doc/kernel/nanokernel/nanokernel_interrupts.rst - third_party/github/zephyrproject-rtos/zephyr - Git at Google

 .. _nanokernel_interrupts:

 Interrupt Services
 ##################

 Concepts
 ********

 :abbr:`ISRs (Interrupt Service Routines)` are execution threads
 that run in response to a hardware or software interrupt.
 They are used to preempt the execution of the
 task or fiber running at the time of the interrupt,
 allowing the response to occur with very low overhead.
 When an ISR completes its normal task and fiber execution resumes.

 Any number of ISRs can be utilized in a Zephyr project, subject to
 any hardware constraints imposed by the underlying hardware.
 Each ISR has the following properties:

 * The :abbr:`IRQ (Interrupt ReQuest)` signal that triggers the ISR.
 * The priority level associated with the IRQ.
 * The address of the function that is invoked to handle the interrupt.
 * The argument value that is passed to that function.

 An :abbr:`IDT (Interrupt Descriptor Table)` is used to associate a given interrupt
 source with a given ISR.
 Only a single ISR can be associated with a specific IRQ at any given time.
 An ISR can be incorporated into the IDT when the Zephyr project is built
 (a "static ISR") or bound to the IDT when the system is up and running
 (a "dynamic ISR").

 Multiple ISRs can utilize the same function to process interrupts,
 allowing a single function to service a device that generates
 multiple types of interrupts or to service multiple devices
 (usually of the same type). The argument value passed to an ISR's function
 can be used to allow the function to determine which interrupt has been
 signaled.

 The Zephyr kernel provides a default ISR for all unused IDT entries. This ISR
 generates a fatal system error if an unexpected interrupt is signaled.

 The kernel supports interrupt nesting. This allows an ISR to be preempted
 in mid-execution if a higher priority interrupt is signaled. The lower
 priority ISR resumes execution once the higher priority ISR has completed
 its processing.

 The kernel allows a task or fiber to temporarily lock out the execution
 of ISRs, either individually or collectively, should the need arise.
 The collective lock can be applied repeatedly; that is, the lock can
 be applied when it is already in effect. The collective lock must be
 unlocked an equal number of times before interrupts are again processed
 by the kernel.

 Purpose
 *******

 Use an ISR to perform interrupt processing that requires a very rapid
 response, and which can be done quickly and without blocking.

 .. note::

    Interrupt processing that is time consuming, or which involves blocking,
    should be handed off to a fiber or task. See `Offloading ISR Work`_ for
    a description of various techniques that can be used in a Zephyr project.

 Installing an ISR
 *****************

 Use one of the following procedures to install an ISR:

 * `Installing a Static ISR`_
 * `Installing a Dynamic ISR`_

 Installing a Static ISR
 =======================

 Use a static ISR to register an interrupt handler when the interrupt
 parameters are known during the build time and the device is always
 present in the system.

 .. note::

    There is no API method to uninstall a static ISR; however, it is
    possible to replace it by installing a dynamic ISR.

 Prerequisites
 -------------

 * Ensure that the platform used by the project supports static ISRs.

 Example
 -------

 .. code-block:: c

    #define MY_DEV_IRQ  24       /* device uses IRQ 24 */
    #define MY_DEV_PRIO  2       /* device uses interrupt priority 2 */
    /* argument passed to my_isr(), in this case a pointer to the device */
    #define MY_ISR_ARG  DEVICE_GET(my_device)
    #define MY_IRQ_FLAGS 0       /* IRQ flags. Unused on non-x86 */

    void my_isr(void *arg)
    {
       ... /* ISR code */
    }

    void my_isr_installer(void)
    {
       ...
       IRQ_CONNECT(MY_DEV_IRQ, MY_DEV_PRIO, my_isr, MY_ISR_ARG, MY_IRQ_FLAGS);
       irq_enable(MY_DEV_IRQ);            /* enable IRQ */
       ...
    }

 Installing a Dynamic ISR
 ========================

 Use a dynamic ISR to register an interrupt handler when the interrupt
 parameters can be found out only at runtime, or when a device is not always
 present in the system.

 Prerequisites
 -------------

 * Ensure that the platform used by the project supports dynamic ISRs.

