drivers/serial/uart_gecko.c - third_party/github/zephyrproject-rtos/zephyr - Git at Google

 /*
  * Copyright (c) 2017, Christian Taedcke
  *
  * SPDX-License-Identifier: Apache-2.0
  */

 #include <errno.h>
 #include <drivers/uart.h>
 #include <em_usart.h>
 #include <em_gpio.h>
 #include <em_cmu.h>
 #include <soc.h>

 struct uart_gecko_config {
 	USART_TypeDef *base;
 	CMU_Clock_TypeDef clock;
 	u32_t baud_rate;
 #ifdef CONFIG_UART_INTERRUPT_DRIVEN
 	void (*irq_config_func)(struct device *dev);
 #endif
 	struct soc_gpio_pin pin_rx;
 	struct soc_gpio_pin pin_tx;
 #ifdef CONFIG_SOC_GECKO_HAS_INDIVIDUAL_PIN_LOCATION
 	u8_t loc_rx;
 	u8_t loc_tx;
 #else
 	u8_t loc;
 #endif
 };

 struct uart_gecko_data {
 #ifdef CONFIG_UART_INTERRUPT_DRIVEN
 	uart_irq_callback_user_data_t callback;
 	void *cb_data;
 #endif
 };

 static int uart_gecko_poll_in(struct device *dev, unsigned char *c)
 {
 	const struct uart_gecko_config *config = dev->config->config_info;
 	u32_t flags = USART_StatusGet(config->base);

 	if (flags & USART_STATUS_RXDATAV) {
 		*c = USART_Rx(config->base);
 		return 0;
 	}

 	return -1;
 }

 static void uart_gecko_poll_out(struct device *dev, unsigned char c)
 {
 	const struct uart_gecko_config *config = dev->config->config_info;

 	USART_Tx(config->base, c);
 }

 static int uart_gecko_err_check(struct device *dev)
 {
 	const struct uart_gecko_config *config = dev->config->config_info;
 	u32_t flags = USART_IntGet(config->base);
 	int err = 0;

 	if (flags & USART_IF_RXOF) {
 		err |= UART_ERROR_OVERRUN;
 	}

 	if (flags & USART_IF_PERR) {
 		err |= UART_ERROR_PARITY;
 	}

 	if (flags & USART_IF_FERR) {
 		err |= UART_ERROR_FRAMING;
 	}

 	USART_IntClear(config->base, USART_IF_RXOF |
 		       USART_IF_PERR |
 		       USART_IF_FERR);

 	return err;
 }

 #ifdef CONFIG_UART_INTERRUPT_DRIVEN
 static int uart_gecko_fifo_fill(struct device *dev, const u8_t *tx_data,
 			       int len)
 {
 	const struct uart_gecko_config *config = dev->config->config_info;
 	u8_t num_tx = 0U;

 	while ((len - num_tx > 0) &&
 	       (config->base->STATUS & USART_STATUS_TXBL)) {

 		config->base->TXDATA = (u32_t)tx_data[num_tx++];
 	}

 	return num_tx;
 }

 static int uart_gecko_fifo_read(struct device *dev, u8_t *rx_data,
 			       const int len)
 {
 	const struct uart_gecko_config *config = dev->config->config_info;
 	u8_t num_rx = 0U;

 	while ((len - num_rx > 0) &&
 	       (config->base->STATUS & USART_STATUS_RXDATAV)) {

 		rx_data[num_rx++] = (u8_t)config->base->RXDATA;
 	}

 	return num_rx;
 }

 static void uart_gecko_irq_tx_enable(struct device *dev)
 {
 	const struct uart_gecko_config *config = dev->config->config_info;
 	u32_t mask = USART_IEN_TXBL | USART_IEN_TXC;

 	USART_IntEnable(config->base, mask);
 }

 static void uart_gecko_irq_tx_disable(struct device *dev)
 {
 	const struct uart_gecko_config *config = dev->config->config_info;
 	u32_t mask = USART_IEN_TXBL | USART_IEN_TXC;

 	USART_IntDisable(config->base, mask);
 }

 static int uart_gecko_irq_tx_complete(struct device *dev)
 {
 	const struct uart_gecko_config *config = dev->config->config_info;
 	u32_t flags = USART_IntGet(config->base);

 	USART_IntClear(config->base, USART_IF_TXC);

 	return (flags & USART_IF_TXC) != 0U;
 }

 static int uart_gecko_irq_tx_ready(struct device *dev)
 {
 	const struct uart_gecko_config *config = dev->config->config_info;
 	u32_t flags = USART_IntGet(config->base);

 	return (flags & USART_IF_TXBL) != 0U;
 }

 static void uart_gecko_irq_rx_enable(struct device *dev)
 {
 	const struct uart_gecko_config *config = dev->config->config_info;
 	u32_t mask = USART_IEN_RXDATAV;

 	USART_IntEnable(config->base, mask);
 }

 static void uart_gecko_irq_rx_disable(struct device *dev)
 {
 	const struct uart_gecko_config *config = dev->config->config_info;
 	u32_t mask = USART_IEN_RXDATAV;

 	USART_IntDisable(config->base, mask);
 }

 static int uart_gecko_irq_rx_full(struct device *dev)
 {
 	const struct uart_gecko_config *config = dev->config->config_info;
 	u32_t flags = USART_IntGet(config->base);

 	return (flags & USART_IF_RXDATAV) != 0U;
 }

 static int uart_gecko_irq_rx_ready(struct device *dev)
 {
 	const struct uart_gecko_config *config = dev->config->config_info;
 	u32_t mask = USART_IEN_RXDATAV;

 	return (config->base->IEN & mask)
 		&& uart_gecko_irq_rx_full(dev);
 }

 static void uart_gecko_irq_err_enable(struct device *dev)
 {
 	const struct uart_gecko_config *config = dev->config->config_info;

 	USART_IntEnable(config->base, USART_IF_RXOF |
 			 USART_IF_PERR |
 			 USART_IF_FERR);
 }

 static void uart_gecko_irq_err_disable(struct device *dev)
 {
 	const struct uart_gecko_config *config = dev->config->config_info;

 	USART_IntDisable(config->base, USART_IF_RXOF |
 			 USART_IF_PERR |
 			 USART_IF_FERR);
 }

 static int uart_gecko_irq_is_pending(struct device *dev)
 {
 	return uart_gecko_irq_tx_ready(dev) || uart_gecko_irq_rx_ready(dev);
 }

 static int uart_gecko_irq_update(struct device *dev)
 {
 	return 1;
 }

 static void uart_gecko_irq_callback_set(struct device *dev,
 				       uart_irq_callback_user_data_t cb,
 				       void *cb_data)
 {
 	struct uart_gecko_data *data = dev->driver_data;

 	data->callback = cb;
 	data->cb_data = cb_data;
 }

 static void uart_gecko_isr(void *arg)
 {
 	struct device *dev = arg;
 	struct uart_gecko_data *data = dev->driver_data;

 	if (data->callback) {
 		data->callback(data->cb_data);
 	}
 }
 #endif /* CONFIG_UART_INTERRUPT_DRIVEN */

 static void uart_gecko_init_pins(struct device *dev)
 {
 	const struct uart_gecko_config *config = dev->config->config_info;

 	soc_gpio_configure(&config->pin_rx);
 	soc_gpio_configure(&config->pin_tx);
 #ifdef CONFIG_SOC_GECKO_HAS_INDIVIDUAL_PIN_LOCATION
 	config->base->ROUTEPEN = USART_ROUTEPEN_RXPEN | USART_ROUTEPEN_TXPEN;
 	config->base->ROUTELOC0 =
 		(config->loc_tx << _USART_ROUTELOC0_TXLOC_SHIFT) |
 		(config->loc_rx << _USART_ROUTELOC0_RXLOC_SHIFT);
 	config->base->ROUTELOC1 = _USART_ROUTELOC1_RESETVALUE;
 #else
 	config->base->ROUTE = USART_ROUTE_RXPEN | USART_ROUTE_TXPEN
 		| (config->loc << 8);
 #endif
 }

 static int uart_gecko_init(struct device *dev)
 {
 	const struct uart_gecko_config *config = dev->config->config_info;
 	USART_InitAsync_TypeDef usartInit = USART_INITASYNC_DEFAULT;

