HAL_I2C_GENERATE_NACK() macro. | |
This action will inform Master to generate a Stop condition to discard the communication. | |
*** Interrupt mode IO MEM operation *** | |
======================================= | |
[..] | |
(+) Write an amount of data in non-blocking mode with Interrupt to a specific memory address using | |
HAL_I2C_Mem_Write_IT() | |
(+) At Memory end of write transfer, HAL_I2C_MemTxCpltCallback() is executed and user can | |
add his own code by customization of function pointer HAL_I2C_MemTxCpltCallback() | |
(+) Read an amount of data in non-blocking mode with Interrupt from a specific memory address using | |
HAL_I2C_Mem_Read_IT() | |
(+) At Memory end of read transfer, HAL_I2C_MemRxCpltCallback() is executed and user can | |
add his own code by customization of function pointer HAL_I2C_MemRxCpltCallback() | |
(+) In case of transfer Error, HAL_I2C_ErrorCallback() function is executed and user can | |
add his own code by customization of function pointer HAL_I2C_ErrorCallback() | |
*** DMA mode IO operation *** | |
============================== | |
[..] | |
(+) Transmit in master mode an amount of data in non-blocking mode (DMA) using | |
HAL_I2C_Master_Transmit_DMA() | |
(+) At transmission end of transfer, HAL_I2C_MasterTxCpltCallback() is executed and user can | |
add his own code by customization of function pointer HAL_I2C_MasterTxCpltCallback() | |
(+) Receive in master mode an amount of data in non-blocking mode (DMA) using | |
HAL_I2C_Master_Receive_DMA() | |
(+) At reception end of transfer, HAL_I2C_MasterRxCpltCallback() is executed and user can | |
add his own code by customization of function pointer HAL_I2C_MasterRxCpltCallback() | |
(+) Transmit in slave mode an amount of data in non-blocking mode (DMA) using | |
HAL_I2C_Slave_Transmit_DMA() | |
(+) At transmission end of transfer, HAL_I2C_SlaveTxCpltCallback() is executed and user can | |
add his own code by customization of function pointer HAL_I2C_SlaveTxCpltCallback() | |
(+) Receive in slave mode an amount of data in non-blocking mode (DMA) using | |
HAL_I2C_Slave_Receive_DMA() | |
(+) At reception end of transfer, HAL_I2C_SlaveRxCpltCallback() is executed and user can | |
add his own code by customization of function pointer HAL_I2C_SlaveRxCpltCallback() | |
(+) In case of transfer Error, HAL_I2C_ErrorCallback() function is executed and user can | |
add his own code by customization of function pointer HAL_I2C_ErrorCallback() | |
(+) Abort a master I2C process communication with Interrupt using HAL_I2C_Master_Abort_IT() | |
(+) End of abort process, HAL_I2C_MasterRxCpltCallback() or HAL_I2C_MasterTxCpltCallback() is executed and user can | |
add his own code by customization of function pointer HAL_I2C_MasterRxCpltCallback() or HAL_I2C_MasterTxCpltCallback() | |
(+) Discard a slave I2C process communication using __HAL_I2C_GENERATE_NACK() macro. | |
This action will inform Master to generate a Stop condition to discard the communication. | |
*** DMA mode IO MEM operation *** | |
================================= | |
[..] | |
(+) Write an amount of data in non-blocking mode with DMA to a specific memory address using | |
HAL_I2C_Mem_Write_DMA() | |
(+) At Memory end of write transfer, HAL_I2C_MemTxCpltCallback() is executed and user can | |
add his own code by customization of function pointer HAL_I2C_MemTxCpltCallback() | |
(+) Read an amount of data in non-blocking mode with DMA from a specific memory address using | |
HAL_I2C_Mem_Read_DMA() | |
(+) At Memory end of read transfer, HAL_I2C_MemRxCpltCallback() is executed and user can | |
add his own code by customization of function pointer HAL_I2C_MemRxCpltCallback() | |
(+) In case of transfer Error, HAL_I2C_ErrorCallback() function is executed and user can | |
add his own code by customization of function pointer HAL_I2C_ErrorCallback() | |
*** I2C HAL driver macros list *** | |
================================== | |
[..] | |
Below the list of most used macros in I2C HAL driver. | |
(+) __HAL_I2C_ENABLE: Enable the I2C peripheral | |
(+) __HAL_I2C_DISABLE: Disable the I2C peripheral | |
(+) __HAL_I2C_GENERATE_NACK: Generate a Non-Acknowledge I2C peripheral in Slave mode | |
(+) __HAL_I2C_GET_FLAG: Check whether the specified I2C flag is set or not | |
(+) __HAL_I2C_CLEAR_FLAG: Clear the specified I2C pending flag | |
(+) __HAL_I2C_ENABLE_IT: Enable the specified I2C interrupt | |
(+) __HAL_I2C_DISABLE_IT: Disable the specified I2C interrupt | |
[..] | |
(@) You can refer to the I2C HAL driver header file for more useful macros | |
@endverbatim | |
****************************************************************************** | |
* @attention | |
* | |
* <h2><center>© COPYRIGHT(c) 2016 STMicroelectronics</center></h2> | |
* | |
* Redistribution and use in source and binary forms, with or without modification, | |
* are permitted provided that the following conditions are met: | |
* 1. Redistributions of source code must retain the above copyright notice, | |
* this list of conditions and the following disclaimer. | |
* 2. Redistributions in binary form must reproduce the above copyright notice, | |
* this list of conditions and the following disclaimer in the documentation | |
* and/or other materials provided with the distribution. | |
* 3. Neither the name of STMicroelectronics nor the names of its contributors | |
* may be used to endorse or promote products derived from this software | |
* without specific prior written permission. | |
* | |
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" | |
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE | |
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE | |
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE | |
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL | |
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR | |
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER | |
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, | |
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE | |
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. | |
* | |
****************************************************************************** | |
*/ | |
/* Includes ------------------------------------------------------------------*/ | |
#include "stm32f7xx_hal.h" | |
/** @addtogroup STM32F7xx_HAL_Driver | |
* @{ | |
*/ | |
/** @defgroup I2C I2C | |
* @brief I2C HAL module driver | |
* @{ | |
*/ | |
#ifdef HAL_I2C_MODULE_ENABLED | |
/* Private typedef -----------------------------------------------------------*/ | |
/* Private define ------------------------------------------------------------*/ | |
/** @defgroup I2C_Private_Define I2C Private Define | |
* @{ | |
*/ | |
#define TIMING_CLEAR_MASK ((uint32_t)0xF0FFFFFFU) /*!< I2C TIMING clear register Mask */ | |
#define I2C_TIMEOUT_ADDR ((uint32_t)10000U) /*!< 10 s */ | |
#define I2C_TIMEOUT_BUSY ((uint32_t)25U) /*!< 25 ms */ | |
#define I2C_TIMEOUT_DIR ((uint32_t)25U) /*!< 25 ms */ | |
#define I2C_TIMEOUT_RXNE ((uint32_t)25U) /*!< 25 ms */ | |
#define I2C_TIMEOUT_STOPF ((uint32_t)25U) /*!< 25 ms */ | |
#define I2C_TIMEOUT_TC ((uint32_t)25U) /*!< 25 ms */ | |
#define I2C_TIMEOUT_TCR ((uint32_t)25U) /*!< 25 ms */ | |
#define I2C_TIMEOUT_TXIS ((uint32_t)25U) /*!< 25 ms */ | |
#define I2C_TIMEOUT_FLAG ((uint32_t)25U) /*!< 25 ms */ | |
#define MAX_NBYTE_SIZE 255U | |
#define SlaveAddr_SHIFT 7U | |
#define SlaveAddr_MSK 0x06U | |
/* Private define for @ref PreviousState usage */ | |
#define I2C_STATE_MSK ((uint32_t)((HAL_I2C_STATE_BUSY_TX | HAL_I2C_STATE_BUSY_RX) & (~((uint32_t)HAL_I2C_STATE_READY)))) /*!< Mask State define, keep only RX and TX bits */ | |
#define I2C_STATE_NONE ((uint32_t)(HAL_I2C_MODE_NONE)) /*!< Default Value */ | |
#define I2C_STATE_MASTER_BUSY_TX ((uint32_t)((HAL_I2C_STATE_BUSY_TX & I2C_STATE_MSK) | HAL_I2C_MODE_MASTER)) /*!< Master Busy TX, combinaison of State LSB and Mode enum */ | |
#define I2C_STATE_MASTER_BUSY_RX ((uint32_t)((HAL_I2C_STATE_BUSY_RX & I2C_STATE_MSK) | HAL_I2C_MODE_MASTER)) /*!< Master Busy RX, combinaison of State LSB and Mode enum */ | |
#define I2C_STATE_SLAVE_BUSY_TX ((uint32_t)((HAL_I2C_STATE_BUSY_TX & I2C_STATE_MSK) | HAL_I2C_MODE_SLAVE)) /*!< Slave Busy TX, combinaison of State LSB and Mode enum */ | |
#define I2C_STATE_SLAVE_BUSY_RX ((uint32_t)((HAL_I2C_STATE_BUSY_RX & I2C_STATE_MSK) | HAL_I2C_MODE_SLAVE)) /*!< Slave Busy RX, combinaison of State LSB and Mode enum */ | |
#define I2C_STATE_MEM_BUSY_TX ((uint32_t)((HAL_I2C_STATE_BUSY_TX & I2C_STATE_MSK) | HAL_I2C_MODE_MEM)) /*!< Memory Busy TX, combinaison of State LSB and Mode enum */ | |
#define I2C_STATE_MEM_BUSY_RX ((uint32_t)((HAL_I2C_STATE_BUSY_RX & I2C_STATE_MSK) | HAL_I2C_MODE_MEM)) /*!< Memory Busy RX, combinaison of State LSB and Mode enum */ | |
/* Private define to centralize the enable/disable of Interrupts */ | |
#define I2C_XFER_TX_IT ((uint32_t)0x00000001) | |
#define I2C_XFER_RX_IT ((uint32_t)0x00000002) | |
#define I2C_XFER_LISTEN_IT ((uint32_t)0x00000004) | |
#define I2C_XFER_ERROR_IT ((uint32_t)0x00000011) | |
#define I2C_XFER_CPLT_IT ((uint32_t)0x00000012) | |
#define I2C_XFER_RELOAD_IT ((uint32_t)0x00000012) | |
/** | |
* @} | |
*/ | |
/* Private macro -------------------------------------------------------------*/ | |
#define I2C_GET_DMA_REMAIN_DATA(__HANDLE__) ((((__HANDLE__)->State) == HAL_I2C_STATE_BUSY_TX) ? \ | |
((uint32_t)((__HANDLE__)->hdmatx->Instance->NDTR)) : \ | |
((uint32_t)((__HANDLE__)->hdmarx->Instance->NDTR))) | |
/* Private variables ---------------------------------------------------------*/ | |
/* Private function prototypes -----------------------------------------------*/ | |
/** @defgroup I2C_Private_Functions I2C Private Functions | |
* @{ | |
*/ | |
/* Private functions to handle DMA transfer */ | |
static void I2C_DMAMasterTransmitCplt(DMA_HandleTypeDef *hdma); | |
static void I2C_DMAMasterReceiveCplt(DMA_HandleTypeDef *hdma); | |
static void I2C_DMASlaveTransmitCplt(DMA_HandleTypeDef *hdma); | |
static void I2C_DMASlaveReceiveCplt(DMA_HandleTypeDef *hdma); | |
static void I2C_DMAError(DMA_HandleTypeDef *hdma); | |
static void I2C_DMAAbort(DMA_HandleTypeDef *hdma); | |
/* Private functions to handle IT transfer */ | |
static void I2C_ITAddrCplt(I2C_HandleTypeDef *hi2c, uint32_t ITFlags); | |
static void I2C_ITMasterSequentialCplt(I2C_HandleTypeDef *hi2c); | |
static void I2C_ITSlaveSequentialCplt(I2C_HandleTypeDef *hi2c); | |
static void I2C_ITMasterCplt(I2C_HandleTypeDef *hi2c, uint32_t ITFlags); | |
static void I2C_ITSlaveCplt(I2C_HandleTypeDef *hi2c, uint32_t ITFlags); | |
static void I2C_ITListenCplt(I2C_HandleTypeDef *hi2c, uint32_t ITFlags); | |
static void I2C_ITError(I2C_HandleTypeDef *hi2c, uint32_t ErrorCode); | |
/* Private functions to handle IT transfer */ | |
static HAL_StatusTypeDef I2C_RequestMemoryWrite(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress, uint16_t MemAddSize, uint32_t Timeout, uint32_t Tickstart); | |
static HAL_StatusTypeDef I2C_RequestMemoryRead(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress, uint16_t MemAddSize, uint32_t Timeout, uint32_t Tickstart); | |
/* Private functions for I2C transfer IRQ handler */ | |
static HAL_StatusTypeDef I2C_Master_ISR_IT(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, uint32_t ITSources); | |
static HAL_StatusTypeDef I2C_Slave_ISR_IT(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, uint32_t ITSources); | |
static HAL_StatusTypeDef I2C_Master_ISR_DMA(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, uint32_t ITSources); | |
static HAL_StatusTypeDef I2C_Slave_ISR_DMA(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, uint32_t ITSources); | |
/* Private functions to handle flags during polling transfer */ | |
static HAL_StatusTypeDef I2C_WaitOnFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Flag, FlagStatus Status, uint32_t Timeout, uint32_t Tickstart); | |
static HAL_StatusTypeDef I2C_WaitOnTXISFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Timeout, uint32_t Tickstart); | |
static HAL_StatusTypeDef I2C_WaitOnRXNEFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Timeout, uint32_t Tickstart); | |
static HAL_StatusTypeDef I2C_WaitOnSTOPFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Timeout, uint32_t Tickstart); | |
static HAL_StatusTypeDef I2C_IsAcknowledgeFailed(I2C_HandleTypeDef *hi2c, uint32_t Timeout, uint32_t Tickstart); | |
/* Private functions to centralize the enable/disable of Interrupts */ | |
static HAL_StatusTypeDef I2C_Enable_IRQ(I2C_HandleTypeDef *hi2c, uint16_t InterruptRequest); | |
static HAL_StatusTypeDef I2C_Disable_IRQ(I2C_HandleTypeDef *hi2c, uint16_t InterruptRequest); | |
/* Private functions to flush TXDR register */ | |
static void I2C_Flush_TXDR(I2C_HandleTypeDef *hi2c); | |
/* Private functions to handle start, restart or stop a transfer */ | |
static void I2C_TransferConfig(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t Size, uint32_t Mode, uint32_t Request); | |
/** | |
* @} | |
*/ | |
/* Exported functions --------------------------------------------------------*/ | |
/** @defgroup I2C_Exported_Functions I2C Exported Functions | |
* @{ | |
*/ | |
/** @defgroup I2C_Exported_Functions_Group1 Initialization and de-initialization functions | |
* @brief Initialization and Configuration functions | |
* | |
@verbatim | |
=============================================================================== | |
##### Initialization and de-initialization functions ##### | |
=============================================================================== | |
[..] This subsection provides a set of functions allowing to initialize and | |
deinitialize the I2Cx peripheral: | |
(+) User must Implement HAL_I2C_MspInit() function in which he configures | |
all related peripherals resources (CLOCK, GPIO, DMA, IT and NVIC ). | |
(+) Call the function HAL_I2C_Init() to configure the selected device with | |
the selected configuration: | |
(++) Clock Timing | |
(++) Own Address 1 | |
(++) Addressing mode (Master, Slave) | |
(++) Dual Addressing mode | |
(++) Own Address 2 | |
(++) Own Address 2 Mask | |
(++) General call mode | |
(++) Nostretch mode | |
(+) Call the function HAL_I2C_DeInit() to restore the default configuration | |
of the selected I2Cx peripheral. | |
@endverbatim | |
* @{ | |
*/ | |
/** | |
* @brief Initializes the I2C according to the specified parameters | |
* in the I2C_InitTypeDef and initialize the associated handle. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_I2C_Init(I2C_HandleTypeDef *hi2c) | |
{ | |
/* Check the I2C handle allocation */ | |
if(hi2c == NULL) | |
{ | |
return HAL_ERROR; | |
} | |
/* Check the parameters */ | |
assert_param(IS_I2C_ALL_INSTANCE(hi2c->Instance)); | |
assert_param(IS_I2C_OWN_ADDRESS1(hi2c->Init.OwnAddress1)); | |
assert_param(IS_I2C_ADDRESSING_MODE(hi2c->Init.AddressingMode)); | |
assert_param(IS_I2C_DUAL_ADDRESS(hi2c->Init.DualAddressMode)); | |
assert_param(IS_I2C_OWN_ADDRESS2(hi2c->Init.OwnAddress2)); | |
assert_param(IS_I2C_OWN_ADDRESS2_MASK(hi2c->Init.OwnAddress2Masks)); | |
assert_param(IS_I2C_GENERAL_CALL(hi2c->Init.GeneralCallMode)); | |
assert_param(IS_I2C_NO_STRETCH(hi2c->Init.NoStretchMode)); | |
if(hi2c->State == HAL_I2C_STATE_RESET) | |
{ | |
/* Allocate lock resource and initialize it */ | |
hi2c->Lock = HAL_UNLOCKED; | |
/* Init the low level hardware : GPIO, CLOCK, CORTEX...etc */ | |
HAL_I2C_MspInit(hi2c); | |
} | |
hi2c->State = HAL_I2C_STATE_BUSY; | |
/* Disable the selected I2C peripheral */ | |
__HAL_I2C_DISABLE(hi2c); | |
/*---------------------------- I2Cx TIMINGR Configuration ------------------*/ | |
/* Configure I2Cx: Frequency range */ | |
hi2c->Instance->TIMINGR = hi2c->Init.Timing & TIMING_CLEAR_MASK; | |
/*---------------------------- I2Cx OAR1 Configuration ---------------------*/ | |
/* Configure I2Cx: Own Address1 and ack own address1 mode */ | |
hi2c->Instance->OAR1 &= ~I2C_OAR1_OA1EN; | |
if(hi2c->Init.OwnAddress1 != 0) | |
{ | |
if(hi2c->Init.AddressingMode == I2C_ADDRESSINGMODE_7BIT) | |
{ | |
hi2c->Instance->OAR1 = (I2C_OAR1_OA1EN | hi2c->Init.OwnAddress1); | |
} | |
else /* I2C_ADDRESSINGMODE_10BIT */ | |
{ | |
hi2c->Instance->OAR1 = (I2C_OAR1_OA1EN | I2C_OAR1_OA1MODE | hi2c->Init.OwnAddress1); | |
} | |
} | |
/*---------------------------- I2Cx CR2 Configuration ----------------------*/ | |
/* Configure I2Cx: Addressing Master mode */ | |
if(hi2c->Init.AddressingMode == I2C_ADDRESSINGMODE_10BIT) | |
{ | |
hi2c->Instance->CR2 = (I2C_CR2_ADD10); | |
} | |
/* Enable the AUTOEND by default, and enable NACK (should be disable only during Slave process */ | |
hi2c->Instance->CR2 |= (I2C_CR2_AUTOEND | I2C_CR2_NACK); | |
/*---------------------------- I2Cx OAR2 Configuration ---------------------*/ | |
/* Configure I2Cx: Dual mode and Own Address2 */ | |
