/** | |
****************************************************************************** | |
* @file stm32f7xx_hal_rcc_ex.c | |
* @author MCD Application Team | |
* @version V1.1.1 | |
* @date 01-July-2016 | |
* @brief Extension RCC HAL module driver. | |
* This file provides firmware functions to manage the following | |
* functionalities RCC extension peripheral: | |
* + Extended Peripheral Control functions | |
* | |
****************************************************************************** | |
* @attention | |
* | |
* <h2><center>© COPYRIGHT(c) 2016 STMicroelectronics</center></h2> | |
* | |
* Redistribution and use in source and binary forms, with or without modification, | |
* are permitted provided that the following conditions are met: | |
* 1. Redistributions of source code must retain the above copyright notice, | |
* this list of conditions and the following disclaimer. | |
* 2. Redistributions in binary form must reproduce the above copyright notice, | |
* this list of conditions and the following disclaimer in the documentation | |
* and/or other materials provided with the distribution. | |
* 3. Neither the name of STMicroelectronics nor the names of its contributors | |
* may be used to endorse or promote products derived from this software | |
* without specific prior written permission. | |
* | |
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" | |
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE | |
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE | |
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE | |
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL | |
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR | |
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER | |
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, | |
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE | |
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. | |
* | |
****************************************************************************** | |
*/ | |
/* Includes ------------------------------------------------------------------*/ | |
#include "stm32f7xx_hal.h" | |
/** @addtogroup STM32F7xx_HAL_Driver | |
* @{ | |
*/ | |
/** @defgroup RCCEx RCCEx | |
* @brief RCCEx HAL module driver | |
* @{ | |
*/ | |
#ifdef HAL_RCC_MODULE_ENABLED | |
/* Private typedef -----------------------------------------------------------*/ | |
/* Private define ------------------------------------------------------------*/ | |
/** @defgroup RCCEx_Private_Defines RCCEx Private Defines | |
* @{ | |
*/ | |
#define PLLI2S_TIMEOUT_VALUE 100 /* Timeout value fixed to 100 ms */ | |
#define PLLSAI_TIMEOUT_VALUE 100 /* Timeout value fixed to 100 ms */ | |
/** | |
* @} | |
*/ | |
/* Private macro -------------------------------------------------------------*/ | |
/** @defgroup RCCEx_Private_Macros RCCEx Private Macros | |
* @{ | |
*/ | |
/** | |
* @} | |
*/ | |
/** @defgroup RCCEx_Private_Macros RCCEx Private Macros | |
* @{ | |
*/ | |
/** | |
* @} | |
*/ | |
/* Private variables ---------------------------------------------------------*/ | |
/* Private function prototypes -----------------------------------------------*/ | |
/* Private functions ---------------------------------------------------------*/ | |
/** @defgroup RCCEx_Exported_Functions RCCEx Exported Functions | |
* @{ | |
*/ | |
/** @defgroup RCCEx_Exported_Functions_Group1 Extended Peripheral Control functions | |
* @brief Extended Peripheral Control functions | |
* | |
@verbatim | |
=============================================================================== | |
##### Extended Peripheral Control functions ##### | |
=============================================================================== | |
[..] | |
This subsection provides a set of functions allowing to control the RCC Clocks | |
frequencies. | |
[..] | |
(@) Important note: Care must be taken when HAL_RCCEx_PeriphCLKConfig() is used to | |
select the RTC clock source; in this case the Backup domain will be reset in | |
order to modify the RTC Clock source, as consequence RTC registers (including | |
the backup registers) and RCC_BDCR register will be set to their reset values. | |
@endverbatim | |
* @{ | |
*/ | |
/** | |
* @brief Initializes the RCC extended peripherals clocks according to the specified | |
* parameters in the RCC_PeriphCLKInitTypeDef. | |
* @param PeriphClkInit: pointer to an RCC_PeriphCLKInitTypeDef structure that | |
* contains the configuration information for the Extended Peripherals | |
* clocks(I2S, SAI, LTDC, RTC, TIM, UARTs, USARTs, LTPIM, SDMMC...). | |
* | |
* @note Care must be taken when HAL_RCCEx_PeriphCLKConfig() is used to select | |
* the RTC clock source; in this case the Backup domain will be reset in | |
* order to modify the RTC Clock source, as consequence RTC registers (including | |
* the backup registers) are set to their reset values. | |
* | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_RCCEx_PeriphCLKConfig(RCC_PeriphCLKInitTypeDef *PeriphClkInit) | |
{ | |
uint32_t tickstart = 0; | |
uint32_t tmpreg0 = 0; | |
uint32_t tmpreg1 = 0; | |
uint32_t plli2sused = 0; | |
uint32_t pllsaiused = 0; | |
/* Check the parameters */ | |
assert_param(IS_RCC_PERIPHCLOCK(PeriphClkInit->PeriphClockSelection)); | |
/*----------------------------------- I2S configuration ----------------------------------*/ | |
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S) == (RCC_PERIPHCLK_I2S)) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_I2SCLKSOURCE(PeriphClkInit->I2sClockSelection)); | |
/* Configure I2S Clock source */ | |
__HAL_RCC_I2S_CONFIG(PeriphClkInit->I2sClockSelection); | |
/* Enable the PLLI2S when it's used as clock source for I2S */ | |
if(PeriphClkInit->I2sClockSelection == RCC_I2SCLKSOURCE_PLLI2S) | |
{ | |
plli2sused = 1; | |
} | |
} | |
/*------------------------------------ SAI1 configuration --------------------------------------*/ | |
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI1) == (RCC_PERIPHCLK_SAI1)) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_SAI1CLKSOURCE(PeriphClkInit->Sai1ClockSelection)); | |
/* Configure SAI1 Clock source */ | |
__HAL_RCC_SAI1_CONFIG(PeriphClkInit->Sai1ClockSelection); | |
/* Enable the PLLI2S when it's used as clock source for SAI */ | |
if(PeriphClkInit->Sai1ClockSelection == RCC_SAI1CLKSOURCE_PLLI2S) | |
{ | |
plli2sused = 1; | |
} | |
/* Enable the PLLSAI when it's used as clock source for SAI */ | |
if(PeriphClkInit->Sai1ClockSelection == RCC_SAI1CLKSOURCE_PLLSAI) | |
{ | |
pllsaiused = 1; | |
} | |
} | |
/*------------------------------------ SAI2 configuration --------------------------------------*/ | |