 	/* The peripheral and gpio clock are already enabled from soc and gpio
 	 * driver
 	 */

 	usartInit.baudrate = config->baud_rate;

 	/* Enable USART clock */
 	CMU_ClockEnable(config->clock, true);

 	/* Init USART */
 	USART_InitAsync(config->base, &usartInit);

 	/* Initialize USART pins */
 	uart_gecko_init_pins(dev);

 #ifdef CONFIG_UART_INTERRUPT_DRIVEN
 	config->irq_config_func(dev);
 #endif

 	return 0;
 }

 static const struct uart_driver_api uart_gecko_driver_api = {
 	.poll_in = uart_gecko_poll_in,
 	.poll_out = uart_gecko_poll_out,
 	.err_check = uart_gecko_err_check,
 #ifdef CONFIG_UART_INTERRUPT_DRIVEN
 	.fifo_fill = uart_gecko_fifo_fill,
 	.fifo_read = uart_gecko_fifo_read,
 	.irq_tx_enable = uart_gecko_irq_tx_enable,
 	.irq_tx_disable = uart_gecko_irq_tx_disable,
 	.irq_tx_complete = uart_gecko_irq_tx_complete,
 	.irq_tx_ready = uart_gecko_irq_tx_ready,
 	.irq_rx_enable = uart_gecko_irq_rx_enable,
 	.irq_rx_disable = uart_gecko_irq_rx_disable,
 	.irq_rx_ready = uart_gecko_irq_rx_ready,
 	.irq_err_enable = uart_gecko_irq_err_enable,
 	.irq_err_disable = uart_gecko_irq_err_disable,
 	.irq_is_pending = uart_gecko_irq_is_pending,
 	.irq_update = uart_gecko_irq_update,
 	.irq_callback_set = uart_gecko_irq_callback_set,
 #endif
 };

 #ifdef DT_INST_0_SILABS_GECKO_UART

 #define PIN_UART0_RXD {DT_INST_0_SILABS_GECKO_UART_LOCATION_RX_1, \
 		DT_INST_0_SILABS_GECKO_UART_LOCATION_RX_2, gpioModeInput, 1}
 #define PIN_UART0_TXD {DT_INST_0_SILABS_GECKO_UART_LOCATION_TX_1, \
 		DT_INST_0_SILABS_GECKO_UART_LOCATION_TX_2, gpioModePushPull, 1}

 #ifdef CONFIG_UART_INTERRUPT_DRIVEN
 static void uart_gecko_config_func_0(struct device *dev);
 #endif

 static const struct uart_gecko_config uart_gecko_0_config = {
 	.base = (USART_TypeDef *)DT_INST_0_SILABS_GECKO_UART_BASE_ADDRESS,
 	.clock = cmuClock_UART0,
 	.baud_rate = DT_INST_0_SILABS_GECKO_UART_CURRENT_SPEED,
 	.pin_rx = PIN_UART0_RXD,
 	.pin_tx = PIN_UART0_TXD,
 #ifdef CONFIG_SOC_GECKO_HAS_INDIVIDUAL_PIN_LOCATION
 	.loc_rx = DT_INST_0_SILABS_GECKO_UART_LOCATION_RX_0,
 	.loc_tx = DT_INST_0_SILABS_GECKO_UART_LOCATION_TX_0,
 #else
 #if DT_INST_0_SILABS_GECKO_UART_LOCATION_RX_0 \
 	!= DT_INST_0_SILABS_GECKO_UART_LOCATION_TX_0
 #error UART_0 DTS location-* properties must have identical value
 #endif
 	.loc = DT_INST_0_SILABS_GECKO_UART_LOCATION_RX_0,
 #endif
 #ifdef CONFIG_UART_INTERRUPT_DRIVEN
 	.irq_config_func = uart_gecko_config_func_0,
 #endif
 };

 static struct uart_gecko_data uart_gecko_0_data;

 DEVICE_AND_API_INIT(uart_0, DT_INST_0_SILABS_GECKO_UART_LABEL, &uart_gecko_init,
 		    &uart_gecko_0_data, &uart_gecko_0_config, PRE_KERNEL_1,
 		    CONFIG_KERNEL_INIT_PRIORITY_DEVICE, &uart_gecko_driver_api);

 #ifdef CONFIG_UART_INTERRUPT_DRIVEN
 static void uart_gecko_config_func_0(struct device *dev)
 {
 	IRQ_CONNECT(DT_INST_0_SILABS_GECKO_UART_IRQ_RX,
 		    DT_INST_0_SILABS_GECKO_UART_IRQ_RX_PRIORITY, uart_gecko_isr,
 		    DEVICE_GET(uart_0), 0);
 	IRQ_CONNECT(DT_INST_0_SILABS_GECKO_UART_IRQ_TX,
 		    DT_INST_0_SILABS_GECKO_UART_IRQ_TX_PRIORITY, uart_gecko_isr,
 		    DEVICE_GET(uart_0), 0);

 	irq_enable(DT_INST_0_SILABS_GECKO_UART_IRQ_RX);
 	irq_enable(DT_INST_0_SILABS_GECKO_UART_IRQ_TX);
 }
 #endif

 #endif /* DT_INST_0_SILABS_GECKO_UART */

 #ifdef DT_INST_1_SILABS_GECKO_UART

 #define PIN_UART1_RXD {DT_INST_1_SILABS_GECKO_UART_LOCATION_RX_1, \
 		DT_INST_1_SILABS_GECKO_UART_LOCATION_RX_2, gpioModeInput, 1}
 #define PIN_UART1_TXD {DT_INST_1_SILABS_GECKO_UART_LOCATION_TX_1, \
 		DT_INST_1_SILABS_GECKO_UART_LOCATION_TX_2, gpioModePushPull, 1}

 #ifdef CONFIG_UART_INTERRUPT_DRIVEN
 static void uart_gecko_config_func_1(struct device *dev);
 #endif

 static const struct uart_gecko_config uart_gecko_1_config = {
 	.base = (USART_TypeDef *)DT_INST_1_SILABS_GECKO_UART_BASE_ADDRESS,
 	.clock = cmuClock_UART1,
 	.baud_rate = DT_INST_1_SILABS_GECKO_UART_CURRENT_SPEED,
 	.pin_rx = PIN_UART1_RXD,
 	.pin_tx = PIN_UART1_TXD,
 #ifdef CONFIG_SOC_GECKO_HAS_INDIVIDUAL_PIN_LOCATION
 	.loc_rx = DT_INST_1_SILABS_GECKO_UART_LOCATION_RX_0,
 	.loc_tx = DT_INST_1_SILABS_GECKO_UART_LOCATION_TX_0,
 #else
 #if DT_INST_1_SILABS_GECKO_UART_LOCATION_RX_0 \
 	!= DT_INST_1_SILABS_GECKO_UART_LOCATION_TX_0
 #error UART_1 DTS location-* properties must have identical value
 #endif
 	.loc = DT_INST_1_SILABS_GECKO_UART_LOCATION_RX_0,
 #endif
 #ifdef CONFIG_UART_INTERRUPT_DRIVEN
 	.irq_config_func = uart_gecko_config_func_1,
 #endif
 };

 static struct uart_gecko_data uart_gecko_1_data;