hi2c->Instance->OAR2 = (hi2c->Init.DualAddressMode | hi2c->Init.OwnAddress2 | (hi2c->Init.OwnAddress2Masks << 8)); | |
/*---------------------------- I2Cx CR1 Configuration ----------------------*/ | |
/* Configure I2Cx: Generalcall and NoStretch mode */ | |
hi2c->Instance->CR1 = (hi2c->Init.GeneralCallMode | hi2c->Init.NoStretchMode); | |
/* Enable the selected I2C peripheral */ | |
__HAL_I2C_ENABLE(hi2c); | |
hi2c->ErrorCode = HAL_I2C_ERROR_NONE; | |
hi2c->State = HAL_I2C_STATE_READY; | |
hi2c->PreviousState = I2C_STATE_NONE; | |
hi2c->Mode = HAL_I2C_MODE_NONE; | |
return HAL_OK; | |
} | |
/** | |
* @brief DeInitialize the I2C peripheral. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_I2C_DeInit(I2C_HandleTypeDef *hi2c) | |
{ | |
/* Check the I2C handle allocation */ | |
if(hi2c == NULL) | |
{ | |
return HAL_ERROR; | |
} | |
/* Check the parameters */ | |
assert_param(IS_I2C_ALL_INSTANCE(hi2c->Instance)); | |
hi2c->State = HAL_I2C_STATE_BUSY; | |
/* Disable the I2C Peripheral Clock */ | |
__HAL_I2C_DISABLE(hi2c); | |
/* DeInit the low level hardware: GPIO, CLOCK, NVIC */ | |
HAL_I2C_MspDeInit(hi2c); | |
hi2c->ErrorCode = HAL_I2C_ERROR_NONE; | |
hi2c->State = HAL_I2C_STATE_RESET; | |
hi2c->PreviousState = I2C_STATE_NONE; | |
hi2c->Mode = HAL_I2C_MODE_NONE; | |
/* Release Lock */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_OK; | |
} | |
/** | |
* @brief Initialize the I2C MSP. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @retval None | |
*/ | |
__weak void HAL_I2C_MspInit(I2C_HandleTypeDef *hi2c) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(hi2c); | |
/* NOTE : This function should not be modified, when the callback is needed, | |
the HAL_I2C_MspInit could be implemented in the user file | |
*/ | |
} | |
/** | |
* @brief DeInitialize the I2C MSP. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @retval None | |
*/ | |
__weak void HAL_I2C_MspDeInit(I2C_HandleTypeDef *hi2c) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(hi2c); | |
/* NOTE : This function should not be modified, when the callback is needed, | |
the HAL_I2C_MspDeInit could be implemented in the user file | |
*/ | |
} | |
/** | |
* @} | |
*/ | |
/** @defgroup I2C_Exported_Functions_Group2 Input and Output operation functions | |
* @brief Data transfers functions | |
* | |
@verbatim | |
=============================================================================== | |
##### IO operation functions ##### | |
=============================================================================== | |
[..] | |
This subsection provides a set of functions allowing to manage the I2C data | |
transfers. | |
(#) There are two modes of transfer: | |
(++) Blocking mode : The communication is performed in the polling mode. | |
The status of all data processing is returned by the same function | |
after finishing transfer. | |
(++) No-Blocking mode : The communication is performed using Interrupts | |
or DMA. These functions return the status of the transfer startup. | |
The end of the data processing will be indicated through the | |
dedicated I2C IRQ when using Interrupt mode or the DMA IRQ when | |
using DMA mode. | |
(#) Blocking mode functions are : | |
(++) HAL_I2C_Master_Transmit() | |
(++) HAL_I2C_Master_Receive() | |
(++) HAL_I2C_Slave_Transmit() | |
(++) HAL_I2C_Slave_Receive() | |
(++) HAL_I2C_Mem_Write() | |
(++) HAL_I2C_Mem_Read() | |
(++) HAL_I2C_IsDeviceReady() | |
(#) No-Blocking mode functions with Interrupt are : | |
(++) HAL_I2C_Master_Transmit_IT() | |
(++) HAL_I2C_Master_Receive_IT() | |
(++) HAL_I2C_Slave_Transmit_IT() | |
(++) HAL_I2C_Slave_Receive_IT() | |
(++) HAL_I2C_Mem_Write_IT() | |
(++) HAL_I2C_Mem_Read_IT() | |
(#) No-Blocking mode functions with DMA are : | |
(++) HAL_I2C_Master_Transmit_DMA() | |
(++) HAL_I2C_Master_Receive_DMA() | |
(++) HAL_I2C_Slave_Transmit_DMA() | |
(++) HAL_I2C_Slave_Receive_DMA() | |
(++) HAL_I2C_Mem_Write_DMA() | |
(++) HAL_I2C_Mem_Read_DMA() | |
(#) A set of Transfer Complete Callbacks are provided in non Blocking mode: | |
(++) HAL_I2C_MemTxCpltCallback() | |
(++) HAL_I2C_MemRxCpltCallback() | |
(++) HAL_I2C_MasterTxCpltCallback() | |
(++) HAL_I2C_MasterRxCpltCallback() | |
(++) HAL_I2C_SlaveTxCpltCallback() | |
(++) HAL_I2C_SlaveRxCpltCallback() | |
(++) HAL_I2C_ErrorCallback() | |
@endverbatim | |
* @{ | |
*/ | |
/** | |
* @brief Transmits in master mode an amount of data in blocking mode. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param DevAddress: Target device address | |
* @param pData: Pointer to data buffer | |
* @param Size: Amount of data to be sent | |
* @param Timeout: Timeout duration | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_I2C_Master_Transmit(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, uint16_t Size, uint32_t Timeout) | |
{ | |
uint32_t tickstart = 0; | |
if(hi2c->State == HAL_I2C_STATE_READY) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hi2c); | |
/* Init tickstart for timeout management*/ | |
tickstart = HAL_GetTick(); | |
if(I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_BUSY, SET, I2C_TIMEOUT_BUSY, tickstart) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
hi2c->State = HAL_I2C_STATE_BUSY_TX; | |
hi2c->Mode = HAL_I2C_MODE_MASTER; | |
hi2c->ErrorCode = HAL_I2C_ERROR_NONE; | |
/* Prepare transfer parameters */ | |
hi2c->pBuffPtr = pData; | |
hi2c->XferCount = Size; | |
hi2c->XferISR = NULL; | |
/* Send Slave Address */ | |
/* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE and generate RESTART */ | |
if(hi2c->XferCount > MAX_NBYTE_SIZE) | |
{ | |
hi2c->XferSize = MAX_NBYTE_SIZE; | |
I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_RELOAD_MODE, I2C_GENERATE_START_WRITE); | |
} | |
else | |
{ | |
hi2c->XferSize = hi2c->XferCount; | |
I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_AUTOEND_MODE, I2C_GENERATE_START_WRITE); | |
} | |
while(hi2c->XferSize > 0) | |
{ | |
/* Wait until TXIS flag is set */ | |
if(I2C_WaitOnTXISFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK) | |
{ | |
if(hi2c->ErrorCode == HAL_I2C_ERROR_AF) | |
{ | |
return HAL_ERROR; | |
} | |
else | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
/* Write data to TXDR */ | |
hi2c->Instance->TXDR = (*hi2c->pBuffPtr++); | |
hi2c->XferCount--; | |
hi2c->XferSize--; | |
if((hi2c->XferSize == 0) && (hi2c->XferCount!=0)) | |
{ | |
/* Wait until TCR flag is set */ | |
if(I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_TCR, RESET, Timeout, tickstart) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
if(hi2c->XferCount > MAX_NBYTE_SIZE) | |
{ | |
hi2c->XferSize = MAX_NBYTE_SIZE; | |
I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_RELOAD_MODE, I2C_NO_STARTSTOP); | |
} | |
else | |
{ | |
hi2c->XferSize = hi2c->XferCount; | |
I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_AUTOEND_MODE, I2C_NO_STARTSTOP); | |
} | |
} | |
} | |
/* No need to Check TC flag, with AUTOEND mode the stop is automatically generated */ | |
/* Wait until STOPF flag is set */ | |
if(I2C_WaitOnSTOPFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK) | |
{ | |
if(hi2c->ErrorCode == HAL_I2C_ERROR_AF) | |
{ | |
return HAL_ERROR; | |
} | |
else | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
/* Clear STOP Flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF); | |
/* Clear Configuration Register 2 */ | |
I2C_RESET_CR2(hi2c); | |
hi2c->State = HAL_I2C_STATE_READY; | |
hi2c->Mode = HAL_I2C_MODE_NONE; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Receives in master mode an amount of data in blocking mode. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param DevAddress: Target device address | |
* @param pData: Pointer to data buffer | |
* @param Size: Amount of data to be sent | |
* @param Timeout: Timeout duration | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_I2C_Master_Receive(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, uint16_t Size, uint32_t Timeout) | |
{ | |
uint32_t tickstart = 0; | |
if(hi2c->State == HAL_I2C_STATE_READY) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hi2c); | |
/* Init tickstart for timeout management*/ | |
tickstart = HAL_GetTick(); | |
if(I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_BUSY, SET, I2C_TIMEOUT_BUSY, tickstart) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
hi2c->State = HAL_I2C_STATE_BUSY_RX; | |
hi2c->Mode = HAL_I2C_MODE_MASTER; | |
hi2c->ErrorCode = HAL_I2C_ERROR_NONE; | |
/* Prepare transfer parameters */ | |
hi2c->pBuffPtr = pData; | |
hi2c->XferCount = Size; | |
hi2c->XferISR = NULL; | |
/* Send Slave Address */ | |
/* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE and generate RESTART */ | |
if(hi2c->XferCount > MAX_NBYTE_SIZE) | |
{ | |
hi2c->XferSize = MAX_NBYTE_SIZE; | |
I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_RELOAD_MODE, I2C_GENERATE_START_READ); | |
} | |
else | |
{ | |
hi2c->XferSize = hi2c->XferCount; | |
I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_AUTOEND_MODE, I2C_GENERATE_START_READ); | |
} | |
while(hi2c->XferSize > 0) | |
{ | |
/* Wait until RXNE flag is set */ | |
if(I2C_WaitOnRXNEFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK) | |
{ | |
if(hi2c->ErrorCode == HAL_I2C_ERROR_AF) | |
{ | |
return HAL_ERROR; | |
} | |
else | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
/* Read data from RXDR */ | |
(*hi2c->pBuffPtr++) = hi2c->Instance->RXDR; | |
hi2c->XferSize--; | |
hi2c->XferCount--; | |
if((hi2c->XferSize == 0) && (hi2c->XferCount != 0)) | |
{ | |
/* Wait until TCR flag is set */ | |
if(I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_TCR, RESET, Timeout, tickstart) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
if(hi2c->XferCount > MAX_NBYTE_SIZE) | |
{ | |
hi2c->XferSize = MAX_NBYTE_SIZE; | |
I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_RELOAD_MODE, I2C_NO_STARTSTOP); | |
} | |
else | |
{ | |
hi2c->XferSize = hi2c->XferCount; | |
I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_AUTOEND_MODE, I2C_NO_STARTSTOP); | |
} | |
} | |
} | |
/* No need to Check TC flag, with AUTOEND mode the stop is automatically generated */ | |
/* Wait until STOPF flag is set */ | |
if(I2C_WaitOnSTOPFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK) | |
{ | |
if(hi2c->ErrorCode == HAL_I2C_ERROR_AF) | |
{ | |
return HAL_ERROR; | |
} | |
else | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
/* Clear STOP Flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF); | |
/* Clear Configuration Register 2 */ | |
I2C_RESET_CR2(hi2c); | |
hi2c->State = HAL_I2C_STATE_READY; | |
hi2c->Mode = HAL_I2C_MODE_NONE; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Transmits in slave mode an amount of data in blocking mode. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param pData: Pointer to data buffer | |
* @param Size: Amount of data to be sent | |
* @param Timeout: Timeout duration | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_I2C_Slave_Transmit(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size, uint32_t Timeout) | |
{ | |
uint32_t tickstart = 0; | |
if(hi2c->State == HAL_I2C_STATE_READY) | |
{ | |
if((pData == NULL ) || (Size == 0)) | |
{ | |
return HAL_ERROR; | |
} | |
/* Process Locked */ | |
__HAL_LOCK(hi2c); | |
/* Init tickstart for timeout management*/ | |
tickstart = HAL_GetTick(); | |
hi2c->State = HAL_I2C_STATE_BUSY_TX; | |
hi2c->Mode = HAL_I2C_MODE_SLAVE; | |
hi2c->ErrorCode = HAL_I2C_ERROR_NONE; | |
/* Prepare transfer parameters */ | |
hi2c->pBuffPtr = pData; | |
hi2c->XferCount = Size; | |
hi2c->XferISR = NULL; | |
/* Enable Address Acknowledge */ | |
hi2c->Instance->CR2 &= ~I2C_CR2_NACK; | |
/* Wait until ADDR flag is set */ | |
if(I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_ADDR, RESET, Timeout, tickstart) != HAL_OK) | |
{ | |
/* Disable Address Acknowledge */ | |
hi2c->Instance->CR2 |= I2C_CR2_NACK; | |
return HAL_TIMEOUT; | |
} | |
/* Clear ADDR flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c,I2C_FLAG_ADDR); | |
/* If 10bit addressing mode is selected */ | |
if(hi2c->Init.AddressingMode == I2C_ADDRESSINGMODE_10BIT) | |
{ | |
/* Wait until ADDR flag is set */ | |
if(I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_ADDR, RESET, Timeout, tickstart) != HAL_OK) | |
{ | |
/* Disable Address Acknowledge */ | |
hi2c->Instance->CR2 |= I2C_CR2_NACK; | |
return HAL_TIMEOUT; | |
} | |
/* Clear ADDR flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c,I2C_FLAG_ADDR); | |
} | |
/* Wait until DIR flag is set Transmitter mode */ | |
if(I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_DIR, RESET, Timeout, tickstart) != HAL_OK) | |
{ | |
/* Disable Address Acknowledge */ | |
hi2c->Instance->CR2 |= I2C_CR2_NACK; | |
return HAL_TIMEOUT; | |
} | |
while(hi2c->XferCount > 0) | |
{ | |
/* Wait until TXIS flag is set */ | |
if(I2C_WaitOnTXISFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK) | |
{ | |
/* Disable Address Acknowledge */ | |
hi2c->Instance->CR2 |= I2C_CR2_NACK; | |
if(hi2c->ErrorCode == HAL_I2C_ERROR_AF) | |
{ | |
return HAL_ERROR; | |
} | |
else | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
/* Write data to TXDR */ | |
hi2c->Instance->TXDR = (*hi2c->pBuffPtr++); | |
hi2c->XferCount--; | |
} | |
/* Wait until STOP flag is set */ | |
if(I2C_WaitOnSTOPFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK) | |
{ | |
/* Disable Address Acknowledge */ | |
hi2c->Instance->CR2 |= I2C_CR2_NACK; | |
if(hi2c->ErrorCode == HAL_I2C_ERROR_AF) | |
{ | |
/* Normal use case for Transmitter mode */ | |
/* A NACK is generated to confirm the end of transfer */ | |
hi2c->ErrorCode = HAL_I2C_ERROR_NONE; | |
} | |
else | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
/* Clear STOP flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c,I2C_FLAG_STOPF); | |
/* Wait until BUSY flag is reset */ | |
if(I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_BUSY, SET, Timeout, tickstart) != HAL_OK) | |
{ | |
/* Disable Address Acknowledge */ | |
hi2c->Instance->CR2 |= I2C_CR2_NACK; | |
return HAL_TIMEOUT; | |
} | |
/* Disable Address Acknowledge */ | |
hi2c->Instance->CR2 |= I2C_CR2_NACK; | |
hi2c->State = HAL_I2C_STATE_READY; | |
hi2c->Mode = HAL_I2C_MODE_NONE; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Receive in slave mode an amount of data in blocking mode | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param pData: Pointer to data buffer | |
* @param Size: Amount of data to be sent | |
* @param Timeout: Timeout duration | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_I2C_Slave_Receive(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size, uint32_t Timeout) | |
{ | |
uint32_t tickstart = 0; | |
if(hi2c->State == HAL_I2C_STATE_READY) | |
{ | |
if((pData == NULL ) || (Size == 0)) | |
{ | |
return HAL_ERROR; | |
} | |
/* Process Locked */ | |
__HAL_LOCK(hi2c); | |
/* Init tickstart for timeout management*/ | |
tickstart = HAL_GetTick(); | |
hi2c->State = HAL_I2C_STATE_BUSY_RX; | |
hi2c->Mode = HAL_I2C_MODE_SLAVE; | |
hi2c->ErrorCode = HAL_I2C_ERROR_NONE; | |
/* Prepare transfer parameters */ | |
hi2c->pBuffPtr = pData; | |
hi2c->XferCount = Size; | |
hi2c->XferISR = NULL; | |
/* Enable Address Acknowledge */ | |
hi2c->Instance->CR2 &= ~I2C_CR2_NACK; | |
/* Wait until ADDR flag is set */ | |
if(I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_ADDR, RESET, Timeout, tickstart) != HAL_OK) | |
{ | |
/* Disable Address Acknowledge */ | |
hi2c->Instance->CR2 |= I2C_CR2_NACK; | |
return HAL_TIMEOUT; | |
} | |
/* Clear ADDR flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c,I2C_FLAG_ADDR); | |
/* Wait until DIR flag is reset Receiver mode */ | |
if(I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_DIR, SET, Timeout, tickstart) != HAL_OK) | |
{ | |
/* Disable Address Acknowledge */ | |
hi2c->Instance->CR2 |= I2C_CR2_NACK; | |
return HAL_TIMEOUT; | |
} | |
while(hi2c->XferCount > 0) | |
{ | |
/* Wait until RXNE flag is set */ | |
if(I2C_WaitOnRXNEFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK) | |
{ | |
/* Disable Address Acknowledge */ | |
hi2c->Instance->CR2 |= I2C_CR2_NACK; | |
/* Store Last receive data if any */ | |
if(__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_RXNE) == SET) | |
{ | |
/* Read data from RXDR */ | |
(*hi2c->pBuffPtr++) = hi2c->Instance->RXDR; | |
hi2c->XferCount--; | |
} | |
if(hi2c->ErrorCode == HAL_I2C_ERROR_TIMEOUT) | |
{ | |
return HAL_TIMEOUT; | |
} | |
else | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/* Read data from RXDR */ | |
(*hi2c->pBuffPtr++) = hi2c->Instance->RXDR; | |
hi2c->XferCount--; | |
} | |
/* Wait until STOP flag is set */ | |
if(I2C_WaitOnSTOPFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK) | |
{ | |
/* Disable Address Acknowledge */ | |
hi2c->Instance->CR2 |= I2C_CR2_NACK; | |
if(hi2c->ErrorCode == HAL_I2C_ERROR_AF) | |
{ | |
return HAL_ERROR; | |
} | |
else | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