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI2) == (RCC_PERIPHCLK_SAI2)) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_SAI2CLKSOURCE(PeriphClkInit->Sai2ClockSelection)); | |
/* Configure SAI2 Clock source */ | |
__HAL_RCC_SAI2_CONFIG(PeriphClkInit->Sai2ClockSelection); | |
/* Enable the PLLI2S when it's used as clock source for SAI */ | |
if(PeriphClkInit->Sai2ClockSelection == RCC_SAI2CLKSOURCE_PLLI2S) | |
{ | |
plli2sused = 1; | |
} | |
/* Enable the PLLSAI when it's used as clock source for SAI */ | |
if(PeriphClkInit->Sai2ClockSelection == RCC_SAI2CLKSOURCE_PLLSAI) | |
{ | |
pllsaiused = 1; | |
} | |
} | |
/*-------------------------------------- SPDIF-RX Configuration -----------------------------------*/ | |
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SPDIFRX) == RCC_PERIPHCLK_SPDIFRX) | |
{ | |
plli2sused = 1; | |
} | |
/*------------------------------------ RTC configuration --------------------------------------*/ | |
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_RTC) == (RCC_PERIPHCLK_RTC)) | |
{ | |
/* Check for RTC Parameters used to output RTCCLK */ | |
assert_param(IS_RCC_RTCCLKSOURCE(PeriphClkInit->RTCClockSelection)); | |
/* Enable Power Clock*/ | |
__HAL_RCC_PWR_CLK_ENABLE(); | |
/* Enable write access to Backup domain */ | |
PWR->CR1 |= PWR_CR1_DBP; | |
/* Get Start Tick*/ | |
tickstart = HAL_GetTick(); | |
/* Wait for Backup domain Write protection disable */ | |
while((PWR->CR1 & PWR_CR1_DBP) == RESET) | |
{ | |
if((HAL_GetTick() - tickstart) > RCC_DBP_TIMEOUT_VALUE) | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
/* Reset the Backup domain only if the RTC Clock source selection is modified */ | |
tmpreg0 = (RCC->BDCR & RCC_BDCR_RTCSEL); | |
if((tmpreg0 != 0x00000000U) && (tmpreg0 != (PeriphClkInit->RTCClockSelection & RCC_BDCR_RTCSEL))) | |
{ | |
/* Store the content of BDCR register before the reset of Backup Domain */ | |
tmpreg0 = (RCC->BDCR & ~(RCC_BDCR_RTCSEL)); | |
/* RTC Clock selection can be changed only if the Backup Domain is reset */ | |
__HAL_RCC_BACKUPRESET_FORCE(); | |
__HAL_RCC_BACKUPRESET_RELEASE(); | |
/* Restore the Content of BDCR register */ | |
RCC->BDCR = tmpreg0; | |
/* Wait for LSE reactivation if LSE was enable prior to Backup Domain reset */ | |
if (HAL_IS_BIT_SET(RCC->BDCR, RCC_BDCR_LSEON)) | |
{ | |
/* Get Start Tick*/ | |
tickstart = HAL_GetTick(); | |
/* Wait till LSE is ready */ | |
while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == RESET) | |
{ | |
if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
} | |
__HAL_RCC_RTC_CONFIG(PeriphClkInit->RTCClockSelection); | |
} | |
/*------------------------------------ TIM configuration --------------------------------------*/ | |
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_TIM) == (RCC_PERIPHCLK_TIM)) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_TIMPRES(PeriphClkInit->TIMPresSelection)); | |
/* Configure Timer Prescaler */ | |
__HAL_RCC_TIMCLKPRESCALER(PeriphClkInit->TIMPresSelection); | |
} | |
/*-------------------------------------- I2C1 Configuration -----------------------------------*/ | |
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2C1) == RCC_PERIPHCLK_I2C1) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_I2C1CLKSOURCE(PeriphClkInit->I2c1ClockSelection)); | |
/* Configure the I2C1 clock source */ | |
__HAL_RCC_I2C1_CONFIG(PeriphClkInit->I2c1ClockSelection); | |
} | |
/*-------------------------------------- I2C2 Configuration -----------------------------------*/ | |
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2C2) == RCC_PERIPHCLK_I2C2) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_I2C2CLKSOURCE(PeriphClkInit->I2c2ClockSelection)); | |
/* Configure the I2C2 clock source */ | |
__HAL_RCC_I2C2_CONFIG(PeriphClkInit->I2c2ClockSelection); | |
} | |
/*-------------------------------------- I2C3 Configuration -----------------------------------*/ | |
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2C3) == RCC_PERIPHCLK_I2C3) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_I2C3CLKSOURCE(PeriphClkInit->I2c3ClockSelection)); | |
/* Configure the I2C3 clock source */ | |
__HAL_RCC_I2C3_CONFIG(PeriphClkInit->I2c3ClockSelection); | |
} | |
/*-------------------------------------- I2C4 Configuration -----------------------------------*/ | |
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2C4) == RCC_PERIPHCLK_I2C4) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_I2C4CLKSOURCE(PeriphClkInit->I2c4ClockSelection)); | |
/* Configure the I2C4 clock source */ | |
__HAL_RCC_I2C4_CONFIG(PeriphClkInit->I2c4ClockSelection); | |
} | |
/*-------------------------------------- USART1 Configuration -----------------------------------*/ | |
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_USART1) == RCC_PERIPHCLK_USART1) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_USART1CLKSOURCE(PeriphClkInit->Usart1ClockSelection)); | |
/* Configure the USART1 clock source */ | |
__HAL_RCC_USART1_CONFIG(PeriphClkInit->Usart1ClockSelection); | |
} | |
/*-------------------------------------- USART2 Configuration -----------------------------------*/ | |
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_USART2) == RCC_PERIPHCLK_USART2) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_USART2CLKSOURCE(PeriphClkInit->Usart2ClockSelection)); | |
/* Configure the USART2 clock source */ | |
__HAL_RCC_USART2_CONFIG(PeriphClkInit->Usart2ClockSelection); | |
} | |
/*-------------------------------------- USART3 Configuration -----------------------------------*/ | |
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_USART3) == RCC_PERIPHCLK_USART3) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_USART3CLKSOURCE(PeriphClkInit->Usart3ClockSelection)); | |
/* Configure the USART3 clock source */ | |
__HAL_RCC_USART3_CONFIG(PeriphClkInit->Usart3ClockSelection); | |
} | |
/*-------------------------------------- UART4 Configuration -----------------------------------*/ | |
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_UART4) == RCC_PERIPHCLK_UART4) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_UART4CLKSOURCE(PeriphClkInit->Uart4ClockSelection)); | |
/* Configure the UART4 clock source */ | |
__HAL_RCC_UART4_CONFIG(PeriphClkInit->Uart4ClockSelection); | |
} | |
/*-------------------------------------- UART5 Configuration -----------------------------------*/ | |
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_UART5) == RCC_PERIPHCLK_UART5) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_UART5CLKSOURCE(PeriphClkInit->Uart5ClockSelection)); | |
/* Configure the UART5 clock source */ | |