 DEVICE_AND_API_INIT(uart_1, DT_INST_1_SILABS_GECKO_UART_LABEL, &uart_gecko_init,
 		    &uart_gecko_1_data, &uart_gecko_1_config, PRE_KERNEL_1,
 		    CONFIG_KERNEL_INIT_PRIORITY_DEVICE, &uart_gecko_driver_api);

 #ifdef CONFIG_UART_INTERRUPT_DRIVEN
 static void uart_gecko_config_func_1(struct device *dev)
 {
 	IRQ_CONNECT(DT_INST_1_SILABS_GECKO_UART_IRQ_RX,
 		    DT_INST_1_SILABS_GECKO_UART_IRQ_RX_PRIORITY, uart_gecko_isr,
 		    DEVICE_GET(uart_1), 0);
 	IRQ_CONNECT(DT_INST_1_SILABS_GECKO_UART_IRQ_TX,
 		    DT_INST_1_SILABS_GECKO_UART_IRQ_TX_PRIORITY, uart_gecko_isr,
 		    DEVICE_GET(uart_1), 0);

 	irq_enable(DT_INST_1_SILABS_GECKO_UART_IRQ_RX);
 	irq_enable(DT_INST_1_SILABS_GECKO_UART_IRQ_TX);
 }
 #endif

 #endif /* DT_INST_1_SILABS_GECKO_UART */

 #ifdef DT_INST_0_SILABS_GECKO_USART

 #define PIN_USART0_RXD {DT_INST_0_SILABS_GECKO_USART_LOCATION_RX_1, \
 		DT_INST_0_SILABS_GECKO_USART_LOCATION_RX_2, gpioModeInput, 1}
 #define PIN_USART0_TXD {DT_INST_0_SILABS_GECKO_USART_LOCATION_TX_1, \
 		DT_INST_0_SILABS_GECKO_USART_LOCATION_TX_2, gpioModePushPull, 1}

 #ifdef CONFIG_UART_INTERRUPT_DRIVEN
 static void usart_gecko_config_func_0(struct device *dev);
 #endif

 static const struct uart_gecko_config usart_gecko_0_config = {
 	.base = (USART_TypeDef *)DT_INST_0_SILABS_GECKO_USART_BASE_ADDRESS,
 	.clock = cmuClock_USART0,
 	.baud_rate = DT_INST_0_SILABS_GECKO_USART_CURRENT_SPEED,
 	.pin_rx = PIN_USART0_RXD,
 	.pin_tx = PIN_USART0_TXD,
 #ifdef CONFIG_SOC_GECKO_HAS_INDIVIDUAL_PIN_LOCATION
 	.loc_rx = DT_INST_0_SILABS_GECKO_USART_LOCATION_RX_0,
 	.loc_tx = DT_INST_0_SILABS_GECKO_USART_LOCATION_TX_0,
 #else
 #if DT_INST_0_SILABS_GECKO_USART_LOCATION_RX_0 \
 	!= DT_INST_0_SILABS_GECKO_USART_LOCATION_TX_0
 #error USART_0 DTS location-* properties must have identical value
 #endif
 	.loc = DT_INST_0_SILABS_GECKO_USART_LOCATION_RX_0,
 #endif
 #ifdef CONFIG_UART_INTERRUPT_DRIVEN
 	.irq_config_func = usart_gecko_config_func_0,
 #endif
 };

 static struct uart_gecko_data usart_gecko_0_data;

 DEVICE_AND_API_INIT(usart_0, DT_INST_0_SILABS_GECKO_USART_LABEL,
 		    &uart_gecko_init, &usart_gecko_0_data,
 		    &usart_gecko_0_config, PRE_KERNEL_1,
 		    CONFIG_KERNEL_INIT_PRIORITY_DEVICE, &uart_gecko_driver_api);

 #ifdef CONFIG_UART_INTERRUPT_DRIVEN
 static void usart_gecko_config_func_0(struct device *dev)
 {
 	IRQ_CONNECT(DT_INST_0_SILABS_GECKO_USART_IRQ_RX,
 		    DT_INST_0_SILABS_GECKO_USART_IRQ_RX_PRIORITY,
 		    uart_gecko_isr, DEVICE_GET(usart_0), 0);
 	IRQ_CONNECT(DT_INST_0_SILABS_GECKO_USART_IRQ_TX,
 		    DT_INST_0_SILABS_GECKO_USART_IRQ_TX_PRIORITY,
 		    uart_gecko_isr, DEVICE_GET(usart_0), 0);

 	irq_enable(DT_INST_0_SILABS_GECKO_USART_IRQ_RX);
 	irq_enable(DT_INST_0_SILABS_GECKO_USART_IRQ_TX);
 }
 #endif

 #endif /* DT_INST_0_SILABS_GECKO_USART */

 #ifdef DT_INST_1_SILABS_GECKO_USART

 #define PIN_USART1_RXD {DT_INST_1_SILABS_GECKO_USART_LOCATION_RX_1, \
 		DT_INST_1_SILABS_GECKO_USART_LOCATION_RX_2, gpioModeInput, 1}
 #define PIN_USART1_TXD {DT_INST_1_SILABS_GECKO_USART_LOCATION_TX_1, \
 		DT_INST_1_SILABS_GECKO_USART_LOCATION_TX_2, gpioModePushPull, 1}

 #ifdef CONFIG_UART_INTERRUPT_DRIVEN
 static void usart_gecko_config_func_1(struct device *dev);
 #endif

 static const struct uart_gecko_config usart_gecko_1_config = {
 	.base = (USART_TypeDef *)DT_INST_1_SILABS_GECKO_USART_BASE_ADDRESS,
 	.clock = cmuClock_USART1,
 	.baud_rate = DT_INST_1_SILABS_GECKO_USART_CURRENT_SPEED,
 	.pin_rx = PIN_USART1_RXD,
 	.pin_tx = PIN_USART1_TXD,
 #ifdef CONFIG_SOC_GECKO_HAS_INDIVIDUAL_PIN_LOCATION
 	.loc_rx = DT_INST_1_SILABS_GECKO_USART_LOCATION_RX_0,
 	.loc_tx = DT_INST_1_SILABS_GECKO_USART_LOCATION_TX_0,
 #else
 #if DT_INST_1_SILABS_GECKO_USART_LOCATION_RX_0 \
 	!= DT_INST_1_SILABS_GECKO_USART_LOCATION_TX_0
 #error USART_1 DTS location-* properties must have identical value
 #endif
 	.loc = DT_INST_1_SILABS_GECKO_USART_LOCATION_RX_0,
 #endif
 #ifdef CONFIG_UART_INTERRUPT_DRIVEN
 	.irq_config_func = usart_gecko_config_func_1,
 #endif
 };

 static struct uart_gecko_data usart_gecko_1_data;

 DEVICE_AND_API_INIT(usart_1, DT_INST_1_SILABS_GECKO_USART_LABEL,
 		    &uart_gecko_init, &usart_gecko_1_data,
 		    &usart_gecko_1_config, PRE_KERNEL_1,
 		    CONFIG_KERNEL_INIT_PRIORITY_DEVICE, &uart_gecko_driver_api);