/* Clear STOP flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c,I2C_FLAG_STOPF); | |
/* Wait until BUSY flag is reset */ | |
if(I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_BUSY, SET, Timeout, tickstart) != HAL_OK) | |
{ | |
/* Disable Address Acknowledge */ | |
hi2c->Instance->CR2 |= I2C_CR2_NACK; | |
return HAL_TIMEOUT; | |
} | |
/* Disable Address Acknowledge */ | |
hi2c->Instance->CR2 |= I2C_CR2_NACK; | |
hi2c->State = HAL_I2C_STATE_READY; | |
hi2c->Mode = HAL_I2C_MODE_NONE; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Transmit in master mode an amount of data in non-blocking mode with Interrupt | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param DevAddress: Target device address | |
* @param pData: Pointer to data buffer | |
* @param Size: Amount of data to be sent | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_I2C_Master_Transmit_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, uint16_t Size) | |
{ | |
uint32_t xfermode = 0; | |
if(hi2c->State == HAL_I2C_STATE_READY) | |
{ | |
if(__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_BUSY) == SET) | |
{ | |
return HAL_BUSY; | |
} | |
/* Process Locked */ | |
__HAL_LOCK(hi2c); | |
hi2c->State = HAL_I2C_STATE_BUSY_TX; | |
hi2c->Mode = HAL_I2C_MODE_MASTER; | |
hi2c->ErrorCode = HAL_I2C_ERROR_NONE; | |
/* Prepare transfer parameters */ | |
hi2c->pBuffPtr = pData; | |
hi2c->XferCount = Size; | |
hi2c->XferOptions = I2C_NO_OPTION_FRAME; | |
hi2c->XferISR = I2C_Master_ISR_IT; | |
if(hi2c->XferCount > MAX_NBYTE_SIZE) | |
{ | |
hi2c->XferSize = MAX_NBYTE_SIZE; | |
xfermode = I2C_RELOAD_MODE; | |
} | |
else | |
{ | |
hi2c->XferSize = hi2c->XferCount; | |
xfermode = I2C_AUTOEND_MODE; | |
} | |
/* Send Slave Address */ | |
/* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE */ | |
I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, xfermode, I2C_GENERATE_START_WRITE); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Note : The I2C interrupts must be enabled after unlocking current process | |
to avoid the risk of I2C interrupt handle execution before current | |
process unlock */ | |
/* Enable ERR, TC, STOP, NACK, TXI interrupt */ | |
/* possible to enable all of these */ | |
/* I2C_IT_ERRI | I2C_IT_TCI| I2C_IT_STOPI| I2C_IT_NACKI | I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */ | |
I2C_Enable_IRQ(hi2c, I2C_XFER_TX_IT); | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Receive in master mode an amount of data in non-blocking mode with Interrupt | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param DevAddress: Target device address | |
* @param pData: Pointer to data buffer | |
* @param Size: Amount of data to be sent | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_I2C_Master_Receive_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, uint16_t Size) | |
{ | |
uint32_t xfermode = 0; | |
if(hi2c->State == HAL_I2C_STATE_READY) | |
{ | |
if(__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_BUSY) == SET) | |
{ | |
return HAL_BUSY; | |
} | |
/* Process Locked */ | |
__HAL_LOCK(hi2c); | |
hi2c->State = HAL_I2C_STATE_BUSY_RX; | |
hi2c->Mode = HAL_I2C_MODE_MASTER; | |
hi2c->ErrorCode = HAL_I2C_ERROR_NONE; | |
/* Prepare transfer parameters */ | |
hi2c->pBuffPtr = pData; | |
hi2c->XferCount = Size; | |
hi2c->XferOptions = I2C_NO_OPTION_FRAME; | |
hi2c->XferISR = I2C_Master_ISR_IT; | |
if(hi2c->XferCount > MAX_NBYTE_SIZE) | |
{ | |
hi2c->XferSize = MAX_NBYTE_SIZE; | |
xfermode = I2C_RELOAD_MODE; | |
} | |
else | |
{ | |
hi2c->XferSize = hi2c->XferCount; | |
xfermode = I2C_AUTOEND_MODE; | |
} | |
/* Send Slave Address */ | |
/* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE */ | |
I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, xfermode, I2C_GENERATE_START_READ); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Note : The I2C interrupts must be enabled after unlocking current process | |
to avoid the risk of I2C interrupt handle execution before current | |
process unlock */ | |
/* Enable ERR, TC, STOP, NACK, RXI interrupt */ | |
/* possible to enable all of these */ | |
/* I2C_IT_ERRI | I2C_IT_TCI| I2C_IT_STOPI| I2C_IT_NACKI | I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */ | |
I2C_Enable_IRQ(hi2c, I2C_XFER_RX_IT); | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Transmit in slave mode an amount of data in non-blocking mode with Interrupt | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param pData: Pointer to data buffer | |
* @param Size: Amount of data to be sent | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_I2C_Slave_Transmit_IT(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size) | |
{ | |
if(hi2c->State == HAL_I2C_STATE_READY) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hi2c); | |
hi2c->State = HAL_I2C_STATE_BUSY_TX; | |
hi2c->Mode = HAL_I2C_MODE_SLAVE; | |
hi2c->ErrorCode = HAL_I2C_ERROR_NONE; | |
/* Enable Address Acknowledge */ | |
hi2c->Instance->CR2 &= ~I2C_CR2_NACK; | |
/* Prepare transfer parameters */ | |
hi2c->pBuffPtr = pData; | |
hi2c->XferCount = Size; | |
hi2c->XferSize = hi2c->XferCount; | |
hi2c->XferOptions = I2C_NO_OPTION_FRAME; | |
hi2c->XferISR = I2C_Slave_ISR_IT; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Note : The I2C interrupts must be enabled after unlocking current process | |
to avoid the risk of I2C interrupt handle execution before current | |
process unlock */ | |
/* Enable ERR, TC, STOP, NACK, TXI interrupt */ | |
/* possible to enable all of these */ | |
/* I2C_IT_ERRI | I2C_IT_TCI| I2C_IT_STOPI| I2C_IT_NACKI | I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */ | |
I2C_Enable_IRQ(hi2c, I2C_XFER_TX_IT | I2C_XFER_LISTEN_IT); | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Receive in slave mode an amount of data in non-blocking mode with Interrupt | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param pData: Pointer to data buffer | |
* @param Size: Amount of data to be sent | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_I2C_Slave_Receive_IT(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size) | |
{ | |
if(hi2c->State == HAL_I2C_STATE_READY) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hi2c); | |
hi2c->State = HAL_I2C_STATE_BUSY_RX; | |
hi2c->Mode = HAL_I2C_MODE_SLAVE; | |
hi2c->ErrorCode = HAL_I2C_ERROR_NONE; | |
/* Enable Address Acknowledge */ | |
hi2c->Instance->CR2 &= ~I2C_CR2_NACK; | |
/* Prepare transfer parameters */ | |
hi2c->pBuffPtr = pData; | |
hi2c->XferCount = Size; | |
hi2c->XferSize = hi2c->XferCount; | |
hi2c->XferOptions = I2C_NO_OPTION_FRAME; | |
hi2c->XferISR = I2C_Slave_ISR_IT; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Note : The I2C interrupts must be enabled after unlocking current process | |
to avoid the risk of I2C interrupt handle execution before current | |
process unlock */ | |
/* Enable ERR, TC, STOP, NACK, RXI interrupt */ | |
/* possible to enable all of these */ | |
/* I2C_IT_ERRI | I2C_IT_TCI| I2C_IT_STOPI| I2C_IT_NACKI | I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */ | |
I2C_Enable_IRQ(hi2c, I2C_XFER_RX_IT | I2C_XFER_LISTEN_IT); | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Transmit in master mode an amount of data in non-blocking mode with DMA | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param DevAddress: Target device address | |
* @param pData: Pointer to data buffer | |
* @param Size: Amount of data to be sent | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_I2C_Master_Transmit_DMA(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, uint16_t Size) | |
{ | |
uint32_t xfermode = 0; | |
if(hi2c->State == HAL_I2C_STATE_READY) | |
{ | |
if(__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_BUSY) == SET) | |
{ | |
return HAL_BUSY; | |
} | |
/* Process Locked */ | |
__HAL_LOCK(hi2c); | |
hi2c->State = HAL_I2C_STATE_BUSY_TX; | |
hi2c->Mode = HAL_I2C_MODE_MASTER; | |
hi2c->ErrorCode = HAL_I2C_ERROR_NONE; | |
/* Prepare transfer parameters */ | |
hi2c->pBuffPtr = pData; | |
hi2c->XferCount = Size; | |
hi2c->XferOptions = I2C_NO_OPTION_FRAME; | |
hi2c->XferISR = I2C_Master_ISR_DMA; | |
if(hi2c->XferCount > MAX_NBYTE_SIZE) | |
{ | |
hi2c->XferSize = MAX_NBYTE_SIZE; | |
xfermode = I2C_RELOAD_MODE; | |
} | |
else | |
{ | |
hi2c->XferSize = hi2c->XferCount; | |
xfermode = I2C_AUTOEND_MODE; | |
} | |
/* Set the I2C DMA transfer complete callback */ | |
hi2c->hdmatx->XferCpltCallback = I2C_DMAMasterTransmitCplt; | |
/* Set the DMA error callback */ | |
hi2c->hdmatx->XferErrorCallback = I2C_DMAError; | |
/* Set the unused DMA callbacks to NULL */ | |
hi2c->hdmatx->XferHalfCpltCallback = NULL; | |
hi2c->hdmatx->XferAbortCallback = NULL; | |
/* Enable the DMA channel */ | |
HAL_DMA_Start_IT(hi2c->hdmatx, (uint32_t)pData, (uint32_t)&hi2c->Instance->TXDR, hi2c->XferSize); | |
/* Send Slave Address */ | |
/* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE and generate RESTART */ | |
I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, xfermode, I2C_GENERATE_START_WRITE); | |
/* Update XferCount value */ | |
hi2c->XferCount -= hi2c->XferSize; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Note : The I2C interrupts must be enabled after unlocking current process | |
to avoid the risk of I2C interrupt handle execution before current | |
process unlock */ | |
/* Enable ERR and NACK interrupts */ | |
I2C_Enable_IRQ(hi2c, I2C_XFER_ERROR_IT); | |
/* Enable DMA Request */ | |
hi2c->Instance->CR1 |= I2C_CR1_TXDMAEN; | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Receive in master mode an amount of data in non-blocking mode with DMA | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param DevAddress: Target device address | |
* @param pData: Pointer to data buffer | |
* @param Size: Amount of data to be sent | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_I2C_Master_Receive_DMA(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, uint16_t Size) | |
{ | |
uint32_t xfermode = 0; | |
if(hi2c->State == HAL_I2C_STATE_READY) | |
{ | |
if(__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_BUSY) == SET) | |
{ | |
return HAL_BUSY; | |
} | |
/* Process Locked */ | |
__HAL_LOCK(hi2c); | |
hi2c->State = HAL_I2C_STATE_BUSY_RX; | |
hi2c->Mode = HAL_I2C_MODE_MASTER; | |
hi2c->ErrorCode = HAL_I2C_ERROR_NONE; | |
/* Prepare transfer parameters */ | |
hi2c->pBuffPtr = pData; | |
hi2c->XferCount = Size; | |
hi2c->XferOptions = I2C_NO_OPTION_FRAME; | |
hi2c->XferISR = I2C_Master_ISR_DMA; | |
if(hi2c->XferCount > MAX_NBYTE_SIZE) | |
{ | |
hi2c->XferSize = MAX_NBYTE_SIZE; | |
xfermode = I2C_RELOAD_MODE; | |
} | |
else | |
{ | |
hi2c->XferSize = hi2c->XferCount; | |
xfermode = I2C_AUTOEND_MODE; | |
} | |
if(hi2c->XferSize > 0) | |
{ | |
/* Set the I2C DMA transfer complete callback */ | |
hi2c->hdmarx->XferCpltCallback = I2C_DMAMasterReceiveCplt; | |
/* Set the DMA error callback */ | |
hi2c->hdmarx->XferErrorCallback = I2C_DMAError; | |
/* Set the unused DMA callbacks to NULL */ | |
hi2c->hdmarx->XferHalfCpltCallback = NULL; | |
hi2c->hdmarx->XferAbortCallback = NULL; | |
/* Enable the DMA channel */ | |
HAL_DMA_Start_IT(hi2c->hdmarx, (uint32_t)&hi2c->Instance->RXDR, (uint32_t)pData, hi2c->XferSize); | |
/* Send Slave Address */ | |
/* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE and generate RESTART */ | |
I2C_TransferConfig(hi2c,DevAddress,hi2c->XferSize, xfermode, I2C_GENERATE_START_READ); | |
/* Update XferCount value */ | |
hi2c->XferCount -= hi2c->XferSize; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Note : The I2C interrupts must be enabled after unlocking current process | |
to avoid the risk of I2C interrupt handle execution before current | |
process unlock */ | |
/* Enable ERR and NACK interrupts */ | |
I2C_Enable_IRQ(hi2c, I2C_XFER_ERROR_IT); | |
/* Enable DMA Request */ | |
hi2c->Instance->CR1 |= I2C_CR1_RXDMAEN; | |
} | |
else | |
{ | |
hi2c->State = HAL_I2C_STATE_READY; | |
hi2c->Mode = HAL_I2C_MODE_NONE; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
} | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Transmit in slave mode an amount of data in non-blocking mode with DMA | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param pData: Pointer to data buffer | |
* @param Size: Amount of data to be sent | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_I2C_Slave_Transmit_DMA(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size) | |
{ | |
if(hi2c->State == HAL_I2C_STATE_READY) | |
{ | |
if((pData == NULL) || (Size == 0)) | |
{ | |
return HAL_ERROR; | |
} | |
/* Process Locked */ | |
__HAL_LOCK(hi2c); | |
hi2c->State = HAL_I2C_STATE_BUSY_TX; | |
hi2c->Mode = HAL_I2C_MODE_SLAVE; | |
hi2c->ErrorCode = HAL_I2C_ERROR_NONE; | |
/* Prepare transfer parameters */ | |
hi2c->pBuffPtr = pData; | |
hi2c->XferCount = Size; | |
hi2c->XferSize = hi2c->XferCount; | |
hi2c->XferOptions = I2C_NO_OPTION_FRAME; | |
hi2c->XferISR = I2C_Slave_ISR_DMA; | |
/* Set the I2C DMA transfer complete callback */ | |
hi2c->hdmatx->XferCpltCallback = I2C_DMASlaveTransmitCplt; | |
/* Set the DMA error callback */ | |
hi2c->hdmatx->XferErrorCallback = I2C_DMAError; | |
/* Set the unused DMA callbacks to NULL */ | |
hi2c->hdmatx->XferHalfCpltCallback = NULL; | |
hi2c->hdmatx->XferAbortCallback = NULL; | |
/* Enable the DMA channel */ | |
HAL_DMA_Start_IT(hi2c->hdmatx, (uint32_t)pData, (uint32_t)&hi2c->Instance->TXDR, hi2c->XferSize); | |
/* Enable Address Acknowledge */ | |
hi2c->Instance->CR2 &= ~I2C_CR2_NACK; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Note : The I2C interrupts must be enabled after unlocking current process | |
to avoid the risk of I2C interrupt handle execution before current | |
process unlock */ | |
/* Enable ERR, STOP, NACK, ADDR interrupts */ | |
I2C_Enable_IRQ(hi2c, I2C_XFER_LISTEN_IT); | |
/* Enable DMA Request */ | |
hi2c->Instance->CR1 |= I2C_CR1_TXDMAEN; | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Receive in slave mode an amount of data in non-blocking mode with DMA | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param pData: Pointer to data buffer | |
* @param Size: Amount of data to be sent | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_I2C_Slave_Receive_DMA(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size) | |
{ | |
if(hi2c->State == HAL_I2C_STATE_READY) | |
{ | |
if((pData == NULL) || (Size == 0)) | |
{ | |
return HAL_ERROR; | |
} | |
/* Process Locked */ | |
__HAL_LOCK(hi2c); | |
hi2c->State = HAL_I2C_STATE_BUSY_RX; | |
hi2c->Mode = HAL_I2C_MODE_SLAVE; | |
hi2c->ErrorCode = HAL_I2C_ERROR_NONE; | |
/* Prepare transfer parameters */ | |
hi2c->pBuffPtr = pData; | |
hi2c->XferCount = Size; | |
hi2c->XferSize = hi2c->XferCount; | |
hi2c->XferOptions = I2C_NO_OPTION_FRAME; | |
hi2c->XferISR = I2C_Slave_ISR_DMA; | |
/* Set the I2C DMA transfer complete callback */ | |
hi2c->hdmarx->XferCpltCallback = I2C_DMASlaveReceiveCplt; | |
/* Set the DMA error callback */ | |
hi2c->hdmarx->XferErrorCallback = I2C_DMAError; | |
/* Set the unused DMA callbacks to NULL */ | |
hi2c->hdmarx->XferHalfCpltCallback = NULL; | |
hi2c->hdmarx->XferAbortCallback = NULL; | |
/* Enable the DMA channel */ | |
HAL_DMA_Start_IT(hi2c->hdmarx, (uint32_t)&hi2c->Instance->RXDR, (uint32_t)pData, hi2c->XferSize); | |
/* Enable Address Acknowledge */ | |
hi2c->Instance->CR2 &= ~I2C_CR2_NACK; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Note : The I2C interrupts must be enabled after unlocking current process | |
to avoid the risk of I2C interrupt handle execution before current | |
process unlock */ | |
/* Enable ERR, STOP, NACK, ADDR interrupts */ | |
I2C_Enable_IRQ(hi2c, I2C_XFER_LISTEN_IT); | |
/* Enable DMA Request */ | |
hi2c->Instance->CR1 |= I2C_CR1_RXDMAEN; | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Write an amount of data in blocking mode to a specific memory address | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param DevAddress: Target device address | |
* @param MemAddress: Internal memory address | |
* @param MemAddSize: Size of internal memory address | |
* @param pData: Pointer to data buffer | |
* @param Size: Amount of data to be sent | |
* @param Timeout: Timeout duration | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_I2C_Mem_Write(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress, uint16_t MemAddSize, uint8_t *pData, uint16_t Size, uint32_t Timeout) | |
{ | |
uint32_t tickstart = 0; | |
/* Check the parameters */ | |
assert_param(IS_I2C_MEMADD_SIZE(MemAddSize)); | |
if(hi2c->State == HAL_I2C_STATE_READY) | |
{ | |
if((pData == NULL) || (Size == 0)) | |
{ | |
return HAL_ERROR; | |
} | |
/* Process Locked */ | |
__HAL_LOCK(hi2c); | |
/* Init tickstart for timeout management*/ | |
tickstart = HAL_GetTick(); | |
if(I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_BUSY, SET, I2C_TIMEOUT_BUSY, tickstart) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
hi2c->State = HAL_I2C_STATE_BUSY_TX; | |