__HAL_RCC_UART5_CONFIG(PeriphClkInit->Uart5ClockSelection); | |
} | |
/*-------------------------------------- USART6 Configuration -----------------------------------*/ | |
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_USART6) == RCC_PERIPHCLK_USART6) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_USART6CLKSOURCE(PeriphClkInit->Usart6ClockSelection)); | |
/* Configure the USART6 clock source */ | |
__HAL_RCC_USART6_CONFIG(PeriphClkInit->Usart6ClockSelection); | |
} | |
/*-------------------------------------- UART7 Configuration -----------------------------------*/ | |
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_UART7) == RCC_PERIPHCLK_UART7) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_UART7CLKSOURCE(PeriphClkInit->Uart7ClockSelection)); | |
/* Configure the UART7 clock source */ | |
__HAL_RCC_UART7_CONFIG(PeriphClkInit->Uart7ClockSelection); | |
} | |
/*-------------------------------------- UART8 Configuration -----------------------------------*/ | |
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_UART8) == RCC_PERIPHCLK_UART8) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_UART8CLKSOURCE(PeriphClkInit->Uart8ClockSelection)); | |
/* Configure the UART8 clock source */ | |
__HAL_RCC_UART8_CONFIG(PeriphClkInit->Uart8ClockSelection); | |
} | |
/*--------------------------------------- CEC Configuration -----------------------------------*/ | |
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_CEC) == RCC_PERIPHCLK_CEC) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_CECCLKSOURCE(PeriphClkInit->CecClockSelection)); | |
/* Configure the CEC clock source */ | |
__HAL_RCC_CEC_CONFIG(PeriphClkInit->CecClockSelection); | |
} | |
/*-------------------------------------- CK48 Configuration -----------------------------------*/ | |
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_CLK48) == RCC_PERIPHCLK_CLK48) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_CLK48SOURCE(PeriphClkInit->Clk48ClockSelection)); | |
/* Configure the CLK48 source */ | |
__HAL_RCC_CLK48_CONFIG(PeriphClkInit->Clk48ClockSelection); | |
/* Enable the PLLSAI when it's used as clock source for CK48 */ | |
if(PeriphClkInit->Clk48ClockSelection == RCC_CLK48SOURCE_PLLSAIP) | |
{ | |
pllsaiused = 1; | |
} | |
} | |
/*-------------------------------------- LTDC Configuration -----------------------------------*/ | |
#if defined(STM32F746xx) || defined(STM32F756xx) || defined (STM32F767xx) || defined (STM32F769xx) || defined (STM32F777xx) || defined (STM32F779xx) | |
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_LTDC) == RCC_PERIPHCLK_LTDC) | |
{ | |
pllsaiused = 1; | |
} | |
#endif /* STM32F746xx || STM32F756xx || STM32F767xx || STM32F769xx || STM32F777xx || STM32F779xx */ | |
/*-------------------------------------- LPTIM1 Configuration -----------------------------------*/ | |
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_LPTIM1) == RCC_PERIPHCLK_LPTIM1) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_LPTIM1CLK(PeriphClkInit->Lptim1ClockSelection)); | |
/* Configure the LTPIM1 clock source */ | |
__HAL_RCC_LPTIM1_CONFIG(PeriphClkInit->Lptim1ClockSelection); | |
} | |
/*------------------------------------- SDMMC1 Configuration ------------------------------------*/ | |
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SDMMC1) == RCC_PERIPHCLK_SDMMC1) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_SDMMC1CLKSOURCE(PeriphClkInit->Sdmmc1ClockSelection)); | |
/* Configure the SDMMC1 clock source */ | |
__HAL_RCC_SDMMC1_CONFIG(PeriphClkInit->Sdmmc1ClockSelection); | |
} | |
#if defined (STM32F765xx) || defined (STM32F767xx) || defined (STM32F769xx) || defined (STM32F777xx) || defined (STM32F779xx) | |
/*------------------------------------- SDMMC2 Configuration ------------------------------------*/ | |
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SDMMC2) == RCC_PERIPHCLK_SDMMC2) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_SDMMC2CLKSOURCE(PeriphClkInit->Sdmmc2ClockSelection)); | |
/* Configure the SDMMC2 clock source */ | |
__HAL_RCC_SDMMC2_CONFIG(PeriphClkInit->Sdmmc2ClockSelection); | |
} | |
/*------------------------------------- DFSDM1 Configuration -------------------------------------*/ | |
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_DFSDM1) == RCC_PERIPHCLK_DFSDM1) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_DFSDM1CLKSOURCE(PeriphClkInit->Dfsdm1ClockSelection)); | |
/* Configure the DFSDM1 interface clock source */ | |
__HAL_RCC_DFSDM1_CONFIG(PeriphClkInit->Dfsdm1ClockSelection); | |
} | |
/*------------------------------------- DFSDM AUDIO Configuration -------------------------------------*/ | |
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_DFSDM1_AUDIO) == RCC_PERIPHCLK_DFSDM1_AUDIO) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_DFSDM1AUDIOCLKSOURCE(PeriphClkInit->Dfsdm1AudioClockSelection)); | |
/* Configure the DFSDM interface clock source */ | |
__HAL_RCC_DFSDM1AUDIO_CONFIG(PeriphClkInit->Dfsdm1AudioClockSelection); | |
} | |
#endif /* STM32F767xx || STM32F769xx || STM32F777xx || STM32F779xx */ | |
/*-------------------------------------- PLLI2S Configuration ---------------------------------*/ | |
/* PLLI2S is configured when a peripheral will use it as source clock : SAI1, SAI2, I2S or SPDIF-RX */ | |
if((plli2sused == 1) || (PeriphClkInit->PeriphClockSelection == RCC_PERIPHCLK_PLLI2S)) | |
{ | |
/* Disable the PLLI2S */ | |
__HAL_RCC_PLLI2S_DISABLE(); | |
/* Get Start Tick*/ | |
tickstart = HAL_GetTick(); | |
/* Wait till PLLI2S is disabled */ | |
while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) != RESET) | |
{ | |
if((HAL_GetTick() - tickstart) > PLLI2S_TIMEOUT_VALUE) | |
{ | |
/* return in case of Timeout detected */ | |
return HAL_TIMEOUT; | |
} | |
} | |
/* check for common PLLI2S Parameters */ | |
assert_param(IS_RCC_PLLI2SN_VALUE(PeriphClkInit->PLLI2S.PLLI2SN)); | |
/*----------------- In Case of PLLI2S is selected as source clock for I2S -------------------*/ | |
if(((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S) == RCC_PERIPHCLK_I2S) && (PeriphClkInit->I2sClockSelection == RCC_I2SCLKSOURCE_PLLI2S))) | |
{ | |
/* check for Parameters */ | |
assert_param(IS_RCC_PLLI2SR_VALUE(PeriphClkInit->PLLI2S.PLLI2SR)); | |
/* Read PLLI2SP and PLLI2SQ value from PLLI2SCFGR register (this value is not needed for I2S configuration) */ | |
tmpreg0 = ((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SP) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SP)); | |
tmpreg1 = ((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SQ) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SQ)); | |
