| # ETH_MCUX Ethernet driver configuration options |
| |
| # Copyright (c) 2016-2017 ARM Ltd |
| # SPDX-License-Identifier: Apache-2.0 |
| |
| menuconfig ETH_MCUX |
| bool "MCUX Ethernet driver" |
| default y |
| depends on DT_HAS_NXP_KINETIS_ETHERNET_ENABLED |
| select NOCACHE_MEMORY if HAS_MCUX_CACHE |
| select ARM_MPU if CPU_CORTEX_M7 |
| select NET_POWER_MANAGEMENT if PM_DEVICE |
| help |
| Enable MCUX Ethernet driver. Note, this driver performs one shot PHY |
| setup. There is no support for PHY disconnect, reconnect or |
| configuration change. |
| |
| if ETH_MCUX |
| |
| config ETH_MCUX_USE_DTCM_FOR_DMA_BUFFER |
| bool "Use DTCM for hardware DMA buffers" |
| default y |
| help |
| Place the hardware DMA buffers into DTCM for better networking |
| performance |
| |
| config ETH_MCUX_PROMISCUOUS_MODE |
| bool "Promiscuous mode" |
| help |
| Place the Ethernet receiver in promiscuous mode. This may be useful |
| for debugging and not needed for normal work. |
| |
| config ETH_MCUX_RMII_EXT_CLK |
| bool "RMII clock from external sources" |
| help |
| Setting this option will configure MCUX clock block to feed RMII |
| reference clock from external source (ENET_1588_CLKIN) |
| |
| config ETH_MCUX_NO_PHY_SMI |
| bool "Do not use SMI for PHY communication" |
| help |
| Some PHY devices, with DSA capabilities do not use SMI for |
| communication with MAC ENET controller. Other busses - like SPI |
| or I2C are used instead. |
| |
| config ETH_MCUX_PHY_TICK_MS |
| int "PHY poll period (ms)" |
| default 1000 |
| range 100 30000 |
| help |
| Set the PHY status polling period. |
| |
| config ETH_MCUX_PHY_EXTRA_DEBUG |
| bool "Additional detailed PHY debug" |
| help |
| Enable additional PHY related debug information related to |
| PHY status polling. |
| |
| config ETH_MCUX_RX_BUFFERS |
| int "Number of MCUX RX buffers" |
| default 6 |
| range 6 16 |
| help |
| Set the number of RX buffers provided to the MCUX driver. |
| |
| config ETH_MCUX_PHY_RESET |
| bool "Reset the PHY at boot" |
| help |
| Reset the ethernet PHY at boot. Requires dts properties int-gpios and |
| reset-gpios to be present. |
| |
| config ETH_MCUX_TX_BUFFERS |
| int "Number of MCUX TX buffers" |
| default 1 |
| range 1 16 |
| help |
| Set the number of TX buffers provided to the MCUX driver. |
| |
| config ETH_MCUX_HW_ACCELERATION |
| bool "Hardware acceleration" |
| help |
| Enable hardware acceleration for the following: |
| - IPv4, UDP and TCP checksum (both Rx and Tx) |
| |
| config PTP_CLOCK_MCUX |
| bool "MCUX PTP clock driver support" |
| default y |
| depends on PTP_CLOCK || NET_L2_PTP |
| help |
| Enable MCUX PTP clock support. |
| |
| if PTP_CLOCK_MCUX |
| |
| config ETH_MCUX_PTP_CLOCK_SRC_HZ |
| int "Frequency of the clock source for the PTP timer" |
| default 50000000 if SOC_SERIES_KINETIS_K6X |
| default 50000000 if SOC_SERIES_IMX_RT10XX |
| default 24000000 if SOC_SERIES_IMX_RT11XX |
| help |
| Set the frequency in Hz sourced to the PTP timer. |
| If the value is set properly, the timer will be accurate. |
| |
| config ETH_MCUX_PTP_CLOCK_INIT_PRIO |
| int |
| default 85 |
| help |
| MCUX PTP Clock initialization priority level. There is |
| a dependency from the network stack that this device |
| initializes before network stack (NET_INIT_PRIO). |
| |
| endif # PTP_CLOCK_MCUX |
| |
| endif # ETH_MCUX |
