| # Kconfig - BMC150 magnetometer sensor configuration options |
| |
| # |
| # Copyright (c) 2016 Intel Corporation |
| # |
| # SPDX-License-Identifier: Apache-2.0 |
| # |
| |
| menuconfig BMC150_MAGN |
| bool "BMC150_MAGN I2C Magnetometer Chip" |
| depends on I2C |
| default n |
| help |
| Enable driver for BMC150 I2C-based magnetometer sensor. |
| |
| config BMC150_MAGN_DEV_NAME |
| string "BMC150_MAGN device name" |
| depends on BMC150_MAGN |
| default "bmc150_magn" |
| |
| config BMC150_MAGN_I2C_ADDR |
| hex "BMC150_MAGN I2C slave address" |
| default 0x12 |
| depends on BMC150_MAGN |
| help |
| Specify the I2C slave address for the BMC150_MAGN. |
| |
| 0x12: GND |
| 0x13: VCC |
| |
| config BMC150_MAGN_I2C_MASTER_DEV_NAME |
| string "I2C master where BMC150_MAGN is connected" |
| depends on BMC150_MAGN |
| default "I2C_0" |
| help |
| Specify the device name of the I2C master device to which BMC150_MAGN |
| is connected. |
| |
| menu "Attributes" |
| depends on BMC150_MAGN |
| |
| choice |
| prompt "Default preset" |
| default BMC150_MAGN_PRESET_REGULAR |
| depends on BMC150_MAGN |
| help |
| Specify the default preset (x/y oversampling, z oversampling, sampling |
| frequency). |
| |
| config BMC150_MAGN_PRESET_LOW_POWER |
| bool |
| prompt "Low power (3, 3, 10)" |
| |
| config BMC150_MAGN_PRESET_REGULAR |
| bool |
| prompt "Regular (9, 15, 10)" |
| |
| config BMC150_MAGN_PRESET_ENHANCED_REGULAR |
| bool |
| prompt "Enhanced regular (15, 27, 10)" |
| |
| config BMC150_MAGN_PRESET_HIGH_ACCURACY |
| bool |
| prompt "High accuracy (47, 83, 20)" |
| |
| endchoice |
| |
| config BMC150_MAGN_SAMPLING_RATE_RUNTIME |
| bool "Enable dynamic sampling rate" |
| depends on BMC150_MAGN |
| default n |
| help |
| Enable alteration of sampling rate attribute at runtime. |
| |
| config BMC150_MAGN_SAMPLING_REP_XY |
| bool "Enable dynamic XY oversampling" |
| depends on BMC150_MAGN |
| default n |
| help |
| Enable alteration of XY oversampling at runtime. |
| |
| config BMC150_MAGN_SAMPLING_REP_Z |
| bool "Enable dynamic Z oversampling" |
| depends on BMC150_MAGN |
| default n |
| help |
| Enable alteration of Z oversampling at runtime. |
| |
| endmenu |
| |
| config BMC150_MAGN_TRIGGER |
| bool "Enable triggers" |
| depends on BMC150_MAGN && GPIO |
| default n |
| help |
| Enable triggers for BMC150 magnetometer |
| |
| config BMC150_MAGN_TRIGGER_THREAD_STACK |
| int "Thread stack size" |
| depends on BMC150_MAGN_TRIGGER |
| default 1024 |
| help |
| Specify the internal thread stack size. |
| |
| config BMC150_MAGN_TRIGGER_DRDY |
| bool "Enable data ready trigger" |
| depends on BMC150_MAGN_TRIGGER |
| default n |
| help |
| Enable data ready interrupt for BMC150 magnetometer |
| |
| config BMC150_MAGN_GPIO_DRDY_DEV_NAME |
| string "GPIO device where BMC150_MAGN data ready interrupt is connected" |
| depends on BMC150_MAGN_TRIGGER_DRDY |
| default GPIO_0 |
| help |
| Specify the device name of the GPIO controller the BMC150_MAGN interrupt |
| is connected to. |
| |
| config BMC150_MAGN_GPIO_DRDY_INT_PIN |
| int |
| default 3 |
| depends on BMC150_MAGN_TRIGGER_DRDY |
| prompt "GPIO pin number for the data ready interrupt pin" |
| help |
| GPIO pin number for the data ready interrupt pin. |