 #ifdef CONFIG_UART_INTERRUPT_DRIVEN
 static void usart_gecko_config_func_1(struct device *dev)
 {
 	IRQ_CONNECT(DT_INST_1_SILABS_GECKO_USART_IRQ_RX,
 		    DT_INST_1_SILABS_GECKO_USART_IRQ_RX_PRIORITY,
 		    uart_gecko_isr, DEVICE_GET(usart_1), 0);
 	IRQ_CONNECT(DT_INST_1_SILABS_GECKO_USART_IRQ_TX,
 		    DT_INST_1_SILABS_GECKO_USART_IRQ_TX_PRIORITY,
 		    uart_gecko_isr, DEVICE_GET(usart_1), 0);

 	irq_enable(DT_INST_1_SILABS_GECKO_USART_IRQ_RX);
 	irq_enable(DT_INST_1_SILABS_GECKO_USART_IRQ_TX);
 }
 #endif

 #endif /* DT_INST_1_SILABS_GECKO_USART */

 #ifdef DT_INST_2_SILABS_GECKO_USART

 #define PIN_USART2_RXD {DT_INST_2_SILABS_GECKO_USART_LOCATION_RX_1, \
 		DT_INST_2_SILABS_GECKO_USART_LOCATION_RX_2, gpioModeInput, 1}
 #define PIN_USART2_TXD {DT_INST_2_SILABS_GECKO_USART_LOCATION_TX_1, \
 		DT_INST_2_SILABS_GECKO_USART_LOCATION_TX_2, gpioModePushPull, 1}

 #ifdef CONFIG_UART_INTERRUPT_DRIVEN
 static void usart_gecko_config_func_2(struct device *dev);
 #endif

 static const struct uart_gecko_config usart_gecko_2_config = {
 	.base = (USART_TypeDef *)DT_INST_2_SILABS_GECKO_USART_BASE_ADDRESS,
 	.clock = cmuClock_USART2,
 	.baud_rate = DT_INST_2_SILABS_GECKO_USART_CURRENT_SPEED,
 	.pin_rx = PIN_USART2_RXD,
 	.pin_tx = PIN_USART2_TXD,
 #ifdef CONFIG_SOC_GECKO_HAS_INDIVIDUAL_PIN_LOCATION
 	.loc_rx = DT_INST_2_SILABS_GECKO_USART_LOCATION_RX_0,
 	.loc_tx = DT_INST_2_SILABS_GECKO_USART_LOCATION_TX_0,
 #else
 #if DT_INST_2_SILABS_GECKO_USART_LOCATION_RX_0 \
 	!= DT_INST_2_SILABS_GECKO_USART_LOCATION_TX_0
 #error USART_2 DTS location-* properties must have identical value
 #endif
 	.loc = DT_INST_2_SILABS_GECKO_USART_LOCATION_RX_0,
 #endif
 #ifdef CONFIG_UART_INTERRUPT_DRIVEN
 	.irq_config_func = usart_gecko_config_func_2,
 #endif
 };

 static struct uart_gecko_data usart_gecko_2_data;

 DEVICE_AND_API_INIT(usart_2, DT_INST_2_SILABS_GECKO_USART_LABEL,
 		    &uart_gecko_init, &usart_gecko_2_data,
 		    &usart_gecko_2_config, PRE_KERNEL_1,
 		    CONFIG_KERNEL_INIT_PRIORITY_DEVICE, &uart_gecko_driver_api);

 #ifdef CONFIG_UART_INTERRUPT_DRIVEN
 static void usart_gecko_config_func_2(struct device *dev)
 {
 	IRQ_CONNECT(DT_INST_2_SILABS_GECKO_USART_IRQ_RX,
 		    DT_INST_2_SILABS_GECKO_USART_IRQ_RX_PRIORITY,
 		    uart_gecko_isr, DEVICE_GET(usart_2), 0);
 	IRQ_CONNECT(DT_INST_2_SILABS_GECKO_USART_IRQ_TX,
 		    DT_INST_2_SILABS_GECKO_USART_IRQ_TX_PRIORITY,
 		    uart_gecko_isr, DEVICE_GET(usart_2), 0);

 	irq_enable(DT_INST_2_SILABS_GECKO_USART_IRQ_RX);
 	irq_enable(DT_INST_2_SILABS_GECKO_USART_IRQ_TX);
 }
 #endif

 #endif /* DT_INST_2_SILABS_GECKO_USART */

 #ifdef DT_INST_3_SILABS_GECKO_USART

 #define PIN_USART3_RXD {DT_INST_3_SILABS_GECKO_USART_LOCATION_RX_1, \
 		DT_INST_3_SILABS_GECKO_USART_LOCATION_RX_2, gpioModeInput, 1}
 #define PIN_USART3_TXD {DT_INST_3_SILABS_GECKO_USART_LOCATION_TX_1, \
 		DT_INST_3_SILABS_GECKO_USART_LOCATION_TX_2, gpioModePushPull, 1}

 #ifdef CONFIG_UART_INTERRUPT_DRIVEN
 static void usart_gecko_config_func_3(struct device *dev);
 #endif

 static const struct uart_gecko_config usart_gecko_3_config = {
 	.base = (USART_TypeDef *)DT_INST_3_SILABS_GECKO_USART_BASE_ADDRESS,
 	.clock = cmuClock_USART3,
 	.baud_rate = DT_INST_3_SILABS_GECKO_USART_CURRENT_SPEED,
 	.pin_rx = PIN_USART3_RXD,
 	.pin_tx = PIN_USART3_TXD,
 #ifdef CONFIG_SOC_GECKO_HAS_INDIVIDUAL_PIN_LOCATION
 	.loc_rx = DT_INST_3_SILABS_GECKO_USART_LOCATION_RX_0,
 	.loc_tx = DT_INST_3_SILABS_GECKO_USART_LOCATION_TX_0,
 #else
 #if DT_INST_3_SILABS_GECKO_USART_LOCATION_RX_0 \
 	!= DT_INST_3_SILABS_GECKO_USART_LOCATION_TX_0
 #error USART_3 DTS location-* properties must have identical value
 #endif
 	.loc = DT_INST_3_SILABS_GECKO_USART_LOCATION_RX_0,
 #endif
 #ifdef CONFIG_UART_INTERRUPT_DRIVEN
 	.irq_config_func = usart_gecko_config_func_3,
 #endif
 };

 static struct uart_gecko_data usart_gecko_3_data;

 DEVICE_AND_API_INIT(usart_3, DT_INST_3_SILABS_GECKO_USART_LABEL,
 		    &uart_gecko_init, &usart_gecko_3_data,
 		    &usart_gecko_3_config, PRE_KERNEL_1,
 		    CONFIG_KERNEL_INIT_PRIORITY_DEVICE, &uart_gecko_driver_api);

 #ifdef CONFIG_UART_INTERRUPT_DRIVEN
 static void usart_gecko_config_func_3(struct device *dev)
 {
 	IRQ_CONNECT(DT_INST_3_SILABS_GECKO_USART_IRQ_RX,
 		    DT_INST_3_SILABS_GECKO_USART_IRQ_RX_PRIORITY,
 		    uart_gecko_isr, DEVICE_GET(usart_3), 0);
 	IRQ_CONNECT(DT_INST_3_SILABS_GECKO_USART_IRQ_TX,
 		    DT_INST_3_SILABS_GECKO_USART_IRQ_TX_PRIORITY,
 		    uart_gecko_isr, DEVICE_GET(usart_3), 0);

 	irq_enable(DT_INST_3_SILABS_GECKO_USART_IRQ_RX);
 	irq_enable(DT_INST_3_SILABS_GECKO_USART_IRQ_TX);
 }
 #endif