hi2c->Mode = HAL_I2C_MODE_MEM; | |
hi2c->ErrorCode = HAL_I2C_ERROR_NONE; | |
/* Prepare transfer parameters */ | |
hi2c->pBuffPtr = pData; | |
hi2c->XferCount = Size; | |
hi2c->XferISR = NULL; | |
/* Send Slave Address and Memory Address */ | |
if(I2C_RequestMemoryWrite(hi2c, DevAddress, MemAddress, MemAddSize, Timeout, tickstart) != HAL_OK) | |
{ | |
if(hi2c->ErrorCode == HAL_I2C_ERROR_AF) | |
{ | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_ERROR; | |
} | |
else | |
{ | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_TIMEOUT; | |
} | |
} | |
/* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE */ | |
if(hi2c->XferCount > MAX_NBYTE_SIZE) | |
{ | |
hi2c->XferSize = MAX_NBYTE_SIZE; | |
I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_RELOAD_MODE, I2C_NO_STARTSTOP); | |
} | |
else | |
{ | |
hi2c->XferSize = hi2c->XferCount; | |
I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_AUTOEND_MODE, I2C_NO_STARTSTOP); | |
} | |
do | |
{ | |
/* Wait until TXIS flag is set */ | |
if(I2C_WaitOnTXISFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK) | |
{ | |
if(hi2c->ErrorCode == HAL_I2C_ERROR_AF) | |
{ | |
return HAL_ERROR; | |
} | |
else | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
/* Write data to TXDR */ | |
hi2c->Instance->TXDR = (*hi2c->pBuffPtr++); | |
hi2c->XferCount--; | |
hi2c->XferSize--; | |
if((hi2c->XferSize == 0) && (hi2c->XferCount!=0)) | |
{ | |
/* Wait until TCR flag is set */ | |
if(I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_TCR, RESET, Timeout, tickstart) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
if(hi2c->XferCount > MAX_NBYTE_SIZE) | |
{ | |
hi2c->XferSize = MAX_NBYTE_SIZE; | |
I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_RELOAD_MODE, I2C_NO_STARTSTOP); | |
} | |
else | |
{ | |
hi2c->XferSize = hi2c->XferCount; | |
I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_AUTOEND_MODE, I2C_NO_STARTSTOP); | |
} | |
} | |
}while(hi2c->XferCount > 0); | |
/* No need to Check TC flag, with AUTOEND mode the stop is automatically generated */ | |
/* Wait until STOPF flag is reset */ | |
if(I2C_WaitOnSTOPFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK) | |
{ | |
if(hi2c->ErrorCode == HAL_I2C_ERROR_AF) | |
{ | |
return HAL_ERROR; | |
} | |
else | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
/* Clear STOP Flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF); | |
/* Clear Configuration Register 2 */ | |
I2C_RESET_CR2(hi2c); | |
hi2c->State = HAL_I2C_STATE_READY; | |
hi2c->Mode = HAL_I2C_MODE_NONE; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Read an amount of data in blocking mode from a specific memory address | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param DevAddress: Target device address | |
* @param MemAddress: Internal memory address | |
* @param MemAddSize: Size of internal memory address | |
* @param pData: Pointer to data buffer | |
* @param Size: Amount of data to be sent | |
* @param Timeout: Timeout duration | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_I2C_Mem_Read(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress, uint16_t MemAddSize, uint8_t *pData, uint16_t Size, uint32_t Timeout) | |
{ | |
uint32_t tickstart = 0; | |
/* Check the parameters */ | |
assert_param(IS_I2C_MEMADD_SIZE(MemAddSize)); | |
if(hi2c->State == HAL_I2C_STATE_READY) | |
{ | |
if((pData == NULL) || (Size == 0)) | |
{ | |
return HAL_ERROR; | |
} | |
/* Process Locked */ | |
__HAL_LOCK(hi2c); | |
/* Init tickstart for timeout management*/ | |
tickstart = HAL_GetTick(); | |
if(I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_BUSY, SET, I2C_TIMEOUT_BUSY, tickstart) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
hi2c->State = HAL_I2C_STATE_BUSY_RX; | |
hi2c->Mode = HAL_I2C_MODE_MEM; | |
hi2c->ErrorCode = HAL_I2C_ERROR_NONE; | |
/* Prepare transfer parameters */ | |
hi2c->pBuffPtr = pData; | |
hi2c->XferCount = Size; | |
hi2c->XferISR = NULL; | |
/* Send Slave Address and Memory Address */ | |
if(I2C_RequestMemoryRead(hi2c, DevAddress, MemAddress, MemAddSize, Timeout, tickstart) != HAL_OK) | |
{ | |
if(hi2c->ErrorCode == HAL_I2C_ERROR_AF) | |
{ | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_ERROR; | |
} | |
else | |
{ | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_TIMEOUT; | |
} | |
} | |
/* Send Slave Address */ | |
/* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE and generate RESTART */ | |
if(hi2c->XferCount > MAX_NBYTE_SIZE) | |
{ | |
hi2c->XferSize = MAX_NBYTE_SIZE; | |
I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_RELOAD_MODE, I2C_GENERATE_START_READ); | |
} | |
else | |
{ | |
hi2c->XferSize = hi2c->XferCount; | |
I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_AUTOEND_MODE, I2C_GENERATE_START_READ); | |
} | |
do | |
{ | |
/* Wait until RXNE flag is set */ | |
if(I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_RXNE, RESET, Timeout, tickstart) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
/* Read data from RXDR */ | |
(*hi2c->pBuffPtr++) = hi2c->Instance->RXDR; | |
hi2c->XferSize--; | |
hi2c->XferCount--; | |
if((hi2c->XferSize == 0) && (hi2c->XferCount != 0)) | |
{ | |
/* Wait until TCR flag is set */ | |
if(I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_TCR, RESET, Timeout, tickstart) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
if(hi2c->XferCount > MAX_NBYTE_SIZE) | |
{ | |
hi2c->XferSize = MAX_NBYTE_SIZE; | |
I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_RELOAD_MODE, I2C_NO_STARTSTOP); | |
} | |
else | |
{ | |
hi2c->XferSize = hi2c->XferCount; | |
I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_AUTOEND_MODE, I2C_NO_STARTSTOP); | |
} | |
} | |
}while(hi2c->XferCount > 0); | |
/* No need to Check TC flag, with AUTOEND mode the stop is automatically generated */ | |
/* Wait until STOPF flag is reset */ | |
if(I2C_WaitOnSTOPFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK) | |
{ | |
if(hi2c->ErrorCode == HAL_I2C_ERROR_AF) | |
{ | |
return HAL_ERROR; | |
} | |
else | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
/* Clear STOP Flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF); | |
/* Clear Configuration Register 2 */ | |
I2C_RESET_CR2(hi2c); | |
hi2c->State = HAL_I2C_STATE_READY; | |
hi2c->Mode = HAL_I2C_MODE_NONE; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Write an amount of data in non-blocking mode with Interrupt to a specific memory address | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param DevAddress: Target device address | |
* @param MemAddress: Internal memory address | |
* @param MemAddSize: Size of internal memory address | |
* @param pData: Pointer to data buffer | |
* @param Size: Amount of data to be sent | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_I2C_Mem_Write_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress, uint16_t MemAddSize, uint8_t *pData, uint16_t Size) | |
{ | |
uint32_t tickstart = 0; | |
uint32_t xfermode = 0; | |
/* Check the parameters */ | |
assert_param(IS_I2C_MEMADD_SIZE(MemAddSize)); | |
if(hi2c->State == HAL_I2C_STATE_READY) | |
{ | |
if((pData == NULL) || (Size == 0)) | |
{ | |
return HAL_ERROR; | |
} | |
if(__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_BUSY) == SET) | |
{ | |
return HAL_BUSY; | |
} | |
/* Process Locked */ | |
__HAL_LOCK(hi2c); | |
/* Init tickstart for timeout management*/ | |
tickstart = HAL_GetTick(); | |
hi2c->State = HAL_I2C_STATE_BUSY_TX; | |
hi2c->Mode = HAL_I2C_MODE_MEM; | |
hi2c->ErrorCode = HAL_I2C_ERROR_NONE; | |
/* Prepare transfer parameters */ | |
hi2c->pBuffPtr = pData; | |
hi2c->XferCount = Size; | |
hi2c->XferOptions = I2C_NO_OPTION_FRAME; | |
hi2c->XferISR = I2C_Master_ISR_IT; | |
if(hi2c->XferCount > MAX_NBYTE_SIZE) | |
{ | |
hi2c->XferSize = MAX_NBYTE_SIZE; | |
xfermode = I2C_RELOAD_MODE; | |
} | |
else | |
{ | |
hi2c->XferSize = hi2c->XferCount; | |
xfermode = I2C_AUTOEND_MODE; | |
} | |
/* Send Slave Address and Memory Address */ | |
if(I2C_RequestMemoryWrite(hi2c, DevAddress, MemAddress, MemAddSize, I2C_TIMEOUT_FLAG, tickstart) != HAL_OK) | |
{ | |
if(hi2c->ErrorCode == HAL_I2C_ERROR_AF) | |
{ | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_ERROR; | |
} | |
else | |
{ | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_TIMEOUT; | |
} | |
} | |
/* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE and generate RESTART */ | |
I2C_TransferConfig(hi2c,DevAddress, hi2c->XferSize, xfermode, I2C_NO_STARTSTOP); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Note : The I2C interrupts must be enabled after unlocking current process | |
to avoid the risk of I2C interrupt handle execution before current | |
process unlock */ | |
/* Enable ERR, TC, STOP, NACK, TXI interrupt */ | |
/* possible to enable all of these */ | |
/* I2C_IT_ERRI | I2C_IT_TCI| I2C_IT_STOPI| I2C_IT_NACKI | I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */ | |
I2C_Enable_IRQ(hi2c, I2C_XFER_TX_IT); | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Read an amount of data in non-blocking mode with Interrupt from a specific memory address | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param DevAddress: Target device address | |
* @param MemAddress: Internal memory address | |
* @param MemAddSize: Size of internal memory address | |
* @param pData: Pointer to data buffer | |
* @param Size: Amount of data to be sent | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_I2C_Mem_Read_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress, uint16_t MemAddSize, uint8_t *pData, uint16_t Size) | |
{ | |
uint32_t tickstart = 0; | |
uint32_t xfermode = 0; | |
/* Check the parameters */ | |
assert_param(IS_I2C_MEMADD_SIZE(MemAddSize)); | |
if(hi2c->State == HAL_I2C_STATE_READY) | |
{ | |
if((pData == NULL) || (Size == 0)) | |
{ | |
return HAL_ERROR; | |
} | |
if(__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_BUSY) == SET) | |
{ | |
return HAL_BUSY; | |
} | |
/* Process Locked */ | |
__HAL_LOCK(hi2c); | |
/* Init tickstart for timeout management*/ | |
tickstart = HAL_GetTick(); | |
hi2c->State = HAL_I2C_STATE_BUSY_RX; | |
hi2c->Mode = HAL_I2C_MODE_MEM; | |
hi2c->ErrorCode = HAL_I2C_ERROR_NONE; | |
/* Prepare transfer parameters */ | |
hi2c->pBuffPtr = pData; | |
hi2c->XferCount = Size; | |
hi2c->XferOptions = I2C_NO_OPTION_FRAME; | |
hi2c->XferISR = I2C_Master_ISR_IT; | |
if(hi2c->XferCount > MAX_NBYTE_SIZE) | |
{ | |
hi2c->XferSize = MAX_NBYTE_SIZE; | |
xfermode = I2C_RELOAD_MODE; | |
} | |
else | |
{ | |
hi2c->XferSize = hi2c->XferCount; | |
xfermode = I2C_AUTOEND_MODE; | |
} | |
/* Send Slave Address and Memory Address */ | |
if(I2C_RequestMemoryRead(hi2c, DevAddress, MemAddress, MemAddSize, I2C_TIMEOUT_FLAG, tickstart) != HAL_OK) | |
{ | |
if(hi2c->ErrorCode == HAL_I2C_ERROR_AF) | |
{ | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_ERROR; | |
} | |
else | |
{ | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_TIMEOUT; | |
} | |
} | |
/* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE and generate RESTART */ | |
I2C_TransferConfig(hi2c,DevAddress,hi2c->XferSize, xfermode, I2C_GENERATE_START_READ); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Note : The I2C interrupts must be enabled after unlocking current process | |
to avoid the risk of I2C interrupt handle execution before current | |
process unlock */ | |
/* Enable ERR, TC, STOP, NACK, RXI interrupt */ | |
/* possible to enable all of these */ | |
/* I2C_IT_ERRI | I2C_IT_TCI| I2C_IT_STOPI| I2C_IT_NACKI | I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */ | |
I2C_Enable_IRQ(hi2c, I2C_XFER_RX_IT); | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Write an amount of data in non-blocking mode with DMA to a specific memory address | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param DevAddress: Target device address | |
* @param MemAddress: Internal memory address | |
* @param MemAddSize: Size of internal memory address | |
* @param pData: Pointer to data buffer | |
* @param Size: Amount of data to be sent | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_I2C_Mem_Write_DMA(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress, uint16_t MemAddSize, uint8_t *pData, uint16_t Size) | |
{ | |
uint32_t tickstart = 0; | |
uint32_t xfermode = 0; | |
/* Check the parameters */ | |
assert_param(IS_I2C_MEMADD_SIZE(MemAddSize)); | |
if(hi2c->State == HAL_I2C_STATE_READY) | |
{ | |
if((pData == NULL) || (Size == 0)) | |
{ | |
return HAL_ERROR; | |
} | |
if(__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_BUSY) == SET) | |
{ | |
return HAL_BUSY; | |
} | |
/* Process Locked */ | |
__HAL_LOCK(hi2c); | |
/* Init tickstart for timeout management*/ | |
tickstart = HAL_GetTick(); | |
hi2c->State = HAL_I2C_STATE_BUSY_TX; | |
hi2c->Mode = HAL_I2C_MODE_MEM; | |
hi2c->ErrorCode = HAL_I2C_ERROR_NONE; | |
/* Prepare transfer parameters */ | |
hi2c->pBuffPtr = pData; | |
hi2c->XferCount = Size; | |
hi2c->XferOptions = I2C_NO_OPTION_FRAME; | |
hi2c->XferISR = I2C_Master_ISR_DMA; | |
if(hi2c->XferCount > MAX_NBYTE_SIZE) | |
{ | |
hi2c->XferSize = MAX_NBYTE_SIZE; | |
xfermode = I2C_RELOAD_MODE; | |
} | |
else | |
{ | |
hi2c->XferSize = hi2c->XferCount; | |
xfermode = I2C_AUTOEND_MODE; | |
} | |
/* Send Slave Address and Memory Address */ | |
if(I2C_RequestMemoryWrite(hi2c, DevAddress, MemAddress, MemAddSize, I2C_TIMEOUT_FLAG, tickstart) != HAL_OK) | |
{ | |
if(hi2c->ErrorCode == HAL_I2C_ERROR_AF) | |
{ | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_ERROR; | |
} | |
else | |
{ | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_TIMEOUT; | |
} | |
} | |
/* Set the I2C DMA transfer complete callback */ | |
hi2c->hdmatx->XferCpltCallback = I2C_DMAMasterTransmitCplt; | |
/* Set the DMA error callback */ | |
hi2c->hdmatx->XferErrorCallback = I2C_DMAError; | |
/* Set the unused DMA callbacks to NULL */ | |
hi2c->hdmatx->XferHalfCpltCallback = NULL; | |
hi2c->hdmatx->XferAbortCallback = NULL; | |
/* Enable the DMA channel */ | |
HAL_DMA_Start_IT(hi2c->hdmatx, (uint32_t)pData, (uint32_t)&hi2c->Instance->TXDR, hi2c->XferSize); | |
/* Send Slave Address */ | |
/* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE and generate RESTART */ | |
I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, xfermode, I2C_NO_STARTSTOP); | |
/* Update XferCount value */ | |
hi2c->XferCount -= hi2c->XferSize; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Note : The I2C interrupts must be enabled after unlocking current process | |
to avoid the risk of I2C interrupt handle execution before current | |
process unlock */ | |
/* Enable ERR and NACK interrupts */ | |
I2C_Enable_IRQ(hi2c, I2C_XFER_ERROR_IT); | |
/* Enable DMA Request */ | |
hi2c->Instance->CR1 |= I2C_CR1_TXDMAEN; | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Reads an amount of data in non-blocking mode with DMA from a specific memory address. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param DevAddress: Target device address | |
* @param MemAddress: Internal memory address | |
* @param MemAddSize: Size of internal memory address | |
* @param pData: Pointer to data buffer | |
* @param Size: Amount of data to be read | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_I2C_Mem_Read_DMA(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress, uint16_t MemAddSize, uint8_t *pData, uint16_t Size) | |
{ | |
uint32_t tickstart = 0; | |
uint32_t xfermode = 0; | |
/* Check the parameters */ | |
assert_param(IS_I2C_MEMADD_SIZE(MemAddSize)); | |
if(hi2c->State == HAL_I2C_STATE_READY) | |
{ | |
if((pData == NULL) || (Size == 0)) | |
{ | |
return HAL_ERROR; | |
} | |
if(__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_BUSY) == SET) | |
{ | |
return HAL_BUSY; | |
} | |
/* Process Locked */ | |
__HAL_LOCK(hi2c); | |
/* Init tickstart for timeout management*/ | |
tickstart = HAL_GetTick(); | |
hi2c->State = HAL_I2C_STATE_BUSY_RX; | |
hi2c->Mode = HAL_I2C_MODE_MEM; | |
hi2c->ErrorCode = HAL_I2C_ERROR_NONE; | |
/* Prepare transfer parameters */ | |
hi2c->pBuffPtr = pData; | |
hi2c->XferCount = Size; | |
hi2c->XferOptions = I2C_NO_OPTION_FRAME; | |
hi2c->XferISR = I2C_Master_ISR_DMA; | |
if(hi2c->XferCount > MAX_NBYTE_SIZE) | |
{ | |
hi2c->XferSize = MAX_NBYTE_SIZE; | |
xfermode = I2C_RELOAD_MODE; | |
} | |
else | |
{ | |
hi2c->XferSize = hi2c->XferCount; | |
xfermode = I2C_AUTOEND_MODE; | |
} | |
/* Send Slave Address and Memory Address */ | |
if(I2C_RequestMemoryRead(hi2c, DevAddress, MemAddress, MemAddSize, I2C_TIMEOUT_FLAG, tickstart) != HAL_OK) | |
{ | |
if(hi2c->ErrorCode == HAL_I2C_ERROR_AF) | |
{ | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_ERROR; | |
} | |
else | |
{ | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_TIMEOUT; | |
} | |
} | |
/* Set the I2C DMA transfer complete callback */ | |
hi2c->hdmarx->XferCpltCallback = I2C_DMAMasterReceiveCplt; | |
/* Set the DMA error callback */ | |
hi2c->hdmarx->XferErrorCallback = I2C_DMAError; | |