 * (x86 only) Set the :option:`NUM_DYNAMIC_STUBS` configuration option
   to specify the maximum number of dynamic ISRs allowed in the project.

 * (ARC & ARM only) Enable the :option:`SW_ISR_TABLE_DYNAMIC` so that
   interrupts may be connected at runtime.

 Example
 -------

 This is an example of a dynamic interrupt for x86:

 .. code-block:: c

    #define MY_DEV_IRQ 24        /* device uses IRQ 24 */
    #define MY_DEV_PRIO 2        /* device uses interrupt priority 2 */
    #define MY_ISR_ARG 17        /* argument passed to my_isr() */
    /* IRQ flags. Interrupt is triggered by low level signal */
    #define MY_IRQ_FLAGS (IOAPIC_LEVEL | IOAPIC_LOW)

    void my_isr(void *arg)
    {
       ... /* ISR code */
    }

    void my_isr_installer(void)
    {
        ...
        irq_connect_dynamic(MY_DEV_IRQ, MY_DEV_PRIO, my_isr, MY_ISR_ARG,
                            MY_IRQ_FLAGS);
        ...
        irq_enable(MY_DEV_IRQ);
        ...
    }

 Working with Interrupts
 ***********************

 Use the following:

 * `Offloading ISR Work`_
 * `IDT Security`_

 Offloading ISR Work
 ===================

 Interrupt service routines should generally be kept short
 to ensure predictable system operation.
 In situations where time consuming processing is required
 an ISR can quickly restore the kernel's ability to respond
 to other interrupts by offloading some or all of the interrupt-related
 processing work to a fiber or task.

 Zephyr OS provides a variety of mechanisms to allow an ISR to offload work
 to a fiber or task.

 1. An ISR can signal a helper fiber (or task) to do interrupt-related work
    using a nanokernel object, such as a FIFO, LIFO, or semaphore.
    The :c:func:`nano_isr_XXX()` APIs should be used to notify the helper fiber
    (or task) that work is available for it.

    See :ref:`fiber_services`.

 2. An ISR can signal the microkernel server fiber to do interrupt-related
    work by sending an event that has an associated event handler.

    See :ref:`microkernel_events`.

 3. An ISR can signal a helper task to do interrupt-related work
    by sending an event that the helper task detects.

    See :ref:`microkernel_events`.

 4. An ISR can signal a helper task to do interrupt-related work.
    by giving a semaphore that the helper task takes.

    See :ref:`microkernel_semaphores`.

 5. A kernel-supplied ISR can signal a helper task to do interrupt-related work
    using a task IRQ that the helper task allocates.

    See :ref:`microkernel_task_irqs`.

 When an ISR offloads work to a fiber there is typically a single
 context switch to that fiber when the ISR completes.
 Thus, interrupt-related processing usually continues almost immediately.
 Additional intermediate context switches may be required
 to execute any currently executing fiber
 or any higher-priority fibers that are scheduled to run.

 When an ISR offloads work to a task there is typically a context switch
 to the microkernel server fiber, followed by a context switch to that task.
 Thus, there is usually a larger delay before the interrupt-related processing
 resumes than when offloading work to a fiber.
 Additional intermediate context switches may be required
 to execute any currently executing fiber or any higher-priority tasks
 that are scheduled to run.

 IDT Security
 ============

 Ideally, the IDT memory area should be protected against accidental
 modification, in the same way that text and read-only data areas
 are protected. If no dynamic interrupts are in use, i.e.
 :option:`NUM_DYNAMIC_STUBS` is 0, the IDT will be located in ROM.

 APIs
 ****

 These are the interrupt-related Application Program Interfaces.

 :c:func:`irq_connect_dynamic()`
    Registers a dynamic ISR with the IDT and interrupt controller.

 :c:func:`irq_enable()`
    Enables interrupts from a specific IRQ.

 :c:func:`irq_disable()`
    Disables interrupts from a specific IRQ.

 :c:func:`irq_lock()`
    Locks out interrupts from all sources.

 :c:func:`irq_unlock()`
    Removes lock on interrupts from all sources.

 Macros
 ******

 These are the macros used to install a static ISR.