 #endif /* DT_INST_3_SILABS_GECKO_USART */
	/*
	* Copyright (c) 2017, Christian Taedcke
	*
	* SPDX-License-Identifier: Apache-2.0
	*/

	#include <errno.h>
	#include <drivers/uart.h>
	#include <em_usart.h>
	#include <em_gpio.h>
	#include <em_cmu.h>
	#include <soc.h>

	struct uart_gecko_config {
	USART_TypeDef *base;
	CMU_Clock_TypeDef clock;
	u32_t baud_rate;
	#ifdef CONFIG_UART_INTERRUPT_DRIVEN
	void (irq_config_func)(struct device dev);
	#endif
	struct soc_gpio_pin pin_rx;
	struct soc_gpio_pin pin_tx;
	#ifdef CONFIG_SOC_GECKO_HAS_INDIVIDUAL_PIN_LOCATION
	u8_t loc_rx;
	u8_t loc_tx;
	#else
	u8_t loc;
	#endif
	};

	struct uart_gecko_data {
	#ifdef CONFIG_UART_INTERRUPT_DRIVEN
	uart_irq_callback_user_data_t callback;
	void *cb_data;
	#endif
	};

	static int uart_gecko_poll_in(struct device dev, unsigned char c)
	{
	const struct uart_gecko_config *config = dev->config->config_info;
	u32_t flags = USART_StatusGet(config->base);

	if (flags & USART_STATUS_RXDATAV) {
	*c = USART_Rx(config->base);
	return 0;
	}

	return -1;
	}

	static void uart_gecko_poll_out(struct device *dev, unsigned char c)
	{
	const struct uart_gecko_config *config = dev->config->config_info;

	USART_Tx(config->base, c);
	}

	static int uart_gecko_err_check(struct device *dev)
	{
	const struct uart_gecko_config *config = dev->config->config_info;
	u32_t flags = USART_IntGet(config->base);
	int err = 0;

	if (flags & USART_IF_RXOF) {
	err \|= UART_ERROR_OVERRUN;
	}

	if (flags & USART_IF_PERR) {
	err \|= UART_ERROR_PARITY;
	}

	if (flags & USART_IF_FERR) {
	err \|= UART_ERROR_FRAMING;
	}

	USART_IntClear(config->base, USART_IF_RXOF \|
	USART_IF_PERR \|
	USART_IF_FERR);

	return err;
	}

	#ifdef CONFIG_UART_INTERRUPT_DRIVEN
	static int uart_gecko_fifo_fill(struct device dev, const u8_t tx_data,
	int len)
	{
	const struct uart_gecko_config *config = dev->config->config_info;
	u8_t num_tx = 0U;

	while ((len - num_tx > 0) &&
	(config->base->STATUS & USART_STATUS_TXBL)) {

	config->base->TXDATA = (u32_t)tx_data[num_tx++];
	}

	return num_tx;
	}

	static int uart_gecko_fifo_read(struct device dev, u8_t rx_data,
	const int len)
	{
	const struct uart_gecko_config *config = dev->config->config_info;
	u8_t num_rx = 0U;

	while ((len - num_rx > 0) &&
	(config->base->STATUS & USART_STATUS_RXDATAV)) {

	rx_data[num_rx++] = (u8_t)config->base->RXDATA;
	}

	return num_rx;
	}

	static void uart_gecko_irq_tx_enable(struct device *dev)
	{
	const struct uart_gecko_config *config = dev->config->config_info;
	u32_t mask = USART_IEN_TXBL \| USART_IEN_TXC;

	USART_IntEnable(config->base, mask);
	}

	static void uart_gecko_irq_tx_disable(struct device *dev)
	{
	const struct uart_gecko_config *config = dev->config->config_info;
	u32_t mask = USART_IEN_TXBL \| USART_IEN_TXC;

	USART_IntDisable(config->base, mask);
	}

	static int uart_gecko_irq_tx_complete(struct device *dev)
	{
	const struct uart_gecko_config *config = dev->config->config_info;
	u32_t flags = USART_IntGet(config->base);

	USART_IntClear(config->base, USART_IF_TXC);

	return (flags & USART_IF_TXC) != 0U;
	}

	static int uart_gecko_irq_tx_ready(struct device *dev)
	{
	const struct uart_gecko_config *config = dev->config->config_info;
	u32_t flags = USART_IntGet(config->base);

	return (flags & USART_IF_TXBL) != 0U;
	}

	static void uart_gecko_irq_rx_enable(struct device *dev)
	{
	const struct uart_gecko_config *config = dev->config->config_info;
	u32_t mask = USART_IEN_RXDATAV;

	USART_IntEnable(config->base, mask);
	}

	static void uart_gecko_irq_rx_disable(struct device *dev)
	{
	const struct uart_gecko_config *config = dev->config->config_info;
	u32_t mask = USART_IEN_RXDATAV;

	USART_IntDisable(config->base, mask);
	}

	static int uart_gecko_irq_rx_full(struct device *dev)
	{
	const struct uart_gecko_config *config = dev->config->config_info;
	u32_t flags = USART_IntGet(config->base);

	return (flags & USART_IF_RXDATAV) != 0U;
	}

	static int uart_gecko_irq_rx_ready(struct device *dev)
	{
	const struct uart_gecko_config *config = dev->config->config_info;
	u32_t mask = USART_IEN_RXDATAV;

	return (config->base->IEN & mask)
	&& uart_gecko_irq_rx_full(dev);
	}

	static void uart_gecko_irq_err_enable(struct device *dev)
	{
	const struct uart_gecko_config *config = dev->config->config_info;

	USART_IntEnable(config->base, USART_IF_RXOF \|
	USART_IF_PERR \|
	USART_IF_FERR);
	}

	static void uart_gecko_irq_err_disable(struct device *dev)
	{
	const struct uart_gecko_config *config = dev->config->config_info;

	USART_IntDisable(config->base, USART_IF_RXOF \|
	USART_IF_PERR \|
	USART_IF_FERR);
	}

	static int uart_gecko_irq_is_pending(struct device *dev)
	{
	return uart_gecko_irq_tx_ready(dev) \|\| uart_gecko_irq_rx_ready(dev);
	}

	static int uart_gecko_irq_update(struct device *dev)
	{
	return 1;
	}

	static void uart_gecko_irq_callback_set(struct device *dev,
	uart_irq_callback_user_data_t cb,
	void *cb_data)
	{
	struct uart_gecko_data *data = dev->driver_data;

	data->callback = cb;
	data->cb_data = cb_data;
	}

	static void uart_gecko_isr(void *arg)
	{
	struct device *dev = arg;
	struct uart_gecko_data *data = dev->driver_data;

	if (data->callback) {
	data->callback(data->cb_data);
	}
	}
	#endif /* CONFIG_UART_INTERRUPT_DRIVEN */

	static void uart_gecko_init_pins(struct device *dev)
	{
	const struct uart_gecko_config *config = dev->config->config_info;

	soc_gpio_configure(&config->pin_rx);
	soc_gpio_configure(&config->pin_tx);
	#ifdef CONFIG_SOC_GECKO_HAS_INDIVIDUAL_PIN_LOCATION
	config->base->ROUTEPEN = USART_ROUTEPEN_RXPEN \| USART_ROUTEPEN_TXPEN;
	config->base->ROUTELOC0 =
	(config->loc_tx << _USART_ROUTELOC0_TXLOC_SHIFT) \|
	(config->loc_rx << _USART_ROUTELOC0_RXLOC_SHIFT);
	config->base->ROUTELOC1 = _USART_ROUTELOC1_RESETVALUE;
	#else
	config->base->ROUTE = USART_ROUTE_RXPEN \| USART_ROUTE_TXPEN
	\| (config->loc << 8);
	#endif
	}

	static int uart_gecko_init(struct device *dev)
	{
	const struct uart_gecko_config *config = dev->config->config_info;
	USART_InitAsync_TypeDef usartInit = USART_INITASYNC_DEFAULT;