/* Set the unused DMA callbacks to NULL */ | |
hi2c->hdmarx->XferHalfCpltCallback = NULL; | |
hi2c->hdmarx->XferAbortCallback = NULL; | |
/* Enable the DMA channel */ | |
HAL_DMA_Start_IT(hi2c->hdmarx, (uint32_t)&hi2c->Instance->RXDR, (uint32_t)pData, hi2c->XferSize); | |
/* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE and generate RESTART */ | |
I2C_TransferConfig(hi2c,DevAddress, hi2c->XferSize, xfermode, I2C_GENERATE_START_READ); | |
/* Update XferCount value */ | |
hi2c->XferCount -= hi2c->XferSize; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Enable DMA Request */ | |
hi2c->Instance->CR1 |= I2C_CR1_RXDMAEN; | |
/* Note : The I2C interrupts must be enabled after unlocking current process | |
to avoid the risk of I2C interrupt handle execution before current | |
process unlock */ | |
/* Enable ERR and NACK interrupts */ | |
I2C_Enable_IRQ(hi2c, I2C_XFER_ERROR_IT); | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Checks if target device is ready for communication. | |
* @note This function is used with Memory devices | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param DevAddress: Target device address | |
* @param Trials: Number of trials | |
* @param Timeout: Timeout duration | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_I2C_IsDeviceReady(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint32_t Trials, uint32_t Timeout) | |
{ | |
uint32_t tickstart = 0; | |
__IO uint32_t I2C_Trials = 0; | |
if(hi2c->State == HAL_I2C_STATE_READY) | |
{ | |
if(__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_BUSY) == SET) | |
{ | |
return HAL_BUSY; | |
} | |
/* Process Locked */ | |
__HAL_LOCK(hi2c); | |
hi2c->State = HAL_I2C_STATE_BUSY; | |
hi2c->ErrorCode = HAL_I2C_ERROR_NONE; | |
do | |
{ | |
/* Generate Start */ | |
hi2c->Instance->CR2 = I2C_GENERATE_START(hi2c->Init.AddressingMode,DevAddress); | |
/* No need to Check TC flag, with AUTOEND mode the stop is automatically generated */ | |
/* Wait until STOPF flag is set or a NACK flag is set*/ | |
tickstart = HAL_GetTick(); | |
while((__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_STOPF) == RESET) && (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_AF) == RESET) && (hi2c->State != HAL_I2C_STATE_TIMEOUT)) | |
{ | |
if(Timeout != HAL_MAX_DELAY) | |
{ | |
if((Timeout == 0)||((HAL_GetTick() - tickstart ) > Timeout)) | |
{ | |
/* Device is ready */ | |
hi2c->State = HAL_I2C_STATE_READY; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
/* Check if the NACKF flag has not been set */ | |
if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_AF) == RESET) | |
{ | |
/* Wait until STOPF flag is reset */ | |
if(I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_STOPF, RESET, Timeout, tickstart) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
/* Clear STOP Flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF); | |
/* Device is ready */ | |
hi2c->State = HAL_I2C_STATE_READY; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_OK; | |
} | |
else | |
{ | |
/* Wait until STOPF flag is reset */ | |
if(I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_STOPF, RESET, Timeout, tickstart) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
/* Clear NACK Flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); | |
/* Clear STOP Flag, auto generated with autoend*/ | |
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF); | |
} | |
/* Check if the maximum allowed number of trials has been reached */ | |
if (I2C_Trials++ == Trials) | |
{ | |
/* Generate Stop */ | |
hi2c->Instance->CR2 |= I2C_CR2_STOP; | |
/* Wait until STOPF flag is reset */ | |
if(I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_STOPF, RESET, Timeout, tickstart) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
/* Clear STOP Flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF); | |
} | |
}while(I2C_Trials < Trials); | |
hi2c->State = HAL_I2C_STATE_READY; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_TIMEOUT; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Sequential transmit in master I2C mode an amount of data in non-blocking mode with Interrupt. | |
* @note This interface allow to manage repeated start condition when a direction change during transfer | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param DevAddress: Target device address | |
* @param pData: Pointer to data buffer | |
* @param Size: Amount of data to be sent | |
* @param XferOptions: Options of Transfer, value of @ref I2C_XFEROPTIONS | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_I2C_Master_Sequential_Transmit_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, uint16_t Size, uint32_t XferOptions) | |
{ | |
uint32_t xfermode = 0; | |
uint32_t xferrequest = I2C_GENERATE_START_WRITE; | |
/* Check the parameters */ | |
assert_param(IS_I2C_TRANSFER_OPTIONS_REQUEST(XferOptions)); | |
if(hi2c->State == HAL_I2C_STATE_READY) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hi2c); | |
hi2c->State = HAL_I2C_STATE_BUSY_TX; | |
hi2c->Mode = HAL_I2C_MODE_MASTER; | |
hi2c->ErrorCode = HAL_I2C_ERROR_NONE; | |
/* Prepare transfer parameters */ | |
hi2c->pBuffPtr = pData; | |
hi2c->XferCount = Size; | |
hi2c->XferOptions = XferOptions; | |
hi2c->XferISR = I2C_Master_ISR_IT; | |
/* If size > MAX_NBYTE_SIZE, use reload mode */ | |
if(hi2c->XferCount > MAX_NBYTE_SIZE) | |
{ | |
hi2c->XferSize = MAX_NBYTE_SIZE; | |
xfermode = I2C_RELOAD_MODE; | |
} | |
else | |
{ | |
hi2c->XferSize = hi2c->XferCount; | |
xfermode = hi2c->XferOptions; | |
/* If transfer direction not change, do not generate Restart Condition */ | |
/* Mean Previous state is same as current state */ | |
if(hi2c->PreviousState == I2C_STATE_SLAVE_BUSY_TX) | |
{ | |
xferrequest = I2C_NO_STARTSTOP; | |
} | |
} | |
/* Send Slave Address and set NBYTES to write */ | |
I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, xfermode, xferrequest); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Note : The I2C interrupts must be enabled after unlocking current process | |
to avoid the risk of I2C interrupt handle execution before current | |
process unlock */ | |
I2C_Enable_IRQ(hi2c, I2C_XFER_TX_IT); | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Sequential receive in master I2C mode an amount of data in non-blocking mode with Interrupt | |
* @note This interface allow to manage repeated start condition when a direction change during transfer | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param DevAddress: Target device address | |
* @param pData: Pointer to data buffer | |
* @param Size: Amount of data to be sent | |
* @param XferOptions: Options of Transfer, value of @ref I2C_XFEROPTIONS | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_I2C_Master_Sequential_Receive_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, uint16_t Size, uint32_t XferOptions) | |
{ | |
uint32_t xfermode = 0; | |
uint32_t xferrequest = I2C_GENERATE_START_READ; | |
/* Check the parameters */ | |
assert_param(IS_I2C_TRANSFER_OPTIONS_REQUEST(XferOptions)); | |
if(hi2c->State == HAL_I2C_STATE_READY) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hi2c); | |
hi2c->State = HAL_I2C_STATE_BUSY_RX; | |
hi2c->Mode = HAL_I2C_MODE_MASTER; | |
hi2c->ErrorCode = HAL_I2C_ERROR_NONE; | |
/* Prepare transfer parameters */ | |
hi2c->pBuffPtr = pData; | |
hi2c->XferCount = Size; | |
hi2c->XferOptions = XferOptions; | |
hi2c->XferISR = I2C_Master_ISR_IT; | |
/* If hi2c->XferCount > MAX_NBYTE_SIZE, use reload mode */ | |
if(hi2c->XferCount > MAX_NBYTE_SIZE) | |
{ | |
hi2c->XferSize = MAX_NBYTE_SIZE; | |
xfermode = I2C_RELOAD_MODE; | |
} | |
else | |
{ | |
hi2c->XferSize = hi2c->XferCount; | |
xfermode = hi2c->XferOptions; | |
/* If transfer direction not change, do not generate Restart Condition */ | |
/* Mean Previous state is same as current state */ | |
if(hi2c->PreviousState == I2C_STATE_MASTER_BUSY_RX) | |
{ | |
xferrequest = I2C_NO_STARTSTOP; | |
} | |
} | |
/* Send Slave Address and set NBYTES to read */ | |
I2C_TransferConfig(hi2c,DevAddress, hi2c->XferSize, xfermode, xferrequest); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Note : The I2C interrupts must be enabled after unlocking current process | |
to avoid the risk of I2C interrupt handle execution before current | |
process unlock */ | |
I2C_Enable_IRQ(hi2c, I2C_XFER_RX_IT); | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Sequential transmit in slave/device I2C mode an amount of data in non-blocking mode with Interrupt | |
* @note This interface allow to manage repeated start condition when a direction change during transfer | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param pData: Pointer to data buffer | |
* @param Size: Amount of data to be sent | |
* @param XferOptions: Options of Transfer, value of @ref I2C_XFEROPTIONS | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_I2C_Slave_Sequential_Transmit_IT(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size, uint32_t XferOptions) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_I2C_TRANSFER_OPTIONS_REQUEST(XferOptions)); | |
if(hi2c->State == HAL_I2C_STATE_LISTEN) | |
{ | |
if((pData == NULL) || (Size == 0)) | |
{ | |
return HAL_ERROR; | |
} | |
/* Disable Interrupts, to prevent preemption during treatment in case of multicall */ | |
I2C_Disable_IRQ(hi2c, I2C_XFER_LISTEN_IT | I2C_XFER_TX_IT); | |
/* Process Locked */ | |
__HAL_LOCK(hi2c); | |
hi2c->State = HAL_I2C_STATE_BUSY_TX_LISTEN; | |
hi2c->Mode = HAL_I2C_MODE_SLAVE; | |
hi2c->ErrorCode = HAL_I2C_ERROR_NONE; | |
/* Enable Address Acknowledge */ | |
hi2c->Instance->CR2 &= ~I2C_CR2_NACK; | |
/* Prepare transfer parameters */ | |
hi2c->pBuffPtr = pData; | |
hi2c->XferCount = Size; | |
hi2c->XferSize = hi2c->XferCount; | |
hi2c->XferOptions = XferOptions; | |
hi2c->XferISR = I2C_Slave_ISR_IT; | |
if(I2C_GET_DIR(hi2c) == I2C_DIRECTION_RECEIVE) | |
{ | |
/* Clear ADDR flag after prepare the transfer parameters */ | |
/* This action will generate an acknowledge to the Master */ | |
__HAL_I2C_CLEAR_FLAG(hi2c,I2C_FLAG_ADDR); | |
} | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Note : The I2C interrupts must be enabled after unlocking current process | |
to avoid the risk of I2C interrupt handle execution before current | |
process unlock */ | |
/* REnable ADDR interrupt */ | |
I2C_Enable_IRQ(hi2c, I2C_XFER_TX_IT | I2C_XFER_LISTEN_IT); | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/** | |
* @brief Sequential receive in slave/device I2C mode an amount of data in non-blocking mode with Interrupt | |
* @note This interface allow to manage repeated start condition when a direction change during transfer | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param pData: Pointer to data buffer | |
* @param Size: Amount of data to be sent | |
* @param XferOptions: Options of Transfer, value of @ref I2C_XFEROPTIONS | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_I2C_Slave_Sequential_Receive_IT(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size, uint32_t XferOptions) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_I2C_TRANSFER_OPTIONS_REQUEST(XferOptions)); | |
if(hi2c->State == HAL_I2C_STATE_LISTEN) | |
{ | |
if((pData == NULL) || (Size == 0)) | |
{ | |
return HAL_ERROR; | |
} | |
/* Disable Interrupts, to prevent preemption during treatment in case of multicall */ | |
I2C_Disable_IRQ(hi2c, I2C_XFER_LISTEN_IT | I2C_XFER_RX_IT); | |
/* Process Locked */ | |
__HAL_LOCK(hi2c); | |
hi2c->State = HAL_I2C_STATE_BUSY_RX_LISTEN; | |
hi2c->Mode = HAL_I2C_MODE_SLAVE; | |
hi2c->ErrorCode = HAL_I2C_ERROR_NONE; | |
/* Enable Address Acknowledge */ | |
hi2c->Instance->CR2 &= ~I2C_CR2_NACK; | |
/* Prepare transfer parameters */ | |
hi2c->pBuffPtr = pData; | |
hi2c->XferCount = Size; | |
hi2c->XferSize = hi2c->XferCount; | |
hi2c->XferOptions = XferOptions; | |
hi2c->XferISR = I2C_Slave_ISR_IT; | |
if(I2C_GET_DIR(hi2c) == I2C_DIRECTION_TRANSMIT) | |
{ | |
/* Clear ADDR flag after prepare the transfer parameters */ | |
/* This action will generate an acknowledge to the Master */ | |
__HAL_I2C_CLEAR_FLAG(hi2c,I2C_FLAG_ADDR); | |
} | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Note : The I2C interrupts must be enabled after unlocking current process | |
to avoid the risk of I2C interrupt handle execution before current | |
process unlock */ | |
/* REnable ADDR interrupt */ | |
I2C_Enable_IRQ(hi2c, I2C_XFER_RX_IT | I2C_XFER_LISTEN_IT); | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/** | |
* @brief Enable the Address listen mode with Interrupt. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_I2C_EnableListen_IT(I2C_HandleTypeDef *hi2c) | |
{ | |
if(hi2c->State == HAL_I2C_STATE_READY) | |
{ | |
hi2c->State = HAL_I2C_STATE_LISTEN; | |
hi2c->XferISR = I2C_Slave_ISR_IT; | |
/* Enable the Address Match interrupt */ | |
I2C_Enable_IRQ(hi2c, I2C_XFER_LISTEN_IT); | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Disable the Address listen mode with Interrupt. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_I2C_DisableListen_IT(I2C_HandleTypeDef *hi2c) | |
{ | |
/* Declaration of tmp to prevent undefined behavior of volatile usage */ | |
uint32_t tmp; | |
/* Disable Address listen mode only if a transfer is not ongoing */ | |
if(hi2c->State == HAL_I2C_STATE_LISTEN) | |
{ | |
tmp = (uint32_t)(hi2c->State) & I2C_STATE_MSK; | |
hi2c->PreviousState = tmp | (uint32_t)(hi2c->Mode); | |
hi2c->State = HAL_I2C_STATE_READY; | |
hi2c->Mode = HAL_I2C_MODE_NONE; | |
hi2c->XferISR = NULL; | |
/* Disable the Address Match interrupt */ | |
I2C_Disable_IRQ(hi2c, I2C_XFER_LISTEN_IT); | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Abort a master I2C IT or DMA process communication with Interrupt. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param DevAddress: Target device address | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_I2C_Master_Abort_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress) | |
{ | |
if(hi2c->Mode == HAL_I2C_MODE_MASTER) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hi2c); | |
/* Disable Interrupts */ | |
I2C_Disable_IRQ(hi2c, I2C_XFER_RX_IT); | |
I2C_Disable_IRQ(hi2c, I2C_XFER_TX_IT); | |
/* Set State at HAL_I2C_STATE_ABORT */ | |
hi2c->State = HAL_I2C_STATE_ABORT; | |
/* Set NBYTES to 1 to generate a dummy read on I2C peripheral */ | |
/* Set AUTOEND mode, this will generate a NACK then STOP condition to abort the current transfer */ | |
I2C_TransferConfig(hi2c, 0, 1, I2C_AUTOEND_MODE, I2C_GENERATE_STOP); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Note : The I2C interrupts must be enabled after unlocking current process | |
to avoid the risk of I2C interrupt handle execution before current | |
process unlock */ | |
I2C_Enable_IRQ(hi2c, I2C_XFER_CPLT_IT); | |
return HAL_OK; | |
} | |
else | |
{ | |
/* Wrong usage of abort function */ | |
/* This function should be used only in case of abort monitored by master device */ | |
return HAL_ERROR; | |
} | |
} | |
/** | |
* @} | |
*/ | |
/** @defgroup I2C_IRQ_Handler_and_Callbacks IRQ Handler and Callbacks | |
* @{ | |
*/ | |
/** | |
* @brief This function handles I2C event interrupt request. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @retval None | |
*/ | |
void HAL_I2C_EV_IRQHandler(I2C_HandleTypeDef *hi2c) | |
{ | |
/* Get current IT Flags and IT sources value */ | |
uint32_t itflags = READ_REG(hi2c->Instance->ISR); | |
uint32_t itsources = READ_REG(hi2c->Instance->CR1); | |
/* I2C events treatment -------------------------------------*/ | |
if(hi2c->XferISR != NULL) | |
{ | |
hi2c->XferISR(hi2c, itflags, itsources); | |
} | |
} | |
/** | |
* @brief This function handles I2C error interrupt request. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @retval None | |
*/ | |
void HAL_I2C_ER_IRQHandler(I2C_HandleTypeDef *hi2c) | |
{ | |
uint32_t itflags = READ_REG(hi2c->Instance->ISR); | |
uint32_t itsources = READ_REG(hi2c->Instance->CR1); | |
/* I2C Bus error interrupt occurred ------------------------------------*/ | |
if(((itflags & I2C_FLAG_BERR) != RESET) && ((itsources & I2C_IT_ERRI) != RESET)) | |
{ | |
hi2c->ErrorCode |= HAL_I2C_ERROR_BERR; | |
/* Clear BERR flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_BERR); | |
} | |
/* I2C Over-Run/Under-Run interrupt occurred ----------------------------------------*/ | |
if(((itflags & I2C_FLAG_OVR) != RESET) && ((itsources & I2C_IT_ERRI) != RESET)) | |
{ | |
hi2c->ErrorCode |= HAL_I2C_ERROR_OVR; | |
/* Clear OVR flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_OVR); | |
} | |
/* I2C Arbitration Loss error interrupt occurred -------------------------------------*/ | |
if(((itflags & I2C_FLAG_ARLO) != RESET) && ((itsources & I2C_IT_ERRI) != RESET)) | |
{ | |
hi2c->ErrorCode |= HAL_I2C_ERROR_ARLO; | |
/* Clear ARLO flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_ARLO); | |
} | |
/* Call the Error Callback in case of Error detected */ | |
