blob: 9ca37a1d93cffc97f1c245877d2bb1bddbd263f5 [file] [log] [blame]
.. _esp32c3_devkitm:
ESP32-C3
########
Overview
********
ESP32-C3 is a single-core Wi-Fi and Bluetooth 5 (LE) microcontroller SoC,
based on the open-source RISC-V architecture. It strikes the right balance of power,
I/O capabilities and security, thus offering the optimal cost-effective
solution for connected devices.
The availability of Wi-Fi and Bluetooth 5 (LE) connectivity not only makes the device configuration easy,
but it also facilitates a variety of use-cases based on dual connectivity. [1]_
The features include the following:
- 32-bit core RISC-V microcontroller with a maximum clock speed of 160 MHz
- 400 KB of internal RAM
- 802.11b/g/n/e/i
- A Bluetooth LE subsystem that supports features of Bluetooth 5 and Bluetooth mesh
- Various peripherals:
- 12-bit ADC with up to 18 channels
- TWAI compatible with CAN bus 2.0
- Temperature sensor
- 4x SPI
- 2x I2S
- 2x I2C
- 3x UART
- LED PWM with up to 16 channels
- Cryptographic hardware acceleration (RNG, ECC, RSA, SHA-2, AES)
System requirements
*******************
Prerequisites
-------------
Espressif HAL requires binary blobs in order work. The west extension below performs the required
syncronization to clone, checkout and pull the submodules:
.. code-block:: console
west espressif update
.. note::
It is recommended running the command above after :file:`west update`.
Building & Flashing
-------------------
Build and flash applications as usual (see :ref:`build_an_application` and
:ref:`application_run` for more details).
.. zephyr-app-commands::
:zephyr-app: samples/hello_world
:board: esp32c3_devkitm
:goals: build
The usual ``flash`` target will work with the ``esp32c3_devkitm`` board
configuration. Here is an example for the :ref:`hello_world`
application.
.. zephyr-app-commands::
:zephyr-app: samples/hello_world
:board: esp32c3_devkitm
:goals: flash
Open the serial monitor using the following command:
.. code-block:: shell
west espressif monitor
After the board has automatically reset and booted, you should see the following
message in the monitor:
.. code-block:: console
***** Booting Zephyr OS vx.x.x-xxx-gxxxxxxxxxxxx *****
Hello World! esp32c3_devkitm
Debugging
---------
As with much custom hardware, the ESP32C3 modules require patches to
OpenOCD that are not upstreamed. Espressif maintains their own fork of
the project. The custom OpenOCD can be obtained by running the following extension:
.. code-block:: console
west espressif install
.. note::
By default, the OpenOCD will be downloaded and installed under $HOME/.espressif/tools/zephyr directory
(%USERPROFILE%/.espressif/tools/zephyr on Windows).
The Zephyr SDK uses a bundled version of OpenOCD by default. You can overwrite that behavior by adding the
``-DOPENOCD=<path/to/bin/openocd> -DOPENOCD_DEFAULT_PATH=<path/to/openocd/share/openocd/scripts>``
parameter when building.
Here is an example for building the :ref:`hello_world` application.
.. zephyr-app-commands::
:zephyr-app: samples/hello_world
:board: esp32c3_devkitm
:goals: build flash
:gen-args: -DOPENOCD=<path/to/bin/openocd> -DOPENOCD_DEFAULT_PATH=<path/to/openocd/share/openocd/scripts>
You can debug an application in the usual way. Here is an example for the :ref:`hello_world` application.
.. zephyr-app-commands::
:zephyr-app: samples/hello_world
:board: esp32c3_devkitm
:goals: debug
References
**********
.. [1] https://www.espressif.com/en/products/socs/esp32-c3
.. _`ESP32C3 Technical Reference Manual`: https://espressif.com/sites/default/files/documentation/esp32-c3_technical_reference_manual_en.pdf
.. _`ESP32C3 Datasheet`: https://www.espressif.com/sites/default/files/documentation/esp32-c3_datasheet_en.pdf