 :c:macro:`IRQ_CONNECT()`
    Registers a static ISR with the IDT.
	.. _nanokernel_interrupts:

	Interrupt Services
	##################

	Concepts
	********

	:abbr:`ISRs (Interrupt Service Routines)` are execution threads
	that run in response to a hardware or software interrupt.
	They are used to preempt the execution of the
	task or fiber running at the time of the interrupt,
	allowing the response to occur with very low overhead.
	When an ISR completes its normal task and fiber execution resumes.

	Any number of ISRs can be utilized in a Zephyr project, subject to
	any hardware constraints imposed by the underlying hardware.
	Each ISR has the following properties:

	* The :abbr:`IRQ (Interrupt ReQuest)` signal that triggers the ISR.
	* The priority level associated with the IRQ.
	* The address of the function that is invoked to handle the interrupt.
	* The argument value that is passed to that function.

	An :abbr:`IDT (Interrupt Descriptor Table)` is used to associate a given interrupt
	source with a given ISR.
	Only a single ISR can be associated with a specific IRQ at any given time.
	An ISR can be incorporated into the IDT when the Zephyr project is built
	(a "static ISR") or bound to the IDT when the system is up and running
	(a "dynamic ISR").

	Multiple ISRs can utilize the same function to process interrupts,
	allowing a single function to service a device that generates
	multiple types of interrupts or to service multiple devices
	(usually of the same type). The argument value passed to an ISR's function
	can be used to allow the function to determine which interrupt has been
	signaled.

	The Zephyr kernel provides a default ISR for all unused IDT entries. This ISR
	generates a fatal system error if an unexpected interrupt is signaled.

	The kernel supports interrupt nesting. This allows an ISR to be preempted
	in mid-execution if a higher priority interrupt is signaled. The lower
	priority ISR resumes execution once the higher priority ISR has completed
	its processing.

	The kernel allows a task or fiber to temporarily lock out the execution
	of ISRs, either individually or collectively, should the need arise.
	The collective lock can be applied repeatedly; that is, the lock can
	be applied when it is already in effect. The collective lock must be
	unlocked an equal number of times before interrupts are again processed
	by the kernel.

	Purpose
	*******

	Use an ISR to perform interrupt processing that requires a very rapid
	response, and which can be done quickly and without blocking.

	.. note::

	Interrupt processing that is time consuming, or which involves blocking,
	should be handed off to a fiber or task. See `Offloading ISR Work`_ for
	a description of various techniques that can be used in a Zephyr project.

	Installing an ISR
	*****************

	Use one of the following procedures to install an ISR:

	* `Installing a Static ISR`_
	* `Installing a Dynamic ISR`_

	Installing a Static ISR
	=======================

	Use a static ISR to register an interrupt handler when the interrupt
	parameters are known during the build time and the device is always
	present in the system.

	.. note::

	There is no API method to uninstall a static ISR; however, it is
	possible to replace it by installing a dynamic ISR.

	Prerequisites
	-------------

	* Ensure that the platform used by the project supports static ISRs.

	Example
	-------

	.. code-block:: c

	#define MY_DEV_IRQ 24 /* device uses IRQ 24 */
	#define MY_DEV_PRIO 2 /* device uses interrupt priority 2 */
	/* argument passed to my_isr(), in this case a pointer to the device */
	#define MY_ISR_ARG DEVICE_GET(my_device)
	#define MY_IRQ_FLAGS 0 /* IRQ flags. Unused on non-x86 */

	void my_isr(void *arg)
	{
	... /* ISR code */
	}

	void my_isr_installer(void)
	{
	...
	IRQ_CONNECT(MY_DEV_IRQ, MY_DEV_PRIO, my_isr, MY_ISR_ARG, MY_IRQ_FLAGS);
	irq_enable(MY_DEV_IRQ); /* enable IRQ */
	...
	}

	Installing a Dynamic ISR
	========================

	Use a dynamic ISR to register an interrupt handler when the interrupt
	parameters can be found out only at runtime, or when a device is not always
	present in the system.

	Prerequisites
	-------------

	* Ensure that the platform used by the project supports dynamic ISRs.