if((hi2c->ErrorCode & (HAL_I2C_ERROR_BERR | HAL_I2C_ERROR_OVR | HAL_I2C_ERROR_ARLO)) != HAL_I2C_ERROR_NONE) | |
{ | |
I2C_ITError(hi2c, hi2c->ErrorCode); | |
} | |
} | |
/** | |
* @brief Master Tx Transfer completed callback. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @retval None | |
*/ | |
__weak void HAL_I2C_MasterTxCpltCallback(I2C_HandleTypeDef *hi2c) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(hi2c); | |
/* NOTE : This function should not be modified, when the callback is needed, | |
the HAL_I2C_MasterTxCpltCallback could be implemented in the user file | |
*/ | |
} | |
/** | |
* @brief Master Rx Transfer completed callback. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @retval None | |
*/ | |
__weak void HAL_I2C_MasterRxCpltCallback(I2C_HandleTypeDef *hi2c) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(hi2c); | |
/* NOTE : This function should not be modified, when the callback is needed, | |
the HAL_I2C_MasterRxCpltCallback could be implemented in the user file | |
*/ | |
} | |
/** @brief Slave Tx Transfer completed callback. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @retval None | |
*/ | |
__weak void HAL_I2C_SlaveTxCpltCallback(I2C_HandleTypeDef *hi2c) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(hi2c); | |
/* NOTE : This function should not be modified, when the callback is needed, | |
the HAL_I2C_SlaveTxCpltCallback could be implemented in the user file | |
*/ | |
} | |
/** | |
* @brief Slave Rx Transfer completed callback. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @retval None | |
*/ | |
__weak void HAL_I2C_SlaveRxCpltCallback(I2C_HandleTypeDef *hi2c) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(hi2c); | |
/* NOTE : This function should not be modified, when the callback is needed, | |
the HAL_I2C_SlaveRxCpltCallback could be implemented in the user file | |
*/ | |
} | |
/** | |
* @brief Slave Address Match callback. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param TransferDirection: Master request Transfer Direction (Write/Read), value of @ref I2C_XFEROPTIONS | |
* @param AddrMatchCode: Address Match Code | |
* @retval None | |
*/ | |
__weak void HAL_I2C_AddrCallback(I2C_HandleTypeDef *hi2c, uint8_t TransferDirection, uint16_t AddrMatchCode) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(hi2c); | |
UNUSED(TransferDirection); | |
UNUSED(AddrMatchCode); | |
/* NOTE : This function should not be modified, when the callback is needed, | |
the HAL_I2C_AddrCallback() could be implemented in the user file | |
*/ | |
} | |
/** | |
* @brief Listen Complete callback. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @retval None | |
*/ | |
__weak void HAL_I2C_ListenCpltCallback(I2C_HandleTypeDef *hi2c) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(hi2c); | |
/* NOTE : This function should not be modified, when the callback is needed, | |
the HAL_I2C_ListenCpltCallback() could be implemented in the user file | |
*/ | |
} | |
/** | |
* @brief Memory Tx Transfer completed callback. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @retval None | |
*/ | |
__weak void HAL_I2C_MemTxCpltCallback(I2C_HandleTypeDef *hi2c) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(hi2c); | |
/* NOTE : This function should not be modified, when the callback is needed, | |
the HAL_I2C_MemTxCpltCallback could be implemented in the user file | |
*/ | |
} | |
/** | |
* @brief Memory Rx Transfer completed callback. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @retval None | |
*/ | |
__weak void HAL_I2C_MemRxCpltCallback(I2C_HandleTypeDef *hi2c) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(hi2c); | |
/* NOTE : This function should not be modified, when the callback is needed, | |
the HAL_I2C_MemRxCpltCallback could be implemented in the user file | |
*/ | |
} | |
/** | |
* @brief I2C error callback. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @retval None | |
*/ | |
__weak void HAL_I2C_ErrorCallback(I2C_HandleTypeDef *hi2c) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(hi2c); | |
/* NOTE : This function should not be modified, when the callback is needed, | |
the HAL_I2C_ErrorCallback could be implemented in the user file | |
*/ | |
} | |
/** | |
* @brief I2C abort callback. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @retval None | |
*/ | |
__weak void HAL_I2C_AbortCpltCallback(I2C_HandleTypeDef *hi2c) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(hi2c); | |
/* NOTE : This function should not be modified, when the callback is needed, | |
the HAL_I2C_AbortCpltCallback could be implemented in the user file | |
*/ | |
} | |
/** | |
* @} | |
*/ | |
/** @defgroup I2C_Exported_Functions_Group3 Peripheral State, Mode and Error functions | |
* @brief Peripheral State, Mode and Error functions | |
* | |
@verbatim | |
=============================================================================== | |
##### Peripheral State, Mode and Error functions ##### | |
=============================================================================== | |
[..] | |
This subsection permit to get in run-time the status of the peripheral | |
and the data flow. | |
@endverbatim | |
* @{ | |
*/ | |
/** | |
* @brief Return the I2C handle state. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @retval HAL state | |
*/ | |
HAL_I2C_StateTypeDef HAL_I2C_GetState(I2C_HandleTypeDef *hi2c) | |
{ | |
/* Return I2C handle state */ | |
return hi2c->State; | |
} | |
/** | |
* @brief Returns the I2C Master, Slave, Memory or no mode. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for I2C module | |
* @retval HAL mode | |
*/ | |
HAL_I2C_ModeTypeDef HAL_I2C_GetMode(I2C_HandleTypeDef *hi2c) | |
{ | |
return hi2c->Mode; | |
} | |
/** | |
* @brief Return the I2C error code. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @retval I2C Error Code | |
*/ | |
uint32_t HAL_I2C_GetError(I2C_HandleTypeDef *hi2c) | |
{ | |
return hi2c->ErrorCode; | |
} | |
/** | |
* @} | |
*/ | |
/** | |
* @} | |
*/ | |
/** @addtogroup I2C_Private_Functions | |
* @{ | |
*/ | |
/** | |
* @brief Interrupt Sub-Routine which handle the Interrupt Flags Master Mode with Interrupt. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param ITFlags: Interrupt flags to handle. | |
* @param ITSources: Interrupt sources enabled. | |
* @retval HAL status | |
*/ | |
static HAL_StatusTypeDef I2C_Master_ISR_IT(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, uint32_t ITSources) | |
{ | |
uint16_t devaddress = 0; | |
/* Process Locked */ | |
__HAL_LOCK(hi2c); | |
if(((ITFlags & I2C_FLAG_AF) != RESET) && ((ITSources & I2C_IT_NACKI) != RESET)) | |
{ | |
/* Clear NACK Flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); | |
/* Set corresponding Error Code */ | |
/* No need to generate STOP, it is automatically done */ | |
/* Error callback will be send during stop flag treatment */ | |
hi2c->ErrorCode |= HAL_I2C_ERROR_AF; | |
/* Flush TX register */ | |
I2C_Flush_TXDR(hi2c); | |
} | |
else if(((ITFlags & I2C_FLAG_RXNE) != RESET) && ((ITSources & I2C_IT_RXI) != RESET)) | |
{ | |
/* Read data from RXDR */ | |
(*hi2c->pBuffPtr++) = hi2c->Instance->RXDR; | |
hi2c->XferSize--; | |
hi2c->XferCount--; | |
} | |
else if(((ITFlags & I2C_FLAG_TXIS) != RESET) && ((ITSources & I2C_IT_TXI) != RESET)) | |
{ | |
/* Write data to TXDR */ | |
hi2c->Instance->TXDR = (*hi2c->pBuffPtr++); | |
hi2c->XferSize--; | |
hi2c->XferCount--; | |
} | |
else if(((ITFlags & I2C_FLAG_TCR) != RESET) && ((ITSources & I2C_IT_TCI) != RESET)) | |
{ | |
if((hi2c->XferSize == 0) && (hi2c->XferCount != 0)) | |
{ | |
devaddress = (hi2c->Instance->CR2 & I2C_CR2_SADD); | |
if(hi2c->XferCount > MAX_NBYTE_SIZE) | |
{ | |
hi2c->XferSize = MAX_NBYTE_SIZE; | |
I2C_TransferConfig(hi2c, devaddress, hi2c->XferSize, I2C_RELOAD_MODE, I2C_NO_STARTSTOP); | |
} | |
else | |
{ | |
hi2c->XferSize = hi2c->XferCount; | |
if(hi2c->XferOptions != I2C_NO_OPTION_FRAME) | |
{ | |
I2C_TransferConfig(hi2c, devaddress, hi2c->XferSize, hi2c->XferOptions, I2C_NO_STARTSTOP); | |
} | |
else | |
{ | |
I2C_TransferConfig(hi2c, devaddress, hi2c->XferSize, I2C_AUTOEND_MODE, I2C_NO_STARTSTOP); | |
} | |
} | |
} | |
else | |
{ | |
/* Call TxCpltCallback() if no stop mode is set */ | |
if((I2C_GET_STOP_MODE(hi2c) != I2C_AUTOEND_MODE)&&(hi2c->Mode == HAL_I2C_MODE_MASTER)) | |
{ | |
/* Call I2C Master Sequential complete process */ | |
I2C_ITMasterSequentialCplt(hi2c); | |
} | |
else | |
{ | |
/* Wrong size Status regarding TCR flag event */ | |
/* Call the corresponding callback to inform upper layer of End of Transfer */ | |
I2C_ITError(hi2c, HAL_I2C_ERROR_SIZE); | |
} | |
} | |
} | |
else if(((ITFlags & I2C_FLAG_TC) != RESET) && ((ITSources & I2C_IT_TCI) != RESET)) | |
{ | |
if(hi2c->XferCount == 0) | |
{ | |
if((I2C_GET_STOP_MODE(hi2c) != I2C_AUTOEND_MODE)&&(hi2c->Mode == HAL_I2C_MODE_MASTER)) | |
{ | |
/* Call I2C Master Sequential complete process */ | |
I2C_ITMasterSequentialCplt(hi2c); | |
} | |
} | |
else | |
{ | |
/* Wrong size Status regarding TC flag event */ | |
/* Call the corresponding callback to inform upper layer of End of Transfer */ | |
I2C_ITError(hi2c, HAL_I2C_ERROR_SIZE); | |
} | |
} | |
if(((ITFlags & I2C_FLAG_STOPF) != RESET) && ((ITSources & I2C_IT_STOPI) != RESET)) | |
{ | |
/* Call I2C Master complete process */ | |
I2C_ITMasterCplt(hi2c, ITFlags); | |
} | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_OK; | |
} | |
/** | |
* @brief Interrupt Sub-Routine which handle the Interrupt Flags Slave Mode with Interrupt. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param ITFlags: Interrupt flags to handle. | |
* @param ITSources: Interrupt sources enabled. | |
* @retval HAL status | |
*/ | |
static HAL_StatusTypeDef I2C_Slave_ISR_IT(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, uint32_t ITSources) | |
{ | |
/* Process locked */ | |
__HAL_LOCK(hi2c); | |
if(((ITFlags & I2C_FLAG_AF) != RESET) && ((ITSources & I2C_IT_NACKI) != RESET)) | |
{ | |
/* Check that I2C transfer finished */ | |
/* if yes, normal use case, a NACK is sent by the MASTER when Transfer is finished */ | |
/* Mean XferCount == 0*/ | |
/* So clear Flag NACKF only */ | |
if(hi2c->XferCount == 0) | |
{ | |
if(((hi2c->XferOptions == I2C_FIRST_AND_LAST_FRAME) || (hi2c->XferOptions == I2C_LAST_FRAME)) && \ | |
(hi2c->State == HAL_I2C_STATE_LISTEN)) | |
{ | |
/* Call I2C Listen complete process */ | |
I2C_ITListenCplt(hi2c, ITFlags); | |
} | |
else if((hi2c->XferOptions != I2C_NO_OPTION_FRAME) && (hi2c->State == HAL_I2C_STATE_BUSY_TX_LISTEN)) | |
{ | |
/* Clear NACK Flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); | |
/* Flush TX register */ | |
I2C_Flush_TXDR(hi2c); | |
/* Last Byte is Transmitted */ | |
/* Call I2C Slave Sequential complete process */ | |
I2C_ITSlaveSequentialCplt(hi2c); | |
} | |
else | |
{ | |
/* Clear NACK Flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); | |
} | |
} | |
else | |
{ | |
/* if no, error use case, a Non-Acknowledge of last Data is generated by the MASTER*/ | |
/* Clear NACK Flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); | |
/* Set ErrorCode corresponding to a Non-Acknowledge */ | |
hi2c->ErrorCode |= HAL_I2C_ERROR_AF; | |
} | |
} | |
else if(((ITFlags & I2C_FLAG_RXNE) != RESET) && ((ITSources & I2C_IT_RXI) != RESET)) | |
{ | |
if(hi2c->XferCount > 0) | |
{ | |
/* Read data from RXDR */ | |
(*hi2c->pBuffPtr++) = hi2c->Instance->RXDR; | |
hi2c->XferSize--; | |
hi2c->XferCount--; | |
} | |
if((hi2c->XferCount == 0) && \ | |
(hi2c->XferOptions != I2C_NO_OPTION_FRAME)) | |
{ | |
/* Call I2C Slave Sequential complete process */ | |
I2C_ITSlaveSequentialCplt(hi2c); | |
} | |
} | |
else if(((ITFlags & I2C_FLAG_ADDR) != RESET) && ((ITSources & I2C_IT_ADDRI) != RESET)) | |
{ | |
I2C_ITAddrCplt(hi2c, ITFlags); | |
} | |
else if(((ITFlags & I2C_FLAG_TXIS) != RESET) && ((ITSources & I2C_IT_TXI) != RESET)) | |
{ | |
/* Write data to TXDR only if XferCount not reach "0" */ | |
/* A TXIS flag can be set, during STOP treatment */ | |
/* Check if all Datas have already been sent */ | |
/* If it is the case, this last write in TXDR is not sent, correspond to a dummy TXIS event */ | |
if(hi2c->XferCount > 0) | |
{ | |
/* Write data to TXDR */ | |
hi2c->Instance->TXDR = (*hi2c->pBuffPtr++); | |
hi2c->XferCount--; | |
hi2c->XferSize--; | |
} | |
else | |
{ | |
if((hi2c->XferOptions == I2C_NEXT_FRAME) || (hi2c->XferOptions == I2C_FIRST_FRAME)) | |
{ | |
/* Last Byte is Transmitted */ | |
/* Call I2C Slave Sequential complete process */ | |
I2C_ITSlaveSequentialCplt(hi2c); | |
} | |
} | |
} | |
/* Check if STOPF is set */ | |
if(((ITFlags & I2C_FLAG_STOPF) != RESET) && ((ITSources & I2C_IT_STOPI) != RESET)) | |
{ | |
/* Call I2C Slave complete process */ | |
I2C_ITSlaveCplt(hi2c, ITFlags); | |
} | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_OK; | |
} | |
/** | |
* @brief Interrupt Sub-Routine which handle the Interrupt Flags Master Mode with DMA. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param ITFlags: Interrupt flags to handle. | |
* @param ITSources: Interrupt sources enabled. | |
* @retval HAL status | |
*/ | |
static HAL_StatusTypeDef I2C_Master_ISR_DMA(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, uint32_t ITSources) | |
{ | |
uint16_t devaddress = 0; | |
uint32_t xfermode = 0; | |
/* Process Locked */ | |
__HAL_LOCK(hi2c); | |
if(((ITFlags & I2C_FLAG_AF) != RESET) && ((ITSources & I2C_IT_NACKI) != RESET)) | |
{ | |
/* Clear NACK Flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); | |
/* Set corresponding Error Code */ | |
hi2c->ErrorCode |= HAL_I2C_ERROR_AF; | |
/* No need to generate STOP, it is automatically done */ | |
/* But enable STOP interrupt, to treat it */ | |
/* Error callback will be send during stop flag treatment */ | |
I2C_Enable_IRQ(hi2c, I2C_XFER_CPLT_IT); | |
/* Flush TX register */ | |
I2C_Flush_TXDR(hi2c); | |
} | |
else if(((ITFlags & I2C_FLAG_TCR) != RESET) && ((ITSources & I2C_IT_TCI) != RESET)) | |
{ | |
/* Disable TC interrupt */ | |
__HAL_I2C_DISABLE_IT(hi2c, I2C_IT_TCI); | |
if(hi2c->XferCount != 0) | |
{ | |
/* Recover Slave address */ | |
devaddress = (hi2c->Instance->CR2 & I2C_CR2_SADD); | |
/* Prepare the new XferSize to transfer */ | |
if(hi2c->XferCount > MAX_NBYTE_SIZE) | |
{ | |
hi2c->XferSize = MAX_NBYTE_SIZE; | |
xfermode = I2C_RELOAD_MODE; | |
} | |
else | |
{ | |
hi2c->XferSize = hi2c->XferCount; | |
xfermode = I2C_AUTOEND_MODE; | |
} | |
/* Set the new XferSize in Nbytes register */ | |
I2C_TransferConfig(hi2c, devaddress, hi2c->XferSize, xfermode, I2C_NO_STARTSTOP); | |
/* Update XferCount value */ | |
hi2c->XferCount -= hi2c->XferSize; | |
/* Enable DMA Request */ | |
if(hi2c->State == HAL_I2C_STATE_BUSY_RX) | |
{ | |
hi2c->Instance->CR1 |= I2C_CR1_RXDMAEN; | |
} | |
else | |
{ | |
hi2c->Instance->CR1 |= I2C_CR1_TXDMAEN; | |
} | |
} | |
else | |
{ | |
/* Wrong size Status regarding TCR flag event */ | |
/* Call the corresponding callback to inform upper layer of End of Transfer */ | |
I2C_ITError(hi2c, HAL_I2C_ERROR_SIZE); | |
} | |
} | |
else if(((ITFlags & I2C_FLAG_STOPF) != RESET) && ((ITSources & I2C_IT_STOPI) != RESET)) | |
{ | |
/* Call I2C Master complete process */ | |
I2C_ITMasterCplt(hi2c, ITFlags); | |
} | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_OK; | |
} | |
/** | |
* @brief Interrupt Sub-Routine which handle the Interrupt Flags Slave Mode with DMA. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param ITFlags: Interrupt flags to handle. | |
* @param ITSources: Interrupt sources enabled. | |
* @retval HAL status | |
*/ | |
static HAL_StatusTypeDef I2C_Slave_ISR_DMA(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, uint32_t ITSources) | |
{ | |
/* Process locked */ | |
__HAL_LOCK(hi2c); | |
if(((ITFlags & I2C_FLAG_AF) != RESET) && ((ITSources & I2C_IT_NACKI) != RESET)) | |
{ | |
/* Check that I2C transfer finished */ | |
/* if yes, normal use case, a NACK is sent by the MASTER when Transfer is finished */ | |
/* Mean XferCount == 0 */ | |
/* So clear Flag NACKF only */ | |
if(I2C_GET_DMA_REMAIN_DATA(hi2c) == 0) | |
{ | |
/* Clear NACK Flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); | |
} | |
else | |
{ | |
/* if no, error use case, a Non-Acknowledge of last Data is generated by the MASTER*/ | |
/* Clear NACK Flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); | |
/* Set ErrorCode corresponding to a Non-Acknowledge */ | |
hi2c->ErrorCode |= HAL_I2C_ERROR_AF; | |
} | |
} | |
else if(((ITFlags & I2C_FLAG_ADDR) != RESET) && ((ITSources & I2C_IT_ADDRI) != RESET)) | |
{ | |
/* Clear ADDR flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_ADDR); | |
} | |
else if(((ITFlags & I2C_FLAG_STOPF) != RESET) && ((ITSources & I2C_IT_STOPI) != RESET)) | |
{ | |
/* Call I2C Slave complete process */ | |
I2C_ITSlaveCplt(hi2c, ITFlags); | |
} | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_OK; | |