/* Configure the PLLI2S division factors */ | |
/* PLLI2S_VCO = f(VCO clock) = f(PLLI2S clock input) x (PLLI2SN/PLLM) */ | |
/* I2SCLK = f(PLLI2S clock output) = f(VCO clock) / PLLI2SR */ | |
__HAL_RCC_PLLI2S_CONFIG(PeriphClkInit->PLLI2S.PLLI2SN , tmpreg0, tmpreg1, PeriphClkInit->PLLI2S.PLLI2SR); | |
} | |
/*----------------- In Case of PLLI2S is selected as source clock for SAI -------------------*/ | |
if(((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI1) == RCC_PERIPHCLK_SAI1) && (PeriphClkInit->Sai1ClockSelection == RCC_SAI1CLKSOURCE_PLLI2S)) || | |
((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI2) == RCC_PERIPHCLK_SAI2) && (PeriphClkInit->Sai2ClockSelection == RCC_SAI2CLKSOURCE_PLLI2S))) | |
{ | |
/* Check for PLLI2S Parameters */ | |
assert_param(IS_RCC_PLLI2SQ_VALUE(PeriphClkInit->PLLI2S.PLLI2SQ)); | |
/* Check for PLLI2S/DIVQ parameters */ | |
assert_param(IS_RCC_PLLI2S_DIVQ_VALUE(PeriphClkInit->PLLI2SDivQ)); | |
/* Read PLLI2SP and PLLI2SR values from PLLI2SCFGR register (this value is not needed for SAI configuration) */ | |
tmpreg0 = ((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SP) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SP)); | |
tmpreg1 = ((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SR) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SR)); | |
/* Configure the PLLI2S division factors */ | |
/* PLLI2S_VCO Input = PLL_SOURCE/PLLM */ | |
/* PLLI2S_VCO Output = PLLI2S_VCO Input * PLLI2SN */ | |
/* SAI_CLK(first level) = PLLI2S_VCO Output/PLLI2SQ */ | |
__HAL_RCC_PLLI2S_CONFIG(PeriphClkInit->PLLI2S.PLLI2SN, tmpreg0, PeriphClkInit->PLLI2S.PLLI2SQ, tmpreg1); | |
/* SAI_CLK_x = SAI_CLK(first level)/PLLI2SDIVQ */ | |
__HAL_RCC_PLLI2S_PLLSAICLKDIVQ_CONFIG(PeriphClkInit->PLLI2SDivQ); | |
} | |
/*----------------- In Case of PLLI2S is selected as source clock for SPDIF-RX -------------------*/ | |
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SPDIFRX) == RCC_PERIPHCLK_SPDIFRX) | |
{ | |
/* check for Parameters */ | |
assert_param(IS_RCC_PLLI2SP_VALUE(PeriphClkInit->PLLI2S.PLLI2SP)); | |
/* Read PLLI2SR value from PLLI2SCFGR register (this value is not needed for SPDIF-RX configuration) */ | |
tmpreg0 = ((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SQ) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SQ)); | |
tmpreg1 = ((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SR) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SR)); | |
/* Configure the PLLI2S division factors */ | |
/* PLLI2S_VCO = f(VCO clock) = f(PLLI2S clock input) x (PLLI2SN/PLLM) */ | |
/* SPDIFCLK = f(PLLI2S clock output) = f(VCO clock) / PLLI2SP */ | |
__HAL_RCC_PLLI2S_CONFIG(PeriphClkInit->PLLI2S.PLLI2SN , PeriphClkInit->PLLI2S.PLLI2SP, tmpreg0, tmpreg1); | |
} | |
/*----------------- In Case of PLLI2S is just selected -----------------*/ | |
if((PeriphClkInit->PeriphClockSelection & RCC_PERIPHCLK_PLLI2S) == RCC_PERIPHCLK_PLLI2S) | |
{ | |
/* Check for Parameters */ | |
assert_param(IS_RCC_PLLI2SP_VALUE(PeriphClkInit->PLLI2S.PLLI2SP)); | |
assert_param(IS_RCC_PLLI2SR_VALUE(PeriphClkInit->PLLI2S.PLLI2SR)); | |
assert_param(IS_RCC_PLLI2SQ_VALUE(PeriphClkInit->PLLI2S.PLLI2SQ)); | |
/* Configure the PLLI2S division factors */ | |
/* PLLI2S_VCO = f(VCO clock) = f(PLLI2S clock input) x (PLLI2SN/PLLI2SM) */ | |
/* SPDIFRXCLK = f(PLLI2S clock output) = f(VCO clock) / PLLI2SP */ | |
__HAL_RCC_PLLI2S_CONFIG(PeriphClkInit->PLLI2S.PLLI2SN , PeriphClkInit->PLLI2S.PLLI2SP, PeriphClkInit->PLLI2S.PLLI2SQ, PeriphClkInit->PLLI2S.PLLI2SR); | |
} | |
/* Enable the PLLI2S */ | |
__HAL_RCC_PLLI2S_ENABLE(); | |
/* Get Start Tick*/ | |
tickstart = HAL_GetTick(); | |
/* Wait till PLLI2S is ready */ | |
while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) == RESET) | |
{ | |
if((HAL_GetTick() - tickstart) > PLLI2S_TIMEOUT_VALUE) | |
{ | |
/* return in case of Timeout detected */ | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
/*-------------------------------------- PLLSAI Configuration ---------------------------------*/ | |
/* PLLSAI is configured when a peripheral will use it as source clock : SAI1, SAI2, LTDC or CK48 */ | |
if(pllsaiused == 1) | |
{ | |
/* Disable PLLSAI Clock */ | |
__HAL_RCC_PLLSAI_DISABLE(); | |
/* Get Start Tick*/ | |
tickstart = HAL_GetTick(); | |
/* Wait till PLLSAI is disabled */ | |
while(__HAL_RCC_PLLSAI_GET_FLAG() != RESET) | |
{ | |
if((HAL_GetTick() - tickstart) > PLLSAI_TIMEOUT_VALUE) | |
{ | |
/* return in case of Timeout detected */ | |
return HAL_TIMEOUT; | |
} | |
} | |
/* Check the PLLSAI division factors */ | |
assert_param(IS_RCC_PLLSAIN_VALUE(PeriphClkInit->PLLSAI.PLLSAIN)); | |
/*----------------- In Case of PLLSAI is selected as source clock for SAI -------------------*/ | |
if(((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI1) == RCC_PERIPHCLK_SAI1) && (PeriphClkInit->Sai1ClockSelection == RCC_SAI1CLKSOURCE_PLLSAI)) ||\ | |
((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI2) == RCC_PERIPHCLK_SAI2) && (PeriphClkInit->Sai2ClockSelection == RCC_SAI2CLKSOURCE_PLLSAI))) | |
{ | |
/* check for PLLSAIQ Parameter */ | |
assert_param(IS_RCC_PLLSAIQ_VALUE(PeriphClkInit->PLLSAI.PLLSAIQ)); | |
/* check for PLLSAI/DIVQ Parameter */ | |
assert_param(IS_RCC_PLLSAI_DIVQ_VALUE(PeriphClkInit->PLLSAIDivQ)); | |
/* Read PLLSAIP value from PLLSAICFGR register (this value is not needed for SAI configuration) */ | |
tmpreg0 = ((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIP) >> POSITION_VAL(RCC_PLLSAICFGR_PLLSAIP)); | |
tmpreg1 = ((RCC->PLLSAICFGR & RCC_PLLI2SCFGR_PLLI2SR) >> POSITION_VAL(RCC_PLLSAICFGR_PLLSAIR)); | |
/* PLLSAI_VCO Input = PLL_SOURCE/PLLM */ | |
/* PLLSAI_VCO Output = PLLSAI_VCO Input * PLLSAIN */ | |
/* SAI_CLK(first level) = PLLSAI_VCO Output/PLLSAIQ */ | |
__HAL_RCC_PLLSAI_CONFIG(PeriphClkInit->PLLSAI.PLLSAIN , tmpreg0, PeriphClkInit->PLLSAI.PLLSAIQ, tmpreg1); | |
/* SAI_CLK_x = SAI_CLK(first level)/PLLSAIDIVQ */ | |
__HAL_RCC_PLLSAI_PLLSAICLKDIVQ_CONFIG(PeriphClkInit->PLLSAIDivQ); | |
} | |
/*----------------- In Case of PLLSAI is selected as source clock for CLK48 -------------------*/ | |
/* In Case of PLLI2S is selected as source clock for CK48 */ | |
if((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_CLK48) == RCC_PERIPHCLK_CLK48) && (PeriphClkInit->Clk48ClockSelection == RCC_CLK48SOURCE_PLLSAIP)) | |
{ | |
/* check for Parameters */ | |
assert_param(IS_RCC_PLLSAIP_VALUE(PeriphClkInit->PLLSAI.PLLSAIP)); | |
/* Read PLLSAIQ and PLLSAIR value from PLLSAICFGR register (this value is not needed for CK48 configuration) */ | |
tmpreg0 = ((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIQ) >> POSITION_VAL(RCC_PLLSAICFGR_PLLSAIQ)); | |