	* (x86 only) Set the :option:`NUM_DYNAMIC_STUBS` configuration option
	to specify the maximum number of dynamic ISRs allowed in the project.

	* (ARC & ARM only) Enable the :option:`SW_ISR_TABLE_DYNAMIC` so that
	interrupts may be connected at runtime.

	Example
	-------

	This is an example of a dynamic interrupt for x86:

	.. code-block:: c

	#define MY_DEV_IRQ 24 /* device uses IRQ 24 */
	#define MY_DEV_PRIO 2 /* device uses interrupt priority 2 */
	#define MY_ISR_ARG 17 /* argument passed to my_isr() */
	/* IRQ flags. Interrupt is triggered by low level signal */
	#define MY_IRQ_FLAGS (IOAPIC_LEVEL \| IOAPIC_LOW)

	void my_isr(void *arg)
	{
	... /* ISR code */
	}

	void my_isr_installer(void)
	{
	...
	irq_connect_dynamic(MY_DEV_IRQ, MY_DEV_PRIO, my_isr, MY_ISR_ARG,
	MY_IRQ_FLAGS);
	...
	irq_enable(MY_DEV_IRQ);
	...
	}

	Working with Interrupts
	***********************

	Use the following:

	* `Offloading ISR Work`_
	* `IDT Security`_

	Offloading ISR Work
	===================

	Interrupt service routines should generally be kept short
	to ensure predictable system operation.
	In situations where time consuming processing is required
	an ISR can quickly restore the kernel's ability to respond
	to other interrupts by offloading some or all of the interrupt-related
	processing work to a fiber or task.

	Zephyr OS provides a variety of mechanisms to allow an ISR to offload work
	to a fiber or task.

	1. An ISR can signal a helper fiber (or task) to do interrupt-related work
	using a nanokernel object, such as a FIFO, LIFO, or semaphore.
	The :c:func:`nano_isr_XXX()` APIs should be used to notify the helper fiber
	(or task) that work is available for it.

	See :ref:`fiber_services`.

	2. An ISR can signal the microkernel server fiber to do interrupt-related
	work by sending an event that has an associated event handler.

	See :ref:`microkernel_events`.

	3. An ISR can signal a helper task to do interrupt-related work
	by sending an event that the helper task detects.

	See :ref:`microkernel_events`.

	4. An ISR can signal a helper task to do interrupt-related work.
	by giving a semaphore that the helper task takes.

	See :ref:`microkernel_semaphores`.

	5. A kernel-supplied ISR can signal a helper task to do interrupt-related work
	using a task IRQ that the helper task allocates.

	See :ref:`microkernel_task_irqs`.

	When an ISR offloads work to a fiber there is typically a single
	context switch to that fiber when the ISR completes.
	Thus, interrupt-related processing usually continues almost immediately.
	Additional intermediate context switches may be required
	to execute any currently executing fiber
	or any higher-priority fibers that are scheduled to run.

	When an ISR offloads work to a task there is typically a context switch
	to the microkernel server fiber, followed by a context switch to that task.
	Thus, there is usually a larger delay before the interrupt-related processing
	resumes than when offloading work to a fiber.
	Additional intermediate context switches may be required
	to execute any currently executing fiber or any higher-priority tasks
	that are scheduled to run.

	IDT Security
	============

	Ideally, the IDT memory area should be protected against accidental
	modification, in the same way that text and read-only data areas
	are protected. If no dynamic interrupts are in use, i.e.
	:option:`NUM_DYNAMIC_STUBS` is 0, the IDT will be located in ROM.

	APIs
	****

	These are the interrupt-related Application Program Interfaces.

	:c:func:`irq_connect_dynamic()`
	Registers a dynamic ISR with the IDT and interrupt controller.

	:c:func:`irq_enable()`
	Enables interrupts from a specific IRQ.

	:c:func:`irq_disable()`
	Disables interrupts from a specific IRQ.

	:c:func:`irq_lock()`
	Locks out interrupts from all sources.

	:c:func:`irq_unlock()`
	Removes lock on interrupts from all sources.

	Macros
	******

	These are the macros used to install a static ISR.

	:c:macro:`IRQ_CONNECT()`
	Registers a static ISR with the IDT.