	/* The peripheral and gpio clock are already enabled from soc and gpio
	* driver
	*/

	usartInit.baudrate = config->baud_rate;

	/* Enable USART clock */
	CMU_ClockEnable(config->clock, true);

	/* Init USART */
	USART_InitAsync(config->base, &usartInit);

	/* Initialize USART pins */
	uart_gecko_init_pins(dev);

	#ifdef CONFIG_UART_INTERRUPT_DRIVEN
	config->irq_config_func(dev);
	#endif

	return 0;
	}

	static const struct uart_driver_api uart_gecko_driver_api = {
	.poll_in = uart_gecko_poll_in,
	.poll_out = uart_gecko_poll_out,
	.err_check = uart_gecko_err_check,
	#ifdef CONFIG_UART_INTERRUPT_DRIVEN
	.fifo_fill = uart_gecko_fifo_fill,
	.fifo_read = uart_gecko_fifo_read,
	.irq_tx_enable = uart_gecko_irq_tx_enable,
	.irq_tx_disable = uart_gecko_irq_tx_disable,
	.irq_tx_complete = uart_gecko_irq_tx_complete,
	.irq_tx_ready = uart_gecko_irq_tx_ready,
	.irq_rx_enable = uart_gecko_irq_rx_enable,
	.irq_rx_disable = uart_gecko_irq_rx_disable,
	.irq_rx_ready = uart_gecko_irq_rx_ready,
	.irq_err_enable = uart_gecko_irq_err_enable,
	.irq_err_disable = uart_gecko_irq_err_disable,
	.irq_is_pending = uart_gecko_irq_is_pending,
	.irq_update = uart_gecko_irq_update,
	.irq_callback_set = uart_gecko_irq_callback_set,
	#endif
	};

	#ifdef DT_INST_0_SILABS_GECKO_UART

	#define PIN_UART0_RXD {DT_INST_0_SILABS_GECKO_UART_LOCATION_RX_1, \
	DT_INST_0_SILABS_GECKO_UART_LOCATION_RX_2, gpioModeInput, 1}
	#define PIN_UART0_TXD {DT_INST_0_SILABS_GECKO_UART_LOCATION_TX_1, \
	DT_INST_0_SILABS_GECKO_UART_LOCATION_TX_2, gpioModePushPull, 1}

	#ifdef CONFIG_UART_INTERRUPT_DRIVEN
	static void uart_gecko_config_func_0(struct device *dev);
	#endif

	static const struct uart_gecko_config uart_gecko_0_config = {
	.base = (USART_TypeDef *)DT_INST_0_SILABS_GECKO_UART_BASE_ADDRESS,
	.clock = cmuClock_UART0,
	.baud_rate = DT_INST_0_SILABS_GECKO_UART_CURRENT_SPEED,
	.pin_rx = PIN_UART0_RXD,
	.pin_tx = PIN_UART0_TXD,
	#ifdef CONFIG_SOC_GECKO_HAS_INDIVIDUAL_PIN_LOCATION
	.loc_rx = DT_INST_0_SILABS_GECKO_UART_LOCATION_RX_0,
	.loc_tx = DT_INST_0_SILABS_GECKO_UART_LOCATION_TX_0,
	#else
	#if DT_INST_0_SILABS_GECKO_UART_LOCATION_RX_0 \
	!= DT_INST_0_SILABS_GECKO_UART_LOCATION_TX_0
	#error UART_0 DTS location-* properties must have identical value
	#endif
	.loc = DT_INST_0_SILABS_GECKO_UART_LOCATION_RX_0,
	#endif
	#ifdef CONFIG_UART_INTERRUPT_DRIVEN
	.irq_config_func = uart_gecko_config_func_0,
	#endif
	};

	static struct uart_gecko_data uart_gecko_0_data;

	DEVICE_AND_API_INIT(uart_0, DT_INST_0_SILABS_GECKO_UART_LABEL, &uart_gecko_init,
	&uart_gecko_0_data, &uart_gecko_0_config, PRE_KERNEL_1,
	CONFIG_KERNEL_INIT_PRIORITY_DEVICE, &uart_gecko_driver_api);

	#ifdef CONFIG_UART_INTERRUPT_DRIVEN
	static void uart_gecko_config_func_0(struct device *dev)
	{
	IRQ_CONNECT(DT_INST_0_SILABS_GECKO_UART_IRQ_RX,
	DT_INST_0_SILABS_GECKO_UART_IRQ_RX_PRIORITY, uart_gecko_isr,
	DEVICE_GET(uart_0), 0);
	IRQ_CONNECT(DT_INST_0_SILABS_GECKO_UART_IRQ_TX,
	DT_INST_0_SILABS_GECKO_UART_IRQ_TX_PRIORITY, uart_gecko_isr,
	DEVICE_GET(uart_0), 0);

	irq_enable(DT_INST_0_SILABS_GECKO_UART_IRQ_RX);
	irq_enable(DT_INST_0_SILABS_GECKO_UART_IRQ_TX);
	}
	#endif

	#endif /* DT_INST_0_SILABS_GECKO_UART */

	#ifdef DT_INST_1_SILABS_GECKO_UART

	#define PIN_UART1_RXD {DT_INST_1_SILABS_GECKO_UART_LOCATION_RX_1, \
	DT_INST_1_SILABS_GECKO_UART_LOCATION_RX_2, gpioModeInput, 1}
	#define PIN_UART1_TXD {DT_INST_1_SILABS_GECKO_UART_LOCATION_TX_1, \
	DT_INST_1_SILABS_GECKO_UART_LOCATION_TX_2, gpioModePushPull, 1}

	#ifdef CONFIG_UART_INTERRUPT_DRIVEN
	static void uart_gecko_config_func_1(struct device *dev);
	#endif

	static const struct uart_gecko_config uart_gecko_1_config = {
	.base = (USART_TypeDef *)DT_INST_1_SILABS_GECKO_UART_BASE_ADDRESS,
	.clock = cmuClock_UART1,
	.baud_rate = DT_INST_1_SILABS_GECKO_UART_CURRENT_SPEED,
	.pin_rx = PIN_UART1_RXD,
	.pin_tx = PIN_UART1_TXD,
	#ifdef CONFIG_SOC_GECKO_HAS_INDIVIDUAL_PIN_LOCATION
	.loc_rx = DT_INST_1_SILABS_GECKO_UART_LOCATION_RX_0,
	.loc_tx = DT_INST_1_SILABS_GECKO_UART_LOCATION_TX_0,
	#else
	#if DT_INST_1_SILABS_GECKO_UART_LOCATION_RX_0 \
	!= DT_INST_1_SILABS_GECKO_UART_LOCATION_TX_0
	#error UART_1 DTS location-* properties must have identical value
	#endif
	.loc = DT_INST_1_SILABS_GECKO_UART_LOCATION_RX_0,
	#endif
	#ifdef CONFIG_UART_INTERRUPT_DRIVEN
	.irq_config_func = uart_gecko_config_func_1,
	#endif
	};

	static struct uart_gecko_data uart_gecko_1_data;