} | |
/** | |
* @brief Master sends target device address followed by internal memory address for write request. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param DevAddress: Target device address | |
* @param MemAddress: Internal memory address | |
* @param MemAddSize: Size of internal memory address | |
* @param Timeout: Timeout duration | |
* @param Tickstart Tick start value | |
* @retval HAL status | |
*/ | |
static HAL_StatusTypeDef I2C_RequestMemoryWrite(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress, uint16_t MemAddSize, uint32_t Timeout, uint32_t Tickstart) | |
{ | |
I2C_TransferConfig(hi2c,DevAddress,MemAddSize, I2C_RELOAD_MODE, I2C_GENERATE_START_WRITE); | |
/* Wait until TXIS flag is set */ | |
if(I2C_WaitOnTXISFlagUntilTimeout(hi2c, Timeout, Tickstart) != HAL_OK) | |
{ | |
if(hi2c->ErrorCode == HAL_I2C_ERROR_AF) | |
{ | |
return HAL_ERROR; | |
} | |
else | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
/* If Memory address size is 8Bit */ | |
if(MemAddSize == I2C_MEMADD_SIZE_8BIT) | |
{ | |
/* Send Memory Address */ | |
hi2c->Instance->TXDR = I2C_MEM_ADD_LSB(MemAddress); | |
} | |
/* If Memory address size is 16Bit */ | |
else | |
{ | |
/* Send MSB of Memory Address */ | |
hi2c->Instance->TXDR = I2C_MEM_ADD_MSB(MemAddress); | |
/* Wait until TXIS flag is set */ | |
if(I2C_WaitOnTXISFlagUntilTimeout(hi2c, Timeout, Tickstart) != HAL_OK) | |
{ | |
if(hi2c->ErrorCode == HAL_I2C_ERROR_AF) | |
{ | |
return HAL_ERROR; | |
} | |
else | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
/* Send LSB of Memory Address */ | |
hi2c->Instance->TXDR = I2C_MEM_ADD_LSB(MemAddress); | |
} | |
/* Wait until TCR flag is set */ | |
if(I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_TCR, RESET, Timeout, Tickstart) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
return HAL_OK; | |
} | |
/** | |
* @brief Master sends target device address followed by internal memory address for read request. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param DevAddress: Target device address | |
* @param MemAddress: Internal memory address | |
* @param MemAddSize: Size of internal memory address | |
* @param Timeout: Timeout duration | |
* @param Tickstart Tick start value | |
* @retval HAL status | |
*/ | |
static HAL_StatusTypeDef I2C_RequestMemoryRead(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress, uint16_t MemAddSize, uint32_t Timeout, uint32_t Tickstart) | |
{ | |
I2C_TransferConfig(hi2c,DevAddress,MemAddSize, I2C_SOFTEND_MODE, I2C_GENERATE_START_WRITE); | |
/* Wait until TXIS flag is set */ | |
if(I2C_WaitOnTXISFlagUntilTimeout(hi2c, Timeout, Tickstart) != HAL_OK) | |
{ | |
if(hi2c->ErrorCode == HAL_I2C_ERROR_AF) | |
{ | |
return HAL_ERROR; | |
} | |
else | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
/* If Memory address size is 8Bit */ | |
if(MemAddSize == I2C_MEMADD_SIZE_8BIT) | |
{ | |
/* Send Memory Address */ | |
hi2c->Instance->TXDR = I2C_MEM_ADD_LSB(MemAddress); | |
} | |
/* If Memory address size is 16Bit */ | |
else | |
{ | |
/* Send MSB of Memory Address */ | |
hi2c->Instance->TXDR = I2C_MEM_ADD_MSB(MemAddress); | |
/* Wait until TXIS flag is set */ | |
if(I2C_WaitOnTXISFlagUntilTimeout(hi2c, Timeout, Tickstart) != HAL_OK) | |
{ | |
if(hi2c->ErrorCode == HAL_I2C_ERROR_AF) | |
{ | |
return HAL_ERROR; | |
} | |
else | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
/* Send LSB of Memory Address */ | |
hi2c->Instance->TXDR = I2C_MEM_ADD_LSB(MemAddress); | |
} | |
/* Wait until TC flag is set */ | |
if(I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_TC, RESET, Timeout, Tickstart) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
return HAL_OK; | |
} | |
/** | |
* @brief I2C Address complete process callback. | |
* @param hi2c: I2C handle. | |
* @param ITFlags: Interrupt flags to handle. | |
* @retval None | |
*/ | |
static void I2C_ITAddrCplt(I2C_HandleTypeDef *hi2c, uint32_t ITFlags) | |
{ | |
uint8_t transferdirection = 0; | |
uint16_t slaveaddrcode = 0; | |
uint16_t ownadd1code = 0; | |
uint16_t ownadd2code = 0; | |
/* In case of Listen state, need to inform upper layer of address match code event */ | |
if((hi2c->State & HAL_I2C_STATE_LISTEN) == HAL_I2C_STATE_LISTEN) | |
{ | |
transferdirection = I2C_GET_DIR(hi2c); | |
slaveaddrcode = I2C_GET_ADDR_MATCH(hi2c); | |
ownadd1code = I2C_GET_OWN_ADDRESS1(hi2c); | |
ownadd2code = I2C_GET_OWN_ADDRESS2(hi2c); | |
/* If 10bits addressing mode is selected */ | |
if(hi2c->Init.AddressingMode == I2C_ADDRESSINGMODE_10BIT) | |
{ | |
if((slaveaddrcode & SlaveAddr_MSK) == ((ownadd1code >> SlaveAddr_SHIFT) & SlaveAddr_MSK)) | |
{ | |
slaveaddrcode = ownadd1code; | |
hi2c->AddrEventCount++; | |
if(hi2c->AddrEventCount == 2) | |
{ | |
/* Reset Address Event counter */ | |
hi2c->AddrEventCount = 0; | |
/* Clear ADDR flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c,I2C_FLAG_ADDR); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Call Slave Addr callback */ | |
HAL_I2C_AddrCallback(hi2c, transferdirection, slaveaddrcode); | |
} | |
} | |
else | |
{ | |
slaveaddrcode = ownadd2code; | |
/* Disable ADDR Interrupts */ | |
I2C_Disable_IRQ(hi2c, I2C_XFER_LISTEN_IT); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Call Slave Addr callback */ | |
HAL_I2C_AddrCallback(hi2c, transferdirection, slaveaddrcode); | |
} | |
} | |
/* else 7 bits addressing mode is selected */ | |
else | |
{ | |
/* Disable ADDR Interrupts */ | |
I2C_Disable_IRQ(hi2c, I2C_XFER_LISTEN_IT); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Call Slave Addr callback */ | |
HAL_I2C_AddrCallback(hi2c, transferdirection, slaveaddrcode); | |
} | |
} | |
/* Else clear address flag only */ | |
else | |
{ | |
/* Clear ADDR flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_ADDR); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
} | |
} | |
/** | |
* @brief I2C Master sequential complete process. | |
* @param hi2c: I2C handle. | |
* @retval None | |
*/ | |
static void I2C_ITMasterSequentialCplt(I2C_HandleTypeDef *hi2c) | |
{ | |
/* Reset I2C handle mode */ | |
hi2c->Mode = HAL_I2C_MODE_NONE; | |
/* No Generate Stop, to permit restart mode */ | |
/* The stop will be done at the end of transfer, when I2C_AUTOEND_MODE enable */ | |
if (hi2c->State == HAL_I2C_STATE_BUSY_TX) | |
{ | |
hi2c->State = HAL_I2C_STATE_READY; | |
hi2c->PreviousState = I2C_STATE_MASTER_BUSY_TX; | |
hi2c->XferISR = NULL; | |
/* Disable Interrupts */ | |
I2C_Disable_IRQ(hi2c, I2C_XFER_TX_IT); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Call the corresponding callback to inform upper layer of End of Transfer */ | |
HAL_I2C_MasterTxCpltCallback(hi2c); | |
} | |
/* hi2c->State == HAL_I2C_STATE_BUSY_RX */ | |
else | |
{ | |
hi2c->State = HAL_I2C_STATE_READY; | |
hi2c->PreviousState = I2C_STATE_MASTER_BUSY_RX; | |
hi2c->XferISR = NULL; | |
/* Disable Interrupts */ | |
I2C_Disable_IRQ(hi2c, I2C_XFER_RX_IT); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Call the corresponding callback to inform upper layer of End of Transfer */ | |
HAL_I2C_MasterRxCpltCallback(hi2c); | |
} | |
} | |
/** | |
* @brief I2C Slave sequential complete process. | |
* @param hi2c: I2C handle. | |
* @retval None | |
*/ | |
static void I2C_ITSlaveSequentialCplt(I2C_HandleTypeDef *hi2c) | |
{ | |
/* Reset I2C handle mode */ | |
hi2c->Mode = HAL_I2C_MODE_NONE; | |
if(hi2c->State == HAL_I2C_STATE_BUSY_TX_LISTEN) | |
{ | |
/* Remove HAL_I2C_STATE_SLAVE_BUSY_TX, keep only HAL_I2C_STATE_LISTEN */ | |
hi2c->State = HAL_I2C_STATE_LISTEN; | |
hi2c->PreviousState = I2C_STATE_SLAVE_BUSY_TX; | |
/* Disable Interrupts */ | |
I2C_Disable_IRQ(hi2c, I2C_XFER_TX_IT); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Call the Tx complete callback to inform upper layer of the end of transmit process */ | |
HAL_I2C_SlaveTxCpltCallback(hi2c); | |
} | |
else if(hi2c->State == HAL_I2C_STATE_BUSY_RX_LISTEN) | |
{ | |
/* Remove HAL_I2C_STATE_SLAVE_BUSY_RX, keep only HAL_I2C_STATE_LISTEN */ | |
hi2c->State = HAL_I2C_STATE_LISTEN; | |
hi2c->PreviousState = I2C_STATE_SLAVE_BUSY_RX; | |
/* Disable Interrupts */ | |
I2C_Disable_IRQ(hi2c, I2C_XFER_RX_IT); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Call the Rx complete callback to inform upper layer of the end of receive process */ | |
HAL_I2C_SlaveRxCpltCallback(hi2c); | |
} | |
} | |
/** | |
* @brief I2C Master complete process. | |
* @param hi2c: I2C handle. | |
* @param ITFlags: Interrupt flags to handle. | |
* @retval None | |
*/ | |
static void I2C_ITMasterCplt(I2C_HandleTypeDef *hi2c, uint32_t ITFlags) | |
{ | |
/* Clear STOP Flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF); | |
/* Clear Configuration Register 2 */ | |
I2C_RESET_CR2(hi2c); | |
/* Reset handle parameters */ | |
hi2c->PreviousState = I2C_STATE_NONE; | |
hi2c->XferISR = NULL; | |
hi2c->XferOptions = I2C_NO_OPTION_FRAME; | |
if((ITFlags & I2C_FLAG_AF) != RESET) | |
{ | |
/* Clear NACK Flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); | |
/* Set acknowledge error code */ | |
hi2c->ErrorCode |= HAL_I2C_ERROR_AF; | |
} | |
/* Flush TX register */ | |
I2C_Flush_TXDR(hi2c); | |
/* Disable Interrupts */ | |
I2C_Disable_IRQ(hi2c, I2C_XFER_TX_IT| I2C_XFER_RX_IT); | |
/* Call the corresponding callback to inform upper layer of End of Transfer */ | |
if(hi2c->ErrorCode != HAL_I2C_ERROR_NONE) | |
{ | |
/* Call the corresponding callback to inform upper layer of End of Transfer */ | |
I2C_ITError(hi2c, hi2c->ErrorCode); | |
} | |
/* hi2c->State == HAL_I2C_STATE_BUSY_TX */ | |
else if(hi2c->State == HAL_I2C_STATE_BUSY_TX) | |
{ | |
hi2c->State = HAL_I2C_STATE_READY; | |
if (hi2c->Mode == HAL_I2C_MODE_MEM) | |
{ | |
hi2c->Mode = HAL_I2C_MODE_NONE; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Call the corresponding callback to inform upper layer of End of Transfer */ | |
HAL_I2C_MemTxCpltCallback(hi2c); | |
} | |
else | |
{ | |
hi2c->Mode = HAL_I2C_MODE_NONE; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Call the corresponding callback to inform upper layer of End of Transfer */ | |
HAL_I2C_MasterTxCpltCallback(hi2c); | |
} | |
} | |
/* hi2c->State == HAL_I2C_STATE_BUSY_RX */ | |
else if(hi2c->State == HAL_I2C_STATE_BUSY_RX) | |
{ | |
hi2c->State = HAL_I2C_STATE_READY; | |
if (hi2c->Mode == HAL_I2C_MODE_MEM) | |
{ | |
hi2c->Mode = HAL_I2C_MODE_NONE; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
HAL_I2C_MemRxCpltCallback(hi2c); | |
} | |
else | |
{ | |
hi2c->Mode = HAL_I2C_MODE_NONE; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
HAL_I2C_MasterRxCpltCallback(hi2c); | |
} | |
} | |
} | |
/** | |
* @brief I2C Slave complete process. | |
* @param hi2c: I2C handle. | |
* @param ITFlags: Interrupt flags to handle. | |
* @retval None | |
*/ | |
static void I2C_ITSlaveCplt(I2C_HandleTypeDef *hi2c, uint32_t ITFlags) | |
{ | |
/* Clear STOP Flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF); | |
/* Clear ADDR flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c,I2C_FLAG_ADDR); | |
/* Disable all interrupts */ | |
I2C_Disable_IRQ(hi2c, I2C_XFER_LISTEN_IT | I2C_XFER_TX_IT | I2C_XFER_RX_IT); | |
/* Disable Address Acknowledge */ | |
hi2c->Instance->CR2 |= I2C_CR2_NACK; | |
/* Clear Configuration Register 2 */ | |
I2C_RESET_CR2(hi2c); | |
/* Flush TX register */ | |
I2C_Flush_TXDR(hi2c); | |
/* If a DMA is ongoing, Update handle size context */ | |
if(((hi2c->Instance->CR1 & I2C_CR1_TXDMAEN) == I2C_CR1_TXDMAEN) || | |
((hi2c->Instance->CR1 & I2C_CR1_RXDMAEN) == I2C_CR1_RXDMAEN)) | |
{ | |
if((hi2c->XferSize - I2C_GET_DMA_REMAIN_DATA(hi2c)) != hi2c->XferSize) | |
{ | |
hi2c->XferSize = I2C_GET_DMA_REMAIN_DATA(hi2c); | |
hi2c->XferCount += hi2c->XferSize; | |
/* Set ErrorCode corresponding to a Non-Acknowledge */ | |
hi2c->ErrorCode |= HAL_I2C_ERROR_AF; | |
} | |
} | |
/* Store Last receive data if any */ | |
if(((ITFlags & I2C_FLAG_RXNE) != RESET)) | |
{ | |
/* Read data from RXDR */ | |
(*hi2c->pBuffPtr++) = hi2c->Instance->RXDR; | |
if((hi2c->XferSize > 0)) | |
{ | |
hi2c->XferSize--; | |
hi2c->XferCount--; | |
/* Set ErrorCode corresponding to a Non-Acknowledge */ | |
hi2c->ErrorCode |= HAL_I2C_ERROR_AF; | |
} | |
} | |
hi2c->PreviousState = I2C_STATE_NONE; | |
hi2c->Mode = HAL_I2C_MODE_NONE; | |
hi2c->XferISR = NULL; | |
if(hi2c->ErrorCode != HAL_I2C_ERROR_NONE) | |
{ | |
hi2c->XferOptions = I2C_NO_OPTION_FRAME; | |
hi2c->State = HAL_I2C_STATE_READY; | |
/* Call the corresponding callback to inform upper layer of End of Transfer */ | |
I2C_ITError(hi2c, hi2c->ErrorCode); | |
} | |
else if(hi2c->XferOptions != I2C_NO_OPTION_FRAME) | |
{ | |
hi2c->XferOptions = I2C_NO_OPTION_FRAME; | |
hi2c->State = HAL_I2C_STATE_READY; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Call the Listen Complete callback, to inform upper layer of the end of Listen usecase */ | |
HAL_I2C_ListenCpltCallback(hi2c); | |
} | |
/* Call the corresponding callback to inform upper layer of End of Transfer */ | |
else if(hi2c->State == HAL_I2C_STATE_BUSY_RX) | |
{ | |
hi2c->State = HAL_I2C_STATE_READY; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Call the Slave Rx Complete callback */ | |
HAL_I2C_SlaveRxCpltCallback(hi2c); | |
} | |
else | |
{ | |
hi2c->State = HAL_I2C_STATE_READY; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Call the Slave Tx Complete callback */ | |
HAL_I2C_SlaveTxCpltCallback(hi2c); | |
} | |
} | |
/** | |
* @brief I2C Listen complete process. | |
* @param hi2c: I2C handle. | |
* @param ITFlags: Interrupt flags to handle. | |
* @retval None | |
*/ | |
static void I2C_ITListenCplt(I2C_HandleTypeDef *hi2c, uint32_t ITFlags) | |
{ | |
/* Reset handle parameters */ | |
hi2c->XferOptions = I2C_NO_OPTION_FRAME; | |
hi2c->PreviousState = I2C_STATE_NONE; | |
hi2c->State = HAL_I2C_STATE_READY; | |
hi2c->Mode = HAL_I2C_MODE_NONE; | |
hi2c->XferISR = NULL; | |
/* Store Last receive data if any */ | |
if(((ITFlags & I2C_FLAG_RXNE) != RESET)) | |
{ | |
/* Read data from RXDR */ | |
(*hi2c->pBuffPtr++) = hi2c->Instance->RXDR; | |
if((hi2c->XferSize > 0)) | |
{ | |
hi2c->XferSize--; | |
hi2c->XferCount--; | |
/* Set ErrorCode corresponding to a Non-Acknowledge */ | |
hi2c->ErrorCode |= HAL_I2C_ERROR_AF; | |
} | |
} | |
/* Disable all Interrupts*/ | |
I2C_Disable_IRQ(hi2c, I2C_XFER_LISTEN_IT | I2C_XFER_RX_IT | I2C_XFER_TX_IT); | |
/* Clear NACK Flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Call the Listen Complete callback, to inform upper layer of the end of Listen usecase */ | |
HAL_I2C_ListenCpltCallback(hi2c); | |
} | |
/** | |
* @brief I2C interrupts error process. | |
* @param hi2c: I2C handle. | |
* @param ErrorCode: Error code to handle. | |
* @retval None | |
*/ | |
static void I2C_ITError(I2C_HandleTypeDef *hi2c, uint32_t ErrorCode) | |
{ | |
/* Reset handle parameters */ | |
hi2c->Mode = HAL_I2C_MODE_NONE; | |
hi2c->XferOptions = I2C_NO_OPTION_FRAME; | |
hi2c->XferCount = 0; | |
/* Set new error code */ | |
hi2c->ErrorCode |= ErrorCode; | |
/* Disable Interrupts */ | |
if((hi2c->State == HAL_I2C_STATE_LISTEN) || | |
(hi2c->State == HAL_I2C_STATE_BUSY_TX_LISTEN) || | |
(hi2c->State == HAL_I2C_STATE_BUSY_RX_LISTEN)) | |
{ | |
/* Disable all interrupts, except interrupts related to LISTEN state */ | |
I2C_Disable_IRQ(hi2c, I2C_XFER_RX_IT | I2C_XFER_TX_IT); | |
/* keep HAL_I2C_STATE_LISTEN if set */ | |
hi2c->State = HAL_I2C_STATE_LISTEN; | |
hi2c->PreviousState = I2C_STATE_NONE; | |
hi2c->XferISR = I2C_Slave_ISR_IT; | |
} | |
else | |
{ | |
/* Disable all interrupts */ | |
I2C_Disable_IRQ(hi2c, I2C_XFER_LISTEN_IT | I2C_XFER_RX_IT | I2C_XFER_TX_IT); | |
/* Set HAL_I2C_STATE_READY */ | |
hi2c->State = HAL_I2C_STATE_READY; | |
hi2c->PreviousState = I2C_STATE_NONE; | |
hi2c->XferISR = NULL; | |
} | |
/* Abort DMA TX transfer if any */ | |
if((hi2c->Instance->CR1 & I2C_CR1_TXDMAEN) == I2C_CR1_TXDMAEN) | |
{ | |
hi2c->Instance->CR1 &= ~I2C_CR1_TXDMAEN; | |
/* Set the I2C DMA Abort callback : | |
will lead to call HAL_I2C_ErrorCallback() at end of DMA abort procedure */ | |
hi2c->hdmatx->XferAbortCallback = I2C_DMAAbort; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Abort DMA TX */ | |
if(HAL_DMA_Abort_IT(hi2c->hdmatx) != HAL_OK) | |
{ | |
/* Call Directly XferAbortCallback function in case of error */ | |
hi2c->hdmatx->XferAbortCallback(hi2c->hdmatx); | |
} | |
} | |
/* Abort DMA RX transfer if any */ | |
else if((hi2c->Instance->CR1 & I2C_CR1_RXDMAEN) == I2C_CR1_RXDMAEN) | |
{ | |
hi2c->Instance->CR1 &= ~I2C_CR1_RXDMAEN; | |
/* Set the I2C DMA Abort callback : | |
will lead to call HAL_I2C_ErrorCallback() at end of DMA abort procedure */ | |
hi2c->hdmarx->XferAbortCallback = I2C_DMAAbort; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Abort DMA RX */ | |
if(HAL_DMA_Abort_IT(hi2c->hdmarx) != HAL_OK) | |
{ | |
/* Call Directly hi2c->hdmarx->XferAbortCallback function in case of error */ | |
hi2c->hdmarx->XferAbortCallback(hi2c->hdmarx); | |
} | |
} | |
else if(hi2c->ErrorCode == HAL_I2C_ERROR_ABORT) | |
{ | |
hi2c->ErrorCode &= ~HAL_I2C_ERROR_ABORT; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Call the corresponding callback to inform upper layer of End of Transfer */ | |
HAL_I2C_AbortCpltCallback(hi2c); | |
} | |
else | |
{ | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
/* Call the corresponding callback to inform upper layer of End of Transfer */ | |
HAL_I2C_ErrorCallback(hi2c); | |
} | |
} | |
/** | |
* @brief I2C Tx data register flush process. | |
* @param hi2c: I2C handle. | |
* @retval None | |
*/ | |
static void I2C_Flush_TXDR(I2C_HandleTypeDef *hi2c) | |
{ | |
/* If a pending TXIS flag is set */ | |
/* Write a dummy data in TXDR to clear it */ | |
if(__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_TXIS) != RESET) | |
{ | |
hi2c->Instance->TXDR = 0x00; | |
} | |
/* Flush TX register if not empty */ | |
if(__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_TXE) == RESET) | |
{ | |
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_TXE); | |
} | |
} | |
/** | |
* @brief DMA I2C master transmit process complete callback. | |
* @param hdma: DMA handle | |
* @retval None | |
*/ | |
static void I2C_DMAMasterTransmitCplt(DMA_HandleTypeDef *hdma) | |
{ | |
I2C_HandleTypeDef* hi2c = (I2C_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent; | |
/* Disable DMA Request */ | |
hi2c->Instance->CR1 &= ~I2C_CR1_TXDMAEN; | |
/* If last transfer, enable STOP interrupt */ | |
if(hi2c->XferCount == 0) | |
{ | |
/* Enable STOP interrupt */ | |
I2C_Enable_IRQ(hi2c, I2C_XFER_CPLT_IT); | |
} | |
/* else prepare a new DMA transfer and enable TCReload interrupt */ | |
else | |
{ | |
/* Update Buffer pointer */ | |
hi2c->pBuffPtr += hi2c->XferSize; | |
/* Set the XferSize to transfer */ | |
if(hi2c->XferCount > MAX_NBYTE_SIZE) | |
{ | |
hi2c->XferSize = MAX_NBYTE_SIZE; | |
} | |
else | |
{ | |
hi2c->XferSize = hi2c->XferCount; | |
} | |
/* Enable the DMA channel */ | |
HAL_DMA_Start_IT(hi2c->hdmatx, (uint32_t)hi2c->pBuffPtr, (uint32_t)&hi2c->Instance->TXDR, hi2c->XferSize); | |
/* Enable TC interrupts */ | |
I2C_Enable_IRQ(hi2c, I2C_XFER_RELOAD_IT); | |
} | |
} | |
/** | |
* @brief DMA I2C slave transmit process complete callback. | |
* @param hdma: DMA handle | |
* @retval None | |
*/ | |
static void I2C_DMASlaveTransmitCplt(DMA_HandleTypeDef *hdma) | |
{ | |
/* No specific action, Master fully manage the generation of STOP condition */ | |
/* Mean that this generation can arrive at any time, at the end or during DMA process */ | |
/* So STOP condition should be manage through Interrupt treatment */ | |
} | |
/** | |
* @brief DMA I2C master receive process complete callback. | |
* @param hdma: DMA handle | |
* @retval None | |
*/ | |
static void I2C_DMAMasterReceiveCplt(DMA_HandleTypeDef *hdma) | |
{ | |
I2C_HandleTypeDef* hi2c = (I2C_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent; | |
/* Disable DMA Request */ | |
hi2c->Instance->CR1 &= ~I2C_CR1_RXDMAEN; | |
/* If last transfer, enable STOP interrupt */ | |
if(hi2c->XferCount == 0) | |
{ | |
/* Enable STOP interrupt */ | |
I2C_Enable_IRQ(hi2c, I2C_XFER_CPLT_IT); | |
} | |
/* else prepare a new DMA transfer and enable TCReload interrupt */ | |
else | |
{ | |
/* Update Buffer pointer */ | |
hi2c->pBuffPtr += hi2c->XferSize; | |
/* Set the XferSize to transfer */ | |
if(hi2c->XferCount > MAX_NBYTE_SIZE) | |
{ | |
hi2c->XferSize = MAX_NBYTE_SIZE; | |
} | |
else | |
{ | |
hi2c->XferSize = hi2c->XferCount; | |
} | |
/* Enable the DMA channel */ | |
HAL_DMA_Start_IT(hi2c->hdmarx, (uint32_t)&hi2c->Instance->RXDR, (uint32_t)hi2c->pBuffPtr, hi2c->XferSize); | |
/* Enable TC interrupts */ | |
I2C_Enable_IRQ(hi2c, I2C_XFER_RELOAD_IT); | |
} | |
} | |
/** | |
* @brief DMA I2C slave receive process complete callback. | |
* @param hdma: DMA handle | |
* @retval None | |
*/ | |
static void I2C_DMASlaveReceiveCplt(DMA_HandleTypeDef *hdma) | |
{ | |
/* No specific action, Master fully manage the generation of STOP condition */ | |
/* Mean that this generation can arrive at any time, at the end or during DMA process */ | |
/* So STOP condition should be manage through Interrupt treatment */ | |
} | |
/** | |
* @brief DMA I2C communication error callback. | |
* @param hdma: DMA handle | |
* @retval None | |
*/ | |
static void I2C_DMAError(DMA_HandleTypeDef *hdma) | |
{ | |
I2C_HandleTypeDef* hi2c = ( I2C_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; | |
/* Disable Acknowledge */ | |
hi2c->Instance->CR2 |= I2C_CR2_NACK; | |
/* Call the corresponding callback to inform upper layer of End of Transfer */ | |
I2C_ITError(hi2c, HAL_I2C_ERROR_DMA); | |
} | |
/** | |
* @brief DMA I2C communication abort callback | |
* (To be called at end of DMA Abort procedure). | |
* @param hdma: DMA handle. | |
* @retval None | |
*/ | |
static void I2C_DMAAbort(DMA_HandleTypeDef *hdma) | |
{ | |
I2C_HandleTypeDef* hi2c = ( I2C_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; | |
/* Disable Acknowledge */ | |
hi2c->Instance->CR2 |= I2C_CR2_NACK; | |
/* Reset AbortCpltCallback */ | |
hi2c->hdmatx->XferAbortCallback = NULL; | |
hi2c->hdmarx->XferAbortCallback = NULL; | |
/* Check if come from abort from user */ | |
if(hi2c->ErrorCode == HAL_I2C_ERROR_ABORT) | |
{ | |
hi2c->ErrorCode &= ~HAL_I2C_ERROR_ABORT; | |
/* Call the corresponding callback to inform upper layer of End of Transfer */ | |
HAL_I2C_AbortCpltCallback(hi2c); | |
} | |
else | |
{ | |
/* Call the corresponding callback to inform upper layer of End of Transfer */ | |
HAL_I2C_ErrorCallback(hi2c); | |
} | |
} | |
/** | |
* @brief This function handles I2C Communication Timeout. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param Flag: Specifies the I2C flag to check. | |
* @param Status: The new Flag status (SET or RESET). | |
* @param Timeout: Timeout duration | |
* @param Tickstart: Tick start value | |
* @retval HAL status | |
*/ | |
static HAL_StatusTypeDef I2C_WaitOnFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Flag, FlagStatus Status, uint32_t Timeout, uint32_t Tickstart) | |
{ | |
while((__HAL_I2C_GET_FLAG(hi2c, Flag) ? SET : RESET) == Status) | |
{ | |
/* Check for the Timeout */ | |
if(Timeout != HAL_MAX_DELAY) | |
{ | |
if((Timeout == 0)||((HAL_GetTick() - Tickstart ) > Timeout)) | |
{ | |
hi2c->State= HAL_I2C_STATE_READY; | |
hi2c->Mode = HAL_I2C_MODE_NONE; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
return HAL_OK; | |
} | |
/** | |
* @brief This function handles I2C Communication Timeout for specific usage of TXIS flag. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param Timeout: Timeout duration | |
* @param Tickstart: Tick start value | |
* @retval HAL status | |
*/ | |
static HAL_StatusTypeDef I2C_WaitOnTXISFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Timeout, uint32_t Tickstart) | |
{ | |
while(__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_TXIS) == RESET) | |
{ | |
/* Check if a NACK is detected */ | |
if(I2C_IsAcknowledgeFailed(hi2c, Timeout, Tickstart) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
/* Check for the Timeout */ | |
if(Timeout != HAL_MAX_DELAY) | |
{ | |
if((Timeout == 0)||((HAL_GetTick() - Tickstart) > Timeout)) | |
{ | |
hi2c->ErrorCode |= HAL_I2C_ERROR_TIMEOUT; | |
hi2c->State= HAL_I2C_STATE_READY; | |
hi2c->Mode = HAL_I2C_MODE_NONE; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
return HAL_OK; | |
} | |
/** | |
* @brief This function handles I2C Communication Timeout for specific usage of STOP flag. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param Timeout: Timeout duration | |
* @param Tickstart: Tick start value | |
* @retval HAL status | |
*/ | |
static HAL_StatusTypeDef I2C_WaitOnSTOPFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Timeout, uint32_t Tickstart) | |
{ | |
while(__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_STOPF) == RESET) | |
{ | |
/* Check if a NACK is detected */ | |
if(I2C_IsAcknowledgeFailed(hi2c, Timeout, Tickstart) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
/* Check for the Timeout */ | |
if((Timeout == 0)||((HAL_GetTick() - Tickstart) > Timeout)) | |
{ | |
hi2c->ErrorCode |= HAL_I2C_ERROR_TIMEOUT; | |
hi2c->State= HAL_I2C_STATE_READY; | |
hi2c->Mode = HAL_I2C_MODE_NONE; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_TIMEOUT; | |
} | |
} | |
return HAL_OK; | |
} | |
/** | |
* @brief This function handles I2C Communication Timeout for specific usage of RXNE flag. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param Timeout: Timeout duration | |
* @param Tickstart: Tick start value | |
* @retval HAL status | |
*/ | |
static HAL_StatusTypeDef I2C_WaitOnRXNEFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Timeout, uint32_t Tickstart) | |
{ | |
while(__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_RXNE) == RESET) | |
{ | |
/* Check if a NACK is detected */ | |
if(I2C_IsAcknowledgeFailed(hi2c, Timeout, Tickstart) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
/* Check if a STOPF is detected */ | |
if(__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_STOPF) == SET) | |
{ | |
/* Clear STOP Flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF); | |
/* Clear Configuration Register 2 */ | |
I2C_RESET_CR2(hi2c); | |
hi2c->ErrorCode = HAL_I2C_ERROR_NONE; | |
hi2c->State= HAL_I2C_STATE_READY; | |
hi2c->Mode = HAL_I2C_MODE_NONE; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_ERROR; | |
} | |
/* Check for the Timeout */ | |
if((Timeout == 0)||((HAL_GetTick() - Tickstart) > Timeout)) | |
{ | |
hi2c->ErrorCode |= HAL_I2C_ERROR_TIMEOUT; | |
hi2c->State= HAL_I2C_STATE_READY; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_TIMEOUT; | |
} | |
} | |
return HAL_OK; | |
} | |
/** | |
* @brief This function handles Acknowledge failed detection during an I2C Communication. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param Timeout: Timeout duration | |
* @param Tickstart: Tick start value | |
* @retval HAL status | |
*/ | |
static HAL_StatusTypeDef I2C_IsAcknowledgeFailed(I2C_HandleTypeDef *hi2c, uint32_t Timeout, uint32_t Tickstart) | |
{ | |
if(__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_AF) == SET) | |
{ | |
/* Wait until STOP Flag is reset */ | |
/* AutoEnd should be initiate after AF */ | |
while(__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_STOPF) == RESET) | |
{ | |
/* Check for the Timeout */ | |
if(Timeout != HAL_MAX_DELAY) | |
{ | |
if((Timeout == 0)||((HAL_GetTick() - Tickstart) > Timeout)) | |
{ | |
hi2c->State= HAL_I2C_STATE_READY; | |
hi2c->Mode = HAL_I2C_MODE_NONE; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
/* Clear NACKF Flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); | |
/* Clear STOP Flag */ | |
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF); | |
/* Flush TX register */ | |
I2C_Flush_TXDR(hi2c); | |
/* Clear Configuration Register 2 */ | |
I2C_RESET_CR2(hi2c); | |
hi2c->ErrorCode = HAL_I2C_ERROR_AF; | |
hi2c->State= HAL_I2C_STATE_READY; | |
hi2c->Mode = HAL_I2C_MODE_NONE; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hi2c); | |
return HAL_ERROR; | |
} | |
return HAL_OK; | |
} | |
/** | |
* @brief Handles I2Cx communication when starting transfer or during transfer (TC or TCR flag are set). | |
* @param hi2c: I2C handle. | |
* @param DevAddress: Specifies the slave address to be programmed. | |
* @param Size: Specifies the number of bytes to be programmed. | |
* This parameter must be a value between 0 and 255. | |
* @param Mode: New state of the I2C START condition generation. | |
* This parameter can be a value of @ref I2C_RELOAD_END_MODE. | |
* @param Request: New state of the I2C START condition generation. | |
* This parameter can be a value of I2C_START_STOP_MODE. | |
* @retval None | |
*/ | |
static void I2C_TransferConfig(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t Size, uint32_t Mode, uint32_t Request) | |
{ | |
uint32_t tmpreg = 0; | |
/* Check the parameters */ | |
assert_param(IS_I2C_ALL_INSTANCE(hi2c->Instance)); | |
assert_param(IS_TRANSFER_MODE(Mode)); | |
assert_param(IS_TRANSFER_REQUEST(Request)); | |
/* Get the CR2 register value */ | |
tmpreg = hi2c->Instance->CR2; | |
/* clear tmpreg specific bits */ | |
tmpreg &= (uint32_t)~((uint32_t)(I2C_CR2_SADD | I2C_CR2_NBYTES | I2C_CR2_RELOAD | I2C_CR2_AUTOEND | I2C_CR2_RD_WRN | I2C_CR2_START | I2C_CR2_STOP)); | |
/* update tmpreg */ | |
tmpreg |= (uint32_t)(((uint32_t)DevAddress & I2C_CR2_SADD) | (((uint32_t)Size << 16 ) & I2C_CR2_NBYTES) | \ | |
(uint32_t)Mode | (uint32_t)Request); | |
/* update CR2 register */ | |
hi2c->Instance->CR2 = tmpreg; | |
} | |
/** | |
* @brief Manage the enabling of Interrupts. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param InterruptRequest: Value of @ref I2C_Interrupt_configuration_definition. | |
* @retval HAL status | |
*/ | |
static HAL_StatusTypeDef I2C_Enable_IRQ(I2C_HandleTypeDef *hi2c, uint16_t InterruptRequest) | |
{ | |
uint32_t tmpisr = 0; | |
if((hi2c->XferISR == I2C_Master_ISR_DMA) || \ | |
(hi2c->XferISR == I2C_Slave_ISR_DMA)) | |
{ | |
if((InterruptRequest & I2C_XFER_LISTEN_IT) == I2C_XFER_LISTEN_IT) | |
{ | |
/* Enable ERR, STOP, NACK and ADDR interrupts */ | |
tmpisr |= I2C_IT_ADDRI | I2C_IT_STOPI | I2C_IT_NACKI | I2C_IT_ERRI; | |
} | |
if((InterruptRequest & I2C_XFER_ERROR_IT) == I2C_XFER_ERROR_IT) | |
{ | |
/* Enable ERR and NACK interrupts */ | |
tmpisr |= I2C_IT_ERRI | I2C_IT_NACKI; | |
} | |
if((InterruptRequest & I2C_XFER_CPLT_IT) == I2C_XFER_CPLT_IT) | |
{ | |
/* Enable STOP interrupts */ | |
tmpisr |= I2C_IT_STOPI; | |
} | |
if((InterruptRequest & I2C_XFER_RELOAD_IT) == I2C_XFER_RELOAD_IT) | |
{ | |
/* Enable TC interrupts */ | |
tmpisr |= I2C_IT_TCI; | |
} | |
} | |
else | |
{ | |
if((InterruptRequest & I2C_XFER_LISTEN_IT) == I2C_XFER_LISTEN_IT) | |
{ | |
/* Enable ERR, STOP, NACK, and ADDR interrupts */ | |
tmpisr |= I2C_IT_ADDRI | I2C_IT_STOPI | I2C_IT_NACKI | I2C_IT_ERRI; | |
} | |
if((InterruptRequest & I2C_XFER_TX_IT) == I2C_XFER_TX_IT) | |
{ | |
/* Enable ERR, TC, STOP, NACK and RXI interrupts */ | |
tmpisr |= I2C_IT_ERRI | I2C_IT_TCI | I2C_IT_STOPI | I2C_IT_NACKI | I2C_IT_TXI; | |
} | |
if((InterruptRequest & I2C_XFER_RX_IT) == I2C_XFER_RX_IT) | |
{ | |
/* Enable ERR, TC, STOP, NACK and TXI interrupts */ | |
tmpisr |= I2C_IT_ERRI | I2C_IT_TCI | I2C_IT_STOPI | I2C_IT_NACKI | I2C_IT_RXI; | |
} | |
if((InterruptRequest & I2C_XFER_CPLT_IT) == I2C_XFER_CPLT_IT) | |
{ | |
/* Enable STOP interrupts */ | |
tmpisr |= I2C_IT_STOPI; | |
} | |
} | |
/* Enable interrupts only at the end */ | |
/* to avoid the risk of I2C interrupt handle execution before */ | |
/* all interrupts requested done */ | |
__HAL_I2C_ENABLE_IT(hi2c, tmpisr); | |
return HAL_OK; | |
} | |
/** | |
* @brief Manage the disabling of Interrupts. | |
* @param hi2c: Pointer to a I2C_HandleTypeDef structure that contains | |
* the configuration information for the specified I2C. | |
* @param InterruptRequest: Value of @ref I2C_Interrupt_configuration_definition. | |
* @retval HAL status | |
*/ | |
static HAL_StatusTypeDef I2C_Disable_IRQ(I2C_HandleTypeDef *hi2c, uint16_t InterruptRequest) | |
{ | |
uint32_t tmpisr = 0; | |
if((InterruptRequest & I2C_XFER_TX_IT) == I2C_XFER_TX_IT) | |
{ | |
/* Disable TC and TXI interrupts */ | |
tmpisr |= I2C_IT_TCI | I2C_IT_TXI; | |
if((hi2c->State & HAL_I2C_STATE_LISTEN) != HAL_I2C_STATE_LISTEN) | |
{ | |
/* Disable NACK and STOP interrupts */ | |
tmpisr |= I2C_IT_STOPI | I2C_IT_NACKI | I2C_IT_ERRI; | |
} | |
} | |
if((InterruptRequest & I2C_XFER_RX_IT) == I2C_XFER_RX_IT) | |
{ | |
/* Disable TC and RXI interrupts */ | |
tmpisr |= I2C_IT_TCI | I2C_IT_RXI; | |
if((hi2c->State & HAL_I2C_STATE_LISTEN) != HAL_I2C_STATE_LISTEN) | |
{ | |
/* Disable NACK and STOP interrupts */ | |
tmpisr |= I2C_IT_STOPI | I2C_IT_NACKI | I2C_IT_ERRI; | |
} | |
} | |
if((InterruptRequest & I2C_XFER_LISTEN_IT) == I2C_XFER_LISTEN_IT) | |
{ | |
/* Disable ADDR, NACK and STOP interrupts */ | |
tmpisr |= I2C_IT_ADDRI | I2C_IT_STOPI | I2C_IT_NACKI | I2C_IT_ERRI; | |
} | |
if((InterruptRequest & I2C_XFER_ERROR_IT) == I2C_XFER_ERROR_IT) | |
{ | |
/* Enable ERR and NACK interrupts */ | |
tmpisr |= I2C_IT_ERRI | I2C_IT_NACKI; | |
} | |
if((InterruptRequest & I2C_XFER_CPLT_IT) == I2C_XFER_CPLT_IT) | |
{ | |
/* Enable STOP interrupts */ | |
tmpisr |= I2C_IT_STOPI; | |
} | |
if((InterruptRequest & I2C_XFER_RELOAD_IT) == I2C_XFER_RELOAD_IT) | |
{ | |
/* Enable TC interrupts */ | |
tmpisr |= I2C_IT_TCI; | |
} | |
/* Disable interrupts only at the end */ | |
/* to avoid a breaking situation like at "t" time */ | |
/* all disable interrupts request are not done */ | |
__HAL_I2C_DISABLE_IT(hi2c, tmpisr); | |
return HAL_OK; | |
} | |
/** | |
* @} | |
*/ | |
#endif /* HAL_I2C_MODULE_ENABLED */ | |
/** | |
* @} | |
*/ | |
/** | |
* @} | |
*/ | |
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |