| # Copyright (c) 2016-2021 Nordic Semiconductor ASA |
| # SPDX-License-Identifier: Apache-2.0 |
| |
| config ZEPHYR_HAL_NORDIC_MODULE |
| bool |
| |
| config HAS_NORDIC_DRIVERS |
| bool |
| |
| menu "Nordic drivers" |
| depends on HAS_NORDIC_DRIVERS |
| |
| choice NRF_802154_SOURCE |
| prompt "Source of the IEEE 802.15.4 radio driver" |
| |
| config NRF_802154_SOURCE_HAL_NORDIC |
| bool "Open source" |
| |
| endchoice |
| |
| menuconfig NRF_802154_RADIO_DRIVER |
| bool "NRF IEEE 802.15.4 radio driver" |
| depends on HAS_HW_NRF_RADIO_IEEE802154 |
| select DYNAMIC_INTERRUPTS |
| select ENTROPY_GENERATOR |
| select CLOCK_CONTROL |
| depends on !$(dt_nodelabel_enabled,timer1) |
| help |
| This option enables nRF IEEE 802.15.4 radio driver in Zephyr. Note, |
| that beside the radio peripheral itself, this drivers occupies several |
| other peripherals. A complete list can be found in the hal_nordic |
| repository, within drivers/nrf_radio_802154/nrf_802154_peripherals.h |
| file. As the nRF IEEE 802.15.4 radio driver defines IRQ configuration |
| abstraction layer API and its Zephyr-specific implementation uses dynamic |
| interrupts, the DYNAMIC_INTERRUPTS switch is selected unconditionally. |
| |
| if NRF_802154_RADIO_DRIVER |
| |
| config NRF_802154_MULTIPROTOCOL_SUPPORT |
| bool |
| help |
| In dynamic multiprotocol applications, access to the radio peripheral |
| must be distributed by an arbiter. To support this arbitration |
| in the driver, this option must be enabled. Otherwise, the driver |
| assumes that access to the radio peripheral is granted indefinitely. |
| |
| choice NRF_802154_SL_TYPE |
| prompt "nRF IEEE 802.15.4 Service Layer Type" |
| |
| config NRF_802154_SL_OPENSOURCE |
| bool "Open source" |
| select SENSOR if NRF_802154_TEMPERATURE_UPDATE |
| select TEMP_NRF5 if NRF_802154_TEMPERATURE_UPDATE |
| |
| endchoice |
| |
| config NRF_802154_TEMPERATURE_UPDATE |
| bool "nRF 802.15.4 temperature update" |
| default y if !SOC_NRF54H20 |
| help |
| Enable temperature update for nRF 802.15.4 driver |
| |
| config NRF_802154_TEMPERATURE_UPDATE_INIT_PRIO |
| int "nRF52 IEEE 802.15.4 temperature update initialization priority" |
| depends on NRF_802154_TEMPERATURE_UPDATE |
| default 91 |
| help |
| Set the initialization priority of a temperature update for nRF 802.15.4 driver. |
| |
| config NRF_802154_TEMPERATURE_UPDATE_PERIOD |
| int "nRF 802.15.4 temperature update period in milliseconds" |
| depends on NRF_802154_TEMPERATURE_UPDATE |
| default 60000 |
| help |
| Period of a temperature update for nRF 802.15.4 driver in milliseconds |
| |
| endif # NRF_802154_RADIO_DRIVER |
| |
| config NRF_802154_SERIALIZATION |
| bool |
| select IPC_SERVICE |
| select MBOX |
| help |
| This helper symbol indicates that the nRF 802.15.4 serialization is available. |
| |
| config NRF_802154_SER_HOST |
| bool "nRF IEEE 802.15.4 Driver serialization host" |
| depends on !NRF_802154_RADIO_DRIVER |
| depends on !HAS_HW_NRF_RADIO_IEEE802154 |
| select IEEE802154_NRF5_EXT_IRQ_MGMT if IEEE802154_NRF5 |
| select NRF_802154_SERIALIZATION |
| help |
| Enable serialization of nRF IEEE 802.15.4 Driver. This option is to be |
| used if radio is not available in the core, but radio services are |
| provided by a serialization backend. |
| |
| menuconfig NRF_802154_SER_RADIO |
| bool "nRF IEEE 802.15.4 Driver serialization radio" |
| depends on HAS_HW_NRF_RADIO_IEEE802154 |
| depends on !IEEE802154_NRF5 |
| select NRF_802154_RADIO_DRIVER |
| select NRF_802154_SERIALIZATION |
| help |
| Enable serialization of nRF IEEE 802.15.4 Driver. This option is to be |
| used if radio is available in the core to provide radio services over |
| a serialization backend. |
| |
| if NRF_802154_SER_RADIO |
| |
| config NRF_802154_SER_RADIO_INIT_PRIO |
| int "nRF52 IEEE 802.15.4 serialization initialization priority" |
| default 51 |
| help |
| Set the initialization priority number. Do not mess with it unless |
| you know what you are doing. |
| |
| endif |
| |
| menu "nRF 802.15.4 serialization" |
| depends on NRF_802154_SER_HOST || NRF_802154_SER_RADIO |
| |
| config NRF_802154_SER_LOG |
| bool "802.15.4 serialization logs" |
| default n |
| help |
| This option enable debug logs of 802.15.4 serialization module. |