tmpreg1 = ((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIR) >> POSITION_VAL(RCC_PLLSAICFGR_PLLSAIR)); | |
/* Configure the PLLSAI division factors */ | |
/* PLLSAI_VCO = f(VCO clock) = f(PLLSAI clock input) x (PLLI2SN/PLLM) */ | |
/* 48CLK = f(PLLSAI clock output) = f(VCO clock) / PLLSAIP */ | |
__HAL_RCC_PLLSAI_CONFIG(PeriphClkInit->PLLSAI.PLLSAIN , PeriphClkInit->PLLSAI.PLLSAIP, tmpreg0, tmpreg1); | |
} | |
#if defined(STM32F746xx) || defined(STM32F756xx) || defined (STM32F767xx) || defined (STM32F769xx) || defined (STM32F777xx) || defined (STM32F779xx) | |
/*---------------------------- LTDC configuration -------------------------------*/ | |
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_LTDC) == (RCC_PERIPHCLK_LTDC)) | |
{ | |
assert_param(IS_RCC_PLLSAIR_VALUE(PeriphClkInit->PLLSAI.PLLSAIR)); | |
assert_param(IS_RCC_PLLSAI_DIVR_VALUE(PeriphClkInit->PLLSAIDivR)); | |
/* Read PLLSAIP and PLLSAIQ value from PLLSAICFGR register (these value are not needed for LTDC configuration) */ | |
tmpreg0 = ((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIQ) >> POSITION_VAL(RCC_PLLSAICFGR_PLLSAIQ)); | |
tmpreg1 = ((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIP) >> POSITION_VAL(RCC_PLLSAICFGR_PLLSAIP)); | |
/* PLLSAI_VCO Input = PLL_SOURCE/PLLM */ | |
/* PLLSAI_VCO Output = PLLSAI_VCO Input * PLLSAIN */ | |
/* LTDC_CLK(first level) = PLLSAI_VCO Output/PLLSAIR */ | |
__HAL_RCC_PLLSAI_CONFIG(PeriphClkInit->PLLSAI.PLLSAIN , tmpreg1, tmpreg0, PeriphClkInit->PLLSAI.PLLSAIR); | |
/* LTDC_CLK = LTDC_CLK(first level)/PLLSAIDIVR */ | |
__HAL_RCC_PLLSAI_PLLSAICLKDIVR_CONFIG(PeriphClkInit->PLLSAIDivR); | |
} | |
#endif /* STM32F746xx || STM32F756xx || STM32F767xx || STM32F769xx || STM32F777xx || STM32F779xx */ | |
/* Enable PLLSAI Clock */ | |
__HAL_RCC_PLLSAI_ENABLE(); | |
/* Get Start Tick*/ | |
tickstart = HAL_GetTick(); | |
/* Wait till PLLSAI is ready */ | |
while(__HAL_RCC_PLLSAI_GET_FLAG() == RESET) | |
{ | |
if((HAL_GetTick() - tickstart) > PLLSAI_TIMEOUT_VALUE) | |
{ | |
/* return in case of Timeout detected */ | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
return HAL_OK; | |
} | |
/** | |
* @brief Get the RCC_PeriphCLKInitTypeDef according to the internal | |
* RCC configuration registers. | |
* @param PeriphClkInit: pointer to the configured RCC_PeriphCLKInitTypeDef structure | |
* @retval None | |
*/ | |
void HAL_RCCEx_GetPeriphCLKConfig(RCC_PeriphCLKInitTypeDef *PeriphClkInit) | |
{ | |
uint32_t tempreg = 0; | |
/* Set all possible values for the extended clock type parameter------------*/ | |
#if defined (STM32F765xx) || defined (STM32F767xx) || defined (STM32F769xx) || defined (STM32F777xx) || defined (STM32F779xx) | |
PeriphClkInit->PeriphClockSelection = RCC_PERIPHCLK_I2S | RCC_PERIPHCLK_LPTIM1 |\ | |
RCC_PERIPHCLK_SAI1 | RCC_PERIPHCLK_SAI2 |\ | |
RCC_PERIPHCLK_TIM | RCC_PERIPHCLK_RTC |\ | |
RCC_PERIPHCLK_CEC | RCC_PERIPHCLK_I2C4 |\ | |
RCC_PERIPHCLK_I2C1 | RCC_PERIPHCLK_I2C2 |\ | |
RCC_PERIPHCLK_I2C3 | RCC_PERIPHCLK_USART1 |\ | |
RCC_PERIPHCLK_USART2 | RCC_PERIPHCLK_USART3 |\ | |
RCC_PERIPHCLK_UART4 | RCC_PERIPHCLK_UART5 |\ | |
RCC_PERIPHCLK_USART6 | RCC_PERIPHCLK_UART7 |\ | |
RCC_PERIPHCLK_UART8 | RCC_PERIPHCLK_SDMMC1 |\ | |
RCC_PERIPHCLK_CLK48 | RCC_PERIPHCLK_SDMMC2 |\ | |
RCC_PERIPHCLK_DFSDM1 | RCC_PERIPHCLK_DFSDM1_AUDIO; | |
#else | |
PeriphClkInit->PeriphClockSelection = RCC_PERIPHCLK_I2S | RCC_PERIPHCLK_LPTIM1 |\ | |
RCC_PERIPHCLK_SAI1 | RCC_PERIPHCLK_SAI2 |\ | |
RCC_PERIPHCLK_TIM | RCC_PERIPHCLK_RTC |\ | |
RCC_PERIPHCLK_CEC | RCC_PERIPHCLK_I2C4 |\ | |
RCC_PERIPHCLK_I2C1 | RCC_PERIPHCLK_I2C2 |\ | |
RCC_PERIPHCLK_I2C3 | RCC_PERIPHCLK_USART1 |\ | |
RCC_PERIPHCLK_USART2 | RCC_PERIPHCLK_USART3 |\ | |
RCC_PERIPHCLK_UART4 | RCC_PERIPHCLK_UART5 |\ | |
RCC_PERIPHCLK_USART6 | RCC_PERIPHCLK_UART7 |\ | |
RCC_PERIPHCLK_UART8 | RCC_PERIPHCLK_SDMMC1 |\ | |
RCC_PERIPHCLK_CLK48; | |
#endif /* STM32F767xx || STM32F769xx || STM32F777xx || STM32F779xx */ | |
/* Get the PLLI2S Clock configuration -----------------------------------------------*/ | |
PeriphClkInit->PLLI2S.PLLI2SN = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SN) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SN)); | |
PeriphClkInit->PLLI2S.PLLI2SP = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SP) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SP)); | |
PeriphClkInit->PLLI2S.PLLI2SQ = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SQ) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SQ)); | |
PeriphClkInit->PLLI2S.PLLI2SR = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SR) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SR)); | |
/* Get the PLLSAI Clock configuration -----------------------------------------------*/ | |
PeriphClkInit->PLLSAI.PLLSAIN = (uint32_t)((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIN) >> POSITION_VAL(RCC_PLLSAICFGR_PLLSAIN)); | |
PeriphClkInit->PLLSAI.PLLSAIP = (uint32_t)((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIP) >> POSITION_VAL(RCC_PLLSAICFGR_PLLSAIP)); | |
PeriphClkInit->PLLSAI.PLLSAIQ = (uint32_t)((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIQ) >> POSITION_VAL(RCC_PLLSAICFGR_PLLSAIQ)); | |
PeriphClkInit->PLLSAI.PLLSAIR = (uint32_t)((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIR) >> POSITION_VAL(RCC_PLLSAICFGR_PLLSAIR)); | |
/* Get the PLLSAI/PLLI2S division factors -------------------------------------------*/ | |
PeriphClkInit->PLLI2SDivQ = (uint32_t)((RCC->DCKCFGR1 & RCC_DCKCFGR1_PLLI2SDIVQ) >> POSITION_VAL(RCC_DCKCFGR1_PLLI2SDIVQ)); | |
PeriphClkInit->PLLSAIDivQ = (uint32_t)((RCC->DCKCFGR1 & RCC_DCKCFGR1_PLLSAIDIVQ) >> POSITION_VAL(RCC_DCKCFGR1_PLLSAIDIVQ)); | |
PeriphClkInit->PLLSAIDivR = (uint32_t)((RCC->DCKCFGR1 & RCC_DCKCFGR1_PLLSAIDIVR) >> POSITION_VAL(RCC_DCKCFGR1_PLLSAIDIVR)); | |
/* Get the SAI1 clock configuration ----------------------------------------------*/ | |
PeriphClkInit->Sai1ClockSelection = __HAL_RCC_GET_SAI1_SOURCE(); | |
/* Get the SAI2 clock configuration ----------------------------------------------*/ | |
PeriphClkInit->Sai2ClockSelection = __HAL_RCC_GET_SAI2_SOURCE(); | |
/* Get the I2S clock configuration ------------------------------------------*/ | |
PeriphClkInit->I2sClockSelection = __HAL_RCC_GET_I2SCLKSOURCE(); | |
/* Get the I2C1 clock configuration ------------------------------------------*/ | |
PeriphClkInit->I2c1ClockSelection = __HAL_RCC_GET_I2C1_SOURCE(); | |
/* Get the I2C2 clock configuration ------------------------------------------*/ | |
PeriphClkInit->I2c2ClockSelection = __HAL_RCC_GET_I2C2_SOURCE(); | |
/* Get the I2C3 clock configuration ------------------------------------------*/ | |
