| # BL5340-DVK board configuration |
| |
| # Copyright (c) 2019-2020 Nordic Semiconductor ASA |
| # Copyright (c) 2021 Laird Connectivity |
| # SPDX-License-Identifier: Apache-2.0 |
| |
| if BOARD_BL5340_DVK_CPUAPP || BOARD_BL5340_DVK_CPUAPP_NS |
| |
| config BOARD |
| default "bl5340_dvk_cpuapp" if BOARD_BL5340_DVK_CPUAPP || BOARD_BL5340_DVK_CPUAPP_NS |
| |
| |
| config FLASH |
| default y |
| |
| if BOARD_BL5340_DVK_CPUAPP |
| |
| # Enable QSPI for secondary partition maps |
| |
| config NORDIC_QSPI_NOR |
| default y |
| |
| if DAC |
| |
| config DAC_MCP4725 |
| default y |
| |
| config DAC_INIT_PRIORITY |
| default 80 |
| |
| config I2C |
| default y |
| |
| endif # DAC |
| |
| endif # BOARD_BL5340_DVK_CPUAPP |
| |
| # By default, if we build for a Non-Secure version of the board, |
| # force building with TF-M as the Secure Execution Environment. |
| |
| config BUILD_WITH_TFM |
| default y if BOARD_BL5340_DVK_CPUAPP_NS |
| |
| if BUILD_WITH_TFM |
| |
| # By default, if we build with TF-M, instruct build system to |
| # flash the combined TF-M (Secure) & Zephyr (Non Secure) image |
| config TFM_FLASH_MERGED_BINARY |
| bool |
| default y |
| |
| endif # BUILD_WITH_TFM |
| |
| # Code Partition: |
| # |
| # For the secure version of the board the firmware is linked at the beginning |
| # of the flash, or into the code-partition defined in DT if it is intended to |
| # be loaded by MCUboot. If the secure firmware is to be combined with a non- |
| # secure image (TRUSTED_EXECUTION_SECURE=y), the secure FW image shall always |
| # be restricted to the size of its code partition. |
| # |
| # For the non-secure version of the board, the firmware |
| # must be linked into the code-partition (non-secure) defined in DT, regardless. |
| # Apply this configuration below by setting the Kconfig symbols used by |
| # the linker according to the information extracted from DT partitions. |
| |
| # SRAM Partition: |
| # |
| # If the secure firmware is to be combined with a non-secure image |
| # (TRUSTED_EXECUTION_SECURE=y), the secure FW image SRAM shall always |
| # be restricted to the secure image SRAM partition (sram-secure-partition). |
| # Otherwise (if TRUSTED_EXECUTION_SECURE is not set) the whole zephyr,sram |
| # may be used by the image. |
| # |
| # For the non-secure version of the board, the firmware image SRAM is |
| # always restricted to the allocated non-secure SRAM partition. |
| # |
| # Workaround for not being able to have commas in macro arguments |
| DT_CHOSEN_Z_CODE_PARTITION := zephyr,code-partition |
| DT_CHOSEN_Z_SRAM_PARTITION := zephyr,sram-secure-partition |
| |
| if BOARD_BL5340_DVK_CPUAPP && TRUSTED_EXECUTION_SECURE |
| |
| config FLASH_LOAD_SIZE |
| default $(dt_chosen_reg_size_hex,$(DT_CHOSEN_Z_CODE_PARTITION)) |
| |
| config SRAM_SIZE |
| default $(dt_chosen_reg_size_int,$(DT_CHOSEN_Z_SRAM_PARTITION),0,K) |
| |
| endif # BOARD_BL5340_DVK_CPUAPP && TRUSTED_EXECUTION_SECURE |
| |
| if BOARD_BL5340_DVK_CPUAPP_NS |
| |
| config FLASH_LOAD_OFFSET |
| default $(dt_chosen_reg_addr_hex,$(DT_CHOSEN_Z_CODE_PARTITION)) |
| |
| config FLASH_LOAD_SIZE |
| default $(dt_chosen_reg_size_hex,$(DT_CHOSEN_Z_CODE_PARTITION)) |
| |
| endif # BOARD_BL5340_DVK_CPUAPP_NS |
| |
| # Workaround for not being able to have commas in macro arguments |
| DT_COMPAT_TI_TCA9538 := ti,tca9538 |
| |
| config I2C |
| default $(dt_compat_on_bus,$(DT_COMPAT_TI_TCA9538),i2c) |
| |
| endif # BOARD_BL5340_DVK_CPUAPP || BOARD_BL5340_DVK_CPUAPP_NS |
| |
| config BOARD |
| default "bl5340_dvk_cpunet" if BOARD_BL5340_DVK_CPUNET |