| |
| config NRF_802154_SER_DEFAULT_RESPONSE_TIMEOUT |
| int "Default Spinel serialization response timeout in milliseconds" |
| default 500 |
| help |
| This option specifies default timeout of spinel status response |
| in milliseconds. |
| |
| endmenu # NRF_802154_SER_HOST || NRF_802154_SER_RADIO |
| |
| if NRF_802154_RADIO_DRIVER || NRF_802154_SERIALIZATION |
| |
| choice NRF_802154_CCA_MODE |
| prompt "nRF IEEE 802.15.4 CCA mode" |
| default NRF_802154_CCA_MODE_ED |
| help |
| CCA mode |
| |
| config NRF_802154_CCA_MODE_ED |
| bool "Energy Above Threshold" |
| |
| config NRF_802154_CCA_MODE_CARRIER |
| bool "Carrier Seen" |
| |
| config NRF_802154_CCA_MODE_CARRIER_AND_ED |
| bool "Energy Above Threshold AND Carrier Seen" |
| |
| config NRF_802154_CCA_MODE_CARRIER_OR_ED |
| bool "Energy Above Threshold OR Carrier Seen" |
| |
| endchoice |
| |
| config NRF_802154_CCA_ED_THRESHOLD |
| int "nRF IEEE 802.15.4 CCA Energy Detection threshold" |
| default 45 |
| help |
| If energy detected in a given channel is above the value then the |
| channel is deemed busy. The unit is defined as per 802.15.4-2006 spec. |
| |
| config NRF_802154_CCA_CORR_THRESHOLD |
| int "nRF IEEE 802.15.4 CCA Correlator threshold" |
| default 45 |
| |
| config NRF_802154_CCA_CORR_LIMIT |
| int "nRF IEEE 802.15.4 CCA Correlator limit" |
| default 2 |
| help |
| Limit for occurrences above correlator threshold. When not equal to |
| zero the correlator based signal detect is enabled. |
| |
| config NRF_802154_RX_BUFFERS |
| int "nRF 802.15.4 receive buffers" |
| default 16 |
| help |
| Number of buffers in nRF 802.15.4 driver serialization host's receive queue. |
| If this value is modified, its remote counterpart must be set to the exact same value. |
| |
| config NRF_802154_PENDING_SHORT_ADDRESSES |
| int "nRF 802.15.4 pending short addresses" |
| default 16 |
| help |
| Number of slots containing short addresses of nodes for which pending data is stored |
| |
| config NRF_802154_PENDING_EXTENDED_ADDRESSES |
| int "nRF 802.15.4 pending extended addresses" |
| default 16 |
| help |
| Number of slots containing extended addresses of nodes for which pending data is stored |
| |
| config NRF_802154_ENCRYPTION |
| bool "nRF 802.15.4 AES-CCM* authentication & encryption" |
| depends on !CRYPTO_NRF_ECB |
| |
| config NRF_802154_SECURITY_KEY_STORAGE_SIZE |
| int "nRF 802.15.4 security key storage size" |
| default 3 |
| help |
| Number of encryption keys that the nRF 802.15.4 Radio Driver can store simultaneously. |
| |
| config NRF_802154_CARRIER_FUNCTIONS |
| bool "nRF 802.15.4 carrier functions" |
| default y if (OPENTHREAD_DIAG || IEEE802154_CARRIER_FUNCTIONS) |
| help |
| This option enables functions such as modulated carrier and continuous carrier. |
| If this option is modified on a multicore SoC, its remote counterpart must be set to the exact same value. |
| |
| choice NRF_802154_ASSERT_CHOICE |
| prompt "nRF 802.15.4 assert implementation" |
| default NRF_802154_ASSERT_ZEPHYR_MINIMAL |
| |
| config NRF_802154_ASSERT_ZEPHYR_MINIMAL |
| bool "nRF 802.15.4 minimal assertions" |
| help |
| This option provides minimal run-time checking of the nRF 802.15.4 Radio Driver's operation, |
| even if kernel-wide CONFIG_ASSERT is disabled. In case of an abnormal condition the function |
| `nrf_802154_assert_handler()` is called. File and line debug information are not provided |
| to save memory of the image file. Default implementation of the `nrf_802154_assert_handler` |
| involves a call to `k_panic`/`k_oops` and allows further tweaking of the behavior. |
| You can also provide your own implementation of `nrf_802154_assert_handler`. |
| |
| config NRF_802154_ASSERT_ZEPHYR |
| bool "nRF 802.15.4 Radio Driver assertions as Zephyr's standard __ASERT_NO_MSG" |
| help |
| The run-time checking of the nRF 802.15.4 Radio Driver depends fully on the configuration |
| of the `__ASSERT_NO_MSG` macro, including the ability to completely turn off the run-time |
| checking. |
| |
| endchoice # NRF_802154_ASSERT_CHOICE |
| |
| endif # NRF_802154_RADIO_DRIVER || NRF_802154_SERIALIZATION |
| |
| endmenu # HAS_NORDIC_DRIVERS |
| |
| rsource "nrfs/Kconfig" |
| rsource "nrfx/Kconfig" |
| rsource "Kconfig.nrf_regtool" |