	DEVICE_AND_API_INIT(uart_1, DT_INST_1_SILABS_GECKO_UART_LABEL, &uart_gecko_init,
	&uart_gecko_1_data, &uart_gecko_1_config, PRE_KERNEL_1,
	CONFIG_KERNEL_INIT_PRIORITY_DEVICE, &uart_gecko_driver_api);

	#ifdef CONFIG_UART_INTERRUPT_DRIVEN
	static void uart_gecko_config_func_1(struct device *dev)
	{
	IRQ_CONNECT(DT_INST_1_SILABS_GECKO_UART_IRQ_RX,
	DT_INST_1_SILABS_GECKO_UART_IRQ_RX_PRIORITY, uart_gecko_isr,
	DEVICE_GET(uart_1), 0);
	IRQ_CONNECT(DT_INST_1_SILABS_GECKO_UART_IRQ_TX,
	DT_INST_1_SILABS_GECKO_UART_IRQ_TX_PRIORITY, uart_gecko_isr,
	DEVICE_GET(uart_1), 0);

	irq_enable(DT_INST_1_SILABS_GECKO_UART_IRQ_RX);
	irq_enable(DT_INST_1_SILABS_GECKO_UART_IRQ_TX);
	}
	#endif

	#endif /* DT_INST_1_SILABS_GECKO_UART */

	#ifdef DT_INST_0_SILABS_GECKO_USART

	#define PIN_USART0_RXD {DT_INST_0_SILABS_GECKO_USART_LOCATION_RX_1, \
	DT_INST_0_SILABS_GECKO_USART_LOCATION_RX_2, gpioModeInput, 1}
	#define PIN_USART0_TXD {DT_INST_0_SILABS_GECKO_USART_LOCATION_TX_1, \
	DT_INST_0_SILABS_GECKO_USART_LOCATION_TX_2, gpioModePushPull, 1}

	#ifdef CONFIG_UART_INTERRUPT_DRIVEN
	static void usart_gecko_config_func_0(struct device *dev);
	#endif

	static const struct uart_gecko_config usart_gecko_0_config = {
	.base = (USART_TypeDef *)DT_INST_0_SILABS_GECKO_USART_BASE_ADDRESS,
	.clock = cmuClock_USART0,
	.baud_rate = DT_INST_0_SILABS_GECKO_USART_CURRENT_SPEED,
	.pin_rx = PIN_USART0_RXD,
	.pin_tx = PIN_USART0_TXD,
	#ifdef CONFIG_SOC_GECKO_HAS_INDIVIDUAL_PIN_LOCATION
	.loc_rx = DT_INST_0_SILABS_GECKO_USART_LOCATION_RX_0,
	.loc_tx = DT_INST_0_SILABS_GECKO_USART_LOCATION_TX_0,
	#else
	#if DT_INST_0_SILABS_GECKO_USART_LOCATION_RX_0 \
	!= DT_INST_0_SILABS_GECKO_USART_LOCATION_TX_0
	#error USART_0 DTS location-* properties must have identical value
	#endif
	.loc = DT_INST_0_SILABS_GECKO_USART_LOCATION_RX_0,
	#endif
	#ifdef CONFIG_UART_INTERRUPT_DRIVEN
	.irq_config_func = usart_gecko_config_func_0,
	#endif
	};

	static struct uart_gecko_data usart_gecko_0_data;

	DEVICE_AND_API_INIT(usart_0, DT_INST_0_SILABS_GECKO_USART_LABEL,
	&uart_gecko_init, &usart_gecko_0_data,
	&usart_gecko_0_config, PRE_KERNEL_1,
	CONFIG_KERNEL_INIT_PRIORITY_DEVICE, &uart_gecko_driver_api);

	#ifdef CONFIG_UART_INTERRUPT_DRIVEN
	static void usart_gecko_config_func_0(struct device *dev)
	{
	IRQ_CONNECT(DT_INST_0_SILABS_GECKO_USART_IRQ_RX,
	DT_INST_0_SILABS_GECKO_USART_IRQ_RX_PRIORITY,
	uart_gecko_isr, DEVICE_GET(usart_0), 0);
	IRQ_CONNECT(DT_INST_0_SILABS_GECKO_USART_IRQ_TX,
	DT_INST_0_SILABS_GECKO_USART_IRQ_TX_PRIORITY,
	uart_gecko_isr, DEVICE_GET(usart_0), 0);

	irq_enable(DT_INST_0_SILABS_GECKO_USART_IRQ_RX);
	irq_enable(DT_INST_0_SILABS_GECKO_USART_IRQ_TX);
	}
	#endif

	#endif /* DT_INST_0_SILABS_GECKO_USART */

	#ifdef DT_INST_1_SILABS_GECKO_USART

	#define PIN_USART1_RXD {DT_INST_1_SILABS_GECKO_USART_LOCATION_RX_1, \
	DT_INST_1_SILABS_GECKO_USART_LOCATION_RX_2, gpioModeInput, 1}
	#define PIN_USART1_TXD {DT_INST_1_SILABS_GECKO_USART_LOCATION_TX_1, \
	DT_INST_1_SILABS_GECKO_USART_LOCATION_TX_2, gpioModePushPull, 1}

	#ifdef CONFIG_UART_INTERRUPT_DRIVEN
	static void usart_gecko_config_func_1(struct device *dev);
	#endif

	static const struct uart_gecko_config usart_gecko_1_config = {
	.base = (USART_TypeDef *)DT_INST_1_SILABS_GECKO_USART_BASE_ADDRESS,
	.clock = cmuClock_USART1,
	.baud_rate = DT_INST_1_SILABS_GECKO_USART_CURRENT_SPEED,
	.pin_rx = PIN_USART1_RXD,
	.pin_tx = PIN_USART1_TXD,
	#ifdef CONFIG_SOC_GECKO_HAS_INDIVIDUAL_PIN_LOCATION
	.loc_rx = DT_INST_1_SILABS_GECKO_USART_LOCATION_RX_0,
	.loc_tx = DT_INST_1_SILABS_GECKO_USART_LOCATION_TX_0,
	#else
	#if DT_INST_1_SILABS_GECKO_USART_LOCATION_RX_0 \
	!= DT_INST_1_SILABS_GECKO_USART_LOCATION_TX_0
	#error USART_1 DTS location-* properties must have identical value
	#endif
	.loc = DT_INST_1_SILABS_GECKO_USART_LOCATION_RX_0,
	#endif
	#ifdef CONFIG_UART_INTERRUPT_DRIVEN
	.irq_config_func = usart_gecko_config_func_1,
	#endif
	};

	static struct uart_gecko_data usart_gecko_1_data;

	DEVICE_AND_API_INIT(usart_1, DT_INST_1_SILABS_GECKO_USART_LABEL,
	&uart_gecko_init, &usart_gecko_1_data,
	&usart_gecko_1_config, PRE_KERNEL_1,
	CONFIG_KERNEL_INIT_PRIORITY_DEVICE, &uart_gecko_driver_api);

	#ifdef CONFIG_UART_INTERRUPT_DRIVEN
	static void usart_gecko_config_func_1(struct device *dev)
	{
	IRQ_CONNECT(DT_INST_1_SILABS_GECKO_USART_IRQ_RX,
	DT_INST_1_SILABS_GECKO_USART_IRQ_RX_PRIORITY,
	uart_gecko_isr, DEVICE_GET(usart_1), 0);
	IRQ_CONNECT(DT_INST_1_SILABS_GECKO_USART_IRQ_TX,
	DT_INST_1_SILABS_GECKO_USART_IRQ_TX_PRIORITY,
	uart_gecko_isr, DEVICE_GET(usart_1), 0);

	irq_enable(DT_INST_1_SILABS_GECKO_USART_IRQ_RX);
	irq_enable(DT_INST_1_SILABS_GECKO_USART_IRQ_TX);
	}
	#endif

	#endif /* DT_INST_1_SILABS_GECKO_USART */

	#ifdef DT_INST_2_SILABS_GECKO_USART

	#define PIN_USART2_RXD {DT_INST_2_SILABS_GECKO_USART_LOCATION_RX_1, \
	DT_INST_2_SILABS_GECKO_USART_LOCATION_RX_2, gpioModeInput, 1}
	#define PIN_USART2_TXD {DT_INST_2_SILABS_GECKO_USART_LOCATION_TX_1, \
	DT_INST_2_SILABS_GECKO_USART_LOCATION_TX_2, gpioModePushPull, 1}

	#ifdef CONFIG_UART_INTERRUPT_DRIVEN
	static void usart_gecko_config_func_2(struct device *dev);
	#endif

	static const struct uart_gecko_config usart_gecko_2_config = {
	.base = (USART_TypeDef *)DT_INST_2_SILABS_GECKO_USART_BASE_ADDRESS,
	.clock = cmuClock_USART2,
	.baud_rate = DT_INST_2_SILABS_GECKO_USART_CURRENT_SPEED,
	.pin_rx = PIN_USART2_RXD,
	.pin_tx = PIN_USART2_TXD,
	#ifdef CONFIG_SOC_GECKO_HAS_INDIVIDUAL_PIN_LOCATION
	.loc_rx = DT_INST_2_SILABS_GECKO_USART_LOCATION_RX_0,
	.loc_tx = DT_INST_2_SILABS_GECKO_USART_LOCATION_TX_0,
	#else
	#if DT_INST_2_SILABS_GECKO_USART_LOCATION_RX_0 \
	!= DT_INST_2_SILABS_GECKO_USART_LOCATION_TX_0
	#error USART_2 DTS location-* properties must have identical value
	#endif
	.loc = DT_INST_2_SILABS_GECKO_USART_LOCATION_RX_0,
	#endif
	#ifdef CONFIG_UART_INTERRUPT_DRIVEN
	.irq_config_func = usart_gecko_config_func_2,
	#endif
	};

	static struct uart_gecko_data usart_gecko_2_data;

	DEVICE_AND_API_INIT(usart_2, DT_INST_2_SILABS_GECKO_USART_LABEL,
	&uart_gecko_init, &usart_gecko_2_data,
	&usart_gecko_2_config, PRE_KERNEL_1,
	CONFIG_KERNEL_INIT_PRIORITY_DEVICE, &uart_gecko_driver_api);

	#ifdef CONFIG_UART_INTERRUPT_DRIVEN
	static void usart_gecko_config_func_2(struct device *dev)
	{
	IRQ_CONNECT(DT_INST_2_SILABS_GECKO_USART_IRQ_RX,
	DT_INST_2_SILABS_GECKO_USART_IRQ_RX_PRIORITY,
	uart_gecko_isr, DEVICE_GET(usart_2), 0);
	IRQ_CONNECT(DT_INST_2_SILABS_GECKO_USART_IRQ_TX,
	DT_INST_2_SILABS_GECKO_USART_IRQ_TX_PRIORITY,
	uart_gecko_isr, DEVICE_GET(usart_2), 0);

	irq_enable(DT_INST_2_SILABS_GECKO_USART_IRQ_RX);
	irq_enable(DT_INST_2_SILABS_GECKO_USART_IRQ_TX);
	}
	#endif

	#endif /* DT_INST_2_SILABS_GECKO_USART */

	#ifdef DT_INST_3_SILABS_GECKO_USART

	#define PIN_USART3_RXD {DT_INST_3_SILABS_GECKO_USART_LOCATION_RX_1, \
	DT_INST_3_SILABS_GECKO_USART_LOCATION_RX_2, gpioModeInput, 1}
	#define PIN_USART3_TXD {DT_INST_3_SILABS_GECKO_USART_LOCATION_TX_1, \
	DT_INST_3_SILABS_GECKO_USART_LOCATION_TX_2, gpioModePushPull, 1}

	#ifdef CONFIG_UART_INTERRUPT_DRIVEN
	static void usart_gecko_config_func_3(struct device *dev);
	#endif

	static const struct uart_gecko_config usart_gecko_3_config = {
	.base = (USART_TypeDef *)DT_INST_3_SILABS_GECKO_USART_BASE_ADDRESS,
	.clock = cmuClock_USART3,
	.baud_rate = DT_INST_3_SILABS_GECKO_USART_CURRENT_SPEED,
	.pin_rx = PIN_USART3_RXD,
	.pin_tx = PIN_USART3_TXD,
	#ifdef CONFIG_SOC_GECKO_HAS_INDIVIDUAL_PIN_LOCATION
	.loc_rx = DT_INST_3_SILABS_GECKO_USART_LOCATION_RX_0,
	.loc_tx = DT_INST_3_SILABS_GECKO_USART_LOCATION_TX_0,
	#else
	#if DT_INST_3_SILABS_GECKO_USART_LOCATION_RX_0 \
	!= DT_INST_3_SILABS_GECKO_USART_LOCATION_TX_0
	#error USART_3 DTS location-* properties must have identical value
	#endif
	.loc = DT_INST_3_SILABS_GECKO_USART_LOCATION_RX_0,
	#endif
	#ifdef CONFIG_UART_INTERRUPT_DRIVEN
	.irq_config_func = usart_gecko_config_func_3,
	#endif
	};

	static struct uart_gecko_data usart_gecko_3_data;

	DEVICE_AND_API_INIT(usart_3, DT_INST_3_SILABS_GECKO_USART_LABEL,
	&uart_gecko_init, &usart_gecko_3_data,
	&usart_gecko_3_config, PRE_KERNEL_1,
	CONFIG_KERNEL_INIT_PRIORITY_DEVICE, &uart_gecko_driver_api);

	#ifdef CONFIG_UART_INTERRUPT_DRIVEN
	static void usart_gecko_config_func_3(struct device *dev)
	{
	IRQ_CONNECT(DT_INST_3_SILABS_GECKO_USART_IRQ_RX,
	DT_INST_3_SILABS_GECKO_USART_IRQ_RX_PRIORITY,
	uart_gecko_isr, DEVICE_GET(usart_3), 0);
	IRQ_CONNECT(DT_INST_3_SILABS_GECKO_USART_IRQ_TX,
	DT_INST_3_SILABS_GECKO_USART_IRQ_TX_PRIORITY,
	uart_gecko_isr, DEVICE_GET(usart_3), 0);

	irq_enable(DT_INST_3_SILABS_GECKO_USART_IRQ_RX);
	irq_enable(DT_INST_3_SILABS_GECKO_USART_IRQ_TX);
	}
	#endif

	#endif /* DT_INST_3_SILABS_GECKO_USART */