blob: 38acc3dc1dcc37f1649bbe6901f2f5ddd35497c1 [file] [log] [blame]
.. _ip_k66f:
SEGGER IP Switch Board
######################
Overview
********
The Segger IP Switch Board is a Evaluation board based on NXP Kinetis K66 MCU.
It comes with Micrel/Microchip KSZ8794CNX integrated 4-port 10/100 managed
Ethernet switch with Gigabit RGMII/MII/RMII interface.
- KSZ8794CNX enables evaluation for switch functions
- On-board debug probe J-Link-OB for programming
.. image:: ./ip_k66f.png
:width: 720px
:align: center
:alt: IP-K66F
Hardware
********
- MK66FN2M0VMD18 MCU (180 MHz, 2 MB flash memory, 256 KB RAM, low-power,
crystal-less USB
- Dual role USB interface with micro-B USB connector
- 2 User LED
- On-board debug probe J-Link-OB for programming
- Micrel/Microchip Ethernet Switch KSZ8794CNX with 3 RJ45 connectors
For more information about the K66F SoC and IP-K66F board:
- `K66F Website`_
- `K66F Datasheet`_
- `K66F Reference Manual`_
- `IP-K66F Website`_
- `IP-K66F User Guide`_
- `IP-K66F Schematics`_
Supported Features
==================
The ip_k66f board configuration supports the following hardware features:
+-----------+------------+-------------------------------------+
| Interface | Controller | Driver/Component |
+===========+============+=====================================+
| NVIC | on-chip | nested vector interrupt controller |
+-----------+------------+-------------------------------------+
| SYSTICK | on-chip | systick |
+-----------+------------+-------------------------------------+
| PINMUX | on-chip | pinmux |
+-----------+------------+-------------------------------------+
| GPIO | on-chip | gpio |
+-----------+------------+-------------------------------------+
| WATCHDOG | on-chip | watchdog |
+-----------+------------+-------------------------------------+
| FLASH | on-chip | soc flash |
+-----------+------------+-------------------------------------+
| RTC | on-chip | rtc |
+-----------+------------+-------------------------------------+
The default configuration can be found in the defconfig file:
``boards/arm/ip_k66f/ip_k66f_defconfig``
Micrel/Microchip KSZ8794CNX Ethernet Switch is not currently
supported.
Connections and IOs
===================
The K66F SoC has five pairs of pinmux/gpio controllers.
+-------+-----------------+---------------------------+
| Name | Function | Usage |
+=======+=================+===========================+
| PTA8 | GPIO | Red LED |
+-------+-----------------+---------------------------+
| PTA10 | GPIO | RED LED |
+-------+-----------------+---------------------------+
System Clock
============
The K66F SoC is configured to use the 12 MHz low gain crystal oscillator on the
board with the on-chip PLL to generate a 180 MHz system clock.
Serial Port
===========
The K66F SoC has six UARTs. None of them are used.
Programming and Debugging
*************************
Build and flash applications as usual (see :ref:`build_an_application` and
:ref:`application_run` for more details).
Configuring a Debug Probe
=========================
A debug probe is used for both flashing and debugging the board. This board is
configured by default to use the :ref:`opensda-jlink-onboard-debug-probe`.
:ref:`opensda-jlink-onboard-debug-probe`
--------------------------------------------------
Install the :ref:`jlink-debug-host-tools` and make sure they are in your search
path.
Follow the instructions in :ref:`opensda-jlink-onboard-debug-probe` to program
the `OpenSDA J-Link Generic Firmware for V3.2 Bootloader`_. Note that Segger
does provide an OpenSDA J-Link Board-Specific Firmware for this board, however
it is not compatible with the DAPLink bootloader.
The default flasher is ``jlink`` using the built-in SEGGER Jlink interface.
Flashing
========
Here is an example for the :ref:`blinky-sample` application.
.. zephyr-app-commands::
:zephyr-app: samples/basic/blinky
:board: ip_k66f
:goals: flash
Red LED0 should blink at 1 second delay.
Debugging
=========
Here is an example for the :ref:`blinky-sample` application.
.. zephyr-app-commands::
:zephyr-app: samples/basic/blinky
:board: ip_k66f
:goals: debug
Step through the application in your debugger.
.. _IP-K66F Website:
https://www.segger.com/evaluate-our-software/segger/embosip-switch-board/
.. _IP-K66F User Guide:
https://www.segger.com/downloads/emnet/UM06002
.. _IP-K66F Schematics:
https://www.segger.com/downloads/emnet/embOSIP_SwitchBoard_V2.0_WEB_Schematic.pdf
.. _K66F Website:
https://www.nxp.com/products/processors-and-microcontrollers/arm-microcontrollers/general-purpose-mcus/k-series-cortex-m4/k6x-ethernet/kinetis-k66-180-mhz-dual-high-speed-full-speed-usbs-2mb-flash-microcontrollers-mcus-based-on-arm-cortex-m4-core:K66_180
.. _K66F Datasheet:
https://www.nxp.com/docs/en/data-sheet/K66P144M180SF5V2.pdf
.. _K66F Reference Manual:
https://www.nxp.com/docs/en/reference-manual/K66P144M180SF5RMV2.pdf
.. _OpenSDA J-Link Generic Firmware for V3.2 Bootloader:
https://www.segger.com/downloads/jlink/OpenSDA_V3_2
Serial console
==============
The ``ip_k66f`` board only uses Segger's RTT console for providing serial
console. There is no physical serial port available.
- To communicate with this board one needs in one console:
``/opt/SEGGER/JLink_V664/JLinkRTTLogger -Device MK66FN2M0XXX18 -RTTChannel 1 -if SWD -Speed 4000 ~/rtt.log``
- In another one:
``nc localhost 19021``