PeriphClkInit->I2c3ClockSelection = __HAL_RCC_GET_I2C3_SOURCE(); | |
/* Get the I2C4 clock configuration ------------------------------------------*/ | |
PeriphClkInit->I2c4ClockSelection = __HAL_RCC_GET_I2C4_SOURCE(); | |
/* Get the USART1 clock configuration ------------------------------------------*/ | |
PeriphClkInit->Usart1ClockSelection = __HAL_RCC_GET_USART1_SOURCE(); | |
/* Get the USART2 clock configuration ------------------------------------------*/ | |
PeriphClkInit->Usart2ClockSelection = __HAL_RCC_GET_USART2_SOURCE(); | |
/* Get the USART3 clock configuration ------------------------------------------*/ | |
PeriphClkInit->Usart3ClockSelection = __HAL_RCC_GET_USART3_SOURCE(); | |
/* Get the UART4 clock configuration ------------------------------------------*/ | |
PeriphClkInit->Uart4ClockSelection = __HAL_RCC_GET_UART4_SOURCE(); | |
/* Get the UART5 clock configuration ------------------------------------------*/ | |
PeriphClkInit->Uart5ClockSelection = __HAL_RCC_GET_UART5_SOURCE(); | |
/* Get the USART6 clock configuration ------------------------------------------*/ | |
PeriphClkInit->Usart6ClockSelection = __HAL_RCC_GET_USART6_SOURCE(); | |
/* Get the UART7 clock configuration ------------------------------------------*/ | |
PeriphClkInit->Uart7ClockSelection = __HAL_RCC_GET_UART7_SOURCE(); | |
/* Get the UART8 clock configuration ------------------------------------------*/ | |
PeriphClkInit->Uart8ClockSelection = __HAL_RCC_GET_UART8_SOURCE(); | |
/* Get the LPTIM1 clock configuration ------------------------------------------*/ | |
PeriphClkInit->Lptim1ClockSelection = __HAL_RCC_GET_LPTIM1_SOURCE(); | |
/* Get the CEC clock configuration -----------------------------------------------*/ | |
PeriphClkInit->CecClockSelection = __HAL_RCC_GET_CEC_SOURCE(); | |
/* Get the CK48 clock configuration -----------------------------------------------*/ | |
PeriphClkInit->Clk48ClockSelection = __HAL_RCC_GET_CLK48_SOURCE(); | |
/* Get the SDMMC1 clock configuration -----------------------------------------------*/ | |
PeriphClkInit->Sdmmc1ClockSelection = __HAL_RCC_GET_SDMMC1_SOURCE(); | |
#if defined (STM32F765xx) || defined (STM32F767xx) || defined (STM32F769xx) || defined (STM32F777xx) || defined (STM32F779xx) | |
/* Get the SDMMC2 clock configuration -----------------------------------------------*/ | |
PeriphClkInit->Sdmmc2ClockSelection = __HAL_RCC_GET_SDMMC2_SOURCE(); | |
/* Get the DFSDM clock configuration -----------------------------------------------*/ | |
PeriphClkInit->Dfsdm1ClockSelection = __HAL_RCC_GET_DFSDM1_SOURCE(); | |
/* Get the DFSDM AUDIO clock configuration -----------------------------------------------*/ | |
PeriphClkInit->Dfsdm1AudioClockSelection = __HAL_RCC_GET_DFSDM1AUDIO_SOURCE(); | |
#endif /* STM32F767xx || STM32F769xx || STM32F777xx || STM32F779xx */ | |
/* Get the RTC Clock configuration -----------------------------------------------*/ | |
tempreg = (RCC->CFGR & RCC_CFGR_RTCPRE); | |
PeriphClkInit->RTCClockSelection = (uint32_t)((tempreg) | (RCC->BDCR & RCC_BDCR_RTCSEL)); | |
/* Get the TIM Prescaler configuration --------------------------------------------*/ | |
if ((RCC->DCKCFGR1 & RCC_DCKCFGR1_TIMPRE) == RESET) | |
{ | |
PeriphClkInit->TIMPresSelection = RCC_TIMPRES_DESACTIVATED; | |
} | |
else | |
{ | |
PeriphClkInit->TIMPresSelection = RCC_TIMPRES_ACTIVATED; | |
} | |
} | |
/** | |
* @brief Return the peripheral clock frequency for a given peripheral(SAI..) | |
* @note Return 0 if peripheral clock identifier not managed by this API | |
* @param PeriphClk: Peripheral clock identifier | |
* This parameter can be one of the following values: | |
* @arg RCC_PERIPHCLK_SAI1: SAI1 peripheral clock | |
* @arg RCC_PERIPHCLK_SAI2: SAI2 peripheral clock | |
* @retval Frequency in KHz | |
*/ | |
uint32_t HAL_RCCEx_GetPeriphCLKFreq(uint32_t PeriphClk) | |
{ | |
uint32_t tmpreg = 0; | |
/* This variable is used to store the SAI clock frequency (value in Hz) */ | |
uint32_t frequency = 0; | |
/* This variable is used to store the VCO Input (value in Hz) */ | |
uint32_t vcoinput = 0; | |
/* This variable is used to store the SAI clock source */ | |
uint32_t saiclocksource = 0; | |
if (PeriphClk == RCC_PERIPHCLK_SAI1) | |
{ | |
saiclocksource = RCC->DCKCFGR1; | |
saiclocksource &= RCC_DCKCFGR1_SAI1SEL; | |
switch (saiclocksource) | |
{ | |
case 0: /* PLLSAI is the clock source for SAI1 */ | |
{ | |
/* Configure the PLLSAI division factor */ | |
/* PLLSAI_VCO Input = PLL_SOURCE/PLLM */ | |
if((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSI) | |
{ | |
/* In Case the PLL Source is HSI (Internal Clock) */ | |
vcoinput = (HSI_VALUE / (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM)); | |
} | |
else | |
{ | |
/* In Case the PLL Source is HSE (External Clock) */ | |
vcoinput = ((HSE_VALUE / (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM))); | |
} | |
/* PLLSAI_VCO Output = PLLSAI_VCO Input * PLLSAIN */ | |
/* SAI_CLK(first level) = PLLSAI_VCO Output/PLLSAIQ */ | |
tmpreg = (RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIQ) >> 24; | |
frequency = (vcoinput * ((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIN) >> 6))/(tmpreg); | |
/* SAI_CLK_x = SAI_CLK(first level)/PLLSAIDIVQ */ | |
tmpreg = (((RCC->DCKCFGR1 & RCC_DCKCFGR1_PLLSAIDIVQ) >> 8) + 1); | |
frequency = frequency/(tmpreg); | |
break; | |
} | |
case RCC_DCKCFGR1_SAI1SEL_0: /* PLLI2S is the clock source for SAI1 */ | |
{ | |
/* Configure the PLLI2S division factor */ | |
/* PLLI2S_VCO Input = PLL_SOURCE/PLLM */ | |
if((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSI) | |
{ | |
/* In Case the PLL Source is HSI (Internal Clock) */ | |
vcoinput = (HSI_VALUE / (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM)); | |
} | |
else | |
{ | |
/* In Case the PLL Source is HSE (External Clock) */ | |
vcoinput = ((HSE_VALUE / (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM))); | |
} | |
/* PLLI2S_VCO Output = PLLI2S_VCO Input * PLLI2SN */ | |
/* SAI_CLK(first level) = PLLI2S_VCO Output/PLLI2SQ */ | |
tmpreg = (RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SQ) >> 24; | |
frequency = (vcoinput * ((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SN) >> 6))/(tmpreg); | |
/* SAI_CLK_x = SAI_CLK(first level)/PLLI2SDIVQ */ | |
tmpreg = ((RCC->DCKCFGR1 & RCC_DCKCFGR1_PLLI2SDIVQ) + 1); | |
frequency = frequency/(tmpreg); | |
break; | |
} | |
case RCC_DCKCFGR1_SAI1SEL_1: /* External clock is the clock source for SAI1 */ | |
{ | |
frequency = EXTERNAL_CLOCK_VALUE; | |
break; | |
} | |
#if defined (STM32F765xx) || defined (STM32F767xx) || defined (STM32F769xx) || defined (STM32F777xx) || defined (STM32F779xx) | |
case RCC_DCKCFGR1_SAI1SEL: /* HSI or HSE is the clock source for SAI*/ | |
{ | |
if((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSI) | |
{ | |
/* In Case the main PLL Source is HSI */ | |
frequency = HSI_VALUE; | |
} | |
else | |
{ | |
/* In Case the main PLL Source is HSE */ | |
frequency = HSE_VALUE; | |
} | |
break; | |
} | |
#endif /* STM32F767xx || STM32F769xx || STM32F777xx || STM32F779xx */ | |
default : | |
{ | |
break; | |
} | |
} | |
} | |
if (PeriphClk == RCC_PERIPHCLK_SAI2) | |
{ | |
saiclocksource = RCC->DCKCFGR1; | |
saiclocksource &= RCC_DCKCFGR1_SAI2SEL; | |
switch (saiclocksource) | |
{ | |
case 0: /* PLLSAI is the clock source for SAI*/ | |
{ | |
/* Configure the PLLSAI division factor */ | |
/* PLLSAI_VCO Input = PLL_SOURCE/PLLM */ | |
if((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSI) | |
{ | |
/* In Case the PLL Source is HSI (Internal Clock) */ | |
vcoinput = (HSI_VALUE / (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM)); | |
} | |
else | |
{ | |
/* In Case the PLL Source is HSE (External Clock) */ | |
vcoinput = ((HSE_VALUE / (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM))); | |
} | |
/* PLLSAI_VCO Output = PLLSAI_VCO Input * PLLSAIN */ | |
/* SAI_CLK(first level) = PLLSAI_VCO Output/PLLSAIQ */ | |
tmpreg = (RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIQ) >> 24; | |
frequency = (vcoinput * ((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIN) >> 6))/(tmpreg); | |
/* SAI_CLK_x = SAI_CLK(first level)/PLLSAIDIVQ */ | |
tmpreg = (((RCC->DCKCFGR1 & RCC_DCKCFGR1_PLLSAIDIVQ) >> 8) + 1); | |
frequency = frequency/(tmpreg); | |
break; | |
} | |
case RCC_DCKCFGR1_SAI2SEL_0: /* PLLI2S is the clock source for SAI2 */ | |
{ | |
/* Configure the PLLI2S division factor */ | |
/* PLLI2S_VCO Input = PLL_SOURCE/PLLM */ | |
if((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSI) | |
{ | |
/* In Case the PLL Source is HSI (Internal Clock) */ | |
vcoinput = (HSI_VALUE / (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM)); | |
} | |
else | |
{ | |
/* In Case the PLL Source is HSE (External Clock) */ | |
vcoinput = ((HSE_VALUE / (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM))); | |
} | |
/* PLLI2S_VCO Output = PLLI2S_VCO Input * PLLI2SN */ | |
/* SAI_CLK(first level) = PLLI2S_VCO Output/PLLI2SQ */ | |
tmpreg = (RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SQ) >> 24; | |
frequency = (vcoinput * ((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SN) >> 6))/(tmpreg); | |
/* SAI_CLK_x = SAI_CLK(first level)/PLLI2SDIVQ */ | |
tmpreg = ((RCC->DCKCFGR1 & RCC_DCKCFGR1_PLLI2SDIVQ) + 1); | |
frequency = frequency/(tmpreg); | |
break; | |
} | |
case RCC_DCKCFGR1_SAI2SEL_1: /* External clock is the clock source for SAI2 */ | |
{ | |
frequency = EXTERNAL_CLOCK_VALUE; | |
break; | |
} | |
#if defined (STM32F765xx) || defined (STM32F767xx) || defined (STM32F769xx) || defined (STM32F777xx) || defined (STM32F779xx) | |
case RCC_DCKCFGR1_SAI2SEL: /* HSI or HSE is the clock source for SAI2 */ | |
{ | |
if((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSI) | |
{ | |
/* In Case the main PLL Source is HSI */ | |
frequency = HSI_VALUE; | |
} | |
else | |
{ | |
/* In Case the main PLL Source is HSE */ | |
frequency = HSE_VALUE; | |
} | |
break; | |
} | |
#endif /* STM32F767xx || STM32F769xx || STM32F777xx || STM32F779xx */ | |
default : | |
{ | |
break; | |
} | |
} | |
} | |
return frequency; | |
} | |
#if defined (STM32F765xx) || defined(STM32F767xx) || defined(STM32F769xx) || defined(STM32F777xx) || defined(STM32F779xx) | |
/** | |
* @brief Initializes the RCC Oscillators according to the specified parameters in the | |
* RCC_OscInitTypeDef. | |
* @param RCC_OscInitStruct: pointer to an RCC_OscInitTypeDef structure that | |
* contains the configuration information for the RCC Oscillators. | |
* @note The PLL is not disabled when used as system clock. | |
* @note Transitions LSE Bypass to LSE On and LSE On to LSE Bypass are not | |
* supported by this function. User should request a transition to LSE Off | |
* first and then LSE On or LSE Bypass. | |
* @note Transition HSE Bypass to HSE On and HSE On to HSE Bypass are not | |
* supported by this function. User should request a transition to HSE Off | |
* first and then HSE On or HSE Bypass. | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_RCC_OscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct) | |
{ | |
uint32_t tickstart = 0; | |
/* Check the parameters */ | |
assert_param(IS_RCC_OSCILLATORTYPE(RCC_OscInitStruct->OscillatorType)); | |
/*------------------------------- HSE Configuration ------------------------*/ | |
if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_HSE) == RCC_OSCILLATORTYPE_HSE) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_HSE(RCC_OscInitStruct->HSEState)); | |
/* When the HSE is used as system clock or clock source for PLL, It can not be disabled */ | |
if((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_HSE) | |
|| ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_PLLCLK) && ((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLCFGR_PLLSRC_HSE))) | |
{ | |
if((__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != RESET) && (RCC_OscInitStruct->HSEState == RCC_HSE_OFF)) | |
{ | |
return HAL_ERROR; | |
} | |
} | |
else | |
{ | |
/* Set the new HSE configuration ---------------------------------------*/ | |
__HAL_RCC_HSE_CONFIG(RCC_OscInitStruct->HSEState); | |
/* Check the HSE State */ | |
if(RCC_OscInitStruct->HSEState != RCC_HSE_OFF) | |
{ | |
/* Get Start Tick*/ | |
tickstart = HAL_GetTick(); | |
/* Wait till HSE is ready */ | |
while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) == RESET) | |
{ | |
if((HAL_GetTick() - tickstart ) > HSE_TIMEOUT_VALUE) | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
else | |
{ | |
/* Get Start Tick*/ | |
tickstart = HAL_GetTick(); | |
/* Wait till HSE is bypassed or disabled */ | |
while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != RESET) | |
{ | |
if((HAL_GetTick() - tickstart ) > HSE_TIMEOUT_VALUE) | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
} | |
} | |
/*----------------------------- HSI Configuration --------------------------*/ | |
if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_HSI) == RCC_OSCILLATORTYPE_HSI) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_HSI(RCC_OscInitStruct->HSIState)); | |
assert_param(IS_RCC_CALIBRATION_VALUE(RCC_OscInitStruct->HSICalibrationValue)); | |
/* Check if HSI is used as system clock or as PLL source when PLL is selected as system clock */ | |
if((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_HSI) | |
|| ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_PLLCLK) && ((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLCFGR_PLLSRC_HSI))) | |
{ | |
/* When HSI is used as system clock it will not disabled */ | |
if((__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) != RESET) && (RCC_OscInitStruct->HSIState != RCC_HSI_ON)) | |
{ | |
return HAL_ERROR; | |
} | |
/* Otherwise, just the calibration is allowed */ | |
else | |
{ | |
/* Adjusts the Internal High Speed oscillator (HSI) calibration value.*/ | |
__HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->HSICalibrationValue); | |
} | |
} | |
else | |
{ | |
/* Check the HSI State */ | |
if((RCC_OscInitStruct->HSIState)!= RCC_HSI_OFF) | |
{ | |
/* Enable the Internal High Speed oscillator (HSI). */ | |
__HAL_RCC_HSI_ENABLE(); | |
/* Get Start Tick*/ | |
tickstart = HAL_GetTick(); | |
/* Wait till HSI is ready */ | |
while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) == RESET) | |
{ | |
if((HAL_GetTick() - tickstart ) > HSI_TIMEOUT_VALUE) | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
/* Adjusts the Internal High Speed oscillator (HSI) calibration value.*/ | |
__HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->HSICalibrationValue); | |
} | |
else | |
{ | |
/* Disable the Internal High Speed oscillator (HSI). */ | |
__HAL_RCC_HSI_DISABLE(); | |
/* Get Start Tick*/ | |
tickstart = HAL_GetTick(); | |
/* Wait till HSI is ready */ | |
while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) != RESET) | |
{ | |
if((HAL_GetTick() - tickstart ) > HSI_TIMEOUT_VALUE) | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
} | |
} | |
/*------------------------------ LSI Configuration -------------------------*/ | |
if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_LSI) == RCC_OSCILLATORTYPE_LSI) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_LSI(RCC_OscInitStruct->LSIState)); | |
/* Check the LSI State */ | |
if((RCC_OscInitStruct->LSIState)!= RCC_LSI_OFF) | |
{ | |
/* Enable the Internal Low Speed oscillator (LSI). */ | |
__HAL_RCC_LSI_ENABLE(); | |
/* Get Start Tick*/ | |
tickstart = HAL_GetTick(); | |
/* Wait till LSI is ready */ | |
while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSIRDY) == RESET) | |
{ | |
if((HAL_GetTick() - tickstart ) > LSI_TIMEOUT_VALUE) | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
else | |
{ | |
/* Disable the Internal Low Speed oscillator (LSI). */ | |
__HAL_RCC_LSI_DISABLE(); | |
/* Get Start Tick*/ | |
tickstart = HAL_GetTick(); | |
/* Wait till LSI is ready */ | |
while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSIRDY) != RESET) | |
{ | |
if((HAL_GetTick() - tickstart ) > LSI_TIMEOUT_VALUE) | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
} | |
/*------------------------------ LSE Configuration -------------------------*/ | |
if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_LSE) == RCC_OSCILLATORTYPE_LSE) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_LSE(RCC_OscInitStruct->LSEState)); | |
/* Enable Power Clock*/ | |
__HAL_RCC_PWR_CLK_ENABLE(); | |
/* Enable write access to Backup domain */ | |
PWR->CR1 |= PWR_CR1_DBP; | |
/* Wait for Backup domain Write protection disable */ | |
tickstart = HAL_GetTick(); | |
while((PWR->CR1 & PWR_CR1_DBP) == RESET) | |
{ | |
if((HAL_GetTick() - tickstart ) > RCC_DBP_TIMEOUT_VALUE) | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
/* Set the new LSE configuration -----------------------------------------*/ | |
__HAL_RCC_LSE_CONFIG(RCC_OscInitStruct->LSEState); | |
/* Check the LSE State */ | |
if((RCC_OscInitStruct->LSEState) != RCC_LSE_OFF) | |
{ | |
/* Get Start Tick*/ | |
tickstart = HAL_GetTick(); | |
/* Wait till LSE is ready */ | |
while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == RESET) | |
{ | |
if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
else | |
{ | |
/* Get Start Tick*/ | |
tickstart = HAL_GetTick(); | |
/* Wait till LSE is ready */ | |
while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) != RESET) | |
{ | |
if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
} | |
/*-------------------------------- PLL Configuration -----------------------*/ | |
/* Check the parameters */ | |
assert_param(IS_RCC_PLL(RCC_OscInitStruct->PLL.PLLState)); | |
if ((RCC_OscInitStruct->PLL.PLLState) != RCC_PLL_NONE) | |
{ | |
/* Check if the PLL is used as system clock or not */ | |
if(__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_PLLCLK) | |
{ | |
if((RCC_OscInitStruct->PLL.PLLState) == RCC_PLL_ON) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_PLLSOURCE(RCC_OscInitStruct->PLL.PLLSource)); | |
assert_param(IS_RCC_PLLM_VALUE(RCC_OscInitStruct->PLL.PLLM)); | |
assert_param(IS_RCC_PLLN_VALUE(RCC_OscInitStruct->PLL.PLLN)); | |
assert_param(IS_RCC_PLLP_VALUE(RCC_OscInitStruct->PLL.PLLP)); | |
assert_param(IS_RCC_PLLQ_VALUE(RCC_OscInitStruct->PLL.PLLQ)); | |
assert_param(IS_RCC_PLLR_VALUE(RCC_OscInitStruct->PLL.PLLR)); | |
/* Disable the main PLL. */ | |
__HAL_RCC_PLL_DISABLE(); | |
/* Get Start Tick*/ | |
tickstart = HAL_GetTick(); | |
/* Wait till PLL is ready */ | |
while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) != RESET) | |
{ | |
if((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE) | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
/* Configure the main PLL clock source, multiplication and division factors. */ | |
__HAL_RCC_PLL_CONFIG(RCC_OscInitStruct->PLL.PLLSource, | |
RCC_OscInitStruct->PLL.PLLM, | |
RCC_OscInitStruct->PLL.PLLN, | |
RCC_OscInitStruct->PLL.PLLP, | |
RCC_OscInitStruct->PLL.PLLQ, | |
RCC_OscInitStruct->PLL.PLLR); | |
/* Enable the main PLL. */ | |
__HAL_RCC_PLL_ENABLE(); | |
/* Get Start Tick*/ | |
tickstart = HAL_GetTick(); | |
/* Wait till PLL is ready */ | |
while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) == RESET) | |
{ | |
if((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE) | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
else | |
{ | |
/* Disable the main PLL. */ | |
__HAL_RCC_PLL_DISABLE(); | |
/* Get Start Tick*/ | |
tickstart = HAL_GetTick(); | |
/* Wait till PLL is ready */ | |
while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) != RESET) | |
{ | |
if((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE) | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
} | |
else | |
{ | |
return HAL_ERROR; | |
} | |
} | |
return HAL_OK; | |
} | |
#endif /* STM32F767xx || STM32F769xx || STM32F777xx || STM32F779xx */ | |
/** | |
* @} | |
*/ | |
/** | |
* @} | |
*/ | |
#endif /* HAL_RCC_MODULE_ENABLED */ | |
/** | |
* @} | |
*/ | |
/** | |
* @} | |
*/ | |
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |